Lorex CVC8011 Manuel utilisateur
- Catégorie
- Des caméras de sécurité
- Taper
- Manuel utilisateur
INFORMATION - This equipment has been tested and found to comply with
limits for a Class A digital device, pursuant to part 15 of the FCC Rules & CE Rules.
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
Do NOT use power sources other than those specified.
Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and
should conform to all local codes.
The lightning flash with an arrowhead symbol, within an equilateral
triangle is intended to alert the user to the presence of uninsulated
dangerous voltage within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
WARNING - Changes or modifications not expressly approved by the
manufacturer could void the user's authority to operate the equipment.
CAUTION : To prevent electric shock and risk of fire hazards:
Super DNR High Resolution Color Camera
1
2
Super DNR High Resolution Color Camera Super DNR High Resolution Color Camera
3
Contents
Features
Warnings and Precautions
Names and Functions of Parts
Installation
Front
Top
Rear
4
5
9
12
9
10
11
Lens
When using a CS-Mount lens (included)
When using a C-Mount lens
Connecting to a monitor
Connecting to power
12
14
14
Components 8
Camera Operation 15
Settings 16
LENS 17
EXPOSURE 19
WHITE BALANCE 22
DAY/NIGHT 23
3DNR 25
SPECIAL 26
ADJUST 30
RESET 30
EXIT 30
CAM TITLE
D-EFFECT
MOTION
PRIVACY
SYNC
LANGUAGE
RETURN
26
28
28
29
29
30
30
Specifications 33
Limited Warranty 34
Troubleshooting 31
1/3 Super-HAD II CCD
High Resolution : 560 TV Lines
Min. illumination 0.0006Lux (F1.2, 40 IRE, Sens-Up 256x)
OSD menu control
Internal / Linelock (phase control) function
Electronic day / night function, Sens-Up function (256x)
Motion adaptive digital noise reduction (3D-DNR)
Back light compensation (BLC)
Xtended Dynamic Range (XDR)
8-Zone privacy masking function (polygonal mosaic)
32x digital zoom
Remote OSD menu control (requires optional OSD remote)
Horizontal & vertical image mirroring
Auto sensing DC12V / AC24V
The camera requires periodic inspection.
Contact an authorised technician to carry out the inspection.
Stop using your camera when you find it malfunctioning.
If the camera emits smoke or is unusually hot for a long period,
a fire may be caused.
Do not Install the camera on a surface that can not support it.
If the camera is installed on an inappropriate surface, it may fall
and cause injury.
Do not hold plug with wet hands.
It could cause an electric shock.
Do not dis-assemble the camera.
It may result in an electric shock or other hazards.
Do not use the camera close to a gas or oil leak.
It may result in a fire or other hazards.
4
Super DNR High Resolution Color Camera Super DNR High Resolution Color Camera
5
Features
Warning
6
Super DNR High Resolution Color Camera Super DNR High Resolution Color Camera
7
Precautions
Only use the camera under conditions
where temperatures are between
-10¡C and +50¡C. Be especially
careful to provide ventilation when
operating under high temperatures.
It can cause the image quality to be
poor.
Severe lighting change or flicker can
cause the camera to work improperly.
This is one of the most important parts of
the camera. Be careful not to leave
fingerprints on the lens cover.
Do not install the camera in
extreme temperature conditions.
Do not install or use the camera in an
environment where the humidity is high.
Do not install the camera under
unstable lighting conditions.
Do not touch the front lens of the
camera.
It can cause malfunctions to occur.
If it gets wet, wipe it dry immediately.
Liquids can contain minerals that
corrode the electronic components.
If exposed to radioactivity the CCD
will fail.
It can damage the CCD.
Do not expose the camera to rain
or spill beverage on it.
Do not expose the camera to
radioactivity.
Never keep the camera pointed
directly at strong light.
Do not drop the camera and protect
it to physical shocks.
Note
If the camera is exposed to spotlight or object reflecting strong light,
smear or blooming may occur.
Please check that the power satisfies the normal specification before
connecting the camera.
8
Super DNR High Resolution Color Camera Super DNR High Resolution Color Camera
9
Components
Names and Functions of Parts
Front
Lens protection cap
Cover the lens when not in use.
CS-Mount lens adaptor
Attach the CS-Mount lens here.
Back Focus clamp screw
Loosen the clamp screw with a screwdriver before adjusting the Back
Focal length.
1. COLOR BOX CAMERA
2. L-WRENCH
3. C-MOUNT ADAPTOR
9. INSTRUCTION GUIDE
4. LENS
5. MOUNTING BRACKET
6. CABLE
8. ADAPTOR
3.0~8.0mm Auto Iris DC Lens-CS Type
65ft BNC Extension Cable
12V DC 300mA Regulated Power Supply
7. BNC TO RCA ADAPTOR
10
Super DNR High Resolution Color Camera Super DNR High Resolution Color Camera
11
■ Names and Functions of Parts
Names and Functions of Parts ■
IRIS JACKOSD EXTRA
POWER
DC
VIDEO SET
VIDEO OUT
AC24V IN
DC12V IN
⑪
⑤ ⑥ ⑦⑧
⑨⑩
Rear
⑤
Auto iris lens connector
Connection terminal for an auto iris lens.
⑥
Auto iris lens selection switch
Used to change between DC or Video depending upon the type of auto
iris in use.
⑦
OSD Extra
Connect to remote controller (optional -model # ACCRC01) to do camera
set up from the ground instead of on the ladder. Also includes BNC spot
video out to connect to a service monitor.
⑧
Video output terminal
Sends video signals and connects to the video input terminal of the monitor.
⑨
Power lamp
Lights up when the correct power is supplied to the camera.
⑩
Setting button
●
SET button : Used for the menu display. This button can be used to
confirm settings after changing the value of the selected function or
current conditions.
●
UP & DOWN buttons : Used for selecting items by moving the cursor
up or down on the menu screen.
●
LEFT & RIGHT buttons : Used when changing item values, by moving
the cursor to the left or right on the menu screen.
⑪
Power input terminalLow voltage power connection.
Top
④Mounting Bracket
Use the screw holes provided when fixing the
camera onto a mounting bracket. Use the clamp
screw as shown in the picture.
※
The mounting bracket can be attached to either
the bottom or the top of the camera.
Be careful not to tighten the screws more than
5mm into the body, otherwise serious damage
can occur.
L
④
12
Super DNR High Resolution Color Camera Super DNR High Resolution Color Camera
13
Installation
Installation
The camera is supplied with a DC varifocal lens. Lenses, such as
auto iris, CS-Mount and C-Mount, are compatible with this camera.
Lens
Note
Using a DC auto iris lens is recommended to achieve the best
possible results from the camera.
Please keep the lens clean.
Foreign objects or fingerprints on the lens will result in inferior image
quality, especially in low light level conditions.
1. Insert the connection plug connected to the auto iris lens cable into
the auto lens connector jack, which is located on the rear of the camera.
2. Set the lens selection switch, located on
the rear of the camera, to either DC or VIDEO,
depending on the type of auto iris lens being
used.
IRIS JACK OSD EXTRA
POWER
DC
VIDEO SET
VIDEO OUT
AC24V IN
DC12V IN
Remove the lens protection cap and attach
the CS-Mount lens to the camera by screwing it in
clockwise.
Note
Use the specified lens connection parts as shown in the picture below.
Using of the wrong sized parts may cause damage
to the inside of the camera or result in poor fitting.
Using a lens which is too heavy affects the balance
of the camera and may cause a malfunction. Please
use a lens that weighs less than 450g.
Select Av mode, if possible, when adjusting
the automatic light control (ALC) of an auto lens.
Use of PK mode may cause hunting.
When using a CS-Mount lens (included)
1. Remove the lens protection cap and
attach the C-mount adaptor.
2. Attach the C-Mount lens to the
camera by screwing it in clockwise.
When using a C-Mount lens
Installation Camera Operation
14
Super DNR High Resolution Color Camera Super DNR High Resolution Color Camera
15
AC24V IN
DC12V IN
Connect the video output terminal located on the rear of the camera
to the monitor.
The connection method varies depending on the type of monitor and
accessories. Please refer to the monitor user manual.
Turn off the power when connecting.
Connecting to a monitor
Check the standard power requirement before connecting to power.
Connecting to power
IRIS JACK OSD EXTRA
POWER
DC
VIDEO SET
VIDEO OUT
AC24V IN
DC12V IN
AC24V IN
DC12V IN
IRIS JACK OSD EXTRA
POWER
DC
VIDEO SET
VIDEO OUT
AC24V IN
DC12V IN
POWER
Dual Power Type
(AC 24V/DC 12V, AC 24V Class2)
DC Power Type (DC 12V, 300mA)
IRIS JACK OSD EXTRA
POWER
DC
VIDEO SET
VIDEO OUT
AC24V IN
DC12V IN
POWER
Menu
SETUP menu
LENS (selection)
EXIT
MANUAL DC/VIDEO
EXPOSURE
SHUTTER AGC SENS-UP
BLC HSBLC D-WDR
WHITE BAL
ATW AWB AWC MANUAL
DAY NIGHT
COLOR AUTO EXT B/W
3DNR
ON OFF
SPECIAL
CAMTITLE D-EFFECT RS-485
MOTION PRIVACY LANGUAGE
SYNC
FACTORY RESET
RESET
ADJUST
SHARPNESS BLUE RED
SETUP
LENS DC
EXPOSURE
WHITE BAL
SETUP
LENS DC
EXPOSURE
WHITE BAL
DAY NIGHT
3DNR
SPECIAL
ADJUST
RESET
EXIT
B/W
ON
3. Set up a selected item by using the Left and Right buttons.
4. To finish and save the settings, select 'EXIT' and press the SET button.
This function is used to adjust the brightness of the screen.
1.
When the SETUP menu screen is displayed on the screen, position
the cursor to point to LENS using the Up and Down buttons.
2. Select the type of lens using the Left and Right buttons.
Select the desired menu
item by using the UP and
DOWN buttons.
Modes can be changed
using the LEFT and
RIGHT buttons.
LENS
Note
•An item with the icon also has sub-menus. To select a sub-menu,
press the SET button.
• An item with the - - - icon has no sub-menus available for selection.
16
Super DNR High Resolution Color Camera Super DNR High Resolution Color Camera
17
How to Use the Camera
Settings can be made using the 5 buttons located on the rear of the camera
Settings
IRIS JACK OSD EXTRA
POWER
DC
VIDEO
SET
VIDEO OUT
AC24V IN
DC12V IN
SET
1. Press the SET button
The Setup menu is displayed on the monitor screen.
2. Select a menu item using the Up and Down buttons.
Place the cursor over a desired item.
SETUP
LENS DC
EXPOSURE
WHITE BAL
DAY NIGHT
3DNR
SPECIAL
ADJUST
RESET
EXIT
B/W
ON
How to Use the Camera
Note
DC/VIDEO : Auto Iris Lens selection. (DC lens included)
•
When using an auto iris lens, the setting of the auto iris lens selection
switch, located on the back of the camera, must be on DC or VIDEO
depending on the type of the lens which being used.
(Refer to the picture on page 13)
•
The brightness of the screen can be adjusted in DC mode.
The brightness can be adjusted within the range of 0 ~100.
The optimum level of brightness can be achieved using this adjustment.
• If you press the Set button in "MANUAL LENS", You can Adjust
brightness in EXPOSURE.
•
If you press the Set button in "DC/VIDEO", You can't adjust brightness
in EXPOSURE, Return to "LENS" and adjust brightness.
MANUAL : Manual Lens selection.
RETURN
LENS
RET
BRIGHTNESS 40
3. Press the SET button to return to the previous menu.
18
Super DNR High Resolution Color Camera Super DNR High Resolution Color Camera
19
1. When the SETUP menu screen is displayed select EXPOSURE using
the Up and Down buttons.
2. Select the desired mode using the Left and Right buttons.
SHUTTER
1.The shutter speed is controlled manually.
2. Select 'FLK' mode when flickering occurs on the screen due to an
imbalance between illumination and frequency.
NTSC Model:1/100, PAL Model: 1/120
EXPOSURE
SETUP
LENS DC
EXPOSURE
WHITE BAL
DAY NIGHT
3DNR
SPECIAL
ADJUST
RESET
EXIT
B/W
ON
EXPOSURE
SHUTTER
BRIGHTNESS
AGC
SENSE-UP
BLC
D-WDR
RETURN
1/50
MIDDLE
AUTO
OFF
OFF
RET
20
Super DNR High Resolution Color Camera Super DNR High Resolution Color Camera
21
How to Use the Camera
AGC (AUTO GAIN CONTROL)
The higher the gain level, the brighter the screen - but the higher the noise.
- OFF,LOW,MIDDLE,HIGH can be selected
SENS-UP
When it is night or dark, the camera automatically detects the light level
and maintains a clear picture if this mode is activated.
- OFF : Deactivates the SENS-UP function.
- AUTO : Activates the SENS-UP function.
BLC (Back Light Compensation)
When there is a strong backlight behind the object, clear images of the
background as well as the object can still be obtained by using the
BACKLIGHT function.
SENS-UP
SENS-UP
RETURN
X8
RET
EXPOSURE
SHUTTER
BRIGHTNESS
AGC
SENSE-UP
BLC
D-WDR
RETURN
1/50
MIDDLE
AUTO
BLC
OFF
RET
BLC ON BLC OFF
EXPOSURE
SHUTTER
BRIGHTNESS
AGC
SENSE-UP
BLC
D-WDR
RETURN
1/50
MIDDLE
AUTO
OFF
OFF
RET
BRIGHT LIGHT COMPENSATION (HSBLC)
The CVC8011 is equipped with Bright Light Compensation technology
(HSBLC) which effectively blocks strong light sources (such as car
headlights) by digitally masking them. The result is a clearer and
brighter view of the areas surrounding the strong light source.
XTENDED DYNAMIC RANGE (D-WDR)
In strong backlight or high contrast scenes, most conventional CCTV
cameras lose details in the darker portions of the image. The CVC8011
compensates for this loss in image detail by utilizing Xtended Dynamic
Range technology (D-WDR) to brighten up darker areas of the image
to regain definition and detail.
RETURN : Saves the FUNCTION menu and returns to the SETUP menu.
HSBLC OFFHSBLC ON
HSBLC MASKING
3. Select the desired mode using the Left and Right buttons and press
the SET button.
BLC
GAIN
DEFAULT
LEFT/RIGHT
WIDTH
TOP/BOTTON
HEIGHT
RETURN
MIDDLE
2
4
3
3
RET
HSBLC
LEVEL
DEFAULT
LEFT/RIGHT
WIDTH
TOP/BOTTON
HEIGHT
RETURN
8
2
4
3
3
RET
SETUP
LENS DC
EXPOSURE
WHITE BAL ATW
DAY NIGHT
3DNR
SPECIAL
B/W
ON
WHITE BAL MANUAL
BLUE
RED
RETURN
21
15
RET
Note
•
Under the following conditions White Balance may not work properly.
In such cases, select the AWC mode.
When the color temperature of the subject environment has a very
high temperature range (e.g. clear sky, or sunset)
When the ambient illumination of the subject is low.
If the camera is directed toward a fluorescent light, or is installed in
a place where illumination changes dramatically, the White Balance
operation may become unstable.
Pictures can be displayed in either color or black and white.
1. When the SETUP menu screen is displayed, select 'DAY/NIGHT' using
the Up and Down buttons.
DAY/NIGHT
22
Super DNR High Resolution Color Camera Super DNR High Resolution Color Camera
23
How to Use the Camera
WHITE BALANCE
Use the White Balance function to adjust the screen colors.
1.
Position the cursor to point to WHITE BAL on the SETUP menu screen,
select using the Up and Down buttons.
2. Select the desired mode using the Left and Right buttons.
ATW(Auto Tracking White Balance) : This mode can be used within
the color temperature range 2,000 K ~ 9500 K
AWB(Automatic White Balance) : This mode can be used within the
color temperature range 1,800 K ~ 11,000 K
AWC SET : To obtain the optimum state under the current luminance
levels, direct the camera to point toward a sheet of white paper
and press the SET button. If the environment changes, including
the light source, the white balance will require re-adjustment.
MANUAL : The manual adjustment mode enables finer adjustment.
Select ATW or AWB first then change to manual adjustment mode
and press the SET button. Set the appropriate color temperature
then increase / decrease the red and blue colour values and monitor
the color changes of the object.
SETUP
LENS DC
EXPOSURE
WHITE BAL ATW
DAY NIGHT
3DNR
SPECIAL
ADJUST
RESET
EXIT
B/W
ON
How to Use the Camera
Note
• When using a Video Auto Iris Lens, if the lens level is too low,
automatic switching between Color and Black & White may not occur.
• If you press the Set button in "AUTO", AGC is disabled.
• The camera focus will "shift" marginally under infrared illumination
at night. Always use an IR Corrective extra-low dispersion lens to
obtain sharp pictures in color and monochrome.
2. Select the desired mode using the Left and Right buttons.
COLOR : The color mode is selected as the default, and the camera
does not change automatically.
AUTO : This camera has a function which automatically changes to
the appropriate mode dependant on lighting levels. COLOR mode
is selected during daylight and B/W mode at night time.
(Set START LEVEL and END LEVEL manually, as appropriate environment.)
EXTERN : This mode allows the application of a filter to external signals.
B/W : Discards the color information and displays in black and white.
DAY NIGHT AUTO
DELAY
S-LEVEL
E-LEVEL
RETURN
5
55
65
RET
24
Super DNR High Resolution Color Camera Super DNR High Resolution Color Camera
25
Note
•When adjusting the noise reduction level in DNR mode, remember
that the higher the level is set, the greater the reduction in noise level,
but it also increases the possibility of ghosting.
3D Digital Noise Reduction (3D-DNR)
3DNR
DELAY
RETURN
50
RET
This function reduces the background noise in a low luminance environment.
1.
When the SETUP menu screen is displayed, select 'DNR' using the
Up and Down buttons.
2. Select a desired mode using the Left and Right buttons.
OFF : Deactivates DNR. Noise is not reduced.
ON : Activates DNR so that noise is reduced.
3.
Set the DNR mode to 'ON' and press the SET button. The noise reduction
level can now be adjusted.
SETUP
LENS DC
EXPOSURE
WHITE BAL
DAY NIGHT
3DNR
SPECIAL
ADJUST
RESET
EXIT
B/W
ON
26
Super DNR High Resolution Color Camera Super DNR High Resolution Color Camera
27
How to Use the Camera
SPECIAL
1. When the SETUP menu screen is displayed, select 'SPECIAL' using
the Up and Down buttons.
2. Select the desired mode using the Left and Right buttons.
CAM TITLE: If a title is entered, the title appears on the monitor.
When the SPECIAL menu screen is displayed, use the Up and Down
buttons to point the cursor to ' CAM TITLE '.
Set to 'ON' using the Left and Right buttons.
SETUP
LENS DC
EXPOSURE
WHITE BAL
DAY NIGHT
3DNR
SPECIAL
ADJUST
RESET
EXIT
B/W
ON
SPECIAL
CAM TITLE
D-EFFECT
RS485
MOTION
PRIVACY
SYNC
LANGUAGE
RETURN
OFF
ON
OFF
INT
ENGLISH
RET
Note
• When the CAM TITLE menu is 'OFF', no title will be displayed on the
monitor screen even if one has been entered.
Note
•If the cursor is moved to CLR and the SET button pressed, all letters
are deleted. To edit a letter, change the cursor to the bottom left arrow
and press the SET button. Move the cursor over the letter to be edited,
move the cursor to the letter to be inserted and then press the SET button.
Press the SET button.
Use the 4 directional buttons to move to a chara cter, and select
it by pressing the SET button. Repeat this action to enter multiple
characters. Up to 15 alphanumeric characters can be used.
SPECIAL
CAM TITLE
D-EFFECT
RS485
MOTION
PRIVACY
SYNC
LANGUAGE
RETURN
OFF
ON
OFF
INT
ENGLISH
RET
CAM LITLE
0123456789
BCDEFGHIJK
LMNOPQRSTUV
WXYZ ( )
/=&:~,.
CLR POS END
HAWK
28
Super DNR High Resolution Color Camera Super DNR High Resolution Color Camera
29
How to Use the Camera
- FREEZE : View still pictures.
- MIRROR : MIRROR,V-FLIP,ROTATE can be selected.
-
D-ZOOM : OFF(X1), ON(X2 to X32) can be selected.
-
GAMMA : Users can change the gamma settting in 0.5 steps,
between 0 and 1.0
-
NEG.IMAGE : NEGATIVE IMAGE or POSITIVE IMAGE can be selected.
MOTION DETECTION:
This product has a feature that allows you to observe movements
of objects in 4 different areas on the screen, and the green shape
appear. on the screen when movement is detected; hence a single
individual can conduct supervision efficiently. The camera detects
an object's movement by sensing disparity of outline, and level of
brightness and color.
D-EFFECT
D-EFFECT
FREEZE
MIRROR
D-ZOOM
GAMMA
NEG.IMAGE
RETURN
OFF
OFF
OFF
0.45
OFF
RET
MOTION
AREA SELECT
AREA DISPLAY
LEFT/RIGHT
WIDTH
TOP/BOTTON
HEIGHT
SENSITIVITY
MOTION VIEW
RETURN
AREA1
ON
13
32
4
24
34
OFF
RET
PRIVACY : Hide an area so that it is not displayed on the monitor.
Set up using the 4 directional buttons.
- AREA SELECT : Up to 8 areas are selectable.
-
AREA DISPLAY : Determines whether to use the area selected in the
AREA SEL, and the size and position of the area.
SYNC : In areas where the supply is 60Hz, synchronisation function
(Line-Lock),multiple cameras using the power synchronisation function
(Line-Lock),without using a synchronisation signal generator.
- INT : Internal Synchronisation Type
- L/L : Power Synchronisation Type, Line-lock
Press the SET button.
Select a phase between 0 and 359.
- COLOR : Determine area color. Select any colors of 16.
-
RETURN : Select this to save the PRIVACY menu settings and
return to the SPECIAL menu.
Please select the area you wish to observe from the 4 areas in
AREA SELECT mode.
Please select ON mode for the chosen area.
Please adjust the size of the area to be observed by using the
LEFT/RIGHT, WIDTH,TOP/BOTTOM,HEIGHT button.
Please adjust the level of observation by using SENSITIVITY mode.
Please press the RETURN button to save the changes and complete
the setting.
MOTION
AREA SELECT
AREA DISPLAY
LEFT/RIGHT
WIDTH
TOP/BOTTON
HEIGHT
COLOR
RETURN
AREA1
ON
8
16
8
16
0
RET
SYNC
PHASE
RETURN
0
RET
30
Super DNR High Resolution Color Camera Super DNR High Resolution Color Camera
31
How to Use the Camera
ADJUST
RESET
LANGUAGE
Users can select their preferred language for the OSD menu from
either, English, Korean, Chinese (Big5), Chinese (Simplified) or
Japanese.
RETURN : Select this to save the SPECIAL menu settings and
return to the SET UP menu.
RESET : Resets the camera settings to the factory defaults.
EXIT
Press the SET button in the EXIT menu to save the current settings and
exit the SET menu.
Sharpness : The sharpness of the image can be adjusted using the
left and right buttons. (32 steps)
BLUE : The blue color can be increased/decreased using the left
and right buttons. (100 steps)
RED : The red color can be increased/decreased using the left
and right buttons. (100 steps)
ADJUST
SHARPNESS
BLUE
RED
RETURN
17
88
88
RET
Troubleshooting
If you have trouble operating your camera, refer to the following table.
If the guidelines do not enable you to solve the problem, contact an
authorized technician.
Problem
Nothing appears on
the screen.
The image on the
screen is dim.
•Check the power connections.
•Check the VIDEO signal line connection.
•
Make sure the lens is clean. Clean the lens with a
soft clean lint free cloth.
•Adjust the monitor contrast & brightness controls.
•
Re-position the camera if necessary.
The image on the
screen is dark.
•Adjust the contrast control of the monitor.
•
If you have an intermediate device, set the 75/ Hi-z
properly.
The camera is not working
properly, and the surface
of the camera is hot.
•Check that an appropriate power source is
connected to the camera.
The DAY/NIGHT menu
does not work.
•Check that AGC in the EXPOSURE menu is set
to 'OFF'.
The SENS-UP function
does not work.
•Check that AGC in the EXPOSURE menu is not
set to 'OFF'.
•Check that SHUTTER in the EXPOSURE menu
is not set to 'FLK' or 'MANUAL'.
Solution
Troubleshooting
32
Super DNR High Resolution Color Camera Super DNR High Resolution Color Camera
33
Problem
The Motion Detection
function does not
work.
Color is not correct.
•Check that MOTION DEF of SPECIAL SETUP
menu is 'OFF'.
•Check the setting of WHITE BAL SETUP menu .
The screen flickers
continually.
•Check that direction of camera turns toward the
Sun.
Solution
Specifications
O.S.D
Lens Mount
Operating Temperature / Humidity
Storing Temperature / Humidity
Dimension
Weight
English, Korean, Chinese (Big5)
Chinese (Simplified) or Japanese
NTSC
CCD
Sync
Power Source
E
L
E
C
T
R
I
C
A
L
SONY 1/3" Super HAD High Sensitivity Color CCD
811(H) x 508(V)
768(H) x 494(V)
2:1 Interlace
Internal / Line Lock
Horizontal : 15.734 KHz, Vertical:59.94 Hz
CS Mount (Easy Focus type)
(C Mount is mountable by using adaptor)
OFF / BLC / HSBLC
560 TV Lines
52 dB (AGC Off, Weight ON)
0.15Lux(40IRE Color), 0.0006Lux(40IRE Sense-upX256) at F1.2
ATW / AWB / AWC / Manual
1/60 ~ 1/120,000 sec
AUTO / OFF (Selectable x2 ~ x256)
LOW / MIDDLE / HIGH / OFF
ON / OFF
ON / OFF (4 Zone, ALARM Output)
ON / OFF (8 Zones)
ON / OFF
ON / OFF
ON / OFF
ON / OFF (Level Adjustable)
DC / Video
COLOR / Black& White / AUTO / EXT
ON(x32) / OFF
-10 C to + 50 C / 30% to 80% RH
-20 C to + 60 C / 20% to 90% RH
63.7(W) 55.7(H) 87.4(D)mm
Appro. 240g
Size
Total Pixels
Effective Pixels
Scanning System
Synchronisation
Frequency
Back-light Comp.
Resolution
S/N (Y signal)
Min. Illumination
White Balance
Electronic Shutter
Speed
Sens-up
Gain Control
DNR
Motion Detection
PRIVACY
V-REV
H-REV
FREEZE
SHARPNESS
IRIS Control
Day & Night
Digital Zoom
DC12V Only (Max.160mA)
AC24V / DC12V (Max.170mA / Max.260mA)
34
Super DNR High Resolution Color Camera Super DNR High Resolution Color Camera
35
■ Limited Warranty
LOREX PRODUCT LIMITED WARRANTY
Lorex warrants, to the original retail purchaser only (the "Purchaser"), that this item (the "Product")
if properly used and installed, and where applicable, the CD-ROM on which the accompanying software
is provided, is free from manufacturing defects in material and workmanship, provided the Product is
used in normal conditions and is installed and used in strict accordance with the instructions contained.
This warranty shall be for the following warranty periods (the "Warranty Period"), commencing on the
date the Purchaser buys the Product at retail in an unused condition.
Parts and Labor : 1 year (Warranted parts do not include Bulbs, LED's and Batteries)
Lorex's obligations under this warranty shall be limited to
ㆍThe repair and or replacement of the product by means of hardware and/or software (at option of Lorex);
ㆍThe replacement of any warranted parts found by Lorex to be defective in the Product or, in Lorex's
sole discretion, the replacement of the Product found be Lorex to be defective.
ㆍIf Lorex is unable to repair or replace the Product or CD-ROM, refund the then-current value of the Product.
Any replacement parts furnished by Lorex in connection with this warranty shall be warranted to the
Purchaser for a period equal to the un expired portion of Warranty Period for the Product.
Warranty Exclusions
This warranty does not apply to Bulbs, LED's and Batteries supplied with or forming part of the product.
This warranty is invalidated if other than Lorex accessories are or have been used in or in connection with the
Product or in any modification or repair is made to the Product by other than a service depot authorized by Lorex.
This warranty does not apply to defects or damages arising by use of the Product in other than normal
(including normal atmospheric, moisture and humidity) conditions or by installation or use of the Product
other than in strict accordance with the instructions contained in the Product's Owner's Manual. This warranty
does not apply to defects in or damages to the Product caused by (i) negligent use of the Product,
(ii) misuse, abuse, neglect, alteration, repair or improper installation of the Product, (iii) electrical short
circuits or transients, (iv) Purchaser usage not in accordance with product installation, (v) use of replacement
parts not supplied by Lorex (vi) improper Product maintenance, or (viii) accident, fire, flood or other Acts of God.
This warranty does not cover the performance or functionality of any computer software included in the
package with the Product. This warranty only covers defects in the CD-ROM media such as a broken or
a defect in the CD-ROM that would prevent the CD-ROM from being read by your personal computer's
CD-ROM drive. Lorex makes no warranty that the software provided with the Product will function without
interruption or otherwise be free of anomalies, errors or 'Bugs'. Lorex makes no warranty with regard to
any software provided with the Product unless specifically set forth otherwise in a license agreement
accompanying such software. This warranty does not cover any costs relating to removal or replacement
of any Product, CD-ROM, or software installed on your computer.
Lorex reserves the right to make changes in design or to make additions to or improvements in its products
without incurring any obligation to modify any product which has already been manufactured. Lorex will
make every effort to provide updates and fixes to its software via its website. This warranty does not cover
any alteration or damage to any other software that may be or may become resident on the users system
as a result of installing the software provided. This warranty is in lieu of other warranties, express or implied,
and Lorex neither assumes nor authorizes any person to assume for it any other obligation or liability in
correction with the sale or service of the Product. In no event shall Lorex be liable for any special or
consequential damages arising from the use of the Product or arising from the malfunctioning or non-functioning
of the Product, or for any delay in the performance of this warranty due to any cause beyond its control.
This warranty shall not apply to the appearance or accessory items including, but not limited to cabinets,
cabinet parts, knobs etc., and the uncrating, setup, installation or the removal and reinstallation of products
after repair.
Lorex does not make any claims or warranties of any kind whatsoever regarding the Product's potential,
ability or effectiveness to prevent minimize, or in any way affect personal or property damage or injury.
Lorex is not responsible for any personal damage, loss or theft related to the Product or to its use for any harm,
whether physical or mental related thereto. Any and all claims or statements, whether written or verbal, by
salespeople, retailers, dealers or distributors to the contrary are not authorized by Lorex, and do not affect
this provision of this warranty.
Lorex's responsibility under this, or any other warranty, implied or expressed, is limited to repair, replacement
or refund, as set forth above. These remedies are the sole and exclusive remedies for any breach of
warranty. Lorex is not responsible for direct, special, incidental, or consequential damages resulting
from any breach of warranty or under any other legal theory including but not limited to, loss profits,
downtime, goodwill, damage to or replacement of equipment and property and any costs of recovering,
reprogramming or reproducing any program or data stored in or used with a system containing the
Product CD-ROM or accompanying software.
Lorex does not warrant that the software will operate with any other software except that which is indicated.
Lorex cannot be responsible for characteristics of third party hardware or software which may effect
the operation of the software included.
The purchaser may have other rights under state, provincial, or federal laws and where the whole or
part of any item of this warranty is prohibited by such laws, it shall be deemed null and void, but the
remainder of the warranty shall remain in effect.
All expressed and implied warranties are limited in duration to the limited warranty period. No warranties
apply after that period. Some states do not allow limitation on how long an implied warranty lasts, so
this limitation may not apply to you. Some states do not allow the exclusion or limitation of incidental
or consequential damages, so the above warranty may not apply to you. This limited warranty gives
you specific legal rights and you may also have other rights that vary from state to state.
Obtaining Service
In order to obtain service, please make sure that you have registered your product on-line (www.lorexcctv.com)
in the warranty registration section. Should the Product require service under this warranty, the Purchaser
must provide Lorex with a copy of his/ her original, dated bill of sale; receipt or invoice, failing which Lorex
will not perform any of its obligations under this warranty. If you return the Product and/or CD-ROM
to Lorex, you must assume the risk of damage or loss during shipment. You must use the original packaging
or the equivalent, and you must pay postage.
To claim on this warranty, proceed with the following steps.
1 Pack the Product in a well-padded sturdy carton.
2. i). If the unit was purchased in the United States proceed as follows :
a. Please contact our customer service department to obtain a return authorization number.
b. Return the unit to : Lorex Returns
c/o Russell Farrow
15 Lawrence Bell Drive, Amherst, NY 14221
ii). If the unit was purchased in Canada proceed as follows :
a. Please contact our customer service department to obtain a return authorization number.
b. Return the unit to : Lorex Service Center.
250 Royal Crest Court, Markham, Ont. L3R 3S1
iii) If the unit was purchased in Europe please visit:
www.lorexinternational.com for return instructions.
TOLL FREE CUSTOMER SUPPORT
North America: 1-888-42-LOREX (1-888-425-6739)
Local: 905-940-5355
International: 800-42-LOREX 0 (800-425-67390)
www.lorexcctv.com
Always use discretion when installing video and/or audio surveillance equipment especially when there is
perceived privacy. Inquire regarding federal, state and/or local regulations applicable to the lawful installation
of video and or audio recording or surveillance. Party consent may be required.
36
Super DNR High Resolution Color Camera Super DNR High Resolution Color Camera
37
■
Limited Warranty
GARANTIE LIMITÉE DES PRODUITS LOREX
Lorex garantit à l'acheteur original (ci-après désigné comme étant "l'acheteur") dans un magasin au
détail seulement, et que ce produit (ci-après désigné comme étant le "produit"), s'il est installé correctement
et - s’il y a lieu - utilisé conformément aux instructions ci-incluses, et le disque CDROM qui comporte
le logiciel, seront libres de tout défaut de fabrication, tant dans les pièces que la main-d'oeuvre, pourvu
que le produit soit utilisé dans des conditions normales et installé et utilisé strictement selon les instructions
incluses dans le guide qui l'accompagne.
Cette garantie couvrira la période mentionnée ci-dessous (ci-après désignée comme étant la "période
de garantie"), commençant le jour où l'acheteur se procure le produit à l'état neuf dans un magasin au détail.
Pièces et main-d'oeuvre : 1 année (les pièces couvertes n'incluent pas les
ampoules, voyants à DEL ni les piles).
Les obligations de Lorex selon les termes de cette garantie se limitent exclusivement aux points suivants :
ㆍLorex se réserve le droit de réparer ou de remplacer, sa seule discrétion, le logiciel et/ou le matériel.
ㆍLe remplacement des pièces sous garantie que Lorex estime être défectueuses dans le produit ou
le disque CD-ROM ou, à sa seule discrétion, le remplacement du produit jugé défectueux.
ㆍSi Lorex ne peut réparer ni remplacer le produit ou le disque CD-ROM, rembourser la valeur monétaire
du produit ou du disque CD-ROM en cours au moment de l'achat.
Toutes les pièces remplacées par Lorex seront couvertes pendant la période résiduelle de la garantie
dudit produit.
Exclusions de la garantie
Pour obtenir du service, veuillez vous assurer que vous avez inscrit votre produit en ligne (www.lorexcctv.com)
dans la section d'abonnement à la garantie. Cette garantie ne couvre pas les ampoules, voyants à DEL
ni les piles incluses avec le produit ou faisant partie de celui-ci.
Cette garantie deviendra nulle si des accessoires autres que ceux vendus ou distribués par Lorex
sont utilisés ou ont été utilisés conjointement avec le produit ou si des modifications ou des réparations
ont été effectuées au produit par une entité autre qu'un centre de service autorisé par Lorex.
Cette garantie ne s'applique pas aux défauts ni aux dommages survenus suite à une utilisation anormale
du produit (incluant des conditions atmosphériques et des taux d'humidité anormaux) ou suite à une
installation ou une utilisation du produit autre que celle décrite dans le guide accompagnant le produit.
Cette garantie ne s'applique pas aux défauts ni aux dommages causés au produit suite à (i) une utilisation
insouciante du produit, (ii) mauvaise utilisation, abus, négligence, modification ou mauvaise installation
du produit, (iii) court-circuits ou transitoires électriques, (iv) tout usage de l'acheteur qui ne correspond
pas à l'installation prescrite du produit, (v) l'utilisation de pièces non fournies par Lorex, (vi) un entretien
inadéquat du produit, ou (vii) tout accident, incendie, inondation ou autres désastres naturels.
Cette garantie ne couvre pas la performance ni la fonctionnalité de tout logiciel informatique inclus avec
le produit. Cette garantie ne couvre pas les défauts que pourrait contenir le support optique (disque CD-ROM)
ou magnétique (disquette), tel qu'un CD-ROM brisé ou comportant un défaut qui l'empêcherait d'être
lu adéquatement par le lecteur de disque de votre ordinateur. Lorex ne garantit pas que le logiciel fourni
avec le produit fonctionnera sans interruption ni qu'il sera libre de tout défaut, d'erreurs ou de 'bogues'.
Lorex ne garantit pas le logiciel inclus à moins que cela ne le soit mentionné spécifiquement dans l'entente
de la licence incluse avec le produit. Cette garantie ne couvre pas les frais se rapportant à l'enlèvement
ni à la réinsertion de tout produit, logiciel, périphérique ou disque CD-ROM installé sur votre ordinateur.
Lorex se réserve le droit de modifier la conception ou d'apporter des ajouts ou des améliorations à
ses produits, sans obligation de sa part de modifier les produits déjà fabriqués. Lorex fera tout en son
pouvoir pour fournir des améliorations et des réparations à son logiciel via son site web.
Cette garantie ne couvre pas les altérations ni les dommages effectues tout autre logiciel, ni les bogues
pouvant résider de faıon permanente sur le système de l'utilisateur suite l'installation du logiciel ci-inclus.
Cette garantie a préséance sur toutes les autres garanties tacites ou explicites, incluant la garantie en qualité
loyale et marchande et les aptitudes visant toute autre obligation ou responsabilité de la part de Lorex, et par les
présentes, Lorex n’autorise aucune personne ni entité à assumer pour elle nulle autre responsabilité en rapport
avec la vente de ce produit. Lorex ne sera pas tenue responsable, en aucune circonstance, des dommagesintérêts
directs ou indirects survenant de l'utilisation du produit ou suite au mauvais fonctionnement ou à l'absence
de fonctionnement dudit produit, ainsi que pour tout délai dans l'exécution de cette garantie suite à des
circonstances hors du contrôle de Lorex.
Lorex ne garantit d’aucune manière l'apparence extérieure du produit, ni les pièces ou accessoires incluant,
mais ne s'y limitant pas, le boîtier, les pièces du boîtier, les boutons, etc., ainsi que le déballage, l'installation,
l'enlèvement et la réinstallation du produit après une réparation.
Lorex ne garantit pas et ne fait aucune revendication en ce qui a trait au potentiel, à la capacité ou l'efficacité
de prévenir, réduire ou d'une façon quelconque, d'influer sur les dommages à la propriété privée ou sur
les blessures corporelles. Lorex ne sera pas tenue responsable des blessures corporelles, dommages
à la propriété personnelle, perte ni au vol se rapportant de près ou de loin au produit ou son usage dans
un cadre malveillant, qu'il soit physique ou mental. Lorex n'autorise aucunement les représentants, détaillants
ou grossistes, à faire des revendications ou des énoncés de la part de Lorex, tant par voie écrite que verbale
et ces énoncés n'influent d'aucune manière sur les clauses de cette garantie.
La seule responsabilité de Lorex, selon les termes de cette garantie, qu'ils soient tacites ou explicites,
se limite à une réparation, un remplacement ou un remboursement, selon les clauses décrites dans les
présentes. Ces recours constituent les seuls auxquels a droit l'acheteur pour les bris des clauses de la
garantie. Lorex ne sera pas responsable des dommages-intérêts spéciaux, directs ou indirects, qui résulteraient
d'un bris des clauses de cette garantie ou de toute autre convention législative, incluant mais ne s'y limitant
pas, les pertes de profits, pannes de courant immobilisant des équipements, la valeur ajoutée des biens
incorporels, les dommages effectués au produit et à la propriété ou les coûts reliés à leur remplacement,
ainsi que les frais de recouvrement, reprogrammation ou reproduction d'un programme ou des données
stockées dans un système contenant le disque CD-ROM du produit ou le logiciel qui accompagne celui-ci.
L'acheteur peut bénéficier de certains droits provinciaux ou fédéraux additionnels et toute clause de cette garantie
qui soit prohibée par de telles lois sera jugée nulle et sans effet mais les autres clauses demeureront en vigueur.
Lorex ne garantit pas que ce logiciel fonctionnera conjointement avec tout autre logiciel ou suite logicielle,
moins que cela ne soit indique. Lorex ne sera pas tenue responsable des caractéristiques ni des fonctions du
matériel ou des logiciels d'un tiers pouvant entrer en conflit avec le fonctionnement du logiciel ci-inclus.
Toutes les garanties tacites ou explicites se limitent à la durée de la garantie limitée. Aucune garantie ne sera
applicable après cette période de temps. Certains états ou provinces ne permettent pas de restrictions en ce
qui a trait aux termes d’une garantie tacite, ni d’exclusions aux dommages-intérêts directs ou indirects et il se
peut que ces restrictions ne s'appliquent pas à vous. Cette garantie donne à l’acheteur original des droits
spécifiques et il se peut que d’autres droits, variant d’un état ou d’une province à l’autre, puissent lui être conférés.
Obtention du service
Si l'acheteur a besoin de service pour son produit, selon les termes de cette garantie limitée, il doit fournir à
Lorex une copie de la facture d'achat affichant clairement la date et l'endroit où le produit a été acheté. Sans
cette preuve d'achat, Lorex ne sera pas dans l'obligation de remplir ses obligations envers l'acheteur. Si vous
retournez le produit et/ou le disque CD-ROM à Lorex, vous devez assumer le risque que ceux-ci soient endommagés
ou perdus au cours de l'expédition. Vous devez emballer le produit dans sa boîte originale ou un emballage
adéquat et vous devez défrayer les coûts d'expédition à l'une des adresses mentionnées ci-dessous.
Pour bénéficier du service sous garantie, vous devez suivre les étapes ci-dessous :
1. Emballez le produit dans une boîte solide et remplie de matériau d'expédition.
2. i) Si l'appareil a été acheté aux États-Unis, suivez ces étapes-ci :
a. Veuillez contacter notre département de service à la clientèle pour obtenir un numéro d'autorisation
pour le retour.
b. Retournez le produit à : Lorex Returns c/o Russell Farrow 15 Lawrence Bell Drive, Amherst, NY 14221
ii) Si l'appareil a été acheté au Canada, suivez ces étapes-ci :
a. Veuillez contacter notre département de service à la clientèle pour obtenir un numéro d'autorisation
pour le retour.
b. Retournez le produit à : Lorex Customer Service 250 Royal Crest Court, Markham, ON L3R 3S1
iii) Si l'unité a été achetée dans Europe veuillez visiter : www.lorexinternational.com pour les instructions de retour
COMPOSEZ LA LIGNE D’ASSISTANCE SANS FRAIS AUS CONOMMATEURS:
L'Amérique du nord: 1-888-42-LOREX (1-888-425-6739)
Local : 905-940-5355
International : 800-42-LOREX 0 (800-425-67390)
Soyez toujours très discret lorsque vous installez des systèmes de surveillance, surtout dans les endroits plus
retirés. Informezvous au sujet des lois et règlements municipaux, provinciaux ou fédéraux qui s’appliquent à
l’installation d’appareils de surveillance audio et vidéo. Il se peut que le consentement de la partie surveillée
soit exigé.
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
Lorex CVC8011 Manuel utilisateur
- Catégorie
- Des caméras de sécurité
- Taper
- Manuel utilisateur
dans d''autres langues
- English: Lorex CVC8011 User manual
- español: Lorex CVC8011 Manual de usuario
Documents connexes
Autres documents
-
Samsung SCC-B2331 Manuel utilisateur
-
Samsung SCC-B2335 Manuel utilisateur
-
-
-
-
-
-
-
-