Simplicity 6271200X43 Manuel utilisateur

1741062 TP 199-4725-00-ST-Y

Read and keep this book for future reference. This book contains important information on SAFETY,

ASSEMBLY, OPERATION, AND MAINTENANCE.

Lisez et conservez ce manuel pour référence. Ce manuel contient des informations importantes

concernant la

SECURITE, LE MONTAGE, L’UTILISATION ET L’ENTRETIEN.

Instruction Book Snow Thrower Model 6271200X43

Manuel d’instructions chasse−neige modèle 6271200X43

2

1741062

NOTE: This unit is equipped with an internal combustion engine

and must not be used on or near any unimproved

forest−covered, brush−covered or grass−covered land unless

the engine’s exhaust system is equipped with a spark arrester

meeting applicable local or state laws (if any). If a spark arrester

is used, it must be maintained in effective working order by the

operator.

In the State of California, the above is required by law (Section

4442 of the California Public Resources Code). Other states

may have similar laws. Federal laws apply on federal lands. See

an Authorized Service Center for a spark arrester for the

muffler.

Engine Exhaust, some of its constituents, and

certain vehicle components contain or emit

chemicals known to the State of California to

cause cancer and birth defects or other repro-

ductive harm.

Battery posts, terminals and related accesso-

ries contain lead and lead compounds, chemi-

cals known to the State of California to cause

cancer and birth defects or other reproductive

harm. WASH HANDS AFTER HANDLING.

REMARQUE : cette machine est équipée d’un moteur à

combustion interne et ne doit pas être utilisée sur un terrain

forestier, buissonnant ou herbeux non préparé, à moins que le

dispositif d’échappement soit pourvu d’un pare−étincelles

conforme à la législation locale ou de l’état (le cas échéant). Si

un pare−étincelles est utilisé, celui−ci doit être maintenu en

parfait état de fonctionnement par l’utilisateur.

Au sein de l’état de Californie, la loi exige la prise en compte

des précautions mentionnées ci−dessus (clause 4442 du

California Public Resources Code). D’autres états peuvent

présenter des lois similaires. Les lois fédérales s’appliquent sur

les terres fédérales. S’adresser à un centre de maintenance

agréé pour l’achat d’un pare−étincelles pour l’échappement.

Les gaz d’échappement du moteur, certains

éléments de leur composition, ainsi que

certains organes du véhicule contiennent ou

émettent des substances chimiques qui, selon

l’État de Californie, peuvent causer le cancer,

des malformations à la naissance, ou

représentent un danger pour la reproduction.

Les bornes et pôles de batterie et autres

accessoires de ce type contiennent du plomb et

des composés de plomb, substances

chimiques qui, selon l’État de Californie,

peuvent causer le cancer, des malformations à

la naissance, ou représentent un danger pour la

reproduction.

RULES FOR SAFE OPERATION

3

1741062

General Information

This instruction book is written for a person with some mechanical ability.

Like most service books, not all the steps are described. Steps on how to

loosen or tighten fasteners are steps anyone can follow with some

mechanical ability. Read and follow these instructions before you use the

unit.

Know your product: If you understand the unit and how the unit

operates, you will get the best performance. As you read this manual,

compare the illustrations to the unit. Learn the location and the function of

the controls. To help prevent an accident, follow the operating instructions

and the safety rules. Keep this manual for future reference.

IMPORTANT: Many units are not assembled and are sold in cartons. It is

the responsibility of the owner to make sure the assembly instructions in

this manual are exactly followed. Other units are purchased in an

assembled condition. On assembled units, it is the responsibility of the

owner to make sure the unit is correctly assembled. The owner must

carefully check the unit according to the instructions in this manual before

it is first used.

This manual contains safety information to make you

aware of the hazards and risks associated with snow

throwers, and how to avoid them. The snow thrower is designed and

intended for removal of snow, and should not be used for any other

purpose. It is important that you read and understand these

instructions, and anyone operating the equipment read and

understand these instructions.

The engine exhaust from this product contains chemicals known to the

State of California to cause cancer, birth defects, or other reproductive

harm.

WARNING

A signal word (DANGER, WARNING, or CAUTION) is used with the alert

symbol to indicate the likelihood and the potential severity of injury. In

addition, a hazard symbol may be used to represent the type of hazard.

DANGER indicates a hazard which, if not avoided, will result in

death or serious injury.

WARNING indicates a hazard which, if not avoided, could result

in death or serious injury.

CAUTION indicates a hazard which, if not avoided, might result

in minor or moderate injury.

CAUTION, when used without the alert symbol, indicates a

situation that could result in damage to the equipment.

Hazard Symbols and the meanings

These symbols are used on your equipment and defined in your operating

manual. Review and understand the meanings. The use of one of these

symbols combined with a signal word will alert you to potential hazards

and how to avoid them.

Explosion

Toxic fumes

Shock

Hot Surface

Fire

Operator’s Manual − Read and understand

before performing any activity or running

equipment.

Safety Alert − Identifies safety information about

hazards that can result in personal injury.

Rotating auger

Rotating impeller

Rotating gears

Thrown objects

Keep a safe distance

from the equipment.

Shut off engine and

remove spark plug

connector before

performing maintenance

or repair work.

Never reach into

rotating parts.

Recommended ear

protection for

extended use.

RULES FOR SAFE OPERATION

4

1741062

Operating Symbols and their meanings

These symbols are used on your equipment and defined in your operating

manual. It is important that you review and understand the meanings.

Failure to understand the symbols might result in harm to you.

Stop

Fuel

Choke off

Oil

Choke on

Slow

Fast

On Off

Ignition Key

Ignition Off

Ignition On

Primer bulb

Throttle

Drive Clutch

Auger Clutch

Engage

RIGHT

Auger Collector

Traction

Discharge Chute

LEFT UP

DOWN

Forward

Neutral

Reverse

Push to engage

electric start

Electric

Start

Engine

Start

Engine Run

Engine Off

Chute Deflector

Engage

Disengage

Heated Grips

Avoid death or serious injury from rotating auger.

Keep hands, feet and clothing away.

Unclogging discharge chute is a hazardous activity.

• Stop engine and disconnect spark plug wire when performing maintenance

on equipment.

• Never leave the equipment unattended while engine is running. Always

disengage the auger and traction controls, stop engine, and remove keys.

• Keep children, pets, and others out of the area during operation. Children

are often attracted to the equipment. Be mindful of all persons present.

• Keep all loose clothing far away from front of snow thrower and auger.

Scarves, mittens, dangling drawstrings, loose clothes and pants can

quickly become caught in the rotating device and dismemberment will

occur. Tie up long hair and remove jewelry.

• The snow thrower is intended to remove snow only. Do not use for

purposes other than what is intended.

• Do not clear snow across the face of slopes. Exercise extreme caution when

changing direction on slopes. Do not attempt to clear steep slopes.

• Do not use the snow thrower on surfaces above ground level such as roofs

of residences, garages, porches or other such structures or buildings.

DANGER

Discharge chute contains rotating impeller to throw snow.

Never clear or unclog discharge chute with your hands, or

while engine is running.

Fingers can quickly become caught and traumatic

amputation or severe laceration can result.

• Unclogging the discharge chute is a hazardous activity. Clogged or

blocked augers store energy and can rotate unexpectedly.

• Never place hands in or near discharge chute.

• With engine OFF, wait for all moving parts to cease movement, then with a

stick, clear the chute. Even with engine off, parts may rotate and

dismemberment can occur.

• Clogged snow can hide other obstructions in the chute and cause damage

to the equipment, impeller or auger. Take precautions when restating the

equipment after snow removal.

DANGER

RULES FOR SAFE OPERATION

5

1741062

Objects can be picked up by auger and thrown from chute.

Never throw snow toward people or cars, and never allow

anyone in front of the snow thrower.

• Be aware of your environment while operating equipment. Running over

items such as, gravel, doormats, newspapers, toys, and rocks hidden

under snow, can all be thrown from chute or jam in the auger.

• Always be aware of the direction the snow is being thrown. Nearby

pedestrians, pets or property may be harmed by objects being thrown.

• Familiarize yourself with the area you plan to work. Mark off boundaries of

walkways and driveways to prevent property damage from thrown objects.

• Take caution when snow throwing in unfamiliar areas. Stay alert for hidden

hazards and traffic.

• After striking a foreign object, turn engine OFF, wait for moving parts to

cease movement, and check immediately for damage. If damaged, repair

before starting and operating snow thrower.

• With engine OFF, wait for moving parts to stop and always use a stick to

clear discharge chute.

• If unit vibrates abnormally, turn engine OFF. Vibration is generally a

warning of trouble. See an authorized dealer if necessary for repairs.

DANGER

Rotating gears can contact or entangle hands, feet, hair,

clothing, or accessories.

Traumatic amputation or severe laceration can result.

• Always operate equipment with all guards in place.

• Keep hands and feet away from rotating gears.

• Tie up long hair and remove jewelry.

• Do not wear loose-fitting clothing, dangling drawstrings or items that could

become caught.

WARNING

Engines give off carbon monoxide, an odorless, colorless,

poison gas.

Breathing carbon monoxide can cause nausea, fainting or

death.

• Start and run engine outdoors.

• Do not start or run engine in enclosed area, even if doors or

windows are open.

WARNING

• Allow muffler, engine cylinder and fins to cool before touching.

• Remove accumulated combustibles from muffler area and cylinder

area.

• Install and maintain in working order a spark arrester before using

equipment on forest-covered, grass-covered, brush-covered

unimproved land. The state of California requires this (Section 4442 of

the California Public Resources Code). Other states may have similar

laws. Federal laws apply on federal land.

WARNING

Running engines produce heat. Engine parts, especially muffler,

become extremely hot.

Severe thermal burns can occur on contact.

Combustible debris, such as leaves, grass, brush, etc. can catch

fire.

Gasoline and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

WHEN ADDING FUEL

• Turn engine OFF and let engine cool at least 2 minutes before removing

gas cap.

• Fill fuel tank outdoors or in well-ventilated area.

• Do not overfill fuel tank.

• Keep gasoline away from sparks, open flames, pilot lights, heat, and other

ignition sources.

• Check fuel lines, tank, cap, and fittings frequently for cracks or leaks.

Replace if necessary.

WHEN STARTING ENGINE

• Make sure spark plug, muffler, fuel cap and air cleaner are in place.

• Do not crank engine with spark plug removed.

• If fuel spills, wait until it evaporates before starting engine.

• If engine floods, set choke to OPEN/RUN position, place throttle in FAST

and crank until engine starts.

WHEN OPERATING EQUIPMENT

• Do not choke carburetor to stop engine.

WHEN TRANSPORTING EQUIPMENT

• Transport with fuel tank EMPTY.

WHEN STORING GASOLINE OR EQUIPMENT WITH FUEL IN TANK

• Store away from furnaces, stoves, water heaters or other appliances that

have pilot light or other ignition source because they can ignite gasoline

vapors.

WARNING

Starting engine creates sparking.

Sparking can ignite nearby flammable gases.

Explosion and fire could result.

• If there is natural or LP gas leakage in area, do not start engine.

• Do not use pressurized starting fluids because vapors are flammable.

WARNING

Unintentional sparking can result in fire or electric shock.

Unintentional start-up can result in entanglement, traumatic

amputation, or laceration.

BEFORE PERFORMING ADJUSTMENTS OR REPAIRS

• Disconnect spark plug wire and keep it away from spark plug.

WHEN TESTING FOR SPARK

• Use approved spark plug tester.

• Do not check for spark with spark plug removed.

WARNING

IMPORTANT: Safety standards require operator presence control to

minimize the risk of injury. Your snowthrower is equipped with such

controls. Do not attempt to defeat the function of the operator presence

control under any circumstances.

Training

1. Read, understand, and follow all instructions on the machine and in

the manuals before operating this unit. Be thoroughly familiar with

the controls and the proper use of the equipment. Know how to stop

the unit and disengage the controls quickly.

2. Never allow children to operate the equipment. Never allow adults to

operate the equipment without proper instruction.

3. Keep the area of operation clear of all persons, particularly small

children, and pets.

4. Exercise caution to avoid slipping or falling especially when operating

in reverse.

Preparation

1. Thoroughly inspect the area where the equipment is to be used and

remove all doormats, sleds, boards, wires, and other foreign objects.

2. Disengage all clutches and shift into neutral before starting the

engine (motor).

3. Do not operate the equipment without wearing adequate winter outer

garments. Wear footwear that will improve footing on slippery

surfaces. Avoid loose fitting clothing that can get caught in moving

parts.

4. Handle fuel with care; it is highly flammable.

a. Use an approved fuel container.

b. Never add fuel to a running engine or hot engine.

c. Fill fuel tank outdoors with extreme care. Never fill fuel tank

indoors. Replace fuel cap securely

and wipe up spilled fuel.

d. Never fill containers inside a vehicle or on a truck or trailer bed

with a plastic liner. Always place containers on the ground, away

from your vehicle, before filling.

ro kcurt eht morf tnempiuqe derewop- sag evomer ,lacitcarp nehW.e

trailer and refuel it on the ground. If this is not possible, then refuel

such on a trailer with a portable container, rather than from a

gasoline dispenser nozzle.

f. Keep nozzle in contact with the rim of the fuel tank or container

opening at all times, until refueling is complete. Do not use a

nozzle lock-open device.

g. Replace gasoline cap securely and wipe up spilled fuel.

h. If fuel is spilled on clothing, change clothing immediately.

5. Use extension cords and receptacles as specified by the

manufacturer for all units with electric drive motors or electric

starting motors.

6. Adjust the

collector housing height to clear gravel or crushed rock

surfaces.

7. Never attempt to make any adjustments while the engine (motor) is

running (except when specifically recommended by manufacturer).

8.

Let engine (motor) and snowthrower adjust to outdoor temperatures

before starting to clear snow.

9. Always wear safety glasses or eye shields during operation or while

performing an adjustment or repair to protect eyes from foreign

objects that may be thrown from the machine.

Operation

1. Do not put hands or feet near or under rotating parts. Keep clear of

the discharge opening at all times.

2. Exercise extreme caution when operating on or crossing gravel

drives, walks or roads. Stay alert for hidden hazards or traffic.

3. After striking a foreign object, stop the engine (motor), remove the

wire from the spark plug, disconnect the cord on electric motors,

thoroughly inspect snowthrower for any damage, and repair the

damage before restarting and operating the snowthrower.

4. If the unit should start to vibrate abnormally, stop the engine (motor)

and check immediately for the cause. Vibration is generally a warning

of trouble.

5. Stop the engine (motor) whenever you leave the operating position,

before unclogging the collector/impeller housing or discharge chute

and when making any repairs, adjustments, or inspections.

6. When cleaning, repairing, or inspecting, make certain the collector/

impeller and all moving parts have stopped. Disconnect the spark

plug wire and keep the wire

away from the spark plug to prevent

accidental starting.

7. Do not run the engine indoors, except when starting the engine and

for transporting the snowthrower in or out of the building. Open the

outside doors; exhaust fumes are dangerous (containing CARBON

MONOXIDE, an ODORLESS and DEADLY GAS).

8. Exercise extreme caution when operating on slopes. Do not attempt

to clear steep slopes.

9. Never operate the snowthrower without proper guards, plates, or

other safety protective devices in place and working.

10. Never direct the discharge toward people or areas where property

damage can occur. Keep children and others away.

11. Do not overload the machine capacity by attempting to clear snow at

too fast a rate.

12. Never operate the machine at high transport speeds on slippery

surfaces. Look behind and use care when operating in reverse.

13. Disengage power to the collector/impeller when snowthrower is

transported or not in use.

14. Use only attachments and accessories approved by the manufacturer

of the snowthrower (such as cabs, tire chains, etc.).

15. Never operate the snowthrower

without good visibility or light.

Always be sure of your footing and keep a firm hold on the handles.

Walk, never run.

16. Never touch a hot engine or

muffler.

RULES FOR SAFE OPERATION

6

WARNING: This machine is capable of amputating hands and feet and throwing objects. Read these safety rules and follow them closely.

Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property

or equipment. The triangle in text signifies important cautions or warnings which must be followed.

Safe Operation Practices for Snowthrowers

As Recommended By: American National Standards Institute (ANSI)

1741062

17. Never operate the snowthrower near glass enclosures, automobiles,

window wells, drop-offs, and the like without proper adjustment of

the snow discharge angle.

18. Never direct discharge at bystanders or allow anyone in front of the

unit.

19. Never leave a running unit unattended. Always disengage the auger

and traction controls, stop engine, and remove keys.

20. Do not operate the unit while under the influence of alcohol or drugs.

21. Keep in mind the operator is responsible for accidents occurring to

other people or property.

22. Data indicates that operators, age 60 years and above, are involved

in a large percentage of power equipment-related injuries. These

operators should evaluate their ability to operate the unit safely

enough to protect themselves and others from injury.

23. DO NOT wear long scarves or loose clothing that could become

entangled in moving parts.

24. Snow can hide obstacles. Make sure to remove all obstacles from the

area to be cleared.

Children

Tragic accidents can occur if the operator is not alert to the presence of

children. Children are often attracted to the unit and the operating activity.

Never assume that children will remain where you last saw them.

1. Keep children out of the area and under

the watchful care of another

responsible adult.

2. Be alert and turn off if children enter the area.

3. Never allow children to operate the unit.

4. Use extra care when approaching blind corners,

shrubs, trees, or

other objects that may obscure vision.

Clearing A Clogged Discharge Chute

Hand contact with the rotating impeller inside the discharge chute is the

most common cause of injury associated with snowthrowers. Never use

your hand to clean out the discharge chute.

To clear the chute:

1. SHUT OFF THE ENGINE.

2. Wait 10 seconds to be sure the impeller blades have stopped

rotating.

3. Always use a clean-out tool, not your hands.

Service, Maintenance And Storage

1. Check shear bolts and other bolts at frequent intervals for proper

tightness to be sure the equipment is in safe working condition.

2. Never store the machine with fuel in the tank inside a building where

ignition sources are present such as hot water and space heaters, or

clothes dryers. Allow the engine to cool before storing in any

enclosure.

3. Always refer to operator’s manual for important details if the

snowthrower is to be stored for an extended period.

4. Maintain or replace safety and instruction labels as necessary.

5. Run

the machine a few minutes after throwing snow to prevent

freeze-up

of

the

collector/impeller

.

6.

If

fuel

is

spilled,

do

not

attempt

to

start

the

engine

but

move

the

machine

away

from

the

area

of

spillage

and

avoid creating any source

of ignition until fuel vapors have dissipated.

7. Always observe safe refueling and fuel handling practices when

refueling the unit after transportation or storage.

8. Always follow the engine manual instructions for storage

preparations before storing the unit for both short and long term

periods.

9. Always follow the engine manual instructions for proper start-up

procedures when returning the unit to service.

10. Maintain or replace safety and instruction labels as necessary.

11. Keep nuts and bolts tight and keep equipment in good condition.

12. Never tamper with safety devices. Check their proper operation

regularly and make necessary repairs if they are not functioning

properly.

13. Components are subject to wear, damage, and deterioration.

Frequently check components and replace with manufacturer’s

recommended parts, when necessary.

14. Check control operation frequently. Adjust and service as required.

15. Use only factory authorized replacement parts when making repairs.

16. Always comply with factory specifications on

all settings and

adjustments.

17. Only authorized service locations should be utilized for major service

and repair requirements.

18. Never attempt to make major repairs on this unit unless

you have

been properly trained. Improper service procedures can result in

hazardous operation, equipment damage and voiding of

manufacturer’s warranty.

19. Check shear bolts (pins) and other bolts at frequent intervals for

proper tightness to be sure the equipment is in safe working

condition.

Emissions

1. Engine exhaust from this product contains chemicals known, in

certain quantities, to cause cancer, birth defects, or reproductive

harm.

2. If available, look for the relevant Emissions Durability Period and Air

Index information on the engine emissions label.

Ignition System

1. This spark ignition system complies with Canadian ICES-002.

RULES FOR SAFE OPERATION

7

1741062

TABLE OF CONTENTS

8

1741062

HAZARD SYMBOLS AND THE MEANINGS 2. . . . . . . . . .

OPERATING SYMBOLS AND THEIR MEANINGS 3. . . . .

OWNER’S INFORMATION 5. . . . . . . . . . . . . . . . . . . . . . . . . .

ASSEMBLY 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

TOOLS REQUIRED FOR ASSEMBLY 9. . . . . . . . . . . . . .

CONTENTS OF SHIPPING CARTON 9. . . . . . . . . . . . . .

PARTS BAGS CONTENTS: 9. . . . . . . . . . . . . . . . . . . . . . .

UNPACKING 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..

UPPER HANDLE ASSEMBLY 11. . . . . . . . . . . . . . . . . . . .

CHECK THE CABLES 11. . . . . . . . . . . . . . . . . . . . . . . . . . .

HOW TO SET THE LENGTH OF THE CABLE 11. . . . .

REMOTE CHUTE CONTROL KNOB 12. . . . . . . . . . . . . .

SPEED SELECT KNOB 12. . . . . . . . . . . . . . . . . . . . . . . . .

SNOW CHUTE ASSEMBLY 13. . . . . . . . . . . . . . . . . . . . . .

HOW TO ASSEMBLE THE DRIFT CUTTER 14. . . . . . .

OPERATION 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

OPERATING CONTROLS 15. . . . . . . . . . . . . . . . . . . . . . .

SNOW BLOWER OPERATION 16. . . . . . . . . . . . . . . . . . .

BEFORE STARTING ENGINE 17. . . . . . . . . . . . . . . . . . . .

CHECK THE OIL 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

FILL GAS 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

TO STOP ENGINE 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

TO START ENGINE 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

HOW TO CLEAR A CLOGGED DISCHARGE CHUTE 20.

HOW TO USE THE CLEAN-OUT TOOL 20. . . . . . . . . . .

OPERATING TIPS 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SERVICE RECOMMENDATIONS 22. . . . . . . . . . . . . . . . . . .

CUSTOMER RESPONSIBILITIES 23. . . . . . . . . . . . . . . . . .

SNOW BLOWER 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

LUBRICATION AT STORAGE 23. . . . . . . . . . . . . . . . . . . .

LUBRICATION − EVERY 10 HOURS 23. . . . . . . . . . . . . .

LUBRICATION − EVERY 25 HOURS 24. . . . . . . . . . . . . .

ENGINE 25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ADJUSTMENT/REPAIR 26. . . . . . . . . . . . . . . . . . . . . . . . . . .

AUGER HOUSING HEIGHT ADJUSTMENT 26. . . . . . .

TO ADJUST SCRAPER BAR 26. . . . . . . . . . . . . . . . . . . . .

TO ADJUST SKID HEIGHT 26. . . . . . . . . . . . . . . . . . . . . .

HOW TO REMOVE THE SNOW HOOD 27. . . . . . . . . . .

BELT ADJUSTMENT 28. . . . . . . . . . . . . . . . . . . . . . . . . . . .

HOW TO REPLACE THE BELTS 29. . . . . . . . . . . . . . . . .

BELT GUIDE ADJUSTMENT 32. . . . . . . . . . . . . . . . . . . . .

HOW TO CHECK AND ADJUST THE CABLES 32. . . .

AUGER DRIVE CABLE ADJUSTMENT 32. . . . . . . . . . . .

TRACTION DRIVE CABLE ADJUSTMENT 33. . . . . . . . .

HOW TO ADJUST OR REPLACE

THE FRICTION WHEEL 34. . . . . . . . . . . . . . . . . . . . . . .

AUGER SHEAR BOLT REPLACEMENT 37. . . . . . . . . . .

STORAGE 38. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

TROUBLE SHOOTING CHART 39.

. . . . . . . . . . . . . . . . . . . .

ASSEMBLY

9

1741062

TOOLS REQUIRED FOR ASSEMBLY

1 − Knife

2 − 1/2” wrenches (or adjustable wrenches)

2 − 9/16” wrenches (or adjustable wrenches)

2 − 3/4” wrenches (or adjustable wrenches)

1 − 3/8” wrenches (or adjustable wrenches)

1 − Pair pliers or screw driver (to spread cotter pin)

HOW TO MEASURE SCREW SIZE

LENGTH

DIAMETER

CONTENTS OF SHIPPING CARTON

1− Snow Blower

1− Container of Fuel Stabilizer (Located in Parts Bag)

1− Crank Assembly

1− Parts Bag

WARNING: Always wear safety glasses or eye

shields while assembling snow blower.

PARTS BAGS CONTENTS:

1 − Shift Lever Knob

(not actual size)

1 − Washer

1 − Nut

1 − Remote Chute

Knob (not actual size)

1 − Ignition Keys

* 2−1/4−20 x 1.75

* 2−Spacer

* 2−1/4−20

Hex nut

* Non Assembly parts are found in toolbox located on top of belt cover.

ASSEMBLY

10

1741062

Figure 1 shows the snow blower in the shipping position.

Figure 2 shows the snow blower completely assembled.

Reference to right and left hand side of the snow blower is

from the operator’s position at the handle.

UNPACKING

1. Locate the two tear tabs at the bottom of the carton.

2. Pull the tear tape no more than twelve inches (30.48cm.)

at a time. Re−grasp tape next to the carton and pull

again. Repeat until all the tape is torn off.

3. After the tape has been completely removed from the

carton, remove the carton from the base. Cut all four cor-

ners and fold the sides toward the center for easy dispos-

al.

4. Remove the plastic bag that covers the unit.

5. Locate and remove the parts bag.

NOTE: Set the fuel stabilizer aside until adding

gasoline to the fuel tank. We recommend that fuel

stabilizer is added to the fuel each time that gasoline

is added to the fuel tank.

6. For shipping purposes, the height adjust skids are at-

tached to the pallet. Remove the screw that secures

each height adjust skid to the pallet. (See Figure 2).

7. Roll the snow blower off the carton by pulling on the lower

handle.

CAUTION: DO NOT back over cables.

8. Remove the packing material from the handle assembly.

9. Cut ties securing the clutch control cables to the lower

handle.

NOTE: If the cables have become disconnected from the

clutch levers, reinstall the cables as shown in Figure 3.

Figure 1

Figure 2

Auger Drive

Lever

Traction Drive Lever

Snow Chute Deflector

Height Adjust

Skid

Auger Housing

Remote Chute Control

Screw

Speed Shifter Lever

Figure 3

”Z” Fitting

Drive Lever

Cable

ASSEMBLY

11

1741062

UPPER HANDLE ASSEMBLY

1. Cut tie holding shift rod to lower handle and move shifter

to the neutral position.

2. Loosen, but do not remove the screws, flatwashers, lock-

washers and hex nuts in the upper holes of the lower han-

dle.

3. Remove the fasteners from the lower holes of the lower

handle See Figure 4.

4. Raise upper handle into operating position. Upper han-

dle should be to the outside of the lower handle.

NOTE: Make sure the cables are not caught between

the upper and lower handle.

NOTE: If the cables have become disconnected form

the drive levers, reinstall the cables as shown in

Figure 5.

5. Install the fasteners that were removed in step 3. DO

NOT tighten until all bolts are in place.

6. Tighten all handle bolts.

Figure 4

Nut

Flatwasher

Bolt

Lockwasher

Figure 5

Lever

“Z” Fitting

Control Cable

CHECK THE CABLES

1. If control cables have become unattached from motor

mount frame, reconnect cables as shown in Figure 6.

2. For cable adjustments, see “How To Check And Adjust

The Cables” in the ADJUSTMENT/REPAIR section.

HOW TO SET

THE LENGTH OF THE CABLES

The cables were adjusted at the factory and no adjustments

should be necessary. However, after the handles are put in

the operating position, the cables can be too tight or too

loose. If an adjustment is necessary, see “How To Check And

Adjust The Cables” in the ADJUSTMENT/REPAIR section.

Traction Drive Cable

Auger Drive Cable

Figure 6

ASSEMBLY

12

1741062

REMOTE CHUTE CONTROL KNOB

1. Thread the knob onto the lever as far as possible. Make

sure that the knob points forward (See Figure 7).

2. Tighten the jam nut against the knob securely.

SPEED SELECT KNOB

1. Thread the knob onto the lever as far as possible. Make

sure that the knob points forward (See Figure 7).

2. Tighten the jam nut against the knob securely.

Figure 7

Nut

Lever

LIp

Knob

HOW TO INSTALL

THE SPEED CONTROL ROD

1. Put the speed select lever to the NEUTRAL position.

See Figure 8.

2. Attach the ball joint, located on the bottom end of the

speed control rod, to the shift yoke assembly. See

Figure 9. The fasteners are attached to the ball joint at

the factory.

3. The length ot the ball joint and speed control rod have

been pre−adjusted at the factory. If an adjustment is re-

quired, loosen the nut. Remove the fasteners to discon-

nect the ball joint from the shift yoke assembly. To

lengthen or shorten the speed control rod, turn the

adapter to obtain the correct length.

4. Make sure the speed select lever functions correctly.

Move the speed select lever through all speeds.

Speed Select Lever

Figure 8

Remote Chute

Control Lever

Figure 9

Speed Control Rod

Nut

Adapter

Ball Joint

Shift Yoke Assembly

Fasteners

ASSEMBLY

13

1741062

SNOW CHUTE ASSEMBLY

1. Position the snow chute to the INSIDE of the snow

chute flange. Align the three holes in the snow

chute with holes in snow chute flange (see Figure 11).

2. Place three 5/16-18 carriage bolts from the inside of

the chute as shown in figure 11 (hardware is found

in parts bag).

3. Place three 5/16-18 flat washers and three 5/16-18

nuts on the outside of the flange.

4. First tighten the rear carriage bolt, then tighten the

remaining two carriage bolts. Make sure all carriage

bolts are tight.

6. Attach the remote snow chute deflector cable

the cable chute bracket (see Figure 12) and secure

by tightening nuts (on cable) to the cable chute

bracket.

5. Attach the remote snow chute deflector cable to the

weld stud (on deflector) and secure in place using

a pushnut as shown in Figure 12 (pushnut is found

in hardware bag).

.

NOTE: check all carriage bolts in flange for tightness.

DO NOT overtighten.

Figure 10

Figure 11

Snow Chute Deflector

Snow Chute Extension

Flange

Carriage Bolt

Flat Washer

Nut

Snow Chute Deflector Cable

Pushnut

Weld Stud

Snow Chute Deflector Cable

Cable Chute Bracket

Nuts

NOTE: Before starting step 6 make sure that the chute

deflector is in the full open position and the remote

chute lever is in the full open position.

ASSEMBLY

14

1741062

HOW TO ASSEMBLE THE DRIFT CUTTER

Drift cutters are used to cut a path through snow deeper than

the auger housing.

1. Loosen the wingnuts that secure the drift cutters to the

auger housing (see Figure 12).

2. Raise the drift cutters to the desired height.

3. Tighten the wingnuts.

Drift Cutter

Wingnut

Figure 13

HOW TO SET

THE LENGTH OF THE CABLES

The cables were adjusted at the factory and no adjustments

should be necessary. However, after the handles are put in

the operating position, the cables can be too tight or too

loose. If an adjustment is necessary, see “How To Check And

Adjust The Cables” in the Service And Adjustment section.

CHECK THE TIRES

The tires were over inflated for shipment. Check the tire

pressure in the tires. See the sidewall of the tire for the

proper inflation.

IMPORTANT! BEFORE YOU START

OPERATING

r Check the fasteners. Make sure all fasteners are

tight.

r On electric start models, the unit was shipped with

the starter cord plugged into the engine. Before

operating, unplug the starter cord from the engine.

NOTE: This snow blower was shipped WITH OIL in the engine. See “Before Starting Engine” in-

structions in the Operation section of this manual before starting engine.

OPERATION

15

1741062

Get to know your snow blower and its controls. Be sure you (or any other operator) have read and understood the Operation

Precautions listed on page 2 of this manual.

Figure 12

Auger Drive Clutch Lever

Traction Drive

Clutch Lever

Speed Shift Lever

Snow Chute

Deflector

Auger Housing

Height Adjust Skid

Toolbox

Remote Chute Control

Drift

Cutter

Primer Button

Gas Fill

Starter Handle

Throttle Control

Lever

Ignition Key

Choke Lever

Scraper Bar

Shear Pin

Electric

Start Button

Clean-out Tool

Electric Chute Switch

ENGINE AND SNOW BLOWER OPERATING CONTROLS

The engine operating controls and their functions are as

follows:

Throttle Control Lever − This snow blower is equipped with

an engine mounted throttle control lever used to start a cold

engine.

Choke Lever− Set choke lever to ON CHOKE position to

start a cold engine.

Electric Start Button− Used to start the engine using the

120 volt electric starter.

Prime Button− Used to inject fuel directly into carburetor

manifold to insure fast starts in cool weather.

Ignition Key− Must be inserted into ignition key slot to start

engine. Pull out to stop. Do not turn ignition key.

Starter Handle− Starts the engine manually.

The snow blower operating controls and their functions

are as follows:

Speed Select Lever− Allows the operator to use one of six

(6) forward and two (2) reverse speeds. To shift, move speed

select lever to desired position.

NOTE: Do not move speed select lever while Traction

Drive Clutch is engaged. This may result in severe

damage to drive system.

Auger Drive Clutch Lever− Used to engage and disengage

the auger and impeller. To engage push down, to disengage

release.

Traction Drive Clutch Lever− Used to propel snow blower

forward or reverse. Push down to engage, release to

disengage.

Snow Chute Deflector− Changes the direction the snow is

blown.

Remote Chute Deflector Lever− Pull remote lever back to

discharge snow high and far. Push remote lever forward to

discharge snow down.

Electric Chute Switch − Changes the direction of snow

throwing through the discharge chute.

Height Adjust Skid− Used to adjust ground clearance of

auger housing (see To Adjust Skid Height in the

Adjustment/Repair section of this manual).

Toolbox − Spare shear pins, shear bolt wrenches and

spacers are located in toolbox.

Drift Cutters − Cuts a path through snow higher than the

auger housing.

Clean-Out Tool − Use the clean-out tool to remove snow and

debirs from the discharge chute and the auger housing.

OPERATION

16

1741062

The operation of any snow blower can result in foreign objects being thrown into the eyes,which can

result in severe eye damage. Always wear safety glasses or eye shields before beginning snow blower

Operation. We recommend standard safety glasses or Wide Vision Safety Mask for over spectacles.

SNOW BLOWER OPERATION

The most effective use of the snow blower will be established

by experience, taking into consideration the terrain, wind

conditions and building location which will determine the

direction of the discharge chute.

NOTE: Do not blow snow towards a building as hidden

objects could be blown with sufficient force to cause

damage.

1. Start the engine as described in section “To Start En-

gine”.

2. Adjust snow chute deflector. Push the remote chute le-

ver forward to discharge snow down, pull remote chute

deflector back to discharge snow high and far. (see

Figure 13).

3. Move the electric chute switch to set the direction (left to

right) of the discharge chute.

4. Select proper speed for snow conditions as outlined be-

low and set speed select lever to desired position.

NOTE: Always release traction drive clutch lever

before moving speed select lever.

Ground speed is determined by snow conditions. Select

the speed you desire by moving the speed selector into

the appropriate colored area on the control panel.

1−2 Wet, Heavy, Slushy, Extra Deep

3 Moderate

4−5 Very Light

6 Transport Only

NOTE: When clearing wet, heavy snow, it is

recommended that the ground speed of the unit be

reduced, maintain full throttle and do not attempt to

clear the full width of the unit.

For additional operating instructions see “Operating

Tips” in this section of the manual.

5. Engage auger drive clutch lever (right hand−Figure 13).

IMPORTANT: Be sure front of unit is clear of

bystanders or obstacles before operating.

6. Engage traction drive clutch lever (left hand−Figure 13).

As the snow blower starts to move, maintain a firm hold

on the handles and guide the snow blower along the cut-

ting path. Do not attempt to push the snow blower.

7. To stop forward motion, release traction drive clutch lever

(left hand − Figure 13).

8. To stop auger, release auger drive clutch lever (right

hand − Figure 13).

9. To move the snow blower backwards, move speed select

lever into first or second reverse and engage traction

drive clutch lever (left hand). To stop, release traction

drive clutch lever.

WARNING: Read Owner’s Manual before oper-

ating machine. This machine can be dangerous

if used carelessly.

Never operate the snow blower without all guards, cov-

ers, and shields in place.

Never direct discharge towards windows or allow by-

standers near machine while engine is running.

Stop the engine whenever leaving the operating posi-

tion.

Disconnect spark plug before unclogging the impeller

housing or the discharge chute and before making re-

pairs or adjustments.

When leaving the machine, remove the ignition key.

To reduce the risk of fire, keep the machine clean and

free from spilled gas, oil and debris.

Auger Drive Lever

Traction Drive LeverShift Lever

Remote Chute Lever

Figure 13

Electric Chute

Switch

OPERATION

17

1741062

BEFORE STARTING ENGINE

Check the oil

NOTE: The engine was shipped from the factory filled

with oil. Check the level of the oil. Add oil as needed.

1. Make sure the unit is level.Use a high quality detergent

oil classified “For Service SG, SH, SJ, SL, or higher”.

2. Remove the oil fill cap/dipstick and wipe with a clean

cloth (see Figure 14).

3. Insert the oil fill cap/dipstick and turn clockwise to tighten.

4. Remove the oil fill cap/dipstick and check the oil.

NOTE: Do not check the level of the oil while the

engine runs.

5. If necessary, add oil until the oil reaches the FULL mark

on the oil fill/cap dipstick (see Figure 14). Do not add too

much oil.

6. Tighten the fill cap/dipstick securely each time you check

the oil level.

NOTE: For extreme cold operating conditions of 0F

(−18 C) and below, use a synthetic 5W30 motor oil for

easier starting.

NOTE: S.A.E. 5W30 motor oil may be used to make

starting easier in areas where the temperature is 20 F.

(−7 C) to 0F (−18 C). Synthetic 5W30 is acceptable for

all temperatures. DO NOT mix oil with gasoline.

NOTE: SEE CHART FOR OIL RECOMMENDATION

0F (−18 C) and below

0F (−18 C) and above

TYPE OF OILTEMPERATURE

synthetic 5W30

S.A.E. 5W30

F − 20 0 20 32 40

C −30 −20 −10 0 10

SAE VISCOSITY GRADES

5W30

synthetic 5W30

FILL GAS

This engine is certified to operate on gasoline. Exhaust

Emission Control System: EM (Engine Modifications)

1. Fill the fuel tank with fresh, clean, unleaded regular, un-

leaded premium, or reformulated automotive gasoline

with a minimum of 85 octane along with a fuel stabilizer

(follow instructions on fuel stabilizer package). DO NOT

use leaded gasoline. We recommend that fuel stabilizer

be added to the fuel each time that gasoline is added to

the fuel tank.

NOTE: Winter grade gasoline has higher volatility to

improve starting. Be certain container is clean and

free from rust or other foreign particles. Never use

gasoline that may be stale from long periods of

storage in the container.

CAUTION: DO NOT use gasoline containing any

amount of alcohol as it can cause serious damage to

the engine or significantly reduce the performance.

2. Check to make sure that spark plug is tightened securely

into engine and spark plug wire is attached to spark plug.

If torque wrench is available, torque plug to 18−23 ft−lbs.

WARNING: Gasoline is flammable. Always use

caution when handling or storing gasoline. Do

not add gasoline to the fuel tank while snow

blower is running, hot, or when snow blower is in an en-

closed area. Keep away from open flame, electrical

sparks and DO NOT SMOKE while filling the fuel tank.

Never fill the fuel tank completely; but fill the fuel tank

to within 1-1/2 inch (3.8 mm) from the top to provide

space for the expansion of the fuel. Always fill fuel tank

outdoors and use a funnel or spout to prevent spilling.

Make sure to wipe up any spilled fuel before starting

the engine.

Store gasoline in a clean, approved container, and keep

the cap in place on the container. Keep gasoline in a

cool well ventilated place; never in the house. Never

buy more than a 30 day supply of gasoline to assure

volatility. Gasoline Is intended to be used as a fuel for

internal combustion engines; therefore, do not use

gasoline for any other purpose. Since many children

like the smell of gasoline, keep it out of their reach be-

cause the fumes are dangerous to inhale, as well as be-

ing explosive.

FULL

Figure 14

Oil Fill Cap/Dipstick

Fuel Tank

BEFORE STOPPING THE ENGINE

Run the engine for a few minutes to help dry off any moisture

on the engine.

OPERATION

18

1741062

TO STOP ENGINE

WARNING

Gasoline and its vapors are extremely

flammable and explosive.

Fire or explosion can cause severe burns or

death.

DO NOT choke the carborator to stop the

engine.

1. Move the stop switch (A, Figure 15) to the stop

position.

2. Remove the safety key (B). Keep the safety key

out of reach of children.

A

B

Figure 15. Stopping the Engine

A. On/Stop Switch

B. Safety Key

STARTING THE ENGINE

1. Check the oil level. See the Engine Manual

How

to Check/Add Oil

section

2. Make sure equipment drive controls are

disengaged.

3. Push the stop switch to the on position (A, Figure

6).

A

Figure 6. On/Stop Switch

A. On/Stop Switch Selector

4. Insert the engine key (A, Figure 17 ) into the engine

key slot and push fully in to the RUN position.

5. Turn the choke knob (B) fully clockwise if engine is

cold.

Note: Do not use the choke to start a warm engine.

6. Push the primer button (C) two times.

Note: Do not use the primer to start a warm engine.

Note: If the engine does not start after three attempts,

see the Engine Manual Troubleshooting section.

8. Electric Start: First connect the extension cord to

the power cord receptacle and then into a wall

receptacle. If additional extension cord is

required, make sure it is 3-wire.

Figure 18. Rewind Start

A. Starter Cord Handle

Figure 17. Rewind Start

A. Engine Key

B. Choke Knob

C. Primer Button

A

WARNING

Rapid retraction of the starter cord (kickback)

will pull your hand and arm toward the engine

faster than you can let go. Broken bones,

fractures, bruises or sprains could result.

When starting engine, pull the starter cord

slowly until resistance is felt and then pull

rapidly to avoid kickback.

C

A

B

7. Rewind Start: Firmly hold the starter cord handle

(A, Figure 18). Pull the starter cord handle slowly

until resistance is felt, then pull rapidly.

OPERATION

19

1741062

WARNING

If the extension cord is damaged, it must be

replaced by the manufacturer or its service

agent or a similarly qualified person to avoid to

avoid a hazard.

9. Electric Start: Depress the push button (A, Figure

19). After you start the engine, first disconnect the

extension cord from the wall receptacle and then

from the power cord receptacle (B).

CAUTION

To extend the life of the starter, use short

starting cycles (five seconds maximum.) Wait

one minute between starting cycles.

A

B

Figure 19. Electric Start

A. Starter Push Button

B. Power Cord Receptacle

Note: If the engine does not start after three attempts,

see the Engine Manual Troubleshooting section.

OPERATION

20

1741062

FROZEN STARTER

If the starter is frozen and will not turn engine:

1. Pull as much rope out of the starter as possible.

2. Release the starter handle and let it snap back against

the starter. Repeat until the engine starts.

Warm engines will cause condensation in cold weather. To

help prevent possible freeze−up of recoil starter and engine

controls, proceed as follows after each snow removal job.

1. With engine off, allow engine to cool for several minutes.

2. Pull starter rope very slowly until resistance is felt, then

stop. Allow the starter rope to recoil. Repeat three times.

3. With the engine not running, wipe all snow and moisture

from the carburetor cover in area of control levers. Also

move choke knob and starter handle several times.

4. With engine not running, wipe all snow and moisture from

carburetor cover in area of control levers. Also move

control levers backward and forward several times.

WARNING: Never run engine indoors or in en-

closed, poorly ventilated areas. Engine exhaust

contains CARBON MONOXIDE, AN ODORLESS

AND DEADLY GAS. Keep hands, feet, hair and loose

clothing away from any moving parts on engine and

snow thrower.

S Engine parts, especially the muffler, become ex-

tremely hot. Severe thermal burns can occur on con-

tact. Allow the engine to cool before touching.

S Never allow children to operate the snow thrower.

Never allow adults to operate the snow blower with-

out proper instruction.

S Keep the area of operation clear of all persons, partic-

ularly small children and pets.

S Never leave the snow blower unattended while the

engine is running. Anyone operating the engine or

equipment must carefully read and understand the

operating instructions.

IMPORTANT: After each use of the snow blower, stop the

engine, remove the safetey/ignition key, remove all

accumulated snow from the snow blower and wipe

clean. Store the snow blower in a protected area.

NOTE: Never cover snow blower while engine and

exhaust area are still warm.

HOW TO CLEAR

A CLOGGED DISCHARGE CHUTE

WARNING: Hand contact with the rotating im-

peller inside the discharge chute is the most

common cause of injury associated with snow

blowers. NEVER USE YOUR HAND TO CLEAN OUT

THE DISCHARGE CHUTE.

To Clear The Chute:

S SHUT OFF THE ENGINE!

S Wait 10 seconds to be sure that the impeller blades

have stopped rotating.

S Always use a clean-out tool, not your hands.

A clean-out tool is attached to either the handle or the top of

the auger housing (see Figure 20). Use the clean-out tool to

remove snow from the auger housing.

How To Use The Clean-Out Tool

 Release the auger drive lever.

 Pull out the safety key.

 Disconnect spark plug wire.

 Do not place your hands in the auger or discharge

chute. Use a clean-out tool to remove snow or debris.

WARNING: Blockage must be cleared only after

shutting off the snow blower and only with a

clean-out tool, not by hand.

Figure 20

Clean-out Tool

La page charge ...

Simplicity 6271200X43 Manuel utilisateur

Ce manuel convient également à

Simplicity 6271200X43 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents