Qbic Luminen 10 Touch Panel PC Mode d'emploi
- Taper
- Mode d'emploi
Luminen 10
Touch Panel PC
Quick Start Guide
Contents
Panel PC
Bracket Tape
I/O Cover M3 screw *1
M2M3
Indica�on
Installa�on
1.
2. Tape Mount
STEP 1
Connect cables. Device will
power on when DC/PoE+
is inserted.
STEP 2
Install I/O cover
STEP 3
Fix 2* M2 screws
STEP 1
Ah tape on the
back of bracket
STEP 2
Place the bracket on the
back side of Panel PC
STEP 3
Fasten M3 screw*1 to
secure the bracket and
back cover
STEP 4
Fix the Panel PC
on the surface
using tape
3. Surface Mount
STEP 1
Install bracket
on surface
(screws not included)
This Panel PC is al
to secure with M3 screw. The suggested length of the M3 screw is the thickness of
SA moung bracket plus 8mm(Screw not included).
Please ensure the moung surface is clean and smooth before using the tape.
M2 / M3 screw Torque<2 kgf-cm
Installaon height: <2M
STEP 2
Mount the Panel PC on
the bracket
STEP 3
Fasten M3 screw*1 to
secure the bracket
and back cover
NOTICE:
30°
30°
M2 screw *2
Bracket Kit
Reset
Power Button
MIC
1
2
3
Proximity Sensor
4
NFC
Display
Camera
5
6
7
Side LED
8
USB Type C for ADB
USB 3.0
9
10
11
RJ45 / PoE+
12
Reset hole DC IN
13
1211
10
9
6
7 14
8
1
4 5 13
12 Kensington
Lock Slot
14
2 3
DC power Adapter
(Op�onal)
Metal Stand
(Op�onal)
Heavy Oils: A degreaser or solvent-based cleaner may be required to remove heavy oil or grease from a surface and
Abrasion: Abrading a surface, followed by cleaning with IPA/water, can remove heavy dirt or
Porous Surfaces: need to be sealed
Unique Materials:
migrate
Typical surface cleaning solvents are IPA/ water mixture (rubbing alcohol) or heptane. * (Steps A and B)
Bond strength is dependent upon the amount of adhesive-to- surface contact developed.
(Steps C and D) (100 kPa) in roll down or platen pressure.
temperatures
General Procedure
NOTE : greater than
for use when handling such materials.
IPA
&
Water
Step A:
Solvent wipe
Step B:
Wipe dry
Step C:
Apply tape to surface
Step D:
Roll ished joint
should be followed by cleaning with IPA/water.
surface area to improve adhesion.
CARE AND WARNING
WA RNING :
Changes or mcas to this unit not expressly approved by the party responsible for compliance will void
the user’s authority to operate the equipment.
C orrect disposal of this product :
This marking indicates that this product should not be disposed with other household wastes throughout the EU.
To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly
to promote the sustainable reuse of material resources. To return your used device, use the return and collecn systems or contact
the retailer where the product was purchased. They can take this product for environmental safe recycling.
T he power consumpn of the product in networked standby is W) which all wired network ports
are connected and all wireless network ports are acated.
FCC & CE RF radiaon Exposure Statement Cauon : To maintain compliance with the FCC & CE`s RF exposure guidelines.
Place the product at least 20cm from nearby persons.
NOT E :
This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 1of the FCC Rules.
These limits are designed to provide reasonable protecn against harmful interference in a residenal installaon.
This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the
instrucons, may cause harmful interference to radio communicas.
However, there is no guarantee that interference will not occur in a parcular installa.If this equipment does cause harmful
interference to radio or television recep, which can be determined by turning the equipment oand on,
the user is encouraged to try to correct the interference by one or more of the following measures :
Reorient or relocate the receiving antenna.
Increase the separaon between the equipment and receiver.
Connect the equipment into an outlet on a circuit dint from that to which the receiver is connected.
Consult the dealer or an experienced radio/panel PC technician for help.
This device complies with Part 1of the FCC Rules. Operaon is subject to the following two condis :
May not cause harmful interference.
Must accept any interference received, including interference that may cause undesired opera.
type
CAUTION
Ris of explosion if the battery is replaced by an incorrect
Wait one-half hour after switching off before handling parts
or the leakage of
Qbic Technology Co.,Ltd.26F.-12,No.99.Sec.1,
Xintai 5th Rd., Xizhi Dist., New Taipei City 221, Taiwan(R.O.C)
TEL:886-2-2697-2000 FAX:886-2-2697-2868
Removal
STEP 1
Remove the top screw
connecg the Luminen 10
to the bracket
STEP 2
With both hands supporg
the top and bom of the
Luminen 10, carefully t the top
secon of Luminen 10 downward 30
STEP 3
Gently pull the Luminen 10
down to remove from bracket
STEP 4
Apply hot air gun to the
tape beneath bracket
unl loose
Slowly pull the tape and the
bracket downward othe surface
Discrete Cable Outlets
Luminen 10 is designed for landscape or portrait installaon with a discreet cable management system.
DO NOT remove bracket or tape from surface forcefully. Excessive force during
removal may lead to damaged surface.
NOTE:
30°
This product complies with FDA performance standards for laser products except for conformance with IEC
Date of manufacture: the date code shown on the product label represents the manufacturing date of this laser product.
CAUTION:
CAUTION:
CAUTION:
S/N : 0123456789 MADE IN TAIWANNOV/2022NOV/2022
-Month/Year
LASER SAFETY:
LASER
1
The ambient light sensor
can automatically adjust panel
brightness base on the environment.
See Display settings to enable automatic brightness.
The Laser proximity sensor will detec nearby motion to
wake the panel up without requiring a touch.
NOTE: Operating Temperature: 0~40°C
Power Adapter information:
Input: PoE 44V - 57V --- 0.4A
Input: Adapter 12V --- 1.5A
This unit is intended to be supplied by an UL / IEC 62368-1 certified Class II
power adapter suitable for use at minimum 40 degree C and altitude of
operation up to 5,000 m whose output complied with LPS/PS2 and meets
ES1, and is rated 12 V d.c., minimum 1.5 A or UL/IEC 62368-1 certified PoE
output power supply suitable for use at minimum 40 degree C and altitude
of operation up to 5,000 m whose output complied with LPS/PS2 and
meets ES1 and is rated 44-57 V d.c., minimum 0.4 A
(1) This device may not cause interference.
Canada, avis d'Industry Canada (IC)
The radiated output power of the Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. The
(antennas are greater than 20cm from a person's body).
---
-
1
-
2
Qbic Luminen 10 Touch Panel PC Mode d'emploi
- Taper
- Mode d'emploi
dans d''autres langues
Autres documents
-
Perixx PERIMICE-819 Manuel utilisateur
-
Perixx PERIMICE-813 Manuel utilisateur
-
resideo VX1 Guide d'installation
-
JouSecu B152 Manuel utilisateur
-
Apollo 2ACE9-51000300 Manuel utilisateur
-
JouSecu B255 Manuel utilisateur
-
Gallagher M5800i Mode d'emploi
-
Ashley 2170306 Manuel utilisateur
-
ELRO CBFS58R Manuel utilisateur
-
Gallagher W-0 Mode d'emploi