Monogram Monogram ZBD0700 Le manuel du propriétaire

Marque: Monogram

Modèle: Monogram ZBD0700

Catégorie: Lave-vaisselle

Taper: Le manuel du propriétaire

Ce manuel convient également à

Owner’s

Manual

Dishwasher

ZBD6800

ZBD6880

ZBD6890

ZBD0700

ZBD0710

www.monogram.com

Consumer Information

Dishwasher

Your new Monogram dishwasher makes an eloquent statement of style, convenience and kitchen

planning flexibility. Whether you chose it for its purity of design, practical features or assiduous

attention to detail—or for all of these reasons—you’ll find that your Monogram dishwasher’s

superior blend of form and function will delight you for years to come.

The information on the following pages will help you operate and maintain your dishwasher

properly.

If you have any other questions, visit our Website at: www.monogram.com

Introduction

Contents

Appliance Registration . . . . . . . . . . . .3, 23, 24

Care and Cleaning . . . . . . . . . . . . . . . . . . . .15

Consumer Services . . . . . . . . . . . . . . . . . .3, 20

Model and Serial Number Location . . . . . . .3

Operating Instructions . . . . . . . . . . . . . . .6–14

Control Panel and Operation . . . . . . . .6–8

Lighting Features . . . . . . . . . . . . . . . . . . . .9

Water Temperature . . . . . . . . . . . . . . . . . .9

Rinse Agent . . . . . . . . . . . . . . . . . . . . . . . .9

Dish Preparation Prior to Loading . . . . .10

Detergents . . . . . . . . . . . . . . . . . . . . . . . .10

Dishwasher Racks . . . . . . . . . . . . . . . .11–14

Problem Solver . . . . . . . . . . . . . . . . . . . .16–19

Safety Instructions . . . . . . . . . . . . . . . . . . .4, 5

U.S.A. Warranty . . . . . . . . . . . . . . . . . . . . . .21

Canada Warranty . . . . . . . . . . . . . . . . . . . . .22

Consumer Information

Dishwasher

Before

using

your

dishwasher

Read this manual carefully. It is intended to

help you operate and maintain your new

dishwasher properly.

Keep it handy for answers to your questions.

If you don’t understand something or need

more help, there is a list of toll-free consumer

service numbers included on the Consumer

Services page in the back section of this

manual.

Visit our Website at: www.monogram.com

Write

down the

model &

serial

numbers

You can locate your model and serial numbers

on the tub wall just inside the door.

Before sending in the card, please write these

numbers here:

Model Number

Serial Number

Use these numbers in any correspondence or

service calls concerning your dishwasher.

If you received

a damaged

dishwasher

Immediately contact the dealer (or builder)

that sold you the dishwasher.

Save time

& money

Before you request service, check the Problem

Solver in the back of this manual.

It lists causes of minor operating problems that

you can correct yourself.

If you

need service

To obtain service, see the Consumer Services

page in the back of this manual.

We’re proud of our service and want you to be

pleased. If for some reason you are not happy

with the service you receive, here are steps to

follow for further help.

For customers in the USA:

FIRST, contact the people who serviced your

appliance. Explain why you are not pleased.

In most cases, this will solve the problem.

NEXT, if you are still not pleased, contact us

on our website, write all the details—including

your phone number—or write to:

Manager, Customer Relations

GE Appliances

Appliance Park

Louisville, KY 40225

For customers in Canada:

FIRST, contact the people who serviced your

appliance. Explain why you are not pleased.

In most cases, this will solve the problem.

NEXT, if you are still not pleased, write all the

details—including your phone number—to:

Manager, Consumer Relations

Camco Inc.

1 Factory Lane, Suite 310

Moncton, N.B. E1C 9M3

Junked or abandoned dishwashers are

dangerous…even if they will sit for “just a

few days.” If you are getting rid of your old

dishwasher, please follow the instructions below

to help prevent accidents.

Before You Throw Away Your Old Dishwasher:

•Take off the door of the washing compartment

or remove the door latch keeper (as shown).

IMPORTANT SAFETY INSTRUCTIONS

WARNING!

For your safety, the information in this manual

must be followed to minimize the risk of fire,

explosion, electric shock, or to prevent property

damage, personal injury, or loss of life.

•Do not tamper with controls.

•Do not abuse, sit on, or stand on the door or

dish rack of the dishwasher.

•Do not discard a dishwasher without first

removing the door or removing the door latch.

•Do not store or use combustible materials,

gasoline or other flammable vapors and

liquids

in the vicinity of this or any other appliance.

•Do not allow children to play inside, on or with

this appliance or any discarded appliance.

•Do not allow children to play around the

dishwasher when opening and closing the door

due to possibility of small fingers being pinched

in the door.

WATER HEATER SAFETY

Under certain conditions hydrogen gas may be

produced in a water heater that has not been

used for two weeks or more. HYDROGEN

GAS IS EXPLOSIVE.

If the hot water has not been used for two

weeks or more, prevent the possibility of

damage or injury by turning on all hot water

faucets and allowing them to run for several

minutes. Do this before using any electrical

appliance which is connected to the hot water

system. This simple procedure will allow any

built-up hydrogen gas to escape. Since the gas

is flammable, do not smoke or use an open

flame or appliance during this process.

PROPER DISPOSAL OF THE DISHWASHER

WARNING! RISK OF CHILD ENTRAPMENT

Door latch

keeper

PROPER INSTALLATION AND MAINTENANCE

This dishwasher must be properly installed

and located in accordance with the Installation

Instructions before it is used. If you did not

receive an Installation Instructions sheet with

your dishwasher, you can receive one by visiting

our Website at www.monogram.com

• Connect to a grounded metal, permanent

wiring system; or run an equipment-

grounding conductor with the circuit

conductors and connect to the equipment-

grounding terminal or lead of the appliance.

• Improper connection of the equipment-

grounding conductor can result in a risk

of electric shock. Check with a qualified

electrician or service representative if you are

in doubt whether the appliance is properly

grounded.

• Use supply conductors rated at least 75º C

(167º F).

• Dispose of discarded appliances and shipping

or packing material properly.

• Do not attempt to repair or replace any part

of your dishwasher unless it is specifically

recommended in this manual. All other

servicing should be referred to a qualified

technician.

• To minimize the possibility of electric shock,

disconnect this appliance from the power

supply before attempting any maintenance.

NOTE: Turning the dishwasher off does not

disconnect the appliance from the power

supply. We recommend having a qualified

technician service your appliance.

Use this appliance only for its intended purpose as

described in this Owner’s Manual.

CAUTION: Contents washed in Anti-

Bacterial cycle may be hot to the touch. Use care

before unloading.

• Use only powder, tabs or liquid detergents or wetting

agents recommended for use in a dishwasher and

keep them out of the reach of children. Cascade

Cascade Complete

and Electrasol

Automatic

Dishwashing Detergents and Jet-Dry

and Cascade

Rinse Aid

rinse agents have been approved for use

in all Monogram Dishwashers.

• Using a detergent that is not specifically designed for

dishwashers will cause the dishwasher to fill with suds.

• Locate sharp items so that they are not likely to

damage the door seal.

• Load sharp knives with the handles up to reduce the

risk of cut-type injuries.

• Do not wash plastic items unless marked dishwasher

safe or the equivalent. For plastic items not so marked,

check the manufacturer’s recommendations.

• Non-Dishware Items: Do not wash items such as

electronic air cleaner filters, furnace filters and paint

brushes in your dishwasher. Damage to dishwasher

and discoloration or staining of dishwasher may

result.

• Do not touch the heating element during or

immediately after use.

• Do not operate your dishwasher unless all enclosure

panels are properly in place.

• Close supervision is necessary if this appliance is used

by or near children.

• Load light plastic items so they will not become

dislodged and drop to the bottom of the

dishwasher—they might come into contact

with the heating element and be damaged.

WHEN USING YOUR DISHWASHER

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

Dishwasher

Control

Settings

Wash Cycles Use the arrow pads to scroll through the wash cycles. The light above or next to the

selected pad will be ON to indicate which WASH CYCLE has been selected.

NOTE: This dishwasher is equipped with an ExtraClean

™

Sensor with automatic temperature

control; therefore, cycle time and total water consumption may vary depending on soil (heavy,

medium, light) and temperature conditions.

ANTI Heavy 10.0 gallons, 93 minutes

BACTERIAL Medium 8.6 gallons, 90 minutes

Light 7.2 gallons, 90 minutes

This cycle raises the water temperature in the final rinse to sanitize your dishware.

The cycle length will vary depending on the temperature of your inlet water.

NOTE: The Anti-Bacterial cycle is monitored for sanitization requirements. If the cycle is

interrupted during or after the main wash portion or if the incoming water temperature is so

low that adequate water heating cannot be achieved, the sanitizing conditions may not be met.

In these cases, the sanitized light will not illuminate at the end of the cycle.

NOTE: NSF certified residential dishwashers are not intended for licensed food establishments.

COOKWARE Heavy 11.4 gallons, 95 minutes

Medium 10.0 gallons, 71 minutes

Light 10.0 gallons, 66 minutes

This cycle is meant for heavily soiled dishes or cookware with dried-on or baked-on soils. This

cycle may not remove burned-on foods. Everyday dishes are safe to be used in this cycle.

NORMAL Heavy 9.9 gallons, 74 minutes

Medium 7.0 gallons, 61 minutes

Light 5.6 gallons, 48 minutes

This cycle is for medium/heavily soiled dishes and glassware.

SPEED CYCLE Heavy 9.3 gallons, 36 minutes

(on some models) Medium 7.2 gallons, 36 minutes

Light 5.7 gallons, 33 minutes

This cycle is for everyday dishes and glassware.

You can locate

your model

number on the

tub wall just

inside the door.

Throughout this

manual, features

and appearance

may vary from

your model.

1 43

5 6

910

1 3

5 6

910

NSF INTERNATIONAL

Meets NSF Standard 184 Sanitization and Cleaning

performance of household spray-type dishwashers.

Control Panel

ZBD6890 and ZBD0700

ZBD6800 and ZBD6880

ZBD0710

1 43

5 6

910

CHINA Heavy 10.0 gallons, 49 minutes

CRYSTAL Medium 7.2 gallons, 36 minutes

Light 7.2 gallons, 36 minutes

This cycle is for lightly soiled china and crystal.

GLASSES Heavy 10.0 gal., 45 min.

(on some models) Medium 7.2 gal., 33 min.

Light 7.2 gal., 32 min.

This cycle is specifically designed for glasses.

PLASTICS Heavy 9.9 gal., 119 min.

CYCLE Medium 7.0 gal., 106 min.

(on some models) Light 5.6 gal., 93 min.

This cycle is specifically designed to reduce the risk of melting plastic items

and improve plastic drying for dishwasher safe plastic items.

RINSE ONLY Heavy 2.9 gallons, 7 minutes

Light 1.4 gallons, 3 minutes

For rinsing partial loads that will be washed later. Do not use detergent with

this cycle.

DELAY START— This option will allow you to delay the start time of any wash cycle for up to 8

or 24 hours (depending on model).

• Select the delay start time you want by pressing the DELAY START pad.

Multiple or continuous pressing will increment the delay hours. Select the

number of hours you want to delay the start of the cycle. Then press

START/RESET.

• After closing the door, the machine will count down and automatically start

at the correct time.

NOTE: To cancel the DELAY START selection before the cycle begins, press

the DELAY START pad until the display is blank. Pressing START/RESET will

not cancel delay hours.

ADDED HEAT— When selected, the cycle will run longer with heating elements on to improve

both wash and dry performance.

NOTE: Cannot be selected with RINSE ONLY cycle.

PRE WASH— For use with heavily soiled and/or dried-on, baked-on soils. This option

(on some models) MUST be selected PRIOR to starting the cycle. This option adds 16 minutes

to the cycle time.

NOTE: Cannot be selected with RINSE ONLY cycle.

HEATED— When selected, turns the drying heater and fan on for fast

DRY drying. This option will extend the cycle time by 30 minutes for

the ANTI-BACTERIAL cycle, 38 minutes for the NORMAL cycle and

COOKWARE cycle, 8 minutes for the SPEED cycle, 15 minutes for the

PLASTICS cycle and 30 minutes for all other cycles. When this is NOT

selected, the fan will turn on to dry your dishes without added heat—and

energy is saved.

NOTE: Cannot be selected with RINSE ONLY cycle.

LOCK — You can lock the controls to prevent any selections from being made. Or you

can lock the controls after you have started a cycle.

Children cannot accidentally start the dishwasher by touching pads with this

option selected.

To lock the dishwasher controls, press and hold the HEATED DRY pad for

3 seconds. The LOCK light will turn on. To unlock the dishwasher controls,

press and hold the HEATED DRY pad for 3 seconds. The LOCK light will

turn off.

Dishwasher

Control Panel/Operation

Status Indicator Lights

(indicators vary by model)

The Status display tells you what is happening while the dishwasher is in operation.

The lights will come ON, indicating the sequence of the dishwasher operation.

SENSING Displayed while the ExtraClean

™

Sensor is measuring the amount of soil and

temperature of water. The dishwasher will adjust the selected cycle to achieve

optimal performance.

ADD-A-DISH Displayed during prewash indicating that dishes added now will still be

cleaned.

WASHING Displayed during prewash, main wash and rinse periods.

DRYING Displayed during HEATED DRY.

SANITIZED Displayed when cycle has met sanitization conditions.

CLEAN Displayed when a wash cycle and enhancements are complete.

Time Remaining Display (on some models)

During operation, the display shows the minutes remaining until the cycle is complete. The

display may adjust the remaining time while the Sensing light is on. During a delay start, the

display will show hours of time remaining until the cycle starts.

START/RESET

START— After selecting the cycle and desired enhancements, press the START/RESET

pad to ready the dishwasher to begin the cycle. Close the door to start the

cycle or begin the DELAY START countdown. When the cycle starts, the water

fill begins and approximately 60 seconds later the wash action begins.

The dishwasher will always display your last selection and enhancements. If

you don’t want to change the settings, simply press the START/RESET pad to

ready the dishwasher and close the door to begin the cycle.

NOTE: If the START/RESET light is flashing, the cycle has been

interrupted. Light will stop flashing after the dishwasher automatically

pumps out the water. Close the door to allow the water to pump out (this

takes approximately 70 seconds). When the light stops flashing, the

dishwasher can be reprogrammed and restarted.

Also, if a power failure occurs NORMAL and HEATED DRY will automatically

be programmed. Make any new selections and press the START/RESET pad

to begin the new cycle.

RESET— Open the door slowly to prevent splash-out. Press the START/RESET pad

to cancel the cycle and close the door. Dishwasher will pump out and turn off

after 70 seconds.

NOTE: If the START/RESET light is flashing, the cycle has been

interrupted. Light will stop flashing after the dishwasher automatically

pumps out the water. Close the door to allow the water to pump out (this

takes approximately 70 seconds). When the light stops flashing, the

dishwasher can be reprogrammed and restarted.

Clean— The CLEAN light is illuminated and a double beep will sound when the

selected cycle and enhancements are complete. You may remove the dishes

at any time. Note the high-efficiency fan will run quietly for 30 minutes to

4 hours (depending on selected cycle) after the CLEAN light is illuminated

to continue drying the dishes. This can be stopped by opening the door

and pressing any keypad.

NOTE: To turn off the double beep indicator (or re-activate it if it was

previously disengaged), press the HEATED DRY pad 5 times within 3

seconds. A triple beep will sound to indicate the end-of-cycle beep option

has been toggled.

Dishwasher

Control Panel/Operation

Using the dishwasher

Dishwasher

Water

Temperature

The entering water must be at least 120°F

(49°C) and

not more than 150°F (66°C), for

effective cleaning and to prevent dish damage.

Check the water temperature with a candy or

meat thermometer. Turn on the hot water faucet

nearest the dishwasher, place the thermometer

in a glass and let the water run continuously into

the glass until the temperature stops rising.

Use a

Rinse

Agent

A rinse agent improves dry performance,

reduces spots and prevents new film build-up

on your dishes, glasses, flatware, cookware

and plastic. Jet-Dry

and Cascade Rinse Aid

are recommended rinse agents for Monogram

Dishwashers.

The rinse agent dispenser holds 3.5 oz. of rinse

agent. Under normal conditions, this will last

approximately one month. Try to keep it full,

but do not overfill.

To fill the rinse agent dispenser, make sure the

dishwasher is fully open.

Turn the dispenser cap to the left and lift it

out. Add rinse agent until the indicator window

shows full.

Clean up any spilled rinse agent with a damp

cloth. Replace the dispenser cap.

The amount of rinse agent released into the

final wash can be adjusted. The factory setting

is at the midpoint. If there are rings of calcium

(hard water) spots on dishes, try a higher

setting. If there is foaming, use a lower setting.

To adjust the setting, remove the dispenser cap;

then turn the adjuster counterclockwise to

increase the amount of rinse agent.

Rinse agent

adjuster

Indicator

window

Dispenser

cap

Lighting

Features (on

some models)

Interior Lights (on some models)

The interior Xenon lights provide better

visibility for loading and unloading. They come

on when the door is opened and turn off when

the door is latched. The lights will turn off after

15 minutes if the door remains unlatched. To

turn the lights back on latch and reopen the

door.

Do not attempt to replace the bulbs. If light

bulb replacement is necessary, please contact

the GE Answer Center for service by calling

1-800-626-2000.

End-of-Cycle Indicator Light (on some models)

The end-of-cycle indicator light is located on

the right side of the dishwasher, above the

handle. This light comes on when the selected

cycle and enhancements are complete. The

light will stay on until the door is opened. The

dishes may be removed at any time.

Note that the high-efficiency fan will run quietly

for 30 minutes to 4 hours (depending on the

selected cycle) after the end-of-cycle indicator

light is illuminated to continue drying the

dishes. Opening the door and pressing any

keypad will stop the fan.

Use only detergent specifically made for use

in dishwashers. Cascade

, Cascade Complete

and Electrasol

Automatic Dishwashing

Detergents have been approved for use in all

Monogram Dishwashers. Keep your powdered

detergent fresh

and dry. Don’t put detergent

into the

dispenser until you’re ready to wash

dishes.

All wash cycles except RINSE ONLY require

detergent in the main and pre-wash cup. The

amount of detergent to use depends on

whether your water is hard or soft. With hard

water, fill the main wash section and pre-wash

section completely. With soft water, fill both

sections halfway. When using automatic

dishwashing detergents tabs, simply place one

tab in the main wash section and close.

Protect your dishes and dishwasher by

contacting your water department and asking

how hard your water is. Twelve or more grains

is extremely hard water. A water softener is

recommended. Without it, lime can build up in

the water valve, which could stick while open

and cause flooding. Too much detergent with

soft water can cause a permanent cloudiness of

glassware, called etching.

To fill the dispenser, if the dispenser is closed,

open the cover by depressing the cover latch.

Fill the Main Wash Section with detergent. Fill

the Pre-wash section as needed. Then close the

dispenser cover.

It is normal for the cover to open partially when

dispensing detergent.

Do not use hand dish detergent.

NOTE: Using a detergent that is not

specifically designed for dishwashers will

cause the dishwasher to fill with suds. During

operation, these suds will spill out of the

dishwasher vents, covering the kitchen

floor and making the floor wet.

Because so many detergent containers look

alike, store the dishwasher detergent in a

separate space from all other cleaners. Show

anyone who may use the dishwasher the correct

detergent and where it is stored.

While there will be no lasting damage to the

dishwasher, your dishes will not get clean using

a dishwashing detergent that is not formulated

to work with dishwashers.

Detergents

Pre-wash

section

Cover

latch

Main wash

section

Using the dishwasher

Dishwasher

Dish

Preparation

Prior to

• No prerinsing of normal food soil is required.

• Scrape off hard soils, including bones,

toothpicks, skins and seeds.

• Remove large quantities of any remaining

food.

• Remove leafy vegetables, meat trimmings and

excessive amounts of grease or oil.

• Remove acidic food soils that can discolor

stainless steel.

Forget to

Add a

Dish?

A forgotten dish can be added any time before

the main wash.

1. Open the door slightly.

2. Wait until the water spray action stops. Steam

may rise out of the dishwasher.

3. Add forgotten dishes.

4. Close the door.

Loading the Racks

Dishwasher

Upper Rack

Features and appearance of racks and

silverware basket may vary from your model.

Although the upper rack is for glasses, cups

and saucers, pots and pans can be placed in

this rack for effective cleaning. Cups and

glasses fit best along the sides and should be

placed open-end down. This is also

a secure place for dishwasher plastics.

The utility shelf (on some models) may be

placed in the up or down position to add

flexibility.

A wine glass holder (on some models) secures

wine glasses for best washability. Because wine

glasses come in various sizes, after loading,

slowly push in the rack to make sure they will

clear the top of the dishwasher.

The upper rack is good for all kinds of

odd-shaped utensils. Saucepans, mixing bowls

and other items should be placed face down.

Fold-down tines (on some models) provide

flexibility for extra-large and hard-to-fit items.

Secure larger dishwasher-safe plastics over 2 tines

when possible.

Make sure small plastic items are secure so they can’t

fall onto the heater.

Be sure that items do not protrude through the bottom

of the rack and block rotation of the middle spray

arm. This could result in poor wash performance

for items in the upper rack.

Check to make sure that no items will block rotation

of the wash arm.

To load flatware, simply push the adjustable

handle to either side (on some models).

Put flatware in the removable basket with fork

and knife handles up to protect your hands.

Place spoons in the basket with handles down.

Mix knives, forks and spoons so they don’t nest

together. Distribute evenly. Small plastic items,

such as measuring spoons and lids from small

containers should go in the bottom of the

silverware basket with the silverware on top.

The one-piece silverware basket can be

placed in the front, right side or back of the

lower rack.

A variety of options are available regarding the

three-piece silverware basket (on some models)

in your dishwasher. The complete basket is

designed to fit on the right side of the lower

rack. Additionally, each end of the basket is

removable to add loading flexibility to

accommodate flatware and lower rack

capacity needs.

The lids of both end and middle baskets

(on some models) can be closed to contain

small items. Long items can be placed on the

utility shelf in the upper rack.

The standard position of your adjustable rack

is “up” which allows for maximum clearance for

your taller items in the lower rack. If you have

taller wine glasses, tumblers or other items to

place in the upper rack, you may want to adjust

the rack to the lower position.

To lower the rack, support the weight of the

rack with your hands as shown and press both

finger pads about 1/4″ toward the inside of the

rack as indicated and guide the rack down to

its lower position.

To raise the rack to the “up” position, pull up

on the center of the rack side frame until the

rack locks into place.

Loading the Racks

Dishwasher

Adjustable

Upper Rack

(on some

models)

Silverware

Basket

Don’t let any

item extend

through bottom.

To remove end baskets, grasp the basket

at opposite corners and slide apart.

One-piece basket (on some models)

Three-piece basket (on some models)

Cutlery Tray

The cutlery tray holds up to 4 large knifes such as

a carver, chef’s knives, bread knife, etc., that are

too tall to fit in the silverware basket.

Hook the tray onto the rear of the upper rack.

Lay the knives between the guides (as shown).

Bowl Tines

The special large-bowl tines in the lower rack add

flexibility to your loading pattern. They are useful

for serving bowls or other large bowls.

To use the bowl tines, fold down the 2 rows of flex

tines in front of the bowl tines and load bowls just

as you would in the upper rack.

You can remove the upper rack to allow space for

large items in the lower rack.

To remove the upper rack, push thumb tab out

and remove the front end caps on each side of

the rail.

Pull the rack straight out and off the rails.

Replace the end caps, then push the rails all the

way back into the dishwasher. Slide the shower

nozzle attachment over the spout.

Then fill the lower rack and begin your cycle.

NOTE: Nozzle must be in place with upper rack

removed. If not installed properly, poor wash

performance and noise will result.

NOTE: Don’t forget to remove the shower nozzle

attachment before you replace the upper rack.

Lower Rack

The lower rack is best used for plates, saucers and

cookware. Large items such as broiler pans and

baking racks should go along the left-hand side.

Load platters, pots and bowls along the sides, in

corners or in the back. The soiled side of items

should face the center of the rack. If necessary,

oversized glasses and mugs can be placed in the

lower rack to maximize loading flexibility.

Also, be careful not to let a portion of an item

such as a pot or dish handle extend through the

bottom rack. This could block the wash arm and

cause poor washing results.

Fold-down tines (on some models) provide

flexibility for extra-large and hard-to-fit items.

The tines may be left in the up position or folded

down to customize the lower rack.

Shower nozzle

attachment

These tines fold down

Large-bowl tines

Remove the

Upper Rack

Extra Rack

Features

(on some

models)

Loading the Racks

Dishwasher

Remove end cap

Push thumb tab

these

guidelines

for loading

10 and 12

place settings

Loading the Racks

Dishwasher

Features and appearance of racks and silverware baskets may vary from your model.

Upper Rack—10 place settings Lower Rack—10 place settings

Upper Rack—12 place settings Lower Rack—12 place settings

Care and Cleaning

Dishwasher

Exterior

To clean the control panel use a lightly dampened cloth then dry thoroughly. To clean the

exterior painted panels use a good appliance polish wax.

Never use sharp objects, scouring pads or harsh cleaners on any part of the dishwasher.

The stainless steel panels can be cleaned with CERAMA BRYTE

Stainless Steel Appliance

Cleaner or a similar product using a clean, soft cloth. You can order CERAMA BRYTE

Stainless

Steel Appliance Cleaner

through GE Parts by calling 800.626.2002 (for U.S. only). In Canada, call

1.888.880.3030.

Protect

Against

Freezing

If your dishwasher is left in an unheated place during the winter, ask a service technician to:

1. Cut off electrical power to the dishwasher. Remove fuses or trip circuit breaker.

2. Turn off the water supply and disconnect the water inlet line from the water valve.

3. Drain water from the water inlet line and water valve. (Use a pan to catch the water.)

4. Reconnect the water inlet line to the water valve.

The Air

Gap

An air gap protects your dishwasher against

water backing up into it if a drain clogs. The air

gap is not a part of the dishwasher. It is not

covered by your warranty. Not all plumbing

codes require air gaps, so you may not have one.

The air gap is easy to clean.

1. Turn off the dishwasher and lift off the

chrome cover.

2. Unscrew the plastic cap and clean with

a toothpick.

Interior

The stainless steel used to make the dishwasher tub and inner door provides the highest reliability

available in a GE dishwasher. If the dishwasher tub or inner door should be scratched or dented

during normal use, they will not rust or corrode. These surface blemishes will not affect their

function or durability.

Check the air gap any time your dishwasher

isn’t draining well.

Two types of

air gaps

PROBLEM POSSIBLE CAUSE WHAT TO DO

Control panel lights go Time too long between • Each pad must be touched within 30

off when you’re setting touching of selected pads seconds of the others. To relight, touch any

controls pad again, or unlatch and relatch door.

Noise Some of the sounds you • Detergent cup opening.

will hear are normal

• The motor stopping during the drying

period.

• Water draining out of the tub immediately

after you touch START/RESET pad.

• Dry fan running.

Utensils are not secure • Make sure everything is secured in

in the rack or something dishwasher.

small has dropped into

the rack

Motor hums • Dishwasher has not been used on a regular

basis. If you do not use your dishwasher

often, run a RINSE ONLY cycle once every

week. This will help keep the seal moist.

Detergent left in Dishes are blocking the • Reposition the dishes.

dispenser cups detergent cups

Water standing in the This is normal • A small amount of clean water around the

bottom of the tub outlet on the tub bottom at the back of the

tub keeps the water seal lubricated.

Water won’t pump out Drain is clogged • If you have an air gap, clean it.

of the tub

• Check to see if your kitchen sink is

draining well. If not, you may need a

plumber.

• If the dishwasher drains into a disposer,

run disposer clear.

Suds Correct detergent • Use only automatic dishwasher detergents

wasn’t used to avoid sudsing. Cascade

, Cascade

Complete

and Electrasol

dishwasher

detergents have been approved for use

in all Monogram dishwashers.

• To remove suds from the tub, open the

dishwasher and let suds dissipate. Add 1

gallon of cold water to the tub. Pump out

water by starting any cycle and then resetting

the unit after 10 seconds. See Control Panel

section. Repeat if necessary.

Rinse agent was spilled • Always wipe up rinse agent spills

immediately.

Stained dishwasher Detergent with colorant • Some detergents contain colorant (pigment

parts was used or dyes) that will discolor the tub interior

with extended use. Check the detergent

cup for signs of any discoloration. If cup is

discolored, change to detergent without any

colorant. Cascade

, Cascade Complete

and

Electrasol

dishwasher detergents have been

approved for use in all Monogram

dishwashers.

Some tomato-based foods • Use of the RINSE ONLY cycle after adding

can stain the dish to the load can decrease the level of

staining.

• GE also recommends Cascade

Plastic

Booster

™

to help remove these types of

stains.

Before You Call For Service

Dishwasher

Questions?

Use this

problem

solver

Questions?

Use this

problem

solver

PROBLEM POSSIBLE CAUSE WHAT TO DO

Dishes and flatware Low inlet water • Make sure inlet water temperature is correct

not clean temperature (see Using the Dishwasher section).

• Run water at the nearest faucet prior to

starting the diswasher to insure optimal water

temperature.

Water pressure is • Turn on a facucet. Is water coming out

temporarily low more slowly than usual? If so, wait until

pressure is normal before using your

dishwasher.

Air gap is clogged • Clean air gap.

Improper rack loading • Make sure large dishware does not block the

detergent dispenser or the wash arms.

• Glasses and dishes must face the spray arms.

Spots and filming on • Use Jet Dry

or Cascade Rinse Aid

rinse

glasses and flatware agent to remove spots and prevent new film

buildup.

• Install water softener.

• To remove stubborn spots and pre-existing

film from glassware:

1Remove all metal utensils from the

dishwasher.

2Do not add detergent.

3Select the COOKWARE cycle.

4Start the dishwasher and allow to run for

18 to 22 minutes. Dishwasher will now be

in the main wash.

5Open the door and pour 2 cups (500 ml)

of white vinegar into the bottom of the

dishwasher.

6Close the door and allow to complete the

cycle. If vinegar rinse doesn’t work: Repeat

as above, except use 1/4 cup (60 ml) of

citric acid crystals instead of vinegar.

Cloudiness on glassware Combination of soft water • This is called etching and is permanent.

and too much detergent To prevent this from happening, use less

detergent if you have soft water. Wash

glassware in the shortest cycle that will get

it clean.

Water temperature • Lower the water heater temperature.

entering the dishwasher

exceeds 150°F (66°C)

Black or gray marks on Aluminum utensils have • Remove marks with a mild, abrasive

dishes rubbed against dishes cleaner.

Extremely hard water

Low inlet water

temperature

Overloading the dishwasher

Improper loading

Old or damp powder

detergent

Rinse agent dispenser

empty

Too little detergent

Before You Call For Service

Dishwasher

Questions?

Use this

problem

solver

PROBLEM POSSIBLE CAUSE WHAT TO DO

Yellow or brown film Tea or coffee stains • Remove the stain by hand, using a solution

on inside surfaces of 1/2 cup bleach and 3 cups warm water.

CAUTION: Before cleaning

interior, wait at least 20 minutes after a

cycle for the heating element to cool

down. Failure to do so can result in burns.

An overall yellow or brown • A special filter in the water supply line is

film can be caused by iron the only way to correct this problem.

deposits in water Contact your GE dealer or a water softener

company

White film on inside Hard water minerals • GE recommends Jet Dry

Dishwasher

surfaces Cleaner to help remove some hard water

and mineral stains.

• For extreme staining, clean the interior by

applying dishwasher detergent to a damp

sponge. Wear rubber gloves. DO NOT use

any type of cleanser other than those

recommended or dishwasher detergent

because it may cause foaming or sudsing.

Cascade

, Cascade Complete

and

Electrasol

Automatic Dishwashing

Detergents have been approved for

use in all Monogram Dishwashers.

CAUTION: Before cleaning

interior, wait at least 20 minutes after a

cycle for the heating element to cool

down. Failure to do so can result in burns.

Dishes don’t dry Low inlet water • Make sure inlet water temperature is

temperature correct (see Using the Dishwasher

section).

• Select ADDED HEAT.

• Select HEATED DRY.

Rinse agent dispenser is • Check and refill the rinse agent dispenser.

empty

Dishwasher won’t run Fuse is blown, or the • Replace fuse or reset circuit breaker.

circuit breaker tripped Remove any other appliances from the

circuit.

• Try resetting the START/RESET pad.

Wall switch • Check for a wall switch that the dishwasher

(some installations) is in might be connected to. A wall switch is

the “off” position required by electrical codes in some

localities. Turn the switch “on” if it is “off.”

Steam This is normal • Steam comes through the vent on the

bottom of the door during drying and

when water is being pumped out.

Before You Call For Service

Dishwasher

Before You Call For Service

Dishwasher

Questions?

Use this

problem

solver

PROBLEM POSSIBLE CAUSE WHAT TO DO

Sanitized light does not The door was opened and • Do not interrupt the cycle anytime during

illuminate at the end of the cycle was interrupted or after main wash.

the cycle (Anti-Bacteria during or after the main

cycle only) wash portion

Low inlet water • Raise the water heater temperature to

temperature 120°F (49°C).

Interior lights not Door was open for more • Latch the door and reopen.

working than 15 minutes

Bulbs are burnt out • Call for service to replace bulbs.

End-of-cycle indicator Dishwasher has not • Open the door and check the status

light does not illuminate completed cycle indicator lights on control panel to

determine if cycle is complete.

Consumer Services

Dishwasher

With the purchase of your new Monogram appliance, receive the

assurance that if you ever need information or assistance from GE,

we’ll be there. All you have to do is call—toll- free!

GE Answer

Center

In the USA:

800.626.2000

Whatever your question about any Monogram major appliance, GE Answer Center

information service is available to help. Your call—and your question—will be answered

promptly and courteously. And you can call any time. GE Answer Center

service is open

24 hours a day, 7 days a week.

Visit our Website at: www.monogram.com

In Canada, call 1.888.880.3030.

In-Home

Repair Service

In the USA:

800.444.1845

In Canada:

1.888.880.3030

A GE consumer service professional will provide expert repair service, scheduled at a time

that’s convenient for you. Many GE Consumer Service company-operated locations offer you

service today or tomorrow, or at your convenience (7:00 a.m. to 7:00 p.m. weekdays, 9:00 a.m.

to 2:00 p.m. Saturdays). Our factory-trained technicians know your appliance inside and out—

so most repairs can be handled in just one visit.

Service Contracts

In the USA:

800.626.2224

In Canada:

1.888.880.3030

You can have the secure feeling that GE Consumer Service will still be there after your

warranty expires. Purchase a GE contract while your warranty is still in effect and you’ll

receive a substantial discount. With a multiple-year contract, you’re assured of future

service at today’s prices.

Parts and

Accessories

In the USA:

800.626.2002

In Canada:

1.888.880.3030

Individuals qualified to service their own appliances can have parts or accessories sent directly

to their home. The GE parts system provides access to over 47,000 parts…and all GE Genuine

Renewal Parts are fully warranted.

User maintenance instructions contained in this manual cover procedures intended to be

performed by any user. Other servicing generally should be referred to qualified service

personnel. Caution must be exercised, since improper servicing may cause unsafe operation.

For Customers

With Special

Needs…

In the USA:

800.626.2000

GE offers Braille controls for a variety of GE appliances, and a

brochure to assist in planning a barrier-free kitchen for persons

with limited mobility.

Consumers with impaired hearing or speech who have access to a

TDD or a conventional teletypewriter may call 800.TDD.GEAC

(800.833.4322) to request information or service.

www.monogram.com

La page charge ...

Monogram Monogram ZBD0700 Le manuel du propriétaire

Marque: Monogram

Modèle: Monogram ZBD0700

Catégorie: Lave-vaisselle

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Monogram Monogram ZBD0700 Owner's manual

Monogram Monogram ZBD0700 Le manuel du propriétaire

Ce manuel convient également à

Monogram Monogram ZBD0700 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents