Garland MST54 Mode d'emploi

Part # 4517124 Rev. 7 (08/17/11)

Users are cautioned that maintenance and repairs must be performed by a Garland authorized service agent

using genuine Garland replacement parts. Garland will have no obligation with respect to any product that has been

improperly installed, adjusted, operated or not maintained in accordance with national and local codes or installation

instructions provided with the product, or any product that has its serial number defaced, obliterated or removed,

or which has been modified or repaired using unauthorized parts or by unauthorized service agents.

For a list of authorized service agents, please refer to the Garland web site at http://www.garland-group.com.

The information contained herein, (including design and parts specifications), may be superseded and is subject

to change without notice.

FOR YOUR SAFETY:

DO NOT STORE OR USE GASOLINE

OR OTHER FLAMMABLE VAPORS OR

LIQUIDS IN THE VICINITY OF

THIS OR ANY OTHER

APPLIANCE

WARNING:

IMPROPER INSTALLATION, ADJUSTMENT,

ALTERATION, SERVICE OR MAINTENANCE

CAN CAUSE PROPERTY DAMAGE, INJURY,

OR DEATH. READ THE INSTALLATION,

OPERATING AND MAINTENANCE

INSTRUCTIONS THOROUGHLY

BEFORE INSTALLING OR

SERVICING THIS EQUIPMENT

PLEASE READ ALL SECTIONS OF THIS MANUAL

AND RETAIN FOR FUTURE REFERENCE.

THIS PRODUCT HAS BEEN CERTIFIED AS

COMMERCIAL COOKING EQUIPMENT AND

MUST BE INSTALLED BY PROFESSIONAL

PERSONNEL AS SPECIFIED.

IN THE COMMONWEALTH OF MASSACHUSETTS

THIS PRODUCT MUST BE INSTALLED BY A

LICENSED PLUMBER OR GAS FITTER. APPROVAL

NUMBER: G-1-07-05-28

For Your Safety:

Post in a prominent location, instructions to be

followed in the event the user smells gas. This

information shall be obtained by consulting

your local gas supplier.

INSTALLATION AND

OPERATION, MANUAL

THE GARLAND

GAS XPRESS GRILL,

MODELS XG24, XG36

GARLAND COMMERCIAL RANGES, LTD.

1177 Kamato Road, Mississauga, Ontario L4W 1X4

CANADA

Phone: 905-624-0260

Fax: 905-624-5669

Part # 4517124 Rev. 7 (08/17/11)Page 2

INTRODUCTION

The Garland Xpress Grill provides a method for ecient two-sided cooking, while accommodating a variety of products. The

unit will also serve as a at grill, and meets all standards for safety, eciency, and cleanliness.

Standard Features:

• Stainless steel front, top & sides

• 33,000 BTU/Hr input for each twelve-inch section of

griddle

• Built in pressure regulator, (one per twelve inch section of

griddle), and gas shut-o valve

• ¾" thick, Carbon steel griddle plate, machine ground,

highly polished

• Swivel casters complete with front brakes (4)

• Die cast aluminum electric top heating elements rated

208V, 220V or 240V, single or three-phase

• Automatic lifting and lowering top heaters

• Towel bar with bun pan lip

• Stainless steel dual side grease collectors

• Separate programmable controller for each

twelve-inch section

• Multi-colored LED indicator lights to identify operational

mode

• One year limited parts and labor warranty

(USA & Canada)

Part # 4517124 Rev. 7 (08/17/11) Page 3

TABLE OF CONTENTS

INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Standard Features: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

DIMENSIONS AND SPECIFICATIONS, MODEL XE24 . . . . 4

DIMENSIONS AND SPECIFICATIONS, MODEL XE36 . . . . 5

SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

National Codes Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Gas Connections and Pipe Sizing . . . . . . . . . . . . . . . . . . . . . . . 7

Appliances Equipped with Casters: . . . . . . . . . . . . . . . . . . . . . 8

Swivel Caster Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Electrical Connections: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Ventilation and Clearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

GRILL CONTROLS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Master Power Switch: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

LED Indicators:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Display: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Product Buttons (1-8):. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Power Button: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Program Button: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Temperature Button: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Up/Down Arrow Buttons; 2 Functions: . . . . . . . . . . . . . . . .10

Enter Button: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Cancel/Raise Platen Button, (Green): . . . . . . . . . . . . . . . . . .10

Black Button: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Installing Release Material: . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Lighting Instructions: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Simplied Cook Cycle Instructions: . . . . . . . . . . . . . . . . . . . .12

To Cook in Two-Sided Mode: . . . . . . . . . . . . . . . . . . . . . . . . . .13

To Cook in Flat Grill Mode:. . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Enter Standby Mode:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Exit Standby Mode: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

To Display the Current Temperatures: . . . . . . . . . . . . . . . . . .13

To View Settings for a Menu Item:. . . . . . . . . . . . . . . . . . . . . .13

To Clean the Grill: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

PLATEN SET: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

EXTENDED TIME: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

INSTANT ON TIME: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

START DELAY: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

CLEANING AND MAINTENANCE . . . . . . . . . . . . . . . . . . . . 14

Cleaning During Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Daily Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

PLATTEN ZEROING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

PROGRAMMING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Programming Modes/Menu Sequence: . . . . . . . . . . . . . . . .20

Menu Items...

To Change the Cook Time of a Product: . . . . . . . . . . . . . . . .22

To Turn Platen, (2-Sided), Cooking On/O: . . . . . . . . . . . . .22

To Change Upper Platen Set Temperature: . . . . . . . . . . . . .22

To Change Grill Set Temperature: . . . . . . . . . . . . . . . . . . . . . .22

To Change Product Gap Setting:. . . . . . . . . . . . . . . . . . . . . . .22

To Change Product Button, “Key” Assignment . . . . . . . . . .23

To Change a Product Name: . . . . . . . . . . . . . . . . . . . . . . . . . . .23

System Info...

To View Recovery Time - Upper Platen:. . . . . . . . . . . . . . . . .23

To View Recovery Time - Grill:. . . . . . . . . . . . . . . . . . . . . . . . . .23

To View the Garland Part Number: . . . . . . . . . . . . . . . . . . . . .23

To View the Flash Number: . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

To View the Software Number:. . . . . . . . . . . . . . . . . . . . . . . . .24

To View the Download Number: . . . . . . . . . . . . . . . . . . . . . . .24

System Setup

To Change temperature Units, (°F or °C): . . . . . . . . . . . . . . .24

To Change Gap Setting Display Units:. . . . . . . . . . . . . . . . . .24

To Change the Alarm Volume: . . . . . . . . . . . . . . . . . . . . . . . . .25

To Change the Key Chirp:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

To Change Upper Set Temperature . . . . . . . . . . . . . . . . . . . .25

To Change Grill Set Temperature. . . . . . . . . . . . . . . . . . . . . . .25

To Change Probe Calibration - Upper:. . . . . . . . . . . . . . . . . .25

To Change Probe Calibration - Grill: . . . . . . . . . . . . . . . . . . . .26

To Change Platen Gap Set: . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

To Change Instant-On Time:. . . . . . . . . . . . . . . . . . . . . . . . . . .26

To Change Control Type: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

To Turn Extended Time On/O: . . . . . . . . . . . . . . . . . . . . . . . .27

To Change the Grill Function:. . . . . . . . . . . . . . . . . . . . . . . . . .27

To Change the Start Delay: . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

To Change the Alarm Mode: . . . . . . . . . . . . . . . . . . . . . . . . . . .27

To Turn Clean Mode On/O: . . . . . . . . . . . . . . . . . . . . . . . . . . .28

To Add a Product Name in Library:. . . . . . . . . . . . . . . . . . . . .28

To Modify a Product Name in Library: . . . . . . . . . . . . . . . . . .28

Service Mode

To Change SCK Address:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

To Perform Limit Switch Test: . . . . . . . . . . . . . . . . . . . . . . . . . .29

CALIBRATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Bi-Weekly Calibration:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

ERROR LOGIC & TROUBLESHOOTING. . . . . . . . . . . . . . . . 31

Probe Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Heating Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Platen Down Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Platen Up Error. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Gas Ignition Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

COMM Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Motor Overcurrent Error. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Motor Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Motor Error2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Lower Switch Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Upper Switch Error. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

WIRING DIAGRAM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Part # 4517124 Rev. 7 (08/17/11)Page 4

Garland Commercial Ranges Ltd

1177 Kamato Road,

Mississauga, Ontario

L4W 1X4 CANADA

Phone: 905-624-0260

Fax: 905-624-5669

Master Series Gas Xpress Grill

Form# XG24 (08/02/10)

25-1/2"

[646mm]

AVERAGE

23"

[584mm]

MAX

44.03°

AVERAGE

[48° MAX]

33-25/32"

[858mm]

24-1/8"

[614mm]

11-1/2"

[292mm]

ÉLÉMENT CHAUFFANT

SUPÉRIEUR

(2 ENDROITS)

TOP VIEW

24"

[610mm]

GRILL

PLATE

DEPTH

40-1/4"

[1022mm]

24"

[610mm]

GRILL PLATE WIDTH

3/4"

NPT

GAS

INLET

28-3/16"

[716mm]

FRONT VIEW

11-1/4"

[286mm]

RIGHT SIDE VIEW

7" [178mm] MIN

11" [279mm] MAX

26-23/32"

[678mm]

FROM PLATEN

ARM PIVOT

50-1/2"

[1282mm]

AVERAGE

4-41/64"

[118mm]

1-23/32"

[44mm]

2-3/4"

[70mm]

25-7/8"

[656mm]

38-25/64"

[975mm]

Model

Total

kW

Load

Loading kW/

Phase

Nominal Amps Per Line

208/220/240V 3ph

208V 220V 240V

1-Ph 3-Phase Delta 1-Ph 3-Phase Delta 1-Ph 3-Phase Delta

X-Y X-Z Y-Z L1-L2 X Y Z L1-L2 X Y Z L1-L2 X Y Z

XG24 8.66 2.66 3.33 2.66 41.63

24.90

22.14

24.90

39.36

23.50

20.94

23.50

36.08

21.61 19.19 21.61

XG24-1

L/R

4.33 1.33 1.65 1.33

20.82

12.14 11.07 12.14

19.68

11.75

10.47

11.75

18.04

10.80

9.59

10.80

XG24-F 0.66 – 0.66 – 3.17 2.74 – 2.74 3.00 2.59 – 2.59 2.75 2.38 – 2.38

Model

Total

kW

Load

Loading kW Per Phase Nominal Amps Per Line

380/400/415V 380V 400V 415V

L1/N L1/L2 L1/L3 L2/L3 L1/N L1 L2 L3 L1/N L1 L2 L3 L1/N L1 L2 L3

XG24CE 8.74 0.74 2.66 2.66 2.66 3.36 15.90 12.46 12.46 3.22 13.40 11.55 11.55 3.08 12.10 11.11 11.11

XG24CE-1

L/R

4.56 0.56 1.33 1.33 1.33 2.54 7.33 6.02 6.02 4.30 19.80 17.32 17.32 4.12 18.75 16.70 16.70

XG24CE-F 0.38 0.38 0.00 0.00 0.00 1.72 1.00 0.00 0.00 1.58 0.95 0.00 0.00 0.91 12.10 11.11 11.11

Clearances Gas Pressure

Total Input

Entry Installation Supply (min.) Operating

Crated Uncrated Sides Rear NAT PRO NAT PRO BTU/Hr kW

47-1/2"

(1207mm)

32"

(813mm)

6"

(152mm)

3"

(76mm)

7.0" WC 11.0" WC 3.5" WC 3.5" WC 66,000 19.4

DIMENSIONS & SPECIFICATIONS, XG24

Part # 4517124 Rev. 7 (08/17/11) Page 5

DIMENSIONS & SPECIFICATIONS, XG36

Garland Commercial Ranges Ltd

1177 Kamato Road,

Mississauga, Ontario

L4W 1X4 CANADA

Phone: 905-624-0260

Fax: 905-624-5669

Master Series Gas Xpress Grill

Form# XG36 (08/24/10)

24"

[610mm]

11-1/2"

[292mm]

TOP HEATER

(3 PLACES)

TOP VIEW

40-1/4"

[1022mm]

GRILL PLATE 24"x 36"

[610mm x 914mm]

40-3/16"

[1021mm]

36-1/8"

[918mm]

FRONT VIEW

3/4"

GAS

INLET

12-5/8"

[321mm]

25-1/2"

[646mm]

AVERAGE

23"

[584mm]

MAX

44.03°

AVERAGE

[48° MAX]

33-25/32"

[858mm]

RIGHT SIDE VIEW

7" [178mm] MIN

11" [279mm] MAX

26-23/32"

[678mm]

FROM PLATEN

ARM PIVOT

50-1/2"

[1282mm]

AVERAGE

4-41/64"

[118mm]

1-23/32"

[44mm]

2-3/4"

[70mm]

25-7/8"

[656mm]

38-25/64"

[975mm]

Model

Total

kW

Load

Loading kW/Phase Nominal Amps Per Line

208/220/240V 3ph

208V 220V 240V

TB

1-Ph 3-Phase Delta 1-Ph 3-Phase Delta 1-Ph 3-Phase Delta

X-Y X-Z Y-Z L1-L2 X Y Z L1-L2 X Y Z L1-L2 X Y Z

XG36

12.99 4.00 4.99 4.00

1 41.63 37.43 33.30 37.43 39.36 35.38 31.49 35.38 36.08 32.43 28.90 32.43

2 20.82 – – – 19.68 – – – 18.04 – – –

XG36-2

L/R

8.66 2.66 3.33 2.66 1 41.63 24.93 22.14 24.93 39.36 23.57 20.94 23.57 36.08 21.61 19.19 21.61

XG36-1

L/C/R

4.33 1.33 1.66 1.33 1 20.82 12.46 11.07 12.46 19.68 11.78 10.47 11.78 18.04 10.80 9.59 10.80

XG36-F

1.00 – 1.00 – 1 1.00 4.16 – 4.16 1.00 3.90 – 3.90 1.00 3.60 – 3.60

NOTE: Model XG36 is not available for 1-phase wiring in Canada

Model

Total

kW

Load

Loading kW Per Phase Nominal Amps Per Line

380/400/415V 380V 400V 415V

L1/N L1/L2 L1/L3 L2/L3 L1/N L1 L2 L3 L1/N L1 L2 L3 L1/N L1 L2 L3

XG36CE

12.99 0.99 4.00 4.00 4.00 4.50 20.48 18.23 18.23 4.30 19.80 17.32 17.32 4.12 18.75 16.70 16.70

XG36CE-2

L/R

8.81 0.81 2.67 2.67 2.67 4.00 14.01 12.16 12.16 3.52 13.57 11.55 11.55 3.37 12.83 11.14 11.14

XG36CE-1

L/C/R

4.63 0.63 1.33 1.33 1.33 2.8 7.42 6.06 6.06 2.70 7.12 5.75 5.75 4.12 18.75 16.70 16.70

XG36CE-F

0.45 0.45 0.00 0.00 0.00 2.04 1.18 0.00 0.00 1.95 1.13 0.00 0.00 1.87 1.08 0.00 0.00

Clearances Gas Pressure

Total Input

Entry Installation Supply (min.) Operating

Crated Uncrated Sides Rear NAT PRO NAT PRO BTU/Hr kW

47-1/2"

(1207mm)

40-3/4"

(1035mm)

6"

(152mm)

3"

(76mm)

7.0" WC 11.0" WC 3.5" WC 3.5" WC 99,000 29.1

Part # 4517124 Rev. 7 (08/17/11)Page 6

SAFETY PRECAUTIONS

Always follow these safety precautions when operating the

Xpress Grill.

• THIS GRILL MUST be operated by persons who have

been given adequate training.

• THIS EQUIPMENT MUST ONLY BE OPERATED UNDER AN

APPROVED HOOD SYSTEM.

• DO NOT operate the grill without reading this operation

manual.

• DO NOT operate the Xpress grill unless all service and

access panels are in place and fastened properly.

The Garland Xpress Grill is a semi-automatic cooking

appliance. The upper platen is lowered automatically,

following the manual, two-handed initiation of the cooking

cycle, and the upper platen is raised automatically upon

completion of the cooking cycle.

When two sided cooking, the area between the upper platen

and the griddle plate should be regarded as a “danger zone.”

During two sided cooking the operator must not be within

this danger zone. When used as a at grill, then this area is no

longer a danger zone, the platens do not move.

For whatever reason, be it cleaning, maintenance, or normal

operation, any exposed person must use extreme caution if

within this danger zone.

In two side cooking the upper platen remains in the lowered

position by nature of its own weight. It is not locked down. It

can be raised by lifting up on the handle on the front of the

platen.

The Xpress Grill may during its operation emit airborne noise

equivalent to a continuous A weighted sound pressure level

of 73dB(A).

WARNING: To avoid serious personal injury:

• DO NOT attempt to repair or replace any part of the

Xpress Grill unless all main power supplies to the grill

have been disconnected.

• USE EXTREME CAUTION in setting up, operating and

cleaning the Xpress Grill to avoid coming in contact

with hot grill surfaces or hot grease. Suitable protective

clothing should be worn to prevent the risk of burns.

• DO NOT clean this appliance with a water jet.

• DO NOT apply ICE or COLD WATER to a HOT grill surface.

• NOTE all warning labels and markings axed to the grill.

WARNING: After turning the master power switch to the

START position, the grill will go through initialization. If

the upper platens are in the lowered position they will

return to their raised upper position. This movement takes

approximately 8 seconds.

INSTALLATION

IMPORTANT: Rating plate for this appliance is located on

the right side panel.

This equipment must be installed by a competent factory

trained, certied, licensed and / or authorized service or

installation person.

WARNING: This appliance must be properly grounded.

Prior to installation, the four casters, supplied loose with the

grill, must be securely located on the underside of the base.

The casters tted with a brake must be located at the front of

the grill.

This appliance should be connected to a potential

equalization system. A labeled equipotential bonding point

is tted to the rear of the grill.

It is recommended that this grill be connected to a residual

current,, (earth leakage),, device with a tripping current not

exceeding 30mA. The leakage current of this grill will not

exceed 5mA.

CAUTION: Prior to installation, check the electrical supply

to ensure input voltage and phase match the equipment

voltage rating and phase. See data plate located rear left side

of grill and lower front panel.

Part # 4517124 Rev. 7 (08/17/11) Page 7

INSTALLATION continued

Grill is to be located directly under ventilation system.

Once installed in the grill station underneath the ventilation

system, the platens, in their highest position, must not

interfere with the lower lip of the ventilation system hood.

The raised position of each platen is adjusted by raising

or lowering the upper of the two microswitches, (limit

switches), in the rear of the grill. The lower microswitch

position must not be adjusted.

Grill plate must be level front to back, side to side and

diagonally. This leveling must be done with the unit under

the hood and in it’s normal operational position to prevent

warping of the grill plate.

NOTE: Fuses are installed to prevent damage in the event of

failure of the upper microswitch.

Installation shall be made with the gas connector that has

been supplied loose with the grill. The quick disconnect

tting and gas shut o valve must be installed in the

direction indicated on their outer body.

NOTE: When checking gas pressure, be sure that all other

equipment on the same gas line is on.

The appliance and its individual shut-o valve must be

disconnected from the gas supply piping system during any

pressure testing of that system pressures in excess of ½ PSIG

(3.45kPa).

Adequate clearance must be provided for servicing and

proper operation.

National Codes Requirements:

The type of gas for which the grill is equipped is stamped on

the data plate on the inside rear of the unit and on the lower

front panel. Connect a grill stamped for Natural Gas only to

Natural Gas.

The installation must conform to the National Fuel Gas Code

ANSI Z223.1-1998 or latest edition, NFPA No. 54 – latest

edition and National Electrical Code ANSI/NFPA 70-1990 or

latest edition and/or local code to assure safe and ecient

operation. In Canada, the installation must comply with CSA

B149.1 and local codes where applicable

In Canada, electrical connection must comply with

applicable sections of the Canadian Electrical Code, C22.1

- 1990, latest edition, “Safety Standard for Installation,

Part 1” and C22.2- No. O-M 1982 latest edition , “General

Requirements, Part 2”.

Gas Connections, and Pipe Sizing:

The size of the gas line is very important. If the line is too

small, the gas pressure at the burner manifold will be low.

This will cause slow recovery and delayed ignition. The

incoming gas pressure line should be a minimum of 1-1/2".

All grills require a 3/4" connection.

Before connecting new pipe the pipe must be blown out to

dispose of any foreign particles. These particles will cause

improper operation.

When using thread compound, use small amounts on male

threads only. Use a compound that is not aected by the

chemical action of LP gases. Avoid applying compound

to the rst two threads to prevent clogging of the burner

orices and control valve.

Have the installer check all gas plumbing with a soap

solution for leaks. DO NOT USE matches, candles or other

ignition sources in checking for leaks.

The grill must be disconnected from the gas supply system

when pressure testing of that system at pressures in excess

of 2 psi.

Check the data plate to determine the proper type of gas

before connecting the quick disconnect or piping from the

building gas supply.

An incoming gas pressure test nipple is provided on the

incoming gas manifold for pressure checks.

Minimum incoming gas pressure for Natural Gas is 6" W.C.

Maximum incoming gas pressure for Natural Gas is 14" W.C.

Minimum incoming gas pressure for Propane is 10" W.C.

Maximum incoming gas pressure for Propane is 26" W.C.

Burner operating gas pressure can be checked at the outlet

side of the gas valve at the pressure test point.

Burner manifold pressure for Natural Gas must be 3.5" W.C.

Burner pressure for Propane must be 3.5" W.C.

To adjust the burner pressure, remove the sealing screw

from the pressure test nipple, connect a manometer, remove

the sealing cap on the gas valve regulator, turn on the grill,

adjust the screw in the regulator to give the correct pressure,

turn o the grill, ret the regulator sealing cap, remove the

manometer, replace the seal screw in the test nipple and test

for gas leaks.

Gas pressures should be checked by the local Gas Company

or an authorized service agency only.

Test all piping and connections for gas leaks. A rich soap

solution should be used for this purpose. Never use a ame.

Part # 4517124 Rev. 7 (08/17/11)Page 8

INSTALLATION continued

Appliances Equipped with Casters:

1. The installation shall be made with a connector that

complies with the Standard for Connectors for Moveable

Gas Appliances, ANSI Z21.69 or latest edition, addenda

Z21.69a-1989, and a quick-disconnect device that

complies with the Standard for Quick Disconnects for Use

with Gas Fuel. ANSI Z21.41 or latest edition.

2. The front casters on the appliance are equipped with

brakes to limit the movement of the appliance without

placing any strain on the connector or quick-disconnect

device or its associated piping.

3. Please be aware; required restraint is attached to a

bracket (which is located on the rear caster closest to the

gas connection), and if disconnection of the restraint

is necessary; be sure to reconnect the device after the

appliance has been returned to its original position.

Swivel Caster Installation

Prior to installation, the four casters, supplied loose with the

grill, must be securely located on the underside of the base.

The casters tted with a brake must be located at the front of

the grill.

1. Carefully remove the top and side packaging leaving the

grill on shipping pallet.

DO NOT REMOVE THE TIES SECURING THE PLATEN ARMS

TO THE GRILL TOWEL BAR.

2. Raise the grill vertically o the pallet to a comfortable

working height and install the casters. DO NOT TIP THE

GRILL ON ITS BACK OR SIDE. If a truck lift is used, be

careful when inserting the lifting arms under the grill as

the gas inlet elbow is protruding in the center of the base.

WARNING - GRILL WEIGHT IS APPROXIMATELY 800 LBS –

USE CAUTION

3. Install the casters as shown below. The two casters with

brakes go on the front, and the two without on the rear.

WITH

BRAKE

WITHOUT

BRAKE

NOTE: CASTERS MUST BE THREADED INTO GRILL BASE

LEAVING APPROXIMATELY ONE INCH OF EXPOSED

THREAD. THIS IS THE STARTING POINT FOR LEVELLING THE

GRILL AFTER IT IS IN POSITION.

Electrical Connections:

All electrically operated appliances must be electrically

grounded in accordance with local codes; or in the absence

of local codes, with the latest edition of National Wiring

Regulations. A wiring diagram is located on the rear panel of

the grill. See rating plate in rear of grill, or lower front panel

for proper voltages.

Ventilation and Clearance:

One of the most important considerations of ecient grill

operation is proper ventilation and air supply. Insure the

grill is installed so the products of combustion are removed

eciently and the ventilation system does not produce

drafts that interfere with proper burner operation.

Proper operation of exhaust fans (speed, rotation and

adjustment) is essential. In addition to the exhaust system

the make-up air system, (HVAC), for the kitchen is the

air supply for the combustion air for the burners. Proper

incoming air is essential for all gas operated equipment. Poor

incoming make-up will cause inecient burner operation,

delayed ignition and possible burner failure.

Any ventilation system will break down if improperly

maintained. The duct system, the hood, and the lters must

be cleaned on a regular basis and kept grease free.

The room containing the grill is required to have a

permanent air vent. The minimum eective area of the vent

shall be 0.7 in.² per kW. Air vents shall be of such a size to

compensate for the eects of any extract fan in the premises.

Part # 4517124 Rev. 7 (08/17/11) Page 9

Master Power Switch:

Controls power to the grill and must be turned “ON” to start

operation. The controller display will be active when the

switch is “ON”.

LED Indicators:

There are two, (2), indicator lights, indicating the

temperature status of each control’s heat zones; one, (1), on

the upper platen, (top light), and one, (1), on the grill surface.

Each light can display three, (3), dierent colors, indicating

temperature status for the corresponding zone.

Red: The zone is too hot, (more than 79°F/45°C over the set

temperature), or heat zone failure.

Amber: The zone is calling for heat.

Green: The zone is at or above the set temperature.

Display:

The controller display will contain information relevant to

each operation in both cook and program modes.

16-CHARACTER

2-LINE DISPLAY

PRODUCT

BUTTONS

LED

INDICATORS

POWER

BUTTON

PROGRAM

BUTTON

TEMPERATURE

BUTTON

ENTER

BUTTON

DOWN ARROW

BUTTON

UP ARROW

BUTTON

WHEN PUSHED SIMULTANEOUSLY:

"START COOK TIME COUNTDOWN" (flat grill cooking)

OR "LOWER PLATEN" (two-sided cooking)

MASTER

POWER

SWITCH

CANCEL/

RAISE PLATEN

BUTTON

GRILL CONTROLS

Product Buttons (1-8):

Buttons 9 and 0 are used for standby and clean. They also

can be used in programming to the cursor left or right when

creating or modifying product names in “PROD NAME LIB”

program mode.

Power Button:

After the main power switch is turned on, this button will put

the control into cook mode. If pressed again, the control will

go back to displaying “OFF.”

Program Button:

The primary function is to access Programming and

Calibration of the grill. Push and hold for ve (5) seconds.

Display will ask for the code. After entering code, ve

programming features will be accessible “MENU ITEMS,”

“SYSTEM INFO,” “SYSTEM SETUP,” “SERVICE MODE,” and

“PRODUCT NAME LIB.”

Part # 4517124 Rev. 7 (08/17/11)Page 10

GRILL CONTROLS continued

Temperature Button:

In the Cook mode, each time the button is pressed the

current temperature for one zone is displayed. The grill

temperature is displayed rst followed by the platen

temperature. After ve (5) seconds, the display will return

to the menu item selected. Pressing and holding the

temperature button for 5 seconds will display both the grill

and platen temperatures. To exit press the temperature

button.

Up/Down Arrow Buttons; 2 Functions:

1. In the cook mode, the Up/Down Arrow Buttons will cycle

through the dierent menu items.

2. In the program mode, the Up/Down Arrow Buttons will

change the value of the current setting.

Enter Button:

Function is to accept programming steps.

Cancel/Raise Platen Button, (Green):

During the cooking cycle, pressing this button will cancel the

cooking timer and return the grill to the “IDLE” mode. This

button will also bring the grill out of STANDBY.

Black Button:

When both Black and Green “CANCEL/RAISE” buttons are

pressed simultaneously, the upper platen will lower to the

griddle surface.

Part # 4517124 Rev. 7 (08/17/11) Page 11

Installing Release Material:

A release material sheet must be replaced when:

• Product sticks to release material.

• Carbon build-up ruins taste or appearance.

• Tearing occurs in the sheet’s cooking area.

• Release material coating is worn o sheet.

Slide release material rod through hemmed end of the

release material sheet.

Hook release material rod on brackets located at the rear of

the upper plate

Holding the bottom of the release material sheet in place,

gently pull the sheet toward the front of the platen.

UPPER PLATEN (side view)

RELEASE MATERIAL HOOK

RELEASE

MATERIAL ROD

RELEASE MATERIAL SHEET

REAR OF GRILL

Thread the front edge of the release material sheet behind

the release material bar on the front of the platen, then

around the top and down over the front of the bar as shown.

Place locking clips over release material sheet and press into

place over release material bar.

Check alignment and tightness of release material against

upper platen.

OPERATION

UPPER PLATEN (side view)

RELEASE

MATERIAL

BAR

RELEASE

MATERIAL

LOCKING

CLIP (1)

RELEASE

MATERIAL

FRONT OF GRILL

NOTE: Make sure release material ts smoothly over upper

platen. Installing release material sheets too tight may cause

premature failure of the sheet.

Release sheets are reversible and should be ipped over

and reattached on a daily basis. For instructions on cleaning

release sheets, see Step 17., under Daily Cleaning in Cleaning

and Maintenance section

Lighting Instructions:

1. Ensure that the exible gas hose is connected to the grill

and the power cord is plugged into the receptacles.

2. Turn the main power switch ON and allow the controls

to go through the power-up self-check. Once the control

panel displays the word “OFF” the unit is ready to begin

the heating process.

3. Press

.

The control will automatically initiate the

heating cycle. The burner will ignite and heat until the

temperature specied by the menu item has been

obtained.

If ignition of the burner does not occur on the rst trial, the

bottom indicator light will ash amber. If the burner(s) do

not light within four trials for ignition, the control will display

a ashing warning, “IGNITION ERROR.” The ashing amber

light will turn to solid red and an audible alarm will sound. If

this occurs, turn the main power switch o, wait 5 minutes,

and then repeat steps 2 and 3.

Part # 4517124 Rev. 7 (08/17/11)Page 12

Simplied Cook Cycle Instructions:

1. Press button to turn on mainpower to grill.

- - - - - - -

*** *

START

STOP

EMERGENCY

- - - - - - -

*** *

START

STOP

EMERGENCY

Press button to turn on main

power to grill.

Place item on grill surface and

select item number for that item to

be cooked.

Press both green and black buttons

to lower clam and begin cooking

product.

Press button to turn zone power on.

Clam Grill Operating Instructions

1

2

3.6 PAT TY

*** *

START

STOP

EMERGENCY

3.6 PAT TY

*** *

START

STOP

EMERGENCY

3

4

Press green button to cancel any

time during cook cycle.

- - - - - - -

*** *

START

STOP

EMERGENCY

5

NOTE: To avoid damage to controller use knuckle or flat part of finger

to press buttons. Do NOT use finger nails, tongs or spatulas

2. Press to turn zone power on.

- - - - - - -

** * *

START

STOP

EMERGENCY

- - - - - - -

** * *

START

STOP

EMERGENCY

Press button to turn on main

power to grill.

Place item on grill surface and

select item number for that item to

be cooked.

Press both green and black buttons

to lower clam and begin cooking

product.

Press button to turn zone power on.

Clam Grill Operating Instructions

1

2

3. 6 PAT T Y

** * *

START

STOP

EMERGENCY

3. 6 PAT T Y

** * *

START

STOP

EMERGENCY

3

4

Press green button to cancel any

time during cook cycle.

- - - - - - -

** * *

START

STOP

EMERGENCY

5

NOTE: To avoid damage to controller use knuckle or flat part of finger

to press buttons. Do NOT use finger nails, tongs or spatulas

3. Load product on grill surface and select the

corresponding product key.

- - - - - - -

** * *

START

STOP

EMERGENCY

- - - - - - -

** * *

START

STOP

EMERGENCY

Press button to turn on main

power to grill.

Place item on grill surface and

select item number for that item to

be cooked.

Press both green and black buttons

to lower clam and begin cooking

product.

Press button to turn zone power on.

Clam Grill Operating Instructions

1

2

3. 6 PAT T Y

** * *

START

STOP

EMERGENCY

3. 6 PAT T Y

** * *

START

STOP

EMERGENCY

3

4

Press green button to cancel any

time during cook cycle.

- - - - - - -

** * *

START

STOP

EMERGENCY

5

NOTE: To avoid damage to controller use knuckle or flat part of finger

to press buttons. Do NOT use finger nails, tongs or spatulas

4. Press both green and black buttons to lower clam and

begin cooking product.

- - - - - - -

** * *

START

STOP

EMERGENCY

- - - - - - -

** * *

START

STOP

EMERGENCY

Press button to turn on main

power to grill.

Place item on grill surface and

select item number for that item to

be cooked.

Press both green and black buttons

to lower clam and begin cooking

product.

Press button to turn zone power on.

Clam Grill Operating Instructions

1

2

3. 6 PAT T Y

** * *

START

STOP

EMERGENCY

3. 6 PAT T Y

** * *

START

STOP

EMERGENCY

3

4

Press green button to cancel any

time during cook cycle.

- - - - - - -

** * *

START

STOP

EMERGENCY

5

NOTE: To avoid damage to controller use knuckle or flat part of finger

to press buttons. Do NOT use finger nails, tongs or spatulas

OPERATION continued

5. Press green button to cancel any time during cook cycle.

- - - - - - -

** * *

START

STOP

EMERGENCY

- - - - - - -

** * *

START

STOP

EMERGENCY

Press button to turn on main

power to grill.

Place item on grill surface and

select item number for that item to

be cooked.

Press both green and black buttons

to lower clam and begin cooking

product.

Press button to turn zone power on.

Clam Grill Operating Instructions

1

2

3. 6 PAT T Y

** * *

START

STOP

EMERGENCY

3. 6 PAT T Y

** * *

START

STOP

EMERGENCY

3

4

Press green button to cancel any

time during cook cycle.

- - - - - - -

** * *

START

STOP

EMERGENCY

5

NOTE: To avoid damage to controller use knuckle or flat part of finger

to press buttons. Do NOT use finger nails, tongs or spatulas

To Cook in Two-Sided Mode:

1. To start a cook cycle select a product recipe by using the

product keys (1 through 9) or by using the UP/DOWN

keys

or to select a product recipe.

The display alternately blinks the recipe and the word

SELECTED 2 times then the recipe displays continuously.

2. The controller regulates the platen and grill temperatures

to the set temperatures of the product selected and

reads “TOO COOL” or “TOO HOT” with “MENU ITEM”, until

the grill attains the set temperature range for the item.

NOTE: If the display reads either “TOO COOL” or “TOO HOT”

the upper platen will not lower and initiate a cooking

sequence.

3 After loading the product onto the grill, press the green

CANCEL/RAISE PLATEN BUTTON and BLACK button

simultaneously. A cook cycle starts and the upper platen

lowers if the product selected is clamshell recipe.

4 To cancel a cook cycle at anytime press the green

CANCEL/RAISE PLATEN BUTTON and the upper platen

will rise if the product recipe selected is clamshell recipe.

5. During a cook cycle, the display shows the product recipe

name in the rst line and the remaining cook time count

down in the second line.

6 When the cook timer reaches one, (1), second remaining

a pre-time-out alarm sounds alerting the operator.

7 When the cooking time has been completed the platen

raises automatically. On the controller the “PRODUCT

NAME” and the word “REMOVE” will be displayed and an

audible alert will sound.

8. Pressing the green CANCEL/RAISE PLATEN BUTTON stops

the audible alert and the unit will revert back to IDLE

mode.

Part # 4517124 Rev. 7 (08/17/11) Page 13

To Cook in Flat Grill Mode:

1. To start a cook cycle select a product recipe by using the

product keys (1 through 9) or by using the UP/DOWN

keys

or

to select a product recipe.

The display alternately blinks the recipe and the word

SELECTED 2 times then the recipe will be displayed

continuously.

2. The controller regulates the grill temperature to the set

temperature of the product selected and reads “TOO

COOL” or “TOO HOT” with “MENU ITEM”, until the grill

attains the set temperature range for the item.

NOTE: If the display reads either “TOO COOL” or “TOO HOT” it

will not initiate a cooking sequence.

3 After loading the product onto the grill, press the green

CANCEL/RAISE PLATEN BUTTON and BLACK button

simultaneously. That will start a cook cycle if the product

selected is clamshell recipe.

4 To cancel a cook cycle at anytime the press the green

CANCEL/RAISE PLATEN BUTTON .

5. During a cook cycle, the display shows the product recipe

name in the rst line and the remaining cook time count

down in the second line.

6. The display shows the “SEAR” or “FLIP” alarm message

with ashing in the second line if the current cooking

product is at recipe and the sear time or ip time is not

zero.

7. A cook alarm sounds with a repeating beep pattern.

Pressing the black RAISE button acknowledges the “SEAR”

or “FLIP” alarm message if the alarm eld in system setup

is set to MANUAL.

8. The “SEAR” or “FLIP” alarm message stops after 5 seconds

if the alarm eld in system setup is set to AUTO.

9. When a cook is complete, the display shows the product

recipe name in the rst line and a ashing “REMOVE”

message in the second line. A repeating beeping alarm

also sounds.

10. Pressing the black RAISE button cancels the cook done

alarm.

11. The unit revertes back to IDLE mode.

OPERATION continued

Enter Standby Mode:

Stand by mode is used during slow periods to conserve

energy with out a complete shut down of the unit. When

cooking temperatures are again required, pre-heat cook

temperature/time is reduced. Stand by mode temperatures

can be adjusted, see the PROGRAMING section.

1. Select Standby Mode by pressing

or

until

“STANDBY” is displayed.

2. Press the GREEN (‘CANCEL/RAISE’) and the BLACK buttons

at the same time. As soon as the upper platen moves

down, the display will read “STANDBY MODE.” (Note: The

rst time Standby Mode is entered, the display prompts

the operator to press ENTER after pressing the GREEN

and BLACK buttons.)

Exit Standby Mode:

1. Press the GREEN (‘CANCEL/RAISE’) button. The upper

platen will raise and the display will read “CANCEL” with

an audible alarm.

To Display the Current Temperatures:

1. Press the button and repeat for each zone to be

displayed...

1st press - LOWER GRILL ZONE

2nd press - UPPER PLATEN

3rd Pressing and holding the button for 5 seconds

will display both the grill and platen temperatures (preset

and actual). Press again ) to exit.

NOTE: The temperatures may be displayed at any time,

including during a cooking cycle.

To View Settings for a Menu Item:

1. Enter Programming; Menu Items, (see Programming)

2. Press to enter “PROGRAMMING MODE MENU ITEMS”

3. Use and to choose the desired Menu Item.

4. Press

to scroll through settings for the chosen item.

To Clean the Grill:

1. To start a CLEAN MODE select the clean mode recipe by

pressing product key 10 or by using the UP/DOWN keys

or to select the clean mode recipe.

2. The controller regulates the platen and grill temperatures

to the set temperatures of the clean mode recipe. The

display shows the message “CLEAN MODE” in the rst line

and the actual grill temperature in the second line.

Part # 4517124 Rev. 7 (08/17/11)Page 14

CLEANING AND MAINTENANCE

Cleaning During Operation:

1. After each product load is removed, Use a grill scraper to

scrape grease on lower grill plate from front to back only.

Do not scrape left to right across the lower grill plate with

the grill scraper.

2. Use a grill squeegee to clean release material sheet on

upper platen in a downward motion. Do not press hard

against the release material sheet to prevent scratching

or tearing.

3. Push the grease to the rear of the grill, or pull it to the

front trough. Then, squeegee the grease into the buckets

on either side. Do not use the scraper for this step.

4. Use a clean, damp cloth to clean back splash and

bullnose areas as needed during operation.

Note: To increase life of release material sheets, wipe them

down with a folded clean, damp cloth at least four times

during each hour of operation.

3. Press the ENTER key

to initiate the clean mode.

4. The display SHOWS the message “READY TO CLEAN” with

ashing in the second line when the actual temperature

is reached (or greater than the set temperatures of clean

mode recipe (default 220°F or 250° for both the platen

and grill)). A 5 second repeating beep pattern is sounded.

5. Press the ENTER key

again, the heater’s control for the

platen and grill are turned o and the display shows the

message “CLEANING” with ashing in the second line.

6. Press the ENTER key again to exit the CLEAN MODE. The

display shows the message “STANDBY” in the rst line.

The control transitions to “STANDBY MODE” and preheats

to idle condition.

PLATEN SET:

This function allows the platen to be moved up or down

once it is parallel to the grill surface. Values range from –160

to +160.

OPERATION continued

EXTENDED TIME:

This option will add 6, 4 and 2 seconds to the time of the next

three cooks respectively if the grill has had no activity for

5 minutes. Provided the temperature is not 25°F above set

temperature for either the grill or the platen.

INSTANT ON TIME:

This can be set in the range of 00:00 to 00:40. Instant on will

turn on the heat zone(s) as soon as a cook cycle starts.

START DELAY:

This number is how long the operator must hold the GREEN

(‘CANCEL/RAISE’) and BLACK buttons to start a cooking cycle

for 2-sided recipes only. There will be one beep when the

cook is started and another beep when the START DELAY

time is reached. If the GREEN (‘CANCEL/RAISE’) and BLACK

buttons are released before that time the cook will be

canceled. If Yes is toggled press enter to allow the user to

pick from 1 to 5 seconds in 0.5 second increments using

and .

Daily Cleaning:

Warning: The upper platen surface and edges are very hot! To prevent burn injuries, use extreme caution when wiping

down release sheets and platen edges.

Grill Squeegee

Grill Cleaning Pad & Handle Grill Scraper

Heat-Resistant Gloves Clean, Sanitizer-Soaked

Grill Cloths

High-Temperature

Grill Cleaner

Part # 4517124 Rev. 7 (08/17/11) Page 15

• Select Clean Mode

When Clean Mode has

been reached, the LED

indicators will turn GREEN.

• Wipe the Release

Material sheets with a

clean,sanitizer-soaked

grill cloth.

• Remove the locking clips,

bars, and release sheets.

Wash, rinse, and set aside

to dry.

• Set release sheets aside

on a at surface.

• Scrape the lower grill

surface with the scraper.

• Use the grill squeegee to

push residual grease into

trough.

• Wash and rinse the

squeegee and scraper.

CLEANING AND MAINTENANCE continued

04

03

01

02

05

07

08

• Remove the grease trough

from each side. Empty and

replace.

• Apply the grill cleaner

to front side of platens

starting from right platen

to left platen.

• DO NOT SCRUB.

• Apply the grill cleaner to

platen surfaces starting

from right platen to left

platen.

• DO NOT SCRUB

• Apply the grill cleaner to

back side of platens from

right platen to left platen.

• DO NOT SCRUB

06

09

• Apply the grill cleaner to

outer edges of right and

left platens.

• DO NOT SCRUB

• Press green & black

buttons to lower the

center platen.

• Apply grill cleaner to

inner edges of the right

and left platens, and

the edges of the center

platen.

• DO NOT SCRUB

• Press green button to

raise center platen..

• Apply grill cleaner to

bottom grill surface.

• Spread the cleaner over

the entire lower grill

surface from front to back

using even strokes.

• DO NOT SCRUB

• Rinse platen surfaces with

a clean, sanitizer-soaked

grill cloth, starting from

right to left platens.

• Press green & black

buttons to lower the

center platen.

10

11

12

Part # 4517124 Rev. 7 (08/17/11)Page 16

CLEANING AND MAINTENANCE continued

PLATEN ZEROING

Turn Master power switch “ON”, wait for controllers to display

“OFF”.

Note: Release sheets should not be installed during this

procedure.

1. Press and hold for three, (3) seconds. “ENTER CODE” is

displayed.

2. Using the Product buttons, 0-9

enter the code, (1251).

“ENTER CODE **** ” is displayed.

3. Press

to enter the Programming Mode.

“PROGRAMMING MODE MENU ITEMS” is displayed.

4. Press

two, (2) times in succession to display

“PROGRAMMING MODE SYSTEM SETUP.”

5. Press

eight, (8) times. “PLATEN SET +/- XX” is displayed.

(XX=numbers that will vary from grill to grill.)

6. Allow time for grill to heat and turn ready. Press

both the Cancel (Green) and Standby (Black) buttons

simultaneously to lower the upper platen. Press the

• Rinse the edges of all three

platens.

• Press green button to raise

center platen.

• Pour a small amount of

lukewarm water on a

clean, sanitizer-soaked

grill cloth over the

bottom grill surface and

wipe o residue.

• Place upper platen

release material sheets

 at on the lower grill

surface.

• Gently clean both sides

of the release material

sheets with the grill

cleaning pad

• Rinse both sides of

the release material

sheets with a clean,

sanitizersoaked grill cloth.

• Reinstall the release

material sheets. Secure in

place with bars and clips

13

14

15

16

17

18

19

20

• Wipe lower grill with a

clean,sanitizer-soaked

grill cloth. Repeat until no

visible soil remains.

• Empty, wash, rinse,

and replace the grease

troughs.

• Wipe remaining grill

surfaces with a clean,

sanitizer-soaked grill

cloth.

• Apply a thin coat of fresh

shortening to the lower

grill surface only..

Part # 4517124 Rev. 7 (08/17/11) Page 17

11. Next go to the left rear adjuster and raise the platen until

the gapping tool ts snugly between the upper platen

and grill surface.

12. Move next to the right front adjustment and raise the

platen until the gapping tool ts snugly between the

upper platen and grill surface.

13. Repeat steps 9-12 one or more times until gapping tool

ts snugly between the upper platen and grill surface at

all four adjustment points without further adjustment.

(See diagram below.)

14. Replace the platen adjuster locking caps “hollow side

down” and tighten snugly. Replace platen adjuster caps.

15. Repeat steps 9-14 for each platen.

Teflon Release Material Sheet - 1799303

(one per platen)

ACCESSORIES

Teflon Release Material Rod - 4517008

(one per platen; 3 shown)

Teflon Release Material Clip - 1851301

(one per platen; 3 shown)

PLATEN ZEROING

Cancel (Green) button to raise the platen. Now, press both

the Cancel (Green) and (Black) Buttons to re-lower the

platen.

7. Remove platen adjuster caps from all four adjustment

points on each platen. Remove the four locking caps from

the adjustment points.

8. Using the adjusting tool lower platen until adjusting tool

touches the arm assembly.

9. With gapping tool, adjust right rear of platen until the

gapping tool ts snugly between the upper platen and

grill surface.

10. Move next to the left front adjuster and raise the platen

until the gapping tool ts snugly between the upper

platen and grill surface.

Part # 4517124 Rev. 7 (08/17/11)Page 18

“No-Go”

“Go”

Platen Gapping Tool -1838701

Insert gap tool directly below platen adjusters.

Grill Squeegee - 1868201

ACCESSORIES

Part # 4517124 Rev. 7 (08/17/11) Page 19

Raise

Back

Right

Lower

Front

Left

Platen leveling should be done from one corner

to the opposite corner. The adjuster nuts should

be turned opposite of one another.

Platen Adj Lock Nut - 1859103

Shoulder Bolt - 8005401

Platen Adjuster Nut - 1859101

Platen Adjuster Cap - 1859102

Use this end to turn all slotted

adjuster caps and nuts

Platen Adjusting Tool - 4523323

PLATEN ZEROING continued

Part # 4517124 Rev. 7 (08/17/11)Page 20

PROGRAMMING

Programming Modes/Menu Sequence:

Service Mode

System Set-up

System Information

UPPER SET TEMP

PLATEN GAP SET

GRILL SET TEMP

22

23

24

25

26

27

28

29

28

La page charge ...

Garland MST54 Mode d'emploi

Garland MST54 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents