LG DLEY1701WE Le manuel du propriétaire

FRANÇAISENGLISH

OWNER’S MANUAL

DRYER

Read this owner’s manual thoroughly before operating the appliance

and keep it handy for reference at all times.

DLEY1701*E, DLGY1702*E

DLEY1701*, DLGY1702*

MFL67652510

www.lg.com

MFL67652510_en_170713.indd 1 2017-07-13 오전 11:27:26

2

TABLE OF CONTENTS

3

PRODUCT FEATURES

4

SAFETY INSTRUCTIONS

5 IMPORTANT SAFETY INSTRUCTIONS

7 GROUNDING INSTRUCTIONS

8

PRODUCT OVERVIEW

8 Parts

8 Accessories

8 Two-Way Reversible Door (on some models)

8 Safety Tether Kit (on some models)

9

INSTALLATION

9 Installation Overview

9 Product Specifications

10 Installation Location Requirements

10 Clearances

11 Installing on a pedestal

12 Leveling the Dryer

12 Reversing the Door

20 Installing the Side Vent Kit

21 Venting the Dryer

24 Connecting Gas Dryers

26 Connecting Electric Dryers

30 Final Installation Check

31 Installation Test (Duct Check)

33

OPERATION

33 Using the Dryer

34 Check the Lint Filter Before Every Load

34 Sorting Loads

34 Loading the Dryer

35 Using the LG EasyLoad

TM

36 Control Panel

38 Cycle Guide

39 Cycle Settings and Options

42 Steam Functions (Steam Models)

43

SMART FEATURES

43 Tag On (on some models)

49

MAINTENANCE

49 Regular Cleaning

50

TROUBLESHOOTING

50 FAQs: Frequently Asked Questions

50 User Support Videos

51 Before Calling for Service

58

SMART DIAGNOSIS™

58 Using Smart Diagnosis

TM

59

WARRANTY (CANADA)

MFL67652510_en_170713.indd 2 2017-07-13 오전 11:27:26

3

PRODUCT FEATURES

ENGLISH

PRODUCT FEATURES

Easy-to-Use Control Panel

An entire selection of user-friendly functions make operating the dryer easy.

Two-way Easy-access Reversing Door

The LG EasyLoad

TM

can be tilted open from the top, hamper-style, allowing you to easily load the dryer without items falling

on the floor. The door still swings open to provide easy access for unloading or loading of bulkier items. The door hinge can

be reversed to adjust to the installation location.

Steam Functions (Steam Models)

LG's steam technology allows you to inject fabrics with a swirling jet of steam to refresh clothes, reduce static, and make

ironing easier. Simply select the Steam Fresh

TM

cycle or Wrinkle Care cycle.

Flow Sense

TM

Duct Blockage Sensing System Indicator

The Flow Sense

TM

duct blockage sensing system detects and alerts you to restrictions in the installed household ductwork

that reduce exhaust airflow through the dryer. If you see the alert: Clean or repair the ducts to remove the restrictions. Keep

your ducts free of blockage to help increase efficiency and reduce long drying times caused by blocked ducts.

Smart Diagnosis

TM

Should you experience any technical difficulty with your dryer, it has the capability of transmitting data via your telephone

to the Customer Information Center. The call center agent records the data transmitted from your machine and uses it to

analyze the issue, providing a fast and effective diagnosis.

Tag On (on some models)

The Tag On feature works on most smart phones equipped with the NFC function and based on the Android operating

system (OS).

Using the LG Smart Laundry & DW application, the Tag On feature will allow you to diagnose your appliance, download new

cycles, and see the status of your appliance by simply touching the smart phone to the Tag On logo of the appliance.

Protocol P154

Sanitization Performance of

Residential Clothes dryer

C

E

R

T

I

F

I

E

D

E

S

I

G

N

Protocol P154

Sanitization Performance of

Residential Clothes dryer

C

E

R

T

I

F

I

E

D

E

S

I

G

N

Protocol P154

Sanitization Performance of

Residential Clothes dryer

C

E

R

T

I

F

I

E

D

E

S

I

G

N

MFL67652510_en_170713.indd 3 2017-07-13 오전 11:27:26

4

SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

Your safety and the safety of others is very important.

We have provided many important safety messages in this manual and on your appliance. Always read and

obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word DANGER, WARNING, or

CAUTION.

These words mean:

DANGER

-

You will be killed or seriously injured if you

do not

immediately follow instructions.

WARNING

- You may be killed or seriously injured if you do not follow instructions.

CAUTION

- You may be slightly injured or cause damage to the product if you do not follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury,

and tell you what may happen if the instructions are not followed.

WARNING – Risk of Fire

Install the clothes dryer according to the manufacturer’s instructions and local codes.

•

Do not install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type) duct is installed,

it must be of a specific type identified by the appliance manufacturer as suitable for use with clothes dryers.

Flexible venting materials are known to collapse, be easily crushed, and trap lint. These conditions will obstruct

clothes dryer airflow and increase the risk of fire.

•

To reduce the risk of severe injury or death, follow all installation instructions.

•

Save these instructions.

WARNING

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious injury, death or property damage.

—Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other

appliance.

—WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Clear the room, building or area of all occupants.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

—Installation and service must be performed by a qualified installer, service agency or the gas supplier.

MFL67652510_en_170713.indd 4 2017-07-13 오전 11:27:26

5

SAFETY INSTRUCTIONS

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS

WARNING

To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic

precautions, including the following:

Installation

•

Keep area around the exhaust opening and

adjacent surrounding areas free from the

accumulation of lint, dust, and dirt.

•

Do not install or store this appliance where it will be

exposed to the weather.

•

Do not place items exposed to cooking oils in

your dryer. Items contaminated with cooking oils

may contribute to a chemical reaction that could

cause a load to catch fire.

•

Properly ground the dryer to conform with all

governing codes and ordinances. Follow the

details in the installation instructions. Electric shock

may result if the dryer is not properly grounded.

•

Before use, the dryer must be properly installed

as described in this manual. Electric shock may

result if the dryer is not properly grounded.

•

Install and store the dryer where it will not be

exposed to temperatures below freezing or exposed

to the weather.

•

All repairs and servicing must be performed by

authorized service personnel unless specifically

recommended in this Owner’s Manual. Use only

authorized factory parts. Failure to follow this

warning may result in serious injury, fire, electric

shock, or death.

•

To reduce the risk of electric shock, do not

install the dryer in humid spaces. Failure to

follow this warning may result in serious injury, fire,

electric shock, or death.

•

Connect to a properly rated, protected, and

sized power circuit to avoid electrical overload.

Improper power circuits may melt, creating electric

shock and/or fire hazard.

•

Remove all packing items and dispose of all

shipping materials properly. Failure to do so may

result in burns, fire, explosion, or death.

•

Place the dryer at least 18-inch above the floor

for a garage installation. Failure to do so may

result in burns, fire, explosion, or death.

•

Keep all packaging from children. Packaging

material can be dangerous for children. There is a

risk of suffocation.

•

Do not install near another heat source such

as a stove, oven or heater. Failure to follow this

warning may result in product deformation, smoke,

or fire.

•

Do not place candles, smoking materials, or other

flammables on top of the product. Dripping wax,

smoke, or fire may result.

•

Remove all protective vinyl film from the

product. Failure to do so may result in product

damage, smoke, or fire.

•

Gas dryers MUST be exhausted to the outside.

Failure to follow these instructions may result in fire

or death.

•

The dryer exhaust system must be exhausted to the

outside of the dwelling. If the dryer is not exhausted

outdoors, some fine lint and large amounts of

moisture will be expelled into the laundry area. An

accumulation of lint in any area of the home may

create a health and fire hazard.

•

Use only rigid, semi-rigid or flexible metal 4-inch

diameter duct inside the dryer cabinet or for

exhausting to the outside. Use of plastic or other

combustible ductwork may cause fire. Punctured

ductwork may cause fire if it collapses or becomes

otherwise restricted in use or during installation.

•

Ductwork is not provided with the dryer, and

you should obtain the necessary ductwork

locally. The end cap should have hinged

dampers to prevent backdraft when the dryer is

not in use. Failure to follow these instructions may

result in fire or death.

•

The exhaust duct must be 4-inch (10.2 cm) in

diameter with no obstructions. The exhaust

duct should be kept as short as possible. Make

sure to clean any old ducts before installing

your new dryer. Failure to follow these instructions

may result in fire or death.

•

Rigid, semi-rigid or flexible metal ducting is

recommended for use between the dryer and

the wall. All non-rigid metal transition duct

must be UL-listed. Use of other materials for

transition duct could affect drying time. Failure

to follow these instructions may result in fire or

death.

•

Do not use sheet metal screws or other

fasteners which extend into the duct that could

catch lint and reduce the efficiency of the

exhaust system. Secure all joints with duct tape.

For complete details, follow the Installation

Instructions. Failure to follow these instructions

may result in fire or death.

MFL67652510_en_170713.indd 5 2017-07-13 오전 11:27:26

6

SAFETY INSTRUCTIONS

Operation

•

Read all instructions before using the appliance.

•

Do not dry articles that have been previously

cleaned in, washed in, soaked in, or spotted with

gasoline, dry-cleaning solvents, or other flammable

or explosive substances, as they give off vapors

that could ignite or explode.

•

Do not reach into the appliance if the drum is

moving.

•

Do not allow children to play on or in the appliance.

Close supervision of children is necessary when

the appliance is used near children.

•

Do not use fabric softeners or products to eliminate

static unless recommended by the manufacturer of

the fabric softener or product.

•

Do not use heat to dry articles containing foam

rubber or similarly textured rubber-like materials.

•

Do not tamper with controls.

•

Always check the inside of the dryer for foreign

objects. Failure to follow these instructions may

result in fire or death.

•

Do not store plastic, paper, or clothing that may

burn or melt on top of the dryer during operation.

Failure to follow these instructions may result in fire

or death.

•

Be careful when opening and closing the door.

Fingers and hands can get caught in the door and

cause injury if the door drops forward unexpectedly.

•

Do not place heavy items on or lean against the

top of the door when it is open.

•

Do not attempt to pull the hamper door open

more than 40 degrees.

•

The dryer could tip forward, causing injury or

damage.

•

Do not place items on the top of the dryer.

•

Gas appliances can cause minor exposure to four

of these substances, namely benzene, carbon

monoxide, formaldehyde, and soot, caused

primarily by the incomplete combustion of natural

gas or LP fuels.

•

Properly adjusted dryers will minimize incomplete

combustion. Exposure to these substances can be

minimized further by properly venting the dryer to

the outdoors.

SAVE THESE INSTRUCTIONS

Steam (steam model):

•

Do not open the dryer door during steam

cycles. Failure to follow these instructions may

result in a burn hazard.

•

Do not dry articles that have been previously

cleaned in, washed in, soaked in, or spotted

with gasoline, dry-cleaning solvents, or other

flammable or explosive substances as they give

off vapors that could ignite or explode. Failure to

follow these instructions may result in fire or death.

•

Do not fill the steam feeder with gasoline,

dry cleaning solvents, or other flammable or

explosive substances. Failure to follow these

instructions may result in fire or death.

•

Do not touch the steam nozzle in the drum

during or after the steam cycles. Failure to follow

these instructions may result in a burn hazard.

•

Do not fill the steam feeder with hot water (over

86 °F/30 °C). Failure to follow these instructions

may result in a burn hazard.

Maintenance

•

Do not repair or replace any part of the appliance

or attempt any servicing unless specifically

recommended in the user maintenance instructions

or in published user-repair instructions that you

understand and have the skills to carry out.

•

Clean the lint filter before or after each load.

•

The interior of the appliance and exhaust duct

should be cleaned periodically by qualified service

personnel.

•

Before the appliance is removed from service

or discarded, remove the door to the drying

compartment.

WARNING

Fire Hazard

Failure to follow safety warnings exactly could

result in serious injury, death or property damage.

Do not install a booster fan in the exhaust duct.

Install all clothes dryers in accordance with the

installation instructions of the manufacturer of the

dryer.

MFL67652510_en_170713.indd 6 2017-07-13 오전 11:27:26

7

SAFETY INSTRUCTIONS

ENGLISH

GROUNDING INSTRUCTIONS

WARNING

Improper connection of the equipment-grounding conductor may result in a risk of electric shock.

Check with a qualified electrician or service person if you are in doubt that the appliance is properly

grounded.

•

This appliance must be grounded. In the event

of malfunction or breakdown, grounding will reduce

the risk of electric shock by providing a path of least

resistance for electric current.

•

This appliance must be equipped with a cord

having an equipment-grounding conductor and

a grounding plug. The plug must be plugged into

an appropriate outlet that is properly installed and

grounded in accordance with all local codes and

ordinances.

•

Do not modify the plug. If it will not fit the outlet,

have a proper outlet installed by a qualified

electrician.

•

This appliance must be connected to a

grounded metal, permanent wiring system or

an equipment-grounding conductor must be

run with the circuit conductors and connected

to the equipment-grounding terminal or lead

on the appliance. Electric shock may result if the

dryer is not properly grounded.

•

The dryer should always be plugged into its

own individual electrical outlet which has a

voltage rating that matches the rating plate. This

provides the best performance and also prevents

overloading house wiring circuits which can cause

a fire hazard from overheated wires.

•

Never unplug your dryer by pulling on the

power cord. Always grip the plug firmly and pull

straight out from the outlet. The power cord may

be damaged, resulting in a risk of fire and electric

shock.

•

Repair or replace immediately all power

cords that have become frayed or otherwise

damaged. Do not use a cord that shows cracks

or abrasion damage along its length or at either

end. The power cord may melt, creating electric

shock and/or fire hazard.

•

When installing or moving the dryer, be careful

not to pinch, crush, or damage the power cord.

This will prevent injury and damage to the dryer

from fire and electric shock.

•

Do not, under any circumstances, cut or

remove the ground prong from the power cord.

To prevent personal injury or damage to the dryer,

the electrical power cord must be plugged into a

properly grounded outlet.

•

For personal safety, this dryer must be properly

grounded. Failure to do so may result in electric

shock or injury.

•

Refer to the installation instructions in this

manual for specific electrical requirements for

your model. Failure to follow these instructions

may create an electric shock hazard and/or a fire

hazard.

•

This dryer must be plugged into a properly

grounded outlet. Electrical shock may result if

the dryer is not properly grounded. Have the

wall outlet and circuit checked by a qualified

electrician to make sure the outlet is properly

grounded. Failure to follow these instructions

may create an electric shock hazard and/or a fire

hazard.

MFL67652510_en_170713.indd 7 2017-07-13 오전 11:27:26

8

PRODUCT OVERVIEW

Parts

Control

panel

Leveling

feet

Reversible

door

Power cord

location

(gas models)

Water inlet valve

(on some models)

Exhaust duct

outlet

Terminal block

access panel

(electric models)

Gas connection

location

(gas models)

Lintlter

Accessories Two-Way Reversible Door

(on some models)

Included Accessories

Optional accessories

Y connector

(steam models)

Hoses

(steam

models)

Drying rack

Side vent kit

(sold separately)

Kit No. 383EEL9001B

Safety Tether

Kit

(on some

models)

Pedestal or Pedestal Washer

(sold separately)

Release

Hamper

door

Swing door

The LG EasyLoad™ feature allows you to open

the dryer door from the top, hamper-style, when

loading the dryer to help guide clothes into the drum

and prevent them from falling onto the floor. When

unloading the dryer or loading bulkier items, use the

swing door for easy access to the drum.

Safety Tether Kit (on some models)

This optional kit helps prevent the dryer tipping if children climb on the door or if someone should fall onto the

door. It is recommended that you install this kit, depending on your situation, but it is not required. Follow the

customer installation instructions included with the kit to properly install the kit. If you do not install the kit, store it

out of reach of children.

NOTE

•

For your safety and for extended product life, use only authorized components. The manufacturer is not

responsible for product malfunction or accidents caused by the use of separately purchased unauthorized

components or parts.

•

The images in this guide may be different from the actual components and accessories, which are subject

to change by the manufacturer without prior notice for product improvement purposes.

MFL67652510_en_170713.indd 8 2017-07-13 오전 11:27:27

9

INSTALLATION

ENGLISH

INSTALLATION

Installation Overview

Please read the following installation instructions first after purchasing this product or transporting it to another

location.

Check and choose

the proper location

Connect the inlet hose

(steam models)

Connect gas dryers

Connect electric dryers

Plug in the power cord Installation test Test run

Gas dryer Electric dryer

Level the dryer

Vent the dryer

Product Specifications

The appearance and specifications listed in this manual may vary due to constant product improvements.

Dryer Models DLEY1701*E, DLGY1702*E DLEY1701*, DLGY1702*

Description Steam Dryer

Electrical requirements Please refer to the rating label regarding detailed information.

Gas requirements

NG: 4–10.5-inch WC

LP: 8–13-inch WC

Max. water pressure 20–120 psi (138–827 kPa)

Dimensions

27” (W) X 28 15/16” (D) X 40 3/16” (H), 50 1/4” (D with door open)

68.6 cm (W) X 73.4 cm (D) X 102 cm (H), 127.5 cm (D with door open)

Net weight

Gas dryer : 136 lb (61.7 kg) –138 lb (62.6 kg)

Electric dryer : 133.5 lb (60.6 kg) –134.5 lb (61.0 kg)

Drying capacity

- Normal cycle IEC 7.3 cu.ft. (22.5 lb/10.2 kg)

MFL67652510_en_170713.indd 9 2017-07-13 오전 11:27:27

10

INSTALLATION

Installation Location Requirements

WARNING

Read all installation instructions completely before installing and operating your dryer! It is important that you

review this entire manual before installing and using your dryer. Detailed instructions concerning electrical

connections, gas connections, and exhaust requirements are provided on the following pages.

The installation requires:

•

A location that allows for proper exhaust installation. A gas dryer must be exhausted to the outdoors. See

Venting the Dryer.

•

A grounded electrical outlet located within 2 ft. (61 cm) of either side of the dryer. See Connecting Electric

Dryers .

•

A sturdy floor to support the total dryer weight of 200 lb (90.7 kg). The combined weight of a companion

appliance should also be considered.

•

No other fuel-burning appliance can be installed in the same closet as a dryer.

Do not operate your dryer at temperatures below 45 °F (7 °C). At lower temperatures, the dryer might not shut off

at the end of an automatic cycle. This can result in longer drying times. The dryer must not be installed or stored

in an area where it will be exposed to water and/or weather. Check code requirements. Some codes limit, or do

not permit, installation of the dryer in garages, closets, mobile homes or sleeping quarters. Contact your local

building inspector.

NOTE

•

The floor must be level, with a maximum slope of 1 inch (2.5 cm) under the entire dryer. Clothes may not

tumble properly, and automatic sensor cycles may not operate correctly if dryer is not level.

•

For a garage installation, you will need to place the dryer at least 18-inch (46 cm) above the floor. The

standard pedestal is 15-inch. You will need 18-inch (46 cm) from the garage floor to the bottom of the

dryer.

Clearances

Installation Spacing for Recessed Area or Closet Installation

The following spacing dimensions are recommended for this dryer. This dryer has been tested for clearances of

1 inch (2.5 cm) on the sides and rear. Recommended clearances should be considered for the following reasons:

•

Additional clearances should be considered for ease of installation and servicing.

•

Additional clearances might be required for wall, door and floor moldings.

•

Additional clearances should be considered on all sides of the dryer to reduce noise transfer.

For closet installation, with a door, minimum ventilation openings in the top and bottom of the door are

required. Louvered doors with equivalent ventilation openings are acceptable.

•

Companion appliance spacing should also be considered.

MFL67652510_en_170713.indd 10 2017-07-13 오전 11:27:27

11

INSTALLATION

ENGLISH

Closet Ventilation Requirements

Closets with doors must have both an upper and lower vent to prevent heat and moisture buildup in the closet.

One upper vent opening with a minimum opening of 48 sq. in. (310 cm

2

) must be installed no lower than 6 feet

above the floor. One lower vent opening with a minimum opening of 24 sq. in. (155 cm

2

) must be installed no

more than one foot above the floor. Install vent grills in the door or cut down the door at the top and bottom to

form openings. Louvered doors with equivalent ventilation openings are also acceptable.

NOTE

There should be at least a little space around the dryer (or any other appliance) to eliminate the transfer of

vibration from one appliance to another. If there is enough vibration, it could cause appliances to make noise

or come into contact, causing paint damage and further increasing noise.

Installation Spacing for Recessed Area or Closet

Closet Door Vent

Requirements

3"

(7.6 cm)

14" max.*

(35.6 cm)

1"

(2.5 cm)

1"

(2.5 cm)

27"

(68.6 cm)

3"

(7.6 cm)

5"**

(12.7 cm)

50

1

/

4

"

(127.5 cm)

28

15

/

16

"

(73.4 cm)

18" min.

(45.7 cm)

21

1

/

4

"

(54 cm)

48 in.

2

(310 cm

2

)

24 in.

2

(155 cm

2

)

* Required spacing

** For side or bottom venting, 2-inch (5.1 cm) of spacing is allowed

Installation Spacing for Cabinet Installing on a pedestal

For cabinet installation with a door, minimum ventila-

tion openings in the top of the cabinet are required.

* Required spacing

28

15

/

16

"

(73.4 cm)

5"

(12.7 cm)

NOTE

Refer to the instructions packaged with the

optional PEDESTAL before installing with a

PEDESTAL.

7"

*

(17.8 cm) 7"

*

(17.8 cm)

5"

*

(12.7 cm)

1"

(2.5 cm)

1"

(2.5 cm)

1"

*

(2.5 cm)

28

15

/

16

"

(73.4 cm)

27"

(68.6 cn)

MFL67652510_en_170713.indd 11 2017-07-13 오전 11:27:28

12

INSTALLATION

Leveling the Dryer

WARNING

To reduce the risk of injury to persons, adhere

to all industry recommended safety procedures

including the use of long-sleeved gloves and

safety glasses. Failure to follow this warning may

result in serious injury or death.

•

The appliance is heavy. Two or more people

are required when installing the dryer. Failure to

follow this warning may result in serious injury

or death.

•

To ensure that the dryer provides optimal drying

performance, it must be level. To minimize

vibration, noise, and unwanted movement, the

floor must be a perfectly level, solid surface.

NOTE

Adjust the leveling feet only as far as necessary

to level the dryer. Extending the leveling feet more

than necessary may cause the dryer to vibrate.

1

Position the dryer in the final location. Check

levelness of dryer from side to side. Repeat from

front to back

Place level here

Not Level Not LevelLevel

2

Use an adjustable wrench to turn the leveling

feet. Unscrew the legs to raise the dryer or

screw in the legs to lower it. Raise or lower with

the leveling feet until the dryer is level from side

to side and front to back. Make sure that all four

leveling feet are in firm contact with the floor.

•

All four leveling feet must rest solidly on the

floor. Gently push on the top corners of the

dryer to make sure that the dryer does not

rock from corner to corner.

If you are installing the dryer on the optional pedestal,

you must use the leveling feet on the pedestal to

level the dryer. The dryer leveling feet should be fully

retracted.

Reversing the Door

Before you Begin

NOTE

Service calls to reverse the door are not

covered under the product warranty.

•

The door reversal process for the two-way door

is more complex than for a conventional dryer

door. Read through these instructions in their

entirety before beginning the process, in order

to gauge whether to have the procedure done

by a professional installer or service person.

•

A support video is also provided at http://www.

lg.com/us/support/videos/video-tutorials-view,

How to Reverse the Door – LG EasyLoad™

Dryer.

MFL67652510_en_170713.indd 12 2017-07-13 오전 11:27:28

13

INSTALLATION

ENGLISH

Swing door

1

Open the door and remove the two plastic hole

caps on the catch side by gently prying up with a

flat blade screwdriver. Save these for step 6.

Hole cap

2

While supporting the door, remove the 4 screws,

two from each hinge. Set the door aside face

down on a protected surface to prevent damage

to the door or the work surface.

Hinge screw

WARNING

The edges of the door cover may be sharp. Take

care when handling, or wear gloves to avoid

injury.

3

With the door on a protected surface, remove

the 16 screws on each side of the door and

lift off the inner door frame using a flat blade

screwdriver. Remove the latch hook and blank

and install them on the opposite side.

Latch hook

Blank

Inner door

frame

4

Remove the 4 screws securing the hinges to

the door frame. Remove the two plastic cover

caps. Reinstall the hinges and cover caps on the

opposite sides from which they were removed.

Cover cap

Hinge

assembly

Tools Required

•

Phillips screwdriver

•

Large flat blade screwdriver (recommended

for hinge screws if they are tight or your Phillips

screwdriver is worn)

•

Small flat blade screwdriver (for lifting out parts)

WARNING

THE DRYER DOOR IS VERY LARGE AND

HEAVY. Failure to follow the instructions below

may result in damage to the dryer, property

damage or personal injury.

•

To avoid damage to the dryer or the door,

support the door with a stool or box that fits

under the door, or have an assistant support

the weight of the door.

•

Avoid dropping the door to avoid damage to the

door or the floor.

•

Unplug the dryer or turn off power at the main

circuit breaker before beginning door reversal.

Door Reversal Instructions

NOTE

The instructions here are for changing the door

swing from a right to a left side hinge. If the

door has been reversed, and it is necessary to

change it back, use care when following these

instructions. Some of the illustrations and the left/

right references will be reversed, and you will

need to read the instructions carefully.

WARNING

Be sure to support the weight of the door before

removing the hinge screws.

MFL67652510_en_170713.indd 13 2017-07-13 오전 11:27:28

14

INSTALLATION

5

With the hinges and cover caps in the new

locations, remount the inner door frame onto the

outer door frame with the screws removed in

step 3 above.

WARNING

Be sure to support the weight of the door before

installing the hinge screws.

6

Reinstall the door with the screws removed in

step 2. Install the two plastic hole caps removed

in step 1 on the opposite side.

Hamper door (on some models)

The door reversal procedure consists of four main

parts:

•

Removing and reinstalling the door and hinges

(steps 1, 2, and 20)

•

Removing and reversing components on the dryer

cabinet (step 3)

•

Removing and reversing components on the door

cover (steps 4 and 5)

•

Removing and reversing components inside the

door (steps 6 through 19)

1

Open the door from the side so that the hinge

screws are accessible.

Two large

screws

Two small

screws

2

Remove the four hinge screws

While supporting the door, remove the four hinge

screws, two from each hinge. Set the door aside

face down on a protected surface to prevent

damage to the door or the work surface.

3

Reverse the components on the cabinet.

a. Use a Phillips screwdriver to remove the two

screws and the latch mechanism on the front

panel of the cabinet.

Upper

hinge

Hinge

cover

Hinge

latch

mechanism

Latch

hole

cover

Hinge

bracket

b. Remove the latch hole cover by gently prying it

up with a flat blade screwdriver, being careful

not to scratch the paint. Install the latch hole

cover on the opposite side, where the latch

mechanism was removed. Install the latch

mechanism in the position from which you

removed the latch hole cover, using the two

screws removed in step a.

c. Remove the hinge cover by gently prying it up

with a flat blade screwdriver, being careful not

to scratch the paint. Rotate the hinge cover

180 degrees and install it on the opposite side,

where the upper hinge was attached.

Upper

hinge

Hinge

cover

Hinge

latch

mechanism

Latch

hole

cover

Hinge

bracket

d. Reverse the hinge and the hinge bracket at

the bottom of the cabinet. Remove the two

screws from the hinge bracket at the bottom

right and remove the hinge bracket. Remove

the lower of the two screws behind the hinge

bracket. Do NOT remove the upper screw

behind the hinge bracket. Set the parts aside.

MFL67652510_en_170713.indd 14 2017-07-13 오전 11:27:29

15

INSTALLATION

ENGLISH

CAUTION

Do NOT remove any of the eight screws on the

face of the cabinet (marked below). Doing so

could result in damage to the dryer and the need

for a service call to repair the dryer.

e. Remove the three screws on the hinge at the

bottom left. Remove the hinge and reinstall it

on the right side. The top screw will occupy

the hole where you removed the screw behind

the hinge bracket in step d.

f. Install the hinge bracket removed in step d on

the bottom left side, first installing one screw

behind the hinge bracket.

ON THE DOOR:

4

Lift off the door cover.

With the door laid inside facing up on a protected

surface, remove the twelve screws on the inside

of the door. Carefully lift off the door cover with

the help of a small flat blade screwdriver inserted

in the upper corner (circled below).

WARNING

The edges of the door cover may be sharp. Take

care when handling, or wear gloves to avoid

injury.

Hole

plug

Twelve screws

Interlock

button

5

Switch the door strike and the blank cover.

Remove the four screws on the door cover that

secure the door strike and the blank cover.

Switch the door strike and the blank cover,

installing them on the opposite sides from which

they were removed.

Long

screw

Long

screw

Short

screws

Blank cover Door strike

Gently pry out the hole plug on the side of

the door cover and install it in the hole on the

opposite side.

Hole

plug

Set the door cover aside.

MFL67652510_en_170713.indd 15 2017-07-13 오전 11:27:29

16

INSTALLATION

6

Reverse the components inside the door.

You will now be removing and reversing various components inside the door. See below for a detailed

diagram and identification of the inner structure and parts of the door. (The diagram shows the “before view”

of the door, with the default set-up for a right side hinge swing. After following these instructions, your door

should be a mirror image of the illustration.)

Upper

hingelter

Side lock rod

Side Interlock button

Lower

hingeller

Lower

hinge

bracket

Bumpers

Inner lock rodsTop interlock buttons

Top lock rod

Upper

hinge

assembly

Upper

hinge pivot

Glass

Lower

hinge

assembly

Interlock buttons

Inner lock rods

Lowhingeller

Lower hinge bracket

Top lock rod

Lower hinge assembly

Side lock rod

Hole plug

MFL67652510_en_170713.indd 16 2017-07-13 오전 11:27:30

17

INSTALLATION

ENGLISH

7

Lift out the two top interlock buttons.

Lift out the two grey interlock buttons from the

top of the outer door and set them aside for later

use.

Interlock buttons

Side

lock rod

8

Lift out the grey interlock button in the side

of the door.

Make sure to remove the spring with the

interlock button and to keep the two together.

Set the interlock button aside. Do not confuse

these with the interlock buttons from the top of

the outer door.

9

Remove the side lock rod.

Remove the side lock rod from the lower hinge

bracket by lifting the top end of the rod and

sliding it toward the top of the door. The spring

should remain attached to the lock rod. Set the

lock rod aside.

Spring

10

Remove the top lock rod.

a. Slide the lock rod to the right to remove it from

the hinge assembly on the left side.

b. While sliding the lock rod right, lift the right end

up and out of the guides.

Do not remove the two inner lock rods (see page

16) located underneath the top lock rod. They

do NOT need to be reversed.

NOTE

11

Remove the upper hinge pivot.

Once the top lock rod has been removed, the

hinge pivot can easily be removed from the

hinge assembly on the upper left and set aside.

Upper hinge

assembly

Upper

hinge

pivot

12

Reverse the upper hinge assembly and

hinge filler.

Lift out the upper hinge filler (on the right) and

set it aside.

Carefully lift the upper hinge assembly (on the

left) out of the outer door frame, using a small

flat blade screwdriver if necessary. Rotate

the hinge assembly 180 degrees and install it

on the upper right side of the outer door. You

will need to press firmly to install the hinge

assembly.

The hinge pivot removed in step 11 will be

installed later.

Upper hinge assembly

Upper hinge pivot

Now rotate the hinge filler 180 degrees and

install it on the upper left side of the door.

Upperhingeller

MFL67652510_en_170713.indd 17 2017-07-13 오전 11:27:31

18

INSTALLATION

13

Reinstall the top lock rod.

Rotate the top lock rod (removed in step 10)

180 degrees end for end from its original

position and reinstall it. The spring should now

be to the right of center, with the spring on the

side of the rod facing the top of the door.

a. Insert the right end of the lock rod into the

right hinge assembly. Make sure the rod is

aligned with the guides in the door panel.

b. Lower the rod into position, sliding it to

bypass the center handle, making sure to

align the lock rod with the guides all the

way across the door panel. When released,

the lock rod should slide completely into

the hinge assembly on the right. Slide the

lock rod back and forth to make sure it is

correctly positioned in the guides and slides

easily.

14

Reverse the lower hinge bracket and hinge

assembly.

a. Remove the screw from the lower hinge

bracket (on the right) and lift the hinge

bracket out. Set it aside. Remove the two

screws from the lower hinge assembly on

the bottom left and lift the hinge assembly

out.

b. Rotate the lower hinge assembly 180

degrees and install it on the right side using

the two screws removed in step a.

Lower hinge assembly

Screws

c. Flip over the lower hinge bracket and

release the tabs on the back locking the

hinge filler to the hinge bracket.

Tab

d. Rotate the hinge 180 degrees and snap

it back onto the front of the hinge bracket

facing in the opposite direction.

e. Mount the lower hinge bracket and the filler

on the left side of the door with the screw

removed in step a.

Screw

15

Install the side lock rod.

Flip the side lock rod over and install it on the

opposite side. Insert the lower end into the left

hinge and lower the rod into the guides on the

door while compressing the spring inside the

recess.

Make sure the top of the side lock rod is

beside the top lock rod and the two do not

overlap each other, so the two rods can

interact correctly. If they are not aligned

properly, the door will not operate properly.

MFL67652510_en_170713.indd 18 2017-07-13 오전 11:27:32

19

INSTALLATION

ENGLISH

16

Reinstall the top interlock buttons.

Reinstall the top gray interlock buttons

removed in step 7, one on each side of the

outer door panel.

17

Reinstall the side interlock button.

Reinstall the side interlock button removed in

step 8. Center the spring in the compartment

and insert the interlock button on top of it.

18

Reinstall the door cover.

Clean the glass on the door and door cover, if

necessary.

Make sure the three gray interlock buttons

are properly installed and that the top and

side lock rods are properly aligned where

they meet. Carefully lower the door cover into

place, aligning the holes in the cover with

the interlock buttons on the top and side and

the bumpers on the bottom. Take care not to

dislodge the lock rods while mounting the door

cover. Once the door cover is in place, secure

it with the 12 screws removed in step 4. The

ten similar screws go around the top and sides

of the door cover. Make sure to install the two

different screws on the bottom edge, in the

locations marked below.

Interlock

buttons

Bumpers

19

Now, pick up the upper hinge pivot

removed earlier and rotate it 180 degrees.

Press in the side interlock button on the left

side and hold it down while you press the

hinge pivot into the hinge assembly on the top

right side. If the door has been reassembled

correctly, the lock rod will slide back easily and

lock the pivot in place. The door is now ready

to remount on the opposite side of the dryer.

WARNING

Be sure to support the weight of the door before

installing the hinge screws.

20

Reinstall the door.

While supporting the door, install the four

hinge screws removed in step 2. Test the

swing of the door to make sure the hinges and

latch are properly aligned and that the door

opens, closes and latches properly in both

directions.

Two

large

screws

Two

small

screws

MFL67652510_en_170713.indd 19 2017-07-13 오전 11:27:32

20

INSTALLATION

Installing the Side Vent Kit

WARNING

•

Use a heavy metal vent.

•

Do not use plastic or thin foil ducts.

•

Clean old ducts before installing this dryer.

•

To reduce the risk of injury to persons, adhere

to all industry recommended safety procedures

including the use of long-sleeved gloves and

safety glasses.

•

Failure to follow all of the safety warnings in this

manual could result in property damage, injury

to persons, or death.

Your new dryer is shipped to vent to the rear. It can

also be configured to vent to the bottom or side (right-

side venting is not available on gas models).

An adapter kit, part number 383EEL9001B, may be

purchased from your LG retailer. This kit contains the

necessary duct components to change the dryer vent

location.

1

Remove the rear exhaust duct retaining screw.

Pull out the exhaust duct.

Retaining Screw

Rear Exhaust

Duct

Option 1: Side Venting

2

Press the tabs on the knockout and carefully

remove the knockout for the desired vent

opening (right-side venting is not available on

gas models). Press the adapter duct onto the

blower housing and secure to the base of the

dryer as shown.

Adapter

Duct

Bracket

Knockout

3

Preassemble a 4-inch (10.2 cm) elbow to the

next 4-inch (10.2 cm) duct section, and secure

all joints with duct tape. Be sure that the male

end of the elbow faces AWAY from the dryer.

Insert the elbow/duct assembly through the

side opening and press it onto the adapter duct.

Secure it in place with duct tape. Be sure that

the male end of the duct protrudes 1½-inch (3.8

cm) to connect the remaining ductwork. Attach

the cover plate to the back of the dryer with the

included screw.

Cover

Plate

Elbow

1

½

"

(3.8 cm)

Option 2: Bottom Venting

2

Press the adapter duct onto the blower housing

and secure it to the base of the dryer as shown.

Adapter

Duct

Bracket

3

Insert the 4-inch (10.2 cm) elbow through the

rear opening and press it onto the adapter duct.

Be sure that the male end of the elbow faces

down through the hole in the bottom of the

dryer. Secure it in place with duct tape. Attach

the cover plate to the back of the dryer with the

included screw.

Cover

Plate

Elbow

MFL67652510_en_170713.indd 20 2017-07-13 오전 11:27:32

La page charge ...

LG DLEY1701WE Le manuel du propriétaire

Ce manuel convient également à

LG DLEY1701WE Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents