Poulan Pro PP446T Manuel utilisateur

Marque: Poulan Pro

Modèle: PP446T

Catégorie: Mini motoculteurs

Taper: Manuel utilisateur

Poulan PRO

Instruction Manual

Manual de Instrucciones

Manuel d'lnstructions

PP446T

For Occasional Use Only

WARNING:

Read and follow all Safety Rules and Operating Instructions before

using this product. Failure to do so can result in serious injury.

ADVERTENOIA:

Lea el manual de instrucciones y siga todas las advertencias e

instrucciones de seguridad. El no hacerlo puede resultar en le-

siones graves.

AVERTISSEMENT:

Lire le manuel d'instructions et bien respecter tousles avertisse-

ments et toutes les instructions de s6curite. Tout defaut de le

faire pourrait entraTner des blessures graves.

Electrolux Home Products, Inc.

1030 Stevens Creek Road

Augusta, GA30907

The Elecb'elux Group, The world's No. 1choice.

Krl CHEN, CLONING AN_ OUTOOOR APPLIanCES COMBINED

----_ DANGER! This pruner can _ Read and understand the

be dangerous! Careless or im- U instruction manual before

proper use can cause using the pruner.

serious or even fatal injury.

'_ Always wear appropriate ear protection, eye protection and head protection.

__. DANGER! Falling objects can cause severe head injury, Wear head

protection when operating this unit. Do not stand beneath branch beh_g

cut.

_k WARNING: Alwaysdisconnectspark

plug wire and place wire where it cannot contact

spark plug to prevent accidental starting when

setting up, transporting, adjusting or making re-

pairs except carburetor adjustments.

Because a pruner is a high-speed wood-cutting

tool, special safety precautions must be ob-

served to reduce the risk of accidents. Careless

or improper use of this tool can cause serious or

even fatal injury.

PLAN AHEAD

• Read this manual carefully until you

completely understand and can follow all

safety rules, precautions, and operating

instructions before attempting to use the unit.

• Restrict the use of your pruner to adult users

who understand and can follow safety rules,

precautions, and operating instructions found

on the unit and in this manual

INSTRUCTION SAFETY iNFORMATION

MANUAL ON THE UNIT

PRUNER SAFETY

• Wear protective gear. Always use

steel-toed safety footwear with non-slip

sotes; snug-fitting clothing; heavy, long

pants, and long sleeves; heavy-duty,

non-slip gloves; eye protection such as

non-fogging, vented goggles or face

screen; an approved safety hard hat; and

sound barriers (ear plugs or mufflers) to

protect your hearing, Regular users should

have hearing checked regularly as engine

noise can damage hearing. Secure hair

above shoulder _ength. Secure or remove

loose clothing and jewelry or clothing with

loosely hanging ties, straps, tassels, etc,

Hearing Safety Hat

Protection _ Eye

""_ i U,o_d¢"" Protection

Snug Heavy Duty

Clothing Gloves

Safety Safety Chaps

Shoes

• Keep all parts of your body away from the

chain when the engine is running.

• Keep children, bystanders, and animals a

minimum of 50 feet (15 meters) away from

the work area. Do not allow other people or

animals to be near when starting or

operating the pruner.

HAZARD ZONE

50 feet

i_"-......_..J (15 meters)

DANGER: Do not

use near electrical

wires or power lines,

'_ Keep pruner at least

30 feet (10 meters)

away from all power

lines.

• Donothandleoroperateaprunerwhenyou

arefatigued,ill,orupset,orifyouhavetaken

atcohol,drugs,ormedication.Youmustbein

goodphysicalconditionandmentallyalert.If

youhaveanyconditionthatmightbe

aggravatedbystrenuouswork,checkwith

doctorbeforeoperatingapruner.

• Donotoperatetheprunerwithonehand.

Seriousinjurytotheoperator,helpers,

bystandersoranycombinationofthese

personsmayresultfromone-handed

operation.A pruneris intendedfor

two-handeduse.

• Operatepruneronlyinawell-ventilated

outdoorarea.

• Donotoperateprunerfromaladderorina

tree.

• Donotuseaprunertocutdowntreesorany

portionofthetreetrunk.

• Onlyuseforpruninglimbsorbranches

overheadnotgreaterthan4inches(10cm)

indiameter.

• Neverstandunderthelimbyouarepruning.

Alwayspositionyourselfoutofthepathof

fallingdebris.

• Donotcutsmallbrushandsaplingswiththe

pruner.Slendermattermaycatchinthe

chainandbewhippedtowardyou.pulling

youoffbalance.

• Makesurethechainwillnotmakecontact

withanyobjectwhilestartingtheengine.

Nevertrytostarttheunitwhentheguide

barisinacut.

• Donotputpressureontheprunerattheend

ofthecut.Applyingpressurecancauseyou

totosecontrotwhenthecutiscompIeted.

• Donotruntheunitathighspeedwhennot

pruning.

• Ifyoustrikeorbecomeentangledwitha

foreignobject,stoptheengineimmediately

andcheckfordamage.Haveanydamage

repairedbyanauthorizedservicedealer

beforeattemptingfurtheroperations.

• Donotoperateaprunerthatisdamaged,

improperlyadjusted,ornotcompletelyand

securelyassembled.Alwaysreplacebar

andchainimmediatetyif it becomes

damaged,brokenorisotherwiseremoved.

• Alwaysstoptheunitwhenworkisdelayed

orwhenwalkingfromonecuttinglocationto

another.Stoptheenginebeforesettingthe

unitdown.

• Carefullyptanyourpruningoperationin

advance.Donotstartcuttinguntityouhave

aclearworkarea,securefooting,anda

ptannedretreatpath.

• Useonlyindaylightorgoodartificiallight.

• Useonlyforjobsexplainedinthismanual

(ormanualsforoptionalattachments).

LINE TRIMMER SAFETY

_DANGER: Never use blades with line

trimmer attachment. Never use flailing de-

vices with any attachment, This unit (when

used with supplied line trimmer attachment) is

designed for line trimmer use only, Use of any

other accessories with line trimmer attach-

ment will increase the risk of injury.

'_WARNING: Trimmer line throws ob-

jects violently. You and others can be blinded/in-

jured. Wear eye and leg protection. Keep body

parts clear of rotating line.

o eotion

Keep children, bystanders, and animals 50 feet

(15 meters) away. Stop unit immediately if ap-

proached.

•Dress properly. Always wear safety

glasses or similar eye protection when

operating, or performing maintenance, on

your unit (safety glasses are available).

Eye protection should be marked Z87.

• Always wear face or dust mask ifoperation

is dusty.

• Always wear heavy, long pants, long

sleeves, boots, and gloves. Wearing safety

leg guards is recommended.

• Always wear foot protection. Do not go

barefoot or wear sandals. Stay clear of

spinning line.

• Secure hair above shoulder length. Secure

or remove loose clothing or clothing with

loosely hanging ties, straps, tassels, etc.

They can be caught in moving parts.

• Being fully covered also helps protect you

from debris and pieces of toxic plants

thrown by spinning line.

• Stay Alert. Do not operate this unit when

you are tired, ill, upset or under the

influence of alcohol, drugs, or medication.

Watch what you are doing; use common

sense.

• Wear hearing protection.

• Never start or run inside a closed room or

building. Breathing exhaust fumes can kill.

• Keep handles free of oil and fuel.

• Always keep engine on the right hand side

of your body.

• Hotd the unit firmly with both hands.

• Keep trimmer head (or other optional

attachment) below waist level and away

from all parts of your body. Do not raise

engine above your waist.

• Keep all parts of your body away from

muffler and spinning line (or other optional

attachment). Keep engine below waist

level. A hot muffler can cause serious

burns.

• Keep firm footing and balance. Do not

overreach or use from unstable surfaces

such as ladders, trees, steep slopes.

rooftops, etc.

• Use only in daylight or good artificial light.

• Use only for jobs explained in this manual

(or manuals for optional attachments).

MAINTAIN YOUR UNIT IN GOOD

WORKING ORDER

• Disconnect the spark plug before

performing maintenance except carburetor

adjustments.

• Look for and rep}ace damaged or loose

parts before each use. Look for and repair

fuel leaks before use. Keep in good working

condition.

• Make certah_the chain stops movingwhen

the throttle trigger is released. For

correction, refer to CARBURETOR

ADJUSTMENTS.

• Replace trimmer head parts that are

chipped, cracked, broken, or damaged in

any other way before using the unit.

• Never modify your unit in any way.

• Keep the handles dry, clean, and free of oil

or fuel mixture.

• Keep fuel and oil caps, screws, and

fasteners securely tightened.

• Maintain unit according to recommended

procedures. Keep cutting line at proper

length.

• Use only 0.080" (2 mm) diameter Poulan

PRO_ brand line. Never use wire, rope,

string, etc.

• Install required shield properly before using

the unit. Use only specified trimmer head;

make sure it is properly installed and

securely fastened.

• Make sure unit is assembled correctly as

shown in this manual.

• Make carburetor adjustments with lower

end supported to prevent line from

contacting any object.

• Keep others away when making carburetor

adjustments.

• Use only recommended Pou}ae PRO_

accessories and replacement parts.

• Have all service performed by a qualified

service dealer with the exception of the

items listed in the maintenance section of

this manual.

HANDLE FUEL WITH CAUTION

• Do not smoke while handling fuel or while

operating the unit.

• Eliminate alt sources of sparks or flame in

the areas where fuel is mixed or poured.

There should be no smoking, open flames,

or work that could cause sparks. Allow

engine to cool before refueling.

• Mix and pour fuel in an outdoor area on bare

ground; store fuel in a cool dry, well

ventilated place; and use an approved,

marked container for all fuel purposes.

Wipe up all fuel spills before starting engine.

• Move at least 10 feet (3 meters) from fueling

site before starting engine.

• Turn the engine off and let unit cool in a

non-combustible area, not on dry leaves,

straw, paper, etc. Slowly remove fuel cap

and refuel unit.

• Store the unit and fuel in an area where fuel

vapors cannot reach sparks or open flames

from water heaters, electric motors or

switches, furnaces, etc.

• Stop engine and allow to cool before

removing fuel cap.

•Always store gasoline in a container

approved for flammable liquids.

KICKBACK

_WARNING: Avoid kickback which

can result in serious injury. Kickback is the

backward, upward or sudden forward motion

of the guide bar occurring when the chain

near the upper tip of the guide bar contacts

any object such as a log or branch, or when

the wood closes in and pinches the chain in

the cut. Contacting a foreign object in the

wood can also result in loss of control.

•Rotational Kickback can occur when the

moving chain contacts an object at the upper

tip of the guide bar. This contact can cause

the chain to dig into the object, which stops

the chain for an instant. The result is a

lightning fast, reverse reaction which kicks the

guide bar up and back toward the operator.

•Pinch-Kickback can occur when the wood

closes in and pinches the moving chain in

the cut along the top of the guide bar and the

chain is suddenly stopped. This sudden

stopping of the chain results in a reversal of

the chain force used to cut wood and

causes the pruner to move in the opposite

direction of the chain rotation. The pruner is

driven straight back toward the operator.

• Pull-In can occur when the moving chain

contacts aforeign object in the wood in the cut

along the bottom of the guide bar and the

chain is suddenly stopped. This sudden

stopping pulls the pruner forward and away

from the operator and could easily cause the

operator to lose control of the prunen

REDUCE THE CHANCE OF

KICKBACK

• Recognizethat kickback can happen. With

a basic understanding of kickback, you can

reduce the element of surprise which

contributes to accidents.

• Never _et the moving chain contact any

object at the tip of the guide bar.

• Keep the working area free from

obstructions such as other trees, branches,

rocks, stumps, etc. Eliminate or avoid any

obstruction that your chain could hit while

you are cutting. When cutting a branch, do

not let the guide bar contact branch or other

objects around it.

• Keep your chain sharp and properly

tensioned. A loose or dull chain can

increase the chance of kickback occurring.

Follow manufacturer's chain sharpening

and maintenance instructions. Check

tension at regular intervals with the engine

stopped, never with the engine running.

Make sure the bar clamp nut is securely

tightened after tensioning the chain.

• Begin and continue cutting at full speed. If

the chain is moving at a slower speed, there

is greater chance of kickback occurring.

• Cut one branch at a time.

• Use extreme caution when re-entering a

previous cut.

• Do not attempt cuts starting with the tip of

the bar (plunge cuts).

• Watchforshiftingofwoodorotherforcesthat

couldcloseacutandpinchorfallintochain,

• UsetheReduced-KickbackGuideBarand

Low-KickbackChainspecifiedforyourunit.

MAINTAIN CONTROL

• Keep a good, firm grip on the pruner with

both hands when the engine is running and

don't let go, A firm grip wifl help you reduce

kickback and maintain control. Keep the

fingers of your left hand encircling and your

left thumb under the assist handle, Keep

your right hand completely around the

throttle handle whether your are right

handed or left handed.

• Stand with your weight evenly balanced on

both feet,

• Stand slightly to the left side ofthe pruner to

keep your body from being in a direct line

with the cutting chain,

KICKBACK SAFETY FEATURES

The following features are h_cluded on your

pruner to help reduce the hazard of kickback;

however, such features will not totally elimi-

nate this danger. As a pruner user, do not rely

only on safety devices. You must follow all

safety precautions, instructions, and mainte-

nance in this manual to help avoid kickback

and other forces which can result in serious

injury,

• Reduced-Kickback Guide Bar, designed

with a small radius tip which reduces the

size of the kickback danger zone on the bar

tip,

Reduced Kickback Symmetrical Guide Bar

_all Radius Tip

SymmetficaJ Guide Bar I_._

Large Radius Tip

• Low-Kickback Chain, designed with a

contoured depth gauge and guard link

which deflect kickback force and allow

wood to gradually ride into the cutter.

Contoured Depth Gauge

Elongated Guard Link

Deflects

_/- | kickback force

Low-Kickback _ and allows wood

Chain to gradually ride

into cutter

_Can Obstruct Material

Not a Low- Kickback Chain

SAFETY NOTICE: Exposure to vibrations

through prolonged use of gasoline powered

hand tools could cause blood vessel or nerve

damage in the fingers, hands, and joints of

people prone to circulation disorders or ab-

normal swellings. Prolonged use in cold

weather has been linked to blood vessel dam-

age in otherwise healthy people. If symptoms

occur such as numbness, pain, loss of

strength, change in skin color or texture, or

loss of feeling in the fingers, hands, or joints,

discontinue the use of this tool and seek med-

ical attention, An anti-vibration system does

not guarantee the avoidance of these prob-

lems. Users who operate power tools on a

continual and regular basis must monitor

closely their physical condition and the condi-

tion of this tool,

SPECIAL NOTICE: This unit is equipped

with a temperature fimiting muffler and spark

arresting screen which meets the require-

ments of California Codes 4442 and 4443. All

U.S. forest land and the states of California,

idaho, Maine, Minnesota, New Jersey, Ore-

gon, and Washington require by law that

many internal combustion engines be

equipped with a spark arresting screen, Ifyou

operate in a Iocale where such regulations ex-

ist, you are legally responsible for maintaining

the operating condition of these parts, Failure

to do so is a violation of the law, For normal

homeowner use, the muffler and spark arrest-

ing screen will not require any service. After

50 hours of use, we recommend that your

muffler be serviced or replaced by an autho-

rized service dealer,

ADDITIONAL SAFETY RULES

FOR OPTIONAL ATTACHMENTS

AO&WARNING: For each optional at-

tachment used, read entire instruction manu-

al before use and follow aft warnings and in-

structions in manual and on attachment,

A_,WARNING: Ensure handlebar is

instafled when using edger or brushcutter at-

tachments, Attach handlebar above arrow on

safety label on the upper shaft (engine end of

unit). If your edger or brushcutter attachment

does not include a handlebar, a handlebar ac-

cessory kit (#530071451) is available from

your authorized service dealer.

Handlebar

EDGER SAFETY

WARNING: Inspect the area to be

edged before each use. Remove objects

(rocks, broken glass, nails, wire, etc.) which

can be thrown by the blade or can wrap

around the shaft.

•Blade rotates momentarily after the trigger

is released. The blade can seriously cut

you or others.

• Allow blade to stop before removing it from

the cut.

Blade rotates Allow blade to stop

before removing it

afler the from the cut.

• Throw away blades that are bent, warped,

cracked, broken or damaged in any other

way. Replace parts that are cracked,

chipped, or damaged before using the unit.

• Do not attempt to remove cut material nor

hoid material to be cut when the engine is

running or when cutting blade is moving.

• Always keep the wheel and depth adjusting

skid in contact with the ground.

• Always push the unit slowly over the

ground. Stay alert for uneven sidewalks,

holes in the terrain, large roots, etc.

• Always use the handlebar when using edg-

er attachment.

BLOWER/VACUUM SAFETY

_WARNING: Inspect area before

starting unit. Remove all debris and hard ob-

jects such as rocks, glass, wire, etc. that can

ricochet, be thrown, or otherwise cause injury

or damage during operation.

• Do not set unit on any surface except a

clean, hard area while engine is running.

Debris such as gravel, sand, dust, grass,

etc., could be picked up by the air intake

and thrown out through discharge opening,

damaging unit, property, or causing serious

injury to bystanders or operator.

• Never place objects inside the blower

tubes, vacuum tubes or blower outlet. Al-

ways direct the blowing debris away from

people, animals, glass, and solid objects

such as trees, automobiles, wails, etc. The

force of air can cause rocks, dirt, or sticks to

be thrown or to ricochet which can hurt

people or animals, break glass, or cause

other damage.

• Never run unit without the proper equip-

ment attached. When using your unit as a

blower, always install blower tubes.

• Check air intake opening, blower tubes or

vacuum tubes frequently, always with en-

gine stopped and spark plug disconnected.

Keep vents and discharge tubes free of de-

bris which can accumulate and restrict

proper air flow.

• Never place any object in air intake opening

as this could restrict proper air flow and

cause damage to the unit.

• Never use for spreading chemicals, fertiliz-

ers, or other substances which may contain

toxic materials.

• To avoid spreading fire, do not use near leaf

or brush fires, fireplaces, barbecue pits,

ashtrays, etc.

BRUSHCUTTER SAFETY

,_ DANGER: Blade can thrust viotentIy

away from material it does not cut. Blade

thrust can cause amputation of arms or legs.

,_ WARNING: Do not use trimmer head

as a fastening device for the blade.

=I=

.'_WARNING: The blade continues to

spin after the throttle is released or engine is

turned off. The coasting blade can throw ob-

jects or seriously cut you if accidentally

touched. Stop the blade by contacting the

right hand side of the coasting blade with ma-

terial already cut.

S[°cPCi_yStionrgact _ _4 _:__

with cut material.

=I=

="=WARNING: Inspect the area to be

cut before each use. Remove objects (rocks,

broken glass, nails, wire, etc.) which can be

thrown or become entangled in the blade or

trimmer line.

• Throw away and replace blades that are

bent, warped, cracked, broken or damaged

in any other way.

• Installrequiredshietdproperlybeforeusing

theunit.Usethemetalshieldforallmetal

Madeuse.

_' WARNING: Only use brushcutter at-

tachments that provide a metal shield with

proboscis nose. FrOo OSS,S

•Use only specified blade and make sure it is

properly installed and securely fastened,

• Cut from your left to your right. Cutting on

the right side of the shield will throw debris

away from the operator.

• Always use the handlebar and a properly

adjusted shoulder strap with blade (see AS-

SEMBLY instructions in brushcutter attach-

ment instruction manual).

CULTIVATOR SAFETY

_' WARNING: Rotating tines can cause

serious injury. Keep away from rotating tines.

Stop the engine and disconnect the spark plug

before unclogging tines or making repairs.

_,jiiji_iiiiii!i_i_!!_iiliii!i!_ii!iii!i!ii!i!iil!!i_,

iiI

411WARNING: Inspect the area to be

cultivated before starting the unit. Remove all

debris and hard and sharp objects such as

rocks, vines, branches, rope, string, etc.

• Avoid heavy contact with solid objects that

might stop the tines. If heavy contact oc-

curs, stop the engine and inspect the unit

for damage.

• Never operate the cultivator without the tine

cover in place and properly secured.

• Keep the tines and guard clear of debris.

• After striking a foreign object, stop the engine,

disconnect the spark plug and inspect the cul-

tivator for damage. Repair before restarting.

• Disconnect attachment from the drive en-

gine before cleaning the tines with a hose

and water to remove any build-up. Oil the

tines to prevent rust.

• Always wear gloves when servicing or

cleaning the tines. The tines become very

sharp from use.

• Do not run unit at high speed unless culti-

vating,

HEDGE TRIMMER SAFETY

,_DANGER: RiSK OF CUT; KEEP

HANDS AWAY FROM BLADE - Blade

moves momentarily after the trigger is re-

leased. Do not attempt to clear away cut ma-

teriai when the blade is in motion. Make sure

the switch is in the OFF position, the spark

plug wire is disconnected, and the blade has

stopped moving before removing jammed

material from the cutting blade. Do not grab or

hold the unit by the cutting blade,

Blades move Allow blades to stop

momentarily before removing

after the them from the cut.

,_ WARNING: Inspect the area before

starting the unit. Remove all debris and hard

objects such as rocks, glass, wire, etc, that

can ricochet, be thrown, or otherwise cause

injury or damage during operation.

• Do not use a cutting blade that is bent,

warped, cracked, broken or damaged in any

other way, Have worn or damaged parts re-

placed by your authorized service dealer,

• Always keep unit in front of your body,

Keep atl parts of your body away from the

cutting blade.

• Keep the cutting blade and air vents clear of

debris,

SNOW THROWER SAFETY

,_WARNING: Keep hands and feet

away from the rotor when starting or running

the engine. Never attempt to clear the rotor

with the engine/motor running. Stop engine

and disconnect spark plug before unclogging

snow or debris from discharge chute or when

adjusting vanes.

_bWARNING: Never lean over dis-

charge chute. Rocks or debris could be

thrown into the eyes and face and cause seri-

ous injury or biindness.

Ag&WARNING: inspect the area where

the unit is to be used. Remove objects that

could be thrown or damage the unit. Some

objects may be hidden by fallen snow - be

alert for the possibility.

• Direct material discharge away from glass

enclosures, automobiles, etc.

• Do not run engine at high speed while not

removing snow.

• Be attentive when using the snowthrower,

and stay alert for holes in the terrain and

other hidden hazards.

• Make sure the rotor will spin freely before

attaching the snowthrower to the power-

head.

• If the rotor will not rotate freety due to frozen

ice. thaw the unit before thoroughly before

attempting to operate under power.

• Keep the rotor clear of debris.

• Do not throw snow near other people. The

snow thrower could propel small objects at

high speed causing injury.

• After striking a foreign object, stop the en-

gine. disconnect spark plug and inspect the

snowthrower for damage and repair if nec-

essary before restarting unit.

• Never operate the snowthrower near glass

enclosures, automobiles and trucks.

• Never attempt to use the snowthrower on a

roof.

•Never operate the snowthrower near win-

dow wells, dropoffs, etc.

• Never discharge snow onto public roads or

near moving traffic.

• Clear snow from slopes by going up and

down; never across. Use caution when

changing directions. Never clear snow

from steep slopes.

• Let snowthrower run for a few minutes after

clearing snow so moving parts do not

freeze.

• Look behind and use care when backing

up. Exercise caution to avoid slipping or fai-

ling. especially when operating in reverse.

• Know how to stop quickly.

AlL

rmWARNING: Ifreceived assembled,

repeat ali steps to ensure your unit is properly

assembled and all fasteners are secure.

Examh_e parts for damage. Do not use dam-

aged parts.

NOTE: If you need assistance or find parts

missing or damaged, call 1-800-554-6723.

It is normal for the fuel filter to rattle in the

empty fuel tank.

Finding fuel or oil residue on muffler is normal

due to carburetor adjustments and testing

done by the manufacturer.

TOOLS REQUIRED

• Hex wrench (provided)

INSTALLING PRUNER OR LINE

TRIMMER ATTACHMENTS

CAUTION: When removing or installing at-

tachments, place the unit on a flat surface for

stability.

1. Loosen the coupler by turning the knob

counterclockwise.

Coupler

Shipping

protector

Knob

TIGHTEN

2. Remove shipping protector from coupler.

3. Remove the shaft cap from the attach-

ment (if present).

4. Position locking/release button of attach-

ment into guide recess of coupler.

5. Push the attachment into the coupler until

the locking/release button snaps into the

primary hole.

6. Before using the unit. tighten the knob se-

curely by turning clockwise.

Coupler Primary Hole

Guide Recess

Upper Locking/ Lower

Release

Shaft Attachment

Button

rmWARNING: Make sure the locking/

release button is locked in the primary hole

and the knob is securely tightened before op-

erating the unit. Ali attachments are designed

to be used in the primary hole.

For optional attachments, see the AS-

SEMBLY section of the applicable attach-

ment instruction manual.

SHOULDER STRAP ASSEMBLY

_,WARNING: Proper shoulder strap

adjustments must be made with the engine

completely stopped before using unit.

1. Try on shoulder strap and adjust for fit

and balance before starting the engine or

beginning a cutting operation.

2. Insert your right arm and head through

the shoulder strap and allow it to rest on

your left shoulder. Make sure the danger

sign is centered on your back and the

hook is to the right side of your waist.

NOTE: A one-half twist is built in the shoul-

der strap to allow the strap to rest fiat on the

shoulder.

3. Adjust the strap, allowing the hook to be

about 3 - 6 inches (8 - 15 cm) below the

waist.

4. Fasten the strap hook to the clamp lo-

cated between the throttle handle and the

assist handle and lift the tool to the oper-

ating position.

NOTE: It may be necessary to relocate the

shoulder strap clamp on the shaft for proper

balancing of unit.

TO RELOCATE SHOULDER STRAP

CLAMP:

1. Loosen and remove both clamp screws.

2. Place the upper shoulder strap clamp

over the upper shaft.

3. Positionthelowershoulderstrapclamp

undertheuppershaftandaligntheupper

andlowerclampscrewholes.

POWERHEAD

END StrapClamp

Lower Shoulder • Aqq-ACHMENT

Strap Clamp | _. END

!Screws

4. Insert two screws into the screw holes.

5. Secure shoulder strap clamp by tighten-

ing screws with a hex wrench.

ADJUSTING THE ASSIST HANDLE

_IIWARNING: When adjusting the as-

sist handle, be sure it remains between the

coupler and the _ lower arrow (closest to

coupler) on the safety label to ensure proper

balancing of unit. When adjusting the assist

handle or handlebar during use of optional at-

tachments, it must be repositioned between

the throttle trigger and the _ upper arrow

(closest to engine) on the safety label.

1. Loosen wing nut on handle.

2. Rotate the handle on the shaft to an up-

right position; retighten wing nut.

ATTACHING SHIELD (FOR LINE

TRIMMER ATTACHMENT)

,_i, WARNING: Theshieldmustbeprop-

erlyinstalled. The shield provides partial protec-

tion from the risk of thrown objects to the opera-

tor and others and is equipped with a line limiter

blade which cuts excess line to the proper

length. The line limiter blade (on underside of

shield) is sharp and can cut you. For proper

orientation of shield, see KNOW YOUR TRIM-

MER illustration in OPERATION section.

1. Remove wing nut from shield.

2. Insert bracket into slot as shown.

3. Pivot shield until bolt passes through hole

in bracket.

4. Securely tighten wing nut onto bolt.

Slot

Shield /

__iiii Bra/cket

Une Limiter Blade _ _ NWiu_g

KNOW YOUR PRUNER

READTHIS INSTRUCTION MANUALAND SAFETY RULESBEFORE OPERATINGYOUR UNIq:

Compare the illustrationswith your unit to familiarize yourself with the location of the various controls

and adjustments. Save this manual for future reference.

Pruner

Line Trimmer

Attachment

Bar

ON/OFF SWITCH

Shaft Shoulder Strap Clamp

Attachment Hanger Starter Handle ,_

Bar oil fill cap

Chain

Bar nut

The ON/OFF switch is located on the trigger

handle and is used to stop the engine. Move the

switch to the OFF position to stop the engine.

Switch

Fuel mix

fill cap

Primer

Bulb

Choke Lever Muffler

PRIMER BULB

The PRIMER BULB removes air from the car-

buretor and fuel lines and fills them with fuel.

This allows you to start the engine with fewer

pulls on the starter rope. Activate the primer bulb

by pressing it and allowing itto return to its origi-

nal form.

CHOKE

TheCHOKEhelpstosupplyfueltotheengine

toaidincoldstarting.Activatethechokeby

movingthechokelevertotheFULLCHOKE

position.Aftertheengineattemptstostart,move

thechokelevertotheHALFCHOKEposition.

Onceenginehasstarted,movethechokelever

totheOFFCHOKEposition.

COUPLER

The COUPLER enables optional attach-

ments to be instafled on the unit.

CHAIN TENSION

it is normal for a new chain to stretch during

first 15 minutes of operation. You should

check your chain tension frequentIy. See

CHAIN TENSION in the SERVICE AND AD-

JUSTMENTS section.

BEFORE STARTING ENGINE

,_ WARNING: Besureto read the fuel

information inthe safety rules before you be-

gin. if you do not understand the safety rules,

do not attempt to fuel your unit. Call

1-800-554-6723,

FUELING ENGINE

,_ WARNING: Remove fuel cap slowly

when refueling.

HELPFUL TIP I

Toobtain thecorrect oil mix I

tratio, pour 8.2 ounces of I

2-cycle synthetic oil into

one gallon of fresh gas.

This engine is certified to operate on

unleaded gasoline. Before operation,

gasoline must be mixed with a good quality

synthetic 2-cycle air-cooled engine oil

designed to be mixed at a ratio of 40:1.

Poulan/Weed Eater brand synthetic oil is

recommended. Mix gasoline and oil at a ratio

of 40:1. A 40:1 ratio is obtained by mixing 3.2

ounces (95 ml) of oil with 1 gallon (4 liters) of

unleaded gasoline. DO NOT USE automotive

oil or marine oil. These oils will cause engine

damage. When mixing fuel, follow instructions

printed on container. Once oil is added to

gasoline, shake container momentarily to

assure that the fuel is thoroughly mixed. Always

read and follow the safety rules relating to fuel

before fueling your unit.

BAR AND CHAIN LUBRICATION

The bar and chain require lubrication. The chain

oiler provides continuous lubrication to the chain

and guide bar. Be sure to fill the bar oil tank

when you fillthe fuel tank (Capacity = 4.6 ft.oz.).

Lack of oil wilt quickly ruin the bar and chain.

Too little oil will cause overheating shown by

smoke coming from the chain and/or discolor-

ation of the bar. The oil output is automatically

metered during operation. Always fill the bar oil

tank when you fill the fuel tank.

Genuine Poulan(R; or Poulan PROR; bar and

chain oil is recommended to protect your unit

against excessive wear from heat and fric-

tion. Poulan% or Poulan PROR; oil resists

high temperature thinning. If Poulanr¢ or Pou-

lan PRO _; bar and chain oil is not available,

use a good grade SAE 30 oil.

•Never use waste oil for bar and chain

lubrication.

• Always stop the engine before removing

the oil cap.

IMPORTANT

Experience indicates that alcohol blended

fuels (called gasohol or using ethanol or

methanol) can attract moisture which leads to

separation and formation of acids during stor-

age. Acidic gas can damage the fuel system

of an engine while in storage. To avoid engine

problems, empty the fuel system before stor-

age for 30 days or longer. Drain the gas tank.

start the engine and let it run until the fuel lines

and carburetor are empty. Use fresh fuel next

season. Never use engine or carburetor

cleaner products in the fuel tank or permanent

damage may occur.

See the STORAGE section for additional in-

formation.

HOW TO STOP YOUR UNIT

• To stop the engine, move the ON/OFF

switch to the OFF position.

• If engine does not stop, move choke lever

to the FULL CHOKE position.

ON/OFF Switch

HOW TO START YOUR UNIT

_L, WARNING: Make sure the chainwill

not make contact with any object while start-

ing the engine. Never try to start the unit when

the guide bar is in a cut. Avoid any contact

with the muffler. A hot muffler can cause seri-

ous burns.

eHELPFUL TIP I

!fY°ur engine still d°ee n°t I

start after following these

instructions, pleas e car!

1-800-554-5728.

STARTING A COLD ENGINE (or a

warm engine after running out of

fuel)

_ _-4_ _ Starting Position

Primer Bulb

Choke

_Lever

NOTE: If engine dies with the choke lever

in the OFF CHOKE position, move the

choke lever to the HALF CHOKE position

and pull the rope until engine runs, but no

more than 6 pulls.

Muffler

1. Set unit on a flat surface.

2. Move ON/OFF switch to the ON position.

3. Slowly press the primer bulb 6 times.

4. Move choke lever to FULL CHOKE by

aligning lever with position shown on de-

cal (see illustration below).

5. Squeeze the throttle trigger fully and hold

through all remaining steps,

6. Pull starter rope handle sharply until en-

gine sounds as if it is trying to start, but do

not pull rope more than 6 times.

7. As soon as engine sounds as if it is trying

to start, move choke tever to HALF

CHOKE by aligning lever with position

shown on decal

Choke

position

decal

8. Pull starter rope sharply until engine runs,

but no more than 6 pulls. If the engine

doesn't start after 6 pulls (at the HALF

CHOKE position), move the choke lever to

the FULL CHOKE position and press the

primer butb 6 times. Squeeze and hold the

throttle trigger and puff the starter rope 2

more times. Move the choke lever to the

HALF CHOKE position and puff the starter

rope until the engine runs. but no more than

6 pulls. If the engine doesn't start, repeat

procedure 2 additional times. NOTE: If

engine stili doesn't start, it is probably

flooded. Proceed to STARTING A

FLOODED ENGINE.

9. Once the engine starts, allow itto run 10 se-

conds, then move the choke lever to OFF

CHOKE by aligning lever with position

shown on decal (see illustration below). Al-

low the unit to run for 30 more seconds at

OFF CHOKE before releasing the throttle

trigger.

Choke

position

decal

STARTING A WARM ENGINE

1. Move ON/OFF switch to the ON position.

2. Move the choke lever to the HALF

CHOKE position.

3. Squeeze and hold the throttle trigger.

Keep throttle trigger fully squeezed until

the engine runs smoothly.

4. Pull starter rope sharply until engine runs.

but no more than 5 pulls.

5. Allow engine to run t5 seconds, then

movethe choke lever to the OFF CHOKE

position,

NOTE: If engine has not started, pull starter

rope 5 more pulls. If engine still does not run, it

is probably flooded.

STARTING A FLOODED ENGINE

Flooded engines can be started by placing

the choke lever in the OFF CHOKE position;

then, pull the rope to clear the engine of ex-

cess fuel. This could require pulling the starter

handle many times depending on how badly

the unit is flooded.

If the unit still doesn't start, refer to

TROUBLESHOOTING TABLE or call

1-800-554-6723.

OPERATING THE COUPLER

This model is equipped with a coupler which

enables optional attachments to be installed.

The optional attachments are: MODEL:

Edger ....................... PP1000E

Cultivator .................... PP2000T

Blower ...................... PP3000B

Brushcutter .................. PP4000C

i_ WARNING: Always stop unit and dis-

connect spark plug before removing or instal-

ling attachments.

REMOVING PRUNER ATTACH-

MENT, LINE TRIMMER ATTACH-

MENT, OR OTHER OPTIONAL AT-

TACHMENTS

CAUTION: When removing or installing at-

tachments, place the unit on a flat surface for

stability.

1. Loosen the coupler by turning the knob

counterclockwise.

Coupler

Lower \

Attachment

Upper Shaft

LOOSEN

TIGHTEN Knob

2. Press and hold the locking/release button.

Lower Attachment

3. While securely holding the engine and

upper shaft, pull the attachment straight

out of the coupler.

INSTALLING OPTIONAL ATTACH-

MENTS

1. Remove the shaft cap from the attach-

ment (if present).

2. Position locking/release button of attach-

ment into guide recess of coupler.

3. Push the attachment into the coupler until

the locking/release button snaps into the

primary hole.

4. Before using the unit. tighten the knob se-

curely by turning clockwise.

Coupler Primary Hole

Guide Recess

Upper Locking/ Attachment

Shaft Release

Button

aWARNING: Make sure the locking/

retease button is locked in the primary hole

and the knob is securely tightened before op-

erating the unit.

INSTALLING ATTACHMENT

HANGER

An attachment hanger is provided for storage

when attachment is not in use.

To install hanger on attachment:

1. Remove the shaft cap from the attach-

ment (if present) and discard.

2. Press and hold the locking/release button.

3. Push hanger onto the attachment until the

locking/release button snaps into the hole.

OPERATING INSTRUCTIONS

It is recommended that the engine not be

operated for longer than 1 minute at full

throttle.

OPERATING INSTRUCTIONS FOR

PRUNER ATTACHMENT

OPERATING POSITION

Head

Protection _,_ _

\ Eye

Long Pants Ii

g Pants

LUlLDANGER: Do not extend arms above

shoulders while pruning, Do not stand be-

neath branch being cut.

WARNING: Alwayswearhead,eye,

hearing, foot and body protection to reduce

the risk of injury when operating this unit,

When operating unit, clip shoulder strap onto

clamp, stand as shown and check for the fol-

lowing:

• Extend your left arm and hold assist handle

with your left hand.

• Hold throttle grip with your right hand with

finger on throttle trigger,

• Keep engine end below waist level.

• Keep shoulder strap pad centered on your

left shoulder and danger sign centered on

your back,

• Maintain full weight of tool on your left

shoulder.

Always release the throttle trigger and allow the

engine to return to idle speed when not pruning,

To stop engine:

• Release the throttle trigger,

• Move the ON/OFF switch to the OFF posi-

tion.

PRUNING

_'WARNING: Be alert for and guard

against kickback. Do not allow the moving

chain to contact any other branches or ob-

jects at the nose of the guide bar when prun-

ing, Allowing such contact can result in seri-

ous injury,

IMPORTANT POINTS

• Work slowly, keeping both hands firmty

gripped on the pruner. Maintain secure

footing and balance.

• Plan cut carefully. Check direction branch

will fall.

• Watch out for springpoles. Springpoles are

small size limbs which can catch the chain

and whip toward you or pull you off balance,

Use extreme caution when cutting small size

limbs or slender material.

• Watch out for branches immediately behind

the branch being pruned, if the chain hits the

rear branch, damage to tile unit may occur.

• Be alert for springback. Watch out for

branches that are bent or under pressure.

Avoid being struck by the branch or the

pruner when the tension in the wood fibers

is released.

• Keep a clear work area. Frequently clear

branches out of the way to avoid tripping

over them.

• Long branches should be removed in

several pieces.

PRUNING TECHNIQUE

When ready to cut, accelerate to full throttle

and apply a light cutting pressure. DO NOT

use back and forth sawing action.

'!i _1 Second cut

Third cut

Coil

First cut

Pruning technique

1. Make the first cut 6 inches (15 cm) from

the tree trunk on the bottom of the limb.

Use top of guide bar to make this cut. Cut

1/3 through the diameter of the limb.

NOTE: When making the second and third

cuts, rest the foot of the pruner against the

tree limb that is being cut to prevent whipping

of the branch.

2. Next, move 2 - 4 inches (5 - 10 cm) far-

ther out on the limb and make a second

cut all the way through the limb.

3. Then, make a final cut leaving a 1 - 2 inch

(2.5 - 5 cm) collar from the trunk of the

tree to avoid damage to the tree.

OPERATING INSTRUCTIONS FOR

TRIMMER ATTACHMENT

OPERATING POSITION

ALWAYS WEAR:

../_,!_ } Eye Protection

Long Pan_iti_,o

Heavy Shoes _._

Out from your right to your_l"eft.

AWARN ING: Alwaysweareye protec-

tion, Never lean over the trimmer head,

Rocks or debris can ricochet or be thrown into

eyes and face and cause blindness or other

serious injury,

Do not run the engine at a higher speed than

necessary. The cutting line will cut efficiently

when the engine is run at less than full throttle,

At lower speeds, there is less engine noise

and vibration, The cutting line will last longer

and wilt be less likely to "weld" onto the spool.

Always release the throttle trigger and allow

the engine to return to idle speed when not

cutting.

To stop engine:

• Release the throttle trigger,

• Move the ON/OFF switch to the OFF

position,

TRIMMER LINE ADVANCE

Thetrimmer line will advance approximately 2

inches (5 cm) each time the bottom of the

trimmer head is tapped on the ground with the

engine running at full throttle.

The most efficient line length is the maximum

length allowed by the line limiter.

Always keep the shield in place when the tool

is being operated.

To advance line:

• Operate the engine at full throttle.

• Hold the trimmer head parallel to and above

the grassy area.

• Tap the bottom of the trimmer head lightly on

the ground one time. Approximately 2 inches

(5 cm) of line will be advanced with each tap.

Always tap the trimmer head on a grassy

area. Tapping on surfaces such as concrete

or asphalt can cause excessive wear to the

trimmer head.

If the line is worn down to 2 inches (5 cm) or

less, more than one tap will be required to ob-

tain the most efficient line length.

WARNING: use only 0,080" (2 mm)

diameter line, Other sizes of line will not ad-

vance properly and can cause serious injury,

Do not use other materials such as wire,

string, rope, etc, Wire can break off during

cutting and become a dangerous missile that

call cause serious injury,

CUTTING METHODS

_WARNING: Use minimum speed

and do not crowd the line when cutting around

hard objects (rock, gravel, fence posts, etc.),

which can damage thetdmmer head, become

entangled in the tine, or be thrown causing a

serious hazard,

• The tip of the line does the cutting, You will

achieve the best performance and

mh_imum line wear by not crowding the line

into the cutting area, The right and wrong

wavs are shown below.

Tip of the Line I Line Crowded Into

Does The Cutting IWork Area

_?.:,

• The line will easily remove grass and

weeds from around walls, fences, trees and

flower beds, but it also can cut the tender

bark of trees or shrubs and scar fences.

• For trimming or scalping, use less than full

throttle to increase line life and decrease head

wear, especially:

• During light duty cutting.

• Near objects around which the line can

wrap such as small posts, trees or fence

wire,

• For mowing or sweeping, use full throttle for

a good clean job,

TRIMMING -Hotd the bottom of the trimmer

head about 3 inches (8 cm) above the ground

and at an angle, Allow only the tip of the line to

make contact, Do not force trimmer line into

work area,

Trimming . •.

\ ,

3 inches (8 cm) _" "_&_,_\

above ground ¥- _"Y_ '

SCALPING - The scalping technique re-

moves unwanted vegetation down to the

ground, Hotd the bottom of the trimmer head

about 3 inches (8 cm) above the ground and

at an angle. Allow the tip of the line to strike the

ground around trees, posts, monuments, etc.

This technique increases line wear.

Scalping .....

MOWING - Your trimmer is ideal for mowing

in places conventional lawn mowers cannot

reach. In the mowing position, keep the line

parallel to the ground. Avoid pressing the

head into the ground as this can scalp the

ground and damage the

tool,

Mowing HI

SWEEPING - The fanning action of the rotat-

ing line can be used for a quick and easy

clean up. Keep the line parallel to and above

the surfaces being swept and move the tool

from side to

side.

Swe_. .....

='%

wmWARNING: Disconnect the spark

plug before performing maintenance except

for carburetor adjustments.

HELPFUL TIP

IMPORTANT:Have all

f_1_b,_ repairs other than the rec-

I[ __ommended maintenance

[_a,_ ._.,_] described in the instruction

k_ l_Fy manual performed by an

authorized service dealer.

If any dealer other than an authorized

service dealer performs work on the

product, Electrolux Home Products,

Inc., may not pay for repairs under war-

ranty. It is your responsibility to maintain

and perform general maintenance.

CHECK FOR LOOSE

FASTENERS AND PARTS

• Spark Plug Boot

• Air Filter

• Housing Screws

• Assist Handle Screw

• Debris Shield

CHECK FOR DAMAGED OR

WORN PARTS

Contact an authorized service dealer for re-

placement of damaged or worn parts.

• ON/OFF switch - Ensure ON/OFF switch

functions properly by moving the switch to

the OFF position. Make sure engine stops;

then restart engine and continue.

• Fuel tank - Discontinue use of unit if fuel

tank shows signs of damage or leaks.

• Oil tank - Discontinue use of unit if oil tank

shows signs of damage or leaks.

• Debrisshield- Discontinueuseofunitifde-

bris shield is damaged.

INSPECT AND CLEAN UNIT AND LA-

BELS

• After each use. inspect complete unit for

loose or damaged parts. Clean the unit and

labels using a damp cloth with a mild deter-

gent.

• Wipe off unit with a clean dry cloth.

CHECK CHAIN TENSION

WARNING: Wear protective gloves

when handling chain. The chain is sharp and

can cut you even when it is not moving. Make

chain adjustments with lower end supported.

Chain tension is very important. Chains

stretch during use. This is especially true dur-

ing the first few times you use your pruner. Al-

ways check chain tension each time you use

and refuel your unit.

1. Use the screwdriver end of the chah_ ad-

justment tool (bar tool) to move chain

around guide bar to ensure kinks do not

exist. The chain should rotate freely.

Chain Adjustment Tool

Guide

Bar

2. Loosen bar clamp nut until it is finger tight

against the bar clamp.

Adjusting Screw Bar clamp nut

3. Turn adjusting screw clockwise until

chain solidly contacts bottom of guide bar

rail Then. turn adjusting screw an addi-

tional t/4 turn.

Adjusting Screw - 1/4 Turn

4. Using bar tooI. roll chain around guide bar

to ensure all links are in bar groove.

5. Lift up tip of guide bar to check for sag.

Release tip of guide bar, then turn adjust-

ing screw 1/4 turn clockwise. Repeat until

sag does not exist.

6. While lifting tip of guide bar. tighten bar

clamp nut securely with the bar tool.

7. Use the screwdriver end of the bar tool to

move chain around guide bar.

8. If chain does not rotate, it is too tight.

Slightly loosen bar clamp nut and loosen

chain by turning the adjusting screw 1/4

turn counterclockwise. Retighten bar

clamp nut.

9. If chain is too loose, it will sag below the

guide bar and needs to be tightened fol-

lowing above procedure.

'4;_,WARNING: DO NOT operate the

pruner ifthe chain is loose. Ifthe pruner is oper-

ated with a loose chain, the chain could jump off

the guide bar and result in serious injury.

CHECK CHAIN SHARPNESS

A sharp chain makes wood chips. A dull chain

makes a sawdust powder and cuts slowly.

See CHAIN SHARPENING in the SERVICE

AND ADJUSTMENTS section.

CLEAN AIR FILTER

A dirty air filter decreases engine perform-

ance and increases fuel consumption and

harmful emissions. Always clean after every

5 hours of operation.

1. Clean the cover and the area around itto

keep dirt from falling into the carburetor

chamber when the cover is removed.

2. Remove parts by pressing button to re-

_ease air filter cover.

NOTE: To avoid creating a fire hazard or

producing harmful evaporative emissions, do

not clean filter in gasoline or other flammable

solvent.

3. Wash the filter in soap and water.

4. Allow filter to dry.

5. Replace parts.

Button _-_ Air Filter

_4_ Air Filter

"_ __-'_ _ Cover

BAR MAINTENANCE

If your pruner cuts to one side, has to be

forced through the cut, or been run with an im-

proper amount of bar lubrication it may be

necessary to service your bar. A worn bar will

damage your chain and make cutting difficult.

After each use. ensure ON/OFF switch is in

the OFF position, then clean all sawdust from

the guide bar and sprocket hole.

To maintain guide bar:

• Move ON/OFF switch to the OFF position

and disconnect spark plug.

• Loosen and remove bar clamp nut and

chain brake. Remove bar and chain from

pruner.

• Clean the oil holes and bar groove after

each 5 hours of operation.

Remove Sawdust From

Guide Bar Groove

Oil Holes

• Burring of guide bar rails is a normal

process of rail wear. Remove these burrs

with a fiat file.

• When rail top is uneven, use a flat file to

restore square edges and sides.

_1"_ File Rail Edges_r] r]

and Sides I U I

square I I

Worn Groove Correct Groove

Replace guide bar when the groove is worn,

the guide bar is bent or cracked, or when

excess heating or burring ofthe rails occurs. If

replacement is necessary, use only the guide

bar specified for your pruner in the repair

parts list.

LUBRICATION

FillCap

• See GUIDE BAR AND CHAIN OIL under

the OPERATION section.

MUFFLER AND SPARK ARREST-

ING SCREEN

_& WARNING: Themuffleronthisprod-

uctcontains chemicals known to the State of

California to cause cancer,

As your unit is used, carbon deposits build up

on the muffler and spark arresting screen,

For normal homeowner use, however, the

muffler and spark arresting screen will not re-

quire any service. After 50 hours of use, we

recommend that your muffler be serviced or

replaced by your authorized service dealer.

REPLACE SPARK PLUG

Replace the spark plug each year to ensure

the engine starts easier and runs better. Set

spark plug gap at 0.025 inch (0,6 mm). Igni-

tion timing is fixed and nonadjustaMe,

1. Twist, then pull off spark plug boot,

2. Remove spark plug from cylinder and

discard.

3. Replace with Champion RCJ-6Y spark

plug and tighten securely with a 3/4 inch

(19 mm) socket wrench.

4. Reinstall the spark plug boot.

,t=

r=WARNING: Disconnect the spark

plug before performing maintenance, service, or

adjustments except for carburetor adjustments.

CHAIN SHARPENING

Chah_ sharpening is a complicated task that

requires special tools. We recommended you

refer chain sharpening to a professional chain

sharpener.

CHAIN REPLACEMENT

WARNING: Wear protective gloves

when handling chain, The chain is sharp and

can cut you even when it is not moving,

It is normal for a new chain to stretch during the

first 15 minutes of operation. You should re-

check your chain tension frequently and adjust

the chain tension as required, See CHAIN TEN-

SION section,

Replace the old chain when it becomes worn or

damaged. Use only the Low-Kickback replace-

ment chain specified in the repair parts list.

TO REPLACE CHAIN:

1. Move ON/OFF switch to the OFF position

and disconnect spark plug.

2. Remove bar clamp nut.

3. Remove bar clamp.

4. Turn adjusting screw by hand counter-

clockwise until adjusting pin just touches

the stop.

5. Slide guide bar behind sprocket until

guide bar stops against sprocket.

6. Remove the old chain.

7. Carefully remove new chain from pack-

age. Hold chain with the drive links as

shown.

Tip of

Bar

CUTTERS MUST FACEff /1

DIRECTION OF ROTATION

Cutters Depth Gauge

" Drive Links

8. Place chain over sprocket, fitting the

drive links in the sprocket.

9. Fit bottom of drive Nnks between the teeth

in the sprocket in the nose of the guide

bar.

10. Fit chain drive links into bar groove.

11. Pull guide bar forward until chain is snug

in guide bar groove. Ensure all drive links

are in the bar groove.

12. Now, instaN bar clamp making sure the

adjusting pin is positioned in the lower

hole in the guide bar.

Lower

Hole

Adjust_ Pin _

13. Install bar clamp nut and finger tighten

only. Do not tighten any further at this

point. Proceed to the CHAIN ADJUST-

MENT section.

CHAIN ADJUSTMENT

See CHECK CHAIN TENSION in MAINTE-

NANCE section.

REPLACING THE LINE

1. Remove spool by firmly pulling on tap

button.

2. Clean entire surface of hub and spool.

3. Replace with a pre-wound spool, or cut two

lengths of 12-1/2 feet of 0>080" (2 mm) di-

ameter Poulan PRO ¢ brand line.

&WARNING: Never use wire. rope,

string, etc.. which can break offand become a

dangerous missile.

4. Insert ends of the lines about 1/2 inch (1

cm) into the small holes on the inside of

spool.

Spool

if _/_ Holes

5¢7Y

b//1,_ ,

Line exit holes Line in Notch

,' Hub I in_ in Nrff_h

5. Wind the line evenly and tightly onto the

spool. Wind in the direction of the arrows

found on the spool.

6. Push the lines into the notches, leaving 3

to 5 inches (7 - 12 cm) unwound.

7. Insert the lines into the the exit holes in

the hub as shown in the illustration.

8. Align the notches with the line exit holes.

9. Push spool into hub until itsnaps into place.

10. PuN the lines extending outside of the hub

to release the lines from the notches.

CARBURETOR ADJUSTMENT

WARNING: Keepothers away when

making idle speed adjustments. The chain

will be moving during most of this procedure.

Wear your protective equipment and observe

all safety precautions. After making adjust-

ments, the chain must not move at idle speed.

The carburetor has been carefully set at the

factory. Adjustment to the idle speed may be

necessary if you notice any of the following

conditions:

•Engine will not idle when the throttle is re-

leased.

• The chain moves at idle.

Make adjustments with the unit supported so

the pruner is off the ground and the chain will

not make contact with any object. Hold the

unit by hand while running and making adjust-

ments. Keep all parts of your body away from

the chain and muffler.

Idle Speed Screw

IDLE SPEED ADJUSTMENT

Allow engine to idle>Adjust idle speed until en-

gine runs without chain moving (idle too fast)

or stalNng (idle speed too slow).

• Turn idle speed screw clockwise to in-

crease engine speed if engine stalls or dies.

• Turn idle speed screw counterclockwise to

decrease engine speed if chain moves at idle.

_WARNING: Recheck the idle speed

after each adjustment. The chain must not

move at idle speed to avoid serious injury to

the operator or others.

if you require further assistance or are unsure

about performing this procedure, contact your

authorized service dealer or call

1-800-554-6723.

4_W/-_I'iNIN_: Perform the following

steps after each use:

• Allow engine to cool before storing or trans-

porting.

• Store unit and fuel h_awell ventilated area

where fuel vapors cannot reach sparks or

open flames from water heaters, electric

motors or switches, furnaces, etc.

• Store unit with all guards in place. Position

unit so that any sharp object cannot acci-

dentally cause injury.

• Store unit and fuel well out of the reach of

children.

SEASONAL STORAGE

Prepare unit for storage at end of season or if

it will not be used for 30 days or more.

If your unit is to be stored for a period of time:

• Clean the entire unit before lengthy

storage.

• Store in a clean dry area.

• Lightly oil external metal surfaces.

FUEL SYSTEM

Under FUELING ENGINE in the OPERA-

TION section of this manual, see message la-

beled IMPORTANT regarding the use of ga-

sohol in your engine.

Fuel stabilizer is an acceptable alternative in

minimizing the formation of fuel gum deposits

during storage. Add stabilizer to the gasoline

in the fuel tank or fuel storage container. PoF

low the mix instructions found on stabilizer

container. Run engine at least 5 minutes after

adding stabilizer.

HELPFUL TIP I

During storage of your gas/ I

f_J_/J_'X oitmixture theoilwillsepa- I

_z_lF_.i_ rate from the gas. I

V_ImI_W) We recommend that you I

_J shake the gas can weekly I

to insure proper blending of I

the gas and oil. I

ENGINE

•Remove spark plug and pour 1 teaspoon of

40:1,2-cycle engine oil (air cooled) through

the spark plug opening. Slowly pull the

starter rope 8 to 10 times to distribute oil.

• Replace spark plug with new one of recom-

mended type and heat range.

• Clean air filter.

• Check entire unit for loose screws, nuts,

and bolts. Replace any damaged, broken,

or worn parts.

• At the beginning of the next season, use

only fresh fuel having the proper gasoline to

oil ratio.

OTHER

• Do not store gasoline from one season to

another.

• Replace your gasoline can if itstarts to rust.

TROUBLESHOOTING TABLE

,_, WAR NIN G: Always stop unit and disconnect spark plug before performing all of the

recommended remedies below except remedies that require operation of the unit.

TROUBLE

Engine will not

start.

CAUSE REMEDY

1. Move ON/OFF switch to ON.

1. ON/OFF switch in

OFF position.

2. Engine flooded.

3. Fuel tank empty.

4. Spark plug not firing.

5. Fuel not reaching

carburetor.

6. Carburetor requires

adjustment.

Engine wilt 1. Idle speed set too high

not idle or too low.

properly. 2. Crankshaft seals worn.

3. Compression low.

1. Air filter dirty.

2. Spark plug fouled.

Engine will not

accelerate,

lacks power.

or dies under

a load.

Engine

smokes

excessively.

3. Carburetor requires

adjustment.

4. Carbon build-up on

muffter outIet screen.

5. Compression low.

1. Choke partially on.

2. Fuel mixture incorrect.

2. See "Starting a Flooded Engine" in

Operation Section.

3. Fill tank with correct fuel mixture.

4. Install new spark plug.

5. Check for dirty fuel filter; replace.

Check for kinked or split fuel line;

repair or replace.

6. Contact an authorized service dealer.

1. See "Carburetor Adjustment" in

Service and Adjustments Section.

2. Contact an authorized service dealer.

3. Contact an authorized service dealer.

1. Clean or replace air filter.

2. Clean or replace plug

and regap.

3. Contact an authorized service dealer.

4. Contact an authorized service dealer.

5. Contact an authorized service dealer.

1. Adjust choke.

2. Empty fuel tank and refill with

correct fuel mixture.

3. Clean or replace air filter.

4. Contact an authorized service dealer.

3. Air filter dirty.

4. Carburetor requires

adjustment.

Engine runs 1. Fuel mixture incorrect. 1. See "Fueling Engine" in Operation

hot. section.

2. Spark plug incorrect. 2. Replace with correct spark plug.

3. Carburetor requires 3. Contact an authorized service dealer.

adjustment.

4. Carbon build-up on 4. Contact an authorized service dealer.

muffler outlet screen.

Chain moves at 1. Idle speed requires 1. See "Carburetor Adjustment" in

idle speed, adjustment. Service and Adjustments Section.

2. Clutch requires repair. 2. Contact an authorized service dealer.

ELECTROLUX HOME PRODUCTS, INC.,

warrants to the original purchaser that each

new Poulan PRO ® brand gasoline tool or at-

tachment is free from defects in material and

workmanship and agrees to repair or replace

under this warranty any defective gasoline

product or attachment as follows from the

original date of purchase.

2 YEARS - Parts and Labor, when used for

household purposes.

90 DAYS - Parts and Labor, when used for

commercial, professional, or income produc-

ing purposes.

30 DAYS - Parts and Labor, if used for rental

purposes.

This warranty is not transferable and does not

cover damage or liability caused by improper

handlh_g, improper mah_tenance, or the use

of accessories and/or attachments not spe-

cifically recommended by ELECTROLUX

HOME PRODUCTS, INC., for this tool. Addi-

tionally, this warranty does not cover tune-

ups, spark plugs, filters, cutting line, or rotat-

ing head parts that will wear and require

repIacement with reasonable use during the

warranty period. This warranty does not cov-

er predelivery setup or normal adjustments

explained in the instruction manual.

THiS WARRANTY GIVES YOU SPECIFIC

LEGAL RIGHTS, AND YOU MAY HAVE

OTHER RIGHTS WHICH VARY FROM

STATE TO STATE.

NO CLAIMS FOR CONSEQUENTIAL OR

OTHER DAMAGES WiLL BE ALLOWED,

AND THERE ARE NO OTHER EXPRESS

WARRANTIES EXCEPT THOSE EX-

PRESSLY STIPULATED HEREIN.

SOME STATES DO NOT ALLOW LiMiTA-

TIONS ON HOW LONG AN IMPLIED WAR-

RANTY LASTS OR THE EXCLUSION OR

LIMITATIONS OF INCIDENTAL OR CON-

SEQUENTIAL DAMAGES, SO THE ABOVE

LIMITATIONS OR EXCLUSION MAY NOT

APPLY TO YOU.

The policy of ELEOTROLUX HOME PROD-

UOTS, INO., is to continuously improve its

products. Therefore, ELEOTROLUX HOME

PRODUCTS, INC., reserves the right to

change, modify, or discontinue models, de-

signs, specifications, and accessories of all

products at any time without notice or obliga-

tion to any purchaser.

YOUR WARRANTY RIGHTS AND OB-

LIGATIONS: The U.S. Environmental

Protection Agency, California Air Resources

Board, Environment Canada and ELECTRO-

LUX HOME PRODUCTS, INC., are pleased

to explain the emissions control system war-

ranty on your year 2005 and later small off-

road engine, in California, all small off-road

engines must be designed, built, and

equipped to meet the State's stringent anti-

smog standards. ELECTROLUX HOME

PRODUCTS, INC., must warrant the emis-

sion control system on your small off-road

engine for the periods of time listed below pro-

vided there has been no abuse, neglect, or

improper maintenance of your small off-road

engine. Your emission control system in-

cludes parts such as the carburetor and the

ignition system. Where a warrantable condi-

tion exists, ELECTROLUX HOME PROD-

UCTS, INC., will repair your small off-road

engine at no cost to you. Expenses covered

under warranty include diagnosis, parts and

labor. MANUFACTURER'S WARRANTY

COVERAGE: if any emissions related part

on your engine (as listed under Emissions

Control Warranty Parts List) is defective or a

defect in the materials or workmanship of the

engine causes the failure of such an emission

related part, the part wilt be repaired or re-

placed by ELECTROLUX HOME PROD-

UCTS, iNC. OWNER'S WARRANTY RE-

SPONSIBILITIES: As the small off-road

engine owner, you are responsible for the per-

formance of the required maintenance listed

in your instruction manual. ELECTROLUX

HOME PRODUCTS, INC., recommends that

you retain all receipts covering maintenance

on your small off-road engine, but ELEC-

TROLUX HOME PRODUCTS, iNC., cannot

deny warranty solely for the lack of receipts or

for your failure to ensure the performance of

all scheduled maintenance. As the small off-

road engine owner, you should be aware that

ELECTROLUX HOME PRODUCTS, iNC.,

may deny you warranty coverage if your

small off- road engine or a part of it has failed

due to abuse, neglect, improper mainte-

nance, unapproved modifications, or the use

of parts not made or approved by the original

equipment manufacturer. You are responsi-

ble for presenting your small off-road engine

to an ELECTROLUX HOME PRODUCTS,

INC., authorized repair center as soon as a

problem exists. Warranty repairs should be

completed in a reasonable amount of time,

not to exceed 30 days. If you have any ques-

tions regarding your warranty rights and re-

sponsibilities, you should contact your near-

est authorized service center or call

ELECTROLUX HOME PRODUCTS, INC., at

1-800-554-6723. WARRANTY COM-

MENCEMENT DATE: The warranty period

begins on the date the small off-road engine

is purchased. LENGTH OF COVERAGE:

This warranty shall be for a period of two

years from the initial date of purchase. WHAT

IS COVERED: REPAIR OR REPLACE-

La page charge ...

Poulan Pro PP446T Manuel utilisateur

Marque: Poulan Pro

Modèle: PP446T

Catégorie: Mini motoculteurs

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Poulan Pro PP446T User manual
español: Poulan Pro PP446T Manual de usuario

Poulan Pro PP446T Manuel utilisateur

Poulan Pro PP446T Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents