Simplicity 020532-01 Manuel utilisateur

Catégorie
Nettoyeurs haute pression
Taper
Manuel utilisateur
2700 PSI* @ 2.1 GPM MAX
2100 PSI @ 2.3 GPM MAX*
PRESSURE WASHER
Operator’s Manual
Model No. C950.672161
Part No. 80013367 Rev A (03/07/2016)
• Safety
Assembly
Operation
Maintenance
• Parts
Français, p. 34
HOURS: Mon. - Fri. 8 a.m. to 5 p.m. (CT)
PRESSURE WASHER
CUSTOMER HELPLINE
1-800-222-3136
WARNING
Before using this product, read this
manual and follow all Safety Rules
and Operating Instructions.
Sears Canada, Inc.
Visit our Craftsman website: www.sears.ca
AVERTISSEMENT
Avant d’utiliser ce produit, veuillez lire
le manuel et suivre toutes les directives
relatives à la sécurité et à l’utilisation.
* This pressure washer is rated in accordance to the Pressure Washer Manufacturers Association (PWMA) standard PW101-
2010 (Testing and Rating Performance of Pressure Washers).
* Les caractéristiques nominales de ce nettoyeur à haute pression sont conformes à la norme PW101-2010 de la Pressure
Washer Manufacturers Association (PWMA) (Tests et performance nominale des nettoyeurs à haute pression).
WARRANTY
2
TABLE OF CONTENTS
CRAFTSMAN LIMITED WARRANTY
General:
time period as set-out below (the “Warranty Period”). Warranties extend to the original purchaser of a Craftsman
product only. Purchases made through an online auction or through any website other than www.sears.ca are
excluded. The relevant Warranty Period commences on the original date of purchase. Within this period, Sears
Canada, Inc. will, at its sole option, repair or replace any products or components which fail in normal use. Such
repairs or replacement will be made at no charge to the customer for parts or labor, provided that the customer
shall be responsible for any transportation cost.
Exclusions: This warranty does not cover failures due to normal wear, abuse, misuse, neglect (including but not
limited to the use of stale fuel, dirt, abrasives, moisture, rust, corrosion, or any adverse reaction due to improper
storage or use habits), improper maintenance or failure to follow maintenance guidelines and/or instructions,
failure to operate the product in accordance with the owner’s manual or any additional instructions or information
provided at the time of purchase or in subsequent communications with the original purchaser, accident or
unauthorized alterations or repairs made or attempted by others. Also excluded from warranty coverage – except
as provided below - are the following: maintenance, adjustments, components subject to wear including but not

grips, recoil assembly’s, saw chains and bars, trimmer lines and spools, spark plugs, starter ropers and tines, and


Repairs: Repairs conducted within the Warranty Period will be warranted until the end of the original Warranty
Period.
Disclaimers: THE WARRANTIES AND REMEDIES CONTAINED HEREIN ARE EXCLUSIVE AND IN LIEU OF
ALL OTHER WARRANTIES, WHETHER ORAL OR WRITTEN (OTHER THAN AS STATED HEREIN), AND
WHETHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING BUT NOT LIMITED TO ANY. THIS WARRANTY
GIVES YOU SPECIFIC LEGAL RIGHTS, WHICH MAY VARY FROM PROVINCE TO PROVINCE.
IN NO EVENT SHALL SEARS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT OR CONSEQUENTIAL
DAMAGES, WHETHER RESULTING FROM THE USE, MISUSE OR INABILITY TO USE THE PRODUCT OR
FROM DEFECTS IN THE PRODUCT. THE EXCLUSIONS IN THIS PARAGRAPH SHALL NOT APPLY IN
JURISDICATIONS WHERE APPLICABLE LAW DOES NOT ALLOW FOR THE EXCLUSION OF INCIDENTAL
OR CONSEQUENTIAL DAMAGES. IN SUCH JURISDICTIONS, THIS PARAGRAPH SHALL NOT APPLY, BUT
THE REMAINING PROVISIONS OF THIS DOCUMENT SHALL REMAIN VALID.

sole discretion. SUCH REMEDY SHALL BE YOUR SOLE AND EXCLUSIVE REMEDY FOR ANY BREACH OF
WARRANTY.
WARRANTY .....................................
SAFETY RULES ..................................
FEATURES AND CONTROLS ........................7
ASSEMBLY.....................................
OPERATION ...................................
SPECIFICATIONS .................................16
MAINTENANCE ................................
STORAGE........................................22
TROUBLESHOOTING ..............................23
REPLACEMENT PARTS .........................
EMISSION CONTROL WARRANTY ...............
FRANÇAIS ....................................
HOW TO ORDER PARTS ..................BACK PAGE

3
Customer Responsibilities: In additional to complying with all suggested maintenance guidelines and
instructions, customers’ obligations shall include but shall not be limited to: operating the product in accordance
with the owner’s manual or any additional instructions or information provided at the time of purchase or in
subsequent communications to the purchaser from time to time, exhibit reasonable care in the use, operation,
maintenance, general upkeep and storage of the product. Failure to comply with these requirements will void any
applicable warranty.
List of Applicable Warranty Periods: The following list contains the applicable Warranty Period for your
Craftsman product and is based on a combination of the type of product or component and the intended and
actual use of the product or component:
1. 90 days: Craftsman products intended for use or actually used for commercial, institutional, professional or
income-producing purposes
2. 2 years: Craftsman riding lawn mowers, yard and garden tractors, walk behind mowers, tillers, brush
cutters, snow blowers, handheld blowers, backpack blowers, hedge trimmers and electrical products
for noncommercial, nonprofessional, non-institutional, or non-income-producing use, except for those
components which are part of engine systems manufactured by third party engine manufacturers for which the
purchase has received an separate warranty with product information supplied at the time of purchase.
3. 1 year: Craftsman pressure washers, power cutters, stump grinders, pole pruners, gas chain saws, electric
chain saws, trimmer attachments, baggers and pole saws for noncommercial, nonprofessional, non-
institutional, or non-income-producing use.
4. 90 days:
 60 days: Additional Warranty Period of 60 days will apply to adjustments and worn products or components
BUT DOES NOT INCLUDE WEAR OR ADJUSTMENTS for products used for commercial, institutional,
professional or income-producing purposes. Wear items include but are not limited to: belts, blades, tires,

and pulleys.
Service Type:
the service by product type.
Shop Service:
Craftsman walk behind mowers, tillers, brush cutters, handheld blowers, backpack blowers, hedge trimmers,
power cutters, stump grinders, pole pruners, gas chain saws, electric chain saws, trimmer attachments, baggers
and pole saws
At Home Service:
Craftsman riding lawn mowers, yard and garden tractors and snow blowers
As the Warranty Period runs from the date of purchase and NOT from the date that a product is delivered,

assembled and tested for correction operation regardless of when you intend to actually use it. Claims made after
the Warranty Period has expired will not be honored.
Proof of Purchase/Documentation: Warranty coverage is conditioned upon the original purchaser furnishing
Sears Canada or its authorized third party service provider if applicable, with the original sales receipt or other

purchaser is unable to provide a company of the original sales receipt, Sears Canada Inc. reserves the right to

product is acceptable.
SEARS CANADA INC., TORONTO, ONTARIO, CANADA M5B 2C3
Read this manual carefully and become
familiar with your pressure washer. Know
its applications, its limitations, and any
hazards involved.
Important Safety Information
Safety Symbols and Meanings
The safety alert symbol indicates a potential
personal injury hazard. A signal word (DANGER,
WARNING, or CAUTION) is used with the alert symbol
to designate a degree or level of hazard seriousness.
A safety symbol may be used to represent the type of
hazard. The signal word NOTICE is used to address
practices not related to personal injury.
DANGER indicates a hazard which, if not avoided,
will result in death or serious injury.
WARNING indicates a hazard which, if not
avoided, could result in death or serious injury.
CAUTION indicates a hazard which, if not avoided,
could result in minor or moderate injury.
NOTICE address practices not related to personal
injury.
4
SAFETY RULES
Fire
Explosion
Toxic Fumes
Hot Surface
Moving
Parts
Electrical Shock
Slippery Surface
Fall
Kickback
Flying
Objects
Fluid Injection
Operator’s Manual
Chemical
Burn
Projectile
WARNING The engine exhaust from this
product contains chemicals known to the State of
California to cause cancer, birth defects, or other
reproductive harm.
WARNING This product contains lead and lead
compounds, known to the State of California to
cause birth defects or other reproductive harm.
Wash your hands after handling this product.
WARNING Chemical Burn Hazard.
Chemicals could cause burns resulting in
death or serious injury.
DO NOT use caustic liquid with pressure washer.
Use ONLY pressure washer safe detergents/soaps.
Follow all manufacturers instructions.
WARNING POISONOUS GAS HAZARD.
Engine exhaust contains carbon monoxide, a
poisonous gas that could kill you in minutes.
You CANNOT smell it, see it, or taste it.
Even if you do not smell exhaust fumes, you could
still be exposed to carbon monoxide gas.
Some chemicals or detergents could be harmful if
inhaled or ingested, resulting in death, serious injury,
nausea, fainting or poisoning.
Operate this product ONLY outside far away from
windows, doors and vents to reduce the risk of carbon
monoxide gas from accumulating and potentially being
drawn towards occupied spaces.
Install battery-operated carbon monoxide alarms or
plug-in carbon monoxide alarms with battery back-up
according to the manufacturer’s instructions. Smoke
alarms cannot detect carbon monoxide gas.
DO NOT run this product inside homes, garages,
basements, crawlspaces, sheds, or other partially-
enclosed spaces even if using fans or opening doors and
windows for ventilation. Carbon monoxide can quickly
build up in these spaces and can linger for hours, even

ALWAYS place this product downwind and point the
engine exhaust away from occupied spaces.
If you start to feel sick, dizzy, or weak while using this
product, get to fresh air RIGHT AWAY. See a doctor. You
may have carbon monoxide poisoning.
Use a respirator or mask whenever there is a chance that
vapors may be inhaled when using chemicals.
Read all instructions with mask so you are certain the
mask will provide the necessary protection against
inhaling harmful vapors when using chemicals.
WARNING Fuel and its vapors are extremely


resulting in death or serious injury.
WHEN ADDING OR DRAINING FUEL
Turn pressure washer engine OFF and let it cool at least
2 minutes before removing fuel cap. Loosen cap slowly to
relieve pressure in tank.
Fill or drain fuel tank outdoors.
 
If fuel spills, wait until it evaporates before starting engine.
 
heat, and other ignition sources.
 
cracks or leaks. Replace if necessary.
DO NOT light a cigarette or smoke.
WHEN STARTING EQUIPMENT
 
place.
DO NOT crank engine with spark plug removed.
WHEN OPERATING EQUIPMENT
DO NOT operate this product inside any building,
carport, porch, mobile equipment, marine applications, or
enclosure.
DO NOT tip engine or equipment at angle which causes
fuel to spill.
 
WHEN TRANSPORTING, MOVING OR REPAIRING
EQUIPMENT
Transport/move/repair with fuel tank EMPTY or with fuel

DO NOT tip engine or equipment at angle which causes
fuel to spill.
Disconnect spark plug wire.
WHEN STORING FUEL OR EQUIPMENT WITH FUEL
IN TANK
Store away from furnaces, stoves, water heaters, clothes
dryers, or other appliances that have pilot light or other
ignition source because they could ignite fuel vapors.
WARNING Risk of electrocution.
Contact with power source could cause
electric shock or burn resulting in death or
serious injury.
NEVER spray near power source.
WARNING Starter cord kickback (rapid
retraction) will pull hand and arm toward
engine faster than you can let go which
could cause broken bones, fractures,
bruises, or sprains resulting in serious injury.
 
pressure.
When starting engine, pull cord slowly until resistance is
felt and then pull rapidly to avoid kickback.
After each starting attempt, where engine fails to run,
always point spray gun in safe direction, press red button
and squeeze spray gun trigger to release high pressure.
Firmly grasp spray gun with both hands when using high
pressure spray to avoid injury when spray gun kicks
back.
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected, which
could result in serious injury.
 
as a simple cut.
DO NOT allow CHILDREN to operate pressure washer.
NEVER repair high pressure hose. Replace it.
NEVER repair leaking connections with sealant of any
kind. Replace o-ring or seal.
NEVER connect high pressure hose to nozzle extension.
Keep high pressure hose connected to pump and spray
gun while system is pressurized.
ALWAYS point spray gun in safe direction, press red
button and squeeze spray gun trigger to release high
pressure, every time you stop engine.
NEVER aim spray gun at people, animals, or plants.
DO NOT secure spray gun in open position.
DO NOT leave spray gun unattended while machine is
running.
NEVER use a spray gun which does not have a trigger
lock or trigger guard in place and in working order.
Always be certain spray gun, nozzles and accessories
are correctly attached.
NOTICE High pressure spray could damage fragile
items including glass.
DO NOT point spray gun at glass when using red (0°) spray
tip.
NEVER aim spray gun at plants.
NOTICE Improper treatment of pressure washer
could damage it and shorten its life.
If you have questions about intended use, ask dealer or

NEVER operate units with broken or missing parts, or
without protective housing or covers.
DO NOT by-pass any safety device on this machine.
DO NOT tamper with governed speed.
DO NOT operate pressure washer above rated pressure.
DO NOT modify pressure washer in any way.
Before starting pressure washer in cold weather, check all
parts of the equipment to be sure ice has not formed there.
NEVER move machine by pulling on hoses. Use handle
provided on unit.
This equipment is designed to be used with Sears
authorized parts ONLY. If equipment is used with parts

assumes all risks and liabilities.
6
WARNING Use of pressure washer could
create puddles and slippery
surfaces causing you to fall
resulting in death or serious injury.
Kickback from spray gun could cause you to fall
resulting in death or serious injury.
Operate pressure washer from a stable surface.
The cleaning area should have adequate slopes and
drainage to reduce the possibility of a fall due to slippery
surfaces.
Be extremely careful if you must use the pressure washer

Firmly grasp spray gun with both hands when using high
pressure spray to avoid injury when spray gun kicks
back.
WARNING Unintentional sparking could cause

death or serious injury.
WHEN ADJUSTING OR MAKING REPAIRS TO YOUR
PRESSURE WASHER
Disconnect the spark plug wire from the spark plug and
place the wire where it cannot contact spark plug.
WHEN TESTING FOR ENGINE SPARK
Use approved spark plug tester.
DO NOT check for spark with spark plug removed.
WARNING Starter and other rotating parts
could entangle hands, hair, clothing, or
accessories resulting in serious injury.
NEVER operate pressure washer without protective
housing or covers.
DO NOT wear loose clothing, jewelry or anything that
could be caught in the starter or other rotating parts.
Tie up long hair and remove jewelry.
CAUTION
Excessively high operating speeds
could result in minor injury.
DO NOT tamper with governor spring, links or other
parts to increase engine speed. Pressure washer

governed speed.
DO NOT modify pressure washer in any way.
WARNING Risk of eye or bodily injury.
Spray could splash back or propel
objects resulting in serious injury.
Always wear indirect vented (chemical splash) safety
goggles marked to comply with ANSI Z87.1 when using
or in vicinity of this equipment.
NEVER substitute safety glasses or dry-condition
goggles for indirect vented safety goggles.
Always wear protective clothing such as a long-sleeved
shirt, long pants and close-toed shoes.
NEVER operate pressure washer when barefoot or
wearing sandals or shorts.
WARNING Exhaust heat/gases could ignite
combustibles, structures or damage

death or serious injury.

resulting in serious injury.
DO NOT touch hot parts and AVOID hot exhaust gases.
Allow equipment to cool before touching.
 
pressure washer including overhead.
It is a violation of California Public Resource Code,
Section 4442, to use or operate the engine on any forest-
covered, brush-covered, or grass-covered land unless
the exhaust system is equipped with a spark arrester, as

order. Other states or federal jurisdictions may have
similar laws.
Contact the original equipment manufacturer, retailer,
or dealer to obtain a spark arrester designed for the
exhaust system installed on this engine.
Replacement parts must be the same and installed in the
same position as the original parts.
KNOW YOUR PRESSURE WASHER
Read the Operator’s Manual and safety rules before operating your pressure washer.
Compare the illustrations with your pressure washer to familiarize yourself with the locations of various
controls and adjustments. Save this manual for future reference.
7
FEATURES AND CONTROLS
A - Spray Gun — Controls the application of water onto
cleaning surface with trigger device. Includes trigger lock.
B - Accessory Tray — Provides convenient storage for
accessories, such as gun, nozzle extension, etc.
C - Spray Tips — 
high pressure cleaning applications.
D - Fold Down Handle — Handle and accessory tray fold

E - Recoil Starter — Used for starting the engine manually.
F - Oil Fill/Dipstick — Check, add and drain engine oil here.
G - Automatic Cool Down System Cycles water through
pump when water reaches . Warm
water will discharge from pump onto ground. This system
prevents internal pump damage.
H - Pump — Develops high pressure.
J - High Pressure Outlet — Connection for high pressure
hose.
K - Water Inlet — Connection for garden hose.
L - Bottle Bracket
bracket here. Concentrate bottle not included.
M - Air Filter
out of intake air.
N - Engine Switch — Sets engine in starting mode for recoil
starter and stops a running engine.
P - PerfectMix™ Detergent Siphon Tube — Mixes
concentrate with pressure washer spray.
Q - Warning/Operating Instructions Tag
hazards and proper procedure to start/stop pressure
washer.
R - Fuel Tank — Fill tank with regular unleaded fuel. Always
leave room for fuel expansion.
S - High Pressure Hose — Connect one end to water pump
and the other end to spray gun.
T - Nozzle Extension with Quick Connect — Allows you to

Items Not Shown:
Identication Label — Provides model and serial number
of pressure washer. Please have these readily available if
calling for assistance.
B
A
C
D
R
P
J
L
S
Q
T
M
N
K
E
F
H
G
Your pressure washer requires some assembly and is
ready for use only after it has been properly serviced
with the recommended oil and fuel.
If you have any problems with the assembly of
your pressure washer, please call the pressure
washer helpline at 1-800-222-3136.
UNPACK THE PRESSURE WASHER
1. Remove everything from carton except pressure
washer.
2. Open carton completely by cutting each corner
from top to bottom.
3. Remove pressure washer from carton.
CARTON CONTENTS
Check all contents. If any parts are missing or
damaged, call the pressure washer helpline at
1-800-222-3136.
Main Unit
• Handle
Accessory Tray
High Pressure Hose
Spray Gun
Nozzle Extension with Quick Connect Fitting
Bottle Bracket Wireform
PerfectMix™ Detergent Siphon Tube/Unit
Oil Pouch
Parts Bag (which includes the following):
Operator’s Manual
Owner’s Registration Card
Rubber Straps (2)
Ba g containing 4 multi–colored Spray Tips
Handle Fastening Hardware Kit (which
includes):
Handle Bolts (2)
Carriage Bolt (1)
Plastic Knobs for Handle (2)
Plastic Knob (1)
Tree Clips (4)
Become familiar with each piece before assembling
the pressure washer. Identify all contents with the
illustration on page 7. If any parts are missing or
damaged, call the pressure washer helpline at
1-800-222-3136.
ASSEMBLING PRESSURE WASHER
Your Craftsman pressure washer will need assembly
before operation:
1. Fill out and send in registration card.
2. Attach handle and accessory tray.
3. Connect detergent siphon tube to pump.
4. Add oil to engine crankcase.
 
6. Connect pressure hose to spray gun and pump.
7. Connect water supply to pump.
8. Attach nozzle extension to spray gun.
 
extension.
Attach Handle and Accessory Tray
1. Place handle (A) onto handle supports connected
to main unit. Make sure holes in handle align with
holes on handle supports.
2. Insert handle carriage bolts (B) through holes from
inside of unit and attach a plastic knob (C) from
outside of unit. Tighten by hand.
NOTICE By loosening both knobs to the middle
section of the attachment bolt, the upper handle can

fold the handle down while the engine is hot.
3. Insert rubber straps (D) through slots (E) in back of
accessory tray and pull tight from front.
8
ASSEMBLY
C
B
A
E
D
4. Place accessory tray (A) over holes (B) on handle
(viewing from front of unit). Push the tree clips
(C
accessory tray.
 
other supplied accessories in spaces provided in
accessory tray. See How to Use Accessory Tray.
6. Attach bottle bracket (D) to handle with carriage bolt
(E) and black plastic knob (F). Tighten by hand.
Attach PerfectMix™ Detergent Siphon to
Pump
Attach the tube end of the blue PerfectMix™ detergent
siphon (GH) on the pump.
Attach PerfectMix™ Detergent Siphon to
Concentrate Bottle
Place PerfectMix™ bottle (not included) in the wire-
form bracket on the handle. Remove cap from bottle
and insert the PerfectMix™ detergent siphon. Screw
the detergent siphon unit to the top of the bottle (J).
Use the clip on the cap (K) to snap detergent siphon
tube to wire form bracket when detergent siphon tube
is not in a concentrate bottle.
Add Engine Oil
 
 
cap/dipstick.
3. Hold neck of supplied oil pouch and remove cap.
 

mark (top hole) on dipstick.
NOTICE Pause to permit oil to settle. Wipe dipstick

NOTICE Improper treatment of pressure washer
could damage it and shorten its life.
DO NOT attempt to crank or start the engine before it has
been properly serviced with the recommended oil. This
could result in an engine failure.
 
Add Fuel
Fuel must meet these requirements:
Clean, fresh, unleaded gasoline.
 
altitude use, see High Altitude.
Gasoline with up to 10% ethanol (gasohol) is
acceptable.
NOTICE Use of unapproved fuels could damage
pressure washer and voids warranty.
 
DO NOT mix oil in gasoline or modify engine to run on
alternate fuels.
A
C
B
G
H
J
K
E
D
F
WARNING Fuel and its vapors are extremely


resulting in death or serious injury.
WHEN ADDING FUEL
Turn pressure washer engine OFF and let it cool at least
2 minutes before removing fuel cap. Loosen cap slowly to
relieve pressure in tank.
Fill fuel tank outdoors.
 
If fuel spills, wait until it evaporates before starting engine.
 
heat, and other ignition sources.
 
cracks or leaks. Replace if necessary.
DO NOT light a cigarette or smoke.
Full
Add
To protect the fuel system from gum formation, mix in a
fuel stabilizer when adding fuel. See Storage. All fuel is
not the same. If you experience starting or performance


operate on gasoline. The emission control system for

 
2. Slowly add regular unleaded fuel (A) to fuel
tank (B

tank neck.
3. Install fuel cap and wait for any spilled fuel to
evaporate.
CAUTION! Alcohol-blended fuels (called gasohol,
ethanol or methanol) can attract moisture, which leads
to separation and formation of acids during storage.
Acidic gas can damage the fuel system of an engine
while in storage.
To avoid engine problems, the fuel system should be
treated with a fuel preserver or emptied before storage


tank will promote fuel deterioration during storage. If
fuel preserver is not used, drain the fuel tank, start the
engine and let it run until the fuel lines and carburetor
are empty. Use fresh fuel next season. See Storage for
additional information.
NEVER use engine or carburetor cleaner products in
the fuel tank as permanent damage may occur.
High Altitude


remain emissions compliant, high altitude adjustment is
required. Operation without this adjustment will cause
decreased performance, increased fuel consumption,

for high altitude adjustment information. Operation of

high altitude kit is not recommended.
Lubricate O-Rings
Lubrication of o-rings is extremely important for
installation and operation. The use of a lubricant
(petroleum or synthetic grease) during assembly helps
seat o-rings properly and provides an improved seal. It
also helps protect the o-ring from damage by abrasion,
pinching or cutting and extends the life of the o-ring.
NOTICE ALWAYS apply a small amount of lubricant
on o-rings prior to assembling the garden hose to the
pump (C), high pressure hose (D), spray gun (E), and
nozzle extension (F).
Lubricate all connections shown below, following
these instructions:
1. Inspect and clean connecting surfaces prior to
lubrication and assembly.
2. Use lubricants sparingly during assembly; a light

3. Use a small brush or cotton swab to apply grease
directly to o-rings where they are not accessible

10
B
A
F
E
C
D
11
Connect Hose and Water Supply to Pump
NOTICE DO NOT run the pump without the water
supply connected and turned on.
Damage to equipment resulting from failure to follow this
instruction will void warranty.
NOTICE Remove and discard the shipping caps from
the pump’s high pressure outlet and water inlet before
attaching hoses.
1. Uncoil high pressure hose and attach one end of
hose to base of spray gun. Tighten by hand.
2. Attach other end of high pressure hose to high
pressure outlet on pump. Tighten by hand.
3. Before connecting garden hose to water inlet,
inspect inlet screen (A). Clean screen if it contains
debris or have it replaced if damaged. DO NOT
run pressure washer if inlet screen is damaged
or missing.
4. Run water through your garden hose for
30 seconds to clean out any debris.
NOTICE DO NOT siphon standing water for the water
supply. Use ONLY cold water (less than 100°F).
NOTICE Using a One Way Valve (vacuum breaker
or check valve) at pump inlet could cause pump or
inlet connector damage.
There MUST be at least 10 ft. (3 m) of unrestricted garden
hose between the pressure washer inlet and any device,
such as a vacuum breaker or check valve.
Damage to equipment resulting from failure to follow this
instruction will void warranty.
 
length) to the water inlet. Tighten by hand.
6. Turn ON the water, press red button (B) on the
gun and squeeze the trigger to purge the pump
system of air and impurities.
Checklist Before Starting Engine
Review the unit to ensure you have performed all of
the following:
1. Be sure to read Safety Rules and Operation
sections before using the pressure washer.
2. Make sure handle is in place and secure.
3. Check that oil has been added to proper level in
engine crankcase.
4. Add proper fuel to fuel tank.
 
and water supply) and that there are no kinks,
cuts, or damage to the high pressure hose.
6. Provide proper water supply (not to exceed
100°F).
B
A
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
NEVER connect high pressure hose to nozzle extension.
Keep high pressure hose connected to pump and spray
gun while system is pressurized.
Always be certain spray gun, nozzles and accessories
are correctly attached.
WARNING Risk of eye injury.
Spray could splash back or propel objects
resulting in serious injury.
Always wear indirect vented (chemical splash) safety
goggles marked to comply with ANSI Z87.1 when using
or in vicinity of this equipment.
NEVER substitute safety glasses or dry-condition
goggles for indirect vented safety goggles.
HOW TO USE YOUR PRESSURE
WASHER
If you have any problems operating your pressure
washer, please call the pressure washer helpline at
1-800-222-3136.
Pressure Washer Location
Carbon Monoxide Poisoning
Risk of Fire Clearances
How To Start Your Pressure Washer
To start your engine-powered pressure washer for the

information also applies whenever you start the engine
after you have let the pressure washer sit idle for at
least a day.
1. Place pressure washer outside near an water

greater than 3.3 GPM (gallons per minute) and
no less than 20 PSI (pounds per square inch) at
pressure washer end of garden hose.
2. Check that high pressure hose is tightly connected
to spray gun and pump. See Assembly for
illustrations.
3. Make sure unit is in a level position.
4. Connect garden hose to water inlet on pressure
washer pump.
NOTICE DO NOT run the pump without the water
supply connected and turned on.
Damage to equipment resulting from failure to follow this
instruction will void warranty.
 
squeeze the trigger to purge the pump system of air
and impurities.
6. Attach nozzle extension to spray gun. Tighten by
hand.
7. Choose spray tip you want to use and insert it into
nozzle extension. See How to Use Spray Tips.
8. Push engine rocker switch (A) to ON (I) position.
OPERATION
12
A
WARNING POISONOUS GAS HAZARD.
Engine exhaust contains carbon monoxide,
a poisonous gas that could kill you in
minutes. You CANNOT smell it, see it, or
taste it. Even if you do not smell exhaust fumes, you
could still be exposed to carbon monoxide gas.
Operate this product ONLY outside far away from
windows, doors and vents to reduce the risk of carbon
monoxide gas from accumulating and potentially being
drawn towards occupied spaces.
Install battery-operated carbon monoxide alarms or
plug-in carbon monoxide alarms with battery back-up
according to the manufacturer’s instructions. Smoke
alarms cannot detect carbon monoxide gas.
DO NOT run this product inside homes, garages,
basements, crawlspaces, sheds, or other partially-
enclosed spaces even if using fans or opening doors and
windows for ventilation. Carbon monoxide can quickly
build up in these spaces and can linger for hours, even

ALWAYS place this product downwind and point the
engine exhaust away from occupied spaces.
If you start to feel sick, dizzy, or weak while using this
product, get to fresh air RIGHT AWAY. See a doctor. You
may have carbon monoxide poisoning.
WARNING Exhaust heat/gases could ignite
combustibles, structures or damage fuel tank

injury.
 
pressure washer including overhead.
Exhaust Port
Pointed away from
occupied spaces
13
NOTICE Before starting the pressure washer, be sure
you are wearing safety goggles as described below.
NOTICE This unit is equipped with a ReadyStart®
engine. A ReadyStart® engine means there is no
priming or choking required.
 
recommended and grasp starter grip handle and
pull slowly until you feel some resistance. Then pull
rapidly to start engine.
10. Return recoil starter slowly. DO NOT let rope “snap
back” against starter.
11. Point spray gun in a safe direction, push the red
button to release the trigger lock, and pull the
trigger.
How to Stop Your Pressure Washer
1. Release spray gun trigger and let engine idle for
two minutes.
2. Push engine rocker switch to OFF (0) position.
3. ALWAYS point spray gun in a safe direction,
push red button and squeeze spray gun trigger to
release retained high water pressure.
WARNING Risk of eye injury.
Spray could splash back or propel objects
resulting in serious injury.
Always wear indirect vented (chemical splash) safety
goggles marked to comply with ANSI Z87.1 when using
or in vicinity of this equipment.
NEVER substitute safety glasses or dry-condition goggles
for indirect vented safety goggles.
WARNING Starter cord kickback (rapid
retraction) will pull hand and arm toward
engine faster than you can let go which could
cause broken bones, fractures, bruises, or
sprains resulting in serious injury.
 
pressure.
When starting engine, pull cord slowly until resistance is
felt and then pull rapidly to avoid kickback.
After each starting attempt, where engine fails to run,
always point spray gun in safe direction, press red button
and squeeze spray gun trigger to release high pressure.
Firmly grasp spray gun with both hands when using high
pressure spray to avoid injury when spray gun kicks back.
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected, which
could result in serious injury.
DO NOT allow CHILDREN to operate pressure washer.
Keep high pressure hose connected to pump and spray
gun while system is pressurized.
NEVER aim spray gun at people, animals, or plants.
DO NOT secure spray gun in open position.
DO NOT leave spray gun unattended while machine is
running.
NEVER use a spray gun which does not have a trigger
lock or trigger guard in place and in working order.
Always be certain spray gun, nozzles and accessories are
correctly attached.
WARNING Exhaust heat/gases could ignite
combustibles, structures or damage

death or serious injury.

resulting in serious injury.
DO NOT touch hot parts and AVOID hot exhaust gases.
Allow equipment to cool before touching.
 
pressure washer including overhead.
It is a violation of California Public Resource Code,
Section 4442, to use or operate the engine on any forest-
covered, brush-covered, or grass-covered land unless
the exhaust system is equipped with a spark arrester, as

order. Other states or federal jurisdictions may have
similar laws.
Contact the original equipment manufacturer, retailer, or
dealer to obtain a spark arrester designed for the exhaust
system installed on this engine.
Replacement parts must be the same and installed in the
same position as the original parts.
How to Use Accessory Tray
The unit is equipped with an accessory tray with places
to store your spray gun, nozzle extension and quick
connect spray tips. There are also hooks at the back of
the accessory tray to wrap your high pressure hose.
1. Place one end of high pressure hose in groove at
top of accessory tray and wrap high pressure hose
around hooks as shown.
2. Place nozzle extension in groove on accessory tray
as shown. Pull rubber strap tight around nozzle
extension and place hole in strap over tab on
accessory tray.
3. Place spray gun in groove on accessory tray as
shown. Pull rubber strap tight around spray gun and
place hole in strap over tab on accessory tray.
4. Insert multi–colored spray tips in holes provided on
front of accessory tray.
How to Use Spray Tips
The quick–connect on the nozzle extension allows you

tips. Spray tips can be changed while pressure washer
is running once spray gun trigger lock is engaged. The
spray tips vary the spray pattern as shown.
Follow these instructions to change spray tips:
1. Pull back collar on quick–connect and pull current

the accessory tray.
2. Select desired spray tip:
For delicate rinse, select white 40° spray tip.
 
For maximum rinsing, select red 0° spray tip.
To apply detergent, select black detergent
spray tip.
3. Pull back on collar, insert new spray tip and release
collar. Tug on spray tip to make sure it is securely in
place.
Usage Tips
 
8 to 24 inches (20 to 61 cm) away from cleaning
surface.
If you get spray tip too close, especially using a high
pressure spray tip, you may damage surface being
cleaned.
DO NOT
cleaning tires.
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
NEVER exchange spray tips without the trigger lock being
engaged on the spray gun.
DO NOT twist spray tips while spraying.
14
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected, which
could result in serious injury.
Keep high pressure hose connected to pump and spray
gun while system is pressurized.
ALWAYS point spray gun in safe direction, press red
button and squeeze spray gun trigger to release high
pressure, every time you stop engine.
40° White
2100 PSI
2.3 GPM

2300 PSI
2.2 GPM
0° Red
2700 PSI
2.1 GPM
Black
Use to apply
detergent
Low Pressure
High Pressure

Cleaning and Applying Detergent
To apply detergent, follow these steps:
1. Review use of spray tips.
2. Attach Perfect Mix™ detergent siphoning tube to
concentrate bottle.
NOTICE Make sure tube is fully submerged in
detergent while applying detergent.
NOTICE 
detergent siphoning tube.
When inserting siphon into a detergent solution bottle, route
tube so as to keep it from inadvertently contacting the hot

3. Make sure black spray tip is installed.
NOTICE Detergent cannot be applied with high
pressure spray tips (White, Yellow or Red).
4. Make sure garden hose is connected to water inlet.
Check that high pressure hose is connected to
spray gun and pump. Turn on water.
NOTICE You must attach all hoses before you start the
engine.
Starting the engine without all the hoses connected and
without the water turned ON could damage the pump.
Damage to equipment resulting from failure to follow this
instruction will void warranty.
 How to Start
Your Pressure Washer.
6. Apply detergent to a dry surface, starting at lower
portion of area to be washed and work upward,
using long, even, overlapping strokes.
 
washing and rinsing. Reapply as needed to prevent
surface from drying. DO NOT allow detergent to
dry on (prevents streaking).
NOTICE 
system after each use by placing the tube into a bucket
of clean water, then run the pressure washer in low
pressure for 1-2 minutes.
Pressure Washer Rinsing
For Rinsing:
1. Remove black spray tip from nozzle extension.
2. Select and install desired high pressure spray tip
following instructions How to Use Spray Tips.
3. Keep the spray gun a safe distance from the area
you plan to spray.
4. Apply a high pressure spray to a small area and
then check surface for damage. If no damage
is found, you can assume it is okay to continue
rinsing.
 
with same overlapping strokes as you used for
cleaning.
Cleaning Detergent Siphoning Tube
If you used the detergent siphoning tube, you must

1. Place detergent siphoning tube in a bucket full of
clean water.
2. Remove high pressure spray tip from nozzle
extension.
3. Select and install black detergent spray tip
following instructions How to Use Spray Tips.
4. Flush for 1-2 minutes.
 How to
Stop Pressure Washer
6. ALWAYS point spray gun in a safe direction push
red button and squeeze spray gun trigger to
release retained high water pressure.
Automatic Cool Down System (Thermal
Relief)
If you run the engine on your pressure washer for

spray gun, circulating water in the pump can reach

system engages to cool the pump by discharging the
warm water onto the ground.
WARNING Chemical Burn Hazard.
Chemicals could cause burns resulting in
death or serious injury.
DO NOT use caustic liquid with pressure washer.
Use ONLY pressure washer safe detergents/soaps.
Follow all manufacturers instructions.
WARNING Kickback from spray gun could
cause you to fall resulting in death or serious
injury.
Operate pressure washer from a stable surface.
Be extremely careful if you must use the pressure washer

Firmly grasp spray gun with both hands when using high
pressure spray to avoid injury when spray gun kicks back.
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected, which
could result in serious injury.
Keep high pressure hose connected to pump and spray
gun while system is pressurized.
ALWAYS point spray gun in safe direction, press red
button and squeeze spray gun trigger to release high
pressure, every time you stop engine.
ENGINE TECHNICAL INFORMATION
This is a single cylinder, L-head, air cooled engine.
In the State of California, Model 110000 engines are


does not grant the purchaser, owner or operator of
this engine any additional warranties with respect to
the performance or operational life of this engine. The
engine is warranted solely according to the product and
emissions warranties stated elsewhere in this manual.
Power Ratings
The gross power rating for individual gasoline engine
models is labeled in accordance with SAE (Society

Power & Torque Rating Procedure, and is rated in

derived at 2600 RPM for those engines with “rpm”
called out on the label and 3060 RPM for all others;
horsepower values are derived at 3600 RPM.
The gross power curves can be viewed at www.
BRIGGSandSTRATTON.COM. Net power values are
taken with exhaust and air cleaner installed whereas
gross power values are collected without these
attachments. Actual gross engine power will be higher

things, ambient operating conditions and engine-to-
engine variability. Given the wide array of products on
which engines are placed, the gasoline engine may not
develop the rated gross power when used in a given

variety of factors including, but not limited to, the variety
of engine components (air cleaner, exhaust, charging,
cooling, carburetor, fuel pump, etc.), application
limitations, ambient operating conditions (temperature,
humidity, altitude), and engine-to engine variability.
Due to manufacturing and capacity limitations, Briggs &
Stratton may substitute an engine of higher rated power
for this engine.
PRODUCT SPECIFICATIONS
Pressure Washer Specications
Max Outlet Pressure.........2,700 PSI* @ 2.1 GPM
Max Flow Rate .............2,100 PSI @ 2.3 GPM*
Detergent Mix ....................Use as directed
Water Supply Temperature .....Not to exceed 100°F
Engine Specications
Bore ........................... 
Stroke .......................... 
Displacement .....................
Spark Plug
Type: ..................

Set Gap To: .................
Armature Air Gap: ......
Valve clearance with valve springs installed and piston
1/4 in. (6 mm) past top dead center (check when engine
is cold).
Intake ................ 0.004-0.008 in.(0.10-0.20 mm)
Exhaust ............... 0.004-0.008 in.(0.10-0.20 mm)
Fuel Capacity ........................... 1.6 Quarts
Oil Capacity ................... 20 Ounces (0.6 liter)
NOTICE For practical operation, the engine load

will decrease 3-1/2% for each 1,000 ft. (300 m) above



* This pressure washer is rated in accordance to
the Pressure Washer Manufacturers Association
(PWMA) standard PW101-2010 (Testing and Rating
Performance of Pressure Washers).
This spark ignition system complies with the Canadian
standard ICES-002.
SPECIFICATIONS
16
17
Maintenance Schedule
Follow the hourly or calendar intervals, whichever

operating in adverse conditions noted below.
1
Clean if clogged. Replace if perforated or torn.
2
Service more often under dirty or dusty conditions.
General Recommendations
Regular maintenance will improve the performance and
extend the life of the pressure washer. See any Sears

The pressure washer warranty does not cover items
that have been subjected to operator abuse or
negligence. To receive full value from the warranty, the
operator must maintain pressure washer as instructed
in this manual including proper storage as detailed in
Storage.
Some adjustments will need to be made periodically to
properly maintain your pressure washer.
All service and adjustments should be made at least

assure proper fuel-air mixture and help your engine run
better and last longer. Follow the requirements in the
Maintenance Schedule chart above.
Pump Oil
DO NOT attempt any oil maintenance on this pump.
The pump is pre-lubricated and sealed from the
factory, requiring no additional maintenance for the life
of the pump.
Emissions Control
Maintenance, replacement, or repair of the
emissions control devices and systems may
be performed by any non-road engine repair
establishment or individual. However, to obtain
”no charge” emissions control service, the work must
be performed by a factory authorized dealer. See the
Emissions Warranty.
Before Each Use
1. Check engine oil level.
2. Clean debris.
3. Check water inlet screen for damage.
4. Check high pressure hose for leaks.
 
6. Check gun and nozzle extension assembly for
leaks.
7. Purge pump of air and contaminants.
PRESSURE WASHER MAINTENANCE
Clean Debris
Daily or before use, clean accumulated debris from
pressure washer. Keep linkage, spring and controls

any combustible debris. Inspect cooling air slots and
openings on the pressure washer. These openings
must be kept clean and unobstructed.
Pressure washer parts should be kept clean to reduce
the risk of overheating and ignition of accumulated
debris.
Use a damp cloth to wipe exterior surfaces clean.
NOTICE Improper treatment of pressure washer
could damage it and shorten its life.
DO NOT insert any objects through cooling slots.
Use a soft bristle brush to loosen caked on dirt, oil,
etc.
Use a vacuum cleaner to pick up loose dirt and
debris.
Check and Clean Inlet Screen
Examine garden hose inlet screen. Clean if it is
clogged or replace if it is torn.
MAINTENANCE
First 5 Hours
Change engine oil
Every 8 Hours or Daily
Check/clean water inlet screen
1
Check high pressure hose
Check detergent siphoning tube
Check spray gun and assembly for leaks
Clean debris
Check engine oil level
Every 50 Hours or Yearly
Clean engine air cleaner
2
Change engine oil
2
 
Every 200 Hours or Yearly
Replace engine air cleaner
2
Yearly
Replace spark plug
Clean cooling system
2
Check High Pressure Hose
High pressure hoses can develop leaks from wear,
kinking, or abuse. Inspect hose before each use.
Check for cuts, leaks, abrasions, bulging of cover, or
damage or movement of couplings. If any of these
conditions exist, replace hose immediately.
Check Detergent Siphoning Tube
Examine detergent tube and clean if clogged. The tube

for leaks or tears. Replace the tube if damaged.
Detergent Siphoning Check Ball
Occasionally check ball in detergent siphoning
system may become stuck from storage, dried soap,
or minerals in water. The check ball can be freed by
performing the following:
NOTICE Before performing this procedure, be sure
you are wearing safety goggles as described below.
 
2. ALWAYS point spray gun in a safe direction,
press red button and squeeze spray gun trigger to
release retained high water pressure.
3. Remove detergent siphoning hose from barbed

 
smaller, by at least 1” long, such as an Allen
wrench, slowly insert the object into the barbed

the check ball.
 
slightly, push no more than 1/8”. Slight pressure
may be required to free the ball.
 
7. Reinstall detergent siphoning hose onto barb

8. Treat with PumpSaver as described in Protecting
the Pump during storage to prevent reoccurrence.
Check Spray Gun and Nozzle Extension
Examine hose connection to spray gun and make sure
it is secure. Test trigger by pressing it and making sure
it springs back into place when you release it. Do not
depress red button and test trigger. You should not be
able to press trigger. Replace spray gun immediately if it
fails any of these tests.
Spray Tip Maintenance
A pulsing sensation felt while squeezing the spray gun
trigger may be caused by excessive pump pressure.
The principal cause of excessive pump pressure is a
spray tip clogged or restricted with foreign materials,
such as dirt, etc. To correct the problem, immediately
clean the spray tip following these instructions:
 
2. ALWAYS point spray gun in a safe direction, press
red button and and squeeze spray gun trigger to
release retained high water pressure.
3. Remove spray tip from end of nozzle extension.
4. Use a small paper clip to free any foreign material
clogging or restricting spray tip (A).
WARNING Risk of eye injury.
Spray could splash back or propel objects
resulting in serious injury.
Always wear indirect vented (chemical splash) safety
goggles marked to comply with ANSI Z87.1 when using
or in vicinity of this equipment.
NEVER substitute safety glasses or dry-condition
goggles for indirect vented safety goggles.
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected, which
could result in serious injury.
Keep high pressure hose connected to pump and spray
gun while system is pressurized.
ALWAYS point spray gun in safe direction, press red
button and squeeze spray gun trigger to release high
pressure, every time you stop engine.
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected, which
could result in serious injury.
Keep high pressure hose connected to pump and spray
gun while system is pressurized.
ALWAYS point spray gun in safe direction, press red
button and squeeze spray gun trigger to release high
pressure, every time you stop engine.
A
18
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
NEVER repair high pressure hose. Replace it.
Replacement hose rating MUST equal or exceed
maximum pressure rating of unit.

 
6. Using a garden hose, remove additional debris by


7. Reinstall spray tip into nozzle extension.
8. Reconnect nozzle extension to spray gun.
 
Check that high pressure hose is connected to
spray gun and pump. Turn on water.
10. Start engine following instructions How to Start
Your Pressure Washer.
11. Test pressure washer by operating with each quick
connect spray tip.
O–Ring Maintenance
Purchase an O–Ring Repair Kit at your local Sears or
by calling 1-800-4-MY-HOME (469-4663) or online
at www.sears.ca. It is not included with the pressure
washer. This kit includes replacement o-rings, rubber

sheet provided in the kit to service your unit’s o-rings.
ENGINE MAINTENANCE
Oil
Oil Recommendations
We recommend the use of Briggs & Stratton Warranty


SF, SG, SH, SJ or higher. DO NOT use special
additives.
Outdoor temperatures determine the proper oil
viscosity for the engine. Use the chart to select the best
viscosity for the outdoor temperature range expected.
* Below 40°F (4°C) the use of SAE 30 will result in hard
starting.
** Above 80°F (27°C) the use of 10W30 may cause increased
oil consumption. Check oil level more frequently.
Checking Oil Level
Oil level should be checked prior to each use or at least
every 8 hours of operation. Keep oil level maintained.
1. Make sure pressure washer is on a level surface.
2. Remove oil dipstick and wipe dipstick with clean
cloth. Replace and tighten dipstick. Remove and
and check oil level.
3. Verify oil is at FULL mark (top hole) on dipstick.
Replace and tighten dipstick.
Adding Engine Oil
1. Make sure pressure washer is on a level surface.
2. Check oil level as described in Checking Oil Level.
 

NOTICE 
not start, or hard starting.
 
If over the FULL mark on dipstick, drain oil to reduce oil
level to FULL mark on dipstick.
4. Replace and tighten dipstick.
Changing Engine Oil
If you are using your pressure washer under extremely
dirty or dusty conditions, or in extremely hot weather,
change oil more often.
Full
Add
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
NEVER repair leaking connections with sealant of any
kind. Replace o-ring or seal.
WARNING Unintentional sparking could cause

death or serious injury.
WHEN ADJUSTING OR MAKING REPAIRS TO YOUR
PRESSURE WASHER
Disconnect the spark plug wire from the spark plug and
place the wire where it cannot contact spark plug.
WHEN TESTING FOR ENGINE SPARK
Use approved spark plug tester.
DO NOT check for spark with spark plug removed.
CAUTION Avoid prolonged or repeated skin
contact with used motor oil.
Used motor oil has been shown to cause skin cancer in
certain laboratory animals.
Thoroughly wash exposed areas with soap and water.
KEEP OUT OF REACH OF CHILDREN.
DON’T POLLUTE. CONSERVE
RESOURCES. RETURN USED OIL TO
COLLECTION CENTERS.
Change oil while engine is still warm from running,
as follows:
1. Drain fuel tank by running pressure washer until
fuel tank is empty.
2. Disconnect spark plug wire and keep it away from
spark plug.
 
dipstick. Wipe dipstick clean.
 
into a suitable container making sure you tip your
unit away from spark plug. When crankcase is
empty, return pressure washer to upright position.
 

FULL mark (top hole) on dipstick.
6. Wipe dipstick clean each time oil level is checked.
DO NOT 
7. Replace and tighten dipstick.
8. Wipe up any remaining oil.
 
Service Air Cleaner
Your engine will not run properly and may be damaged
if you run it with a dirty air cleaner. Service more
often if operating under dirty or dusty conditions.
Replacements are available at your local Sears service
center.
To service the air cleaner, follow these steps:
1. Slide air cleaner lever (A) to unlock (
) position
and tilt cover (B) down.
2. Carefully remove air cleaner to prevent debris from
falling into carburetor.
3. Wash foam air cleaner (C) in liquid detergent and
water. Squeeze dry in a clean cloth.
4. SATURATE foam air cleaner in engine oil and
squeeze in a clean cloth to remove excess oil.
 
base (D).
6. Tilt cover up and slide lever to lock (
) position.
NOTICE 
calling 1-800-4-MY-HOME (469-4663).
Service Spark Plug
Changing the spark plug will help your engine to start
easier and run better.
1. Clean area around spark plug.
2. Remove and inspect spark plug.
3. Replace spark plug if electrodes are pitted, burned
or porcelain is cracked. Use the recommended
replacement plug. See Specications.
4. Check electrode gap with wire feeler gauge and
reset spark plug gap to recommended gap if
necessary (see Specications).
 
NOTICE You can purchase a new spark plug by
calling 1-800-4-MY-HOME (469-4663).
Inspect Muer and Spark Arrester

damage. Remove the spark arrester, if equipped, and
inspect for damage or carbon blockage. If replacement
parts are required, make sure to use only original
equipment replacement parts.
D
C
B
A
WARNING Exhaust heat/gases could ignite
combustibles, structures or damage

death or serious injury.

resulting in serious injury.
DO NOT touch hot parts and AVOID hot exhaust gases.
Allow equipment to cool before touching.
 
pressure washer including overhead.
It is a violation of California Public Resource Code,
Section 4442, to use or operate the engine on any forest-
covered, brush-covered, or grass-covered land unless
the exhaust system is equipped with a spark arrester, as

order. Other states or federal jurisdictions may have
similar laws.
Contact the original equipment manufacturer, retailer, or
dealer to obtain a spark arrester designed for the exhaust
system installed on this engine.
Replacement parts must be the same and installed in the
same position as the original parts.
20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60

Simplicity 020532-01 Manuel utilisateur

Catégorie
Nettoyeurs haute pression
Taper
Manuel utilisateur

dans d''autres langues