RACOS L-RA1 BLE Communication Automatic Door Control Device Manuel utilisateur

RACOS

User Manual

L-RA1

2022-1-5

User Manual (ver0.04)

L-RA1

Page 1 / 10

www.racosys.com

Content

1. Features ------------------------------------------- 2

2. Applications ---------------------------------------2

3. Description ----------------------------------------2

4. Product information ------------------------------4

5. Environmental Conditions -----------------------6

6. Product Composition -----------------------------7

7. Circuit contents -----------------------------------7

8. Electrical specification ----------------------------8

9. In/Out (CN1, Molex 5267-05S) ------------------8

User Manual (ver0.04)

L-RA1

Page 2 / 10

www.racosys.com

1. Features

O LG robot and BLE communication interface are connected to control automatic

door opening and door closing. Hereinafter, Mac Address setting and BLE

output(dBm) adjustment through a separate dip switch setting. Each control state

can be checked through the LED. Relay output state value can select no

power/DC12V. (Using jumper pins)

2. Applications

 LG Electronics guide robot

3. Description

It is a BLE communication automatic door control device that is linked to LG

Electronics’ guide robot. The power connection and relay output terminal of the

device are connected to Molex(5267-05P), and when the power supply and

automatic door contact control lines are connected, the control is ready. Afterwards,

control is performed through a BLE communication connection with LG Electronics’

guide robot (control through a separate communication protocol).

The main functions are as follows

 Automatic door control through LG Electronics’ guide robot and BLE

communication connection (door open, door closed)

User Manual (ver0.04)

L-RA1

Page 3 / 10

www.racosys.com

[Figure 3] Operation Block Diagram

User Manual (ver0.04)

L-RA1

Page 4 / 10

www.racosys.com

4. Product information

[Figure 9.1 L-RA1 The front part]

[Figure 9.2 L-RA1 The back part]

User Manual (ver0.04)

L-RA1

Page 5 / 10

www.racosys.com

[Figure 9.3 L-RA1 The size of the front part of the size]

[Figure 9.4 L-RA1 The size of the back part of the size]

User Manual (ver0.04)

L-RA1

Page 6 / 10

www.racosys.com

Item Content

Size 45x45x11.1 (mm)

Frequency 2.4GHz

Power Max EIRP -1dBm

In-box

Accessories

SSWH5264ASY-5P (Molex 5267-05S For connection),

Screw, Screw support

5. Environmental Conditions

Item Standard

Voltage Range Dc Link 12V±5%

Operating

Condition

Temperature

Relay -20℃ ~ 50℃

Main MCU -20℃ ~ 50℃

BLE MCU -20℃ ~ 50℃

Humidity 85% RH MAX

Storage Condition

Temperature

Relay -40℃ ~ 70℃

Main MCU -40℃ ~ 85℃

BLE MCU -40℃ ~ 125℃

Humidity 85% RH MAX

Posture Shaft Horizontal Only

Note: No Dew Condensation

User Manual (ver0.04)

L-RA1

Page 7 / 10

www.racosys.com

6. Product Composition

Item Content

Main PCB

Power DC 12V

Use

Transmitting and

receiving data

from BLE Module,

Relay Control

BLE Module

Power DC 3.3V

Use

Transmitting and

receiving data

from Main PCB,

Connect to BLE

Device

7. Circuit contents

Item Content

Constant voltage

circuit

AP1509-50S(12V->5V), LM1117-3.3(5V->3.3V)

Relay circuit DS1E-M-DC5V (2 Ch, A&B Contact point)

LED circuit LED for status display

When power is applied for the first time, all LEDs are lit

up. Red LED lights when detecting a switch change.

Blue LED lights up when receiving the BLE signal.

White LED lights during relay operation.

Switch circuit SW1: Address setting switch (MAC)

SW2: Output setting switch (BLE TX dBm)

User Manual (ver0.04)

L-RA1

Page 8 / 10

www.racosys.com

8. Electrical specification

Item Standard

Rated voltage DC12V±5% DC Link

Standby current 13mA

Operating current

75mA

9. In/Out (CN1, Molex 5267-05S)

1P 2P 3P 4P 5P

VCC GND NO COM NC

 When the locking device requests DC12V input, the jumper pin can be

connected to supply DC12V.

10. Federal Communications Commission(FCC)

Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

User Manual (ver0.04)

L-RA1

Page 9 / 10

www.racosys.com

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected

- Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions:

1) This device may not cause harmful interference, and

2) This device must accept any interference received, including interference that may

cause undesired operation.

You are cautioned that changes or modifications not expressly approved by the part responsible

for compliance could void the user’s authority to operate the equipment.

FCC Caution

Any changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate this equipment and For indoor use only, use outdoors

or in other modes not covered by this manual may violate the FCC regulation and violate the user

authority to use the product.

FCC RF Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. End users must follow the specific operating instructions for satisfying RF exposure

compliance.

Supplier's Declaration of Conformity

47 CFR § 2.1077 Compliance Information

Responsible Party – U.S. Contact Information

LG ELECTRONICS U.S.A, INC.

Street Address: 111 SYLVAN AVENUE, NORTH BUILDING

ENGLEWOOD CLIFFS, N.J. 07632

City, State: U.S.A

Telephone number or internet contact information

User Manual (ver0.04)

L-RA1

Page 10 / 10

www.racosys.com

- Name : Kyung-Su Han

- Telephone number : 1-201-266-2215

- Internet contact information : kyungsu[email protected]m

Industry Canada Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science

and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following

two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired

operation of the device.

Avis d’Industrie Canada

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR

d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio

exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :

(1) L’appareil ne doit pas produire de brouillage;

(2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est

susceptible d’en compromettre le fonctionnement.

IC Radiation Exposure Statement

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment.

NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE

CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS

COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

Avis d’Industrie Canada sur l’exposition aux rayonnements

Cet appareil est conforme aux limites d’exposition aux rayonnements d’Industrie Canada pour un

environnement non contrôlé.

REMARQUE : LE FABRICANT N’EST PAS RESPONSABLE DES INTERFÉRENCES RADIOÉLECTRIQUES

CAUSÉES PAR DES MODIFICATIONS NON AUTORISÉES APPORTÉES À CET APPAREIL. DE TELLES

MODIFICATIONS POURRAIENT ANNULER L’AUTORISATION ACCORDÉE À L’UTILISATEUR DE FAIRE

FONCTIONNER L’APPAREIL.

RACOS L-RA1 BLE Communication Automatic Door Control Device Manuel utilisateur

RACOS L-RA1 BLE Communication Automatic Door Control Device Manuel utilisateur

dans d''autres langues

Autres documents