LG LMWC23626S Le manuel du propriétaire

OWNER'S MANUAL

FRENCH DOOR

REFRIGERATOR

Read this owner's manual thoroughly before operating the

appliance and keep it handy for reference at all times.

ENGLISH / ESPAÑOL / FRANÇAIS

LMWS27626* / LMWC23626*

MFL70761724

Rev.02_020620

www.lg.com

TABLE OF CONTENTS

2

3 SAFETY INSTRUCTIONS

3 READ ALL INSTRUCTIONS BEFORE USE

3 WARNING

6 CAUTION

7 PRODUCT OVERVIEW

7 Product Features

10 INSTALLATION

10 Before Installing

11 Choosing the Proper Location

13 Removing/Assembling the Handles

14 Removing/Assembling the Doors and Drawer

18 Connecting the Water Line

21 Leveling and Door Alignment

21 Turning on the Power

22 OPERATION

22 Before Use

23 Control Panel

24 Sabbath Mode

24 Water Dispenser

24 Automatic Icemaker

25 Storing Food

27 Humidity Controlled Crispers

28 Glide‘N’Serve

28 Refrigerator Shelves

29 Door Bins

29 Durabase

30 SMART FUNCTIONS

30 LG ThinQ Application

30 Smart Diagnosis™ Feature

31 MAINTENANCE

31 Cleaning

32 Water Filter

35 TROUBLESHOOTING

35 FAQs

36 Before Calling for Service

45 LIMITED WARRANTY

45 For USA

49 For Canada

3SAFETY INSTRUCTIONS

ENGLISH

SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

Safety Messages

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and

follow all safety messages.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury,

and tell you what may happen if the instructions are not followed.

WARNING

• To reduce the risk of explosion, fire, death, electric shock, scalding or injury to persons when using this

product, follow basic precautions, including the following:

Installation

• To reduce the risk of injury to persons, adhere to all industry recommended safety procedures including

the use of long-sleeved gloves and safety glasses.

• Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has

missing or broken parts, including a damaged cord or plug.

• Only connect this product to a dedicated grounded electrical outlet rated for use with this product (115

V, 60 Hz, AC only). It is the user’s responsibility to replace a standard 2-prong wall outlet with a standard

3-prong wall outlet.

• Do not use an outlet that can be turned off with a switch. Do not use an extension cord.

• The appliance must be positioned for easy access to a power source.

• When moving the refrigerator, be careful not to roll over or damage the power cord.

• Contact an authorized service center when installing or relocating the refrigerator.

• Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

• Keep packing materials out of the reach of children. Packaging material can be dangerous for children.

There is a risk of suffocation.

• Do not install the refrigerator in a damp or dusty place where insulation on electrical parts may

deteriorate.

• Do not place the refrigerator in direct sunlight or expose it to the heat from heating appliances such as

stoves or heaters.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or injure you and others. All safety messages

will follow the safety alert symbol and either the word WARNING or CAUTION.

These words mean:

WARNING

You may be killed or seriously injured if you do not follow instructions.

CAUTION

You may be injured or cause damage to the product if you do not follow instructions.

4 SAFETY INSTRUCTIONS

• Do not bend or pinch the power cord excessively or place heavy objects on it.

Operation

• This appliance is intended to be used in household and similar applications such as :

- staff kitchen areas in shops, offices and other working environments;

- farm houses and by clients in hotels, motels and other residential type environments;

- bed and breakfast type environments;

- catering and similar non-retail applications.

• This product is not to be used for special purposes such as the storage of medicine or test materials or

for use on ships, etc.

• DO NOT allow children to climb, stand, or hang on the refrigerator doors or on the shelves in the

refrigerator. They could damage the refrigerator and seriously injure themselves.

• Do not allow children to climb into the refrigerator. They could be trapped and suffocated.

• Children should be supervised to ensure that they do not play with the refrigerator.

• Keep fingers out of pinch point areas; clearances between the doors and cabinets are necessarily small.

Be careful closing doors when children are nearby.

• Do not touch frozen food or the metal parts in the freezer compartment with wet or damp hands. Doing

so may cause frostbite.

• Do not refreeze frozen food that has thawed completely. Doing so may result in a serious health hazard.

• Do not use an adapter plug or plug the power plug into a multi-outlet extension cord.

• If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly

qualified person in order to avoid a hazard.

• Do not operate the refrigerator or touch the power cord with wet hands.

• Do not modify or extend the power cord.

• Do not use an uncertified power outlet. Do not plug appliance into a damaged wall outlet.

• Do not put hands, feet or other objects into the air vents or bottom of the refrigerator. Doing so could

result in personal injury or electric shock.

• In the event of a gas leak (propane/LPG), ensure the area is adequately ventilated and contact an

authorized service center before resuming use. Do not touch the refrigerator or power cord of the

refrigerator.

• Disconnect the power cord immediately and contact an authorized service center if there is a strange

noise, odor, or smoke coming from the appliance.

• Do not use any fuse (such as copper, steel wire, etc.) other than a standard fuse.

• Do not place or use an electrical appliance inside the refrigerator, unless it is of a type recommended by

the manufacturer.

• Do not put animals inside the appliance.

• Do not place heavy or fragile objects, liquid filled containers, combustible substances, or flammable

objects (such as candles and lamps) on the appliance.

• Avoid contact with any moving parts of the ejector mechanism or with the heater that releases the ice

cubes.

• If connected to a circuit protected by fuses, use time delay fuse.

• Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction.

• Do not use mechanical devices or other means to accelerate the defrosting process, other than those

recommended by the manufacturer.

• Do not use electrical appliances inside the food storage compartments of the appliance, unless they are

of the type recommended by the manufacturer.

• Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.

5SAFETY INSTRUCTIONS

ENGLISH

• DO NOT place fingers in the automatic icemaker when the refrigerator is plugged in.

• When dispensing ice from the dispenser, do not use a fragile container.

Maintenance

• Do not use a hair dryer to dry the inside of the refrigerator.

• Do not light a candle to remove odors in the refrigerator.

• In the event of a refrigerant leak, move flammable objects away from the refrigerator. Ensure the area is

adequately ventilated and contact an authorized service center.

• Keep flammable materials and vapors, such as gasoline, away from the refrigerator.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person responsible for their safety.

• Unplug the power plug before cleaning or repairing the refrigerator.

• The refrigerator and freezer compartment lights are interior LED lighting, and service should be

performed by a qualified technician.

• Unplug the power plug immediately in the event of a blackout or thunderstorm.

• Turn the power off if water or dust penetrates into the refrigerator. Call a service agent.

• Do not store glass containers or soda in the freezer compartment. Contents may expand when frozen,

break the container and cause injury.

• Do not store, disassemble or repair the appliance yourself or allow unqualified personnel to do so.

Disposal

• Junked or abandoned refrigerators are dangerous, even if they are sitting for only a few days. When

disposing of the refrigerator, remove the packing materials from the door or take off the doors but leave

the shelves in place so that children may not easily climb inside.

• If disposing of a refrigerator, make sure the refrigerant and insulation foam are removed for proper

disposal by a qualified servicer. If you release the refrigerant or throw away the insulation foam, you

may be fined or imprisoned in accordance with the relevant environmental law. Insulation foam contains

flammable blowing gas.

• When discarding the appliance, remove the door gasket while leaving the shelves and baskets in place,

and keep children away from the appliance.

Grounding Instructions

• Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check

with a qualified electrician or service personnel if you are in doubt whether the appliance is properly

grounded. Do not modify the plug provided with the appliance; if it will not fit the outlet, have a proper

outlet installed by a qualified electrician.

• Have a certified electrician check the wall outlet and wiring for proper grounding.

• Never unplug the appliance by pulling on the power cord. Always grip the plug firmly and pull straight

out from the outlet. Failure to do so may damage the power cord, resulting in a risk of fire and electric

shock.

6 SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

Risk of Fire and Flammable Materials

CAUTION

• To reduce the risk of minor or moderate injury to persons, malfunction, or damage to the product or

property when using this product, follow basic precautions, including the following:

Installation

• Do not install the refrigerator where there may be a danger of the unit falling.

• The refrigerator must be properly installed in accordance with the Installation Instructions.

Operation

• Do not use aerosols near the refrigerator.

• This appliance is intended to be used only in domestic and similar applications.

• Do not strike or apply excessive force to any glass surface. Do not touch glass surfaces if they are

cracked or broken.

• Do not overfill or pack items too tightly into door bins. Doing so may cause damage to the bin or

personal injury if items are removed with excessive force.

• Do not hang on to or place heavy objects on the refrigerator’s dispenser.

Maintenance

• Do not use strong detergents like wax or thinners for cleaning. Clean with a soft cloth.

• Remove foreign objects (such as dust and water) off the prongs of the power plug and contact areas. Do

not use a wet or damp cloth when cleaning the plug.

• Do not spray water directly on the inside or outside of the refrigerator.

• Do not clean glass shelves or covers with warm water when they are cold. They may break if exposed to

sudden temperature changes.

This appliance contains a small amount of isobutane refrigerant (R600a), which is combustible.

When transporting and installing the appliance, care should be taken to ensure that no parts

of the refrigerating circuit are damaged. Refrigerant squirting out of the pipes could ignite or

cause an eye injury. If a leak is detected, avoid any naked flames or potential sources of

ignition and air the room in which the appliance is standing for several minutes.

In order to avoid the creation of a flammable gas air mixture if a leak in the refrigerating

circuit occurs, the size of the room in which the appliance may be sited depends on the

amount of refrigerant used. The room must be 10.8 square feet (1 square meter) in size for

every 8g of R600a refrigerant inside the appliance. The amount of refrigerant in your

particular appliance is shown on the identification plate inside the appliance. Never start up an

appliance showing any signs of damage. If in doubt, consult your dealer.

7PRODUCT OVERVIEW

ENGLISH

PRODUCT OVERVIEW

Product Features

The images in this guide may be different from the actual components and accessories, which are subject

to change by the manufacturer without prior notice for product improvement purposes.

Exterior

a Refrigerator

Fresh food compartment

b Freezer Handle

Opens the freezer drawer.

c Refrigerator Handle

Opens and closes the refrigerator door.

d LED Light

Lights up when the freezer door is opened.

e Freezer

Frozen food compartment

8 PRODUCT OVERVIEW

Interior

LMWS27626*

a LED Interior Lighting

Lights up the inside of the refrigerator.

b Water Filter

Purifies water.

c Water Dispenser

Dispenses purified water.

d Door Mullion

Prevents the cold air in the refrigerator from escaping when the doors are closed.

CAUTION

• To reduce the risk of scratching the door or breaking the center door mullion, make sure that the folding

door mullion is folded in before closing the left-hand door.

• The door alarm will sound every 30 seconds if the door remains open longer than one minute.

e Humidity Controlled Crisper

Helps vegetables and fruit to stay crisp and controls humidity.

f Fixed Door Bin

Stores chilled food or drinks.

g Auto-Closing Hinge

The refrigerator doors and freezer drawers close automatically when pushed slightly. (The door only

closes automatically when it is open at an angle of less than 30°.)

h Automatic Icemaker (Freezer)

Dispenses ice automatically.

9PRODUCT OVERVIEW

ENGLISH

i Control Panel

Sets the refrigerator and freezer temperatures.

j Modular Door Bin

Interchangeable bins can be arranged to suit storage needs.

k Adjustable Refrigerator Shelf

The refrigerator shelves are adjustable to meet individual storage needs.

l Glide'N'Serve

Stores food items at a different temperature than the regular refrigerator area.

m Ice Bin

Stores ice from the freezer icemaker.

n Durabase and Durabase Divider

Provides storage for large frozen food items.

Product Specifications

The appearance and specifications listed in this manual may vary due to constant product improvements.

Electrical requirements: 115 V, 60 Hz

Min. / Max. water pressure: 20 - 120 psi (138 - 827 kPa)

Model LMWS27626*

Description Standard-depth, French door refrigerator, bottom freezer

Net weight 287 lb (130 kg)

Model LMWC23626*

Description Standard-depth, French door refrigerator, bottom freezer

Net weight 265 lb (120 kg)

10 INSTALLATION

INSTALLATION

Before Installing

Installation Overview

Please read the following installation instructions first after purchasing this product or transporting it to

another location.

a Unpacking the Refrigerator

b Choosing the Proper Location

c Disassembling/Assembling

d Connecting the Water Line

e Leveling and Door Alignment

WARNING

• Connect to potable water supply only.

11INSTALLATION

ENGLISH

Unpacking the Refrigerator

WARNING

• Use two or more people to move and install the

refrigerator. Failure to do so can result in back

injury or other injury.

• The refrigerator is heavy. Protect the floor when

moving the refrigerator for cleaning or service.

Always pull the refrigerator straight out when

moving it. Do not wiggle or walk the refrigerator

when trying to move it, as floor damage could

occur.

• Keep flammable materials and vapors, such as

gasoline, away from the refrigerator. Failure to

do so can result in fire, explosion, or death.

NOTE

• Remove tape and any temporary labels from

your refrigerator before using. Do not remove

any warning labels, the model and serial number

label, or the Tech Sheet that is located under the

front of the refrigerator.

• To remove any remaining tape or glue, rub the

area briskly with your thumb. Tape or glue

residue can also be easily removed by rubbing a

small amount of liquid dish soap over the

adhesive with your fingers. Wipe with warm

water and dry.

• Do not use sharp instruments, rubbing alcohol,

flammable fluids, or abrasive cleaners to remove

tape or glue. These products can damage the

surface of your refrigerator.

• Reinstall or adjust shelves as needed.

Refrigerator shelves are installed in the shipping

position. Reinstall shelves according to your

individual storage needs.

Choosing the Proper

Location

Water

Must be located where a water supply can be

connected for the automatic icemaker.

NOTE

• The water pressure must be 20 - 120 psi or 138 -

827 kPa or 1.4 - 8.4 kgf/cm

2

. If the refrigerator is

installed in an area with low water pressure

(below 20 psi or 138 kPa or 1.4 kgf/cm

2

), you can

install a booster pump to compensate for the

low pressure.

Electricity

Use an individual, grounded outlet:115 Volts, 60

Hz, AC, 15 Amps minimum.

WARNING

• Do not overload house wiring and cause a fire

hazard by plugging in multiple appliances in the

same outlet with the refrigerator.

• To reduce the risk of electric shock, do not install

the refrigerator in a wet or damp area.

Flooring

To avoid noise and vibration, the unit must be

installed and leveled on a solidly constructed floor.

If required, adjust the leveling legs to compensate

for the unevenness of the floor.

NOTE

• Installing on carpeting, soft tile surfaces, a

platform or weakly supported structure is not

recommended.

Ambient Temperature

Install this appliance in an area where the

temperature is between 55 °F (13 °C) and 110 °F

(43 °C).

If the temperature around the appliance is too low

or high, cooling ability may be adversely affected.

12 INSTALLATION

Dimensions and Clearances

• Check the dimensions of the appliance and the installation path to ensure there is sufficient room to

move the refrigerator through doors or narrow openings.

• If an opening is too narrow to fit the refrigerator through, remove the refrigerator doors. See Removing/

Assembling the Doors and Drawers in this manual.

• The installation location chosen for the refrigerator should allow space behind the unit for connections

and airflow and space in front to open the doors and drawers.

• Too small of a distance from adjacent items may result in lowered freezing capability and increased

electricity consumption charges. Allow at least 24 inches (610 mm) in front of the refrigerator to open the

doors, and at least 2 inches (50.8 mm) between the back of the refrigerator and the wall.

- Dimension/Clearance LMWS27626* LMWC23626*

A Depth without Handle 32 3/8˝ (822 mm) 28 5/8˝ (728 mm)

B Width 35 3/4" (908 mm) 35 3/4" (908 mm)

C Height to Top of Case 68 3/8" (1737 mm) 68 3/8" (1737 mm)

D Height to Top of Hinge 69 3/4" (1772 mm) 69 3/4" (1772 mm)

E Back Clearance 2" (50 mm) 2" (50 mm)

F Depth without Door 28 1/2˝ (724 mm)

24 3/4˝ (630 mm)

G Depth with Handle 30 7/8˝ (886 mm) 31 1/4˝ (792 mm)

H Depth (Total with Freezer Drawer Open) 54 3/4˝ (1391 mm) 51˝ (1297 mm)

I Depth (Total with Door Open 90°) 47 1/8˝ (1197 mm) 43 3/8˝ (1103 mm)

B

A

C

D

F

I

H

E

G

13INSTALLATION

ENGLISH

Removing/Assembling the

Handles

When moving the refrigerator through a narrow

opening, removing the doors is preferred.

The appearance of the handles may vary from

what is shown.

WARNING

• When assembling or disassembling the

refrigerator handles, grasp the handle firmly to

avoid dropping it.

• Do not swing the handle into nearby people or

animals.

• Make sure that the bracket hole of the handle

fits properly into the stopper bolt of the door.

Assemble the set screws to fix the handle into

place.

• Make sure that there is not a gap between the

door and handle after assembling the handle.

Tools Needed

• 3/32 in. Allen wrench

• 1/8 in. Allen wrench

• 1/4 in. Allen wrench

Removing the Refrigerator Handles

1 Loosen the set screws a with a 3/32 in. Allen

wrench and remove the handle.

2 Loosen the mounting fasteners b that

connect to the refrigerator door and handle

using a ¼ in. Allen wrench, and remove the

mounting fasteners.

Assembling the Refrigerator

Handles

1 Assemble the mounting fasteners a at both

ends of the handle with a 1/4 in. Allen wrench.

2 Place the handle on the door by fitting the

handle footprints over the mounting

fasteners and tightening the set screws

b

with a 3/32 in. Allen wrench.

Removing the Freezer Drawer

Handle

1 Loosen the set screws a located on the lower

side of the handle with a 1/8 in. Allen wrench

and remove the handle.

2 Loosen the mounting fasteners b with a 1/4

in. Allen wrench, and remove the mounting

fasteners.

Assembling the Freezer Drawer

Handle

1 Assemble the mounting fasteners a at both

ends of the handle with a 1/4 in. Allen wrench.

2 Place the handle on the door by fitting the

handle footprints over the mounting

fasteners and tightening the set screws

b

with a 1/8 in. Allen wrench.

14 INSTALLATION

Removing/Assembling the

Doors and Drawer

If the entrance door is too narrow for the

refrigerator to pass through, remove the

refrigerator doors and move the refrigerator

sideways through the doorway.

WARNING

• Use two or more people to remove and install

the refrigerator doors and freezer drawer.

• Disconnect the electrical supply to the

refrigerator before installing.

• Do not put hands, feet or other objects into the

air vents or bottom of the refrigerator.

• Be careful when handling the hinge and stopper.

WARNING

• Remove food and bins before detaching the

doors and drawer.

• Do not hold the handle when removing or

replacing the doors and drawer as the handle

may come off.

Tools Needed

3/32 in. Allen wrench

1/8 in. Allen wrench

1/4 in. Allen wrench

Removing the Left Refrigerator

Door

1 Remove the screw a from the hinge cover at

the top of the refrigerator. Lift the hook (not

visible), located at the bottom of the front side

of the cover

b with a flat-head screwdriver.

Remove the cover

2 Disconnect all wire harnesses c. Unscrew the

ground wire

d .

3 Rotate the hinge lever e counterclockwise.

Lift the top hinge

f free of the hinge lever

latch

g .

CAUTION

• When lifting the hinge free of the latch, be

careful that the door does not fall forward.

4 Lift the door from the middle hinge pin and

remove the door.

CAUTION

• Place the door, inside facing up, on a

nonscratching surface.

Removing the Right Refrigerator

Door

1 Remove the top hinge cover screw a. Lift the

hook (not visible), located at the bottom of the

front side of the cover

b, with a flat-head

screwdriver.

15INSTALLATION

ENGLISH

2 Detach all the wire harnesses c.

3 Rotate the hinge lever d clockwise. Lift the

top hinge

e free of the hinge lever latch f.

CAUTION

• When lifting the hinge free of the latch, be

careful that the door does not fall forward.

4 Lift the door from the middle hinge pin and

remove the door.

CAUTION

• Place the door, inside facing up, on a

nonscratching surface.

Assembling the Right Refrigerator

Door

CAUTION

• Install the right-side door first.

1 Make sure that the plastic sleeve is inserted in

the bottom of the door. Lower the door onto

the middle hinge pin as shown in the figure.

2 Fit the hinge a over the hinge lever latch b

and slot it into place. Rotate the lever

c

counterclockwise to secure the hinge.

3 Connect the wire harnesses d.

4 Place the cover e in its place. Insert and

tighten the cover screw

f .

16 INSTALLATION

Assembling the Left Refrigerator

Door

CAUTION

• Install the left refrigerator door after the right

door is installed.

1 Make sure that the plastic sleeve is inserted in

the bottom of the door. Install the refrigerator

door onto the middle hinge.

2 Fit the hinge a over the hinge lever latch b

and slot it into place. Rotate the lever

c

clockwise and fasten the hinge.

3 Connect all the wire harnesses d and the

ground screw

e.

4 Place the hinge cover f in place. Insert and

tighten the cover screw

g.

Removing the Freezer Drawer

Removing the lower freezer drawer in the same

way.

WARNING

• Use two or more people to remove and install

the refrigerator doors and freezer drawer.

• Be careful of sharp hinges on both sides of the

drawer.

• When you lay the drawer down, be careful not to

damage the floor.

• Do not sit or stand on the freezer drawer.

• To prevent accidents, keep children and pets

away from the drawer. Do not leave the drawer

open. If the Durabase

®

storage bin is removed

from the freezer drawer, there is sufficient space

for a small child or pet to crawl inside.

1 Pull the drawer open to full extension.

Removing the basket and ice bin from the

rails.

2 Remove the screws from the rails at both

ends.

3 Grip both sides of the drawer and pull it up to

remove it from the rails.

17INSTALLATION

ENGLISH

CAUTION

• Do not hold the handle when removing or

replacing the drawer. The handle may come off,

causing personal injury.

4 Hold both rails and push them in

simultaneously.

Assembling the Freezer Drawer

Assembling the lower freezer drawer in the same

way.

1 Pull out both rails simultaneously, until they

are fully extended.

2 Grasp the drawer on each side and hook the

drawer supports into the rail tabs located on

both sides.

CAUTION

• Do not hold the handle when removing or

replacing the drawer. The handle may come off,

causing personal injury.

3 Lower the door into its final position and

insert the screws in the rails on both sides.

4 Insert the basket into the frame, and push the

drawer back until it clicks into place.

18 INSTALLATION

Connecting the Water Line

Before Beginning

This water line installation is not covered by the

refrigerator warranty. Follow these instructions

carefully to minimize the risk of expensive water

damage.

If necessary, call a qualified plumber to correct

water hammer before installing the water supply

line to the refrigerator. Water banging in the

pipes, or water hammer in residential plumbing

can cause damage to refrigerator parts and lead to

water leakage or flooding.

• Turn the icemaker OFF if the refrigerator will be

used before the water line is connected.

• Do not install the icemaker tubing in areas

where the ambient temperatures fall below

freezing.

WARNING

• Connect to potable water supply only.

CAUTION

• To prevent burns and product damage, only

connect the refrigerator water line to a cold

water supply.

• Wear eye protection during installation to

prevent injury.

Water Pressure

You will need a cold water supply.

If the water pressure from the reverse osmosis

system is less than 20 psi or 138 kPa or 1.4 kgf/

cm

2

(takes more than 4 seconds to fill a cup of 7 oz

or 198 cc capacity):

• Check to see if the sediment filter in the reverse

osmosis system is blocked. Replace the filter if

necessary.

• Allow the storage tank on the reverse osmosis

system to refill after heavy usage.

• If the water pressure remains low, call a

licensed, qualified plumber.

• All installations must be in accordance with local

plumbing code requirements.

Supplies Needed

• Copper or PEX Tubing, ¼ in. outer diameter, to

connect the refrigerator to the water supply. Be

sure both ends of the tubing are cut square. To

determine how much tubing you need, measure

the distance from the water valve on the back of

the refrigerator to the water supply pipe. Then,

add 8 feet (2.4 m). Be sure there is sufficient

extra tubing (about 8 feet [2.4 m] coiled into 3

turns of about 10 in. [25 cm] diameter) to allow

the refrigerator to move out from the wall after

installation.

• Power drill.

• ½ in. or adjustable wrench.

• Flat-blade and Phillips-head screwdrivers.

• Two ¼ in. outer diameter compression nuts

and 2 ferrules (sleeves) to connect the copper

tubing to the shutoff valve and the refrigerator

water valve.

• If your existing copper water line has a flared

fitting at the end, purchase an adapter (available

at plumbing supply stores) to connect the water

line to the refrigerator OR cut off the flared

fitting with a tube cutter and then use a

compression fitting.

• Shutoff valve to connect to the cold water line.

The shutoff valve should have a water inlet with

a minimum inside diameter of 5/32 in. at the

point of connection to the COLD WATER LINE.

Saddle-type shutoff valves are included in many

water supply kits. Before purchasing, make sure

a saddle-type valve complies with your local

plumbing codes.

Water Pressure

models with water

filter

20 - 120 psi (138 - 827 kPa)

where reverse

osmosis water

filtration system is

connected to a cold

water supply

40 - 60 psi minimum to

reverse osmosis system

(2.8 kgf/cm

2

- 4.2 kgf/ cm

2

,

or less than 2 - 3 seconds to

fill a cup of 7 oz capacity)

19INSTALLATION

ENGLISH

NOTE

• A self-piercing saddle type water valve should

not be used.

Water Line Installation Instructions

Install the shutoff valve on the nearest frequently

used drinking water line.

WARNING

• When using any electrical device (such as a

power drill) during installation, be sure the

device is battery-powered, double-insulated or

grounded in a manner that will prevent the

hazard of electric shock.

1 Shut off the main water supply.

• Turn on the nearest faucet to relieve the

pressure on the line.

2 Choose the valve location.

• Choose a location for the valve that is easily

accessible. It is best to connect into the side

of a vertical water pipe. When it is necessary

to connect into a horizontal water pipe,

make the connection to the top or side,

rather than at the bottom, to avoid drawing

off any sediment from the water pipe.

3 Drill the hole for the valve.

• Drill a ¼ in. hole in the water pipe using a

sharp bit. Remove any burrs resulting from

drilling the hole in the pipe. Be careful not

to allow water to drain into the drill. Failure

to drill a ¼ in. hole may result in reduced ice

production or smaller cubes.

NOTE

• The hookup line cannot be white, plastic tubing.

Licensed plumbers must use only copper tubing

(NDA tubing #49595 or #49599) or Cross Link

Polyethylene (PEX) tubing.

4 Fasten the shutoff valve.

• Fasten the shutoff valve to the cold water

pipe with the pipe clamp.

NOTE

• Commonwealth of Massachusetts Plumbing

Codes 248CMR shall be adhered to. Saddle

valves are illegal and use is not permitted in

Massachusetts. Consult with your licensed

plumber.

a Pipe Clamp

b Saddle-Type Shutoff Valve

c Vertical Cold Water Pipe

5 Tighten the pipe clamp.

• Tighten the clamp screws until the sealing

washer begins to swell.

NOTE

• Do not over tighten clamp or you may crush the

tubing.

20 INSTALLATION

a Pipe Clamp

b Inlet End

c Clamp Screw

d Washer

6 Route the tubing.

• Route the tubing between the cold water

line and the refrigerator. Route the tubing

through a hole drilled in the wall or floor

(behind the refrigerator or adjacent base

cabinet) as close to the wall as possible.

NOTE

• Be sure there is sufficient extra tubing (about 8

ft. coiled into three turns of about 10 in.

diameter) to allow the refrigerator to move out

from the wall after installation.

7 Connect the tubing to the valve.

• Place the compression nut and ferrule

(sleeve) for copper tubing onto the end of

the tubing and connect it to the shutoff

valve. Make sure the tubing is fully inserted

into the valve. Tighten the compression nut

securely.

a Saddle-Type Shutoff Valve

b Compression Nut

c Packing Nut

d Outlet Valve

e Ferrule (sleeve)

8 Flush out the tubing.

• Turn the main water supply on and flush

out the tubing until the water is clear. Shut

the water off at the water valve after about

one quart of water has been flushed

through the tubing.

9 Connect the tubing to the refrigerator.

NOTE

• Before making the connection to the

refrigerator, be sure that the refrigerator power

cord is not plugged into the wall outlet.

• Remove the plastic flexible cap from the water

valve.

• Place the compression nut and ferrule (sleeve)

onto the end of the tubing as shown.

• Insert the end of the copper tubing into the

connection as far as possible. While holding the

tubing, tighten the fitting.

a Tubing Clamp

b ¼ in. Tubing

c ¼ in. Compression Nut

d Ferrule (sleeve)

e Refrigerator Connection

La page est en cours de chargement...

LG LMWC23626S Le manuel du propriétaire

LG LMWC23626S Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents