Axial AXI03000B Le manuel du propriétaire

Catégorie
Jouets télécommandés
Taper
Le manuel du propriétaire

Ce manuel convient également à

INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
MANUEL D’UTILISATION
MANUALE DI ISTRUZIONI
AXI03000
2
EN
Age Recommendation: Not for children under 14 years. This is not a toy.
WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the
product correctly can result in damage to the product, personal property and cause serious injury.
This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to
operate this Product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for
use by children without direct adult supervision. Do not use with incompatible components or alter this product in any way outside of the instructions
provided by Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the
instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.
NOTICE
All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product
literature, visit horizonhobby.com or towerhobbies.com and click on the support or resources tab for this product.
MEANING OF SPECIAL LANGUAGE
The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:
WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a
high probability of superfi cial injury.
CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.
NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no possibility of injury.
As the user of this product, you are solely responsible for operating in a manner that does not endanger yourself and others or result in damage to the
product or property of others.
This model is controlled by a radio signal subject to interference from many sources outside your control. This interference can cause momentary loss of
control, so it is advisable to always keep a safe distance in all directions around your model as this margin will help avoid collisions or injury.
Never operate your model with low transmitter batteries.
Always operate your model in open spaces away from full-size vehicles,
traffi c and people.
Never operate the model in the street or in populated areas for any reason.
Carefully follow the directions and warnings for this and any optional
support equipment (chargers, rechargeable battery packs, etc.) you use.
Keep all chemicals, small parts and anything electrical out of the reach
of children.
Never lick or place any portion of the model in your mouth as it could
cause serious injury or even death.
Exercise caution when using tools and sharp instruments.
Take care during maintenance as some parts may have sharp edges.
Immediately after using your model, do NOT touch equipment such as
the motor, electronic speed control and battery, because they generate
high temperatures. You may burn yourself seriously touching them.
Do not put fi ngers or any objects inside rotating and moving parts, as this
may cause damage or serious injury.
Always turn on your transmitter before you turn on the receiver in the
car. Always turn off the receiver before turning your transmitter off.
Keep the wheels of the model off the ground when checking the
operation of the radio equipment.
SAFETY PRECAUTIONS AND WARNINGS
WARNING AGAINST COUNTERFEIT PRODUCTS: Always purchase from a Horizon Hobby, LLC authorized dealer to ensure authentic
high-quality Spektrum product. Horizon Hobby, LLC disclaims all support and warranty with regards, but not limited to, compatibility and
performance of counterfeit products or products claiming compatibility with Spektrum technology.
3
EN
Your new Horizon Hobby vehicle has been designed and built with a
combination of waterproof and water-resistant components to allow you to
operate the product in many “wet conditions,” including puddles, creeks,
wet grass, snow and even rain.
While the entire vehicle is highly water-resistant, it is not completely
waterproof and your vehicle should NOT be treated like a submarine. The
various electronic components used in the vehicle, such as the Electronic
Speed Control (ESC), servo(s) and receiver are waterproof, however, most
of the mechanical components are water-resistant and should not be
submerged.
Metal parts, including the bearings, hinge pins, screws and nuts, as well
as the contacts in the electrical cables, will be susceptible to corrosion if
additional maintenance is not performed after running in wet conditions.
To maximize the long-term performance of your vehicle and to keep
the warranty intact, the procedures described in the “Wet Conditions
Maintenance” section below must be performed regularly if you choose
to run in wet conditions. If you are not willing to perform the additional
care and maintenance required, then you should not operate the vehicle in
those conditions.
CAUTION: Failure to exercise caution while using this product
and complying with the following precautions could result in
product malfunction and/or void the warranty.
GENERAL PRECAUTIONS
Read through the wet conditions maintenance procedures and make sure
that you have all the tools you will need to properly maintain your vehicle.
Not all batteries can be used in wet conditions. Consult the battery
manufacturer before use. Caution should be taken when using Li-Po
batteries in wet conditions.
Most transmitters are not water-resistant. Consult your transmitter’s
manual or the manufacturer before operation.
Never operate your transmitter or vehicle where lightning may be present.
Do not operate your vehicle where it could come in contact with salt
water (ocean water or water on salt-covered roads), contaminated or
polluted water. Salt water is very conductive and highly corrosive, so
use caution.
Even minimal water contact can reduce the life of your motor if it
has not been certifi ed as water-resistant or waterproof. If the motor
becomes excessively wet, apply very light throttle until the water is
mostly removed from the motor. Running a wet motor at high speeds may
rapidly damage the motor.
Driving in wet conditions can reduce the life of the motor. The additional
resistance of operating in water causes excess strain. Alter the gear ratio
by using a smaller pinion or larger spur gear. This will increase torque (and
motor life) when running in mud, deeper puddles, or any wet conditions
that will increase the load on the motor for an extended period of time.
WET CONDITIONS MAINTENANCE
Drain any water that has collected in the tires by spinning them at high
speed. With the body removed, place the vehicle upside down and pull full
throttle for a few short bursts until the water has been removed.
CAUTION: Always keep hands, fi ngers, tools and any loose or
hanging objects away from rotating parts when performing the
above drying technique.
Remove the battery pack(s) and dry the contacts. If you have an air
compressor or a can of compressed air, blow out any water that may be
inside the recessed connector housing.
Remove the tires/wheels from the vehicle and gently rinse the mud and
dirt off with a garden hose. Avoid rinsing the bearings and transmission.
NOTICE: Never use a pressure washer to clean your vehicle.
Use an air compressor or a can of compressed air to dry the vehicle and
help remove any water that may have gotten into small crevices or corners.
Spray the bearings, drive train, fasteners and other metal parts with a
water-displacing light oil. Do not spray the motor.
Let the vehicle air dry before you store it. Water (and oil) may continue
to drip for a few hours.
Increase the frequency of disassembly, inspection and lubrication of the
following:
- Front and rear axle hub assembly bearings.
- All transmission cases, gears and differentials.
- Motor—clean with an aerosol motor cleaner and re-oil the bushings
with lightweight motor oil.
WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS
TABLE OF CONTENTS
Water-resistant Vehicle with Waterproof Electronics ..................................... 3
box Contents ............................................................................................................4
Required Equipment ............................................................................................... 4
recommended tools ................................................................................................ 4
Getting started checklist........................................................................................5
Vehicle parts ............................................................................................................ 5
Charge the vehicle battery .................................................................................... 6
Install the transmitter batteries ............................................................................ 6
Transmitter functions ............................................................................................. 6
Install the vehicle battery ...................................................................................... 7
Binding ......................................................................................................................8
Range-checking the radio system ....................................................................... 8
Using the DIG transmission ................................................................................... 8
vehicle maintenance ..............................................................................................9
AE-5L Forward/reverse ESC with drag brake ..................................................10
Troubleshooting .....................................................................................................10
Notes .......................................................................................................................11
Limited Warranty ................................................................................................... 12
Warranty and Service Contact Information .....................................................12
FCC Information ..................................................................................................... 13
IC Information ........................................................................................................13
Compliance Information for the European Union ............................................ 13
Exploded Views .....................................................................................................50
Parts Lists ............................................................................................................... 54
Electronics ............................................................................................................ 55
4
EN
BOX CONTENTS
• Parts Bag
• Cross Wrench
(4) AA Alkaline batteries
• Hex Drivers
(1.5, 2.0, 2.5mm)
• Hobby
Knife
• Side Cutter • Curved
Scissors
• Long-nose Plier
REQUIRED EQUIPMENT
RECOMMENDED TOOLS
Battery charger compatible with
the chosen vehicle battery
2-3S Shorty LiPo Battery
(96mm maximum width, IC3
Connector Required)
• STX3
3Ch 2.4GHz FHSS Radio Transmitter (SPMSTX300)
(4) AA Alkaline batteries
• Capra
1.9 Unlimited Trail Buggy RTR
- 35T Electric Motor (AX31312)
- SRX300 3CH Receiver (SPMSRX300)
- S614 Metal Gear Servo 23T WP (SPMS614)
- AE-5L ESC w/LED Ports and Lights
(DYNS2213)
5
EN
Steering Servo
Steering Knuckle
Battery Tray
Transmission
Driveshaft
Upper 4-link Bar
ESC Plug
Electronic Speed Control (ESC)
Motor
Lower 4-link Bar
Shock Absorber
VEHICLE PARTS
GETTING STARTED CHECKLIST
Read the manual
Familiarize yourself with the vehicle and its components
Check all screws, especially the driveshaft setscrews, for tightness
from the factory
Charge the vehicle battery
Install 4 AA batteries in the transmitter
Power on the transmitter
Install the vehicle battery in the vehicle
Check for proper function of the throttle and steering
Range check the radio system
Drive the vehicle, challenge yourself and have FUN!
Perform any necessary vehicle maintenance
Steering Link
Dig Servo
Locked Differential
(inside axle housing)
Receiver Box
6
EN
INSTALL THE TRANSMITTER BATTERIES
TRANSMITTER FUNCTIONS
This transmitter requires 4 AA batteries.
1. Remove the battery cover from the transmitter.
2. Install the batteries as shown.
3. Install the battery cover.
CAUTION: NEVER remove the transmitter batteries while the model
is powered on. Loss of model control, damage, or injury may occur.
CAUTION: If using rechargeable batteries, charge only rechargeable
batteries. Charging non-rechargeable batteries may cause the
batteries to burst, resulting in injury to persons and/or damage to property.
CAUTION: Risk of explosion if battery is replaced by an incorrect
type. Dispose of used batteries according to national regulations.
2.4GHZ DIGITAL
RADIO SYSTEM
Top
Bottom
A. Servo Reversing
To reverse the Throttle (TH) or Steering (ST) channel, switch the position
of the correlating switch—“N” is for normal, “R” is for reverse.
B. Throttle Trim
Adjusts the throttle neutral point
C. Steering Trim
Adjusts the steering center point. Normally, the steering trim is adjusted
until the vehicle tracks straight.
D. Throttle Rate
Adjusts the end point of the throttle
E. Steering Rate
Adjusts the end point of the steering
F. Indicator Lights
Solid red lights: Indicates radio connectivity and adequate battery
power
Flashing red lights: Indicates the battery voltage is critically low.
Replace batteries
G. Throttle Limit
Limits throttle output to 50/75/100%
Select 50% or 75% for less experienced drivers or when you are driving
the vehicle in a small area.
H. Antenna
I. Power Button
J. Throttle/Brake
K. Steering Wheel
L. Channel 3 Buttons: Top and Bottom
A
B
D
F
E
G
J
H
K
C
I
L
Follow the manufacturer’s directions for your charger to properly charge
the vehicle battery.
CAUTION: Only use chargers designed to charge the chosen
battery type. Using an incompatible charger or incorrect charge
settings could result in fi re causing person injury or property damage.
CHARGE THE VEHICLE BATTERY
SETTING TRAVEL ENDPOINTS FOR CHANNEL 3
Follow the instructions below to set the travel endpoint of an accessory or servo on channel 3 if needed:
1. Press and hold the CH 3 “Top” button, while powering ON the
transmitter. Continue to hold the Top button until the transmitter LED
ashes 5 times.
2. Release the Top button
3. Use the CH3 Top and Bottom buttons to adjust the accessory or servo
to the desired fi rst end point position.
4. Turn the steering wheel fully clockwise (right) to confi rm the fi rst position.
The LED will fl ash once to confi rm the fi rst position has been saved.
5. Use the CH3 Top and Bottom buttons to adjust the accessory or servo
to the desired second end point position.
6. Turn the steering wheel clockwise (right) to confi rm the second
position. The LED will fl ash twice to confi rm the second position has
been saved.
7. Power off the transmitter to save the settings
7
EN
NOTICE: Power to the vehicle is controlled by connecting and
disconnecting the battery from the ESC. Always power on the transmitter
rst before connecting the vehicle battery. Always disconnect the
battery from the ESC when not in use.
2. Remove the body clips and open the hood.
3. Connect the battery to the ESC. Close the
hood and replace the body clips.
NOTICE: Always disconnect the battery from
the ESC before powering off the transmitter.
Powering off the transmitter fi rst may result in
loss of control.
1. Power on the transmitter.
INSTALL THE VEHICLE BATTERY
8
EN
BINDING
Bind Port
Ch 3 Top
Ch 3 Bottom
The radio system should be checked before operating the vehicle to ensure proper operation and adequate range.
1. Turn on the transmitter.
2. Connect the battery in the vehicle.
3. Have a friend hold the vehicle while keeping hands and loose clothing away from moving parts.
4. Walk away until you are at the maximum planned operating distance from the vehicle.
5. Turn the steering wheel side to side and operate the throttle, both forward and reverse, checking for any erratic behavior.
6. If any erratic behavior is exhibited, DO NOT operate the vehicle. Call customer service for assistance.
RANGE-CHECKING THE RADIO SYSTEM
Binding is the process of programming the receiver to recognize the
GUID (Globally Unique Identifi er) code of a single specifi c transmitter. The
STX3™ transmitter and SPMSRX300 receiver are bound at the factory. If
you need to rebind, follow the instructions below.
1. Insert the bind plug in the BIND port on the receiver.
2. Connect a fully charged battery pack to the ESC.
3. Power on the ESC. The red receiver LED fl ashes, indicating the
receiver is in bind mode.
4. Center the ST TRIM and TH TRIM dials on the transmitter.
5. Turn and hold the steering wheel fully right, then power the transmitter
on.
6. When the receiver LED stops fl ashing, release the steering wheel.
7. Remove the bind plug, then power off the receiver to save the settings.
8. Power off the transmitter.
9. Store the bind plug in a convenient place.
You must rebind when:
Different failsafe positions are desired e.g., when throttle or steering
reversing has been changed.
Binding the receiver to a different transmitter.
The Axial Capra includes a “Dig” transmission which allows the rear
axle to lock while still allowing the front wheels to spin. Use this feature
in close quarters to turn the vehicle tighter than is possible with normal
4 wheel drive or to preload the suspension when needed.
To use the Dig function:
1. Press the channel 3 “Top” button on the transmitter. The Dig function
engages, locking the rear axle.
2. Advance the throttle and turn the steering wheel left or right to tightly
pivot the vehicle around.
3. Press the channel 3 “Bottom” button to disengage the Dig function.
USING THE DIG TRANSMISSION
9
EN
Replace any
noticeable bent or
broken parts
Check the wheel nuts
for tightness
If applicable, check
the slipper clutch for
proper operation
Check for wear on
the ball joints in
the steering and
suspension links
(replace if necessary)
Ensure the wheel
beads are still fi rmly
bonded around the
entire circumference
of the rim
Check the receiver
antenna for damage
Check driveshaft
set screws and
apply thread
locking compound if
necessary
Keep the chassis free
of dirt and debris
Check the steering
operation for any
binding
Inspect shock
absorbers for smooth
dampened operation
Check for loose
screws on the chassis,
especially the knuckle,
C-hub and axle lockout
screws
Inspect the spur
and pinion gears for
damage
Check for any loose
connections or frayed
wiring
Check the driveline
for smooth, bind free
operation
Replace the
transmitter batteries
when indicated by
the transmitter, as
described in the
Transmitter Functions
section
Just like a full size car or truck your RC vehicle must undergo periodic maintenance in order to ensure peak performance. Preventative maintenance will
also help avoid needless breakages which could result in costly repairs. Below are some suggestions to properly maintain your vehicle.
VEHICLE MAINTENANCE
10
EN
TROUBLESHOOTING
Battery ESC
Red
Black
Motor
PROBLEM POSSIBLE CAUSE SOLUTION
Vehicle does not move
Batteries are not installed properly in the
transmitter
Ensure the transmitter batteries are properly installed
Weak or no battery in the vehicle Install a freshly charged vehicle battery
Damaged motor Replace the motor
Frayed or broken wiring Replace any damaged wiring
ESC is shut down by heat protection circuit Allow the ESC to cool down completely
Loss of vehicle control
Improper antenna placement
Ensure the transmitter antenna is not blocked and the receiver
antenna is located properly
Weak or no batteries in the transmitter or
vehicle
Install a freshly charged vehicle battery and new transmitter
batteries
Neutral or trim position is incorrect Adjust the steering trim
Receiver and/or battery not connected
properly
Check all receiver and battery connections
Steering and/or throttle function is reversed
Servo travel is reversed at the transmitter Set the transmitter servo reversing switch to the correct position
Motor wires are not connected properly Check all motor wires for correct polarity and secure connection
AE-5L FORWARD/REVERSE ESC WITH DRAG BRAKE
SETUP
Throttle calibration should not be needed out of the box. However, in order
to make the throttle range of different transmitters, the calibration of the
ESC is necessary:
Mount the ESC in an area that is well ventilated and isolated from
vibration and shock.
Connect the ESC motor wires to the motor red-to-red and black-to-black.
Plug the receiver into the throttle channel of the receiver.
Before plugging the battery into the ESC, make sure your transmitter is
on and the throttle trim is set to zero.
Connect the battery to the ESC. The vehicle will be powered on when the
battery is connected.
CAUTION: Keep all body parts and loose clothing away from any
moving parts while the battery is connected to the ESC.
CAUTION: Always connect the ESC only to a proper power
source that has the correct voltage and polarity. Incorrect
voltages or reversed polarity will damage the ESC. Damage to the ESC
caused by improper voltage or polarity is not covered under warranty.
Test forward and reverse control using the transmitter.
To calibrate the ESC:
Power the transmitter on and set the throttle control to neutral.
Connect the battery to the ESC and wait 3 seconds to let the ESC initiate
a self-test and automatic throttle calibration.
• The ESC is ready to run when a long beep sound is emitted from the motor.
Always disconnect the battery when the vehicle is not in use.
NOTES
The drag brake is set to 100% from the factory.
The LiPo cut-off is set to “ON” from the factory.
ESC SPECIFICATIONS
Input Voltage 2-3S LiPo, 5-9 Cells NiMH/NiCd
Size 46.5mm x 34mm x 28.5mm
Weight 70g
Motor Limit 12T 2S/18T 3S
On-Resistance FET .002
Rated/Peak Current 180A
Braking Current 90A
BEC Voltage/A 6.0V 3.0A Peak
PWM Frequency 1KHz
ESC SOUND STATUS
1 Short Beep Battery is NiMH/NiCd
2 Short Beeps Battery is 2S LiPo
3 Short Beeps Battery is 3S LiPo
1 Long Beep
Self-test and throttle calibration
is OK and ESC is ready to run
To Receiver
Throttle Channel
11
EN
NOTES
12
EN
What this Warranty Covers
Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the
product purchased (the “Product”) will be free from defects in materials
and workmanship for a period of 2 years from the date of purchase.
What is Not Covered
This warranty is not transferable and does not cover (i) cosmetic damage,
(ii) damage due to acts of God, accident, misuse, abuse, negligence,
commercial use, or due to improper use, installation, operation or
maintenance, (iii) modifi cation of or to any part of the Product, (iv) attempted
service by anyone other than a Horizon Hobby authorized service center, (v)
Product not purchased from an authorized Horizon dealer, or (vi) Product not
compliant with applicable technical regulations or (vii) use that violates any
applicable laws, rules, or regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO
OTHER WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS
ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT
LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE
PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED
THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE
PURCHASER’S INTENDED USE.
Purchasers Remedy
Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall
be that Horizon will, at its option, either (i) service, or (ii) replace, any
Product determined by Horizon to be defective. Horizon reserves the right
to inspect any and all Product(s) involved in a warranty claim. Service
or replacement decisions are at the sole discretion of Horizon. Proof of
purchase is required for all warranty claims. SERVICE OR REPLACEMENT
AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER’S SOLE AND
EXCLUSIVE REMEDY.
Limitation of Liability
HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL
OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION
OR COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH
CLAIM IS BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT
LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in
no event shall the liability of Horizon exceed the individual price of the
Product on which liability is asserted. As Horizon has no control over use,
setup, fi nal assembly, modifi cation or misuse, no liability shall be assumed
nor accepted for any resulting damage or injury. By the act of use, setup
or assembly, the user accepts all resulting liability. If you as the purchaser
or user are not prepared to accept the liability associated with the use of
the Product, purchaser is advised to return the Product immediately in new
and unused condition to the place of purchase.
Law
These terms are governed by Illinois law (without regard to confl ict of law
principals). This warranty gives you specifi c legal rights, and you may also
have other rights which vary from state to state. Horizon reserves the right to
change or modify this warranty at any time without notice.
WARRANTY SERVICES
Questions, Assistance, and Services
Your local hobby store and/or place of purchase cannot provide warranty
support or service. Once assembly, setup or use of the Product has been
started, you must contact your local distributor or Horizon directly. This
will enable Horizon to better answer your questions and service you in
the event that you may need any assistance. For questions or assistance,
please visit our website at www.horizonhobby.com, submit a Product
Support Inquiry, or call the toll free telephone number referenced in the
Warranty and Service Contact Information section to speak with a Product
Support representative.
Inspection or Services
If this Product needs to be inspected or serviced and is compliant in the
country you live and use the Product in, please use the Horizon Online
Service Request submission process found on our website or call Horizon
to obtain a Return Merchandise Authorization (RMA) number. Pack the
Product securely using a shipping carton. Please note that original boxes
may be included, but are not designed to withstand the rigors of shipping
without additional protection. Ship via a carrier that provides tracking
and insurance for lost or damaged parcels, as Horizon is not responsible
for merchandise until it arrives and is accepted at our facility. An Online
Service Request is available at http://www.horizonhobby.com/content/
service-center_render-service-center. If you do not have internet access,
please contact Horizon Product Support to obtain a RMA number along
with instructions for submitting your product for service. When calling
Horizon, you will be asked to provide your complete name, street address,
email address and phone number where you can be reached during
business hours. When sending product into Horizon, please include
your RMA number, a list of the included items, and a brief summary of
the problem. A copy of your original sales receipt must be included for
warranty consideration. Be sure your name, address, and RMA number are
clearly written on the outside of the shipping carton.
NOTICE: Do not ship Li-Po batteries to Horizon. If you have any issue
with a Li-Po battery, please contact the appropriate Horizon Product
Support offi ce.
Warranty Requirements
For Warranty consideration, you must include your original sales receipt
verifying the proof-of-purchase date. Provided warranty conditions have
been met, your Product will be serviced or replaced free of charge.
Service or replacement decisions are at the sole discretion of Horizon.
Non-Warranty Service
Should your service not be covered by warranty, service will be completed
and payment will be required without notifi cation or estimate of the
expense unless the expense exceeds 50% of the retail purchase cost. By
submitting the item for service you are agreeing to payment of the service
without notifi cation. Service estimates are available upon request. You
must include this request with your item submitted for service. Non-
warranty service estimates will be billed a minimum of 1/2 hour of labor. In
addition you will be billed for return freight. Horizon accepts money orders
and cashier’s checks, as well as Visa, MasterCard, American Express,
and Discover cards. By submitting any item to Horizon for service, you are
agreeing to Horizon’s Terms and Conditions found on our website http://
www.horizonhobby.com/content/service-center_render-service-center.
ATTENTION: Horizon service is limited to Product compliant in the
country of use and ownership. If received, a non-compliant Product will
not be serviced. Further, the sender will be responsible for arranging
return shipment of the un-serviced Product, through a carrier of the
sender’s choice and at the sender’s expense. Horizon will hold non-
compliant Product for a period of 60 days from notifi cation, after which
it will be discarded.
10/15
Country of Purchase Horizon Hobby Contact Information Address
United States of America
Horizon Service Center
(Repairs and Repair Requests)
servicecenter.horizonhobby.com/RequestForm/
2904 Research Rd
Champaign, IL 61822
Horizon Product Support
(Product Technical Assistance)
productsupport@horizonhobby.com
877-504-0233
Sales
websales@horizonhobby.com
800-338-4639
European Union
Horizon Technischer Service service@horizonhobby.eu
Hanskampring 9
D 22885 Barsbüttel, Germany
Sales: Horizon Hobby GmbH +49 (0) 4121 2655 100
LIMITED WARRANTY
WARRANTY AND SERVICE CONTACT INFORMATION
13
EN
INSTRUCTIONS FOR DISPOSAL OF WEEE BY USERS IN THE EUROPEAN UNION
This product must not be disposed of with other waste. Instead, it is the user’s responsibility to dispose of their waste equipment by handing it
over to a designated collections point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of
your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects
human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your
local city offi ce, your household waste disposal service or where you purchased the product.
EU COMPLIANCE STATEMENT:
Axial Capra 1.9 (AXI03000)
Horizon Hobby, LLC hereby declares that this product is in compliance with the essential requirements and other relevant provisions of the RED
and EMC Directives.
A copy of the EU Declaration of Conformity is available online at: http://www.horizonhobby.com/content/support-render-compliance.
FCC INFORMATION
IC INFORMATION
COMPLIANCE INFORMATION FOR THE EUROPEAN UNION
CAN ICES-3 (B)/NMB-3(B)
IC: 6157A-STX3
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
FCC ID: BRWSTX3
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modifi cations not expressly approved by the party responsible for compliance could void the user’s authority to operate
the equipment.
This product contains a radio transmitter with wireless technology which has been tested and found to be compliant with the applicable regulations
governing a radio transmitter in the 2.400GHz to 2.4835GHz frequency range.
SUPPLIER’S DECLARATION OF CONFORMITY
Axial Capra 1.9 (AXI03000)
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CAUTION: changes or modifi cations not expressly approved by the party responsible for compliance could void the user’s authority to operate
the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Horizon Hobby, LLC
2904 Research Rd.,
Champaign, IL 61822
Email: compliance@horizonhobby.com
Web: HorizonHobby.com
50
EXPLODED VIEWS // EXPLOSIONSZEICHNUNGEN // VUES ÉCLATÉES // VISTE ESPLOSE
AXA232017
AXI232017
AXA0286
AX31148
AXA31028
AXA144
AXA31028
AXA0286
AX31148
AXI232017
AXI234003
AXI234006
AXI234004
AXI234004
AXI234008
AXI234009
AXI234008
AXI234006
AXI235016
AXI232004
AXA1221
AXA120
AXI234006
AXI234004
AX31407
AXI234004
AXI235109AXI234006
AXI232003
AXA0109
AXI234004
AXI234004
AXA120
AXI235109
AXI234009
AXA144
AXI234006
AXI234006
AXI232004
AXI234006
SPMS614
AXI234004
AXI234006
AXI234003
AXI234004
AXI234004
AXA118
AXI235109
AXI234006
AXI234004
AXI234005
AXI234006
AXI234004
AXI234006
AXI234004
AXA116
AXI234007
AXI234005
AXA115
AXI234006
AXI234004
AXI235004
AXI232006
AXA1221
AXA1221
AX31406
AXI232002
AX31406
AX31066
AXI235004
AXI232006
AXI237009
AXA1221
AXI232007
AXA1230
AXA1221
AX30165
AXI232008
AXI232006
AX31403
AX31403
AXA1221
AXI232009
AXA1221
AXI232004
AXI232009
AX31403
AX31403
AXI237009
AXI232008
AX30165
AXI232006
AXA1230
AXI232007
FRONT AXLE
VORDERACHSE
ESSIEU AVANT
ASSALE ANTERIORE
REAR AXLE
HINTERACHSE
ESSIEU ARRIÈRE
ASSALE POSTERIORE
AXI234003
AXI234008
AXI234009
AXI235014
AXI232005
AXA1221
AXI237009
AXI232007
AXI232008
AX30165
AXA120
AXI234004
AXI234006
AXI232010
AXA232017
AXA144
AXA31028
AXA0286
AX31148
AXI232017
AXA31028
AXI232017
AXA0286
AX31148
AXA1221
AXI235004
AXI232005
AXI237009
AXA1221
AXI232007
AXA1221
AXI232008
AXA1221
AXI234006
AXI235109
AXI234006
AXI234004
AX30165
AXI234006
AXI232010
AXI232005
AXI234004
AXI234004
AXI235016
AX31407
AXI235016
AXI234008
AXI234009
AXI234004
AX31406
AXI232007
AXI232002
AX31066
AXA120
AXI234006
AXI234006
AXI235109
AXI234004
AX31406
AXI234004
51
AXA1225
AXA31642
AXI232014
AXI237003
AXI232012
AXA1234
AXI232014
AXI232011
AXI232013
AXI232014
AXA1218
AXI232011
AXA144
AXA144
AXA146
AXI232011
AX31250
AXA1218
AXA148
AXA144
AXI232014
AXI232013
AXA1218
AXA1218
AX31312
AXI232012
AXI236175
AXA1218
AXI232013
AXA291
AX30569
AXA0109
AXI232015
AXI232011
AXI232011
AXI232012
TRANSMISSION
GETRIEBE
TRANSMISSION
TRASMISSIONE
CHASSIS
KAROSSERIE
CHÂSSIS
TELAIO
AXI231006
AXI230012 (Clear)
AXA113
AXI230011 (Clear)
AXA114
AXI230011 (Clear)
AXI230011
AXI235330
AXI235109
AXI235109
AXA146
AXA144
AXI235109
AXI231005
AXI232011
AXA116
AXI232016
AX31066
AXI235169
AX31066AXA116
AXI232016
SPMSSX107
AXI232016
52
CHASSIS
KAROSSERIE
CHÂSSIS
TELAIO
AXI235097 AXI230012 (Clear)
AXA116
AXA116
AXA116
AXA118
AXA120
AXA118
AXI235097
AXI230012 (Clear)
AXI235269
AXI231006
AXI231006
AXA118
AXI231006
AXA114
AXA116
AXI231006
AXI235097
AXI231006
AXI235097
AXI231006
AXI235098
AXA114
AXI231006
AXI235098
AXA118
AXI231006
AXA118
AXI235097
AXI231006
AXA118
DYNS2213
SPMSRX300
AXA116
AXA118
AXI231006
AXA115
AXA118
AXI230010
AXA231006
AXI235102
AXA120
AXA116
AXA116
AXA116
AXA118
AXI230012 (Clear)
53
SHOCK ABSORBERS
STOSSDÄMPFER
AMORTISSEURS
AMMORTIZZATORI
WHEELS AND TIRES
REIFEN UND RÄDER
ROUES ET PNEUS
RUOTE E PNEUMATICI
AXA1059
AXI231006
AXI236172
AXI232018
AXA114
AXI43004
AX31250
AXI43004
AX31565
AXI235099
AXI233002
AXI233006
AXI233002
AXI233003
AXI233001
AXA1392
AXI233002
AXI233003
AXI233000
AXI235094
AXI233002
54
PARTS LISTS // TEILELISTEN // LISTE DES PIÈCES // ELENCO COMPONENTI
Part # Description Beschreibung Description Descrizione
AXI230010 Head Light Lens
Scheinwerferlinse Lentilles de phares Lenti per faro
AXI230011 Interior Set
Interieurset Ensemble d’intérieur Set interni
AXI230012 Body Panel Set (Clear)
Karosserieteilesatz, farblos
Ensemble de panneaux de carrosserie,
transparent
Set pannelli carrozzeria, trasparente
AXI231005 Skid Plate
Motorschutz Plaque de protection Piastra di protezione
AXI231006 UTB Cage Set Complete
Überrollkäfi gset, komplett Ensemble de cages complet Set scocca completo
AXI232002 6-Bolt Differental Locker
6-Schrauben-Differenzial-Sicherung Blocage différentiel à 6 boulons Blocco differenziale 6 bulloni
AXI232003 6 Bolt Heavy Duty Gear Set
6-Schrauben-Schwerlast-Zahnradsatz
Ensemble d’engrenages haute résistance à
6 boulons
Set ingranaggio impieghi gravosi 6 bulloni
AXI232004 F9 Portal Axl housing FR
Currie F9-Portalachsgehäuse, vorne Carter d’essieu du portique Currie F9, avant
Currie F9 Portal, alloggiamento assale,
anteriore
AXI232005 F9 Portal Axl housing RR
Currie F9-Portalachsgehäuse, hinten Carter d’essieu du portique Currie F9, arrière
Currie F9 Portal, alloggiamento assale,
posteriore
AXI232006 F9 Portal Str knucl & Cap
Currie F9 Portal-Achsschenkel und -abdeckung
Rotule de direction et coiffe du portique Currie
F9, arrière
Currie F9 Portal, fuso a snodo e tappo
AXI232007 32P Portal Gr Set 23T/12T 2pc
32P Portalachssatz 23T/12T (2) Ensemble engrenage portique 32P 23T/12T (2) Set ingranaggi 32P Portal 23T/12T (2)
AXI232008 Portal Stub Axle (2)
Portalachsschenkel (2) Demi-essieu du portique (2) Fusello Portal (2)
AXI232009 F9 Universal Axle Set (2pc)
Currie F9-Universalachsset (2) Ensemble d’essieux universels Currie F9 (2) Currie F9, set assale universale (2)
AXI232010 F9 Straight Axle Shaft 2pc
Currie F9, Gerade Achswelle (2) Ensemble d’essieux droits Currie F9 (2) Currie F9, set assale dritto (2)
AXI232011 Dig Transmission Case Set
Grabgetriebe-Abdeckungssatz Ensemble boîtier de transmission dig Set scatola cambio dig
AXI232012 Dig Trans Metal Gear Set
Grabgetriebe-Metallgetriebesatz
Ensemble d’engrenages métalliques de
transmission dig
Set ingranaggi trasmissione dig in metallo
AXI232013 Dig Transmission Shaft Set
Grabgetriebewellensatz Ensemble d’arbres de transmission dig Set albero trasmissione dig
AXI232014 Dig Trans Dig Cmpnts
Grabgetriebe, „Grab“-komponenten Composants « dig » transmission dig Componenti trasmissione dig
AXI232015 Dig Trans Slipper Pads/Plts
Grabgetriebe-Gleitschuhe/-platten
Sabots de pistons/plaques de sabot de
transmission dig
Piastre/pattini di scorrimento trasmissione dig
AXI232016 Dig Trans Mnts&Srvo Svr Set
Grabgetriebe-Halterungen und Servo-
Saversatz
Ensemble supports et économiseur de servo
de transmission dig
Set salvaservo e supporti trasmissione dig
AXI232017 Wild Boar Driveshaft Set
Wild Boar-Antriebswellensatz Ensemble d’arbres de transmission Wild Boar Set albero di trasmissione Wild Boar
AXI232018 12mm Hex Pin and Spacer (4)
12-mm-Sechskantstift und Abstandhalter (4) Broche hexagonale 12mm et entretoise (4) Distanziale e perno esagonale 12mm (4)
AXI233000 Thrd AL Shk Bdy 11x41.5mm HA 2pc
Gewinde-Aluminium-Stoßdämpfergehäuse
11x41,5mm HA (2)
Carrosserie d’amortisseurs en aluminium fi leté
11x41,5mm HA (2)
Scocca ammortizzatore fi lettata in alluminio
11x41,5mm HA (2)
AXI233001 Shock Shaft M3x53.4 (2pcs)
Kolbenstange M3 x 53,4 mm (2) Bras d’amortisseur M3x53,4mm (2) Albero ammortizzatore M3x53,4mm (2)
AXI233002 Shock Prts Molded
Stoßdämpferteile, gegossen Pièces de l’amortisseur moulées Parti ammortizzatore stampate
AXI233003 Shock O-Ring Set
O-Ring-Satz für den Stoßdämpfer Ensemble de joints toriques d’amortisseur Set O-Ring ammortizzatore
AXI233004 Spring 13x70mm .72lbs/in Prpl(2)
Feder 13x70mm 0,72 lbs/in (326 g/Zoll), violett (2) Ressort 13x70mm 0,72lbs/po, violet (2)
Molla 13x70mm 0,72lbs/in (326 g/pollice), viola (2)
AXI233006 Spring 13x70mm 1.72lbs/in Red(2)
Feder 13x70mm 1,72 lbs/in (780 g/Zoll), rot (2) Ressort 13x70mm 1,72lbs/po, rouge (2)
Molla 13x70mm 1,72lbs/in (780 g/pollice), rosso (2)
AXI233008 Spring 13x70mm 2.4lbs/in Grn(2)
Feder 13x70mm 2,4 lbs/in (1,08 kg/Zoll), grün (2) Ressort 13x70mm 2,4lbs/po, vert (2)
Molla 13x70mm 2,4lbs/in (1,08 kg/pollice), verde (2)
AXI234003 Pvt Ball,Stainless12.75mm(4)
Kugelzapfen, Edelstahl 12,75 mm (4) Rotule, acier inoxydable 12,75mm (4) Pivot ball, inossidabile, 12,75mm (4)
AXI234004 Susp Pvt Ball, Stainless 7.5mm
Kugelzapfen für Federung, Edelstahl 7,5 mm Rotule de suspension, acier inoxydable 7,5mm Pivot ball sospensioni, indossabile, 7,5mm
AXI234005 Steering Lnks Stainless Stl
Spurstangen, Edelstahl Tringleries de direction, acier inoxydable Tiranti sterzo, inossidabili
AXI234006 HD Rod Ends M4 20pcs
Schwerlast-Stangenköpfe M4 (20) Embouts de bielle haute résistance M4 (20) Teste a snodo per impiego gravoso M4 (20)
AXI234007 SS M6x 111mm Link (2pcs)
Edelstahlglied M6 x 111 mm (2) Liaison en acier inoxydable M6x111mm (2) Braccetti in acciaio inossidabile M6x111mm (2)
AXI234008 SS M6x 111mm Link (2pcs)
Edelstahlglied M6x111mm (2) Liaison en acier inoxydable M6x111mm (2) Braccetti in acciaio inossidabile M6x111mm (2)
AXI234009 Stainless Steel M6 x 89mm Link
Edelstahlglied M6x89mm (2) Liaison en acier inoxydable M6x89mm (2) Braccetti in acciaio inossidabile M6x89mm (2)
AXI235014 M2.5 x 10mm, Cap Head Screw (10)
Inbusschraube, M2,5x10mm (10) Vis d’assemblage creuse, M2,5x10mm (10) Vite a testa cilindrica M2,5x10mm (10)
AXI235016 M2.5 x 16mm, Cap Head Screw (10)
Inbusschraube, M2,5x16mm (10) Vis d’assemblage creuse, M2,5x16mm (10) Vite a testa cilindrica M2,5x16mm (10)
AXI235094 M2.5 x 3mm, Button Head (10)
Rundkopfschraube, M2,5x3mm (10) Vis à tête bombée, M2,5x3mm (10) Vite a testa tonda M2,5x3mm (10)
AXI235097 M2.5 x 6mm, BHS (10)
Rundkopfschraube, M2,5x6mm (10) Vis à tête bombée, M2,5x6mm (10) Vite a testa tonda M2,5x6mm (10)
AXI235098 M2.5 x 8mm Button Head Screw(10)
Rundkopfschraube, M2,5x8mm (10) Vis à tête bombée, M2,5x8mm (10) Vite a testa tonda M2,5x8mm (10)
AXI235099 M2.5 x 10mm, Button Head (10)
Rundkopfschraube, M2,5x10mm (10) Vis à tête bombée, M2,5x10mm (10) Vite a testa tonda M2,5x10mm (10)
AXI235102 M2.5 x 18mm, BHS (10)
Rundkopfschraube, M2,5x18mm (10) Vis à tête bombée, M2,5x18mm (10) Vite a testa tonda M2,5x18mm (10)
AXI235109 M3 x 14mm, Button Head Screw(10)
Rundkopfschraube, M3x14mm (10) Vis à tête bombée, M3x14mm (10) Vite a testa tonda M3x14mm (10)
AXI235169 M2.5 x 12mm, Flat Head Screw(10)
Flachkopfschraube, M2,5x12mm (10) Vis à tête plate, M2,5x12mm (10) Vite a testa piana M2,5x12mm (10)
AXI235330 M3x30mm,Cup Point Set Screw (10)
Stellschraube mit Ringschneide M3x30mm (10) Vis de fi xation à bout cuvette M3x30mm (10) Vite di fermo senza testa M3x30mm (10)
AXI236171 M2.5 x 10mm Pin (6)
Stift M2,5x10mm (6) Axe M2.5x10 mm (6) Perno M2,5x10mm (6)
AXI236172 Screw Shaft M3x2.0x12mm
Schraubenschaft M3x2x12mm Tige de vis M3x2x12 mm Albero fi lettato M3x2x12mm
AXI43004 3pc Raceline Mnstr bdlk whl (2)
3x Raceline Monster Beadlock-Rad (2) 3 pièces de verrou de talon Raceline Monster (2) Cerchio Beadlock Raceline Monster in 3 pezzi (2)
AXIC0012 AXA120 Hex Socket Btn Hd M3x25mm
Sechskant-Rundkopfschraube M3x25mm Douille à six pans à tête bombée M3x25mm
Vite a testa tonda con esagono incassato M3x25mm
55
Part # Description Beschreibung Description Descrizione
AXIC0013 AXA013 Cap Hd M2x6mm Blk Oxide
Inbusschraube, M2x6mm, Schwarzoxid Vis d’assemblage creuse M2x6mm brunie Vite a testa cilindrica M2x6mm ossido nero
AXIC0115 AXA115 Hex Skt Butn Head M3x10mm
Sechskant-Rundkopfschraube, M3x10mm Douille à six pans à tête bombée M3x10mm
Vite a testa tonda con esagono incassato
M3x10mm
AXIC0118 AXA144 Hex Flt Hd M3x8mm Blk10mm
Sechskant-Flachkopfschraube, M3x8mm, schwarz (10) Douille à six pans à tête plate M3x8mm noire (10) Vite a testa piana esagonale M3x8mm nero (10)
AXIC0146 AXA146 Hex Skt Flat Hd M3x12mm
Sechskant-Flachkopfschraube, M3x12mm Douille à six pans à tête plate M3x12mm
Vite a testa piana con esagono incassato M3x12mm
AXIC0218 AXA1218 Bearing 5x10x4mm
Lager 5x10x4mm Roulement 5x10x4mm Cuscinetto 5x10x4mm
AXIC0221 AXA1221 Bearing 5x11x4mm
Lager 5x11x4mm Roulement 5x11x4mm Cuscinetto 5x11x4mm
AXIC0286 AXA0286 Screw Shaft M4x2.5x12mm
Schraubenschaft M4x2,5x12 mm Tige de vis M4x2,5x12mm Albero fi lettato M4x2.5x12mm
AXIC0291 AXA291 Set Scr M4x4mm Blk Ox(6)
Stellschraube, M4x4mm, Schwarzoxid (6) Vis de fi xation M4x4mm brunie (6) Vite di fermo M4x4 mm ossido nero (6)
AXIC0795 AX31586 Wb8-hd Std Driveshafts
WB8-HD Standard-Antriebswelle Arbre de transmission standard WB8-HD Albero di trasmissione standard WB8-HD
AXIC1009 AXA0109 Hex Skt Oversize M3x10mm
Sechskant-Übergröße M3x10mm Douille à 6 pans surdimensionnée M3x10mm Viti oversize con esagono incassato M3x10mm
AXIC1148 AX31148 Wb8-hd Drvshft Coupler
WB8-HD-Antriebswellenkupplung
Ensemble de couplage d’arbre de transmission
WB8-HD
Accoppiamento albero trasmissione WB8-HD
AXIC1180
AXA118 Hex Socket BtnHd
M3x18mm(10)
Sechskant-Rundkopfschraube M3x18mm (10) Douille à six pans à tête bombée M3x18mm (10)
Viti a testa tonda con esagono incassato
M3x18mm (10)
AXIC1243 AXA1243 Bearing 15x21x4mm (2)
Lager 15x21x4mm (2) Roulement à billes 15x21x4mm (2) Cuscinetto 15x21x4mm (2)
AXIC3066 AX31066 Cap Hd M2x8mm Blk (10)
Inbusschraube M2x8mm, schwarz (10) Vis d’assemblage creuse M2x8mm noire (10) Vite a testa cilindrica M2x8mm nero (10)
AXIC3150 AX31250 Ser Nyl Nut Blk 4mm(10)
Nylon-Feststellfl anschmutter, 4mm (10) Contre-écrou en nylon strié 4mm (10) Dato fl angiato Nylock nero 4mm (10)
AXIC3165 AX30165 Pin 2.5x12mm (6)
Stift 2,5x12mm (6) Axe M2,5x12mm (6) Perno 2,5x12mm (6)
AXIC4406 AX31406 Bearing 7x14x3.5mm (2)
Lager 7x14x3,5mm (2) Roulement 7x14x3,5mm (2) Cuscinetto 7x14x3,5mm (2)
AXIC4407 AX31407 Bearing 5x14x5mm (2)
Lager 5x14x5mm (2) Roulement 5x14x5 mm (2) Cuscinetto 5x14x5mm (2)
AX31565
1.9" Nitto Trail Grappler Monster
Truck R35 Compound Tire (2)
1,9Zoll Nitto Trail Grappler Monster-Truck
R35 Compound Reifen (2)
Pneu 1.9" Nitto Trail Grappler Monster
Truck R35 Compound (2)
Pneumatico compound 1.9" Nitto Trail
Grappler Monster Truck R35 (2)
DYNS2213 WPAE-5L Brshd ESC LED Port w/IC3
WPAE-5L gebürsteter Geschwindigkeitsregler
LED-Anschluss mit IC3
Port DEL de variateur ESC à balais WPAE-
5L avec IC3
ESC con spazzole WPAE-5L porta LED con
IC3
SPMS614 S614 Metal Gear Servo 23T WP S614 Metallgetriebeservo 23T WP
Servo à engrenages métalliques S614, 23
dents, étanche
Servo con ingranaggi in metallo S614 23T
WP
SPMSRX300 SRX300 3CH Receiver SRX300 3CH Empfänger Récepteur 3 canaux SRX300 Ricevitore SRX300 3 canali
SPMSSX107 SX107 Micro Metal Gear Servo SX107 Mikro-Metallgetriebeservo Micro servo à engrenages métalliques SX107 Micro servo con ingranaggi in metallo SX107
SPMSTX300 Stx 3Ch 2.4 Ghz Fhss Radio Sys Stx 2,4Ghz Fhss-Funksys Mit 3 Kan Système Radio Stx 3Canaux 2,4Ghz Fhss Sistema Radio Fhss Stx 3 Ch 2,4 Ghz
Part # Description Beschreibung Description Descrizione
AX31312 35T Electric Motor 35T Elektromotor Moteur électrique 35T Motore elettrico 35T
SPMSTX300 STX3 3CH Radio STX3 3CH Sender Radio 3 canaux STX3 Radiocomando STX3 3 canali
SPMSRX300 SRX300 3CH Receiver SRX300 3CH Empfänger Récepteur 3 canaux SRX300 Ricevitore SRX300 3 canali
SPMS614 S614 Metal Gear Servo 23T WP S614 Metallgetriebeservo 23T WP
Servo à engrenages métalliques S614, 23
dents, étanche
Servo con ingranaggi in metallo S614 23T
WP
SPMSSX107 SX107 Micro Metal Gear Servo SX107 Mikro-Metallgetriebeservo Micro servo à engrenages métalliques SX107 Micro servo con ingranaggi in metallo SX107
DYNS2213
AE-5L ESC w/LED Ports and Lights
(2 White, 4 White, 2 Red)
AE-5L Geschwindigkeitsregler mit LED-
Anschlüssen und -Leuchten
(2 x weiß, 4 x weiß, 2 x rot)
Variateur ESC AE-5L avec ports et témoins
DEL (2 blancs, 4 blancs, 2 rouges)
ESC AE-5L con porte e luci LED
(2 bianche, 4 bianche, 2 rosse)
ELECTRONICS // ELECTRONIK // COMPOSANTS ÉLECTRONIQUES // ELETTRONICA
©2019 Horizon Hobby, LLC.
Axial, the Axial logo, Capra, DSM, STX3, IC3 and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC.
The Spektrum trademark is used with permission of Bachmann Industries, Inc. Nitto
®
and Trail Grappler
®
are registered trademarks of Nitto Tire U.S.A., Inc.
The CRC name and logo are trademarks or registered trademarks of Casey Currie Motorsports. The Raceline Wheels name and logo are trademarks or registered
trademarks of Allied Wheel Components, Inc. All other trademarks, service marks and logos are property of their respective owners.
Completed 11/19 AXI03000 59181.1
facebook.com/axialinc | instagram.com/axialracing | twitter.com/axialrc
youtube.com/axialvideos | fl ickr.com/axialrc
OFFICIALLY LICENSED BY:
AXI03000
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Axial AXI03000B Le manuel du propriétaire

Catégorie
Jouets télécommandés
Taper
Le manuel du propriétaire
Ce manuel convient également à

dans d''autres langues