Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
Rev. E
INST-900
This instruction sheet is for the Panasonic Toughbook L1/S1 docking station only. For
instructions on features, set-up, and operation of the Panasonic Toughbook L1/S1 tablet,
please refer to the manual provided by Panasonic with the tablet.
This docking station is designed to be used with a variety of Gamber-Johnson mounting
systems. Installation instructions for other Gamber-Johnson products are provided with
each individual product.
© Copyright 2017 Gamber-Johnson, LLC
1 / 8
Product
INSTALLATION INSTRUCTIONS
7160-1314
TOUGHBOOK L1/S1 TABLET DOCK
Revision
Form
Printing Spec:
PS-004
If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868
This instruction sheet is for the following products:
Item No. 7160-1314-00/10
No RF, Thick/Thin
Item No. 7160-1314-02/12
Dual RF, Thick/Thin
The following Power Adapters can be used to power the docking station.
They can be ordered from Gamber-Johnson seperately.
7300-0443
- Bare Wire Adapter (12-32 Vdc input)
7300-0444
- Cigarette Plug Adapter (12-32 Vdc input)
"W" and "N" switch on cigarette plug adapter is for different sizes of power ports (Wide/Narrow)
IMPORTANT SAFETY INFORMATION FOR INSTALLERS
Safety is dependent on the proper installation and servicing of this docking station. It is important to
read and follow all instructions before installing this product.
To properly install a Gamber-Johnson docking station you must have a good understanding of
automotive electrical procedures and systems, along with proficiency in the installation and service of
aftermarket vehicle equipment.
There are no adjustments required at any time of the electrical components within the docking station.
Opening the docking station will void the product warranty.
During Installation:
DO NOT
connect this docking station to the vehicle battery until:
All other electrical connections are made
1.
Mounting of all components is complete
2.
Verification that no shorts exist in the entire system
3.
DO NOT
install equipment or route wiring or cords in the deployment path of any air bag.
When drilling into the vehicle, DO make sure that both sides of the surface are clear of anything that
could be damaged.
CAUTION:
If wiring is shorted to the frame, high current conductors can cause hazardous sparks
resulting in electrical fires or flying molten metal.
After installation:
Test the docking station to ensure that it is working properly.
File these instructions in a safe place and refer to them when performing maintenance or re-
installing.
WARNING
: Failure to follow all safety precautions and instructions may result in property damage,
serious injury, or death.
PRE-INSTALLATION RECOMMENDATOINS
Conduct a "Bench Test"
Gamber-Johnson strongly advises a "bench test" be conducted to verify all electronic and
software issues are resolved prior to installation:
Make sure the computer is operational by itself.
1.
Insert computer into the docking station and verify that the computer is
2.
operating in the dock and battery is charging.
Gamber-Johnson recommends positioning of all mounts and equipment in the vehicle
prior to the actual install to verify that mounting locations are safe and practical.
2 / 8
Docking Connector
External Antenna - Dual RF
(Optional)
Release Button
Barrel Key Lock
Bottom Cavity
Guide Pins
VESA 75mm Hole Pattern
1/4-20 x 0.75" Bolts and
1/4-20 Nuts Provided
AMPS Hole Pattern
#10-32 x 0.75" Bolts and
#10-32 Nuts Provided
FEATURE IDENTIFICATON
3 / 8
Provides docking guidance
and connector protection,
prevents mis-docking
Lower Walls
Upper Walls
External Antenna Switch
USB2.0
500 mA
Power Input: 5 Vdc
PORT IDENTIFICATION
4 / 8
CABLE MANAGEMENT FEATURES AND PROPER INSTALLATION
1. Use Zip ties (provided) to secure each port cable to the specific strain relief feature on the dock
Cable Tie
Locations
Cable Tie
Locations
RF - GPS
EXT_ANT2
RF - Cell
EXT_ANT1
Toughbook FZ-L1 Barcode Reader Cover
**Included in hardware bag**
Attach Barcode Reader Cover with
included two plastic screws
DO NOT Over-tighten
Barcode Reader Cover Options
Toughbook FZ-S1 Barcode Reader Cover
**Bar code reader cover sold separetly**
Available at www.GamberJohnson.com
Part Number:
19943
Pinch Bar Code Reader Cover between
the back of docking station and mounting device
(Can be done using supplied hardware)
5 / 8
"LOCKED"
Position
"UNLOCKED"
Position
DOCKING AND UNDOCKING THE TABLET
TO DOCK THE COMPUTER
Insert the bottom of the tablet into the docking station.
1.
Rotate the top of the tablet under the blue latch until the tablet is resting inside the main housing.
2.
The blue latch will spring down in front of the tablet to hold it in place.
(Optional) For added security, with the dock in the "Latched" position, turn the lock to the "LOCKED"
position (Counter Clockwise).
TO UNDOCK THE COMPUTER
1. Turn the lock to the "UNLOCKED" position (Clockwise).
2. Push upward on the Release Button with the thumb and pull outward on the top of the tablet until it
clears the blue latch. Lift the tablet out of the dock.
6 / 8
Gamber-Johnson LLC, 3001 Borham Ave., Stevens
Point, WI, 54481, USA, 715-344-3482
Regulatory Certification Information
Regulatory Model #: 7160-1314
GJ Model #'s and Descriptions:
7160-1314-00 (No-RF, Thick) 7160-1314-10 (No-RF, Thin)
7160-1314-02 (Dual-RF, Thick) 7160-1314-12 (Dual-RF, Thin)
Certifications:
EN 55032:2012 VCCI-CISPR 32:2016 Class B
ISO 10605, Section 8, Table C.2, Cat. 2
IEC 62368-1:2014
EN 62368-1:2014 + A11:2017
CAN/CSA C22.2 No. 62368-1:2014
UL 62368-1:2014
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions. (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interfernece that
may cause undesired operation.
7 / 8
EN: Safety instructions for proper use
Precautions for Operating the Car Mounter
If a Malfunction Occurs, Immediately Unplug the Car Plug and Remove the Computer From this product
Use Only the Specified Car Adaptor With This Product
Avoid a Lot of Water, Moisture, Steam, Dust, Oily Vapors, etc
Portions of your car mounter may differ somewhat from the illustrations in the operating instructions, but this should present
no problems in actual use
For business users in the European Union.
If you wish to discard electrical and electronic equipment, please contact your dealer
or supplier for further information.
Precautions for Installing the Car Mounter
Do Not Install This Product in Unstable State
Do Not Install This Product Wherever There is a Lot of Water, Moisture, Steam, Dust, Oily Vapors, etc
DE: Sicherheitshinweise bei einer ordnungsgemäßen Nutzung
Vorsichtsmaßnahmen beim Einsatz der Fahrzeughalterung
Entfernen Sie beim Auftreten einer Fehlfunktion unverzüglich das Fahrzeugnetzteil und trennen Sie die Verbindung zwischen
Computer und dem Produkt
Verwenden Sie nur das angegebene Fahrzeugnetzteil für das Produkt
Wasser, Feuchtigkeit, Dampf, Staub, ölige Dämpfe usw. vermeiden
Einige Bereiche Ihrer Automontagevorrichtung können von den Abbildungen in der Bedienungsanleitung geringfügig
abweichen, was für die tatsächliche Nutzung jedoch unerheblich ist.
Für Kunden in der Europäischen Union.
Bitte treten Sie mit Ihrem Händler oder Lieferanten in Kontakt, wenn Sie elektrische und
elektronische Geräte entsorgen möchten. Er hält weitere Informationen für Sie bereit.
Vorsichtshinweise zum Einbau der Automontagevorrichtung
Installieren Sie das Produkt nicht in instabilem Zustand
Installieren Sie das Produkt nicht in der Umgebung von Wasser, Feuchtigkeit, Dampf, Staub, öligen Dämpfen usw.
FR: Consignes de sécurité pour une utilisation correcte
Précautions d’utilisation de auto monter
En cas de dysfonctionnement, débrancher immédiatement la fiche et déconnecter l’ordinateur de ce produit.
Ne connectez pas au port pour réseau local un câble téléphonique ou un câble réseau autre que ceux spécifiés.
Eviter le contact de l‘eau, de l’humidité, de la vapeur, de la poussière, des vapeurs graisseuses, etc.
Certaines parties de votre auto monter peuvent différer quelque peu des illustrations imprimées dans les instructions
d’utilisation mais cela ne doit présenter aucun problème lors de l’utilisation.
Utilisateurs professionnels de l’Union européenne.
Pour en savoir plus sur l’élimination des appareils électriques et
électroniques, contactez votre revendeur ou fournisseur.
Précautions à prendre pour l’installation de l’Auto monter
Ne pas installer ce produit sur un support instable
Ne pas installer ce produit en présence d’eau, d’humidité, de vapeur, de poussière, de vapeurs graisseuses,etc.
8 / 8
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

dans d''autres langues