Craftsman C950-52021-0 Le manuel du propriétaire

SWA/RS

owner's

manual

Model

C950-52021-0

10.5-H.P. 29 inch

CAUTION:

You must read and

understand this owner's

manual before operating

unit.

Serial No.

S _A/RS

I:RRFTSMRli

DUAL STAG

SNOW BLOWER

F-001160J SEARS CANADA INC., TORONTO, ONTARIO M5B 2B8 PrintedinU.S.A,

RULES FOR SAFE OPERATION

IMPORTANT

,_ WARNING: Always disconnect the spark plug wire and place it where it cannot make contact with _'_

spark plug to prevent accidental starting during: Preparation, Maintenance, or Storage of your

snow blower,

SAFE OPERATION PRACTICES FOR WALK-BEHIND SNOW BLOWER

DO NOT OPERATE THIS EQUIPMENT BEFORE READING THIS MANUAL

Engine Exhaust, some of its constituents, and

certain vehicle components contain or emit

chemicals known to the State of California to

cause cancer and birth defects or other repro-

ductive harm.

Battery posts, terminals and related accesso-

ries contain lead and lead compounds, chemi-

cals known to the State of California to cause

cancer and birth defects or other reproductive

harm. WASH HANDS AFTER HANDLING.

TRAINING

1. Read the operating and service instructionmanual care-

fully. Be thoroughly familiar with the controls and the

proper use of the equipment. Know how to stop the unit

and disengage the controls quickly.

2. Never allow children to operate the equipment. Never al-

low adults to operate the equipment without proper in-

struction.

3. Keep the area of operation clear of all persons, particu-

larly small children and pets.

4. Exercise caution to avoid slipping or falling especially

when operating in reverse.

PREPARATION

1. Thoroughly inspect the area where the equipment isto

be used and remove all doormats, sleds, boards, wires,

and other foreign objects.

2. Disengage all clutches before starting the engine.

3. Do not operate the equipment without wearing adequate

winter outer garments. Wear footwear that wilt improve

footing on slippery surfaces.

4. Handle fuel with care; it is highly flammable.

(a) Use an approved fuel container.

(b) Never add fuel to a running engine or hot engine.

F_01160J

.

7.

(c) Fill fuel tank outdoors with extreme care. Never fill

fuel tank indoors.

(d) Replace gasoline cap securely and wipe up spilled

fuel.

For all units with electric starting motors use electric

starting extension cords certified CSA/UL. Use only with

a receptacle that has been installed in accordance with

local inspection authorities.

Adjust the auger housing height to clear gravel or

crushed rock surface.

Under no circumstances should any adjustments be

made while the engine is running (except when specifi-

cally recommended by manufacturer).

8. Let engine and machine adjust to outdoor temperatures

before starting to clear snow.

9. Always wear safety glasses or eye shields during opera-

tion or while performing an adjustment or repair to protect

eyes from foreign objects that may be thrown from the

machine.

OPERATION

1. Do not put hands or feet near or under rotating parts.

Keep clear of the discharge opening at ait times.

2. Exercise extreme caution when operating on or crossing

gravel drives, walks or roads. Stay alert for hidden haz-

ards or traffic.

3. Never discharge snow onto public roads or near moving

traffic.

4. After striking a foreign object, stop the engine, remove

the wire from the spark plug, thoroughly inspect snow

blower for any damage, and repair the damage before re-

starting and operating the snow blower.

5. If the unit should start to vibrate abnormally, stop the en-

gine and check immediately for the cause. Vibration is

generally a warning of trouble.

6. Stop the engine and remove spark plug wire whenever

you leave the operating position, before unclogging the

auger/Impeller housing or discharge chute and when

making any repairs, adjustments, or inspections.

7. When cleaning, repairing, or inspecting, make certain

the augedlmpetler and all moving parts have stopped

and all controls are disengaged. Disconnect the spark

plug wire and keep the wire away from the spark plug to

prevent accidental starting.

RULES FOR SAFE OPERATION

8. Take all possible precautions when leaving the snow

blower unattended. Disengage the auger/impeller, shift

to neutral, stop engine, and remove key.

9. Do not run the engine indoors, except when starting the

engine and for transporting the snow blower in or out of

the building. Ensure the outside doors are open; exhaust

fumes are dangerous.

10. Do not clear snow across the face of slopes. Exercise ex-

treme caution when changing direction on slopes. Do not

attempt to clear steep slopes.

11. Never operate the snow blower without proper guards,

plates or other safety protective devices in place.

12. Never operate the snow blower near enclosures, auto-

mobiles, window wells, drop-offs, and the like without

proper adjustment of the snow discharge angle. Keep

children and pets away.

13. Do not overload the machine capacity by attempting to

clear snow at too fast a rate.

14. Never operate the machine at high transport speeds on

slippery surfaces. Look behind and use care when back-

ing up.

15. Never direct discharge at bystanders or allow anyone in

front of the unit.

16. Disengage power to the collector/impeller when snow

blower is transported or not in use.

17. Use only attachments and accessories approved by the

manufacturer of the snow blower (such as wheel

weights, counterweights, cabs, and the like).

18. Never operate the snow blower without good visibility or

light. Always be sure of your footing and keep a firm hold

on the handles.

MAINTENANCE AND STORAGE

1. Check shear bolts and otherbolts at frequent intervalsfor

propertightness to be sure the equipment isin safe work-

ing condition.

2. Never store the machine with fuel in the tank inside a

building where ignition sources are present such as hot

water and space heaters, clothes dryers, and the like. Al-

low the engine to cool before storing in any enclosure.

3. Always refer to operator's guide instructionsfor impor-

tant details if the snow blower isto be stored for an ex-

tended period.

4. Maintain or replace safety and instruction labels, as nec-

essary.

5. Run the machine 2 minutes with auger clutch lever en-

gaged after blowing snow to prevent freeze-up of the au-

ger/impeller.

WARNING: Do not

use hands to un-

clog discharge

chute.

• Stop engine/motor before removing debris.

• Do not walk in front of running machine.

• Do not discharge at bystanders.

• Keep people and pets a safe distance from the

machine.

• Before leaving machine, shut off engine/motor

and remove key.

19. Do not over-reach. Keep proper footing and balance at

all times.

20. Do not attempt to use snow blower on a roof.

WARNING: Avoid

injury from rotating

auger- keep hands,

feet, and clothing

away.

F_01160J 3

OWNER'S INFORMATION

DATE PURCHASED:

MODEL NO:

SERIAL NO:

STORE WHERE PURCHASED:

ADDRESS:

CITY: PROVINCE:

TELEPHONE :

_Record this information about your unit so that you will

be able to provide it in case of loss or theft,

MAINTENANCE AGREEMENT

The Craftsman Warranty, plus a Maintenance Agree-

ment, provide maximum value for Sears products. Con-

tact your nearest Sears store for details.

Horse Power 10.5 HP

Gasoline Capacity 4 quarts (4 litre)

Oil Capacity (5W30) 26 oz. (.77 litre)

Spark Plug: (Gap .030 in.) Champion RJ19LM

Tire Pressure 20 PSI (1,406 kg/cm 2)

See side of the tire for maximum inflation. Do not exceedthe

maximum pressure on the tire wall.

CUSTOMER RESPONSIBILITIES

Read and observe the safety rules.

Follow a regular schedule in maintaining, caring for and

using your snow blower.

Follow the instructions under "Customer Responsibilities"

and "Storage" sections of this owner's manual.

WHEELED SNOW BLOWER

LIMITED TWO (2) YEAR WARRANTY ON CRAFTSMAN SNOW BLOWER

For two (2) years from date of purchase, Sears Canada Inc. will repair or replace free of charge, at Sears option, parts

which are defective as a result of material or workmanship.

COMMERCIAL OR RENTAL USE:

Warranty on snow blower will be 90 days from date of purchase if used for commercial or rental purposes.

THIS WARRANTY DOES NOT COVER:

1. Pre-detivery set-up.

2. Expendable items which become worn during normal use, such as belts, spark plugs, filter, shear pins as well as

damages to the engine resulting from operating the snow blower with insufficient oil.

3. Tire replacement or repair caused by punctures from outside objects, such as nails, thorns, stumps or glass.

4. In home service.

Warranty service is available by returning the Craftsman snow blower to the nearest Sears Service Centre/Department

in Canada. This warranty applies only while this product is in use in Canada.

This warranty is in addition to any statutory warranty and does NOT exclude or limit legal rights you may have but shall

run concurrently with applicable provincial legislation. Furthermore, some provinces do not allow limitations on how long

an implied warranty will last so the above limitations may not apply to you.

SEARS CANADA INC., TORONTO, ONTARIO M5B 2B8

Fq)01160J 4

TABLE OF CONTENTS

RULES FOR SAFE OPERATION .................... 2

OWNER'S INFORMATION ......................... 4

ASSEMBLY ...................................... 6

TOOLS REQUIRED FOR ASSEMBLY ............. 6

CONTENTS OF SHIPPING CARTON .............. 6

PARTS BAGS CONTENTS: ...................... 6

UNPACKING ................................... 7

UPPER HANDLE AND CRANK ASSEMBLY ........ 8

CONNECT CONTROL CABLE SPRINGS .......... 8

SPEED SELECT LEVER ......................... 9

SNOW CHUTE ASSEMBLY ...................... 9

HEADLIGHT ASSEMBLY ....................... 10

OPERATION .................................... 11

ENGINE AND SNOW BLOWER OPERATING

CONTROLS ................................ 11

WHEEL LOCK OUT PIN ........................ 13

BEFORE STARTING ENGINE ................... 14

FILL OIL ...................................... 14

FILL GAS ..................................... 14

TO START ENGINE ............................ 15

COLD ENGINE START (RECOIL STARTER) ...... 15

WARM ENGINE START (RECOIL STARTER) ...... 15

USE OF ELECTRIC STARTER .................. 16

COLD ENGINE START (ELECTRIC STARTER) .... 16

WARM ENGINE START (ELECTRIC STARTER) ... 17

OPERATING TIPS ............................. 18

SERVICE RECOMMENDATIONS .................. 19

CUSTOMER RESPONSIBILITIES .................. 20

SNOW BLOWER .............................. 20

AS REQUIRED ................................ 20

LUBRICATION AT STORAGE ................... 20

LUBRICATION - EVERY 10 HOURS ............. 20

LUBRICATION - EVERY 25 HOURS ............. 21

ENGINE ...................................... 22

ADJUSTMENT/REPAIR ........................... 23

AUGER HOUSING HEIGHT ADJUSTMENT ....... 23

TO ADJUST SCRAPER BAR .................... 23

TO ADJUST SKID HEIGHT ..................... 23

BELT ADJUSTMENT ........................... 24

TRACTION DRIVE BELT ....................... 24

AUGER DRIVE BELT .......................... 24

BELT REPLACEMENT .......................... 25

AUGER DRIVE BELT .......................... 25

TRACTION DRIVE BELT ....................... 25

BELT GUIDE ADJUSTMENT .................... 26

CABLE ADJUSTMENT -

TRACTION DRIVE AND AUGER DRIVE ........ 26

FRICTION WHEEL ADJUSTMENT ............... 27

FRICTION WHEEL REPLACEMENT ............. 28

AUGER SHEAR BOLT REPLACEMENT .......... 29

SPARK PLUG ADJUSTMENT ................... 29

STORAGE ...................................... 30

TROUBLE SHOOTING CHART .................... 31

REPAIR PARTS .................................. 32

PARTS ORDERING SERVICE ..................... 53

ORDER REPAIR PARTS .......................... 54

F_01160J 5

ASSEMBLY

TOOLS REQUIRED FOR ASSEMBLY

1 - Knife

2 - 1/2" wrenches (or adjustable wrenches)

2 - 9/16" wrenches (or adjustable wrenches)

2 - 3/4" wrenches (or adjustable wrenches)

1 - 3/8" wrenche (or adjustable wrench)

1 - Pair pliers or screw driver (to spread cotter pin)

CONTENTS OF SHIPPING CARTON

1- Snow Blower

1- Bottle of Fuel Stabilizer

1- Snow Chute Assembly

1- Crank Assembly

1- Parts Bag

HOW TO MEASURE SCREW SIZE

LENGTH

DIAMETER

4_lb WARNING: Always wear safety glasses or eye

shields while assembling snow blower.

PARTS BAGS CONTENTS:

\

1- 3/8-16 x 2.00 inch Screw

\

3- 5/16-18 3- 5/16-18

Carriage Bolts Flatwashers

1- 3/8-16

Lockwasher

3- 5/16-18

Nylon Hexnuts

1- 3/8-16 1-3/8-16

Flatwasher Hex nut

1- Cable Tie

1- Starter Cord

* 2 - Wrenches

1- Shifter Knob 1- 3/8-16 Hex Jam Nut

*Non Assembly parts are found in toolbox located on top of belt cover.

F_01160J 6

* 2-1/4-20 x 1.75

* 2-Spacer

* 2-1/4-20

Hex nut

ASSEMBLY

Figure 1 shows the snow blower in the shipping position.

Figure 2 shows the snow blower completely assembled.

Reference to right and left hand side of the snow blower is

from the operator's position at the handle.

UNPACKING

1. Locate the two tear tabs at the bottom of the carton.

2. Pull the tear tape no more than twelve inches (30.48cm.)

at a time. Re-grasp tape next to the carton and pull

again. Repeat until all the tape is torn off.

3. After the tape has been completely removed from the

carton, remove the carton from the base. Cut all four cor-

ners and fold the sides toward the center for easy dispos-

al.

4. Remove the plastic bag that covers the unit.

5. Locate and remove the fuel stabilizer and the parts bag.

NOTE: Place fuel stabilizer in a safe place until

needed for storage.

6. Cut and discard the plastic ties securing the chute crank

rod and if equipped the speed select rod.

7. For shipping purposes, the height adjust skids are at-

tached to the pallet. Remove the screw that secures

each height adjust skid to the pallet. (See Figure 2).

8. Roll the snow blower off the carton by pulling on the lower

handle.

CAUTION: DO NOT back over cables.

9. Remove the packing material from the handle assembly.

10. Cut ties securing the clutch control cables to the lower

handle.

NOTE: If the cables have become disconnected from the

clutch levers, reinstall the cables as shown in Figure 3.

Auger Drive

Clutch Lever

Headl

Assembly

Speed

Selector

Lever

Traction Drive

Traction

Drive Cable

Crank

Figure 1

Drive

Cable

Snow Chute

Deflector

_rHousing

Skid

Figure 2

"Z" Fit

Cable

Traction Drive Lever

Figure 3

Fq)01160J 7

ASSEMBLY

UPPER HANDLE AND CRANK ASSEMBLY 11. Tightenall handle bolts.

1. Loosen, but do not remove the screws, flatwashers, lock-

washers and hex nuts inthe upper holes of the lower han-

dle.

2. Raise upper handle into operating position. Upper han-

dle should be to the outside of the lower handle.

NOTE: Make sure the cables are not caught between

the upper and lower handle.

3. Install hardware supplied inthe parts bag (bolt, flatwash-

er, Iockwasher, and hex nut) into right lower hole of upper

handle (See Figure 4). Do not tighten until all bolts are in

place.

4. Locate crank assembly removed from carton eadier and

remove the 3/8" nylon Iocknut and flatwasher from the

eye bolt assembly.

5. Install the eye bolt through the lower hole on the left hand

side of the handle. (See Figure 4).

6. Install the 3/8" flatwasher and the 3/8" nylon locknut.

7. Carefully remove cotter pin, clevis pin, and universal joint

pin from yoke end of crank rod assembly. (Figure 5)

8. Place universal joint into end of worm gear lining up large

holes. Insert the universal joint pin. Make sure the open-

ing in pin is in line with small openings in universal joint.

9. Place yoke end of crank rod around universal joint lining

up openings. Insert clevis pin through assembly and se-

cure with cotter pin. Spread ends of cotter pin to lock in

place.

10. Tighten nut on eye bolt, keeping eye in line with the rod

while tightening the inside securely.

NOTE: Make sure crank does not touch carburetor

cover.

Adap_rBo_

Eye Bolt

3/8" Nylon

_JLocknut

/

_" 3/8-16 x

"", 2" Bolt

3/8" /

Lockwasher_ ID

3/8Nut

\

11/32 "Flatwasher

Flatwasher

Figure 4

Crank Rod

Assembly

Drilled Pin

Figure 5

CONNECT CONTROL CABLE SPRINGS

1. If control cable springs have become unattached from

motor mount frame, reconnect cables as shown in

Figure 6.

2. For cable adjustments, see "Cable Adjustment" in the

ADJUSTMENT/REPAIR section.

HOW TO SET

THE LENGTH OF THE CABLES

The cables were adjusted at the factory and no adjustments

should be necessary. However, after the handles are put in

the operating position, the cables can be too tight or too

loose. If an adjustment is necessary, see "How To Check And

Adjust The Cables" in the Service And Adjustment section.

Figure 6

F_)O1160J 8

ASSEMBLY

SPEED SELECT LEVER

1. Cut plastic tie securing speed select lever assembly to

the shifter bracket. (See Figure 7)

2. Remove locknut, washer, spring, and the bolt. (See

Figure 9)

3. Position speed selector lever assembly as shown in

Figure 8.

4. Reinstall bolt, spring, washer and locknut. (See Figure 9)

5. Tighten Iocknut until 1/8 to 3/16 inch of the bolt threads

protrude past the tocknut.

6. Thread the 3/8-16" hexjam nut onto the lever until the

nut reaches the end of the thread. (See Figure 9)

7. Thread the plastic knob as far as possible and ensure

that the knob points forward.

8. Tighten the 3/8-16" hex jam nut against the knob secure-

ly.

9. Move shifter through ait speeds to ensure proper tension

of the spring. If shifter lever sticks in any of the notches,

loosen locknut 1/2 turn at a time until shifter lever moves

more freely.

10. If adjustment of speed of snow blower is needed, refer to

"Friction Wheel Adjustment" in the ADJUSTMENT/RE-

PAIR section.

NOTE: View is from rightside of unit standing in operator's position.

stic oo

forward) Shifter Bracket

Control Panel

Locknut

1/8to3/16inchof

Exposed Thread

Figure 9

SNOW CHUTE ASSEMBLY

1. Position the snow chute onto the snow chute flange. Al-

ign the three holes in the snow chute with holes in snow

chute flange. (See Figure 1)

Shifter Bracket

Plastic Tie

Shift Lever

Figure 7

Shifter Bracket

Control Panel

Figure 8

2. Place three 5/16-18 carriage bolts from inside of chute

as shown in Figure 1. (hardware is found in parts bag)

3. Place three 5/16-18 flatwashers and three 5/16-18 nuts

on outside of flange.

4. Tighten all four carriage bolts securely.

NOTE: DO NOT overtigten carriage bolts.

Snow Chute Deflector

Chute Extension

Nut

Flange_

Bolts

Not Remove

Hardware Figure 10

Fq)O1160J 9

ASSEMBLY

HEADLIGHT ASSEMBLY

The headlight is mounted on the right side of the upper

handle. It is installed upside-down for shipping purposes.

1. Remove the nut and lock washer from the carriage bolt.

2. Turn the headlight to the top side of the upper handle. En-

sure external tooth lock washer and saddle washer are

in place as shown in Figure 11.

3. Install the nut and lock washer to secure the headlight to

the handle. The headlight should point toward the snow

clearing path.

4. Attach the headlight cable with cable tie found in parts

bag to the right handle as shown in Figure 11.

External Toot

Lockwasher

Lockwasher_-_

Hex Nut

Figure 11

I

NOTE: This snow blower was shipped WITH OIL in the engine. See "Before Starting Engine" in-

structions in the Operation section of this manual before starting engine,

F_01160J 10

OPERATION

Get to know your snow blower and itscontrols. Be sure you (or any other operator) have read and understood the Operation

Precautions listed on page 2 of this manual.

Traction Drive

Auger Ddve Clutch Lever

Clutch Lever

Oil Fill Cap/Dipstick

Electric Start Button

Primer Button

Carburetor

Cover

Headlight

Assembly

Speed

Select

Lever

Traction Drive

Cable

Crank

Assembly

Choke \

Ignition Key

Throttle Control

Lever

Starter Handle

Drive

Cable

Deflector

Auger Housing

Height

Adjust Skid

Figure 12

ENGINE AND SNOW BLOWER OPERATING CONTROLS

The engine operating controls and their functions are as

follows:

Throttle Control Lever - This snow blower isequipped with

an engine mounted throttle control lever used to start a cold

engine.

Choke Lever- Set choke lever to ON CHOKE position to

start a cold engine.

Electric Start Button- Used to start the engine using the

120 volt electric starter.

Prime Button- Used to inject fuel directly into carburetor

manifold to insure fast starts in cool weather.

Ignition Key- Must be inserted into ignition key slot to start

engine. Pull out to stop. Do not turn ignition key.

Starter Handle- Starts the engine manually.

The snow blower operating controls and their functions

are as follows:

Speed Select Lever- Allows the operator to use one of six

(6) forward and two (2) reverse speeds. To shift, move speed

select lever to desired position.

Fq)01160J 11

NOTE: Do not move speed select lever while Traction

Drive Clutch is engaged. This may result in severe

damage to drive system.

Auger Drive Clutch Lever- Used to engage and disengage

the auger and impeller. To engage push down, to disengage

release.

Traction Drive Clutch Lever- Used to propel snow blower

forward or reverse. Push down to engage, release to

disengage.

Snow Chute Deflector- Changes the direction the snow is

blown.

Crank- Used to change direction of the snow discharge.

Turn handle clockwise to turn chute to right. Turn handle

counter clockwise to turn chute to left.

Height Adjust Skid- Used to adjust ground clearance of

auger housing (see To Adjust Skid Height in the

Adjustment/Repair section of this manual).

Toolbox - Spare shear pins, shear bolt wrenches and

spacers are located in toolbox.

OPERATION

_ The operation of any snow blower can result in foreign objects being thrown into the eyes,which can

result in severe eye damage. Always wear safety glasses or eye shields before beginning snow blower

Operation. We recommend standard safety glasses or Wide Vision Safety Mask for over spectacles.

SNOW BLOWER OPERATION

The most effective use of the snow blower will be established

by experience, taking into consideration the terrain, wind

conditions and building location which will determine the

direction of the discharge chute.

NOTE: Do not blow snow towards a building as hidden

objects could be blown with sufficient force to cause

damage.

1. Start the engine as described in section "To Start Engine"

(see Figure 15).

2. Adjust snow chute deflector. Loosen wing nut on the side

of the snow chute and raise chute deflector for more dis-

tance. Tighten wing nut. (see Figure 14).

_lb WARNING: Read Owner's Manual before oper-

ating machine. This machine can be dangerous

if used carelessly.

Never operate the snow blower without all guards, cov-

ers, and shields in place.

Never direct discharge towards windows or allow by-

standers near machine while engine is running.

Stop the engine whenever leaving the operating posi-

tion.

Disconnect spark plug before unclogging the impeller

housing or the discharge chute and before making re-

pairs or adjustments.

When leaving the machine, remove the ignition key.

To reduce the risk of fire, keep the machine clean and

free from spilled gas, oil and debris.

3. Using crank, position the discharge chute to discharge

snow with the wind.

4. Select proper speed for snow conditions as outlined be-

low and set speed select lever to desired position.

NOTE: Always release traction drive clutch lever

before moving speed select lever.

ENGINE WILL NOT

START UNLESS

IGNITION KEY IS

INSERTED INTO

IGNITION SLOT IN

CARBURETOR COVER.

DO NOT TURN

IGNITION KEY.

Figure 13

Ground speed is determined by snow conditions. Select

the speed you desire by moving the speed selector into

the appropriate colored area on the control panel.

Red Wet, Heavy, Slushy, Extra Deep

Amber Moderate

White Very Light

Green Transport Only

NOTE: When clearing wet, heavy snow, it is

recommended that the ground speed of the unit be

reduced, maintain full throttle and do not attempt to

clear the full width of the unit.

For additional operating instructions see "Operating

Tips" in this section of the manual.

5. Engage auger drive clutch lever (right hand-Figure 15).

IMPORTANT: Be sure front of unit is clear of

bystanders or obstacles before operating.

6. Engage traction drive clutch lever (left hand-Figure 15).

As the snow blower starts to move, maintain a firm hold

on the handles and guide the snow blower along the cut-

ting path. Do not attempt to push the snow blower.

F_01160J 12

Tee Knobs

Figure 14

Traction Drive

Clutch Lever

Dise ngaged_____---_

#L lf

Engaged

Auger Drive

Clutch Lever

. Disengaged

{- _....... -_'_._'_.4

_/ Engaged

Figure 15

OPERATION

7. To stop forward motion, release traction drive clutch lever

(left hand - Figure 15).

8. To stop the auger, release auger drive clutch lever (right

hand - Figure 15).

9. To move the snow blower backwards, move speed select

lever into first or second reverse and engage traction

drive clutch lever (left hand). To stop, release traction

drive clutch lever.

WARNING: Never run engine indoors or in an

enclosed, poor ventilated area. Engine exhaust

contains CARBON MONOXIDE, an OR-

DERLESS and DEADLY GAS.

Keep hands, feet, hair and loose clothing away from

any moving parts on engine and snow blower.

Temperature of muffler and nearby areas can exceed

150 ° F (66 ° C). Avoid these areas.

DO NOT allow children or young teenagers to operate

or be near snow blower while it is operating.

WHEEL LOCK OUT PIN

1. The left hand wheel is secured to the axle with a klick pin.

This unit was shipped with this klick pin inthe locked posi-

tion. (Figure 16).

Locked

Position

Figure 16

2. For ease of maneuverability when lighter conditions pre-

vail, remove klick pin from wheel locked position and in-

sert into single wheel drive (unlocked) position

(Figure 17). Make sure that the klick pin is in the single

wheel drive position of the axle only and not through the

locked position.

Single Wheel

Drive Position

(Unlocked)

Figure 17

NOTE: Check tire pressure (20 pounds). See side of tire

for maximum inflation. Do not exceed listed maximum

pressure.

_lb WARNING: Do not attempt to remove any item

that may become lodged in auger without tak-

ing the following precautions:

• Release auger and drive clutch levers.

• Move throttle lever to STOP position.

• Remove the ignition key.

• Disconnect the spark plug wire.

• Do not put your hands in the auger or

discharge chute. Use a pry bar.

F_01160J 13

OPERATION

BEFORE STARTING ENGINE

Check the oil

NOTE: The engine was shipped from the factory filled

with oil. Check the level of the oil. Add oil as needed.

1. Make sure the unit is level.

2. Remove the oil fitl cap/dipstick. Check the oil.

NOTE: Do not check the level of the oil while the

engine runs.

3. If necessary, add oil until the oil reaches the FULL mark

on the oil fill/cap dipstick (see Figure 18). Do not add too

much oil.

NOTE: For extreme cold operating conditions of O°F

(-18 ° C) and below, use a synthetic OW3Omotor oil for

easier starting.

NOTE: S.A.E. 5W30 motor oil may be used to make

starting easier in areas where the temperature is 20 ° F.

(-7 ° C) to O°F (-18 ° C).

NOTE: SEE CHART FOR OIL RECOMMENDATION

TEMPERATURE TYPE OF OIL

20 ° F. to O°F

(-7 ° C) to (-18 ° C) S.A.E. 5W30

0OF

(-18 ° C) and below synthetic O W3O

SAE VISCOSITY GRADES

°F 20 0 20 32 40

I I I I I

I • • I •

°C -30 -20 -10 0 10

WARNING: Gasoline is flammable. Always use

caution when handling or storing gasoline. Do

not add gasoline to the fuel tank while snow

blower is running, hot, or when snow blower is in an en-

closed area. Keep away from open flame, electrical

sparks and DO NOT SMOKE while filling the fuel tank.

Never fill the fuel tank completely; but fill the fuel tank

to within 1/4-1/2 inch (6.5-12.5 mm) from the top to pro-

vide space for the expansion of the fuel. Always fill fuel

tank outdoors and use a funnel or spout to prevent spil-

ling. Make sure to wipe up any spilled fuel before start-

ing the engine.

Store gasoline in a clean, approved container, and keep

the cap in place on the container. Keep gasoline in a

cool well ventilated place; never in the house. Never

buy more than a 30 day supply of gasoline to assure

volatility. Gasoline Is intended to be used as a fuel for

internal combustion engines; therefore, do not use

gasoline for any other purpose. Since many children

like the smell of gasoline, keep it out of their reach be-

cause the fumes are dangerous to inhale, as well as be-

ing explosive.

Oil Fill

%

Figure 18

FILL GAS

1. Fill the fuel tank with a fresh, clean, unleaded regular, un-

leaded premium, or reformulated automotive gasoline

only. DO NOT use leaded gasoline.

NOTE: Winter grade gasoline has higher volatility to

improve starting. Be certain container is clean and

free from rust or other foreign particles. Never use

gasoline that may be stale from long periods of

storage in the container.

CAUTION: DO NOT use gasoline containing any

amount of alcohol as it can cause serious damage to

the engine or significantly reduce the performance.

2. Check to make sure that spark plug istightened securely

into engine and spark plug wire is attached to spark plug.

If torque wrench is available, torque plug to 18-23 ft-lbs.

Fq)01160J 14

BEFORE STOPPING THE ENGINE

Run the engine for a few minutes tohelp dry offany moisture

on the engine.

To help avoid possiblefreeze-up of the starter, proceed as

follows:

Recoil Starter

With the engine running, pull the starter rope with a rapid

continuousfull arm stroke three or four times.

NOTE: The normal sound made by pulling the starter

rope will not harm the engine or the starter.

Electric Starter

1. Connect the power cord to the switchbox and then to a

walt outlet.

2. With the engine running, push the starter button and spin

the starter for several seconds.

OPERATION

NOTE: The normal sound made by spinning the

starter will not harm the engine or the starter.

3. Disconnect the power cord from the receptacle first and

then from the switchbox.

TO START ENGINE

Be sure that engine has sufficientoil.

The snow blower engine is equipped with a recoil starter.

Cap/Dipstick

Primer Button

Carburetor

Cover

Starter Handle

Ignition

Key

Throttle Control Lever Figure 19

COLD ENGINE START (RECOIL STARTER)

(SEE FIGURE 19)

(Engine has not been run recently.)

1. Be sure auger drive clutch lever and traction drive clutch

lever are in the disengaged (RELEASED) position.

2. iN TEMPERATURES ABOVE 0°F (-18°C)

Move throttle control to'FAST" position.

IN TEMPERATURES BELOW 0°F (-18°C)

Move throttle control to "1/2 THROTTLE" position. Be-

fore engaging auger drive clutch lever allow engine to

idle for five minutes to allow engine oil to warm. Failure

to allow engine oil to warm can cause damage to engine.

3. Insert key into ignitionslot. Make sure it snaps into place

(Figure 19). Do not turn key.

4. Rotate choke knob to the on position.

5. Push the primer button as follows:

Above 50° F (10 ° C), DO NOT PRIME.

From 50° F (10° C) to 15°F (-10 ° C), PUSH TWO TIMES.

Below 15° F (-10 ° C), PUSH FOUR TIMES.

NOTE: Cover the vent hole when as you push the

primer. Remove your finger from the primer vent

hole between pushes.

6. Pull starter handle (Figure 19) rapidly, and allow to re-

wind slowly while maintaining firm grip on handle.

7. As engine warms up move choke lever to "1/2 choke"

position. When engine does not run smoothly, move

choke lever to the off position.

F_01160J 15

.

9.

NOTE: Allow the engine to warm up for several

minutes before blowing snow in temperatures below

O°F (-18 ° C).

Run engine at or near top speed.

To stop engine, move throttle control lever to stop posi-

tion. Remove key. Do not turn key.

WARM ENGINE START (RECOIL STARTER)

(Engine still warm from recent running.)

1. Be sure auger drive clutch lever and traction drive clutch

lever are in the disengaged (RELEASED) position.

2.

3.

4.

5.

6.

7.

.

9.

IN TEMPERATURES ABOVE 0°F (-18°C)

Move throttle control to'FAST" position.

IN TEMPERATURES BELOW 0°F (-18°C)

Move throttle control to "1/2 THROTTLE" position. Allow

engine to idle at "1/2 Throttle" for five minutes to allow en-

gine oil to warm before engaging auger drive clutch lever.

Failure to allow engine oil to warm can cause damage to

engine.

Insert key intoignitionslot. Make sure it snaps into place

(Figure 19). Do not turn key.

CHOKE KNOB must be in the off position. Do not use

primer button.

Pull starter handle (Figure 19) rapidly, and allow to re-

wind slowly while maintaining firm grip on handle.

If engine fails to start after a reasonable number of start-

ing attempts, rotate choke knob to the on position and re-

peat instruction number 5.

As engine warms up, move the choke lever to the "1/2

choke" position. When engine does not run smoothly,

move choke lever to the off position.

NOTE: Allow the engine to warm up for several

minutes before blowing snow in temperatures below

O°F (-18 ° C).

Run engine at or near top speed.

To stop engine, move throttle control lever to stop posi-

tion. Remove ignition key. Do not turn the ignition key.

To help prevent possible freeze-up of recoil starter and

engine controls, proceed as follows after each snow removal

job.

1.

With engine running,pull starter rope hard with a continu-

ous full arm stroke three or four times. Pulling of starter

rope will produce a loud clattering sound. This is not

harmful to the engine or starter.

2. With engine not running, wipe all snow and moisture from

carburetor cover in area of control levers. Also move

control levers backward and forward several times.

IMPORTANT: After each use of the snow blower, stop the

engine, remove the ignition key, remove all accumulated

snow from the snow blower and wipe clean. Store the

snow blower in a protected area.

NOTE: Never cover snow blower while engine and

exhaust area are still warm.

OPERATION

USE OF ELECTRIC STARTER

On models so equipped

,_ WARNING: The electric starter is equipped with

a three-wire power cord and plug designed to

operate on 120 volt AC house hold current. The

power cord must be properly grounded at all times to

avoid the possibility of electric shock which can cause

injury to the operator. Follow all instructions carefully

as set forth below:

Make sure your house has a three-wire grounded sys-

tem. If you are not sure, ask a licensed electrician. If

your house does not have a three-wire grounded sys-

tem, do not use this electric starter under any condi-

tion.

If your house has a three-wire grounded system but a

three hole receptacle is not available to connect the

electric starter, have a three-hole receptacle installed

by a licensed electrician.

Starter Button

Power cord

Figure 21

WARNING: To connect a 120 volt power cord,

always connect the power cord first to the

switch box located on the engine and then plug

the other end into a three-hole grounded receptacle.

,_ WARNING: To disconnect the power cord, al-

ways unplug the end connected to the three-

hole grounded receptacle first.

Primer Button

Carburetor

Cover

Fill Cap/Dipstick

Starter Handle

Ignition

Key Throttle Control Lever Figure 20

COLD ENGINE START (ELECTRIC STARTER)

(SEE FIGURE 20 AND FIGURE 21)

(Engine has not been run recently.)

NOTE: When using the 120 volt electric starter, do not

push the primer button.

1.

2.

Be sure auger drive clutch lever and traction drive clutch

lever are in the disengaged (RELEASED) position.

IN TEMPERATURES ABOVE 0°F (-18°C)

Move throttle control to'FAST" position.

IN TEMPERATURES BELOW 0°F (-18°C)

Move throttle control to "1/2 THROTTLE" position. Allow

engine to idle at "1/2 Throttle" for five minutes to allow en-

gine oil to warm before engaging auger drive clutch lever.

Failure to allow engine oil to warm can cause damage to

engine.

3. Insert key intoignitionslot. Make sure it snaps into place

(Figure 20). Do not turn key.

4.

5.

6.

CHOKE KNOB must be in the off position.

Connect POWER CORD to SWITCH BOX (Figure 21).

Plug other end of POWER CORD into a three-hole,

GROUNDED 120 VOLT, AC receptacle. (See WARNING

at beginning of these instructions).

NOTE: Cover vent hole when pushing primer.

Remove finger from primer vent hole between

pushes.

7.

Push the primer button as follows:

Above 50° F (10 ° C), DO NOT PRIME.

From 50° F (10° C) to 15°F (-10 ° C), PUSH TWO TIMES.

Below 15° F (-10 ° C), PUSH FOUR TIMES.

8. START ENGINE:

F_01160J 16

OPERATION

2.

a. Push STARTER BUTTON (Figure 21) to engage

starter motor and crank engine.

b. Rotate CHOKE KNOB to the on position while crank-

ing engine.

NOTE: The electric starter is thermally protected. If

overheated, the electric starter will stop

automatically and can only be restarted when it has

cooled to a safe temperature. A wait of

approximately five to ten minutes is required.

c. When engine starts, release the STARTER BUT-

TON and rotate the CHOKE KNOB gradually to the

off position.

d.

e.

If engine falters, rotate the CHOKE KNOB immedi-

ately to the on position and then gradually to the off

position.

Disconnect the POWER CORD from receptacle first,

and then from the SWITCH BOX.

9. When the engine starts, release the starter button and

move choke lever to "1/2 choke" position. When engine

does not run smoothly, move choke lever to the off posi-

tion.

NOTE: Allow the engine to warm up for several

minutes before blowing snow in temperatures below

0OF.

10. Run engine at or near top speed.

11. To stop engine, move throttle control lever to stop posi-

tion. Remove key. Do not turn key.

If, after following the preceding instructions,your engine fails

to start, have it checked by an Authorized Sears Service

Outlet.

WARM ENGINE START (ELECTRIC STARTER)

(Engine still warm from recent running.) Proceed with the

following instructions.

NOTE: Warm engine may start without choking.

1. Be sure auger drive clutch lever and traction drive clutch

lever are in the disengaged position, "RELEASED".

IN TEMPERATURES ABOVE 0°F (-18°C)

Move throttle control to'FAST" position.

IN TEMPERATURES BELOW 0°F (-18°C)

Move throttle control to "1/2 THROTTLE" position. Allow

engine to idle at "1/2 Throttle" for five minutes to allow en-

gine oil to warm before engaging auger drive clutch lever.

Failure to allow engine oil to warm can cause damage to

engine.

3. Insert key intoignitionslot. Make sure it snaps into place

(Figure 17). Do not turn key.

4. CHOKE KNOB must be in the off position.

5. Connect the POWER CORD to the SWITCH BOX

(Figure 21).

6. Plug other end of POWER CORD into a three hole,

GROUNDED 120VOLT, AC receptacle (See "WARN-

ING" at beginning of these instructions).

7. START ENGINE:

a. Push STARTER BUTTON (Figure 21) to engage

starter motor and crank engine.

b. While cranking, rotate the CHOKE KNOB on the en-

gine to the on position.

NOTE: The electric starter is thermally protected. If

overheated, the electric starter will stop

automatically and can only be restarted when it has

cooled to a safe temperature. A wait of

approximately five to ten minutes is required.

c. When the engine starts, release the STARTER BUT-

TON and rotate the CHOKE KNOB gradually to the

off position.

d. If the engine falters, rotate CHOKE KNOB immedi-

ately to the on position and then gradually to the off

position.

e. Disconnect the POWER CORD from the receptacle

first and then from the SWITCH BOX.

8. Run the engine at or near top speed.

9. To stop the engine, move the throttle control lever to the

"Stop" position. Remove the ignition key. Do not turn key.

If after following the preceding instructions, your engine fails

to start, have the engine checked by an Authorized Sears

Service Outlet.

NOTE: Do not lose the ignition key. Key the ignition key

is a safe place. The engine will not start without the

ignition key,

F_01160J 17

OPERATION

OPERATING TIPS

1. For optimum snow blower efficiency, adjust ground

speed, not the throttle. REMEMBER - if the wheels slip,

forward speed will be reduced. The engine is designed

to deliver optimum performance at full throttle and must

be run at this power setting at all times.

2. Most efficient snowblowing is accomplished when snow

is removed immediately after it falls.

3. For complete snow removal, slightly overlap each swath

previously taken.

4. Snow should be discharged downwind whenever pos-

sible.

5. For normal usage, set the skids one-eighth inch (3 mm)

below the scraper bar. For extremely hard-packed snow

surfaces, the skids may be adjusted upward to insure

cleaning efficiency.

6. On gravel or crushed rock surfaces, the skids should be

set at 1-1/4 inch (32 mm) below the scraper bar (see To

Adjust Skid Height, in the Adjustment/Repair section in

this manual). Rocks and gravel must not be picked up

and thrown by the machine.

7. After the snowblowing job has been completed, allow the

engine to idle for a few minutes, to melt snow and ice ac-

cumulated on the engine.

8. Remove ice and snow accumulation from the entire s-

now blower to prevent obstructions and possible dam-

age when snow blower is subsequently operated.

9. Before starting snow blower, always inspect augers and

impeller for ice accumulation and/or debris, which could

result in snow blower damage.

10. Check oil level before every start, fill to "SAFE" indication

prior to operating snow blower.

To help avoid possible freeze-up of starter, proceed as

follows:

Recoil Starter:

With engine running, pull starter rope with a rapid continuous

full arm stroke three (3) or four (4) times.

NOTE: The unusual sound made by pulling starter rope

will not harm the engine orthe starter.

Electric Starter:

1. Connect the "POWER CORD" tothe "SWITCH BOX" and

then to a 120 volt AC receptacle.

2. With engine running, push the "STARTER BUTTON"

and spin the starter for several seconds.

NOTE: The unusual sound made by spinning the

starter rope will not harm the engine or the starter.

3. Disconnect the "POWER CORD" from the receptacle

first and then from the "SWITCH BOX".

Fq)01160J 18

SERVICE RECOMMENDATIONS

FIRST BEFORE EVERY EVERY EVERY BEGINNING

2 EACH 5 10 25 EACH BEFORE

PROCEDURE HOUR USE OFTEN HOURS HOURS HOURS SEASON STORAGE

S Tighten all screws and nuts _ _ _/

N Check Traction Clutch

Cable Ad ustment _/ _/

O (See Cabe Adustment)

W

Check Auger clutch Cable

B Ad ustment _/ _/

L (See Cabe Adustment)

O Adjust Drive Belts _/ _/ _/

W

E Lubricate Chains and _/

Hex Shaft

R

Lubricate Auger Shaft (See _/

Shear Bolt Replacement)

E

N Oil, Check _ _ _/

G

I

N Oil, Change q q _/

E

The warranty on this snow blower does not cover items that

have been subjected to operator abuse or negligence. To re-

ceive full value from the warranty, operator must maintain

snow blower as instructed in this manual. The following Ser-

vice Recommendations is supplied to assist operator to

properly maintain snow blower. This is a check list only. Ad-

justment referred to will be found in Adjustments/Repairs

section of this manual.

AFTER EACH USE

1. Check for any loose or damaged parts.

2. Tighten any loose fasteners.

3. Check and maintain the auger.

4. After each use, remove all snow and slush off the snow

blower to prevent freezing of auger or controls.

5. Check controls to make sure they are functioning proper-

ly.

6. If any parts are worn or damaged, replace immediately.

F_01160J 19

CUSTOMER RESPONSIBILITIES

Some adjustments will need to be made periodically to

properly maintain your snow blower.

Atl adjustments in ADJUSTMENTS/REPAIRS section of this

manual should be checked at least once each season.

SNOW BLOWER

The following adjustment should be performed more than

once each season.

Auger and Traction Drive Belts should be adjusted after the

first 2 to 4 hours of use, again about mid-season and twice

each season thereafter (See ToAdjust Belts paragraph in the

Adjustment/Repair section).

AS REQUIRED

Auger Gear Box

The auger gear box is lubricated at the factory and should not

require additional lubrication.

If for some reason the lubricant should leak out, or if the auger

gear box has been serviced, add Lubriplate GR132 Grease

or equivalent. Maximum 3-1/4 ounces, (92 grams) should be

used.

Remove filler plug D (Figure 22 and Figure 23), once a year.

If grease is visible, do not add. Ifgrease is not visible, use a

piece of fine wire, like a dipstick to check if there is grease in

the gear box. Mobitux EP1 and Shell Atdania EP1 are

suitable equivalents.

D

Filler

Plug

Figure 22

Figure 23

LUBRICATION AT STORAGE

Bearings and bushings

All bearings and bushings are lifetime lubricated and require

no maintenance.

Hex shaft and chains

For storage hex shaft should be wiped with a cloth lightly

moistened with motor oil to prevent rusting (see Figure 25).

For storage chains should be lubricated with a chain type

lube. (see Figure 25).

NOTE: Any greasing or oiling of the above mentioned

components can cause contamination of the rubber

friction wheel. If the disc drive plate or friction wheel

come in contact with grease or oil damage to rubber

friction wheel will result.

Should grease or oil come in contact with the disc drive plate

or friction wheel be sure to clean plate and wheel thoroughly

with a alcohol base solvent.

LUBRICATION - EVERY 10 HOURS

1. Auger Shaft- Using a hand grease gun, lubricate the

auger shaft zerk fittings (A) every ten (10) operating

hours. Each time a shear bolt is replaced, the auger shaft

MUST be greased (Figure 22). (See To Replace Auger

Shear Bolt in the Repair/Adjustment section).

2. For storage or when replacing shear bolts, remove shear

bolts and lubricate auger shaft zerks. Rotate augers sev-

eral times on the shaft and reinstall the shear bolts.

F_01160J 20

La page charge ...

Craftsman C950-52021-0 Le manuel du propriétaire

Craftsman C950-52021-0 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents