Simplicity SEARS CRAFTSMAN SNOWTHROWER, 13.5 TP, 27 INCH Manuel utilisateur

1738165

Revision A

Rev. Date 07/2009

Sears Canada Inc., Toronto, Ontario M5B 2C3

Visit our Craftsman website: www.sears.ca/craftsman

Owner’s

Manual

Model

C950-52943-0

13.5 T.P. 27 inch

CAUTION:

You must read and

understand this owner’s

manual before operating

unit.

Serial No. ______________

DUAL STAGE

SNOW THROWER

Not for

Reproduction

2

Thank you for purchasing this quality-built Craftsman snow thrower. We’re pleased that you’ve placed your confidence in the Craftsman

brand. When operated and maintained according to the instructions in this manual, your Craftsman product will provide many years of

dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with snow throwers and how to avoid

them. This snow thrower is designed and intended only for snow throwing and is not intended for any other purpose. It is important that

you read and understand these instructions throroughly before attempting to start or operate this equipment. This snow thrower

requires final assembly before use. Refer to the Assembly section for instructions on final assembly procedures. Follow the instruc-

tions completely. Save these instructions for future reference.

Snow Thrower:

Model Number ______________________________

Revision _____

Serial Number ______________________________

Engine:

Model Number ______________________________

Revision _____

Serial Number ______________________________

Date Purchased: ______________________________

Store Where Purchased: ______________________________

City: ______________________________

Province: ______________________________

Telephone: ______________________________

NOTICE: Record this information about your snow thrower so that you will be able to provide it in case of loss or theft.

Not for

Reproduction

OPERATOR SAFETY.................................................................................... 4

ASSEMBLY .............................................................................................. 10

TOOLS REQUIRED FOR ASSEMBLY.......................................................................................................... 10

CONTENTS OF SHIPPING CARTON.......................................................................................................... 10

PARTS BAG CONTENTS............................................................................................................................ 10

UNPACKING.............................................................................................................................................. 11

UPPER HANDLE AND CRANK ASSEMBLY................................................................................................ 12

CHECK THE CABLES................................................................................................................................ 12

SET THE LENGTH OF THE CABLES.......................................................................................................... 12

SPEED SELECT LEVER ASSEMBLY .......................................................................................................... 13

SNOW CHUTE ASSEMBLY........................................................................................................................ 14

HEADLIGHT ASSEMBLY ........................................................................................................................... 14

FEATURES AND CONTROLS .......................................................................... 15

OPERATION ............................................................................................. 17

BEFORE OPERATING SNOW THROWER................................................................................. 17

OPERATE THE SNOW THROWER.............................................................................................................. 17

STOP THE SNOW THROWER.................................................................................................................... 18

TRACTION LOCK PINS ............................................................................................................................. 18

CHECK THE OIL (BEFORE STARTING ENGINE) ........................................................................................ 18

FILL THE FUEL TANK................................................................................................................................ 19

START THE ENGINE.................................................................................................................................. 19

STOP THE ENGINE.................................................................................................................................... 20

CLEAR A CLOGGED DISCHARGE CHUTE.................................................................................................21

OPERATING TIPS...................................................................................................................................... 21

MAINTENANCE ......................................................................................... 22

SERVICE RECOMMENDATIONS ............................................................................................................... 22

LUBRICATE AUGER GEAR BOX................................................................................................................. 23

LUBRICATE AUGER SHAFT FITTINGS ...................................................................................................... 23

LUBRICATE CHUTE ROTATION GEAR....................................................................................................... 23

ENGINE MAINTENANCE ........................................................................................................................... 24

CHANGE THE SPARK PLUG...................................................................................................................... 25

ADJUST SKID HEIGHT.............................................................................................................................. 26

BELT ADJUSTMENT.................................................................................................................................. 27

BELT GUIDE ADJUSTMENT ...................................................................................................................... 28

CHECK AND ADJUST THE CABLES.......................................................................................................... 28

AUGER SHEAR PIN REPLACEMENT......................................................................................................... 30

CHECK THE TIRES .................................................................................................................. 30

STORAGE................................................................................................ 31

OFF SEASON STORAGE............................................................................................................................ 31

LUBRICATE HEX SHAFT AND CHAINS..................................................................................................... 31

REMOVE FROM STORAGE........................................................................................................................ 31

TROUBLESHOOTING................................................................................... 32

WARRANTIES........................................................................................... 34

SPECIFICATIONS ....................................................................................... 37

3

TABLE OF CONTENTS

Not for

Reproduction

4

OPERATOR SAFETY

The safety alert symbol and signal word (DANGER,

WARNING, CAUTION, or NOTICE) is used to indicate the likeli-

hood and potential severity of personal injury and/or damage to

the product. In addition, a hazard symbol may be used to

represent the type of hazard.

Safety Alert Symbol and Signal Words

DANGER indicates a hazard which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazard which, if not avoided, could

result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, could

result in minor or moderate injury.

NOTICE indicates a situation that could result in damage

to the

product

.

DANGER - Amputation Hazard

The discharge chute contains a rotating

impeller to throw snow. Never clear or unclog

the discharge chute with your hands. Fingers

can quickly become caught and traumatic

amputation or severe laceration will result.

Always use a clean-out tool to clear or unclog

the discharge chute.

Safety Alert – Identifies safety information about

hazards that can result in personal injury.

Operator’s Manual – Read and understand before

performing any activity or running snowthrower.

Rotating Impeller Keep a Safe

Distance from

Snowthrower

Rotating Auger Rotating Gears

Never Reach into

Rotating Parts Thrown Objects

Fire Explosion

Shock Toxic Fumes

Hot Surface Recommended

Ear Protection for

Extended Use

Shut off engine and remove spark plug connector

before performing maintenance or repair work.

Hazard Symbols and Meanings

DANGER

• Hand contact with the rotating impeller inside the discharge

chute is the most common cause of injury associated with

snowthrowers.

• This snowthrower is capable of amputating hands and feet,

and throwing objects. Read and observe all the safety

instructions in this manual. Failure to do so will result in

death or serious injury.

WARNING

U.S.A. Models: Certain components in this product and its

related accessories contain chemicals known to the state of

of California to cause cancer, birth defects, or other repro-

ductive harm. Wash hands after handling.

WARNING

U.S.A. Models: The engine exhaust from this product con-

tains chemicals known to the State of California to cause

cancer, birth defects, or other reproductive harm.

WARNING

U.S.A. Models: Battery posts, terminals, and related acces-

sories contain lead and lead components - chemicals known

to the State of California to cause cancer and reproductive

harm. Wash hands after handling.

Certification: This equipment meets the requirements of ANSI

B71.3-2005 for snowthrowers.

Not for

Reproduction

5

OPERATOR SAFETY

Oil

Fuel Forward

On Off Neutral

Choke Off Reverse

Choke On

Stop Electric Start -

Engage (Down) &

Disengage (Up)

Slow Engine - Run

Fast STOP Engine - Stop

Traction Control -

Engage (Down) Auger Control -

Engage (Down)

Auger Clutch Chute Deflector

(Up and Down)

Discharge Chute

(Left and Right) Heated Hand Grips

(High and Low)

Control Symbols on Equipment

12

F

Free-HandTM Control

Easy-TurnTM Traction Control

• Be thoroughly familiar with the controls and the proper use of the snow

thrower.

• Make sure you are properly trained before operating the snowthrower.

•Know how to stop the unit and disengage the controls quickly.

• Never allow anyone to operate the snowthrower without proper instruction.

• Always follow the instructions in the operator’s manual, if the snowthrower

will be stored for an extende d period.

• Maintain or replace safety and instruction labels as necessary.

• Never attempt to make major repairs on the snowthrower unless you have

been properly trained. Improper servicing of the snowthrower can result

in hazardous operation, equipment damage, and voiding of the product

warranty.

DANGER

Read, understand, and follow all the instructions on the

snowthrower and in the operator’s manual before operating

this unit.

Failure to observe the safet y instructions in this manual will

result in death or serious injury.

Read the Manual

TO SAFELY CLEAR A CLOGGED DISCHARGE CHUTE

DANGER: Hand contact with the rotating impeller inside the discharge

chute is the most common cause of injury associated with snow

throwers. Never use your hands to clean out the discharge chute.

FOLLOW THESE INSTRUCTIONS:

1. Shut OFF the engine.

2. Wait 10 seconds to be sure the impeller blades have stopped rotating.

3. Always use a clean-out tool, not your hands.

DANGER

Discharge chute contains rotating impeller to throw snow.

Never clear or unclog the discharge chute with your hands.

Fingers can quickly become caught in the impeller. Always

use a clean-out tool.

Failure to observe these safety instructions will result in

traumatic amputation or severe laceration.

Discharge Chute

NOTE: Not all control symbols shown on this page will appear

on your snowthrower. See FEATURES AND CONTROLS section

for the applicable symbols.

Not for

Reproduction

6

WHEN ADDING FUEL

• Turn off engine and let cool at least 2 minutes before removing the fuel

cap and adding fuel.

• Fill fuel tank outdoors or in a well ventilated area.

• Do not overfill the fuel tank. To allow for the expansion of gasoline, do not fill

above the bottom of the fuel tank neck.

• Keep fuel away from sparks, open flames, pilot lights, heat, and other

ignition sources.

• Check fuel lines, cap, and fittings frequently for cracks or leaks. Replace if

necessary.

• Use an approved fuel container.

• If fuel spills, wait until it evaporates before starting engine.

WHEN STARTING ENGINE

• Ensure that spark plug, muffler, fuel cap, and air cleaner (if equipped) are in

place and secured.

• Do not crank the engine with the spark plug removed.

• If fuel is spilled, do not attempt to start the engine, but move the snow

thrower away from the area of the spill, and avoid creating any source of

ignition, until the fuel vapors have dissipated.

• Do not over-prime the engine. Follow the engine starting instructions in this

manual.

• If the engine floods, set choke (if equipped) to OPEN/RUN position, move

throttle (if equipped) to FAST position and crank until engine starts.

WHEN OPERATING EQUIPMENT

• Do not tip the snowthrower at an angle which causes the fuel to spill.

• Do not choke the carburetor to stop the engine.

• Never run the engine with the air cleaner assembly (if equipped) or the air

filter (if equipped) removed.

WHEN CHANGING OIL

• If you drain the oil from the top oil fill tube, the fuel tank must be empty or

fuel can leak out and result in a fire or explosion.

WHEN TRANSPORTING EQUIPMENT

• Transport with fuel tank EMPTY, or with fuel shut-off valve OFF.

WHEN STORING GASOLINE OR EQUIPMENT WITH FUEL IN TANK

• Store away from furnaces, stoves, water heaters, or other appliances that have

pilot light or other ignition source because they can ignite fuel vapors.

DANGER

Fuel and its vapors are extremely flammable and explosive.

Always handle fuel with extreme care.

Failure to observe these safety instructions can cause a fire

or explosion which will result in severe burns or death.

Fuel Handling

• Keep the area of operation clear of all persons, particularly small children

and pets.

• Thoroughly inspect the area where the snowthrower will be used and remove

all doormats, sleds, boards, wires, and other foreign objects.

• Do not operate the snowthrower without wearing adequate winter clothing.

• Wear footwear that will improve footing on slippery surfaces.

• Use caution to avoid slipping or falling especially when operating the

snowthrower in reverse.

• Never operate the snowthrower without good visibility or light. Always be

sure of your footing, and keep a firm hold on the handles.

• Do not clear snow across the face of slopes. Use extreme caution when

changing direction on slopes. Do not attempt to clear steep slopes.

• Do not overload the machine capacity by attempting to clear snow too

quickly.

• Never operate the snowthrower at high transport speeds on slippery

surfaces. Look behind the snowthrower and use care when operating in

reverse.

• Do not use the snowthrower on surfaces above ground level such as roofs of

residences, garages, porches, or other such structures or buildings.

• Operators should evaluate their ability to operate the snowthrower safely

enough to protect themselves and others from injury.

• The snowthrower is intended to remove snow only. Do not use the snow

thrower for any other purpose.

• Do not carry passengers.

• After striking a foreign object, shut OFF the engine, disconnect the cord on

electric motors, thoroughly inspect the snowthrower for any damage, and

repair the damage before restarting and operating the snowthrower.

• If the snowthrower vibrates abnormally, shut OFF the engine. Vibration is

generally a warning of trouble. See an authorized dealer if necessary for

repairs.

• For models equipped with electric starting motors, disconnect the power

cord after the engine starts.

DANGER

This snowthrower is only as safe as the operator. If it is

misused, or not properly maintained, it can be dangerous.

Remember you are responsible for your safety and that of

those around you.

Operation and Equipment Safety

OPERATOR SAFETY

Not for

Reproduction

7

• Keep children out of the area during operation. Children are often attracted to

the equipment. Be mindful of all persons present.

• Be alert and turn unit off if children enter the area.

• Never allow children to operate the unit.

• Use extra care when approaching blind corners, shrubs, trees, or other

objects that may obscure vision. Children may be present.

DANGER

Tragic accidents can occur if the operator is not alert to the

presence of children. Children are often attracted to the unit

and the operating activity. Never assume that children will

remain where you last saw them.

Children

• Start and run engine outdoors.

• Do not run the engine in an enclosed area, even if doors or windows are

open.

DANGER

Engines give off carbon monoxide, an odorless, colorless,

poison gas.

Breathing carbon monoxide can cause nausea, fainting,

or death.

Engine Safety

• Disengage all clutches and shift into neutral before starting the engine.

• Let the engine adjust to outdoor temperatures before starting to clear snow.

• Use a grounded three-wire plug-in for all snowthrowers equipped with

electric drive motors or electric starting motors.

DANGER

Safe operation of the snowthrower requires the proper care

and maintenance of the engine. Failure to observe the safety

instructions in this manual will result in death or serious

injury.

• Always wear safety glasses or eye shields while during operation, and while

performing an adjustment or repair.

• Always be aware of the direction the snow is being thrown. Nearby

pedestrians, pets, or property may be harmed by objects being thrown.

• Be aware of your environment while operating the snowthrower. Running

over items such as, gravel, doormats, newspapers, toys, and rocks hidden

under snow, can all be thrown from the chute or jam in the auger.

• Use extreme caution when operating on or crossing gravel drives, walks, or

roads.

• Adjust the collector housing height to clear gravel or crushed rock surface.

• Never operate the snowthrower near glass enclosures, automobiles, window

wells, drop-offs, and the like without proper adjustment of the discharge

chute angle.

• Familiarize yourself with the area in which you plan to operate the snow

thrower. Mark off boundaries of walkways and driveways.

DANGER

Objects can be picked up by auger and thrown from chute.

Never discharge snow toward bystanders or allow anyone in

front of the snowthrower. Failure to observe these safety

instructions will result in death or serious injury.

Thrown Objects

• Whenever cleaning, repairing, or inspecting the snowthrower, make sure the

engine is OFF, spark plug wire is disconnected, and all moving parts have

stopped.

• Do not put hands or feet near or under rotating parts. Keep clear of the

discharge opening at all times.

• Never operate the snowthrower without proper guards, and other safety

devices in place and working.

• Never leave the snowthrower unattended while engine is running. Always

disengage the auger and traction controls, stop engine, and remove keys.

• Keep all loose clothing away from the front of the snowthrower and auger.

Scarves, mittens, dangling drawstrings, loose clothes, and pants can quickly

become caught in the rotating device and amputation will occur. Tie up

long hair and remove jewelry.

• Run the machine a few minutes after discharging snow to prevent freeze-up

of the collector/impeller.

• Disengage power to the collector/impeller when snowthrower is transported

or not in use.

DANGER

Keep hands, feet, and clothing away from rotating parts.

Rotating parts can contact or entangle hands, feet, hair,

clothing, or accessories.

Failure to observe these safety instructions will result in

traumatic amputation or severe laceration.

Moving Parts

OPERATOR SAFETY

Not for

Reproduction

8

• When performing any maintenance or repairs on the snowthrower, shut OFF

the engine, disconnect spark plug wire, and keep the wire away from the

plug to prevent someone from accidently starting the engine.

• Check shear bolts and other hardware at frequent intervals for proper

tightness to be sure the snowthrower is in safe working condition.

• Keep nuts and bolts tight and keep snowthrower in good condition.

• Never tamper with safety devices. Check their proper operation regularly and

make necessary repairs if they are not functioning properly.

• Components are subject to wear, damage, and deterioration. Frequently

check components and replace with recommended parts, when necessary.

• Check control operation frequently. Adjust and service as required.

• Use only factory authorized replacement parts when making repairs.

• Always comply with factory specifications on all settings and adjustments.

• Only authorized service locations should be utilized for major service and

repair requirements.

• Use only attachments and accessories approved by the factory (such as

wheel weights, counterweights, or cabs).

• Never attempt to make any adjustments while the engine is running (except

when specifically recommended by the factory).

• Do not allow grease or oil to contact the rubber friction wheel or the disc

drive plate. If the disc drive plate or friction wheel come in contact with

grease or oil, damage to the rubber friction wheel will result.

WARNING

This snowthrower must be properly maintained to ensure safe

operation and performance. Failure to observe the safety

instructions in this manual could result in death or serious

injury.

Maintenance and Storage

-

• If there is natural or LP gas leakage in area, do not start engine.

• Do not use pressurized starting fluids because vapors are flammable.

WARNING

Starting engine creates sparking.

Sparking can ignite nearby flammable gases.

Explosion and fire could result.

• Never touch a hot engine or muffler. Allow muffler, engine cylinder, and fins

to cool before touching.

• Remove debris from muffler area and cylinder area.

• Install and maintain in working order a spark arrester before using equipment

on forest-covered, grass-covered, or brush-covered unimproved land.

•U

U.S.A. Models:

It is a violation of California Public Resource Code

Section 4442 to use or operate the engine on or near any forest-covered,

brush-covered, or grass-covered land unless the exhaust system is equipped

with a spark arrester meeting any applicable local or state laws. Other states

or federal areas may have similar laws.

WARNING

Running the engine produces heat. Engine parts, especially

muffler, become extremely hot.

Failure to observe these safety instructions could result in

severe thermal burns on contact.

Engine Safety (Continued)

OPERATOR SAFETY

Not for

Reproduction

9

Safety Decals Figure 1

Part No. 1737865

Chute Danger Decal

Part No. 1737872

Shift Decal

Part No. 1737866

Auger Danger Decal

Product ID Number &

Serial Number Decal

(Rear of Motor Box)

Engine Decals

THIS ENGINE MEETS 2008 CA EXH AND EPA

PHASE 2 EMISSION REGULATIONS FOR SMALL

OFF-ROAD ENGINES. REFER TO OWNER'S

MANUAL FOR MAINTENANCE SPECIFICATIONS,

ADJUSTMENTS, AND EMISSIONS

DURABILITY INFORMATION.

EPA EMISSIONS COMPLIANCE PERIOD: CATEGORY: X

CA COMPLIANCE PERIOD: X

DISP: XXXcc e11*97/68SA*XXXX/XX*XXXX*XX

FAMILY XXXXX.XXXXXX XXXXXX

IMPORTANT ENGINE INFORMATION

BRIGGS & STRATTON CORPORATION

Part No. 278297

Part No. 277953

Part No. 1737869

Auger Control Decal

Part No. 1737870

Traction Control Decal

Look for this symbol to indicate important safety

pre cautions. This symbol indicates: “Attention! Become

Alert! Your Safety Is At Risk.”

WARNING:

If any safety decals become worn or damaged and

cannot be read, order replacement decals from your local dealer.

OPERATOR SAFETY

Before operating your snow thrower, read the safety decals

as shown on your snow thrower. The cautions and warnings

are for your safety. To avoid a personal injury or damage to

your snow thrower, understand and follow all the safety decals.

Not for

Reproduction

10

ASSEMBLY

TOOLS REQUIRED FOR ASSEMBLY

1 – Knife

2 – 1/2" wrenches (or adjustable wrenches)

2 – 9/16" wrenches (or adjustable wrenches)

2 – 3/4" wrenches (or adjustable wrenches)

1 – 3/8" wrenches (or adjustable wrenches)

1 – Pair pliers or screw driver

CONTENTS OF SHIPPING CARTON

1 – Snow Thrower

1 – Container of Fuel Stabilizer (Located in Parts Bag)

1 – Snow Chute Assembly

1 – Crank Assembly

1 – Parts Bag

WARNING: Always wear safety glasses or eye shields

while assembling snow thrower.

PARTS BAG CONTENTS

1 -- Shifter Knob

(not actual size)

* 2 -- Wrenches

* 2--1/4--20 x 1.75 * 2--Spacer *2--1/4--20

Hex nut

*

*Non Assembly parts and power cord can be found in the Parts Bag shipped

with the snow thrower. The parts can be stored in the tool box located on top

of the belt cover.

HOW TO MEASURE SCREW SIZE

LENGTH

DIAMETER

Not for

Reproduction

11

ASSEMBLY

NOTE: Reference to right and left hand side of the snowthrower is from the

operator’s position at the handle.

UNPACKING

1. Using knife, cut along the dotted lines around the top and bottom of

carton. Then remove carton material as shown in Figure 2.

2. Remove shear pins and cotter pins from parts bag and place in shear

bolt storage box.

3. Locate and remove the parts bag.

NOTE: Set the fuel stabilizer aside until adding gasoline to the fuel

tank. We recommend that fuel stabilizer be added to the fuel each time

the tank is filled.

4. Roll the snowthrower off the carton by pulling on the lower handle.

CAUTION: DO NOT back over cables.

5. Remove the packing material from the handle assembly.

6. Cut ties securing the clutch control cables to the lower handle.

NOTE: If the cables have become disconnected from the clutch levers,

reinstall the cables as shown in Figure 3.

Unpacking the Snowthrower Figure 2

Clutch Control Cables Figure 3

Not for

Reproduction

12

UPPER HANDLE AND CRANK ASSEMBLY

1. Loosen, but do not remove the screws, flatwashers, lockwashers, and

hex nuts in the upper holes of the lower handle (see Figure 4).

2. Remove the fasteners and the crank assembly eyebolt from the lower

holes of the lower handle.

3. Raise upper handle into operating position. Upper handle should be to

the outside of the lower handle.

NOTE: Make sure the cables are not caught between the upper and

lower handle.

4. Install the fasteners and the crank assembly eyebolt that were removed

in step 2. DO NOT tighten until all fasteners are in place.

5. Attach the crank rod (A

A

, Figure 5) to the universal joint assembly (B

B

)

with the hair pin (C

C

).

6. Tighten nut on eye bolt. Make sure eye bolt is properly aligned and the

crank can freely rotate (see Figure 4).

7. Tighten all handle bolts.

NOTE: Make sure crank does not touch carburetor cover.

Crank

Eye Bolt

Adaptor Boot

Flatwasher

Nut

Flatwasher

Bolt

Lockwasher

Flatwasher

Locknut

Upper Handle Assembly Figure 4

Crank Assembly Figure 5

CHECK THE CABLES

1. If control cables have become unattached from motor mount frame, re-

connect cables as shown in Figure 6.

2. For cable adjustments, see “Check and Adjust the Cables” in the

MAINTENANCE section.

SET THE LENGTH OF THE CABLES

The traction drive and auger drive cables (A

A

and B

B,

Figure 6) were adjusted

at the factory and no adjustments should be necessary. However, after the

handles are put in the operating position, the cables can be too tight or too

loose. If an adjustment is necessary, see “Check and Adjust the Cables” in

the MAINTENANCE section.

Check the Cables Figure 6

ASSEMBLY

AB

C

BA

Not for

Reproduction

13

SPEED SELECT LEVER ASSEMBLY

1. Cut plastic tie (A

A

, Figure 7) securing speed select lever assembly (B

B

)

to the shifter bracket (C

C

).

2. Remove locknut (A

A

, Figure 8), washer (B

B

), spring (C

C

), and bolt (D

D

).

NOTE: View is from right side of unit standing in operator’s position.

3. Position speed selector lever assembly as shown in Figure 9.

4. Reinstall bolt (D

D,

Figure 8), spring (C

C

), washer (B

B

) and locknut (A

A

).

5. Tighten locknut until 1/8 to 3/16 inch of the bolt threads protrude past

the locknut.

6. Thread the 3/8-16” hex jam nut (E

E

) onto the lever (F

F

) until the nut

reaches the end of the thread.

7. Thread the plastic knob (G

G

) as far as possible and ensure that the knob

points forward.

8. Tighten the 3/8-16” hex jam nut against the knob securely.

9. Move shifter through all speeds to ensure proper tension of the spring.

If shifter lever sticks in any of the notches, loosen locknut 1/2 turn at a

time until shifter lever moves more freely.

Control Panel and Shifter Bracket Figure 9

Control Panel

Shifter Bracket

Shift Lever and Bracket Figure 7

Shifter Handle Figure 8

ASSEMBLY

C

A

B

A B

C

1/8 to 3/8 inch of

exposted thread

D

G

E

F

Not for

Reproduction

14

SNOW CHUTE ASSEMBLY

NOTE: The chute ring assembly (A, Figure 10) comes installed on the unit

from the factory.

1. Turn crank assembly (Figure 4) until the arrow on outer ring (B

B

, Figure

10) of chute ring assembly points forward.

NOTE: Make sure the slot in the chute ring aligns with the arrow on the

outer ring.

2. Install chute deflector (C

C

) using four screws (D

D

) and nuts (E

E

) in holes

as shown. The chute deflector must point forward for proper installa-

tion.

3. Tighten screws snugly but be careful not to over-tighten.

Snow Chute Assembly Figure 10

HEADLIGHT ASSEMBLY

The headlight is mounted on the right side of the upper handle. It is in-

stalled upside-down for shipping purposes.

1. Remove the nut (A

A

, Figure 11) and lockwasher (B

B

) from the carriage

bolt (C

C

).

2. Turn the headlight (D

D

) to the top side of the upper handle (E

E

). Ensure

external tooth lockwasher (F

F

) and saddle washer (G

G

) are in place as

shown in Figure 11.

3. Install the nut and lockwasher to secure the headlight to the handle.

The headlight should point toward the snow clearing path.

Headlight Assembly Figure 11

ASSEMBLY

C

A

B

D

E

D

C

E

G

F

B

A

Not for

Reproduction

15

Snow Thrower Controls Figure 12

SNOW THROWER CONTROLS

A. Speed Select Lever — Allows the operator to use one of six (6)

forward and two (2) reverse speeds (see Figure 12). To shift, move

speed select lever to desired position.

NOTICE: Do not move speed select lever while Traction

Drive Clutch is engaged. This may result in severe damage

to drive system.

B. Auger Drive Clutch Lever — Used to engage and disengage the

auger and impeller. To engage push down, to disengage release.

C. Traction Drive Clutch Lever — Used to propel snow thrower for-

ward or reverse. Push down to engage, release to disengage.

D. Chute Rotation Crank — Used to change direction of the snow

discharge. Turn handle clockwise to turn chute to right. Turn handle

counterclockwise to turn chute to left.

E. Chute Deflector Wing Nut — Used to control the angle of the

chute deflector (up or down).

F. Clean-Out Tool — Used to remove snow and debris from the dis-

charge chute and the auger housing.

G. Skid Shoe — Used to adjust ground clearance of auger housing.

H. Headlight — Used to operate the snow thrower in poor lighting

conditions.

I. Toolbox — Spare shear pins, shear bolt wrenches and spacers are

located in toolbox.

G

FEATURES AND CONTROLS

B

C

D

A

F

SNOW THROWER AND ENGINE CONTROLS

E

H

I

Not for

Reproduction

FEATURES AND CONTROLS

16

ENGINE CONTROLS

A. Choke Control Knob — Used to start a cold engine (see Figure

13).

B. Electric Start Button — Used to start the engine using the electric

starter.

C. Primer Button — Used to inject fuel directly into the carburetor

manifold to ensure fast starts in cool weather.

D. Safety Key — Must be inserted to start engine. Pull out to stop. Do

not turn safety key.

Engine Controls Figure 13

E. Starter Cord Handle — Used to start the engine manually.

F. ON/OFF Switch — Used to start and stop the engine.

G. Fuel Tank and Cap — Fill the fuel tank to approximately 1-1/2 in.

(38 mm) below the top of the neck to allow for fuel expansion.

H . Oil Fill Cap (Extended Dipstick)

C

H

A

F

E

B

G

STOP

D

Not for

Reproduction

17

BEFORE OPERATING SNOW THROWER

■

Check the fasteners. Make sure all fasteners are tight.

■

Read this OPERATOR’S MANUAL and OPERATOR SAFETY before

operating your snow thrower. Compare the illustrations with your

SNOW THROWER to familiarize yourself with the location of var-

ious controls and adjustments. Save this manual for future refer-

ence.

NOTE: This snow thrower was shipped WITH OIL in the

engine. See “Before Starting Engine” instructions in the

OPERATION section of this manual before starting engine.

OPERATION

OPERATE THE SNOW THROWER

The most effective use of the snow thrower will be established by experi-

ence, taking into consideration the terrain, wind conditions, and building

location which will determine the direction of the discharge chute.

NOTICE: Do not throw snow toward a building as hidden objects

could be thrown with sufficient force to cause damage.

1. Start the engine. See “To Start Engine” in this section.

2. Rotate the crank (A

A

, Figure 12) to set the direction (left or right) of the

discharge chute.

3. Adjust the snow chute deflector. Loosen the wing nut (A

A

, Figure 14) on

the side of the snow chute and raise the chute deflector for more

distance, or lower it for less distance. Then tighten the wing nut.

Adjust Chute Deflector Figure 14

A

WARNING: The operation of any snow thrower can result in foreign objects being thrown into the eyes, which can result in

severe eye damage. Always wear safety glasses or eye shields before beginning snow thrower operation. We recommend

standard safety glasses or Wide Vision Safety Mask over spectacles.

CAUTION: Before operating, make sure the area in front

of the snow thrower is clear of bystanders or obstacles.

NOTE: Always release the traction control lever before moving

the speed select lever.

4. Use the speed select lever (A

A

, Figure 12) to select the forward drive

speed. Set the speed select lever to one of the following positions as

determined by snow conditions:

1-2 Wet, Heavy, Slushy, Extra Deep

3 Moderate

4-5 Very Light

6 Transport

NOTE: When clearing wet, heavy, snow, it is recommended that

the ground speed of the unit be reduced, maintain full throttle,

and do not attempt to clear the full width of the unit.

5. Engage the auger drive clutch lever (A

A

, Figure 15).

DOWN Engage Position

UP Disengage Position

6. Engage the traction drive clutch lever (B

B

). As the snow thrower starts

to move, maintain a firm hold on the handles and guide the snow

thrower along the cutting path. Do not attempt to push the snow

thrower.

7. To stop forward motion, release the traction drive clutch lever (B

B

).

Control Levers Figure 15

8. To stop the auger, release the auger drive clutch lever (A

A

).

9. To move the snow thrower backwards, move the speed select lever (A

A

, Fig-

ure 12) into first or second reverse (R1 or R2), and engage the traction drive

clutch lever (B

B

, Figure 15).

BA

WARNING: Never run engine indoors or in an enclosed,

poor ventilated area. Engine exhaust contains CARBON

MONOXIDE, an ODORLESS and DEADLY GAS.

• Keep hands, feet, hair, and loose clothing away from

any moving parts on engine and snow thrower.

• Temperature of muffler and nearby areas can exceed

150°F (66°C). Avoid these areas.

• DO NOT allow children or young teenagers to operate or

be near snow thrower while it is operating.

Not for

Reproduction

TRACTION LOCK PINS

The right traction wheel can be completely released using the locking pin

(A

A

, Figure 16). This allows the unit to be easily moved with the engine off.

Traction Lock Pins Figure 16

CHECK THE OIL (BEFORE STARTING ENGINE)

NOTE: The engine was shipped from the factory filled with oil.

Check the level of the oil. Add oil as needed.

1. Make sure the unit is level. Use a high quality detergent oil classified

“For Service SF, SH, SJ, SL, or higher”.

2. Remove the oil fill cap/dipstick (A

A

, Figure 17) and wipe with a clean cloth.

3. Insert the oil fill cap/dipstick and turn clockwise to tighten.

4. Remove the oil fill cap/dipstick and check the oil.

NOTE: Do not check the level of the oil while the engine runs.

5. If necessary, add oil until the oil reaches the FULL mark on the oil fill

cap/dipstick. Do not add too much oil.

6. Tighten the oil fill cap/dipstick securely each time you check the oil

level.

NOTE: For extreme cold operating conditions of 0°F (-18°C) and

below, use a synthetic 5W30 motor oil for easier starting.

NOTE: S.A.E. 5W30 motor oil may be used to make starting

easier in areas where the temperature is 20°F (-7°C) to 0°F

(-18°C). Synthetic 5W30 is acceptable for all temperatures.

DO NOT mix oil with gasoline. See Chart for oil recommenda-

tions.

FULL

Checking the Oil

Figure 17

A

18

OPERATION

STOP THE SNOW THROWER

1. Release the traction drive clutch lever (B

B

, Figure 15).

2. Push the ON/OFF switch (A

A

, Figure 22) to the OFF position and pull out the

safety key (B

B

).

WARNING: Read Operator’s Manual before operating

machine. This machine can be dangerous if used

carelessly.

• Never operate the snow thrower without all guards,covers,

shields in place.

• Never direct discharge towards windows or allow

bystanders near machine while engine is running.

• Stop the engine whenever leaving the operating

position.

• Disconnect spark plug before unclogging the impeller

housing or the discharge chute and before making

repairs or adjustments.

• When leaving the machine, remove the safety key. To

reduce the risk of fire, keep the machine clean and free

from spilled gas, oil, and debris.

* Below 40°F (4°C) the use of SAE 30 will result in hard starting.

** Above 80°F (27°C) the use of 10W-30 may cause increased oil consumption. Check

oil level more frequently.

Not for

Reproduction

19

Start the engine as follows:

1. Check the oil level. See the “Check/Add Oil” section in the ENGINE

MANUAL.

2. Make sure equipment drive controls are disengaged.

3. Push the ON /OFF switch (A

A

, Figure 18) to the ON position.

Starting Engine Figure 18

4. Insert the safety key (A

A

, Figure 19) into the safety key slot and push

fully in to the RUN position.

5. Turn the choke knob (B

B

) fully clockwise if engine is cold.

NOTE: Do not use the choke to start a warm engine.

6. Push the primer button (C

C)

two times.

NOTE: Do not use the primer to start a warm engine.

NOTE: Ensure that electric extension cord is removed from the

power receptacle.

FILL THE FUEL TANK

This engine is certified to operate on gasoline. Exhaust Emission Control

System: EM (Engine Modifications).

Fill the fuel tank with fresh, clean, unleaded regular, unleaded premium, or re-

formulated automotive gasoline with a minimum of 85 octane along with a

fuel stabilizer (follow instructions on fuel stabilizer package). D

DO NOT

use

leaded gasoline. We recommend that fuel stabilizer be added to the fuel

each time that gasoline is added to the fuel tank.

NOTE: Winter grade gasoline has higher volatility to improve

starting. Be certain container is clean and free from rust or

other foreign particles. Never use gasoline that may be stale

from long periods of storage in the container.

CAUTION: DO NOT use gasoline containing any

amount of alcohol as it can cause serious damage to

the engine or significantly reduce the performance.

START THE ENGINE

Be sure that engine oil is at FULL mark on the oil fill cap/dipstick. The snow

thrower engine is equipped with an A.C. electric starter and recoil starter. Before

starting the engine, be certain that you have read the following information.

If engine floods, set the choke to the OPEN/RUN position and crank until the en-

gine starts.

WARNING: The electric starter is equipped with a

three−wire power cord and plug designed to operate on AC

house hold current. The power cord must be properly

grounded at all times to avoid the possibility of electric

shock which can cause injury to the operator. Follow all

instructions carefully as set forth:

Make sure your house has a three−wire grounded system.

If you are not sure, ask a licensed electrician. If your house does

not have a three−wire grounded system, do not use this electric

starter under any condition.

If your house has a three−wire grounded system but a three-hole

receptacle is not available to connect the electric starter, have a

three−hole receptacle installed by a licensed electrician.

WARNING: To connect power cord, always connect the

power cord first to the switch box located on the

engine and then plug the other end into a three−hole

grounded receptacle.

WARNING: To disconnect the power cord, always

unplug the end connected to the three−hole grounded

receptacle first.

WARNING: Gasoline is flammable. Always use caution

when handling or storing gasoline. Turn engine off and

let engine cool at least two minutes before removing the gas

cap. Do not add gasoline to the fuel tank while snow thrower

is running, hot, or when snow thrower is in an enclosed area.

Keep away from open flame, electrical sparks and DO NOT

SMOKE while filling the fuel tank. Never fill the fuel tank

completely; but fill the fuel tank to within 1-1/2 inches (3.8

mm) from the top to provide space for the expansion of the

fuel. Always fill fuel tank outdoors and use a funnel or spout

to prevent spilling. Make sure to wipe up any spilled fuel

before starting the engine.

Store gasoline in a clean, approved container, and keep the

cap in place on the container. Keep gasoline in a cool well

ventilated place; never in the house. Never buy more than a

30 day supply of gasoline to assure volatility. Gasoline is

intended to be used as a fuel for internal combustion engines;

therefore, do not use gasoline for any other purpose. Since

many children like the smell of gasoline, keep it out of their

reach because the fumes are dangerous to inhale, as well as

being explosive.

A

OPERATION

Not for

Reproduction

20

Inserting Safety Key Figure 19

7. Rewind Start: Firmly hold the starter cord handle (A

A

, Figure 20). Pull

the starter cord handle slowly until resistance is felt, then pull rapidly.

WARNING: Rapid retraction of the starter cord (kickback)

will pull your hand and arm toward the engine faster

than you can let go. Broken bones, fractures, bruises,

or sprains could result. When starting engine, pull the

starter cord slowly until resistance is felt and then pull

rapidly to avoid kickback.

NOTE: If the engine does not start after three attempts, see the

Engine Manual Troubleshooting section.

8. Electric Start: First connect the extension cord to the power cord

receptacle and then into a wall receptacle. If additional extension cord is

required, make sure it is three-wire.

WARNING: If the extension cord is damaged, it must

be replaced by the manufacturer (or its service agent)

or a similarly qualified person to avoid a hazard.

Starting with Electric Start Figure 21

IMPORTANT: To extend the life of the starter, use short

starting cycles (five seconds maximum). Wait one minute

between starting cycles.

NOTE: If the engine does not start after three attempts, see the

Engine Manual Troubleshooting section.

Starting with Cord Handle Figure 20

A

B

C

A

B

STOP THE ENGINE

Before stopping the engine for a few minutes to help dry off any moisture

on the engine.

WARNING: Gasoline and vapors are extremely

flammable and explosive. Fire or explosion can

cause severe burns or death. DO NOT choke the

carburetor to stop the engine.

1. Push the ON/OFF switch (A

A

, Figure 22) to the OFF position.

2. Remove the safety key (B

B

). Keep the safety key out of the reach of

children.

Stopping Engine Figure 22

NOTE: Do not lose the safety key. Keep the safety key in a safe

place. The engine will not start without the safety/ignition key.

A

B

9. Electric Start: Depress the starter push button (A

A

, Figure 21). After you

start the engine, first disconnect the extension cord from the wall receptacle

and then from the power cord receptacle (B

B

).

A

OPERATION

Not for

Reproduction

La page charge ...

Simplicity SEARS CRAFTSMAN SNOWTHROWER, 13.5 TP, 27 INCH Manuel utilisateur

Simplicity SEARS CRAFTSMAN SNOWTHROWER, 13.5 TP, 27 INCH Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents