PowerSmart PSSW2260LED Manuel utilisateur

1

INSTRUCTION MANUAL

EN 26 inch Two Stage Gas Snow Thrower

FR 26 inch Souffleuse à Neige à Deux Phase

ES Quintanieves De Gas De 26 Pulgadas Con Dos Etapas

Model

Have product questions or need technical support? Please feel free to contact us!

Website: www.Amerisuninc.com

www.PowerSmartUSA.com

Toll free: 1-800-791-9458 Mon-Fri 9-5 EST

Email: support@amerisuninc.com

PSSW26LED/PSS2260L

PSS2260LED/PSSHD26-LED

Website

2

TABLE OF CONTENTS

Technical data ................................................................................................. 2

Introduction ..................................................................................................... 3

Safety information .......................................................................................... 3

Knowing your snow thrower .......................................................................... 7

Snow thrower preparation ............................................................................... 9

Operating your snow thrower ......................................................................... 11

Maintenance .................................................................................................... 13

Troubleshooting .............................................................................................. 14

Exploded view and parts list ........................................................................... 16

Two (2) years limited warranty ...................................................................... 26

TECHNICAL DATA

26 inch Two Stage Electric Start Snow Thrower

Model #: PSSW26LED/PSS2260L/PSS2260LED/PSSHD26-LED

Engine: 212cc Snow Engine

Engine oil Capacity: 16 fl.oz

Fuel Tank Capacity: 0.66 Gallon

Start System: 120V Electric / Recoil

Clearing Width: 26 in.

Clearing Height: 20 in.

Chute Rotation Angle: 180º

Speed: 6 Forward, 2 Reverse

Tire Size: 13 in.

Overall Dimensions: 31.1x26.3x22in.

Weight: 143 lbs

Thank you for purchasing PowerSmart products.

It is crucial and highly recommended that you read this instruction manual in its’ entirety, as this is an

invaluable tool and reference point in understanding the operation of your unit.

Please register your unit online at www. Amerisuninc.com. This process will allow us to track your

warranty information and update our records regarding your unit accordingly.

Important: Our Ccompany does not provide email or personal information to any third party for any reason.

For any questions check our website or call customer service at (800)791 9458.

EN

3

INTRODUCTION

Thank you for purchasing a PowerSmart® Product. This manual provides detailed information regarding

the safe operation and maintenance of this product. Every effort has been made to ensure the accuracy of

the information in this document. PowerSmart® reserves the right to change this product and

specifications at any time without prior notice.

Please keep this manual available to all users during the entire life of the product.

This manual contains special messages to bring attention to potential safety concerns, product

damage as well as helpful operating and servicing information. Please read all the

information carefully to avoid injury and machine damage.

QUESTIONS? PROBLEMS?

To answer questions and resolve issues in the most efficient and timely manner, please contact Customer

Service at (800) 791-9458, Mon-Fri 9am-5pm EST or email: [email protected].

NOTICE REGARDING EMISSIONS

Engines that are certified to comply with U.S. EPA emission regulations for SORE (Small Off Road

Equipment), are certified to operate on regular unleaded gasoline, and may include the following

emission control systems: (EM) Engine Modifications and (TWC) Three-Way Catalyst (if so equipped).

SAFETY INFORMATION

This symbol points out important safety instructions which, if not followed, could endanger

the personal safety and or property of yourself and others. Read and follow all instructions in

this manual before attempting to operate this machine. Failure to comply with these

instructions may result in personal injury.

WARNING! This machine was built to be operated according to the safe operation practices

in this manual. As with any type of power equipment, carelessness or error on the part of the

operator can result in serious injury. This machine is capable of amputating fingers, hands,

toes and feet and throwing foreign objects. Failure to observe the following safety instructions could

result in serious injury or even a fatal occurrence.

It is your responsibility to restrict the use of this power machine to persons who read, understand

and follow the warnings and instructions in this manual and on the machine.

ROTATING PARTS! Only use clean-out tool to clear blockages. NEVER use your

hands.

NEVER direct discharge towards persons or property that may be injured or damaged

by thrown objects.

Keep people away from unit while operating. Keep children out of work area and under

watchful care of a responsible adult.

4

TRAINING

Read, understand, and follow all instructions on the machine and in the manual(s) before attempting to

assemble and operate. Keep this manual in a safe place for future and regular reference.

• Be familiar with all controls and their proper operation. Know how to stop the machine and disengage

them quickly.

• Never allow children under 14 years of age to operate this machine. Children 14 and over should read

and understand the instructions and safe operation practices in this manual and on the machine and be

trained and supervised by an adult.

• Never allow “non-trained” adult personnel to operate this machine without proper instruction.

• Thrown objects can cause serious personal injury. Plan and map out your snow-throwing pattern to

avoid discharge of material toward roads, bystanders and the like.

• Keep bystanders, pets and children at least 75 feet from the machine while it is in operation. Stop

machine if anyone enters the area.

• Exercise caution to avoid slipping or falling, especially when operating in reverse.

PREPARATION

Thoroughly inspect the area where the equipment is to be used. Remove all doormats, newspapers, sleds,

boards, wires, branches and other foreign objects, which could be hazardous and damage the auger system.

• Always wear safety glasses or eye shields during operation and while performing an adjustment or

repair to protect your eyes, as thrown objects can ricochet and cause serious injury to the eyes.

• Do not operate without wearing adequate, winter outer garments. Do not wear jewelry, long scarves

or other loose clothing, which could become entangled in moving parts, and wear footwear that will

improve footing on slippery surfaces.

• Use a grounded “three-wire” extension cord and receptacle for all machines with electric start engines.

• Adjust skid shoe and/or housing height to clear gravel or crushed rock surfaces.

• Disengage all control levers before starting the engine.

• Never attempt to make any adjustments while engine is running, except where specifically

recommended in the instruction manual.

• Let engine and machine adjust to outdoor temperature before starting to clear snow.

PERSONAL SAFETY

• Engine exhaust, and certain vehicle components contain or emit chemicals known to cause cancer,

birth defects or other reproductive harm.

• Read, understand and follow all instructions on your snow thrower unit and in this instruction manual

before attempting to assemble and operate your machine.

• Keep this instruction manual in a safe place for future and regular reference. If replacement parts are

needed, refer to the Panel, Chute, Frame and Housing Diagrams and Parts’ Listings on pages 25-30.

• Stay alert, watch what you are doing and use common sense when operating your snow thrower unit.

• Do not use your snow thrower unit while you are tired or under the influence of drugs, alcohol,

medication. A moment of inattention while operating the snow thrower may result in severe bodily

injury.

•

NEVER LEAVE YOUR RUNNING SNOW THROWER UNATTENDED. Stop the engine!

• Do not leave your snow thrower unit until it has come to a complete stop.

• When stepping backwards, be cautious about any obstacles beneath your feet or behind you avoid

falling.

SERVICE

• Stop the engine before making any adjustments. Check for misalignment, breakage or binding of

moving parts, and any other conditions that may affect operation.

• If damaged, have the snow thrower unit serviced by an authorized service center using only specified,

manufactured replacement parts. This will ensure that the safety of the snow thrower unit is

maintained.

5

SAFE HANDLING OF GASOLINE

To avoid personal injury or property damage use extreme care in handling gasoline. Gasoline is extremely

flammable and the vapors are explosive. Serious personal injury can occur when gasoline is spilled on

yourself or your clothes which can ignite, therefore wash your skin and change clothes immediately.

• Use only an approved gasoline container.

• Extinguish all cigarettes, cigars, pipes and other sources of ignition.

• Never fuel snow thrower unit’s engine indoors.

• Never remove gas cap or add fuel while the engine is hot or running.

• Allow engine to cool at least two minutes before refueling.

• Never over fill fuel tank.

• Replace gasoline cap and tighten securely.

• If gasoline is spilled, wipe it off the engine and equipment. Move machine to another area. Wait 5

minutes before starting the engine.

• Never store the machine or fuel container inside where there is an open flame, spark or pilot light (e.g.

furnace, water heats, space heater, clothes dryer etc.).

• Allow machine to cool at least 5 minutes before storing.

• Never fill containers inside a vehicle or on a truck or trailer bed with a plastic liner. Always place

containers on the ground away from your vehicle before filling.

• If possible, remove gas-powered equipment from the truck or trailer and refuel it on the ground.

• If this is not possible, then refuel such equipment on a trailer with a portable container, rather than

from a gasoline dispenser nozzle.

• Keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling

is complete. Do not use a nozzle lock open device.

OPERATION

• Do not put hands or feet near rotating parts, in the auger impeller housing or chute assembly. Contact

with the rotating parts can amputate hands and feet.

• The auger (impeller) control lever is a safety device. Never bypass its operation. Doing so makes the

machine unsafe and may cause personal injury.

• The control levers must operate easily in both directions and automatically return to the disengaged

(vertical) position when released.

• Never operate with a missing or damaged chute assembly. Keep all safety devices in place and

working.

• Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon monoxide,

an odorless and deadly gas.

• Do not operate machine while under the influence of alcohol or drugs.

• Muffler and engine become hot and can cause burning. Do not touch. Keep children away.

• Exercise extreme caution when operating on or crossing gravel surfaces. Stay alert for hidden hazards

or traffic.

• Exercise caution when changing direction and while operating on slopes.

• Plan your snow-throwing pattern to avoid snow discharge towards windows, walls, cars etc., thus

avoiding possible property damage or personal injury caused by a ricocheting debris.

• Never direct discharge at children, bystanders and pets or allow anyone in front of the machine.

•

Do not overload machine capacity by attempting to clear snow at too fast of a rate….

Remember! Slow and steady operation is best to avoid clogs of snow being impelled too

rapidly.

• Never operate this machine without good visibility or light. Always be sure of your footing and keep

a firm hold on the handles. Walk, never run.

• Disengage power to the auger system (auger/impeller) by releasing the auger control (lever) when

transporting or not in use.

• Never operate machine at high transport speeds on slippery surfaces. Look down and behind and use

care when backing up.

6

• If the machine should start to vibrate abnormally, stop the engine, disconnect the spark plug wire and

ground it against the engine. Inspect thoroughly for damage. Repair any damage before starting and

operating.

• Disengage all (drive and auger) control levers and stop engine before you leave the operation position

(behind the handles).

• Wait until the auger /impeller comes to a complete stop before unclogging the chute assembly,

making any adjustments or inspections.

• Never put your hand in the discharge or collector openings. Always use the clean-out tool provided to

unclog the discharge opening. Do not unclog chute assembly while engine is running. Shut off engine

and remain behind handles until all moving parts have stopped before unclogging.

• Use only attachments and accessories approved by the manufacturer (e.g. wheel weights, tire chains,

cabs etc.).

• When staring engine, pull cord slowly until resistance is felt, then pull rapidly, Rapid retraction of

starter cord (kickback) will pull hand and arm toward engine faster then you can let go. Broken bones,

fractures, bruises or sprains could result.

• If situations occur which are not covered in this manual, use care and good judgment contact

customer support for assistance.

MAINTENANCE & STORAGE

• Never tamper with safety devices. Check their proper operation regularly. Refer to the maintenance

and adjustment sections of manual.

• Before cleaning, repairing, or inspecting machine disengage all control levers and stop the engine.

• Wait until the auger impeller comes to a complete stop. Disconnect the spark plug wire to prevent

unintended starting.

•

Check bolts and screws for proper tightness (EVERYTIME before & after use) as engine vibration

could cause hardware to loosen…consider using a Loc-Tite product to keep hardware secure.

This process will keep the machine in safe working condition. Also, visually inspect machine for any

damage.

• Verify that the auger gearbox, located between your right and left auger blades, has substantial

lubricant in the casing.

The gearbox fill and drain plugs (bolts) are the only “vertical” plugs (bolts) on the gearbox assembly

when viewed in the standing position. The top plug (bolt) is used for filling…the bottom plug (bolt) is

for draining. Simply remove the top plug (bolt) for verification of lubricant, as it should be inside. To

drain, simply remove bottom plug (bolt).

• Do not change the engine governor setting or overspeed the engine. The governor controls the

maximum safe operating speed of the engine.

•

Snow thrower auger belts, shave plates, shear pins and skid shoes are subject to

wear and damage, therefore it is expected that the owner assume personal

responsibility for the maintenance (removal & installation) of these items.

• For your safety protection, frequently check all components and replace with original equipment

manufacturers (OEM) parts only. Use of parts which do not meet the original equipment

specifications may lead to improper performance and compromise safety.

• Check (drive & auger) control lever (handles) and cables periodically to verify they engage and

disengage properly and adjust, if necessary. Refer to the adjustment section in this operator's manual

for instructions.

• Maintain or replace safety and instruction labels, as necessary.

• Observe proper disposal laws and regulations for gas, oil, etc. to protect the environment.

• Prior to storing, run machine a few minutes to clear snow from machine and prevent freeze up of

auger impeller and completely wipe down unit, while inspecting for frozen components.

• Never store the machine or fuel container inside where there is an open flame, spark or pilot light

such as water heater, furnace, clothes dryer etc.

• Always refer to the operator's manual for proper instructions on off-season storage. A YouTube video

7

is available, which illustrates this process: https://www.youtube.com/watch?v=X4KYcFEfeY4

• Check fuel line, tank, cap and fittings frequently for cracks or leaks. Replace if necessary.

• Do not crank engine with spark plug removed.

• Have the machine inspected annually by an authorized service dealer to ensure that all mechanical

and safety systems are working properly and have not worn excessively*. Failure to do so can result

in accidents, injuries or death.

*Please note that an annual inspection is not covered within the warranty program…only

REPAIR service.

CLEANING

1. To clean your Snow Thrower, use a damp cloth and mild detergent on the surfaces only. Never get

soap or water inside the working mechanisms of your Snow Thrower.Do not clean with water.

Water will freeze due to low temperature and damage the machine.

2. Clean the Snow Thrower of snow and ice buildup before storing or transporting. Be sure to secure the

unit while transporting.

3. Inspect the Snow Thrower carefully for worn, loose, or damaged parts. Check connections and

screws and tighten if necessary.

DO NOT MODIFY THE ENGINE

To avoid serious injury or death, do not modify engine in any way. Tampering with the governor setting

can lead to a runaway engine and cause it to operate at unsafe speeds. Never tamper with factory setting

of engine governor.

KNOWING YOUR SNOW THROWER

Use the illustrations below to become familiar with the locations and functions of the various components

and controls of this snow thrower.

1 2 3 4 5 6 7

19

18

17

16

15

14

13

12

11

10

9

8

1

Drive Control Lever

10

Auger Blade

2

Drive Speed/Gear Control

11

Skid Shoe

3

Chute Deflector Control

12

Tire

4

Auger Control Lever

13

Belt Cover

5

Chute Rotation Handle

14

Electric Start Button

6

Clean Out Tool

15

Lower Handle

7

Discharge Chute Deflector

16

Recoil Start Handle

8

Discharge Chute

17

Handle Nut

9

Auger Housing

18

Oil Dipstick

19

Light

(PSSW26LED/PSS2260LED/PSSHD26-

LED only)

20

21 22 23

20

Fuel Tank Cap

22

Switch Key

21

Primer Bulb

23

Choke Lever

Drive Control Lever

Located on the right side of the upper handle, the Drive Control Handle is used to engage and

disengage the drive wheels. Squeeze the Drive Control Handle against the upper handle to engage the

wheels; release to disengage.

Drive Speed/Gear Control

The Speed/Gear Control is located on the center of the panel and is used to set the drive speed and

direction of travel. It can be moved into any of eight positions (six forward and two reverse gear

settings)

Auger Control Lever

Located on the left side of the upper handle, the Auger Control Handle is used to engage and

disengage the augers. Squeeze the Auger Control Handle to engage the augers; release to disengage

the augers.

Chute Rotation Handle

To adjust snow discharge direction, rotate the handle clockwise or counter-clockwise…. should

rotate 180 degrees.

Skid Shoe

Position the shoes based on the surface conditions. Adjust upward for hard-packed snow. Adjust

downward when operating on gravel or crushed rock surfaces.

9

Auger Blade and Impeller

When engaged, the auger blades rotate to cut snow and direct it into the auger/impeller housing to be

discharged out the chute.

Clean-out Tool

The chute Clean-out Tool is conveniently fastened to the rear of the auger housing with a mounting

clip. It is used to clean the chute assembly and chute opening when snow and ice become lodged.

WARNING! Never use your hands to clear a clogged chute assembly. Shut off engine and remain

behind handles until all moving parts have stopped before unclogging.

LED Light

Located on the front of the panel, this feature provides extra light for increased visibility. This

function only for PSSW26LED/PSS2260LED/PSSHD26-LED.

SNOW THROWER PREPARATION

ADD OIL

The snow thrower is shipped without oil. User must add the proper amount of oil before operating the

snow blower for the first time. The oil capacity of the engine crankcase is 16 fl. oz. For general use, we

recommend 5W-30, 4-stroke engine oil.

ENGINE OIL RECOMMENDATIONS

Select good quality detergent oil bearing the American Petroleum Institute (API) service classifications

SJ, SL, or SM (synthetic oils may be used). Use the ASE viscosity grade of oil from the following chart

that matches the starting temperature anticipated before the next oil changes.

To add oil, follow these steps:

1. Make sure the snow thrower is on a level surface. Tilting the snow thrower to assist in filling will

cause oil to flow into engine areas and will cause damage. Keep snow thrower level!

2. Remove the dipstick from the engine.

3. Add oil slowly as to not overflow the unit.

4. To check the oil level, wipe the dipstick with a clean rag. Insert

the dipstick into the oil fill opening without screwing it in.

Remove the dipstick to check the oil mark.

5. Slowly add more oil and repeat step 4 until the oil mark reaches to

the top of the dipstick. Do not overfill the crankcase.

6. Check for oil leaks. Tighten dipstick firmly.

ADD GASOLINE

Use fresh (within 30 days from purchase), lead-free gasoline with a minimum of 87 octane rating. Do not

mix oil with gasoline.

To add gasoline, follow these steps:

1. Make sure the snow thrower is on a level surface.

2. Unscrew fuel tank cap and set aside. NOTE: The fuel cap may be tight and hard to unscrew.

3. Slowly add unleaded gasoline to the fuel tank. Be careful not to overfill. The capacity of the fuel tank

is 0.66 gallons. NOTE: Do not fill the fuel tank to the very top. Gasoline will expand and spill over

during use even with the fuel cap in place.

4. Reinstall fuel cap and wipe clean any spilled gasoline with a dry cloth.

10

IMPORTANT:

• Never use an oil/gasoline mixture.

• Never use old gasoline.

• Avoid getting dirt or water into the fuel tank.

• Gasoline can age in the tank and make starting difficult. Never store snow thrower for extended

periods of time with fuel in the tank or the carburetor.

NOTE: After completing the above preparation, the engine is ready to be started.

WARNING! Keep the area of operation free from foreign objects that can be thrown by the auger and/or

impeller blades. Perform a thorough inspection of the area since some objects may be hidden from view by

surrounding snow. If the snow thrower hits an obstruction or picks up a foreign object during use, stop the

snow thrower immediately, remove the obstruction, and inspect it for damage. Repair or replace any

damaged parts before restarting and operating you snow thrower.

• Keep children, pets, and bystanders away from the area of operation. Be aware that the normal noise of

the snow thrower when turned on may make it difficult for you to hear approaching people.

• Start your clearing path by throwing snow in a back and forth motion. To clear in the opposite

direction, stop your snow thrower and pivot it on its’ wheels to face the opposite direction. Make sure

to overlap clearing paths.

• Determine the direction of the wind. If possible, move in the same direction as the wind so that the

snow is not thrown against the wind, back into your face and on the just cleared path.

WARNING! DO NOT USE YOUR HANDS TO UNCLOG CHUTE. Stop the motor before removing

debris. Use the supplied Clean-out tool to unclog the chute. Do not walk in front of your running snow

thrower. Do not direct discharged snow towards bystanders.

• Do not apply additional man-made load to the engine since this may damage the engine.

• Some parts of your snow thrower may freeze under extreme temperature conditions. Do not attempt to

operate your snow thrower with frozen parts. If the parts freeze while your snow thrower is in use, stop

the unit and inspect it for frozen parts. Thaw all parts before restarting and operating your snow

thrower. Never force parts or controls that are frozen. Never use an open flame of any sort to thaw

frozen parts.

Pre-Operation Inspection - IMPORTANT!!!

Before using your snow thrower for the first time, check the following:

• Have you read and followed all setup and operation procedures for the engine as outlined?

• Has the engine been filled with oil and gasoline to the proper level?

• Are all snow thrower components properly attached and assembled?

• Are there any broken or damaged parts?

• Are all fasteners tight?

• Are the tires inflated to the proper pressure?

NOTICE: If you are unsure about the assembly or condition of any of your snow thrower parts, please call

our customer service department at (800)791 9458.

AUGER AND DRIVE CONTROLS

1. To engage the auger (blades), press down on the auger control lever (left side handle).

2. To engage the drive, press down on the drive control lever (right side handle). The machine should

start moving in the direction and speed for the respective setting on the speed/gear control.

When finished clearing a snow path, release the auger control lever (handle) and the drive control lever

(handle)

Attention: Release (disengage) the auger and drive control lever (handles) before adjusting the

drive speed control lever. NEVER change the drive/gear speed while your snow thrower is in motion,

as it will damage the drive mechanism and void the warranty.

11

DRIVE SPEED/GEAR CONTROL

Move the drive speed control lever to the desired speed. There are eight (8)

settings: six (6) forward speeds and two (2) reverse speeds. 1 is the slowest

forward speed and 6 is the fastest forward speed. R1 is the slowest reverse

speed and R2 is the fastest reverse speed.

Note: There is no neutral drive setting since the drive control handle must be

engaged for movement. Neutral is achieved when the drive control handle is

disengaged.

CHUTE DISCHARGE DIRECTION ADJUSTMENT

WARNING - Never direct the snow discharge chute at the operator, bystanders, vehicles,

or nearby windows. Discharged snow and foreign objects accidentally picked up by the

Snow Thrower can cause serious damage and severe bodily injury. Always point the

discharge chute in the opposite direction from potential hazards. The discharge chute can

be adjusted 180º by rotating the chute rotation handle. Rotate the chute rotation handle

clockwise to move the discharge chute to the right; counterclockwise to move the chute

to the left.

SKID SHOES ADJUSTMENT

Adjustment of the skid shoes sets the height above the ground at which the auger shave plate operates.

For clearing snow from concrete, asphalt, and other smooth surfaces, set the auger shave plate so that the

bottom of the plate is just above the ground.

For clearing snow from gravel, dirt, and other rough surfaces set the auger shave plate slightly above the

ground to avoid dirt and gravel from entering the auger.

The optimal height of the plate will vary depending on the type of surface being cleared. Surfaces with

larger gravel or stones require a higher shave plate setting.

1. Move the snow thrower to a solid, smooth, and level surface.

2. Place a spacer board on the ground underneath the auger shave plate between the skid shoes. The

thickness of the board should be the same as the height above the ground you wish to raise the auger

shave plate. The skid shoes should not touch the board.

With the two nuts loose allow the skid shoe to slide to the ground then tighten the nuts to secure the skid

shoe.

OPERATING YOUR SNOW THROWER

MANUAL START THE ENGINE

To manual start the engine, perform the following steps:

1. Check the oil and fuel levels.

2. Move the choke lever to the “CLOSE” position.

3. Make sure insert the switch key.

4. Press the primer bulb 3 times.

5. Pull on the recoil starter handle slowly until a slight resistance is felt, then pull quickly to start the

engine. Return cord gently into the recoil starter. Never allow the cord to snap back.

6. If engine fails to start, repeat step 4. NOTE: After repeated failed attempts to start the engine, please

consult the troubleshooting guide before attempting again. If problems persist, please call customer

service.

7. Once the engine has started, slowly return the choke lever all the way to the “OPEN” position.

8. Allow the engine to run for several minutes before cleaning snow. This allows the engine to stabilize

its speed and temperature.

12

ELECTRIC START THE ENGINE

To start the engine using the electric start function, perform the following steps:

1. Check the oil and gas levels.

2. Move the choke lever to the “CLOSE” position.

3. Make sure insert the switch key.

4. Press the primer bulb 3 times.

5. Plug the power cord to starting motor.

6. Press the start button for 2-3 seconds or until the engine starts. NOTE: If the engine does not start

after 2-3 seconds, release the start button.

7. If engine fails to start, wait 10 seconds, then repeat step 6. NOTE: After repeated attempts to start the

engine, please consult the troubleshooting guide before attempting again. If problems persist, please

call customer service.

8. Once the engine has started. Slowly move the choke lever all the way to the “OPEN” position. Allow

the engine to run for several minutes before attempting to clean snow.

CLEARING SNOW

Start the engine once your snow thrower has been running outside for several minutes, it is now ready for

use. Make sure the path in front of your Snow Thrower is free from people, animals, objects, and all other

obstructions except for snow.

Adjust the chute outlet to the desired direction.

Turn the chute rotation handle clockwise or counter-clockwise until the desired position is reached.

WARNING! Never direct the chute outlet toward people or animals. While snow may seem harmless, it can

contain rocks or other debris that can cause serious injury when projected through the chute.

1. Engage/depress the auger control lever (handle) to start the augers and impeller turning.

2. Set the desired direction and speed using the speed/gear control lever.

3. Engage/depress the drive control lever (handle) and direct the snow thrower into the snow to be cleared.

NOTICE: NEVER change speed/gear positions while the drive control lever (handle) is engaged.

Disengage the drive control handle BEFORE changing speeds or directions. If the snow is deeper

than the height of the auger, remove it in several steps taking narrower swaths. Make several passes

with the auger overlapping the cleared areas and reduce forward speed.

For the best clearing efficiency, clear snow before it melts, refreezes and hardens. Hard

packed and wet snow can be very difficult to clear.

Clearing wet heavy snow can be a challenge, depending on ambient temperature, humidity levels, and

overall climate conditions including actual snow conditions, there may be no 100% solution as snow

may be too wet or compacted to move or throw. Wet snow will tend to clog and stick more to the augers

and chute. Keep the auger engaged as much as possible when clearing wet snow to help prevent

clogging.

WARNING!

If snow is filled with foreign material, damage to the snow thrower may result.

Avoid snow with foreign materials.

STOPPING

When finished using your snow thrower, perform the following steps to shut it down.

1. Engage the auger and impeller for 30 seconds to clear any remaining snow inside your snow thrower

2. Stop the auger blade rotation by releasing the (left) auger control lever (handle).

3. Remove Engine Safety Switch Key to stop engine operation.

4. Remove snow from all snow thrower surfaces including the auger housing and chute areas.

CLEARING RESTRICTIONS

If the snow discharge chute or auger housing becomes clogged, STOP the engine. Remove the Engine Safety

key and make sure that all rotating parts have come to a complete stop. Use the supplied snow clean out tool to

clear the obstruction. After unclogging, wipe the tool clean, and place it in the holder on top of the auger

housing.

13

MAINTENANCE

TIRE INFLATION

Before each use of your Snow Thrower, check the tire pressure. The pressure in each tire should be in the range

of 20-24 psi for the best performance. The pressure can be checked using an ordinary tire pressure gauge. Fill

the tires using a small or pressure regulated air compressor.

WARNING! DO NOT OVER-INFLATE THE TIRES. Over-inflating could cause a tire to burst and

cause severe bodily injury.

SHAVE PLATE REPLACEMENT

Remove both skid shoes and hardware including carriage bolts and nuts which attach shave plate to snow

thrower housing. Reassemble new shave plate, making sure heads of the carriage bolts are to the inside of the

auger housing.

AUGER OR IMPELLER JAMS

WARNING! The auger and impeller rotate at fast speeds which can cause harm or even

amputation to a person's body parts. Even if you do not see the auger or impeller

rotating, it may start at any time if the engine is running. Remove the Safety Key before

cleaning the jams.The chute clean-out tool is fastened to the upper tube with mounting

clips.

1. Always turn OFF the engine before attempting to clear any clogs or jams.

2. Keep hands and feet away from rotating parts while the engine is running.

3. Do not wear loose fitting clothing that can become entangled in rotating parts.

4. Wait until the auger and impeller have come to a full stop.

5. Clear any visible jams using the clean out tool attached to your machine.

WARNING! DO NOT

try to clear jams with your hands or feet.

AUGER SHEAR PINS REPLACEMENT

Shear pins are used to attach the auger shaft to the auger blades. Stop the engine by

removing the safety key. A clog or jam in the augers may cause one or multiple shear

pins to break. The shear pins are a safety mechanism and designed to break under

high load or impact and protect the auger drive system from damage. Replacement

shear pins and nylon locknuts are provided with your snow thrower.

For additional replacement shear pins, please call the customer service department at

(800)791 9458.

1. Turn off the engine and wait for all moving parts to come to a complete stop. Remove any

remnants of the broken shear pin. It may be necessary to unscrew the nut from the broken shear

pin and drive out the broken pin.

2. Insert a new shear pin through the hole in the auger shaft and tighten using the shear pin nylon

locknut. Do not over-tighten the nylon locknut. Note: Never replace the shear pins with standard

pins or fasteners. Damage may occur to the snow blower and drive systems.

NOTICE: Never replace the shear pins with standard pins or fasteners. Damage may occur to the snow

blower and drive systems.

14

TROUBLESHOOTING

Problem

Causes

Remedy

WARNING - Before attempting to make any inspections, repairs or adjustments, stop the engine, wait for all moving parts to

stop moving and carefully disconnect the engine spark plug wire. If tipping or

turning the snow blower is required for any inspection or repair, first wait until the engine is cool to the touch and then drain the

engine of all fuel and oil into suitable containers and store or dispose of in a proper manner.

Engine Systems - Note: For all engine problems, see the below troubleshooting information.

Engine Fails to

Start

(Engine cranks

over)

Spark plug wire disconnected

Connect wire to spark plug

Faulty spark plug

Clean, adjust gap, or replace spark plug.

Engine flooded with fuel

Discontinue choke or primer use, clean or replace spark

plug.

Safety key not inserted in engine ignition

Insert key fully into the switch

Choke not in START position

Move choke to START position, after engine starts

slowly move to RUN position as engine speed and

operation stabilizes at the set rpm. If engine still does not

start move to half choke and crank engine.

Fuel incorrect, old or stale, will not ignite

Empty and clean fuel tank & carburetor, refill with fresh,

clean gasoline. (Note: Fuel may become stale after 30

days in some cases)

Blocked or clogged fuel system or line

Clean fuel system or line

Extension cord is not properly attached to electric

starter terminal

Re-insert extension cord into electric starter terminal.

Engine electric

starter

will not crank

engine

No power from power supply, tripped breaker

Check power supply extension cord is attached to.

Extension cord wire gauge is too small, or cord

is too long

Use proper rated and length extension cord

CHOKE in ON or partial ON position

Move CHOKE lever to RUN

Engine runs

erratic,

stalls or seems

low on

power

Fuel incorrect, old or stale

Empty and clean fuel tank & carburetor, refill with fresh,

clean gasoline. (Note: Fuel may become stale after

30 days in some cases)

Blocked or clogged fuel system or line

Clean fuel system or line

Carburetor is in need of cleaning

Clean fuel system and carburetor

Spark plug wire loose

Connect and tighten spark plug wire

Faulty spark plug

Clean, adjust gap, or replace spark plug, see Engine

Operator's manual

Engine oil over filled

Drain oil to proper level. Oil should not be above the

top 2 threads of LOWER fill plug.

Engine oil level low or empty

Add oil

Drive system

No forward or

reverse drive

movement when

drive handle

engaged

Drive belt loose or damaged

Check drive belt tension pulley for damage or

incorrect tension, repair as necessary. Replace drive

belt.

Friction drive wheel is worn or damaged

Replace friction drive wheel

Friction drive wheel wet or slipping

Allow snow blower to dry and or warm up or

adjust drive cable tension as necessary

Wheel to axle pins broken or missing.

Replace pins attaching wheels to axle

15

Problem

Causes

Remedy

Drive speed control

stuck in gear or

won’t change gears

Speed control lever loose or damaged, not

moving speed control cables

Check speed control lever and cables for damage or

loose or missing parts. Repair or replace parts as

needed, ensure pivot stud spring tension is correct,

adjust pivot nut spring tension as needed.

Speed control cables loose, damaged or

binding

Repair, adjust or replace as necessary

Drive speed control

allows only 1

direction

Speed control cables misadjusted, loose,

damaged or binding

Check speed control lever and cables for damage or

loose or missing parts. Repair or replace parts as

needed. Adjust drive speed control cables, see Drive

Speed Control Cables Adjustment

Drive engaged

when drive control

handle released

Drive control cable binding, won’t release

Repair, replace cable as necessary

Friction drive wheel return spring broke or

missing

Replace spring, adjust cable as necessary

Auger System

Auger not rotating

when auger control

handle engaged or

Not blowing snow

or Poor snow

blowing

performance

Chute assembly clogged

Clean chute and inside of auger housing with

clean-out tool

Auger shear pins broken

Replace shear pins. Check each auger blade shear pin.

Foreign object in auger or impeller causing

auger to stop without shearing pins

Remove object from auger or impeller areas

Auger belt loose, slipping, worn or damaged

Replace auger belt

Auger belt tension cable loose, damaged or

binding

Repair, adjust or replace as necessary

Auger blade(s) damaged or bent

Replace auger blade(s)

Auger gearbox mechanical damage, auger

drive system not rotating freely (binding)

Check bearings, bushings and all system parts for

damage or mechanical binding. Repair or replace as

necessary using proper lubrication

Impeller damaged

Replace impeller

Impeller not connected to impeller shaft,

impeller or shear pins broken

Replace shear pins or impeller as necessary

Forward speed too fast while blowing snow,

overload

Allow engine to maintain its speed.

Auger belt broken, or

repeated failure

Auger tension pulley arm return spring broken

or missing

Replace tension arm return spring

Auger tension pulley arm stuck or binding

Repair or replace tension arm as necessary

Auger tension pulley arm or pulley

misaligned or damaged

Repair, replace or align tension arm and or pulley as

necessary

Foreign material on pulleys and belt, oil,

grease, dirt etc.

Clean belt and pulleys as necessary, replace belt if

necessary

Auger pulleys misaligned, loose, damaged, or

bent

Replace or align pulleys as necessary

Incorrect or damaged auger belt

Replace with correct size and type belt

Auger belt guide pin not adjusted

Adjust belt guide pin to within 1/8 to 3/16 in. from

pulley. (Guide pin keeps belt in pulley when

disengaged)

Auger rotating

when auger control

handle released

Auger tension pulley arm return spring broken

or missing

Replace tension arm return spring

16

EXPLODED VIEW AND PARTS LIST

PANEL ASSEMBLY

17

Item

Stock #

Description

Qty

Item

Stock #

Description

Qty

1

303020498

Hex Flange Bolt M8X18

4

25

303071336

Right Operation Trigger

1

2

303160909

Lower tube

1

26

303030130

Flang Nut M6

2

3

303020154

Bolt M8x40

4

27

303030077

Flang Lock Nut M8

2

4

303030077

Hex Flange Nut M8

4

28

203070085

Control Handle

1

5

303200050

Lower Drive Cable

1

29

203021099

Walking cable control

panel

1

6

303200012

Lower Auger Cable

1

30

203020380

Dental Pad

1

7

303071442A

Speed Control Connection

Rod

1

31

303020655

Bolt M8x45

1

8

303030076

Flange Normal Nut M8

2

32

303010353

Screw 6×16

3

9

303160845

Dowel Pin φ2

1

33

303160746

Cushion Cover

3

10

303042023

Flat Washer φ8×φ18×2

1

34

303071343

DB7109 Gear Plate

1

11

303123034

Connection Rod Pin Φ7

1

35

301100037

PSSW26LED

PSS2260LED

PSSHD26-LED

Light Switch

1

12

303200106

Upper Auger Cable

1

36

203050637

PSSW26LED

PSS2260LED

PSSHD26-LED

Panel

1

13

303200130

Upper Drive Cable

1

303071343

PSS2260L

14

203050057

Clean Out Tool

1

37

303030077

Flange Lock Nut M8

4

15

203050512

Rocker Seat

1

38

303042013

Flat Washerφ8×φ22×2

4

16

303010164

Screw M6×20

1

39

303020275

Hex Washer Bolt

M8X40

4

17

303181339

Upper Handle Welding

1

40

303010313

PSSW26LED

PSS2260LED

PSSHD26-LED

Screw

4

18

303020486

Hex Flange Bolt M6X50

2

41

203050561

PSSW26LED

PSS2260LED

PSSHD26-LED

Back Cover For Lamp

1

19

203070105

Handle Cover

2

42

301013053

PSSW26LED

PSS2260LED

PSSHD26-LED

Lamp Panel

1

20

303181183

Left Operation Trigger

1

43

203030007

PSSW26LED

PSS2260LED

PSSHD26-LED

Transparent lamp cup

3

21

203070102

Control Hand Head

1

44

203030008

PSSW26LED

PSS2260LED

PSSHD26-LED

Lamp Cover

1

22

303020654

Bolt M8x35

1

45

301040130

PSSW26LED

PSS2260LED

PSSHD26-LED

Connecting Line

2

23

303130369

Compression Spring

2

46

306010059

PSSW26LED

PSS2260LED

PSSHD26-LED

Battery Box

1

24

303030077

Flang Lock Nut M8

2

18

CHUTE ASSEMBLY

Item

Stock #

Description

Qty

Item

Stock #

Description

Qty

1

203050514

Chute

1

21

303030077

Locknut M8

1

2

303030087

Hex Flange Nut M6

1

22

303130369

Pressure Spring

1

3

303071344

Cable Seat

1

23

303071056A

Locating Plate

1

4

303020244

Hex Flange Bolt M6×14

1

24

203020380

Dental Pad

2

5

303200117

Chute Mouth Cable

1

25

303030087

Hex Flange Nut M6

2

6

303030077

Hex Flange Nut M8

2

26

303160865

Pull wire Support Rod

1

7

303020622

Bolt M8X20

2

27

303020655

Hex Bolt M8X45

1

8

203050515

Chute Mouth

1

28

303020246

Bolt M6X16

2

9

203021301

Steering Gear

1

29

303030032

Locknut M6

2

10

303042019

Flat Washer

2

30

303060131A

Steering Gear

1

11

303010026

Screw

2

31

203010818

Steering Gear Seat

1

12

306110029

Rivet φ6 × 10

3

32

203010817

Steering Gear Cover

1

13

303071053

Steering Fix Plate

1

33

303010026

Screw 4X12

2

14

303020655

Hex Bolt M8×45

2

34

303043058

Flat Washer

1

15

303041022

Spring Washer

2

35

303050044

Shaft Ring

1

16

303042023

Flat Washer φ8×φ18×2

2

36

303160845

Butterfly Pin

1

17

303081254

Chute Support Tube

1

37

303160905

Z-bar

1

18

303020503

Hex Flange Bolt M6×35

2

38

303042004

Flat Washer φ10 × φ22 × 2

2

19

303030087

Hex Flange Nut

2

39

203021460

Rocker Lever

1

20

303181335

Small Support Pipe

Welding

1

40

303050029

Shaft Ring

1

19

FRAME ASSEMBLY

20

Item

Stock #

Description

Qty

Item

Stock #

Description

Qty

1

9999960501

Engine

1

41

303100051

Ball Bearing

2

303160192

Spacer Bush

1

42

303160799

Six Square Axis

1

3

303070202

Small Tensioning Plate

1

43

303042004

Flat Washer Φ10*Φ22*2

2

4

303042005

Flat Washer φ8×φ28×3

2

44

303343043

Locknut M10

1

5

303020501

Hex Flange Bolt M8×30

1

45

303525287

Big raft

1

6

303030077

Flange locknut M8

1

46

303586035

Triangular Head Bolt

4

7

203100004

Tension Wheel Assembly

1

47

303050027

Shaft Ring Φ30

1

8

303160195A

Bushing

1

48

303210036

Fork Riveting

1

9

303020154

Step Bolt M8×40

1

49

303160803

Six Square Sleeve

1

10

303130094

Friction Wheel Bracket Spring

1

50

202170009

Friction Wheel Assembly

1

11

303020124

Flange Hex Bolt M8×35

1

51

303041009

Spring Washer Φ6

3

12

303042005

Flat Washer φ8×φ28×3

1

52

303020244

Hex Flange Bolt M6×14

3

13

9141960501

Flat Key 4.7

1

53

303030077

Hex Flange Nut

4

14

303160152A

V-belt Wheel

1

54

303130094

Friction wheel bracket spring

1

15

303060041

Synchronous Pulley Wheel

1

55

304315011

Serrated Nut

1

16

303060040

Adjustable Pad

1

56

304375759

Elastic Washer

1

17

303160432

Screw M8

1

57

303042004

Flat Washer

1

18

303020279

Hexagon Bolt M8X20

1

58

303181163

Friction Wheel Support Welding

1

19

303041022

Tension SpringΦ8

1

59

304132767

Flat Washer

1

20

303042023

Flat Washer

2

60

303020244

Outer Hex Flange Bolt

1

21

303081251

Belt Stop Lever

1

61

303160801

Large Synchronous Belt Pulley

1

22

303043016

External Teeth Lock Washer

1

62

304618751

Rim

1

23

303160177

Guide Pulley Screw

1

63

304679499

Screw

6

24

203020364

Guide Pulley

1

64

303160802

Large Synchronous Belt Shaft

1

25

303030032

Locknut M6

1

65

304800995

Deep Groove Ball Bearing

1

26

303030066

Nut M8

4

66

303042169

Flat Washer φ17×φ24×3

1

27

303041022

Spring Washer

4

67

303050519

Retaining Ring Φ40

1

28

303042023

Flat Washer φ8×φ18×2

4

68

302040078

Synchronous Belt

1

29

303030032

Locknut M6

2

69

304922491

Flange Bolt M6X12

2

30

303070418A

Guide Wheel Plate

1

70

203050335

Belt Cover

1

31

303181227

Shift Fork Welding

1

71

303160845

Butterfly Pin

2

32

303160308

Friction Wheel Support Shaft

Sleeve Tube

1

72

303160815

Wheel Bolt

2

33

303160830A

Paddle Shift

1

73

302090217

13" Wheel Assembly

2

34

303030077

Hex Flange Nut M8

1

74

305165483

Spacer Bush

2

35

303071243

Guide Wheel Plate

1

75

305226231

Shaft Ring Φ19

1

36

203020364

Guide Pulley

2

76

305286979

Bushing

2

37

303160177

Guide Pulley Screw M6X35

2

77

303160876

Big gear

1

38

303020561

Hex Flange Bolt M6X16

4

78

303160845

Butterfly Pin

2

39

303181006

Chassis Welded

1

79

303160815

Wheel Bolt

2

40

303020239

Hex Flang Bolt M10X20

1

80

303160880

Shaft

1

La page charge ...

PowerSmart PSSW2260LED Manuel utilisateur

PowerSmart PSSW2260LED Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents