Q
uick Star
t
DESCRIPTION
The Combo PON D2 Small Form-factor Pluggable (SFP+)
combines the 10 G XGS-PON OLT and GPON OLT optical trans-
ceiver into a single-mode fiber SFP+. The SFP+ provides a single
optical interface to a physical interface and provides an XGS-PON
and a GPON interface to the supporting system when installed
into an appropriate module or system.
Both the XGS-PON and GPON optical burst mode receivers
incorporate APD/TIA optics for maximum sensitivity. The XGS-
PON transmitter incorporates a 1577 nm EML laser assembly and
the GPON transmitter incorporates a 1490 nm DFB laser
assembly. The SFP+ is designed to support extended ranges
within the optical distribution network of up to 37 km. It is FDA 21
CFR1040.10 and IEC 60825-1 Class I laser safety compliant and
meets the EU RoHS Directive.
This SFP+ supports the following features:
■ODN Class D2 (N2/C+) Transceiver
■Data rates:
♦XGS-PON 10 G down/10 G up
♦GPON 2.5 G down/1.25 G up
■XGS-PON Optical Receive Wavelength: 1270 nm
■XGS-PON Optical Transmit Wavelength: 1577 nm
■GPON Optical Receive Wavelength: 1310 nm
■GPON Optical Transmit Wavelength: 1490 nm
■Hot Pluggable
Applications:
■GPON, XGS-PON, and Combined GPON/XGS-PON Access
Networks
■Fiber to the Premises (FTTP)
■Fiber to the Building (FTTB)
■Fiber to the Curb (FTTC)
■Fiber to the Distribution Point (FTTDP)
Due to compliance certification requirements, use only pluggable
optics supplied by Adtran. Adtran cannot certify system integrity
with other pluggable optics.
INSTALLATION
Before installing the equipment, inspect the SFP+. If damage has
occurred during shipping, file a claim with the carrier, and then
contact Adtran Customer Support. For more information, refer to
the warranty.
Installation Steps
To install the SFP+ into an appropriate device, complete the
following steps:
g NOTE
Do not remove the protective dust cover from the SFP+ until the
fiber optic cable is ready to be connected.
1. Insert the SFP+ into the SFP+ cage on the module.
2. Slide the SFP+ all the way into the SFP+ cage until there is
an audible “click”.
g NOTE
■Orientation of the SFP+ will vary depending on the module.
■The latch on the SFP+ is for removal only. When removing the
SFP+, rotate the latch away from the SFP+. It should easily
slide out of the cage.
3. Continue the installation and turn-up of the host module
using the instructions in the Job Aid or Quick Start provided
with the module or other system-level documentation
available online at www.adtran.com.
Adtran Pluggable Optics
Combo PON D2 SFP+
For OLT
April 2022
61442543F2-13B
P/N: 1442543F2
261442543F2-13B
SAFETY AND REGULATORY
ENGLISH
f WARNING!
Read all warnings, cautions, notes, and installation instructions
before installing or servicing this equipment.
C CAUTION!
This product is a Class 1 Laser module that complies with FDA 21
CFR 1040.10, 1040.11 and IEC 60825-1.
f CAUTION!
■Electrostatic Discharge (ESD) can damage electronic devices.
When handling devices, wear an antistatic discharge wrist
strap to prevent damage to electronic components. Place
devices in antistatic packing material when transporting or
storing. When working on devices, always place them on an
approved antistatic mat that is electrically grounded.
■This product and the host system are designed and intended
for installation as part of either a Common Bonding Network
(CBN) or Isolated Bonding Network (IBN).
■This product’s outer case is “electrically isolated” from other
circuits, as a result, this product can be used in systems that
are installed either in a DC-I (isolated) or DC-C (common)
configuration. For Systems where other installed modules or
the host system itself have internal connections between
battery return and frame ground, the system can only be
deployed in a DC-C configuration.
■If the host system has a protective earth (PE) terminal, the PE
terminal of the host system must be connected to protective
earth (PE) to ensure that the exposed metal (i.e., front panels,
optical modules) on the product is properly grounded.
SPECIFICATIONS
General
■Module Type: SFP+
■Media Type: Fiber
♦Single-Mode
♦SC Connector
■Signal Data Rate:
♦9.953 Gbps (XGS-PON)
♦2.488 Gbps (GPON)
■Distance: up to 37 km
■Not compatible with SFP+ MSA
■Applications: XGS-PON, GPON, FTTP, FTTB, FTTC, FTTDP
Optical
■XGS-PON Transmitter
♦Laser Diode Type: EML
♦Transmit Wavelength: 1577 nm
♦Tx Power: +4.0 dBm to +7.0 dBm
♦Spectral Width: 1 nm
♦SMSR: 30.0 dBm
♦Extinction Ratio: 8.2 dB
■GPON Transmitter
♦Laser Diode Type: DFB
♦Transmit Wavelength: 1490 nm
♦Tx Power: +3.0 dBm to +7.0 dBm
♦Spectral Width: 1 nm
♦SMSR: 30.0 dBm
♦Extinction Ratio: 8.2 dB
■XGS-PON Receiver
♦Type: APD
♦Central Wavelength: 1270 nm
♦Receiver Sensitivity: –28.0 dBm
♦Receiver Overload: –7.0 dBm
■GPON Receiver
♦Type: APD
♦Central Wavelength: 1310 nm
♦Receiver Sensitivity: –30.0 dBm
♦Receiver Overload: –7.0 dBm
Environmental
■Protected Equipment Severe Environment (Outdoor)
♦System Ambient Operational Temperature Range:
–40°C to +70°C
♦Storage Temperature Range: –40°C to +85°C
♦Relative Humidity 5% to 95%, non-condensing
61442543F2-13B 3
g NOTE
■This product is designed to be deployed in GR-3108-CORE
environmental Class 1, 2, or 3.
■This product is NRTL Listed to the applicable UL Standards.
The product is designed to meet the applicable requirements
of Telcordia GR-63-CORE, GR-1089-CORE and GR-3108-
CORE. This product has also been evaluated to applicable
international standards and meets the requirements for CE
marking.
■This product is intended for deployment in locations such as
Central Offices and outside plant cabinets. This product is to
be installed and serviced by trained and qualified Service
personnel only.
■This device complies with Part 15 of the FCC rules. Operation
is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
■Changes or modifications not expressly approved by Adtran
will void the warranty.
■This product is designed to meet the following environmental
classes:
♦ETSI EN 300 019-1-1 “Classification of environmental
conditions; Storage,” Class 1.2
♦ETSI EN 300 019-1-2 “Classification of environmental
conditions, Transportation,” Class 2.3
♦ETSI EN 300 019-1-3 “Classification of environmental
conditions, Stationary use at weather protected locations,”
Class 3.3
■This product is designed to function without degradation during
exposure to all test severities per Class 3.3.
■This product meets EU RoHS Directive. Refer to
www.adtran.com for further information on RoHS/WEEE.
FRANÇAIS
f AVERTISSMENT!
Lisez toutes les mentions de danger et de prudence et les
remarques, ainsi que la notice d'installation, avant d'effectuer
l'installation ou l'entretien de cet équipement.
C ATTENTION!
Ce produit est un laser de classe 1 conforme à la norme FDA 21
CFR 1040.10 et 1040.11 et IEC 60825-1.
f ATTENTION!
■L'ESD (décharge électrostatique) peut endommager les
modules électroniques. Lors de la manipulation des modules,
portez un bracelet de décharge antistatique pour éviter
d’endommager les composants électroniques. Placez les
modules dans un emballage antistatique lors du transport ou
du stockage. Lorsque vous travaillez sur les modules, placez-
les toujours sur un tapis antistatique certifié muni d’un
branchement de mise à la terre.
■Ce produit et système hôte sont conçus et destinés à être
installés dans le cadre soit d'un réseau commun Bonding
(CBN) ou isolé Réseau Bonding (IBN).
■Si le système hôte est doté d'une borne de mise à la terre de
protection (PE), la borne PE du système hôte doit être
connectée à la mise à terre de protection (PE), afin d'assurer
que les parties métaliques à découvert (panneaux frontaux,
modules optiques) du produit soient correctement mis à terre.
g REMARQUE
Ce produit est conforme à la directive européenne RoHS.
Reportez-vous à www.adtran.com pour de plus amples rensei-
gnements sur RoHS.
CAUTION!
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY
HANDLING PRECAUTIONS REQUIRED
Warranty: Adtran will replace or repair this product within the warranty period if it does not meet
its published specifications or fails while in service. Warranty information can be found
online at www.adtran.com/warranty.
Trademarks: Brand names and product names included in this document are trademarks,
registered trademarks, or trade names of their respective holders.
Copyright © 2022 Adtran Inc. All Rights Reserved.
Adtran CUSTOMER CARE:
From within the U.S. 1.888.423.8726
From outside the U.S. +1 256.963.8716
PRICING AND AVAILABILITY 1.800.827.0807
*61442543F2-13B*
DEUTSCH
f WARNUNG!
Lesen Sie alle Warnungen, Gefahrenhinweise, Anmerkungen und
Installationsanweisungen bevor Sie dieses Gerät installieren oder
warten.
C VORSICHT!
Dieses Produkt ist ein Klasse 1 Laser, die mit FDA 21 CFR
1040.10 und 1040.11 und IEC 60825-1 entspricht.
f VORSICHT!
■Elektrostatische Entladung können elektronische Module
beschädigen. Tragen Sie beim Umgang mit Modulen ein
Erdungsarmband, um Schäden an den elektronischen
Komponenten zu vermeiden. Transportieren oder lagern Sie
Module in antistatischem Verpackungsmaterial. Bei der Arbeit
an den Modulen, achten Sie darauf, diese stets auf
antistatische, elektrisch geerdete Matten zu legen.
■Dieses Produkt und Host-System sind so konzipiert und für die
Installation als Teil entweder eine gemeinsame Bonding
Network (CBN) oder isoliert Bonding Network (IBN)
vorgesehen.
■Falls das Host-System über einen Schutzleiteranschluss (PE)
verfügt, muss der PE-Anschluss des Host-Systems mit dem
Schutzleiteranschluss (PE) verbunden werden, um
sicherzustellen, dass das freiliegende Metall (d. h.
Frontblenden, Optikmodule) am Produkt ordnungsgemäß
geerdet ist.
g HINWEIS
Dieses Produkt erfüllt die EU RoHS Richtlinie. Bitte besuchen Sie
www.adtran.com für ausführlichere Informationen zu
RoHS/WEEE.
Documentation for Adtran Network Solutions products is available for
viewing and download directly from the Adtran Support Community
website.
Go to: https://adtran.com/support
Registration is required.
Adtran offers training courses on our products, including customized
training and courses taught at our facilities or at customer sites.
For inquiries, go to: http://adtran.com/training
The following online documents and resources provide additional information for this product:
Adtran Pluggable Optics Compatibility Matrix (online tool, go to: http://www.adtran.com/
pluggableoptics)
-
1
-
2
-
3
-
4
