Samsung HL-T5689S Manuel utilisateur

Register your product at www.samsung.com/global/register

Record your Model and Serial number here for future reference.

▪ Model _______________ ▪ Serial No. _______________

Owner’s Instructions

HL-T5089S

HL-T5689S

HL-T6189S

DLP TV

BP68-00628B-00Eng_1.indd 3 2007-03-02 ｿﾀﾈﾄ 4:21:07

English - 2

A Guide to Digital TV

● What is Digital Television?

Digital television (DTV) is a new way of transmitting high quality video and audio to your TV set. Using DTV, broadcasters can

transmit high definition TV (HDTV) images, Dolby digital surround audio, and new services such as multicasting (transmitting

more than one program on the same TV channel) and datacasting. Several of these services can be combined into a single digital

broadcast.

Digital Television Services

● Digital Picture Quality

DTV programs are transmitted in two different formats. The first is Standard Definition Television (SDTV) and the second is High

Definition Television (HDTV).

●

SDTV program formats include 480-line interlaced (480i) and 480-line progressive (480p) video. 480i programs are essentially

a digital version of our current analog TV programs, while the 480p format offers improved image detail over 480i. Some 480p

programs are broadcast in widescreen and are comparable to progressive-scan DVD movies in image quality.

●

HDTV program formats include 1080-line interlaced (1080i) and 720-line progressive (720p). Both HDTV formats are always

broadcast in widescreen, and offer much higher picture quality than SDTV.

●

Dolby Surround Sound

With DTV, you can listen to a variety of Dolby digital audio formats from Dolby Surround 2.0 to Dolby Digital 5.1 surround, using

your home audio system. Many HDTV programs are now broadcast with DD 5.1 soundtracks.

FCC Statements

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference

that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate

the equipment.

To comply with the FCC RF exposure compliance requirements, this device and its antenna must not be co-located or operated in

conjunction with any other antenna or transmitter.

BP68-00628B-00Eng_1.indd 2 2007-03-02 ｿﾀﾈﾄ 4:21:07

English - 3

Q&A

1. Is the antenna I use for existing TV reception good enough for DTV?

Over-the-air (OTA) digital TV broadcasting uses the same channels as analog TV and works well with many existing TV antennas.

However, DTV broadcast channel assignments are different than analog channels. You should find out whether your local DTV

broadcasts are on VHF (channels 2-13) or UHF (channels 14-69) to see if you need a different antenna.

If your DTV channels are on UHF and you already get good UHF reception, your present antenna may work fine. The same holds

true for VHF DTV reception. Note that in some markets, both VHF and UHF channels are used for DTV broadcasts.

You can find out the latest DTV channel assignments for your area by browsing selected Internet web sites such as www.titantv.

com, www.10000watts.com, and www.fcc.gov.

2. How difficult is it to receive DTV signals indoors?

This depends on whether your local DTV stations are running full power or not and how close your location is to the transmission

tower. DTV receivers do not require as much signal as analog TV receivers to produce high-quality images and sound.

Once the DTV signal level exceeds a certain threshold at the receiver, the digital video and audio data is decoded at the same

quality it was originally encoded for broadcast.

This is a big advantage for DTV over analog TV - there is no noise, ghosting, static, or scratchy audio.

3. How can I connect an antenna in my townhouse, co-operative apartment, condominium, or

apartment?

The Federal Communications Commission’s OTARD Rule (part of the Telecommunications Act of 1996) allows residents of

condominiums, townhouse, or members of neighborhood associations to put up outside antennas for reception of broadcast TV

signals as long as those antennas are not located in common areas and are no more than 12’ in height.

Residents of rental units (apartments, etc.) are not covered by the OTARD rules and will have to use indoor antennas to receive

DTV broadcasts. It is possible that the landlord of an apartment complex can provide broadcast DTV signals via a master TV

antenna system to each apartment.

4. Can I connect my DTV set-top receiver to my cable TV service?

Cable TV systems use a different method for transmitting digital TV programs that is currently incompatible with broadcast DTV set-

top receivers. So you will still need to use an outdoor or indoor antenna to receive OTA broadcast DTV programs.

The good news is that you won’t have to pay a monthly or per-program charge to watch OTA DTV and HDTV programs. They’re

free, unlike subscription satellite TV or premium cable TV. All you need is an antenna and a DTV set-top receiver to enjoy clear,

sharp widescreen images and high-quality audio.

BP68-00628B-00Eng_1.indd 3 2007-03-02 ｿﾀﾈﾄ 4:21:07

English - 4

General Information

■

Viewing Position .......................................................5

■

List of Features .........................................................5

■

Checking Parts .........................................................6

■

Viewing the Control Panel ........................................6

■

Viewing the Connection Panel .................................8

■

Remote Control ........................................................9

■

Installing Batteries in the Remote Control ..............10

Connections

■

Connecting VHF and UHF Antennas ......................10

■

Connecting Cable TV ............................................. 11

■

Connecting a VCR ..................................................12

■

Connecting a Camcorder .......................................13

■

Connecting a DVD Player/Set-Top Box ..................13

■

Connecting a DVD Player/Set-Top Box via HDMI .. 14

■

Connecting a DVD Player/Set-Top Box via DVI .....14

■

Connecting a Digital Audio System ........................ 15

■

Connecting an Ampliﬁer/DVD Home Theater .........15

■

Connecting a PC ....................................................16

Operation

■

Turning the TV On and Off ..................................... 16

■

Plug & Play Feature ...............................................17

■

Changing Channels ................................................19

■

Adjusting the Volume ..............................................19

■

Viewing the Display ................................................20

■

Viewing the Menus .................................................20

■

Using the TOOLS Button ........................................20

■

Memorizing the Channels .......................................21

■

Setting Up Your Remote Control ............................22

■

To Select the Source ..............................................27

■

To Edit the Input Source Name ..............................27

Picture Control

■

Using Automatic Picture Settings ........................... 28

■

Making Detail Settings on the Picture ....................29

■

Changing the Screen Size ......................................30

■

Digital Noise Reduction ..........................................31

■

Setting the Active Color ..........................................31

■

DNIe (Digital Natural Image engine) ......................32

■

Setting the Color Gamut .........................................32

■

Adjusting the Screen Position ................................33

■

Resetting the Picture Settings ................................33

■

Viewing Picture-in-Picture ...................................... 34

■

Freezing the Current Picture .................................. 35

Sound Control

■

Using the Automatic Sound Settings ......................36

■

Customizing the Sound ..........................................36

■

Setting the TruSurround XT ....................................37

■

Choosing a Multi-Channel Sound (MTS) Track -

Digital .....................................................................38

■

Choosing a Multi-Channel Sound (MTS) Track -

Analog ....................................................................38

■

Automatic Volume Control ......................................39

■

Selecting the Internal Mute .....................................39

■

Resetting the Sound Settings .................................40

Channel Control

■

Clearing Scrambled Channels

- Digital ................... 40

■

Managing Channels ...............................................41

■

Fine Tuning Analog Channels - Analog .................. 46

■

Checking the Digital-Signal Strength - Digital ........47

■

LNA (Low Noise Ampliﬁer) ......................................47

Function Description

■

Selecting a Menu Language ...................................48

■

Setting the Time .....................................................48

■

Viewing Closed Captions (On-Screen Text

Messages) - Digital .................................................51

■

Viewing Closed Captions (On-Screen Text

Messages) - Analog ................................................52

■

Using the Game Mode ...........................................53

■

Using the 3D/Dual-View Function ..........................53

■

Using the V-Chip ....................................................54

■

Menu Transparency Level ......................................59

■

Setting the HDMI Black Level .................................59

■

Setting the Film Mode - Analog .............................. 60

■

Setting the Light Effect ...........................................60

■

Setting the Blue Screen Mode ................................61

■

Adjusting the Melody Sound ...................................61

■

Upgrading the Software ..........................................62

■

Setting the Function Help .......................................62

PC Display

■

Using Your TV as a Computer (PC) Display .......... 63

■

Display Modes ........................................................ 64

■

Setting up the TV with your PC ..............................65

■

Changing the Picture Size (PC Mode) ...................67

■

Setting the Home Theater PC ................................67

Bluetooth

■

What is Bluetooth? .................................................68

■

Bluetooth Communication and Setting Up PIN ......68

■

Connecting a Bluetooth Headset (Optional) ........... 69

■

Capturing and Printing the Screen .........................69

Wiselink

■

Using the WISELINK Function ............................... 70

■

Using the WISELINK Mode ....................................71

■

Using the Photo (JPEG) List ..................................72

■

Using the Music (MP3) List ....................................79

About Anynet+

■

What is Anynet+? ...................................................81

■

Connecting Anynet+ Devices .................................81

■

Setting Up Anynet+ .................................................82

■

Scanning and Switching between Anynet+ Devices

.. 82

■

Recording ...............................................................83

■

Listening through a Receiver (Home theater)

....84

■

Check Points before Requesting Service ............... 84

Appendix

■

Identifying Problems ............................................... 85

■

Cleaning and Maintaining Your TV ......................... 86

■

Using Your TV in Another Country .......................... 86

■

Technical Speciﬁcations .........................................87

Contents

Symbols

Press

One-Touch

Button

➢

Note

BP68-00628B-01Eng_1.indd 4 2007-03-09 ｿﾀﾀ・9:39:44

English - 5

General Information

Viewing Position

To optimize your viewing comfort, please follow the guidelines below for viewing distance.

If viewing for an extended period of time, sit as far back from the screen as possible.

➢

When installing the product, make sure to keep it away

from the wall (more than 10cm / 4inches) for ventilation

purposes. Poor ventilation may cause an increase in

the internal temperature of the product, resulting in a

shortened component life and degraded performance.

< Top view> < Side view>

50˝ screen :

At least 5.9 feet

List of Features

Your TV is designed and engineered using the latest technology. It is a full-featured, high-performance unit that exceeds

industry standards. In addition, it has these special features:

● Easy-to-operate remote control

● Dynamic menus and Navigating menus by using the menu map

● Easy-to-use on-screen menu system you can access from the side panel or remote control

● Automatic timer to turn the TV on and off at any time you choose

● Adjustable picture and sound settings and the ability to memorize your favorite settings

● Automatic channel tuning for up to 181 channels

● A special filter to reduce or eliminate reception problems

● Fine tuning control for the sharpest picture possible

● A built-in multi-channel sound decoder for stereo and bilingual listening

● Built-in, dual channel speakers

● A special sleep timer

● Widescreen TV with adjustable image size

● Life-like clear images provided by DNle technology

● My Color Control mode to correspond with your color preference

● Digital Input jack

● Digital Audio Output (OPTICAL) jack

● Theater Game Mode

● Easy-to-use channel list menu.

● AV network system (Anynet+) that enables you to easily control Samsung audio-video(AV) devices from this TV.

● TV supports wireless connection to selected Bluetooth stereo headsets and photo printers.

● WISELINK enables you to view and play photo (JPEG) and audio files (MP3) through the TV’s WISELINK jack.

56˝ screen :

At least 6.6 feet

61˝ screen :

At least 7.2 feet

50˝ screen :

At least 5.9 feet

56˝ screen :

At least 6.6 feet

61˝ screen :

At least 7.2 feet

BP68-00628B-00Eng_1.indd 5 2007-03-02 ｿﾀﾈﾄ 4:21:08

English - 6

Viewing the Control Panel

Buttons on the Lower-Right Part of the Panel

The buttons on the lower-right panel control your TV’s basic features, including the on-screen menu.

To use the more advanced features, you must use the remote control.

Checking Parts

Owner’s Instructions Remote Control

(BP59-00126A)/

AAA Batteries

Warranty Card/

Registration Card/

Safety Guide Manual/

Quick Guide Manual

Power Cord

(3903-000144)

Cloth-Clean

➢

The product color and shape may vary depending on the model.

Continued...

Sold Separately

S-Video Cable Video Cable Antenna Cable

Component Cables

Audio Cables

PC Cable PC Audio Cable HDMI/DVI Cable HDMI Cable Optical Cable

1Stereo/2RCA Cable

BP68-00628B-00Eng_1.indd 6 2007-03-02 ｿﾀﾈﾄ 4:21:12

English - 7

1

SOURCE

Toggles between all the available input sources

(TV, AV1, AV2, S-Video1, S-Video2, Component1,

Component2, PC, HDMI1, HDMI2, HDMI3/DVI, or

USB).

2

MENU

Press to see an on-screen menu of your TV’s features.

3

+ VOL –

Press to increase or decrease the volume.

In the on-screen menu, use the + VOL – buttons as

you would use the ◄ and ► buttons on the remote

control.

4

CH

Press to change channels.

In the on-screen menu, use the CH buttons as

you would use the ▲ and ▼ buttons on the remote

control.

5

(ENTER)

Press to confirm a selection.

6

POWER

Press to turn the TV on and off.

7

Remote Control Sensor

Aim the remote control towards this spot on the TV.

8

Indicator Lights

Blinks and turns off when the power is on and lights up

in stand-by mode.

Indicator Light Key

( : On, : Blinking, : Off)

STAND BY/TEMP TIMER LED Indication

Standby state.

The picture will automatically appear in about 15 seconds.

Auto Timer ON/OFF has been set and the set will automatically be turned on in about 15 seconds.

A cooling fan inside the set is not operating normally.

Check if the ventilation hole on the side of the set is blocked, because if the inner temperature is too

high, the power will shut off.

LED may be defective. Please contact a certified technician.

➢

● It takes about 30 seconds for the TV to warm up, so normal brightness may not appear immediately.

● The TV has a fan to keep the inside optic chassis from overheating. You’ll occasionally hear it working.

➢

● You can use the channel selection buttons to switch on the TV when it is in standby mode depending on the model.

● When using the on-screen menu the volume adjustment and channel selection buttons have the same function as the

▲/▼/◄/► buttons on the remote control.

● If the remote control no longer works or you have lost it, you can use controls on the panel of the TV.

BP68-00628B-00Eng_1.indd 7 2007-03-02 ｿﾀﾈﾄ 4:21:14

English - 8

Viewing the Connection Panel

Side Panel Jacks

Use the side panel jacks to connect A/V components that will be connected continuously, such as VCR or DVD players.

For more information on connecting equipment, see pages 10~16.

Continued...

➢

The product color and shape may vary depending on the model.

1

ANT 1 IN (CABLE)/ANT 2 IN (AIR)

75Ω Coaxial connector for Air/Cable Network.

2

HDMI IN 1, HDMI IN 2

Connect to the HDMI jack of a device with HDMI output.

3

HDMI3/DVI IN

Connect to the HDMI jack of a device with HDMI output.

This input can also be used as a DVI connection with

separate analog audio inputs. An optional HDMI/DVI cable

will be necessary to make this connection.

When using an optional HDMI/DVI adapter, the DVI analog

audio inputs on your TV allow you to receive left and right

audio from your DVI device. (Not compatible with PC)

4

RS232C

For service only.

5

DIGITAL AUDIO OUT (OPTICAL)

Connect to a Digital Audio component.

6

DVI IN (AUDIO-L/R)

Connect to the DVI audio output jack of an external device.

7

S-VIDEO (AV IN 1, 2)

Video input for external devices with an S-Video output, such

as a Camcorder or VCR.

8

3D SYNC OUT

Connect to 3D IR Emitter.

9

VIDEO/AUDIO OUT-L/R (AV OUT)

Video/Audio outputs for external devices.

Video output is not avaiable RF(Digital)/Component/PC/

HDMI.

0

WISELINK

Connect an USB mass storage device to view photo files

(JPEG) and play audio files (MP3).

!

VIDEO/AUDIO-L/R (AV IN 1, 2)

Video input for external devices, such as a Camcorder or

VCR.

@

PC IN

Connect to the video output jack on your PC.

#

PC AUDIO IN

Connect to the audio output jack on your PC.

$

COMPONENT IN 1, 2

Video (Y/PB/PR) and audio (L-AUDIO-R) component inputs.

%

POWER IN

Connect the supplied power cord.

BP68-00628B-00Eng_1.indd 8 2007-03-02 ｿﾀﾈﾄ 4:21:14

English - 9

Remote Control

You can use the remote control up to a distance of about 23 feet from the TV. When using the remote, always point it directly

at the TV. You can also use your remote control to operate your VCR, Cable box, DVD player, or Set-Top Box.

1

POWER

Turns the TV on and off.

2

Numeric Buttons

Press to directly select a channel.

3

–

Press to select additional channels

being broadcast by the same station.

For example, to select channel “54-3”,

press “54”, then press “–” and “3”.

4

CH LIST

Used to display Channel Lists on the

screen.

5

ANTENNA

Press to select “Air” or “Cable”.

6

VOL +, VOL –

Press to increase or decrease the

volume.

7

MUTE

Press to temporarily cut off the sound.

8

MENU

Displays the main on-screen menu.

9

RETURN

Returns to the previous menu.

0

S.MODE

Press to select the sound mode.

!

P.MODE

Press to select the picture mode.

@

FAV.CH

Press to switch to your favorite

channels.

#

GAME

Press to select the Game mode except

for the TV mode.

$

CAPTION

Controls the caption decoder.

%

3D

Press to select the 3D/Dual-View

mode.

^

SET

Sets the remote to control your TV,

VCR, Cable, DVD, or Set-Top Box.

&

TV, DVD, STB, CABLE, VCR

Press to operate your TV, DVD, STB,

CABLE (box), or VCR.

*

SOURCE

Press to display all of the available

video sources.

(

Press to activate the backlight of the

VOL, CH and the active source button

(TV, DVD, CABLE, STB, VCR) on the

remote control.

)

PRE-CH

Tunes to the previous channel.

a

WISELINK

This function enables you to view and

play photo (JPEG) and audio files

(MP3) from an external device. (See

page 72 (JPEG), 79 (MP3))

b

REC

Use to make a recording.

c

VCR/DVD Functions

- Rewind

- Stop

- Play/Pause

- Fast Forward

d

CH , CH

Press to change channels.

e

EXIT

Press to exit from the menu.

f

UP▲/DOWN▼/LEFT◄/RIGHT►/

ENTER

Use to select on-screen menu items

and change menu values.

g

INFO

Press to display information on the TV

screen.

h

TOOLS

Use to quickly select frequently used

functions.

Anynet+

Runs the Anynet+ view functions and

sets up Anynet+ devices.

i

STILL

Press to stop the action during a

particular scene.

Press again to resume normal video.

j

P.SIZE

Press to change the screen size.

k

Color buttons

Press to add or delete channels and to

store channels to the favorite channel

list in the Channel List menu.

(Refer to pages 41~46)

l

CH /

Displays the available channels in

sequence. (These buttons change

channels in the PIP window only.)

m

PIP

Picture-in Picture ON/OFF.

n

MTS

Press to choose stereo, mono or

Separate Audio Program (SAP

broadcast).

o

RESET

When your remote control does not

work, change the batteries and press

the RESET button for 2-3 seconds

before use.

➢

The performance of the remote control may be affected by bright light.

➢

This is a special remote control for the visually impaired persons, and has Braille points on the POWER, Channel, Volume, STOP,

and PLAY/PAUSE buttons.

BP68-00628B-01Eng_1.indd 9 2007-03-09 ｿﾀﾀ・9:40:49

English - 10

Installing Batteries in the Remote Control

1 Lift the cover at the back of the remote control upward as shown in the figure.

2 Install two AAA size batteries.

➢

● Make sure to match the “+” and “–” ends of the batteries with the diagram inside the

compartment.

● Do not mix battery types, i.e. alkaline and manganese.

3 Close the cover as shown in the figure.

➢

Remove the batteries and store them in a cool and dry place if you won’t be using the remote

control for a long time. The remote control can be used up to about 23 feet from the TV.

(Assuming typical TV usage, the batteries last for about one year.)

➢

If the remote control doesn’t work! Check the following

1. Is the TV power on?

2. Are the plus and minus ends of the batteries reversed?

3. Are the batteries drained?

4. Is there a power cut, or is the power cord unplugged?

5. Is there a special fluorescent light or a neon sign nearby?

Connections

Connecting VHF and UHF Antennas

If your antenna has a set of leads that look like this, see “Antennas with 300 Ω Flat Twin

Leads” below.

If your antenna has one lead that looks like this, see “Antennas with 75 Ω Round Leads”.

If you have two antennas, see “Separate VHF and UHF Antennas”.

Antennas with 300 Ω Flat Twin Leads

If you are using an off-air antenna (such as a roof antenna or “rabbit ears”) that has 300 Ω twin flat leads, follow the

directions below.

1 Place the wires from the twin leads under the screws on a 300-75 Ω adapter (not supplied).

Use a screwdriver to tighten the screws.

2 Plug the adaptor into the ANT 1 IN (CABLE) or ANT 2 IN (AIR) terminal on the side of the TV.

Antennas with 75 Ω Round Leads

1 Plug the antenna lead into the ANT 1 IN (CABLE) or ANT 2 IN (AIR) terminal on the side of the

TV.

Separate VHF and UHF Antennas

If you have two separate antennas for your TV (one VHF and one UHF), you must combine the two antenna signals before

connecting the antennas to the TV. This procedure requires an optional combiner-adaptor (available at most electronics

shops).

1 Connect both antenna leads to the combiner.

2 Plug the combiner into the ANT 1 IN (CABLE) or ANT 2 IN (AIR) terminal on the bottom of the

side panel.

BP68-00628B-00Eng_1.indd 10 2007-03-02 ｿﾀﾈﾄ 4:21:18

English - 11

Connecting Cable TV

To connect to a cable TV system, follow the instructions below.

Cable without a Cable Box

1 Plug the incoming cable into the ANT 1 IN (CABLE) terminal on the side of the TV.

➢

Because this TV is cable-ready, you do not need a cable box to view unscrambled cable

channels.

Connecting to a Cable Box that Descrambles All Channels

1 Find the cable that is connected to the ANT OUT terminal on your cable box.

➢

This terminal might be labeled “ANT OUT”, “VHF OUT” or simply, “OUT”.

2 Connect the other end of this cable to the ANT 1 IN (CABLE) terminal on the side of the TV.

Connecting to a Cable Box that Descrambles Some Channels

If your cable box descrambles only some channels (such as premium channels), follow the instructions below. You will need

a two-way splitter, an RF (A/B) switch, and four lengths of Antenna cable. (These items are available at most electronics

stores.)

1 Find and disconnect the cable that is connected

to the ANT IN terminal on your cable box.

➢

This terminal might be labeled “ANT IN”, “VHF

IN” or simply, “IN”.

2 Connect this cable to a two-way splitter.

3 Connect an Antenna cable between an OUTPUT

terminal on the splitter and the IN terminal on the

cable box.

4 Connect an Antenna cable between the ANT OUT

terminal on the cable box and the B–IN terminal

on the RF(A/B) switch.

5 Connect another cable between the other OUT

terminal on the splitter and the A–IN terminal on

the RF (A/B) switch.

6 Connect the last Antenna cable between the OUT

terminal on the RF (A/B) switch and the ANT 1 IN

(CABLE) terminal on the side of the TV.

After you have made this connection, set the A/B switch to the “A” position for normal viewing. Set the A/B switch to the “B” position to

view scrambled channels. (When you set the A/B switch to “B”, you will need to tune your TV to the cable box’s output channel, which

is usually channel 3 or 4.)

Splitter

Incoming

cable

Splitter

Cable Box

Incoming

cable

Splitter

Cable Box

RF (A/B)

Switch

Incoming

cable

Splitter

Cable Box

Incoming

cable

RF (A/B)

Switch

Incoming

cable

Splitter

Cable Box

RF (A/B)

Switch

TV Side

ANT OUT

ANT IN

BP68-00628B-00Eng_1.indd 11 2007-03-02 ｿﾀﾈﾄ 4:21:21

English - 12

Connecting a VCR

Video Connection

These instructions assume that you have already connected your TV to an antenna or a cable TV system (according to the

instructions on pages 10~11). Skip step 1 if you have not yet connected to an antenna or a cable system.

1 Unplug the cable or antenna from

the side of the TV.

2 Connect the cable or antenna to

the ANT IN terminal on the side of

the VCR.

3 Connect an Antenna Cable

between the ANT OUT terminal

on the VCR and the ANT 1 IN

(CABLE) or ANT 2 IN (AIR)

terminal on the TV.

4 Connect a Video Cable between

the AV IN 1 [VIDEO] (or AV IN 2

[VIDEO]) jack on the TV and the

VIDEO OUT jack on the VCR.

5 Connect Audio Cables between the

AV IN 1 [L-AUDIO-R] (or AV IN 2

[L-AUDIO-R]) jacks on the TV and

the AUDIO OUT jacks on the VCR.

➢

If you have a “mono”

(non-stereo) VCR, use a

Y-connector (not supplied) to

hook up to the right and left audio input jacks of the TV. If your VCR is stereo, you must connect two cables.

➢

Each VCR has a different side panel configuration.

➢

When connecting a VCR, match the color of the connection terminal to the cable.

S-Video Connection

Your Samsung TV can be connected to the S-Video jack of a VCR.

(This connection delivers a better picture when compared to the regular video connection above.)

1 To begin, follow steps 1–3 in the

previous section to connect the

antenna or cable to your VCR and

your TV.

2 Connect an S-Video Cable

between the AV IN 1 [S-VIDEO] (or

AV IN 2 [S-VIDEO]) jack on the TV

and the S-VIDEO OUT jack on the

VCR.

3 Connect Audio Cables between the

AV IN 1 [L-AUDIO-R] (or AV IN 2

[L-AUDIO-R]) jacks on the TV and

the AUDIO OUT jacks on the VCR.

➢

Each VCR has a different side panel configuration.

➢

When connecting a VCR, match the color of the connection terminal to the cable.

➢

Some games may be displayed with a cut off picture when the TV is connected to a game player.

2

TV Side Panel

VCR

Audio Cable(Not supplied)5

Video Cable(Not supplied)4

Antenna cable(Not supplied)3

TV Side Panel

VCR

Audio Cable

(Not supplied)

3

S-Video Cable(Not supplied)2

Antenna cable(Not supplied)1

1

BP68-00628B-00Eng_1.indd 12 2007-03-02 ｿﾀﾈﾄ 4:21:24

English - 13

Connecting a Camcorder

The side panel jacks on your TV make it easy to connect a camcorder to your TV.

They allow you to view the camcorder tapes without using a VCR

1 Connect a Video Cable or S-Video

Cable between the AV IN 1 [VIDEO]

or [S-VIDEO] (or AV IN 2 [VIDEO] or

[S-VIDEO]) jack on the TV and the

VIDEO OUT or S-VIDEO OUT jack

on the camcorder.

2 Connect Audio Cables between

the AV IN 1 [L-AUDIO-R] (or AV IN

2 [L-AUDIO-R]) jacks on the TV

and the AUDIO OUT jacks on the

camcorder.

➢

Each Camcorder has a different side panel configuration.

➢

When connecting a Camcorder, match the color of the connection terminal to the cable.

Connecting a DVD Player/Set-Top Box

The side jacks on your TV make it easy to connect a DVD player/Set-Top Box

1 Connect Component Cables

between the COMPONENT IN 1

[Y, PB, PR] (or COMPONENT IN

2 [Y, PB, PR]) jacks on the TV and

the COMPONENT OUT [Y, PB, PR]

jacks on the DVD Player/Set-Top

Box.

2 Connect Audio Cables between the

COMPONENT IN 1 [L-AUDIO-R]

(or COMPONENT IN 2 [L-AUDIO-

R]) jacks on the TV and the AUDIO

OUT jacks on the DVD player/Set-

Top Box.

➢

Component video separates the video into Y Luminance (brightness), PB (Blue) and PR (Red) for enhanced video quality.

Be sure to match the component video and audio connections.

For example, if connecting the video cable to COMPONENT IN, connect the audio cable to COMPONENT IN also.

➢

Each DVD Player/Set-Top box has a different side panel configuration.

➢

When connecting a DVD Player/Set-Top box, match the color of the connection terminal to the cable.

TV Side Panel

Camcorder

S-Video Cable(Not supplied)

1

Video Cable(Not supplied)

1

Audio Cable(Not supplied)

2

or

TV Side Panel

DVD Player/Set-Top Box

Audio Cable(Not supplied)

2

Component Cable(Not supplied)

1

BP68-00628B-00Eng_1.indd 13 2007-03-02 ｿﾀﾈﾄ 4:21:28

English - 14

Connecting a DVD Player/Set-Top Box via DVI

This connection can only be made if there is a DVI Output jack on the external device.

1 Connect a HDMI/DVI Cable or

DVI-HDMI Adapter between the

HDMI3/DVI IN jack on the TV and

the DVI OUT jack on the DVD

Player/Set-Top Box.

2 Connect Audio Cables between

the DVI IN [L-AUDIO-R] jacks on

the TV and the AUDIO OUT jacks

on the DVD Player/Set-Top Box.

➢

Each DVD Player/Set-Top box has a different side panel configuration.

➢

When connecting a DVD Player/Set-Top box, match the color of the connection terminal to the cable.

Connecting a DVD Player/Set-Top Box via HDMI

This connection can only be made if there is an HDMI Output jack on the external device.

1 Connect an HDMI Cable between

the HDMI IN 1 (or HDMI IN 2 ) on

the TV and the HDMI OUT jack on

the DVD Player/Set-Top Box.

What is HDMI?

● HDMI, or high-definition multimedia interface, is a next-generation interface that enables the transmission of the digital audio and

video signals using a single cable.

● “Multimedia interface” is a more accurate name for it especially because it allows multiple channels of digital audio (5.1 channels).

The difference between HDMI and DVI is that the HDMI device is smaller in size, has the HDCP (High Bandwidth Digital Copy

Protection) coding feature installed, and supports multi-channel digital audio.

➢

Each DVD Player/Set-top box has a different side panel configuration.

➢

When connecting a DVD Player/Set-top box, match the color of the connection terminal to the cable.

➢

When connecting via HDMI, you do not need to connect Audio Cables. You only need to connect Audio cables when connecting

via HDMI/DVI.

TV Side Panel

DVD Player/Set-Top Box

Audio Cable(Not supplied)

2

HDMI Cable(Not supplied)

1

DVD Player/Set-Top Box

TV Side Panel

HDMI/DVI Cable(Not supplied)

1

BP68-00628B-00Eng_1.indd 14 2007-03-02 ｿﾀﾈﾄ 4:21:30

English - 15

Connecting a Digital Audio System

The side panel jacks on your TV make it easy to connect a Digital Audio System to your TV.

1 Connect an Optical Cable

between the DIGITAL AUDIO OUT

(OPTICAL) jack on the TV and

the Digital Audio Input jack on the

Digital Audio System.

When a Digital Audio System

is connected to the DIGITAL

AUDIO OUT (OPTICAL) terminal:

Decrease the volume of the TV,

and adjust the volume level with

the audio system’s volume control.

➢

Each Digital Audio System has a different side panel configuration.

➢

5.1CH audio is possible when the TV is connected to an external device supporting 5.1CH.

What is OPTICAL?

● Converts the electric signal into an optical light signal, and transmits it through glass fibers. S/PDIF is a transmission system of

digital audio in the form of a light wave that uses a glass conductor.

Connecting an Amplifier/DVD Home Theater

1 Connect Audio Cables between

the AV OUT [L-AUDIO-R] jacks on

the TV and AUDIO IN [L-AUDIO-R]

jacks on the Amplifier/DVD Home

Theater.

When an audio amplifier is

connected to the AV OUT [L-

AUDIO-R] terminals: Decrease the

volume of the TV, and adjust the

volume level with the amplifier’s

volume control.

➢

Each Amplifier/DVD Home Theater has a different side panel configuration.

➢

When connecting an Amplifier/DVD Home Theater, match the color of the connection terminal to the cable.

TV Side Panel

Optical Cable (Not supplied)

1

Digital Audio System

TV Side Panel

Audio Cable (Not supplied)

1

Amplifier/DVD Home Theater

BP68-00628B-00Eng_1.indd 15 2007-03-02 ｿﾀﾈﾄ 4:21:32

English - 16

Operation

Turning the TV On and Off

Press the POWER button on the remote control.

You can also use the POWER button on the TV.

➢

It may take a while when your TV starts.

Connecting a PC

Using the D-Sub Cable

1 Connect a D-Sub Cable between

the PC IN [PC] jack on the TV

and the PC output jack on your

computer.

2 Connect a PC Audio Cable

between the PC IN [AUDIO] jack

on the TV and the Audio Out

jack of the sound card on your

computer.

Using the HDMI/DVI Cable

1 Connect a HDMI/DVI Cable

between the HDMI3/DVI IN jack on

the TV and the PC output jack on

your computer.

2 Connect a 1Stereo/2RCA Cable

between the DVI IN [L-AUDIO-R]

jack on the TV and the Audio Out

jack of the sound card on your

computer.

➢

Each PC has a different side panel configuration.

➢

When connecting a PC, match the color of the connection terminal to the cable.

➢

When connecting the HDMI/DVI to your PC, select HDMI3/DVI in Edit Name from you PC to see the original screen with no cutting

images. See page 27.

TV Side Panel

PC

PC Audio Cable (Not supplied)

2

D-Sub Cable (Not supplied)

1

Using the D-Sub Cable

Using the HDMI/DVI Cable

TV Side Panel

PC

1Streo/2RCA Cable (Not supplied)

2

HDMI/DVI Cable (Not supplied)

1

BP68-00628B-00Eng_1.indd 16 2007-03-02 ｿﾀﾈﾄ 4:21:36

English - 17

Plug & Play Feature

When the TV is initially powered on, basic settings proceed automatically:

1 Press the POWER button on the remote control.

The message Executes the Plug & Play function when you set the TV at first or

reset it. Sets channels, clock and other functions. is automatically displayed.

2 Press the ENTER button to enter the language.

Press the ▲ or ▼ button to select language, then press the ENTER button.

The message Select Home Mode when installing this TV at home. is automatically

displayed.

3 Press the ◄ or ► button to select Shop or Home, then press the ENTER button.

➢

The default selection is Home.

➢

We recommend setting the TV to Home mode for the best picture in your home

environment.

➢

Shop mode is only intended for use in retail environments.

➢

If the unit is accidentally set to Shop mode, and you want to return to Dynamic

(Home) mode, press the Volume button and then hold down the

MENU button for

five seconds on the TV panel.

4 Press the ▲ or ▼ button to memorize the channels of the selected connection, then

press the ENTER button.

➢

If the antenna is connected to ANT 1 IN (CABLE), select Cable and if it is

connected to ANT 2 IN (AIR), select Air.

➢

If both ANT 1 IN (CABLE) and ANT 2 IN (AIR) are connected, select the Air +

Cable.

➢

In Cable mode, you can select the correct analog signal source among STD, HRC,

and IRC by pressing the ◄ or ► button, then press the ENTER button. If you have

Digital cable, select the signal source for both Analog and Digital.

Contact your local cable company to identify the type of cable system that exists in

your particular area.

5 The TV will begin memorizing all of the available channels.

After all the available channels are stored, the Auto program menu reappears.

Press the ENTER button when channel memorization is complete.

The Clock Mode menu is displayed.

➢

To stop the search before it has finished, press the ENTER button with stop

selected.

Continued...

Plug & Play

Executes the Plug & Play function when you set the TV

at first or reset it. Sets channels, clock and other

functions.

Exit

Enter

OK

Plug & Play

Select Language of the OSD.

Menu Language : English

English

Español

Français

SkipEnter

Plug & Play

Select Home Mode when installing this TV at home.

Home

Shop

SkipEnter

Plug & Play

Select the antennas to memorize

Air

Cable

Air+Cable

Start

Plug & Play

Selects the cable system.

Analog

Digital

STD

HRC IRC

SkipEnter

Plug & Play

Auto Program in Progress.

Stop

Cable 10

3%

SkipEnter

Plug & Play

Auto Program is completed.

3 channels are memorized.

Air : 1 Cable : 2

OK

SkipEnter

STD

Move

Digital Channels are added on the favorite

channel list.

BP68-00628B-00Eng_1.indd 17 2007-03-02 ｿﾀﾈﾄ 4:21:39

English - 18

6 Press the ENTER button.

Press the ▲ or ▼ button to select Manual for setting the current time manually, then

press the ENTER button. The message Set current date and time. is displayed.

➢

If you select Auto. Set to daylight saving time. is displayed, then go to step 9.

7 Press the ◄ or ► button to move to Month, Day, Year, Hour, Minute, or am/pm.

Set the date and time you want by pressing the ▲ or ▼ button, then press the ENTER

button.

➢

You can set the month, day, year, hour, and minute directly by pressing the number

buttons on the remote control.

8 The message Enjoy your watching. is displayed.

When you have finished, press the ENTER button.

➢

Even if the ENTER button is not pressed, the message will automatically disappear

after several seconds.

Setting the Clock Automatically

9 Press the ENTER button.

Press the ▲ or ▼ button to select Off or On, then the ENTER button.

The message Select the time zone in which you live. is displayed.

10 Press the ▲ or ▼ button to highlight the time zone for your local area (and to move the

highlight to the appropriate time zone on the map of the United States).

Press the ENTER button.

If clock is not automatically set, see pages 48~49 to set the clock.

11 The message

Enjoy your watching. is displayed.

When you have finished, press the ENTER button.

➢

Even if the ENTER button is not pressed, the message will automatically disappear

after several seconds.

SkipEnter

Plug & Play

Set the Clock Mode.

Clock Mode : Auto 

SkipEnter

Plug & Play

Set the Clock Mode.

Clock Mode : Auto

Auto

Manual

Plug & Play

Set current date and time

 

Month

 

Day

 

Year

 

Hour

 

Minute

 

am/pm

Enter

Skip

Move

Adjust

SkipEnter

Plug & Play

Set to daylight saving time.

DST : Off 

SkipEnter

Plug & Play

Set to daylight saving time.

DST : Off

Off

On

Plug & Play

Select the time zone in which you live.

SkipEnter

Newfoundland

Atlantic

Eastern

Central

Mountain

Pacific



Plug & Play

Enjoy your watching.

OK

Move

BP68-00628B-01Eng_1.indd 18 2007-03-09 ｿﾀﾈﾄ 5:22:48

English - 19

Changing Channels

Using the Channel Buttons

Press the CH or CH button to change channels.

➢

When you press the CH or CH button, the TV changes channels in sequence.

You will see all the channels that the TV has memorized. (The TV must have memorized at

least three channels). You will not see channels that were either erased or not memorized.

See page 21 to memorize channels.

Using the Number Buttons

Use the number buttons to quickly tune to any channel.

Press the number buttons to go directly to a channel.

For example, to select channel 27, press “2,” then “7.”

The TV will change channels when you press the second number.

Using the “

-

” Button

The “

-

” button is used to select stations that broadcast a digital signal.

For example, for Channel 7-1, press “7”, then “-”, and then “1”.

➢

HD indicates the TV is receiving a Digital High Definition signal.

SD indicates the TV is receiving a Standard Definition signal.

➢

For quick channel change, press the number buttons, then press the ENTER button.

Using the PRE-CH Button to select the Previous Channel

Press the PRE-CH button.

The TV will switch to the last channel viewed.

➢

To quickly switch between two channels that are far apart, tune to one channel, then use

the number button to select the second channel. Then use the PRE-CH button to quickly

alternate between them.

Adjusting the Volume

Press the VOL + or VOL – button to increase or decrease the volume.

Using the Mute Button

At any time, you can cut off the sound using the MUTE button.

1 Press the MUTE button and the sound cuts off.

The is displayed on the screen.

2 To turn mute off, press the MUTE button again, or simply press the VOL + or VOL – button.

BP68-00628B-00Eng_1.indd 19 2007-03-02 ｿﾀﾈﾄ 4:21:41

English - 20

Viewing the Display

The display identifies the current channel and the status of certain audio-video settings.

Press the INFO button on the remote control.

Viewing the Menus

1 With the power on, press the MENU button.

The main menu will appear at the bottom of the screen.

There are seven menu groups: Picture, Sound, Channel, Setup, Input, Guide,

and PIP.

2 Press the ▲ or ▼ button, then press the ENTER button to select an item you want in the

menu. Press the ▲/▼/◄/►/ENTER button to display, change, or use the selected items.

Press the EXIT button to exit.

Using the TOOLS Button

The Tools button allows you to display frequently used Menu and Connection items

with a Single button press.

1 Press the TOOLS button.

The TOOLS menu will appear.

2 Press the ▲/▼ button to select a menu, then press the ENTER button.

3 Press the ▲/▼/◄/►/ENTER buttons to display, change, or use the selected items.

For a more detailed description of each function, refer to the corresponding page.

● Device List, see page 82

Headset Connection, see page 69

Picture Setting, see page 28

Sound Setting, see page 36

Sleep Timer, see page 50

Caption, see page 51~52

Channel Add/Delete, see page 42

Delete Favorite Channel, see page 43

Auto Program, see page 21

Air

3

Mode

:

Dynamic

Contrast : 100

Brightness : 45

Sharpness : 75

Color : 55

Tint (G/R) : G50/R50

Color Tone : Cool1

Detail Settings

Picture

Device List

Headset Connection

Picture Setting

Sound Setting

Sleep Timer Off

Caption

Off

Channel Add/Delete

Delete Favorite Channel

Move

Enter

No Time Information

BP68-00628B-00Eng_1.indd 20 2007-03-02 ｿﾀﾈﾄ 4:21:45

La page charge ...

Samsung HL-T5689S Manuel utilisateur

Ce manuel convient également à

Samsung HL-T5689S Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents