RIDGID 1000RSDS Manuel utilisateur
- Catégorie
- Pistolets à chaleur
- Taper
- Manuel utilisateur
Ce manuel convient également à
PUMP SPECIFICATIONS
POWER SUPPLY REQUIREMENTS 120 V, 60 Hz
MOTOR Single Phase, Dielectric Oil Filled
HORSEPOWER
1 HP ....................
CIRCUIT REQUIREMENTS 15 A (minimum)
DIMENSIONS
11-1/2 in. high x 9-3/4 in. base
ON LEVEL (FACTORY SET) Approximately 9.5 in.
OFF LEVEL (FACTORY SET)
Approximately 4.5 in.
Smart Submersible Sump Pump
Please read and save these instructions. Read carefully before attempting to assemble, install,
operate or maintain the product described. Protect yourself and others by observing all safety
information. Failure to comply with instructions could result in personal injury and/or property
damage! Retain instructions for future reference.
Installation Manual 1000RSDSSmart
PERFORMANCE GAL/HR
Model HP Discharge Head (Lift Distance)
0 ft 5 ft 10 ft 15 ft 20 ft
1000RSDSSmart 1 6600 6240 5640 4920 3660
600007-001 B 04/21© 2021, RIDGID® TOOL COMPANY www.homedepot.com
CONSTRUCTION
MOTOR HOUSING Stainless Steel
VOLUTE Cast Iron
IMPELLER
Glass Reinforced Thermoplastic
SHAFT Steel
DISCHARGE
1-1/2 in. NPT
CONTROLLER SPECIFICATIONS
SWITCH Solid State Air Switch
CONNECTIVITY Wi-Fi + BLE
AIR TUBE
PVC
INSTALLATION MANUAL
2
SAFETY SIGNAL WORDS
This manual contains information that is very important
to know and understand. This information is provided for
SAFETY and to PREVENT EQUIPMENT PROBLEMS. To
help recognize this information, observe all safety information
labeled danger, warning, caution, and notice.
SUMP PUMP DESCRIPTION
Sump pumps are automatic pumps used to remove ground water from
sump pits. The most common application is for basement drainage to
prevent flooding in residential buildings. These pumps are designed to
pump clear water only. With the innovative and reliable Air Switch, your
pump is no longer limited by the mechanical cycles of traditional float switch
style pumps. The integrated controller and companion app for your iOS or
Android device keeps you informed of the status of your pump; informing
you whenever there is a problem and your basement is no longer protected.
These pumps are not designed to be used with a portable generator.
Installation of this pump outdoors, unprotected from the weather, may
cause hazardous conditions and will void warranty. Water inside the pump
may freeze, limiting its performance and damaging the pump and pipes.
UNPACKING
Inspect this unit before it is used. Occasionally, products are damaged
during shipment. If the pump or components are damaged, return the
unit to the place of purchase for replacement, or call Customer Support
(1-877-9RIDGID®).
Intended for Indoor Use Only
PLEASE SEE WWW.RIDGID® PUMPS.COM FOR PRODUCT INFORMATION AND INSTALLATION VIDEOS
This pump is not designed to handle salt water, brine, laundry
discharge, water softener, sewage, grey water, or any other
application which may contain caustic chemicals and/or
foreign materials. Pump and/or property damage could occur
if used in these applications and will void warranty.
FOR ADDED SAFETY the receptacle must be protected with a ground
fault circuit interrupter (GFCI). All wiring must be performed by a
qualified licensed electrician and comply with the National Electric
Code and all applicable local codes and ordinances.
POUR PLUS DE SÉCURITÉ, la prise de courant doit être protégée par
un disjoncteur de fuite à la terre. Tout le câblage doit être effectué
par un électricien qualifié et être conforme au Code électrique
national et à tous les codes et règlements locaux applicables.
NEVER REMOVE THE GROUND PRONG from the plug or bypass the
grounding wires.
NE JAMAIS RETIRER LE CONNECTEUR DE MISE À LA TERRE de la prise
ou contourner les fils de mise à la terre.
MAKE SURE THE POWER SUPPLY HAS A FUSE OR CIRCUIT BREAKER
rated to handle the current (amps) noted on the pump nameplate
or cord tag.
S’ASSURER QUE L’ALIMENTATION ÉLECTRIQUE EST MUNIE D’UN
FUSIBLE OU D’UN DISJONCTEUR d’une valeur nominale appropriée
pour supporter l’intensité du courant (ampérage) indiquée sur la
plaque signalétique ou l’étiquette du cordon de la pompe.
DO NOT REMOVE POWER SUPPLY CORD and strain relief or connect
conduit directly to the pump.
NE PAS RETIRER LE CORDON D’ALIMENTATION ÉLECTRIQUE et le
réducteur de tension, ni connecter le conduit directement à la
pompe.
ALWAYS DISCONNECT THE PUMP from power supply before installing,
servicing or making any adjustments.
TOUJOURS METTRE LA POMPE HORS TENSION avant de procéder à
l’installation, à l’entretien ou à des réglages.
DO NOT WALK on the floor when water is present until all power is
turned off. If the electric panel is in the basement, call an electrician.
NE PAS MARCHER sur un sol mouillé avant que l’alimentation
générale ne soit coupée. Si le tableau électrique est en sous-sol,
appeler un électricien.
IMPORTANT SAFETY INFORMATION
CONSIGNES DE SÉCURITÉ
IMPORTANTES
WARNING INDICATES A POTENTIALLY HAZARDOUS SITUATION
WHICH, IF NOT AVOIDED, COULD RESULT IN DEATH OR
SERIOUS INJURY.
LA MENTION AVERTISSEMENT INDIQUE UNE SITUATION
POTENTIELLEMENT DANGEREUSE QUI, SI ELLE N’EST PAS
ÉVITÉE, RISQUE D’ENTRAÎNER DES LÉSIONS CORPORELLES
GRAVES OU MÊME LA MORT.
RISK OF ELECTRIC SHOCK. TO REDUCE THIS RISK,
OBSERVE THE FOLLOWING WARNINGS:
RISQUE DE CHOC ÉLECTRIQUE. POUR RÉDUIRE CE
RISQUE, TENIR COMPTE DES AVERTISSEMENTS
SUIVANTS
MAKE SURE THERE IS A PROPERLY GROUNDED RECEPTACLE
AVAILABLE. This pump is supplied with a grounding conductor
and grounding-type attachment plug. To reduce the risk of electric
shock, be certain that it is connected only to a properly grounded,
grounding-type receptacle.
S’ASSURER QU’UNE PRISE DE MISE À LA TERRE EST DISPONIBLE.
Cette pompe est fournie avec un conducteur et une fiche de mise à
la terre. Pour réduire le risque de choc électrique, s’assurer qu’elle
est branchée seulement à une prise de courant correctement mise
à la terre.
INSTALLATION MANUAL
3
NEVER HANDLE A PUMP or motor with wet hands or when standing
on a wet or damp floor while the pump is plugged into the power
supply.
NE JAMAIS MANIPULER UNE POMPE ou un moteur de pompe avec
les mains mouillées ou debout dans l’eau ou sur une surface
humide.
RISK OF ELECTRIC SHOCK. This pump has not been investigated for
use in swimming pool and marine areas.
RISQUE DE CHOC ÉLECTRIQUE. Cette pompe n’a pas fait l’objet
de vérification pour une utilisation dans les piscines et les aires
marines.
DO NOT USE TO PUMP FLAMMABLE OR EXPLOSIVE FLUIDS such as
gasoline, fuel oil, kerosene, etc. Do not use in a flammable and/or
explosive atmosphere. Pump should only be used to pump clear
water. Personal injury and/or property damage will result and void
warranty.
NE PAS UTILISER POUR POMPER DES FLUIDES INFLAMMABLES OU
EXPLOSIFS tels que l’essence, le mazout, le kérosène, etc. Ne
pas utiliser dans un environnement inflammable et/ou explosif.
La pompe ne doit être utilisée que pour pomper de l’eau claire.
Des blessures corporelles et/ou des dégâts matériels pourraient
en résulter.
PUMPS ARE NOT DESIGNED TO TRANSFER WATER INTENDED FOR
DRINKING. Do not use the pump for moving water that will be
used for potable/drinking water. Pump should only be used in
applications for which it is designed.
LES POMPES NE SONT PAS CONÇUES POUR L’ACHEMINEMENT
D’EAU DESTINÉE À LA CONSOMMATION. Ne pas utiliser la pompe
pour transporter de l’eau qui sera utilisée comme de l’eau
potable/destinée à la consommation. La pompe doit être utilisée
uniquement dans les applications pour lesquelles elle est conçue.
DO NOT USE AN EXTENSION CORD OR SURGE PROTECTOR. Extension
cords and/or surge protectors could present a safety hazard if not
sized properly, become damaged or the connection falls into the
sump. If receptacle is not within reach of the pump’s power cord,
contact a qualified licensed electrician to install a new receptacle.
NE PAS UTILISER DE RALLONGE NI DE PROTECTEUR DE SURTENSION.
Les rallonges et/ou les protecteurs de surtension peuvent présenter
un danger pour la sécurité s’ils ne sont pas correctement calibrés,
s’ils sont endommagés ou si le raccordement tombe dans le
puisard. Si la prise n’est pas à portée du cordon d’alimentation
de la pompe, contacter un électricien qualifié pour installer une
nouvelle prise.
CAUTION INDICATES A POTENTIALLY HAZARDOUS SITUATION
WHICH, IF NOT AVOIDED, MAY RESULT IN MINOR OR
MODERATE INJURY.
MISE EN GARDE
LA MENTION MISE EN GARDE INDIQUE UNE SITUATION
POTENTIELLEMENT DANGEREUSE QUI, SI ELLE N’EST PAS
ÉVITÉE, POURRAIT ENTRAÎNER DES BLESSURES MINEURES
OU MODÉRÉES.
TO REDUCE THE RISK OF HAZARDS THAT CAN CAUSE
INJURY OR PROPERTY DAMAGE, OBSERVE THE FOLLOWING
WARNINGS:
POUR RÉDUIRE LE RISQUE DE DANGERS POUVANT CAUSER
DES BLESSURES OU DES DÉGÂTS MATÉRIELS, RESPECTER
LES MISES EN GARDE SUIVANTES :
IT IS THE INSTALLER’S RESPONSIBILITY TO MAKE SURE THE
PUMPS AUTOMATIC SWITCH IS ABLE TO OPERATE WITHOUT ANY
OBSTRUCTIONS WITHIN THE BASIN. It is recommended that the
installer test and observe the pump’s operation for several cycles
after installation.
IL EST DE LA RESPONSABILITÉ DE L’INSTALLATEUR DE S’ASSURER QUE
L’INTERRUPTEUR AUTOMATIQUE DE POMPE PEUT FONCTIONNER SANS
AUCUN BLOCAGE À L’INTÉRIEUR DU SYSTÈME. Il est recommandé
que l’installateur teste et observe le fonctionnement de la pompe
pendant plusieurs cycles après l’installation.
IT IS REQUIRED TO USE RIGID PIPING AND FITTINGS to secure the
pump in the basin and reduce pump movement. Pump movement
can prevent the switch from operating correctly. Do not use flexible
hosing.
IL EST NÉCESSAIRE D’UTILISER DES TUYAUX ET DES RACCORDS
RIGIDES pour fixer la pompe dans le système et réduire les
mouvements de la pompe. Les mouvements de la pompe peuvent
empêcher l’interrupteur de fonctionner correctement. Ne pas
utiliser de tuyaux flexibles.
IT IS REQUIRED TO USE A CHECK VALVE with this pump to prevent the
back-flow of clear ground water after each pump cycle.
NÉCESSITE L’UTILISATION D’UNE VANNE DE CONTRÔLE cette pompe
pour empêcher le reflux d’eau souterraine claire après chaque
cycle de pompage.
DO NOT INSTALL OR OPERATE THE PUMP IF IT HAS BEEN DAMAGED
IN ANY WAY.
NE PAS INSTALLER OU FAIRE FONCTIONNER LA POMPE SI ELLE A ÉTÉ
ENDOMMAGÉE DE QUELQUE MANIÈRE QUE CE SOIT.
DO NOT LIFT OR CARRY THE PUMP BY THE POWER CORD OR AIR TUBE.
Use the pump’s handle or lift ring.
NE PAS SOULEVER OU PORTER LA POMPE PAR LE CORDON
D’ALIMENTATION O TUBO DE AIRE. Utiliser la poignée ou la bague de
levage de la pompe.
4
INSTALLATION MANUAL
DO NOT USE THIS PUMP IN MUD, SAND, CEMENT, OIL CHEMICALS,
GREY WATER, OR ANY OTHER WATER THAT IS NOT CLEAR GROUND
WATER.
NE PAS UTILISER CETTE POMPE DANS LA BOUE, LE SABLE, LE CIMENT,
LES PRODUITS CHIMIQUES À L’HUILE, DE L’EAU GRISÂTRE OU TOUTE
AUTRE EAU QUI N’EST PAS DE L’EAU CLAIRE SOUTERRAINE.
DO NOT USE SUMP PUMPS TO HANDLE RAW SEWAGE.
NE PAS UTILISER DE POMPES DE PUISARD POUR POMPER LES
EFFLUENTS.
AN INDEPENDENT HIGH WATER ALARM OR BACK UP PUMP SHOULD BE
USED when risk of property damage from high water levels exists.
UNE ALARME AUTONOME DE NIVEAU D’EAU ÉLEVÉ OU UNE POMPE DE
SAUVEGARDE DOIVENT ÊTRE UTILISÉES en cas de risque de dégâts
matériels causés par des niveaux d’eau élevés.
This product can expose you to chemicals, including DEHP,
which is known to the State of California to cause cancer, birth
defects and reproductive harm. For more information, go to
www.P65Warnings.ca.gov.
Ce produit peut vous exposer à des produits chimiques,
notamment du DOP, reconnus par l’État de Californie comme
étant cancérigènes et à l’origine d’anomalies congénitales et de
problèmes de l’appareil reproductif. Pour plus de renseignements,
visiter le site www.P65Warnings.ca.gov.
AIR SWITCH This Air Switch is not adjustable. Any modifications or
alterations will void the warranty and/or cause premature failure of
the pump, which could lead to property damage.
INTERRUPTEUR À AIRE VERTICAL. Ce aire n’est pas réglable.
Toute modification ou altération peut entraîner une défaillance
prématurée de la pompe avec pour conséquences des risques
de dégâts matériels. Ces modifications ou altérations annuleront
la garantie du matériel.
FCC INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to connect
the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions.
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by the party
responsible for compliance could voice the user’s authority to
operate the equipment.
RF EXPOSURE
To comply with FCC/IC RF exposure requirements for mobile
transmitting devices, this transmitter should only be used or
installed at locations where there is at least 20 cm separation
distance between the antenna and all persons.
Under Industry Canada regulations, this radio transmitter may
only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce
potential radio interference to other users, the antenna type and its
gain should be so chosen that the equivalent isotropically radiated
power (e.i.r.p.) is not more than that necessary for successful
communication.
This Device complies with Industry Canada License-exempt RSS
standards(s). Operation is subject to the following two conditions:
1) this device may not cause interference, and 2) this device must
accept any interference, including interference that may cause
undesired operation of the device.
MISE EN GARDE
INSTALLATION MANUAL
5
DECLARACIÓN SOBRE INTERFERENCIAS DE LA FCC
Este equipo ha sido probado y se ha comprobado que cumple con
los límites de un dispositivo digital de clase B, de acuerdo con la
sección 15 de las normas de la FCC. Estos límites están diseñados
para proporcionar una protección razonable contra interferencias
perjudiciales en una instalación residencial. Este equipo genera,
usa y puede irradiar energía de radiofrecuencia y, si no se instala y
usa de acuerdo con las instrucciones, puede causar interferencias
perjudiciales a las comunicaciones por radio. No obstante, no
se puede garantizar que no se produzcan interferencias en
una instalación en particular. Si este equipo causa interferencia
perjudicial en la recepción de radio o televisión, lo cual se puede
determinar encendiendo y apagando el equipo, se recomienda al
usuario que intente conectar la interferencia mediante una de las
siguientes medidas:
- Reorientar o reubicar la antena receptora.
- Aumentar la separación entre el equipo y el receptor.
- Conectar el equipo a una toma de corriente de un circuito
diferente al que está conectado el receptor.
- Consultar con el distribuidor o con un técnico de radio/TV
experimentado para obtener ayuda.
Este dispositivo cumple con la sección 15 de las normas de la FCC.
El funcionamiento está sujeto a las dos condiciones siguientes.
1. Es posible que este dispositivo no cause interferencias
perjudiciales, y
2. Este dispositivo debe aceptar cualquier interferencia recibida,
incluida la interferencia que pueda causar un funcionamiento no
deseado.
Los cambios o modificaciones que no hayan sido explícitamente
aprobados por la parte responsable del cumplimiento podrían
anular la autoridad del usuario para utilizar el equipo.
EXPOSICIÓN A RF
Para cumplir con los requisitos de exposición a RF de la FCC/IC
para dispositivos de transmisión móviles, este transmisor solo se
debe usar o instalar en lugares donde haya al menos 20 cm de
distancia de separación entre la antena y todas las personas.
Según las reglamentaciones de Industry Canada, este transmisor
de radio solo puede funcionar con una antena de un tipo y una
ganancia máxima (o menor) aprobada para el transmisor por
Industry Canada. Para reducir las posibles interferencias de radio
a otros usuarios, el tipo de antena y su ganancia se deben elegir
de manera que la potencia isotrópica radiada equivalente (p.i.r.e.)
no sea mayor que la necesaria para una comunicación exitosa.
Este dispositivo cumple con los estándares RSS exentos de
licencia de Industry Canada. El funcionamiento está sujeto a las
dos condiciones siguientes: 1) este dispositivo no puede causar
interferencias, y 2) este dispositivo debe aceptar cualquier
interferencia, incluidas las interferencias que puedan causar un
funcionamiento no deseado del dispositivo.
DÉCLARATION D’INTERFÉRENCE DE LA FCC
Cet équipement a été testé et jugé conforme aux limites d’un
appareil numérique de classe B, conformément à la partie 15
des règles de la FCC. Ces limites sont conçues pour fournir une
protection raisonnable contre les interférences nuisibles dans une
installation résidentielle. Cet équipement génère, utilise et peut
émettre une énergie de radiofréquence et, si non installé et utilisé
conformément aux instructions, peut causer des interférences
nuisibles aux communications radio. Cependant, il n’y a aucune
garantie que l’interférence ne se produira pas dans une installation
particulière. Si cet équipement cause des interférences nuisibles à
la réception radio ou télévisuelle, qui peuvent être déterminées en
éteignant et en allumant l’équipement, l’utilisateur est encouragé
à essayer de connecter les interférences par l’une des mesures
suivantes :
- Réorienter ou déplacer l’antenne de réception.
- Augmenter la distance entre l’équipement et le récepteur.
- Brancher l’équipement dans une prise sur un circuit différent de
celui auquel le récepteur est connecté.
- Consulter le revendeur ou un technicien radio/TV expérimenté
pour obtenir de l’aide.
Cet appareil est conforme à la partie 15 des règles de la FCC.
L’exploitation est soumise aux deux conditions suivantes.
1. Ce dispositif peut ne pas causer d’interférences nuisibles, et
2. Ce dispositif doit accepter toute interférence reçue, y compris
toute interférence susceptible de provoquer un fonctionnement
indésirable.
Les changements ou les modifications qui ne sont pas expressément
approuvés par la partie responsable de la conformité pourraient
exprimer le pouvoir de l’utilisateur d’utiliser l’équipement.
EXPOSITION AUX RADIOFRÉQUENCES
Pour se conformer aux exigences d’exposition FCC/IC RF pour les
appareils de transmission mobiles, cet émetteur ne doit être utilisé
ou installé qu’aux endroits où il y a une distance de séparation d’au
moins 20 cm entre l’antenne et toutes les personnes.
En vertu de la réglementation d’Industrie Canada, cet émetteur
radio ne peut fonctionner qu’à l’aide d’une antenne d’un type et
d’un gain maximal (ou inférieur) approuvés pour l’émetteur par
Industrie Canada. Pour réduire les interférences radio potentielles
pour les autres utilisateurs, le type d’antenne et son gain doivent
être choisis de manière à ce que la puissance isotrope rayonnée
équivalente (e.i.r.p.) ne soit pas supérieure à celle nécessaire pour
une communication réussie.
Cet appareil est conforme aux normes RSS exemptes de licence
d’Industrie Canada. L’exploitation est soumise aux deux conditions
suivantes : 1) cet appareil ne doit pas causer d’interférences,
et 2) cet appareil doit accepter toute interférence, y compris les
interférences susceptibles de provoquer un fonctionnement
indésirable de l’appareil.
6
INSTALLATION MANUAL
6. Install a check valve (required) to prevent back-flow. The
RIDGID® check valve (57028-001) may be positioned
just above the basin to allow easy removal of the pump for
cleaning and service.
7. Install a gate valve or ball valve if required by local, regional
or state code.
8. Connect pump power supply cord to a ground fault circuit
interrupter (GFCI) receptacle.
NOTE: Pump will initially run when plugged in to calibrate
Air Switch.
NOTE: Do not pinch or constrict Air Tube.
9. Fill the basin/pit with water. The pump will activate when
the water level has reached level 4 on the controller.
10. The pump will stop when the water level has reached the
switch-off level.
11. Fill the basin/pit with water again. While the pump is
draining the basin/pit, verify the discharge pipe is carrying
the water to a point at least 3 ft. away from the foundation.
If the discharge line is exposed to freezing temperatures,
the pipe must be positioned in a downward slope away
from the foundation so any remaining water will drain away
and not freeze.
12. Secure the basin cover and gasket to the basin to prevent
debris from falling into the basin, prevent personal injury,
and to contain gases and/or odors.
13. For device activation follow the instructions found on the
next page.
TYPICAL SUMP INSTALLATION
1. This installation must be in accordance with the National
Electric Code and all applicable local codes and
ordinances.
2. Use a basin (purchased separately) or pit that is large enough
to accommodate the pump.
3. Clean the basin/pit of all debris.
4. If using a basin, place the pump directly on the bottom of
the basin. To prevent damage set the pump on a solid, level
surface. Do not place pump directly on clay, earth, gravel or
sand. A brick or block must be installed under the pump to
provide a solid base.
5. Install discharge plumbing according to local, regional and
state codes. Rigid PVC pipe is required. Do not use flex
hosing in a permanent application.
Vertical Submersible Sump 1
2
3
5
8
9
7
6
1. GFCI OUTLET 7. SUMP PUMP
2. CHECK VALVE 8. AIR SWITCH
3. VENT PIPE 9. BASIN
4. GASKET/BASIN LID
5 PIPE INLET
6. DISCHARGE PIPE
10. CONTROLLER
11. POWER CORD
12. AIR TUBE
MINIMUM
BASIN
HEIGHT
22 IN.
11 IN. DIAMETER MIN.
410
ON LEVEL
APPROX. 9 IN.
OFF LEVEL
APPROX. 4 IN.
11
12
INSTALLATION MANUAL
7
LED LIGHT DISPLAY (CHECK YOUR APP FOR SPECIFIC REAL TIME PUMP INFORMATION)
Color Symptom/Possible Cause(s) Suggested Remedies
Green 1. Good 1. Your pump is good, there is nothing needed
Yellow 1. A clogged pump inlet
2. Electrical voltage or
polarity issue detected
3. Water level in your pit is
not dropping
4. Your motor is showing
signs of aging
1. Open your sump pit and inspect the pump.
Make sure the inlet screen is free of debris and
there is nothing blocking the fow of water into
the pump.
2. Contact an electrician and have them check the
voltage and wiring of the outlet.
3. Check your pump to be sure it is properly
connected. Then check your discharge pipe for
obstructions or leaks that allow water back into
the pit.
4. Consider replacing your pump soon to stay
protected.
Red 1. There is a critical issue
with your pump
1. Replace your pump immediately.
DIGITAL CONTROLLER BUTTON
Function Action to Take
Mute Alarm Short press (at least 1 second)
System Test Hold for 5 seconds (pump health LED will flash blue) and release
Reboot Hold for 10 seconds (pump health LED will flash green) and release
Reset WiFi
Connection and
Reboot
Hold for 15 seconds (pump health LED will flash yellow), release and short
press (at least 1 second) again to confirm
Reset to Factory
Settings and
Reboot
Hold for 20 seconds (pump health LED will flash red), release and short press
(at least 1 second) again to confirm
A Button Hold Legend can be found on the back of the controller for your convenience.
NOTE: Make sure your Wi-Fi and Bluetooth is connected.
1. Download the SmartSumpbyRIDGID App from your device’s app store.
2. Open the SmartSumpbyRIDGID App and click “+ Add Device” to begin device activation.
3. Select your RIDGID® device.
4. Verify that the status LED on the device is blinking yellow. Click Next to continue.
5. Allow access to your devices camera and use your camera to scan the QR code located on the front of your device.
NOTE: Camera will automatically scan QR code when brought into view.
6. After the app “Finds” your device, a network list of local connections will be displayed. Select your network and enter your
password credentials. Click Send.
7. Once connected to Wi-Fi, your device will be registered.
8. The app will now ask for your zip code. By collecting your zip code, we can link your local weather data with your pump
data in the future.
INSTALLATION MANUAL
DEVICE ACTIVATION INSTRUCTIONS
8
LED LIGHT DISPLAY (CHECK YOUR APP FOR SPECIFIC REAL TIME PUMP INFORMATION)
Color Symptom/Possible Cause(s) Suggested Remedies
Green 1. Good 1. Your pump is good, there is nothing needed
Yellow 1. A clogged pump inlet
2. Electrical voltage or
polarity issue detected
3. Water level in your pit is
not dropping
4. Your motor is showing
signs of aging
1. Open your sump pit and inspect the pump.
Make sure the inlet screen is free of debris and
there is nothing blocking the fow of water into
the pump.
2. Contact an electrician and have them check the
voltage and wiring of the outlet.
3. Check your pump to be sure it is properly
connected. Then check your discharge pipe for
obstructions or leaks that allow water back into
the pit.
4. Consider replacing your pump soon to stay
protected.
Red 1. There is a critical issue
with your pump
1. Replace your pump immediately.
DIGITAL CONTROLLER BUTTON
Function Action to Take
Mute Alarm Short press (at least 1 second)
System Test Hold for 5 seconds (pump health LED will flash blue) and release
Reboot Hold for 10 seconds (pump health LED will flash green) and release
Reset WiFi
Connection and
Reboot
Hold for 15 seconds (pump health LED will flash yellow), release and short
press (at least 1 second) again to confirm
Reset to Factory
Settings and
Reboot
Hold for 20 seconds (pump health LED will flash red), release and short press
(at least 1 second) again to confirm
A Button Hold Legend can be found on the back of the controller for your convenience.
INSTALLATION MANUAL
9
INSTALLATION MANUAL
TROUBLESHOOTING WARNINGS
ALWAYS DISCONNECT THE PUMP FROM POWER SUPPLY before
installing, servicing or making any adjustments.
TOUJOURS METTRE LA POMPE HORS TENSION avant de procéder à
l’installation, à l’entretien ou à des réglages.
LET PUMP COOL FOR A MINIMUM OF 2 HOURS BEFORE ATTEMPTING TO
SERVICE. Submersible pumps contain oil that become pressurized
and hot under normal operating conditions.
LAISSER REFROIDIR LA POMPE PENDANT AU MOINS 2 HEURES AVANT
D’ESSAYER DE LA RÉPARER. Les pompes submersibles contiennent
de l’huile qui devient pressurisée et chaude dans des conditions
normales de fonctionnement.
1. Submersible pump models have permanently lubricated
bearings and require no additional lubrication.
2. Submersible pumps contain dielectric oil for cooling.
Dielectric oil can be harmful to the environment. Follow
state environmental laws when disposing of pump.
3. The pump motor is equipped with automatic resetting
thermal protector and may restart unexpectedly. Protector
tripping is an indication of motor overloading as a result of
operating the pump at low heads, excessively high or low
voltage, inadequate wiring, incorrect motor conditions, or at
the end of product life.
TROUBLESHOOTING CHART FOR PUMP
Symptoms Possible Cause(s) Suggested Remedies
Pump will not
start or run
1. Water level too low
2. Blown fuse or tripped circuit breaker
3. Low supply voltage
4. Motor
5. Switch
6. Inlet screen clogged
7. Switch obstruction
1. Water must be at the appropriate level to activate switch
2. If blown, determine cause and then either replace with proper
sized fuse or reset breaker
3. Contact an electrician
4. Replace pump
5. Verify air tube is not constricted and is connected to switch and
controller
6. Remove debris
7. Remove obstruction to ensure operation of switch
Pump starts and
stops too often
1. Back-flow of water from discharge
pipe
2. Switch
3. Check valve not functioning properly
or leaking
1. Install check valve
2. Run system test. Also, make sure your Air Tube is not
constricted.
3. Remove and examine check valve for prop er in stal la tion and free
operation. Replace check valve if necessary.
Pump shuts off
and turns on
independently
of switch (trips
thermal overload
protection)
1. Excessive water temperature
2. Switch
3. Switch obstruction
4. Obstruction in discharge pipe
5. Low supply voltage
1. Pump should not be used for water above 77º F
2. Run system test. Also, make sure your Air Tube is not
constricted.
3. Remove obstruction to ensure operation of switch
4. Remove obstruction in discharge piping
5. Contact an electrician
INSTALLATION MANUAL
10
TROUBLESHOOTING CHART (CONTINUED)
Symptoms Possible Cause(s) Suggested Remedies
Pump trips GFCI 1. Bad GFCI
2. Bad pump
1. Contact an electrician to replace GFCI
2. Replace pump
Pump operates
noisily or vibrates
excessively
1. Worn bearings
2. Impeller broken
3. Piping attachments to building
structure too rigid or too loose
1. Replace pump
2. Replace pump
3. Install rubber coupling (available at local hardware stores) to
isolate pump vibration from discharge plumbing
Pump will not
shut off
1. Switch
2. Switch obstructions
3. Restricted discharge (obstruction in
piping)
4. Excessive inflow or pump not
properly sized for application
1. Run system test. Also, make sure your Air Tube is not
constricted.
2. Remove obstruction to ensure operation of switch
3. Remove obstruction from discharge piping
4. Recheck all sizing calculations to determine proper pump size
Pump operates
but delivers little
or no water
1. Low supply voltage
2. Inlet screen clogged
3. Broken impeller
4. Pump not properly sized for
application
5. Check valve stuck closed or
installed backwards
6. Shut off valve closed
1. Contact an electrician
2. Remove debris
3. Replace pump
4. Recheck all sizing calculations to determine proper pump size
5. Remove and examine check valve for proper installation and free
operation
6. Open valve
ROUTINE SUMP MAINTENANCE
The pump should be inspected 3-4 times per year for pump movement or buildup of debris on the switch. Reposition pump if it
has moved. Remove any debris that could interfere with the operation of the switch. Lack of proper routine maintenance will void
warranty.
• Make sure the pump is plugged in to a working ground fault circuit interrupter (GFCI) outlet and the cord is in good shape.
In damp areas, GFCI breakers may trip, effectively shutting off the sump pump. Check in on your sump pump and reset the
GFCI if necessary.
• Ensure the pump is standing upright. Vibrations during operation can cause it to fall or tilt onto one side.
• Pour a bucket of water into the pit to make sure the pump starts automatically and the water drains quickly once the pump
is on. If the pump doesn’t start, have it serviced or replaced.
• Check the inlet screen and clear away any small stones or debris.
11
INSTALLATION MANUAL INSTALLATION MANUAL
MUTE ALARM:
Will silence alarm for 12 hours. For custom mutes times, open the companion app while the alarm is active and press
the alarm icon next to the alert pop-up.
SYSTEM TEST:
While your pump will automatically run periodic system tests; you can always force a system test via the controller or the
companion app. A complete System Test which analyzes all aspects of Pump Health will be performed at Water Level
2 or higher. A partial System Test may be initiated at Water Level 1 or lower but will not be able to analyze all aspects of
Pump Health.
REBOOT:
Will perform a Reboot of your device.
RESET WI-FI CONNECTION AND REBOOT:
Use this function to re-establish an existing or new connection to your device without losing any personalized settings or
data associated with your device.
NOTE: It is highly recommended that a Wi-Fi connection reset follow the direction on the app for resetting the Wi-Fi
connection for your device.
RESET TO FACTORY SETTINGS AND REBOOT:
NOTE: It is highly recommended that a Factory Reset be initiated from the device settings for your pump within the
companion app while the device is connected to Wi-Fi. A Factory Reset can be initiated from the app by navigating
to the setting for your pump and selecting “Deactivate Pump”. Confirming will remove data for this pump from your
account and will prompt the Pump Controller to perform a Factory Reset and Reboot.
USING YOUR DIGITAL CONTROLLER
INSTALLATION MANUAL
12
INSTALLATION MANUAL
FOR REPLACEMENT
PARTS OR CUSTOMER SUPPORT,
CALL 1-877-9RIDGID®
Please provide following information:
- Model number
- Serial number on cord tag (not to be removed)
- Part description and number as shown in parts list
Thank you for making RIDGID® Pumps a key part of your
home maintenance program. If properly installed, maintained and
operated in accordance with RIDGID® Pumps’ written instructions,
your pump should provide you with approximately
( * ) years of service.
Product Warranty ( * ) Expected Life
5 6
LIMITED WARRANTY
For ve years for the 1000RSDSSmart from the date of purchase, from an authorized dealer, RIDGID® Pumps will repair or replace, at its option
for the original purchaser, any part or parts of its Sump Pumps or Water Pumps (“Product”) found upon examination by RIDGID® Pumps to be
defective in materials or workmanship. Please call RIDGID® Pumps (1-877-9RIDGID®) for warranty instructions. Be prepared to provide the model
number and the serial number when exercising this warranty. All transportation charges on Products or parts submitted for repair or replacement
must be paid by purchaser. This Limited Warranty is not transferrable. This Limited Warranty does not cover Products which have been damaged
as a result of accident, abuse, misuse, neglect, improper installation, improper maintenance, or failure to operate in accordance with RIDGID® ’s
written instructions.
This Limited Warranty does not cover Products which have been damaged as a result of accident, abuse, misuse, neglect, improper installation,
improper maintenance, or failure to operate in accordance with RIDGID® Pumps’ written instructions.
THIS WARRANTY IS IN LIEU OF ANY AND ALL OTHER WARRANTIES, OBLIGATIONS OR AGREEMENTS, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE, AND ANY RIGHTS OR REMEDIES AGAINST ANY PERSON OR ENTITY UNDER THE
UNIFORM COMMERCIAL CODE OR OTHERWISE WITH RESPECT TO THE SALE OF THE PRODUCT. THE REMEDIES AND OBLIGATIONS STATED IN THIS WARRANTY ARE
THE SOLE AND EXCLUSIVE REMEDIES OF AND OBLIGATIONS TO THE OWNER FOR ANY AND ALL MATTERS ARISING WITH RESPECT TO OR IN ANY WAY CONNECTED
WITH THE PRODUCT, REGARDLESS OF THE SOURCE OR PROVIDER OF SUCH GOODS. IN NO EVENT, WHETHER AS A RESULT OF BREACH OF CONTRACT, WARRANTY
TORT (INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL RIDGID® PUMPS OR ANY AFFILIATE BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES.
You MUST retain your purchase receipt along with this form. In the event you need to exercise a warranty claim, you MUST send a copy of the
purchase receipt along with the material or correspondence. Please call RIDGID® Pumps (1-877-9RIDGID®) for return authorization and
instructions.
DO NOT MAIL THIS FORM TO RIDGID® Pumps. Use this form only to maintain your records.
MODEL NO._____________________ SERIAL NO._________________________ INSTALLATION DATE __________________________
ADDRESS PARTS CORRESPONDENCE TO:
RIDGID® Pumps
101 Production Drive
Harrison, OH 45030 U.S.A.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
RIDGID 1000RSDS Manuel utilisateur
- Catégorie
- Pistolets à chaleur
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
- English: RIDGID 1000RSDS User manual