Simplicity SEARS CRAFTSMAN SNOWTHROWER Manuel utilisateur

SEARS CANADA INC., TORONTO, ONTARIO M5B 2B8 11/2008

Owner’s

Manual

Model

C950-52843-0

13.5 T.P. 27 inch

CAUTION:

You must read and

understand this owner’s

manual before operating

unit.

Serial No. ______________

DUAL STAGE

SNOWTHROWER

1736810

, Rev. B

Not for

Reproduction

RULES FOR SAFE OPERATION

2

General Information

This instruction book is written for a person with some mechanical ability.

Like most service books, not all the steps are described. Steps on how to

loosen or tighten fasteners are steps anyone can follow with some

mechanical ability. Read and follow these instructions before you use the

unit.

Know your product: If you understand the unit and how the unit

operates, you will get the best performance. As you read this manual,

compare the illustrations to the unit. Learn the location and the function of

the controls. To help prevent an accident, follow the operating instructions

and the safety rules. Keep this manual for future reference.

IMPORTANT: Many units are not assembled and are sold in cartons. It is

the responsibility of the owner to make sure the assembly instructions in

this manual are exactly followed. Other units are purchased in an

assembled condition. On assembled units, it is the responsibility of the

owner to make sure the unit is correctly assembled. The owner must

carefully check the unit according to the instructions in this manual before

it is first used.

This manual contains safety information to make you

aware of the hazards and risks associated with snow

throwers, and how to avoid them. The snow thrower is designed and

intended for removal of snow, and should not be used for any other

purpose. It is important that you read and understand these

instructions, and anyone operating the equipment read and

understand these instructions.

The engine exhaust from this product contains chemicals known to the

State of California to cause cancer, birth defects, or other reproductive

harm.

WARNING

A signal word (DANGER, WARNING, or CAUTION) is used with the alert

symbol to indicate the likelihood and the potential severity of injury. In

addition, a hazard symbol may be used to represent the type of hazard.

DANGER indicates a hazard which, if not avoided, will result in

death or serious injury.

WARNING indicates a hazard which, if not avoided, could result

in death or serious injury.

CAUTION indicates a hazard which, if not avoided, might result

in minor or moderate injury.

CAUTION, when used without the alert symbol, indicates a

situation that could result in damage to the equipment.

Hazard Symbols and the meanings

These symbols are used on your equipment and defined in your operating

manual. Review and understand the meanings. The use of one of these

symbols combined with a signal word will alert you to potential hazards

and how to avoid them.

Explosion

Toxic fumes

Shock

Hot Surface

Fire

Operator’s Manual ï Read and understand

before performing any activity or running

equipment.

Safety Alert ï Identifies safety information about

hazards that can result in personal injury.

Rotating auger

Rotating impeller

Rotating gears

Thrown objects

Keep a safe distance

from the equipment.

Shut off engine and

remove spark plug

connector before

performing maintenance

or repair work.

Never reach into

rotating parts.

Recommended ear

protection for

extended use.

Not for

Reproduction

RULES FOR SAFE OPERATION

3

Operating Symbols and their meanings

These symbols are used on your equipment and defined in your operating

manual. It is important that you review and understand the meanings.

Failure to understand the symbols might result in harm to you.

Stop

Fuel

Choke off

Oil

Choke on

Slow

Fast

On Off

Ignition Key

Ignition Off

Ignition On

Primer bulb

Throttle

Drive Clutch

Auger Clutch

Engage

RIGHT

Auger Collector

Traction

Discharge Chute

PUTFEL DOWN

Forward

Neutral

Reverse

Push to engage

electric start

Electric

Start

Engine

Start

Engine Run

Engine Off

Chute Deflector

Engage

Disengage

Heated Grips

Avoid death or serious injury from rotating auger.

Keep hands, feet and clothing away.

Unclogging discharge chute is a hazardous activity.

Stop engine and disconnect spark plug wire when performing maintenance

on equipment.

Never leave the equipment unattended while engine is running. Always

disengage the auger and traction controls, stop engine, and remove keys.

Keep children, pets, and others out of the area during operation. Children

are often attracted to the equipment. Be mindful of all persons present.

Keep all loose clothing far away from front of snow thrower and auger.

Scarves, mittens, dangling drawstrings, loose clothes and pants can

quickly become caught in the rotating device and dismemberment will

occur. Tie up long hair and remove jewelry.

The snow thrower is intended to remove snow only. Do not use for

purposes other than what is intended.

Do not clear snow across the face of slopes. Exercise extreme caution when

changing direction on slopes. Do not attempt to clear steep slopes.

Do not use the snow thrower on surfaces above ground level such as roofs

of residences, garages, porches or other such structures or buildings.

DANGER

Discharge chute contains rotating impeller to throw snow.

Never clear or unclog discharge chute with your hands, or

while engine is running.

Fingers can quickly become caught and traumatic

amputation or severe laceration can result.

Unclogging the discharge chute is a hazardous activity. Clogged or

blocked augers store energy and can rotate unexpectedly.

Never place hands in or near discharge chute.

With engine OFF, wait for all moving parts to cease movement, then with a

stick, clear the chute. Even with engine off, parts may rotate and

dismemberment can occur.

Clogged snow can hide other obstructions in the chute and cause damage

to the equipment, impeller or auger. Take precautions when restating the

equipment after snow removal.

DANGER

Not for

Reproduction

RULES FOR SAFE OPERATION

4

Objects can be picked up by auger and thrown from chute.

Never throw snow toward people or cars, and never allow

anyone in front of the snow thrower.

•Be aware of your environment while operating equipment. Running over

items such as, gravel, doormats, newspapers, toys, and rocks hidden

under snow, can all be thrown from chute or jam in the auger.

•Always be aware of the direction the snow is being thrown. Nearby

pedestrians, pets or property may be harmed by objects being thrown.

•Familiarize yourself with the area you plan to work. Mark off boundaries of

walkways and driveways to prevent property damage from thrown objects.

•Take caution when snow throwing in unfamiliar areas. Stay alert for hidden

hazards and traffic.

•After striking a foreign object, turn engine OFF, wait for moving parts to

cease movement, and check immediately for damage. If damaged, repair

before starting and operating snow thrower.

•With engine OFF, wait for moving parts to stop and always use a stick to

clear discharge chute.

•If unit vibrates abnormally, turn engine OFF. Vibration is generally a

warning of trouble. See an authorized dealer if necessary for repairs.

DANGER

Rotating gears can contact or entangle hands, feet, hair,

clothing, or accessories.

Traumatic amputation or severe laceration can result.

•Always operate equipment with all guards in place.

•Keep hands and feet away from rotating gears.

•Tie up long hair and remove jewelry.

•Do not wear loose-fitting clothing, dangling drawstrings or items that could

become caught.

WARNING

Engines give off carbon monoxide, an odorless, colorless,

poison gas.

Breathing carbon monoxide can cause nausea, fainting or

death.

•Start and run engine outdoors.

•Do not start or run engine in enclosed area, even if doors or

windows are open.

WARNING

•Allow muffler, engine cylinder and fins to cool before touching.

•Remove accumulated combustibles from muffler area and cylinder

area.

•Install and maintain in working order a spark arrester before using

equipment on forest-covered, grass-covered, brush-covered

unimproved land. The state of California requires this (Section 4442 of

the California Public Resources Code). Other states may have similar

laws. Federal laws apply on federal land.

WARNING

Running engines produce heat. Engine parts, especially muffler,

become extremely hot.

Severe thermal burns can occur on contact.

Combustible debris, such as leaves, grass, brush, etc. can catch

fire.

Gasoline and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

WHEN ADDING FUEL

•Turn engine OFF and let engine cool at least 2 minutes before removing

gas cap.

•Fill fuel tank outdoors or in well-ventilated area.

•Do not overfill fuel tank.

•Keep gasoline away from sparks, open flames, pilot lights, heat, and other

ignition sources.

•Check fuel lines, tank, cap, and fittings frequently for cracks or leaks.

Replace if necessary.

WHEN STARTING ENGINE

•Make sure spark plug, muffler, fuel cap and air cleaner are in place.

•Do not crank engine with spark plug removed.

•If fuel spills, wait until it evaporates before starting engine.

•If engine floods, set choke to OPEN/RUN position, place throttle in FAST

and crank until engine starts.

WHEN OPERATING EQUIPMENT

•Do not choke carburetor to stop engine.

WHEN TRANSPORTING EQUIPMENT

•Transport with fuel tank EMPTY.

WHEN STORING GASOLINE OR EQUIPMENT WITH FUEL IN TANK

•Store away from furnaces, stoves, water heaters or other appliances that

have pilot light or other ignition source because they can ignite gasoline

vapors.

WARNING

Starting engine creates sparking.

Sparking can ignite nearby flammable gases.

Explosion and fire could result.

•If there is natural or LP gas leakage in area, do not start engine.

•Do not use pressurized starting fluids because vapors are flammable.

WARNING

Unintentional sparking can result in fire or electric shock.

Unintentional start-up can result in entanglement, traumatic

amputation, or laceration.

BEFORE PERFORMING ADJUSTMENTS OR REPAIRS

•Disconnect spark plug wire and keep it away from spark plug.

WHEN TESTING FOR SPARK

•Use approved spark plug tester.

•Do not check for spark with spark plug removed.

WARNING

Not for

Reproduction

IMPORTANT: Safety standards require operator presence control to

minimize the risk of injury. Your snowthrower is equipped with such

controls. Do not attempt to defeat the function of the operator presence

control under any circumstances.

Training

1. Read, understand, and follow all instructions on the machine and in

the manuals before operating this unit. Be thoroughly familiar with

the controls and the proper use of the equipment. Know how to stop

the unit and disengage the controls quickly.

2. Never allow children to operate the equipment. Never allow adults to

operate the equipment without proper instruction.

3. Keep the area of operation clear of all persons, particularly small

children, and pets.

4. Exercise caution to avoid slipping or falling especially when operating

in reverse.

Preparation

1. Thoroughly inspect the area where the equipment is to be used and

remove all doormats, sleds, boards, wires, and other foreign objects.

2. Disengage all clutches and shift into neutral before starting the

engine (motor).

3. Do not operate the equipment without wearing adequate winter outer

garments. Wear footwear that will improve footing on slippery

surfaces. Avoid loose fitting clothing that can get caught in moving

parts.

4. Handle fuel with care; it is highly flammable.

a. Use an approved fuel container.

b. Never add fuel to a running engine or hot engine.

c. Fill fuel tank outdoors with extreme care. Never fill fuel tank

indoors. Replace fuel cap securely and wipe up spilled fuel.

d. Never fill containers inside a vehicle or on a truck or trailer bed

with a plastic liner. Always place containers on the ground, away

from your vehicle, before filling.

ro kcurt eht morf tnempiuqe derewop- sag evomer ,lacitcarp nehW.e

trailer and refuel it on the ground. If this is not possible, then refuel

such on a trailer with a portable container, rather than from a

gasoline dispenser nozzle.

f. Keep nozzle in contact with the rim of the fuel tank or container

opening at all times, until refueling is complete. Do not use a

nozzle lock-open device.

g. Replace gasoline cap securely and wipe up spilled fuel.

h. If fuel is spilled on clothing, change clothing immediately.

5. Use extension cords and receptacles as specified by the

manufacturer for all units with electric drive motors or electric

starting motors.

6. Adjust the collector housing height to clear gravel or crushed rock

surfaces.

7. Never attempt to make any adjustments while the engine (motor) is

running (except when specifically recommended by manufacturer).

8. Let engine (motor) and snowthrower adjust to outdoor temperatures

before starting to clear snow.

9. Always wear safety glasses or eye shields during operation or while

performing an adjustment or repair to protect eyes from foreign

objects that may be thrown from the machine.

Operation

1. Do not put hands or feet near or under rotating parts. Keep clear of

the discharge opening at all times.

2. Exercise extreme caution when operating on or crossing gravel

drives, walks or roads. Stay alert for hidden hazards or traffic.

3. After striking a foreign object, stop the engine (motor), remove the

wire from the spark plug, disconnect the cord on electric motors,

thoroughly inspect snowthrower for any damage, and repair the

damage before restarting and operating the snowthrower.

4. If the unit should start to vibrate abnormally, stop the engine (motor)

and check immediately for the cause. Vibration is generally a warning

of trouble.

5. Stop the engine (motor) whenever you leave the operating position,

before unclogging the collector/impeller housing or discharge chute

and when making any repairs, adjustments, or inspections.

6. When cleaning, repairing, or inspecting, make certain the collector/

impeller and all moving parts have stopped. Disconnect the spark

plug wire and keep the wire away from the spark plug to prevent

accidental starting.

7. Do not run the engine indoors, except when starting the engine and

for transporting the snowthrower in or out of the building. Open the

outside doors; exhaust fumes are dangerous (containing CARBON

MONOXIDE, an ODORLESS and DEADLY GAS).

8. Exercise extreme caution when operating on slopes. Do not attempt

to clear steep slopes.

9. Never operate the snowthrower without proper guards, plates, or

other safety protective devices in place and working.

10. Never direct the discharge toward people or areas where property

damage can occur. Keep children and others away.

11. Do not overload the machine capacity by attempting to clear snow at

too fast a rate.

12. Never operate the machine at high transport speeds on slippery

surfaces. Look behind and use care when operating in reverse.

13. Disengage power to the collector/impeller when snowthrower is

transported or not in use.

14. Use only attachments and accessories approved by the manufacturer

of the snowthrower (such as cabs, tire chains, etc.).

15. Never operate the snowthrower without good visibility or light.

Always be sure of your footing and keep a firm hold on the handles.

Walk, never run.

16. Never touch a hot engine or muffler.

RULES FOR SAFE OPERATION

5

WARNING: This machine is capable of amputating hands and feet and throwing objects. Read these safety rules and follow them closely.

Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property

or equipment. The triangle in text signifies important cautions or warnings which must be followed.

Safe Operation Practices for Snowthrowers

As Recommended By: American National Standards Institute (ANSI)

Not for

Reproduction

17. Never operate the snowthrower near glass enclosures, automobiles,

window wells, drop-offs, and the like without proper adjustment of

the snow discharge angle.

18. Never direct discharge at bystanders or allow anyone in front of the

unit.

19. Never leave a running unit unattended. Always disengage the auger

and traction controls, stop engine, and remove keys.

20. Do not operate the unit while under the influence of alcohol or drugs.

21. Keep in mind the operator is responsible for accidents occurring to

other people or property.

22. Data indicates that operators, age 60 years and above, are involved

in a large percentage of power equipment-related injuries. These

operators should evaluate their ability to operate the unit safely

enough to protect themselves and others from injury.

23. DO NOT wear long scarves or loose clothing that could become

entangled in moving parts.

24. Snow can hide obstacles. Make sure to remove all obstacles from the

area to be cleared.

Children

Tragic accidents can occur if the operator is not alert to the presence of

children. Children are often attracted to the unit and the operating activity.

Never assume that children will remain where you last saw them.

1. Keep children out of the area and under the watchful care of another

responsible adult.

2. Be alert and turn off if children enter the area.

3. Never allow children to operate the unit.

4. Use extra care when approaching blind corners, shrubs, trees, or

other objects that may obscure vision.

Clearing A Clogged Discharge Chute

Hand contact with the rotating impeller inside the discharge chute is the

most common cause of injury associated with snowthrowers. Never use

your hand to clean out the discharge chute.

To clear the chute:

1. SHUT OFF THE ENGINE.

2. Wait 10 seconds to be sure the impeller blades have stopped

rotating.

3. Always use a clean-out tool, not your hands.

Service, Maintenance And Storage

1. Check shear bolts and other bolts at frequent intervals for proper

tightness to be sure the equipment is in safe working condition.

2. Never store the machine with fuel in the tank inside a building where

ignition sources are present such as hot water and space heaters, or

clothes dryers. Allow the engine to cool before storing in any

enclosure.

3. Always refer to operator’s manual for important details if the

snowthrower is to be stored for an extended period.

4. Maintain or replace safety and instruction labels as necessary.

5. Run the machine a few minutes after throwing snow to prevent

freeze-up of the collector/impeller.

6. If fuel is spilled, do not attempt to start the engine but move the

machine away from the area of spillage and avoid creating any source

of ignition until fuel vapors have dissipated.

7. Always observe safe refueling and fuel handling practices when

refueling the unit after transportation or storage.

8. Always follow the engine manual instructions for storage

preparations before storing the unit for both short and long term

periods.

9. Always follow the engine manual instructions for proper start-up

procedures when returning the unit to service.

10. Maintain or replace safety and instruction labels as necessary.

11. Keep nuts and bolts tight and keep equipment in good condition.

12. Never tamper with safety devices. Check their proper operation

regularly and make necessary repairs if they are not functioning

properly.

13. Components are subject to wear, damage, and deterioration.

Frequently check components and replace with manufacturer’s

recommended parts, when necessary.

14. Check control operation frequently. Adjust and service as required.

15. Use only factory authorized replacement parts when making repairs.

16. Always comply with factory specifications on all settings and

adjustments.

17. Only authorized service locations should be utilized for major service

and repair requirements.

18. Never attempt to make major repairs on this unit unless you have

been properly trained. Improper service procedures can result in

hazardous operation, equipment damage and voiding of

manufacturer’s warranty.

19. Check shear bolts (pins) and other bolts at frequent intervals for

proper tightness to be sure the equipment is in safe working

condition.

Emissions

1. Engine exhaust from this product contains chemicals known, in

certain quantities, to cause cancer, birth defects, or reproductive

harm.

2. If available, look for the relevant Emissions Durability Period and Air

Index information on the engine emissions label.

Ignition System

1. This spark ignition system complies with Canadian standard

ICES-002.

RULES FOR SAFE OPERATION

6

Not for

Reproduction

OWNER’S INFORMATION

7

MAINTENANCE AGREEMENT

The Craftsman Warranty, plus a Maintenance

Agreement, provide maximum value for Sears

products. Contact your nearest Sears store for de-

tails.

Gross Torque 13.5 T.P.

Gasoline Capacity 3 quarts (2.8 litre)

Oil Capacity (5W30) 28 oz (0.82 litre)

Spark Plug (Gap .030 in.) Champion RC12YC

CUSTOMER RESPONSIBILITIES

Read and observe the safety rules.

Follow a regular schedule in maintaining, caring for and

using your snow blower.

Follow the instructions under CUSTOMER RESPONSIBIL-

ITIES and STORAGE sections of this owner’s manual.

* See side of the tire for maximum inflation. Do not exceed the

maximum pressure on the tire wall.

*Tire Pressure

DATE PURCHASED:

MODEL NO:

SERIAL NO:

STORE WHERE PURCHASED:

ADDRESS:

CITY: PROVINCE:

TELEPHONE:

Record this information about your unit so that you will

be able to provide it in case of loss or theft. Armature Air Gap 0.010--0.014 in.

(0.25--0.36 mm)

)mm97(n.i021.3eroB

)mm26(n. i834.2ekortS

Displacement 305 cc

WHEELED SNOWTHROWER

LIMITED TWO (2) YEAR WARRANTY ON CRAFTSMAN SNOWTHROWER

For two (2) years from date of purchase, Sears Canada Inc. will repair or replace free of charge, at Sears option, parts

which are defective as a result of material or workmanship.

COMMERCIAL OR RENTAL USE:

Warranty on snowthrower will be 90 days from date of purchase if used for commercial or rental purposes.

THIS WARRANTY DOES NOT COVER:

1. Pre--delivery set--up.

2. Expendable items which become worn during normal use, such as belts, spark plugs, filter, shear pins as well as dam-

ages to the engine resulting from operating the snowthrower with insufficient oil.

3. Tire replacement or repair caused by punctures from outside objects, such as nails, thorns, stumps or glass.

4. In home service.

Warranty service is available by returning the Craftsman snowthrower to the nearest Sears Service Centre/Department

in Canada. This warranty applies only while this product is in use in Canada.

This warranty is in addition to any statutory warranty and does NOT exclude or limit legal rights you may have but shall

run concurrently with applicable provincial legislation. Furthermore, some provinces do not allow limitations on how long

an implied warranty will last so the above limitations may not apply to you.

SEARS CANADA INC., TORONTO, ONTARIO M5B 2B8

Not for

Reproduction

TABLE OF CONTENTS

8

HAZARD SYMBOLS AND THE MEANINGS 2..........

OPERATING SYMBOLS AND THEIR MEANINGS 3....

7NOITAMROFNIS’RE.N.W.......................O

9YLBMESSA ......................................

TOOLS REQUIRED FOR ASSEMBLY 9.............

CONTENTS OF SHIPPING CARTON 9.............

9G CONTENTS . . . . . . . . . . . . . . . . . . . . . . ABSTRAP

10GNIKCAPNU ...................................

UPPER HANDLE AND CRANK ASSEMBLY 11........

11SELBACEHTKCEHC ...........................

HOW TO SET THE LENGTH OF THE CABLE 11.....

R ASSEMBLY . . . . . . . . . . . . 11

EVEL

TCELESDEEPS

31YLBMESSAETUHCW.O.N...................S

41NOITAREPO ....................................

41SLORTNOCGNITAR.E.P....................O

SNOWTHROWER OPERATION . . . . . . . . . . . . . . . . 16

71

NIPTUOKCOLLE.E.H......................W

81ENIGNEGNITRATSERO.F.E.................B

81LIOEHTKCEHC ..............................

81SAGLLIF .....................................

BEFORE STOPPING THE ENGINE 19..............

91

ENIGNEPOTSOT.............................

91ENIGNETRATSOT ............................

12RETRATSNEZORF ............................

HOW TO CLEAR A CLOGGED

DISCHARGE CHUTE . . . . . . . . . . . . . . . . . . . . . . . . .

HOW TO USE THE CLEAN-OUT TOOL 21..........

22SPITGNITAREPO .............................

SERVICE RECOMMENDATIONS 23..................

CUSTOMER RESPONSIBILITIES 24..................

SNOWTHROWER . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

42EGAROTSTANOITACIR.B.U.................L

LUBRICATION -- EVERY 10 HOURS 24.............

LUBRICATION -- EVERY 25 HOURS 25.............

62ENIGNE ......................................

72RIAPER/TNEMTSU.J ..D........................A

AUGER HOUSING HEIGHT ADJUSTMENT 27.......

72RABREPARCSTSUJD.A.O..................T

72THGIEHDIKSTSUJD.A.O...................T

HOW TO REMOVE THE SNOW HOOD 28...........

92TNEMTSUJDATLEB ...........................

HOW TO REPLACE THE BELTS 30................

33TNEMTSUJDAEDIUGT.L.E..................B

HOW TO CHECK AND ADJUST THE CABLES 33...

AUGER DRIVE CABLE ADJUSTMENT 33...........

TRACTION DRIVE CABLE ADJUSTMENT 34........

HOW TO ADJUST OR REPLACE

53LEEHWNOITCIRF.E.H....................T

AUGER SHEAR BOLT REPLACEMENT 38..........

93EGAROTS ......................................

04TRAHCGNITOOHSELBUOR ....................T

34STRAPRIAPER .................................

24STRAPRIAPERREDRO ..........................

HEADLIGHT ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . 13

STARTING THE ENGINE . . . . . . . . . . . . . . . . . . . . . . . . 02

12

Not for

Reproduction

ASSEMBLY

9

TOOLS REQUIRED FOR ASSEMBLY

1 -- Knife

2 -- 1/2” wrenches (or adjustable wrenches)

2 -- 9/16” wrenches (or adjustable wrenches)

2 -- 3/4” wrenches (or adjustable wrenches)

1 -- 3/8” wrenches (or adjustable wrenches)

1 -- Pair pliers or screw driver (to spread cotter pin)

HOW TO MEASURE SCREW SIZE

LENGTH

DIAMETER

CONTENTS OF SHIPPING CARTON

1-- Snowthrower

1-- Container of Fuel Stabilizer (Located in Parts Bag)

1-- Snow Chute Assembly

1-- Crank Assembly

1-- Parts Bag

WARNING: Always wear safety glasses or eye

shields while assembling snowthrower.

PARTS BAG CONTENTS

*Non Assembly parts and power cord can be found in the Parts Bag shipped

with the snow thrower. The parts can be stored in the tool box located on top

of the belt cover.

1 -- Shifter Knob

(not actual size)

* 2 -- Wrenches

* 2--1/4--20 x 1.75 * 2--Spacer * 2--1/4--20

Hex nut

Not for

Reproduction

ASSEMBLY

10

Figure 1 shows the snowthrower in the shipping position.

Figure 2 shows the snowthrower completely assembled.

Reference to right and left hand side of the snowthrower is

from the operator’s position at the handle.

UNPACKING

1. Locate the two tear tabs at the bottom of the carton.

2. Pull the tear tape no more than twelve inches (30.48 cm)

at a time. Re--grasp tape next to the carton and pull

again. Repeat until all the tape is torn off.

3. After the tape has been completely removed from

the carton, remove the carton from the base. Cut all

four corners and fold the sides toward the center for

easy disposal.

4. Remove the plastic bag that covers the unit.

5. Locate and remove the parts bag.

NOTE: Set the fuel stabilizer aside until adding

gasoline to the fuel tank. We recommend that fuel

stabilizer is added to the fuel each time that gasoline

is added to the fuel tank.

6. For shipping purposes, the height adjust skids are at-

tached to the pallet. Remove the screw that secures

each height adjust skid to the pallet (see Figure 2).

7. Roll the snowthrower off the carton by pulling on the lower

handle.

CAUTION: DO NOT back over cables.

8. Remove the packing material from the handle assembly.

9. Cut ties securing the clutch control cables to the lower

handle.

NOTE: If the cables have become disconnected from the

clutch levers, reinstall the cables as shown in Figure 3.

Figure 1

Figure 3

”Z” Fitting Traction Drive Lever

Cable

Figure 2

Snow Chute

Deflector

Auger

Housing

Height Adjust

Skid

Toolbox

Crank

Traction Drive

Clutch Lever

Auger Drive

Clutch Lever

Headlight

Assembly

Speed

Selector

Lever

Not for

Reproduction

ASSEMBLY

11

UPPER HANDLE AND CRANK ASSEMBLY

1. Loosen, but do not remove the screws, flatwashers, lock-

washers and hex nuts in the upper holes of the lower

handle (see Figure 4).

2. Remove the fasteners and the crank assembly eyebolt

from the lower holes of the lower handle.

3. Raise upper handle into operating position. Upper han-

dle should be to the outside of the lower handle.

NOTE: Make sure the cables are not caught between

the upper and lower handle.

4. Install the fasteners and the crank assembly eyebolt that

were removed in step 2. DO NOT tighten until all fasten-

ers are in place.

5. Attach the crank rod to the universal joint assembly with

the hair pin (see Figure 5).

6. Tighten nut on eye bolt. Make sure eye bolt is properly

aligned and the crank can freely rotate (see Figure 4).

7. Tighten all handle bolts.

NOTE: Make sure crank does not touch carburetor

cover.

Figure 4

Crank

Eye Bolt

Adaptor Boot

Flatwasher

Nut

Flatwasher

Bolt

Lockwasher

Flatwasher

Locknut

Figure 5

Crank Rod

Assembly

Universal Joint

Hair Pin

CHECK THE CABLES

1. If control cables have become unattached from motor

mount frame, reconnect cables as shown in Figure 6.

2. For cable adjustments, see “How To Check And Adjust

The Cables” in the ADJUSTMENT/REPAIR section.

HOW TO SET

THE LENGTH OF THE CABLES

The cables were adjusted at the factory and no adjustments

should be necessary. However, after the handles are put in

the operating position, the cables can be too tight or too

loose. If an adjustment is necessary, see “How To Check And

Adjust The Cables” in the ADJUSTMENT/REPAIR section.

Traction Drive Cable Auger Drive Cable

Figure 6

Not for

Reproduction

ASSEMBLY

12

SPEED SELECT LEVER ASSEMBLY

1. Cut plastic tie securing speed select lever assembly to

the shifter bracket (see Figure 7).

2. Remove locknut, washer, spring, and the bolt (see

Figure 9).

3. Position speed selector lever assembly as shown in

Figure 8.

4. Reinstall bolt, spring, washer and locknut (see Figure 9).

5. Tighten locknut until 1/8 to 3/16 inch of the bolt threads

protrude past the locknut.

6. Thread the 3/8--16” hex jam nut onto the lever until the

nut reaches the end of the thread (see Figure 9).

7. Thread the plastic knob as far as possible and ensure

that the knob points forward.

8. Tighten the 3/8--16” hex jam nut against the knob

securely.

9. Move shifter through all speeds to ensure proper tension

of the spring. If shifter lever sticks in any of the notches,

loosen locknut 1/2 turn at a time until shifter lever moves

more freely.

Figure 7

Plastic Tie

Shift Lever

Shifter Bracket

Figure 8

Control Panel

Shifter Bracket

Figure 9

Control Panel

Shifter Bracket

3/8--16 Hex Jam Nut

1/8 to 3/8 inch of

Exposed Thread

Plastic Knob

(pointed

forward)

Bolt

Spring

Locknut

NOTE: View is from right side of unit standing in operator’s position.

Not for

Reproduction

ASSEMBLY

13

SNOW CHUTE ASSEMBLY

CHECK THE TIRES

The tires were over inflated for shipment. Check the tire

pressure in the tires. See the sidewall of the tire for the

proper inflation.

IMPORTANT! BEFORE YOU START

OPERATING

Check the fasteners. Make sure all fasteners are

tight.

On electric start models, the unit was shipped with

the starter cord plugged into the engine. Before

operating, unplug the starter cord from the engine.

NOTE: This snowthrower was shipped WITH OIL in the engine. See “Before Starting Engine” in-

structions in the OPERATION section of this manual before starting engine.

HEADLIGHT ASSEMBLY

The headlight is mounted on the right side of the upper

handle. It is installed upside--down for shipping purposes.

1. Remove the nut and lockwasher from the carriage bolt.

2. Turn the headlight to the top side of the upper handle.

Ensure external tooth lock washer and saddle washer

are in place as shown in Figure 11.

3. Install the nut and lockwasher to secure the headlight

to the handle. The headlight should point toward the

snow clearing path.

Figure 11

Carriage

Bolt

Lockwasher

Saddle

Washer

External

Tooth

Lockwasher

Cable Tie

Hex Nut

1. Turn crank assembly (Figure 2) until the arrow

on outer ring (2, Figure 10) of chute ring as-

sembly points forward.

NOTE: The chute ring assembly (1) comes installed

on the unit from the factory (see Figure 10).

NOTE: Make sure the slot in the chute ring aligns

with the arrow on the outer ring.

2. Install chute deflector (3) using four screws

(4) and nuts (5) in holes as shown. The chute

deflector must point forward for proper

installation.

3. Tighten screws snugly but be careful not to

over-tighten.

2

1

3

4

5

Figure 10

Not for

Reproduction

14

OPERATION

Get to know your snowthrower and its controls. Be sure you (or any other operator) have read and understood the Operation

Precautions listed on page 2 of this manual.

Figure 12

Clean-out Tool

ENGINE AND SNOWTHROWER OPERATING CONTROLS

The engine operating controls and their functions are as

follows:

Choke Control-- Set choke control to ON CHOKE position

to start a cold engine.

Electric Start Button-- Used to start the engine using the

electric starter.

Prime Button-- Used to inject fuel directly into carburetor

manifold to insure fast starts in cool weather.

Safety Key-- Must be inserted into ignition key slot to start

engine. Pull out to stop. Do not turn safety key.

Starter Handle-- Starts the engine manually.

Toolbox

Speed

Select

Lever

Headlight

Assembly

Auger Drive

Clutch Lever Traction Drive

Clutch Lever

Snow Chute

Deflector

Safety

Key

Primer Button

Choke

Control

Recoil Starter

Handle

Crank

Gas Tank

Gas Cap

Height Adjust

Skid

Auger

Housing

Not for

Reproduction

OPERATION

15

The snow blower operating controls and their functions

are as follows:

Speed Select Lever-- Allows the operator to use one of six

(6) forward and two (2) reverse speeds. To shift, move speed

select lever to desired position.

NOTE: Do not move speed select lever while Traction

Drive Clutch is engaged. This may result in severe

damage to drive system.

Auger Drive Clutch Lever-- Used to engage and disengage

the auger and impeller. To engage push down, to disengage

release.

Traction Drive Clutch Lever-- Used to propel snowthrower

forward or reverse. Push down to engage, release to

disengage.

Snow Chute Deflector-- Changes the direction the snow is

blown.

Height Adjust Skid-- Used to adjust ground clearance of

auger housing (see "To Adjust Skid Height" in the

ADJUSTMENT/REPAIR section of this manual).

Toolbox -- Spare shear pins, shear bolt wrenches and

spacers are located in toolbox.

Clean-Out Tool -- Use the clean-out tool toremove snow and

debirs from the discharge chute and the auger housing.

Crank (Not Shown) - Used to change direction of the

snow discharge. turn handle clockwise to turn chute to

right. Turn handle counterclockwise to turn chute to left.

Not for

Reproduction

OPERATION

16

The operation of any snowthrower can result in foreign objects being thrown into the eyes,which can

result in severe eye damage. Always wear safety glasses or eye shields before beginning snowthrower

Operation. We recommend standard safety glasses or Wide Vision Safety Mask for over spectacles.

SNOWTHROWER OPERATION

The most effective use of the snowthrower will be established

by experience, taking into consideration the terrain, wind

conditions and building location which will determine the

direction of the discharge chute.

NOTE: Do not blow snow towards a building as hidden

objects could be blown with sufficient force to cause

damage.

1. Start the engine as described in section “To Start Engine”

(see Figure 14).

2. Adjust snow chute deflector. Loosen wing nut on the side

of the snow chute and raise chute deflector for more dis-

tance. Tighten wing nut (see Figure 13).

3. Using crank, position the discharge chute to discharge

snow with the wind.

4. Select proper speed for snow conditions as outlined be-

low and set speed select lever to desired position.

NOTE: Always release traction drive clutch lever

before moving speed select lever.

Ground speed is determined by snow conditions. Select

the speed you desire by moving the speed selector into

the appropriate colored area on the control panel.

1--2 Wet, Heavy, Slushy, Extra Deep

3Moderate

4--5 Very Light

6Transport Only

NOTE: When clearing wet, heavy snow,itis

recommended that the ground speed of the unit be

reduced and do not attempt to clear the full width of

the unit.

For additional operating instructions see “Operating

Tips” in this section of the manual.

5. Engage auger drive clutch lever (right hand--Figure 14).

IMPORTANT: Be sure front of unit is clear of

bystanders or obstacles before operating.

6. Engage traction drive clutch lever (left hand--Figure 14).

As the snowthrower starts to move, maintain a firm hold

on the handles and guide the snowthrower along the cut-

ting path. Do not attempt to push the snowthrower.

WARNING: Read Owner’s Manual before oper-

ating machine. This machine can be dangerous

if used carelessly.

Never operate the snowthrower without all guards, cov-

ers, and shields in place.

Never direct discharge towards windows or allow by-

standers near machine while engine is running.

Stop the engine whenever leaving the operating posi-

tion.

Disconnect spark plug before unclogging the impeller

housing or the discharge chute and before making re-

pairs or adjustments.

When leaving the machine, remove the safety key.

To reduce the risk of fire, keep the machine clean and

free from spilled gas, oil and debris.

Figure 13

Figure 14

Auger Drive

Clutch Lever

Traction Drive

Clutch Lever Disengaged

Disengaged

degagnEdegagnE

7. To stop forward motion, release traction drive clutch lever

(left hand -- Figure 14).

8. To stop auger, release auger drive clutch lever (right

hand -- Figure 14).

9. To move the snowthrower backwards, move speed select

lever into first or second reverse and engage traction

drive clutch lever (left hand). To stop, release traction

drive clutch lever.

Wing Nut

Not for

Reproduction

OPERATION

17

WHEEL LOCK OUT PIN

1. The right wheel is secured to the axle with aklick pin. This

unit was shipped with this klick pin in the locked position.

(see Figure 15).

2. For ease of maneuverability when lighter conditions

prevail, remove klick pin from wheel locked position and

insert into the single wheel drive (unlocked) position.

(see Figure 16). Make sure that the klick pin is in the

single wheel drive position of the axle only and not

through the locked position.

NOTE: Check tire pressure. See side of tire for maximum

inflation. Do not exceed listed maximum pressure.

Figure 15

Locked

Position

Klik Pin

Figure 16

Single Wheel

Drive Position

(Unlocked) Klik Pin

Not for

Reproduction

BEFORE STARTING ENGINE

CHECK THE ENGINE

NOTE: The engine was shipped from the factory filled with oil.

Check the level of the oil. Add oil as needed.

1. Make sure the unit is level. Use a high quality detergent oil

classified “For Service SG, SH, SJ, SL, or higher”.

2. Remove the oil fill cap/dipstick and wipe with a clean cloth

(see Figure 17).

3. Insert the oil fill cap/dipstick and turn clockwise to tighten.

4. Remove the oil fill cap/dipstick and check the oil.

NOTE: Do not check the level of the oil while the engine

runs.

5. If necessary, add oil until the oil reaches the FULL mark on the

oil fill cap/dipstick (see Figure 17). Do not add too much oil.

6. Tighten the fill cap/dipstick securely each time you check the

oil level.

NOTE: For extreme cold operating conditions of 0°F (-18°C) and

below, use a synthetic 5W30 motor oil for easier starting.

NOTE: S.A.E. 5W30 motor oil may be used to make starting eas-

ier in areas where the temperature is 20°F (-7°C) to 0°F (-18°C).

Synthetic 5W30 is acceptable for all temperatures. DO NOT mix

oil with gasoline.

NOTE: SEE CHART FOR OIL RECOMMENDATION.

FILL GAS

This engine is certified to operate on gasoline. Exhaust Emission

Control System: EM (Engine Modifications).

1. Fill the fuel tank with fresh, clean, unleaded regular, unleaded

premium, or reformulated automotive gasoline with a mini-

mum of 85 octane along with a fuel stabilizer (follow instruc-

tions on fuel stabilizer package). DO NOT use leaded gasoline.

We recommend that fuel stabilizer be added to the fuel each

time that gasoline is added to the fuel tank.

NOTE: Winter grade gasoline has higher volatility to

improve starting. Be certain container is clean and free

from rust or other foreign particles. Never use gasoline that

may be stale from long periods of storage in the container.

WARNING: Gasoline is flammable. Always use caution

when handling or storing gasoline. Turn engine off and let

engine cool at least two minutes before removing the gas cap.

Do not add gasoline to the fuel tank while snowthrower is

running, hot, or when snowthrower is in an enclosed area. Keep

away from open flame, electrical sparks and DO NOT SMOKE

while filling the fuel tank. Never fill the fuel tank completely; but

fill the fuel tank to within 1-1/2 inches (3.8 mm) from the top to

provide space for the expansion of the fuel. Always fill fuel tank

outdoors and use a funnel or spout to prevent spilling. Make

sure to wipe up any spilled fuel before starting the engine.

Store gasoline in a clean, approved container, and keep the cap

in place on the container. Keep gasoline in a cool well ventilated

place; never in the house. Never buy more than a 30 day supply

of gasoline to assure volatility. Gasoline is intended to be used

as a fuel for internal combustion engines; therefore, do not use

gasoline for any other purpose. Since many children like the

smell of gasoline, keep it out of their reach because the fumes

are dangerous to inhale, as well as being explosive.

F− 20

C −30 −20 −10 0 10

0203240

Synthetic 5W30

5W30

SAE VISCOSITY GRADES

TEMPERATURE TYPE OF OIL

0°F (-18°C) and above S.A.E. 5W30

0°F (-18°C) and below synthetic 5W30

OPERATION

18

FULL

Figure 17

Oil Fill Cap/Dipstick

Fuel Tank

Not for

Reproduction

OPERATION

19

BEFORE STOPPING THE ENGINE

Run the engine for a few minutes to help dry off any moisture

on the engine.

TO STOP ENGINE

TO START ENGINE

Be sure that engine oil is at FULL mark on the oil fill

cap/dipstick. The snow thrower engine is equipped with

A.C. electric starter and recoil starter. Before starting the

engine, be certain that you have read the following

information.

If engine floods, set the choke to the OPEN/RUN position and

crank until the engine starts.

WARNING: The electric starter is equipped with

a three−wire power cord and plug designed to

operate on AC house hold current. The

power cord must be properly grounded at all times to

avoid the possibility of electric shock which can cause

injury to the operator. Follow all instructions carefully

as set forth below:

Make sure your house has a three−wire grounded sys-

tem. If you are not sure, ask a licensed electrician. If

your house does not have a three−wire grounded sys-

tem, do not use this electric starter under any condi-

tion.

If your house has a three−wire grounded system but a

three hole receptacle is not available to connect the

electric starter, have a three−hole receptacle installed

by a licensed electrician.

WARNING: To connect power cord, always

connect the power cord first to the

switch box located on the engine and then plug

the other end into a three−hole grounded receptacle.

WARNING: To disconnect the power cord, al-

ways unplug the end connected to the three−

hole grounded receptacle first.

WARNING

Gasoline and its vapors are extremely

flammable and explosive.

Fire or explosion can cause severe burns or

death.

DO NOT choke the carburetor to stop the

engine.

1. Move the stop switch (A, Figure 18) to the stop

position.

2. Remove the safety key (B). Keep the safety key

out of reach of children.

A

B

Figure 18. Stopping the Engine

A. On/Stop Switch

B. Safety Key

NOTE: Do not lose the safety/ignition key. Keep the

safety/ignition key is a safe place. The engine will not

start without the safety/ignition key.

Not for

Reproduction

OPERATION

20

STARTING THE ENGINE

1. Check the oil level. See the Engine Manual

How

to Check/Add Oil

section

2. Make sure equipment drive controls are

disengaged.

3. Push the stop switch to the on position (A, Figure

19).

A

Figure 19. On/Stop Switch

A. On/Stop Switch Selector

4. Insert the engine key (A, Figure 20) into the engine

key slot and push fully in to the RUN position.

5. Turn the choke knob (B) fully clockwise if engine is

cold.

Note: Do not use the choke to start a warm engine.

6. Push the primer button (C) two times.

Note: Do not use the primer to start a warm engine.

Note: If the engine does not start after three attempts,

see the Engine Manual Troubleshooting section.

8. Electric Start: First connect the extension cord to

the power cord receptacle and then into a wall

receptacle. If additional extension cord is

required, make sure it is 3-wire.

Figure 21. Rewind Start

A. Starter Cord Handle

A

WARNING

Rapid retraction of the starter cord (kickback)

will pull your hand and arm toward the engine

faster than you can let go. Broken bones,

fractures, bruises or sprains could result.

When starting engine, pull the starter cord

slowly until resistance is felt and then pull

rapidly to avoid kickback.

C

A

B

7. Rewind Start: Firmly hold the starter cord handle

(A, Figure 21). Pull the starter cord handle slowly

until resistance is felt, then pull rapidly.

CAUTION

To extend the life of the starter, use short

starting cycles (five seconds maximum.) Wait

one minute between starting cycles.

A

B

Figure 22. Electric Start

A. Starter Push Button

B. Power Cord Receptacle

Note: If the engine does not start after three attempts,

see the Engine Manual Troubleshooting section.

WARNING

If the extension cord is damaged, it must be

replaced by the manufacturer or its service

agent or a similarly qualified person to avoid to

avoid a hazard.

9. Electric Start: Depress the push button (A, Figure

22). After you start the engine, first disconnect the

extension cord from the wall receptacle and then

from the power cord receptacle (B).

Figure 20. Electric Start

A. Engine Key

B. Choke Knob

C. Primer Button

Not for

Reproduction

La page est en cours de chargement...

Simplicity SEARS CRAFTSMAN SNOWTHROWER Manuel utilisateur

Simplicity SEARS CRAFTSMAN SNOWTHROWER Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents