Simplicity 01917-0 Manuel utilisateur

Marque: Simplicity

Modèle: 01917-0

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

Generator Systems

Installation & Operator’s Manual

50 Amp Automatic

Transfer Switch

192636

Revision P

Not for reproduction

2 BRIGGSandSTRATTON.COM

Thank you for your purchase of this Briggs & Stratton® Power Products automatic transfer switch. This product is designed

for use with specific home standby generators and may not function with generators produced by other manufacturers.

Seek a qualified electrical professional to determine applicability of this equipment to generators manufactured by others.

When operated and maintained according to the instructions in this manual, your system will provide many years of

dependableservice.

This manual contains safety information to make you aware of the hazards and risks associated with this system and how to

avoid them. We have made every effort to provide for a safe, streamlined and cost-effective installation. As each installation

is unique, it is impossible to know of and advise of all conceivable procedures and methods by which installation might be

achieved. We do not know all possible hazards and/or the results of each possible method or procedure. It is important that

you read and understand these instructions thoroughly before attempting to install or operate this equipment. Save these

instructions for future reference.

This transfer switch requires professional installation before use. Refer to the Installation section of this manual for

instructions on installation procedures. Only licensed electrical contractors should install transfer switches. Installations must

strictly comply with all applicable federal, state and local codes, standards and regulations. Your installer should follow the

instructions completely.

Where to Find Us

You never have to look far to find Briggs & Stratton support and service for your system. Consult your Yellow Pages.

There are many authorized service dealers who provide quality service. You can also contact Technical Service by phone at

(800) 743 4115 between 8:00 AM and 5:00 PM CT, or click on Find a Dealer at BRIGGSandSTRATTON.COM, which provides a

list of authorized dealers.

For Future Reference

Please fill out the information below and keep with your receipt to assist in unit identification for future purchase issues.

Transfer Switch

Model Number

Revision

Serial Number

Date Purchased

Not for reproduction

Table of Contents

Important Safety Instructions........................4

Installation ....................................5

Owner Orientation ............................................5

Installing Dealer/Contractor Responsibilities ........................5

Mounting Guidelines ..........................................7

Power Wiring Interconnections ..................................7

System Test .................................................8

Operation .....................................9

Maintenance ...................................9

Troubleshooting................................ 10

Schematic Diagram ..........................................11

Wiring Diagram .............................................12

Product Specifications ........................... 13

Not for reproduction

4 BRIGGSandSTRATTON.COM

Important Safety Instructions

SAVE THESE INSTRUCTIONS - This manual contains

important instructions that should be followed during

installation and maintenance of the equipment.

Safety Symbols and Meanings

The safety alert symbol indicates a potential personal

injury hazard. A signal word (DANGER, WARNING, or

CAUTION) is used with the alert symbol to designate a

degree or level of hazard seriousness. A safety symbol

may be used to represent the type of hazard. The signal

word NOTICE is used to address practices not related to

personal injury.

DANGER indicates a hazard which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazard which, if not avoided, could

result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, could

result in minor or moderate injury.

NOTICE addresses practices not related to personal injury.

The manufacturer cannot possibly anticipate every possible

circumstance that might involve a hazard. The warnings in

this manual, and the tags and decals affixed to the unit are,

therefore, not all-inclusive. If you use a procedure, work

method or operating technique that the manufacturer does

not specifically recommend, you must satisfy yourself that

it is safe for you and others. You must also make sure that

the procedure, work method or operating technique that you

choose does not render the equipment unsafe.

Electrical Shock Read Manual

NOTICE Only qualified electricians should attempt

installation of this equipment, which must strictly comply

with applicable codes, standards and regulations.

WARNING Certain components in this product and

related accessories contain chemicals known to the State

of California to cause cancer, birth defects, or other

reproductive harm. Wash hands after handling.

WARNING Low voltage wire cannot be installed in

same conduit as power voltage wiring.

• Failure to follow above warning could cause personal

injury, damage and/or malfunction of equipment.

WARNING Failure to properly ground equipment can

result in electrocution.

• Do not touch bare wires.

• Do not use equipment with worn, frayed, bare or

otherwise damaged wiring.

• Do not handle electrical cords while standing in water,

while barefoot, or while hands or feet are wet.

• If you must work around a unit while it is operating, stand

on an insulated dry surface to reduce shock hazard.

• Do not allow unqualified persons or children to operate or

service equipment.

• In case of an accident caused by electrical shock,

immediately shut down all sources of electrical power

and contact local authorities. Avoid direct contact with

the victim.

WARNING Equipment contains high voltage that can

cause personal injury or death.

• Despite the safe design of the system, operating this

equipment imprudently, neglecting its maintenance or

being careless can cause possible injury or death.

NOTICE Improper treatment of equipment can damage it

and shorten its life.

• Use equipment only for intended uses.

• If you have questions about intended use, ask dealer or

contact Briggs & Stratton Power Products.

• Do not expose equipment to excessive moisture, dust,

dirt, or corrosive vapors.

• Remain alert at all times while working on this equipment.

Never work on the equipment when you are physically or

mentally fatigued.

• If connected devices overheat, turn them off and turn off

their circuit breaker/fuse.

SAVE THESE INSTRUCTIONS

Not for reproduction

Installation

We sincerely appreciate your patronage. For this reason,

we have made significant effort to provide for a safe,

streamlined and cost-effective installation. Because each

installation is unique, it is impossible to know of and advise

the trade of all conceivable procedures and methods by

which installation might be achieved. Neither could we

know of possible hazards and/or the results of each method

orprocedure.

For these reasons, only current licensed electrical should

attempt system installations. Installations must strictly

comply with all applicable codes, industry standards

andregulations.

Your equipment is supplied with this combined “Installation

and Operator’s Manual”. This is an important document and

should be retained by the owner after the installation has

been completed.

Every effort has been made to make sure that the information

in this manual is both accurate and current. However, the

manufacturer reserves the right to change, alter or otherwise

improve the system at any time without prior notice.

Home Owner Responsibilities

To help you make informed choices and communicate

effectively with your installation contractor(s), read and

understand Owner Orientation before contracting or

starting your equipment installation.

To arrange for proper installation, contact the store at which

you purchased your equipment, your dealer, or your utility

power provider.

The equipment warranty is VOID unless the system is

installed by licensed electrical professionals.

Owner Orientation

The illustrations provided are for typical circumstances and

are meant to familiarize you with the installation options

available with your system.

Local codes, appearance, and distances are the factors that

must be considered when negotiating with an installation

professional. As the distance from the existing electrical

service increases, compensation in wiring materials must

be allowed for. This is necessary to comply with local codes

and overcome electrical voltage drops.

These factors will have a direct effect on the overall price

of your equipment installation.

Your installer must check local codes AND obtain permits

before installing the system.

• Read and follow the instructions given in this manual.

• Follow a regular schedule in caring for and using your

equipment, as specified in this manual.

Installing Dealer/Contractor Responsibilities

• Read and observe the safety rules.

• Read and follow the instructions given in this manual.

• The installer may need to provide appropriate rated

contactors based on loads to be controlled.

• Check federal, state and local codes and authority

having jurisdiction, for questions on installation.

• Ensure generator is not overloaded with selected loads.

If you need more information about the transfer switch, call

(800) 743-4115, between 8:00 AM and 5:00 PM CT.

Equipment Description

The transfer switch is designed to transfer the selected

loads found in normal residential installations to generator

power in the event of a utility power failure. The load is

connected either to utility power (normal) or home standby

power (generator). The transfer switch monitors utility and

generator voltages and will automatically connect to the

appropriate source of power.

Major components of the transfer switch are 2 pole

contactor switches, control circuit board, fused utility

terminals and interconnecting wiring.

The transfer switch is coil-operated from utility or generator

inputs and contains suitable electrical interlock switches to

eliminate the possibility of connecting the utility service to

the generator output.

The control board has active circuits sensing utility and

generator voltages. It creates a signal for the generator start-

up, switch transfer, retransfer when utility is restored and

generator cool down periods.

Not for reproduction

6 BRIGGSandSTRATTON.COM

Delivery Inspection

After opening the carton, carefully inspect the transfer

switch components for any damage that may have occurred

duringshipment.

If loss or damage is noted at time of delivery, have the

person(s) making delivery note all damage on the freight bill

and affix his signature under the consignor’s memo of loss

or damage. If loss or damage is noted after delivery, contact

the carrier for claim procedures. Missing or damaged parts

are not warranted.

Shipment contents

• Automatic transfer switch (1)

• Installation and operator’s manual (1)

To be supplied by installer:

• Connecting wire and conduit

• Various specialty tools/equipment

Essential Circuit Isolation

Essential electrical loads are loads that will be powered by

the home generator. Essential loads are grouped together

and wired into the transfer switch.

TO THE INSTALLER: Consult with home generator owner(s)

to discuss their selection of “Essential Circuits”.

Ensure that the total of the selected load circuits fed by this

transfer switch are within the generator’s rated capacity.

The following requirements apply to this type of

isolationsystem:

• The automatic transfer switch is installed after the main

distribution panel.

• The automatic transfer switch has a load rating of

50Amps. This is the maximum load rating of the total

essential load.

• All wiring must conform to national, state and

localcodes.

The illustration below depicts the system installation and

assumes the utility is supplying 120/240Volt, single-phase

electrical service.

To Utility Power

Watt-Hourrmeter

Main Distribution Panel

To Air Conditioner (240V)

To Other Circuits (120V)

To Range

To Water Heater

240V

To generator

120V To Microwave

120V To Bathroom

240V To Well Pump

120V To Sump Pump

Neutral

120V

To Furnace Blower

To Lights

To Refrigerator

120V To Freezer

Automatic Transfer Switch

(in normal position)

Not for reproduction

Mounting Guidelines

The model 01917 automatic transfer switch is enclosed in a

NEMA Type 1 enclosure suitable for indoor use only. Model

01918 is identical circuitry enclosed in a NEMA Type 3R

enclosure suitable for indoor/outdoor use.

Guidelines for mounting the switch enclosureinclude:

• Model 01918 automatic transfer switch must be

installed with minimum NEMA 3R hardware for

conduitconnections.

• Install the switch on a firm, sturdy supportingstructure.

• To prevent switch contact distortion, level and

plumb the enclosure. This can be done by placing

washers between the switch enclosure and the

mountingsurface.

• Never install the switch where any corrosive substance

might drip onto the enclosure.

• Protect the switch at all times against excessive

moisture, dust, dirt, lint, construction grit and

corrosivevapors.

A typical indoor transfer switch installation is depicted

below. Discuss layout suggestions/changes with the owner

before beginning the system installation process.

NOTICE Before drilling conduit entry holes, or any

other holes, cover and protect the switch and electronics

to prevent dirt and metal fragments from entering the

mechanical and electrical components. Failure to do so may

result in damage or malfunction of the switch.

NOTICE Use a vacuum to clean any dirt or metal

shavings inside the transfer switch. Do not use a blower or

compressed air to clean the inside of the transfer switch

because debris may become lodged in the electrical and

mechanical components causing damage or malfunction.

Power Wiring Interconnections

All wiring must be the proper size, properly supported and

protected by conduit, if applicable. All wiring should be done

per applicable federal, state and local codes, standards and

regulations. Obey wire type and torque specifications printed

on terminal blocks and neutral/ground connectors.

Complete the following connections between the transfer

switch, main distribution panel, utility power and generator.

Use installer-supplied 300VAC or greater wire that complies

with Table 310.16 in the National Electric Code. Apply the

necessary correction factors and wire size calculations.

1. Set generator’s system switch to OFF position.

2. Set generator’s circuit breaker to OFF (open) position

and remove 15 Amp fuse from system control panel.

3. Turn off utility power to the standby generator and

transfer switch.

4. Using installer supplied 300VAC or greater wire,

connect utility power supply leads from a 50 Amp

two pole breaker installed in main distribution

panel to transfer switch terminals marked “UTILITY

CONNECTION”. Ensure breaker is turned OFF.

5. Using installer supplied 300VAC or greater wire,

connect main distribution panel ground to transfer

switch “GND” bus.

6. Using installer supplied 300VAC or greater wire,

connect main distribution panel neutral to transfer

switch “NEUTRAL” terminal.

7. Using installer supplied 300VAC or greater wire,

connect power supply leads from generator

control panel to transfer switch terminals labeled

“GENERATORCONNECTION”.

Automatic

transfer

switch

Main

distribution

panel

WARNING Low voltage wire cannot be installed in

same conduit as power voltage wiring.

• Failure to follow above warning could cause personal

injury, damage and/or malfunction of equipment.

NOTICE Improper installation can cause damage to the

circuit boards and shorten their life. Installing circuit

boards in live circuits will damage the board and is not

covered by warranty. ALWAYS disconnect ALL sources of

power prior to servicing.

• Remove all power prior to installing this equipment.

Failure to do so could cause internal damage to the board

when making electrical connections.

• Turn generator to OFF position.

• Turn off utility power to the standby generator and

transfer switch.

WARNING Battery posts, terminals and related

accessories contain lead and lead compounds, chemicals

known to the State of California to cause cancer and

reproductive harm. Wash hands after handling.

Not for reproduction

8 BRIGGSandSTRATTON.COM

8. Using installer supplied 300VAC or greater wire,

connect Neutral from generator control panel to

transfer switch “NEUTRAL” terminal.

9. Using installer supplied 300VAC or greater wire,

connect “GND” from generator control panel to transfer

switch “GND” terminal.

10. Connect transfer switch “UTILITY 240 VAC” terminals

to generator’s “240 VAC” terminals using installer

supplied 300VAC or greater copper wire, minimum

#14AWG conductors via two-poleconnector supplied

with generator.

11 If generator is installed in an area regularly subjected

to temperatures below 40°F (4°C), select a 50 second

warm up time by removing jumper installed on JP2 on

transfer switch control board.

12. Connect essential circuit loads to appropriate circuit

breakers in transfer switch.

13. Tighten all wire connections/fasteners to torque values

specified on label inside enclosure.

• Torque generator connector plug screws to 7 in-lb

(7.9 Newton meter).

The illustration below shows a typical completed installation.

Your actual installation will vary.

System Test

With the generator system switch in AUTO, turn the

50Amp circuit breaker feeding the transfer switch to the

OFF position. After a few minutes the generator will start

and the transfer switch will transfer essential loads to

generatorpower.

To return to utility power, turn the 50Amp circuit breaker

feeding the transfer switch ON.

240

VAC

240VAC

E 1

L 1

Automatic Transfer Switch

Two Pole

Breaker

Utility

Connection

JP2

Generator

Connection

To Watt-

Hourmeter

Neutral

Bus

Neutral

Bus

Neutral

Bus

Ground

Bus

Ground

Bus

Main Distribution PanelB&S Generator

Not for reproduction

Operation

To select automatic transfer operation, do the following:

1. Set 50 Amp circuit breaker feeding the transfer switch

to “ON” position.

2. Install 15 Amp fuse in generator’s control panel.

3. Set generator’s circuit breaker to “ON” position.

4. Set generator’s system switch to “AUTO” position.

The system will now be in automatic operation mode.

NEMA 3R Enclosure Door

To open door, press the spring-load door lock to the right

and pull down on the door.

To close and latch door, push door closed against enclosure.

While in this position, push door upwards. This will cause

spring-load door lock to engage and latch door in place.

Enclosure door MUST be closed and latched at all times

except when system is being serviced.

Testing the Automatic Transfer Switch

Turn the 50 Amp utility disconnect circuit breaker in the

main distribution panel to the “OFF” position. The automatic

sequence will follow. To go back to utility power, turn the

50Amp utility disconnect circuit breaker “ON”.

Automatic Sequence

Utility Fail

Utility voltage sensor senses when utility voltage is below

70% of nominal. Engine start sequence is initiated after

6second time delay.

Engine Warm-Up

Time delay to allow for engine warm-up before transfer. Use

jumper on control board to select delay of 20 seconds or

50seconds.

Transfer

Transfer from utility to generator supply occurs after

generator voltage is above set levels. Minimum engine run

time is 5 minutes after transfer.

Utility Pickup

Voltage pickup level is 80 percent of nominal voltage.

Retransfer

Retransfer from generator to utility power is approximately

10 seconds after utility voltage supply is above pickup level

and minimum run time is completed.

Engine Cool Down

Engine will run for 60 seconds after retransfer.

Maintenance

The transfer switch is designed to be maintenance free under

normal usage. However, inspection and maintenance checks

should be made on a regular basis. Maintenance will consist

mainly of keeping the transfer switch clean.

Visual inspections should be done at least once a month.

Access to transfer switch must not be obstructed. Keep

3feet (92 cm) clearance around transfer switch. Check

for an accumulation of dirt, moisture and/or corrosion

on and around the enclosure, loose parts/hardware,

cracks and/or discoloration to insulation, and damaged or

discoloredcomponents.

Exercise the transfer switch at least once every three months

as described in Testing the Automatic Transfer Switch

unless a power outage occurs and home generator has gone

through an automatic sequence. Allow generator to run for at

least 30 minutes.

Contact a licensed electrical professional to inspect and clean

the inside of the enclosure and other components of your

home generator system at least once a year.

When Calling for Assistance

You must have the Model Number and Serial Number from

the unit ID label at hand if it is necessary to contact a local

service center regarding service or repair of this unit. Obtain

this information from the unit ID label located on or inside

the enclosure.

To contact Briggs & Stratton call (800) 743 4115, between

8:00 AM and 5:00 PM CT.

Installation Inspection

Before placing the system into service, inspect the entire

installation carefully.

Complete the ”Installation Checklist” as you make the

inspection. Ensure all items have been filled-in and all

signatures have been obtained. Instruct the owner to mail

the white copy to the address shown on the checklist.

Not for reproduction

10 BRIGGSandSTRATTON.COM

Troubleshooting

Problem Cause Correction

Au tomatic transfer switch does not

transfer to generator

1. Generator breaker open.

2. Generator voltage not acceptable.

1. Reset generator circuit breaker.

2. Refer to generator manual.

Au tomatic transfer switch does not

transfer to utility

1. Main distribution panel breaker open.

2. Utility voltage not acceptable.

1. Reset main distribution panel breaker.

2. Wait for utility voltage to return

tonormal.

Ge nerator is still running after switch

transfers to utility power

Engine cool down period. Engine should stop after 1 minute.

Ge nerator is still running after utility

power is restored

1. Minimum engine run time has

notelapsed.

2. Fuse(s) in transfer switch is defective.

1. Wait five minutes for transfer switch

to retransfer to utility power.

2. Check fuse(s) and replace

ifnecessary

Not for reproduction

Schematic Diagram

Not for reproduction

12 BRIGGSandSTRATTON.COM

Wiring Diagram

Not for reproduction

Product Specifications

Model 01917

Enclosure .................................................................. NEMA 1

Rated Maximum Load Current*

(at 25°C/77°F) ........................................................50 Amps

Rated AC Voltage .................................................... 250 Volts

Poles .................................................................................... 2

Frequency ................................................................50/60 Hz

Fault Current Rating ......... 5,000 RMS Symmetrical Amperes

Normal Operating Range .... -20°F (-28.8°C) to 104°F (40°C)

Weight ............................................................27 lbs. (12 kg)

* This transfer switch is certified in accordance with UL (Underwriters

Laboratories) 1008 (transfer switch equipment). Short circuit rating is

limited to the lowest capacity of any device installed.

Model 01918

Enclosure ................................................................ NEMA 3R

Rated Maximum Load Current*

(at 25°C/77°F) ........................................................50 Amps

Rated AC Voltage .................................................... 250 Volts

Poles .................................................................................... 2

Frequency ................................................................50/60 Hz

Fault Current Rating ......... 5,000 RMS Symmetrical Amperes

Normal Operating Range .... -20°F (-28.8°C) to 104°F (40°C)

Weight ............................................................30 lbs (14 kg).

Automatic Transfer Switch

Not for reproduction

14 BRIGGSandSTRATTON.COM

Not for reproduction

Generator Systems

Manual de instalación y del operario

50 Amperios

Interruptor de

transferencia automática

Not for reproduction

2 BRIGGSandSTRATTON.COM

Gracias por comprar este conectador automático de Briggs & Stratton® Power Products. Este producto está diseñado para

utilizarse con generadores de reserva domésticos específicos y puede no funcionar con generadores producidos por otros

fabricantes. Recurra a un electricista profesional cualificado para determinar la aplicabilidad de este equipo en generadores

fabricados por terceros. Si se utiliza y mantiene de acuerdo con las instrucciones de este manual, su sistema le proporcionará

muchos años de funcionamiento fiable.

Este manual contiene información de seguridad para que usted conozca los peligros y riesgos propios de este sistema y

cómo evitarlos. Se ha realizado el máximo esfuerzo para que la instalación resulte segura, sencilla y económica. Debido a que

cada instalación es única, es imposible conocer y recomendar todos los procedimientos y métodos posibles para efectuarla.

No conocemos todos los riesgos y/o resultados posibles de cada método o procedimiento existente. Es importante que lea

y comprenda perfectamente estas instrucciones antes de intentar instalar o utilizar este equipo. Guarde estas instrucciones

para futuras consultas.

Este el conectador requiere instalación profesional antes de utilizarse. Consulte las instrucciones sobre los procedimientos

de instalación en la sección Instalación del presente manual. Los conectador sólo deben ser instalados por electricistas con

licencia. Las instalaciones deben cumplir estrictamente la totalidad de los códigos, estándares y regulaciones federales,

estatales y locales vigentes. El instalador debe seguir las instrucciones detalladamente.

Ubicación

Nunca debe ir demasiado lejos para encontrar el soporte y servicio de Briggs & Stratton para su sistema. Consulte las

Páginas Amarillas. Existen múltiples distribuidores de servicio autorizados que ofrecen un servicio de calidad. También puede

comunicarse con el Servicio técnico por teléfono al (800) 743 4115 de 8:00 a. m. a 5:00 p. m. Hora del Centro, hora del

centro de los EE. UU; o haga clic en Buscar un distribuidor en BRIGGSandSTRATTON.COM para que aparezca una lista de

distribuidores autorizados.

Para futuras consultas

Llene la siguiente información y conserve su factura para facilitar la identificación de la unidad en caso de que surjan

problemas relacionados con la compra en el futuro.

Conectador automático

Número de modelo

Revisión

Número de serie

Fecha de compra

Not for reproduction

Tabla de contenido

Instrucciones importantes deseguridad ................4

Instalación ....................................5

Orientación al propietario.......................................5

Responsabilidades del distribuidor / técnicoinstalador................5

Pautas de montaje ............................................7

Interconexión de los cables de alimentación ........................7

Prueba del sistema............................................8

Funcionamiento.................................9

Mantenimiento ................................ 10

Resolución de problemas ......................... 10

Especificaciones del producto ...................... 11

Not for reproduction

4 BRIGGSandSTRATTON.COM

Guarde estas instrucciones

Instrucciones importantes

deseguridad

GUARDE ESTAS INSTRUCCIONES - Este manual contiene

instrucciones importantes que se deben seguir durante la

instalación y el mantenimiento del equipo.

Símbolos sobre la seguridad y significados

El símbolo de alerta de seguridad indica un posible

riesgo para su integridad física. Se utiliza una palabra de

señalización (PELIGRO, ADVERTENCIA o ATENCIÓN) junto

con el símbolo de alerta para designar un grado o nivel

de gravedad de riesgo. Se puede utilizar un símbolo de

seguridad para representar el tipo de riesgo. La palabra de

señalización AVISO se utiliza para hacer referencia a una

práctica no relacionada con una lesión física.

PELIGRO indica un riesgo que, de no evitarse, provocará

la muerte o lesiones de gravedad.

ADVERTENCIA indica un riesgo que, de no evitarse,

podría provocar la muerte o lesiones de gravedad.

ATENCIÓN indica un riesgo que, de no evitarse, podría

provocar lesiones leves o moderadas.

AVISO hace referencia a una práctica no relacionada con una

lesión física.

El fabricante no puede prever toda circunstancia que conlleve

un riesgo potencial. Por tanto, las advertencias de este

manual, así como las etiquetas y calcomanías adheridas a

la unidad, no incluyen todos los riesgos posibles. Si utiliza

un procedimiento, método de trabajo o técnica de uso no

recomendado específicamente por el fabricante, deberá

asegurarse de que es seguro tanto para usted como para

otras personas. También deberá asegurarse de que el

procedimiento, método de trabajo o técnica de uso que elija

no hace que el equipo sea inseguro.

Descarga eléctrica Lea el manual

AVISO

La instalación de este equipo debe cumplir

estrictamente la totalidad de los códigos, estándares y

regulaciones vigentes, por lo que sólo debe ser llevada a

cabo por un electricista cualificado.

ADVERTENCIA Determinados componentes en

este producto y los accesorios relacionados contienen

sustancias químicas declaradas cancerígenas, causantes

de malformaciones, y otros defectos congénitos por el

Estado de California. Lávese las manos después de

manipular estos elementos.

ADVERTENCIA Los cables de baja tensión no se

pueden instalar en el mismo conducto que los

cables de suministro de energía.

• Si no se respeta esta indicación pueden producirse

lesiones, daños y/o fallos de funcionamiento del equipo.

ADVERTENCIA Una conexión a tierra defectuosa del

equipo puede provocar la electrocución.

• No toque los cables pelados.

• No utilice el equipo con cables desgastados,

deshilachados o deteriorados de cualquier otra forma.

• No manipule los cables eléctricos si se encuentra en

una zona húmeda, está descalzo o tiene las manos o los

piesmojados.

• Si tiene que trabajar junto a una unidad en

funcionamiento, manténgase en una superficie aislada y

seca para reducir el riesgo de descarga eléctrica.

• No permita que personas no cualificadas o niños utilicen

o reparen el equipo.

• En caso de accidente provocado por una descarga

eléctrica, desconecte inmediatamente todos los

suministros de energía eléctrica y póngase en contacto

con las autoridades locales. Evite el contacto directo con

la víctima.

ADVERTENCIA El equipo contiene alta tensión que

puede provocar lesiones o la muerte.

• A pesar de la seguridad del diseño del sistema, si éste se

utiliza con imprudencia, ignorando su mantenimiento o

sin las debidas precauciones, se pueden producir lesiones

o incluso la muerte.

AVISO Un tratamiento inadecuado del equipo puede

estropearlo y acortar su vida útil.

• Utilice el equipo sólo para los usos previstos.

• En caso de dudas sobre su uso, diríjase al distribuidor o a

Briggs & Stratton Power Products.

• No exponga el equipo a un exceso de humedad, polvo,

suciedad o vapores corrosivos.

• Manténgase alerta en todo momento cuando utilice este

equipo. Nunca lo utilice ni manipule en condiciones de

fatiga física o mental.

• Si se calientan excesivamente los dispositivos conectados,

apáguelos y abra sus interruptores o quite sus fusibles.

Not for reproduction

Instalación

Realmente valoramos que nos haya elegido. Por este

motivo, se ha realizado un esfuerzo importante para que

la instalación resulte segura, sencilla y económica. Debido

a que cada instalación es única, es imposible conocer y

recomendar todos los procedimientos y métodos posibles

para efectuarla. Tampoco conocemos todos los riesgos y/o

resultados posibles de cada método o procedimiento.

Por tanto, la instalación del sistema sólo puede ser

llevada a cabo por un electricista con licencia vigente.

Las instalaciones deben cumplir estrictamente la

totalidad de los códigos, estándares de la industria y

regulacionesvigentes.

Su equipo se suministra con este “Manual de instalación

y del operario” combinado. Se trata de un documento

importante que el propietario debe conservar después de

haber terminado la instalación.

Se ha realizado el máximo esfuerzo para reunir en este

manual la información más precisa y actualizada. No

obstante, el fabricante se reserva el derecho de modificar,

alterar o mejorar de cualquier otra forma el sistema en

cualquier momento y sin previo aviso.

Responsabilidades del propietario

Para tomar decisiones bien fundadas y comunicarse

eficazmente con el técnico instalador, lea y comprenda la

sección Orientación al propietario antes de contratar o

iniciar la instalación del equipo.

Para solicitar la instalación, póngase en contacto con la

tienda en la que adquirió el equipo, con su distribuidor o con

la compañía eléctrica.

La garantía del equipo quedará ANULADA a menos

que electricistas profesionales con licencia instalen

elsistema.

Orientación al propietario

Las ilustraciones incluidas corresponden a circunstancias

habituales y tienen por objeto familiarizarle con las opciones

de instalación del sistema.

La normativa local, la apariencia y las distancias son los

aspectos que deberán tenerse en cuenta al negociar la

instalación con un profesional. Al aumentar la distancia

desde el servicio eléctrico, se deberá prever una

compensación en cables y otros materiales necesarios

para cumplir la normativa local vigente y evitar caídas de

tensióneléctrica.

Estos factores tendrán un efecto directo en el precio total de

la instalación del equipo.

El instalador deberá comprobar la normativa local Y obtener

los permisos correspondientes antes de instalar elsistema.

• Lea y siga las instrucciones que se indican en

estemanual.

• Siga un plan regular de cuidado y uso del equipo, como

se indica en este manual.

Responsabilidades del distribuidor /

técnicoinstalador

• Lea y respete las normas de seguridad.

• Lea y siga las instrucciones que se indican en

estemanual.

• Es posible que el instalador tenga que proporcionar

contactores nominales adecuados con base en las

cargas que van a controlarse.

• Consulte la normativa vigente en caso de dudas sobre

la instalación.

• Asegúrese de que las cargas seleccionadas no

sobrecargan el generador.

Si necesita más información sobre el conectador, llame al

(800) 743-743-4115, de 08:00 a 17:00 CT.

Descripción del equipo

El conectador está diseñado para transferir las cargas

seleccionadas de una instalación residencial normal

al suministro del generador en caso de un fallo en el

suministro de alimentación de la red pública. La carga

se conecta al suministro de servicio general (normal)

o al suministro doméstico de reserva (generador). El

conectador monitoriza las tensiones de la red pública y del

generador y conecta automáticamente la carga a la fuente de

alimentación apropiada.

Los componentes principales del conectador son los

interruptores de contacto bipolares, la tarjeta de circuito

impreso de control, los terminales con fusibles de tensión de

la red pública y el cableado de interconexión.

El conectador es accionado por una bobina alimentada

desde entradas de la red pública o del generador y tiene

interruptores de enclavamiento eléctricos, adecuados para

eliminar la posibilidad de conectar la red pública a la salida

del generador. Sus valores nominales son suficientes para

conectar la potencia del generador a la residencia.

La tarjeta de circuito impreso del módulo de control tiene

circuitos activos que detectan las tensiones de la red pública

y del generador. Genera una señal para el arranque del

generador, conectador, retransferencia cuando se restablece

la tensión en la red pública y períodos de enfriamiento

delgenerador.

Not for reproduction

6 BRIGGSandSTRATTON.COM

Inspección en el momento de la entrega

Después de abrir la caja de cartón, con cuidado inspeccione

el contenido para detectar cualquier daño que pudiera haber

ocurrido durante el envío.

Si detecta faltas o daños en el momento de la entrega,

solicite a la persona que realiza la entrega que anote

todos los daños en Ia nota de entrega y que la firme bajo

el área de pérdidas y daños del remitente. Si se detectan

faltas o daños después de la entrega, póngase en contacto

con el transportista para solicitar información sobre el

procedimiento de reclamación. La garantía no cubre las

partes faltantes o dañadas.

Contenido del paquete

• Conmutador de transferencia de energía automático (1)

• Manual de instalación y operario (1)

No incluye:

• Cable y conducto de conexión.

• Herramientas/equipos especiales diversos

Aislamiento de los circuitos fundamentales

Las cargas eléctricas fundamentales son aquellas que

serán alimentadas mediante el sistema de generador. Las

cargas fundamentales se agrupan y se conectan dentro del

compartimiento del conmutador de transferencia automático.

AL INSTALADOR: Consulte con el propietario del

sistema de generador para analizar la “Selección de los

circuitosfundamentales”.

Asegúrese de que el total de los circuitos de carga

seleccionados para ser alimentados por este conmutador de

transferencia se encuentre dentro de la capacidad nominal

del generador.

Los siguientes requisitos se aplican a este tipo de sistema

deaislamiento:

• El conmutador de transferencia automático se instala

después de instalar el panel de distribución principal.

• El conmutador de transferencia automático tiene un

valor nominal de carga de 50 Amperios. Este es el valor

nominal máximo para las cargas fundamentals totales.

• Todas las conexiones de cableado deben cumplir con

lo establecido en el nacional, todos los códigos locales

yestatales.

La ilustración muestra el sistema de generador y supone

que la compañía proveedora de electricidad entrega

120/240Voltios, con corriente monofásica.

A la energía de la compañía proveedora de electricidad

Vatímetro

Panel de distribución principal

Al acondicionador de aire (240V)

A otros circuitos (120V)

A la cocina

Al calentador de agua

240V

A la generador

120V al horno de microondas

120 V al cuarto de baño

240V A la bomba de pozo

120V A la bomba de sumidero

Neutro

120V

Al soplador de caldera

A las luces

Al refrigerador

120V al freezer

Conmutador de transferencia

automático (en posición normal)

Not for reproduction

La page charge ...

Simplicity 01917-0 Manuel utilisateur

Marque: Simplicity

Modèle: 01917-0

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Simplicity 01917-0 User manual
español: Simplicity 01917-0 Manual de usuario

Simplicity 01917-0 Manuel utilisateur

Simplicity 01917-0 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents