Axial AXI03030T1 Manuel utilisateur

Marque: Axial

Modèle: AXI03030T1

Catégorie: Jouets télécommandés

Taper: Manuel utilisateur

AXI03030T1/T2

INSTRUCTION MANUAL

BEDIENUNGSANLEITUNG

MANUEL D’UTILISATION

MANUALE DI ISTRUZIONI

Scan the QR code and select the Manuals and Support quick links from the

product page for the most up-to-date manual information.

Scannen Sie den QR-Code und wählen Sie auf der Produktseite die Quicklinks

Handbücher und Unterstützung, um die aktuellsten Informationen zu Handbücher.

Scannez le code QR et sélectionnez les liens rapides Manuals and Support sur la

page du produit pour obtenir les informations les plus récentes sur le manuel.

Scannerizzare il codice QR e selezionare i Link veloci Manuali e Supporto dalla

pagina del prodotto per le informazioni manuali più aggiornate.

SCX10™ III BASE CAMP 1982

CHEVY® K10®

Age Recommendation: Not for children under 14 years. This is not a toy.

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate

the product correctly can result in damage to the product, personal property and cause serious injury.

This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to

operate this Product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for

use by children without direct adult supervision. Do not use with incompatible components or alter this product in any way outside of the instructions

provided by Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the

instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.

NOTICE

All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date

product literature, visit horizonhobby.com or towerhobbies.com and click on the support or resources tab for this product.

MEANING OF SPECIAL LANGUAGE

The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:

WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR

create a high probability of superﬁcial injury.

CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.

NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no possibility of injury.

As the user of this product, you are solely responsible for operating in a manner that does not endanger yourself and others or result in damage

to the product or property of others.

This model is controlled by a radio signal subject to interference from many sources outside your control. This interference can cause momentary

loss of control, so it is advisable to always keep a safe distance in all directions around your model as this margin will help avoid collisions or injury.

• Never operate your model with low transmitter batteries.

• Always operate your model in open spaces away from full-size

vehicles, trafﬁc and people.

• Never operate the model in the street or in populated areas for any

reason.

• Carefully follow the directions and warnings for this and any optional

support equipment (chargers, rechargeable battery packs, etc.) you use.

• Keep all chemicals, small parts and anything electrical out of the

reach of children.

• Never lick or place any portion of the model in your mouth as it could

cause serious injury or even death.

• Exercise caution when using tools and sharp instruments.

• Take care during maintenance as some parts may have sharp edges.

• Immediately after using your model, do NOT touch equipment

such as the motor, electronic speed control and battery, because

they generate high temperatures. You may burn yourself seriously

touching them.

• Do not put ﬁngers or any objects inside rotating and moving parts, as

this may cause damage or serious injury.

• Always turn on your transmitter before you turn on the receiver in the

car. Always turn off the receiver before turning your transmitter off.

• Keep the wheels of the model off the ground when checking the

operation of the radio equipment.

SAFETY PRECAUTIONS AND WARNINGS

WARNING AGAINST COUNTERFEIT PRODUCTS: Always purchase from a Horizon Hobby, LLC authorized dealer to ensure

authentic high-quality Spektrum product. Horizon Hobby, LLC disclaims all support and warranty with regards, but not limited to,

compatibility and performance of counterfeit products or products claiming compatibility with DSM® or Spektrum technology.

Your new Horizon Hobby vehicle has been designed and built with

a combination of waterproof and water-resistant components to

allow you to operate the product in many “wet conditions,” including

puddles, creeks, wet grass, snow and even rain.

While the entire vehicle is highly water-resistant, it is not completely

waterproof and your vehicle should NOT be treated like a submarine.

The various electronic components used in the vehicle, such as the

Electronic Speed Control (ESC), servo(s) and receiver are waterproof,

however, most of the mechanical components are water-resistant and

should not be submerged.

Metal parts, including the bearings, hinge pins, screws and nuts, as

well as the contacts in the electrical cables, will be susceptible to

corrosion if additional maintenance is not performed after running in

wet conditions. To maximize the long-term performance of your vehicle

and to keep the warranty intact, the procedures described in the “Wet

Conditions Maintenance” section below must be performed regularly

if you choose to run in wet conditions. If you are not willing to perform

the additional care and maintenance required, then you should not

operate the vehicle in those conditions.

CAUTION: Failure to exercise caution while using this

product and complying with the following precautions could

result in product malfunction and/or void the warranty.

GENERAL PRECAUTIONS

• Read through the wet conditions maintenance procedures and make

sure that you have all the tools you will need to properly maintain your

vehicle.

• Not all batteries can be used in wet conditions. Consult the battery

manufacturer before use. Caution should be taken when using Li-Po

batteries in wet conditions.

• Most transmitters are not water-resistant. Consult your transmitter’s

manual or the manufacturer before operation.

• Never operate your transmitter or vehicle where lightning may be present.

• Do not operate your vehicle where it could come in contact with salt

water (ocean water or water on salt-covered roads), contaminated

or polluted water. Salt water is very conductive and highly corrosive,

so use caution.

• Even minimal water contact can reduce the life of your motor if it

has not been certiﬁed as water-resistant or waterproof. If the motor

becomes excessively wet, apply very light throttle until the water is

mostly removed from the motor. Running a wet motor at high speeds

may rapidly damage the motor.

• Driving in wet conditions can reduce the life of the motor. The

additional resistance of operating in water causes excess strain. Alter

the gear ratio by using a smaller pinion or larger spur gear. This will

increase torque (and motor life) when running in mud, deeper puddles,

or any wet conditions that will increase the load on the motor for an

extended period of time.

WET CONDITIONS MAINTENANCE

• Drain any water that has collected in the tires by spinning them at high

speed. With the body removed, place the vehicle upside down and pull

full throttle for a few short bursts until the water has been removed.

CAUTION: Always keep hands, ﬁngers, tools and any loose

or hanging objects away from rotating parts when performing

the above drying technique.

• Remove the battery pack(s) and dry the contacts. If you have an air

compressor or a can of compressed air, blow out any water that may

be inside the recessed connector housing.

• Remove the tires/wheels from the vehicle and gently rinse the mud

and dirt off with a garden hose. Avoid rinsing the bearings and

transmission.

NOTICE: Never use a pressure washer to clean your vehicle.

• Use an air compressor or a can of compressed air to dry the vehicle

and help remove any water that may have gotten into small crevices or

corners.

• Spray the bearings, drive train, fasteners and other metal parts with

a water-displacing light oil. Do not spray the motor.

• Let the vehicle air dry before you store it. Water (and oil) may

continue to drip for a few hours.

• Increase the frequency of disassembly, inspection and lubrication of

the following:

-Front and rear axle hub assembly bearings.

-All transmission cases, gears and differentials.

-Motor—clean with an aerosol motor cleaner and re-oil the

bushings with lightweight motor oil.

WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS

TABLE OF CONTENTS

Water-resistant Vehicle with Waterproof Electronics ..............................3

box Contents .....................................................................................................4

Required Equipment ........................................................................................ 4

recommended tools .........................................................................................4

Getting started checklist.................................................................................5

Vehicle parts .....................................................................................................5

Charge the vehicle battery .............................................................................6

Install the transmitter batteries .....................................................................6

Transmitter functions ......................................................................................6

SPMSR315 dual protocol Receiver ...............................................................7

Adjusting the Vehicle battery tray .................................................................7

Install the vehicle battery ...............................................................................8

Binding ...............................................................................................................8

Range-checking the radio system ................................................................ 9

vehicle maintenance .......................................................................................9

Firma 40A Brushed ESC ................................................................................ 10

Gear Ratios......................................................................................................10

Troubleshooting ..............................................................................................11

Limited Warranty ............................................................................................12

Warranty and Service Contact Information ..............................................12

FCC Information ..............................................................................................13

IC Information .................................................................................................13

Compliance Information for the European Union .....................................13

Parts Lists ........................................................................................................56

Recommended Parts .....................................................................................58

Optional Parts .................................................................................................58

BOX CONTENTS

• Battery charger compatible with

the chosen vehicle battery type

• Hex Drivers

(1.5, 2.0, 2.5mm) • Hobby

Knife • Side Cutter • Curved

Scissors • Long-nose Plier

RECOMMENDED TOOLS

• Parts Bag • Cross Wrench

REQUIRED EQUIPMENT

• 2-3S Standard or “Shorty” LiPo Battery

• 5-9 Cell NiMH/NiCd battery

(IC3® Connector Required)

• Spektrum™ SLT3 3 Channel 2.4GHz Transmitter (SPMRSLT300)

• Axial® SCX10™ III 1982 CHEVY® K10® RTR

- 35T Electric Motor (DYNS1216)

- 40A Smart Brushed ESC (SPMXSE1040)

- Spektrum DSMR® 3 Channel Receiver (SPMSR315)

- Water Proof Metal Gear Surface Servo, 23T (SPMS614)

- (4) AA Alkaline batteries

• (4) AA Alkaline

batteries

Steering Servo

Transmission

Driveshaft

Upper 4-link Bar

Differential

(inside axle housing)

Front Body Mount

Rear Body Mount

Lower 4-link Bar

Shock Absorber

VEHICLE PARTS

GETTING STARTED CHECKLIST

Read the manual

Familiarize yourself with the vehicle and its components

Check all screws, especially the driveshaft setscrews, for

tightness from the factory

Charge the vehicle battery

Install 4 AA batteries in the transmitter

Install the vehicle battery in the vehicle

Power on the transmitter and then connect battery to ESC

Check for proper function of the throttle and steering

Range check the radio system

Drive the vehicle, challenge yourself, and have FUN!

Perform any necessary vehicle maintenance

Steering Knuckle

“Shorty” Battery Tray

Standard Battery Tray

Receiver

ESC

INSTALL THE TRANSMITTER BATTERIES

TRANSMITTER FUNCTIONS

This transmitter requires 4 AA batteries.

1. Remove the battery cover from the transmitter.

2. Install the batteries as shown.

3. Install the battery cover.

CAUTION: NEVER remove the transmitter batteries while the

model is powered on. Loss of model control, damage, or injury

may occur.

CAUTION: If using rechargeable batteries, charge only

rechargeable batteries. Charging non-rechargeable batteries

may cause the batteries to burst, resulting in injury to persons and/or

damage to property.

CAUTION: Risk of explosion if battery is replaced by an incorrect

type. Dispose of used batteries according to national regulations.

Follow the manufacturer’s directions for your charger to properly

charge the vehicle battery.

CAUTION: Only use chargers designed to charge the chosen

battery type. Using an incorrect charger or incorrect charger

settings could cause the battery to catch ﬁre or explode.

CHARGE THE VEHICLE BATTERY

A. Throttle Trim

Adjusts the throttle neutral point

B. Steering Trim

Adjusts the steering center point. Normally, the steering trim is

adjusted until the vehicle tracks straight.

C. LED

• Solid red lights: Indicates the power is ON and adequate battery

power

• Flashing red lights: Indicates the battery voltage is critically low.

Replace batteries

D. Steering Wheel

E. Throttle/Brake

F. Steering Rate

On-The-Fly knob for travel adjustment on the steering

G. Channel 3

3 position momentary switch, middle position is neutral

For programming press up for A button, press down for B button

H. Throttle Limit

Limits throttle output to 50/75/100%

Select 50% or 75% for less experienced drivers or when you are

driving the vehicle in a small area.

I. Throttle (TH) Servo Reversing

Move the switch to reverse the throttle channel

J. Steering (ST) Servo Reversing

Move the switch to reverse the steering channel

K. Power Button

SPECIFICATIONS

Power Supply: 4 AA Batteries

Operating Frequency: 2.4GHz

Transmit Power: <100mw

Control Protocol: SLT

Control: Proportional Steering and Throttle/Brake with Trim Knobs,

Third Channel with 3 Position Momentary Switch

Auxiliary Functions: 3 Position Throttle Limit Switch, Steering Rate

Knob to Change Steering Travel on-the-ﬂy, Programmable Servo Travel

for Steering and Throttle/Brake

SPMSR315 DUAL PROTOCOL RECEIVER

STR THR

BATT

AUX 1

SPECIFICATIONS

Type

Dual

Protocol 3 Ch Receiver (SLT/DSMR)

Dimensions (L × W × H) 32.5 x 21.5 x 12.4mm

Antenna Length 90mm

Channels 3

Weight 6g

Band 2.4GHz

Voltage Range 3.5–9.6V

Bind Type Button

ADJUSTING THE VEHICLE BATTERY TRAY

The battery trays may be adjusted to ﬁt a wide range of battery sizes.

The rear battery tray is shown in the illustration. The side battery tray

is adjustable in the same manner.

To adjust the battery tray:

1. Loosen the four ﬂathead screws shown in the illustration.

2. Slide the ends of the battery tray in or out to ﬁt the desired battery.

3. Tighten the four ﬂathead screws. Do not over-tighten the screws.

Power

INSTALL THE VEHICLE BATTERY

The following steps show the installation of a standard size battery in the rear battery tray of the vehicle. If you wish to use a “shorty” style

battery, it should be installed in the side battery tray location.

Binding is the process of programming the receiver to recognize the

GUID (Globally Unique Identiﬁer) code of a single speciﬁc transmitter.

Failsafe:

Hold the steering wheel and throttle trigger in the desired

failsafe positions during binding

1. Press and hold the bind button.

2. Power ON the receiver. The orange LED will begin to ﬂash.

3. Set the trims and control positions at the desired failsafe settings.

4. Power ON the SLT3 transmitter.

5. When the transmitter’s orange LED remains lit, it is connected to

SR315 receiver.

You must rebind when:

• Different failsafe positions are desired (e.g., when throttle or steering

reversing has changed).

• Binding the receiver to a different transmitter.

Bind Button

BINDING

2. Remove the four body clips from the body.

3. Lift the body from the chassis.

4. Place the battery in the battery tray. The battery tray length may be

adjusted to ﬁt the battery as described in the previous section.

5. Secure the battery to the tray with the hook and loop strap.

6. Connect the battery to the ESC.

7. Re-install the body and four body clips to the chassis.

NOTICE: Always disconnect the battery from the ESC before

powering off the transmitter. Loss of vehicle control may result.

1. Power on the transmitter.

The radio system should be checked before operating the vehicle to ensure proper operation and adequate range.

1. Turn on the transmitter.

2. Connect the battery in the vehicle.

3. Have a friend hold the vehicle while keeping hands and loose clothing away from moving parts.

4. Walk away until you are at the maximum planned operating distance from the vehicle.

5. Turn the steering wheel side to side and operate the throttle, both forward and reverse, checking for any

erratic behavior.

6. If any erratic behavior is exhibited, DO NOT operate the vehicle. Contact customer service for assistance.

RANGE-CHECKING THE RADIO SYSTEM

Replace any

noticeable bent or

broken parts

Check the wheel nuts

for tightness

If applicable, check

the slipper clutch for

proper operation

Check for wear on

the ball joints in

the steering and

suspension links

(replace if necessary)

Ensure the wheel

beads are still ﬁrmly

bonded around the

entire circumference

of the rim

Check the receiver

antenna for damage

Check driveshaft

set screws and

apply thread

locking compound if

necessary

Keep the chassis free

of dirt and debris

Check the steering

operation for any

binding

Inspect shock

absorbers for smooth

dampened operation

Check for loose

screws on the chassis,

especially the knuckle,

C-hub and axle lockout

screws

Inspect the spur

and pinion gears for

damage

Check for any loose

connections or frayed

wiring

Check the driveline

for smooth, bind free

operation

Replace the

transmitter batteries

when indicated by

the transmitter, as

described in the

Transmitter Functions

section

Just like a full size car or truck, your RC vehicle must undergo periodic maintenance in order to ensure peak performance. Preventative maintenance

will also help avoid needless breakages which could result in costly repairs. Below are some suggestions to properly maintain your vehicle.

VEHICLE MAINTENANCE

GEAR RATIOS

FIRMA 40A BRUSHED ESC

Battery ESC

Red

Black

Motor

To Receiver

Throttle Channel

SETUP

Throttle calibration should not be needed out of the box. However,

in order to make the throttle range of different transmitters, the

calibration of the ESC is necessary:

• Mount the ESC in an area that is well ventilated and isolated from

vibration and shock.

• Connect the ESC motor wires to the motor red-to-red and black-to-

black.

• Plug the receiver into the throttle channel of the receiver.

• Before plugging the battery into the ESC, make sure your transmitter

is on and the throttle trim is set to zero.

• Connect the battery to the ESC. The vehicle will be powered on

when the battery is connected.

CAUTION: Keep all body parts and loose clothing away from

any moving parts while the battery is connected to the ESC.

CAUTION: Always connect the ESC only to a proper power

source that has the correct voltage and polarity. Incorrect voltages

or reversed polarity will damage the ESC. Damage to the ESC caused by

improper voltage or polarity is not covered under warranty.

• Test forward and reverse control using the transmitter.

TO CALIBRATE THE ESC:

• Power the transmitter on and set the throttle control to neutral.

• Connect the battery to the ESC and wait 3 seconds to let the ESC

initiate a self-test and automatic throttle calibration.

• The ESC is ready to run when a long beep sound is emitted from the motor.

• Always disconnect the battery when the vehicle is not in use.

IMPORTANT: The LiPo cut-off is set to “ON” and the drag brake is

set to 100% from the factory.

Mode

Battery

(BATT)

Forward/Brake/

Reverse (F/B/R) 50% Drag

Brake 100% Drag Brake

(default)

Li-Po

(default) Ni-MH

SPECIFICATIONS

Type Brushed

Constant/Peak 40A/180A

Resistance 0.002 Ohms

Function Forward/Brake/Reverse, Forward/Brake,

Forward/Reverse (Crawler Mode)

Vehicle Type 1/10 on-road and off-road; 1/10 rock crawler

Operation Proportional forward, proportional reverse

with braking delay, Crawler Mode

Battery Type/Input

Voltage 2–3 cell Li-Po/Li-Fe; 5–9 cell Ni-MH/Ni-Cd

Motor Type 2S Li-Po down to 12T; 3S Li-Po down to 18T

BEC Output 6V/3A

Dimensions 46.5mm x 34mm x 28.5mm (1.8 x 1.3 x 1.1 in)

Weight 70g (2.5 oz)

Battery Connector IC3™ connector

SOUND INDICATOR

OPERATION SOUND

Ni-MH/Ni-CD Battery 1 Short Beep

2S Li-Po Battery 2 Short Beeps

3S Li-Po Battery 3 Short Beeps

ESC Ready 1 Long Beep

SPUR/PINION GEAR RATIO CHART - LCX TRANSMISSION

12 13 14 (stock) 15 16 17 18

Portal Axles (stock) 55.1 50.9 47.2 44.1 41.3 38.9 36.7

Standard Axles (optional) 30.5 28.1 26.1 24.4 22.9 21.5 20.3

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE SOLUTION

The system will not connect

Your transmitter and receiver are too

close together Move transmitter 8 to 12 feet away from receiver

You are near metal objects Move to an area with less metal

The receiver is bound to a different

model memory Make sure the correct model memory is active in your

transmitter

Your transmitter was placed into bind

mode and is no longer bound to your

receiver Rebind your transmitter and receiver, and then re-calibrate

The receiver goes into failsafe a short

distance away from the transmitter Check for damage on the receiver

antenna

Make sure your receiver antenna is protected and located

as high as practical

Replace the receiver or contact Horizon Product Support

The receiver stops responding during

operation

Low receiver battery voltage. If the

battery voltage is low, it may drop

below 3.5V momentarily, causing the

receiver to brown-out, then reconnect

Charge the receiver or vehicle battery. Spektrum receivers

require at least 3.5V to operate

Loose or damaged wires or connectors

between battery and receiver Check the wires and connection between the battery and

receiver. Repair or replace wires and/or connectors

Vehicle does not move

Batteries are not installed properly in

the transmitter Ensure the transmitter batteries are properly installed

Weak or no battery in the vehicle Install a freshly charged vehicle battery

Damaged motor Replace the motor

Frayed or broken wiring Replace any damaged wiring

ESC is shut down by heat protection circuit

Allow the ESC to cool down completely

Loss of vehicle control

Improper antenna placement Ensure the transmitter antenna is not blocked and the

receiver antenna is located properly

Weak or no batteries in the transmitter

or vehicle Install a freshly charged vehicle battery and new

transmitter batteries

Neutral or trim position is incorrect Adjust the steering trim

Receiver and/or battery not connected

properly Check all receiver and battery connections

Steering and/or throttle function is

reversed

Servo travel is reversed at the transmitter Set the transmitter servo reversing switch to the correct position

Motor wires are not connected properly Check all motor wires for correct polarity and secure connection

ESC ON - No motor function, audible tone

or LED

Battery/connection issue Recharge/replace battery. Secure all connections

Damaged ESC Repair/replace ESC

Damaged motor Repair/replace

Motor- Stops and LED blinks

Low voltage protection When the ESC LED blinks, recharge/replace battery

Overheat protection When the LED blinks, let motor/ESC cool, change set up or

gearing to avoid overheating

Motor- Accelerates irregularly

Battery issue Repair damaged wiring/replace battery

Incorrect gearing Adjust/replace gearing

Worn or damaged motor Repair/replace motor

Motor- Does not turn continuously in

response to throttle ESC/motor damaged Repair/replace wiring or motor/ESC

Motor- Slows but will not stop Incorrect transmitter/ESC calibration Adjust throttle travel/other throttle settings on the

transmitter/ESC. Repeat the ESC Calibration Procedure

Steering servo- Operates; motor does not

run

Damaged motor Test the motor apart from the vehicle system, repair/replace

motor as needed

Incorrect transmitter/ESC calibration Adjust throttle travel/other throttle settings on the

transmitter/ESC. Repeat the ESC Calibration Procedure

Steering/motor- not functioning

Low battery voltage Recharge/replace

Wrong model memory selected on

transmitter Select correct model settings on your transmitter, refer to

transmitter and/or receiver manual

Receiver not bound to transmitter Bind transmitter to receiver, refer to transmitter and/or

receiver manual

Vehicle- Does not operate at full speed

Battery issue Recharge/replace

Incorrect transmitter/ESC calibration Adjust throttle travel/other throttle settings on the

transmitter/ESC. Repeat the ESC Calibration Procedure

What this Warranty Covers

Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the

product purchased (the “Product”) will be free from defects in materials

and workmanship for a period of 2 years from the date of purchase.

What is Not Covered

This warranty is not transferable and does not cover (i) cosmetic damage,

(ii) damage due to acts of God, accident, misuse, abuse, negligence,

commercial use, or due to improper use, installation, operation or

maintenance, (iii) modiﬁcation of or to any part of the Product, (iv)

attempted service by anyone other than a Horizon Hobby authorized

service center, (v) Product not purchased from an authorized Horizon

dealer, or (vi) Product not compliant with applicable technical regulations

or (vii) use that violates any applicable laws, rules, or regulations.

OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO

OTHER WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS

ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT

LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE

PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED

THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF

THE PURCHASER’S INTENDED USE.

Purchaser’s Remedy

Horizon’s sole obligation and purchaser’s sole and exclusive remedy

shall be that Horizon will, at its option, either (i) service, or (ii) replace,

any Product determined by Horizon to be defective. Horizon reserves

the right to inspect any and all Product(s) involved in a warranty

claim. Service or replacement decisions are at the sole discretion of

Horizon. Proof of purchase is required for all warranty claims. SERVICE

OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE

PURCHASER’S SOLE AND EXCLUSIVE REMEDY.

Limitation of Liability

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT,

INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR

PRODUCTION OR COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF

WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, TORT,

NEGLIGENCE, STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY,

EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH

DAMAGES. Further, in no event shall the liability of Horizon exceed the

individual price of the Product on which liability is asserted. As Horizon

has no control over use, setup, ﬁnal assembly, modiﬁcation or misuse,

no liability shall be assumed nor accepted for any resulting damage

or injury. By the act of use, setup or assembly, the user accepts all

resulting liability. If you as the purchaser or user are not prepared to

accept the liability associated with the use of the Product, purchaser

is advised to return the Product immediately in new and unused

condition to the place of purchase.

Law

These terms are governed by Illinois law (without regard to conﬂict of law

principals). This warranty gives you speciﬁc legal rights, and you may also

have other rights which vary from state to state. Horizon reserves the right

to change or modify this warranty at any time without notice.

WARRANTY SERVICES

Questions, Assistance, and Services

Your local hobby store and/or place of purchase cannot provide

warranty support or service. Once assembly, setup or use of the Product

has been started, you must contact your local distributor or Horizon

directly. This will enable Horizon to better answer your questions and

service you in the event that you may need any assistance. For questions

or assistance, please visit our website at www.horizonhobby.com,

submit a Product Support Inquiry, or call the toll free telephone number

referenced in the Warranty and Service Contact Information section to

speak with a Product Support representative.

Inspection or Services

If this Product needs to be inspected or serviced and is compliant in

the country you live and use the Product in, please use the Horizon

Online Service Request submission process found on our website

or call Horizon to obtain a Return Merchandise Authorization (RMA)

number. Pack the Product securely using a shipping carton. Please

note that original boxes may be included, but are not designed to

withstand the rigors of shipping without additional protection. Ship

via a carrier that provides tracking and insurance for lost or damaged

parcels, as Horizon is not responsible for merchandise until it arrives

and is accepted at our facility. An Online Service Request is available

at http://www.horizonhobby.com/content/service-center_render-

service-center. If you do not have internet access, please contact

Horizon Product Support to obtain a RMA number along with

instructions for submitting your product for service. When calling

Horizon, you will be asked to provide your complete name, street

address, email address and phone number where you can be reached

during business hours. When sending product into Horizon, please

include your RMA number, a list of the included items, and a brief

summary of the problem. A copy of your original sales receipt must be

included for warranty consideration. Be sure your name, address, and

RMA number are clearly written on the outside of the shipping carton.

NOTICE: Do not ship Li-Po batteries to Horizon. If you have any

issue with a Li-Po battery, please contact the appropriate Horizon

Product Support ofﬁce.

Warranty Requirements

For Warranty consideration, you must include your original sales

receipt verifying the proof-of-purchase date. Provided warranty

conditions have been met, your Product will be serviced or replaced

free of charge. Service or replacement decisions are at the sole

discretion of Horizon.

Non-Warranty Service

Should your service not be covered by warranty, service will be

completed and payment will be required without notiﬁcation or

estimate of the expense unless the expense exceeds 50% of the retail

purchase cost. By submitting the item for service you are agreeing

to payment of the service without notiﬁcation. Service estimates

are available upon request. You must include this request with your

item submitted for service. Non-warranty service estimates will be

billed a minimum of 1/2 hour of labor. In addition you will be billed for

return freight. Horizon accepts money orders and cashier’s checks,

as well as Visa, MasterCard, American Express, and Discover cards.

By submitting any item to Horizon for service, you are agreeing to

Horizon’s Terms and Conditions found on our website http://www.

horizonhobby.com/content/service-center_render-service-center.

ATTENTION: Horizon service is limited to Product compliant in

the country of use and ownership. If received, a non-compliant

Product will not be serviced. Further, the sender will be responsible

for arranging return shipment of the un-serviced Product, through

a carrier of the sender’s choice and at the sender’s expense.

Horizon will hold non-compliant Product for a period of 60 days from

notiﬁcation, after which it will be discarded.

10/15

COUNTRY OF PURCHASE HORIZON HOBBY CONTACT INFORMATION ADDRESS

United States of America

Horizon Service Center

(Repairs and Repair Requests) servicecenter.horizonhobby.com/RequestForm/

2904 Research Rd

Champaign, IL 61822

Horizon Product Support

(Product Technical Assistance)

productsupport@horizonhobby.com

877-504-0233

Sales websales@horizonhobby.com

800-338-4639

European Union Horizon Technischer Service service@horizonhobby.eu Hanskampring 9

D 22885 Barsbüttel, Germany

Sales: Horizon Hobby GmbH +49 (0) 4121 2655 100

LIMITED WARRANTY

WARRANTY AND SERVICE CONTACT INFORMATION

EU COMPLIANCE STATEMENT:

Axial SCX10 III Base Camp 1982 Chevy K10 RTR

(AXI03030)

Hereby, Horizon Hobby, LLC declares that the device is in compliance

with the following: EU Radio Equipment Directive 2014/53/EU; RoHS 2

Directive 2011/65/EU; RoHS 3 Directive - Amending 2011/65/EU Annex

II 2015/863.

The full text of the EU declaration of conformity is available at the

following internet address: https://www.horizonhobby.com/content/

support-render-compliance.

Wireless Frequency Range and Wireless Output Power

Transmitter

2403.0 - 2480.0 MHz

16.3 dBm

Receiver

2404-2476 MHz

-1.33dBm

EU Manufacturer of Record:

Horizon Hobby, LLC

2904 Research Road

Champaign, IL 61822 USA

EU Importer of Record:

Horizon Hobby, GmbH

Hanskampring 9

22885 Barsbüttel Germany

WEEE NOTICE:

This appliance is labeled in accordance with European

Directive 2012/19/EU concerning waste of electrical and

electronic equipment (WEEE). This label indicates that this

product should not be disposed of with household waste. It

should be deposited at an appropriate facility to enable

recovery and recycling.

FCC INFORMATION

IC INFORMATION

COMPLIANCE INFORMATION FOR THE EUROPEAN UNION

CAN ICES-3 (B)/NMB-3(B)

IC: 6157A-SPMSLT300

IC: 6157A-SRIRVINGV1

This device contains license-exempt transmitter(s)/receivers(s)

that comply with Innovation, Science, and Economic Development

Canada’s license-exempt RSS(s). Operation is subject to the following

2 conditions:

1. This device may not cause interference.

2. This device must accept any interference, including interference

that may cause undesired operation of the device.

FCC ID: BRWSPMSLT300

FCC ID: BRWSRIRVINGV1

SUPPLIER’S DECLARATION OF CONFORMITY

Axial SCX10 III Base Camp 1982 Chevy K10 RTR (AXI03030)

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause

undesired operation.

CAUTION: changes or modiﬁcations not expressly approved

by the party responsible for compliance could void the user’s

authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Horizon Hobby, LLC

2904 Research Rd.,

Champaign, IL 61822

Email: compliance@horizonhobby.com

Web: HorizonHobby.com

EXPLODED VIEWS // EXPLOSIONSZEICHNUNGEN // VUES ÉCLATÉES // VISTE ESPLOSE

AXI03030

SCX10™ III BASE CAMP 1982 CHEVY® K10®

AXI234006

AXI234004

AXI232017

AXI234035

AXI234006

AXI234003

AXI235109

AXI234004

AXI234010

AXIC0012

AXI234035

AXI234004

AXIC0230

AXIC4403

AXIC4406

AXIC3066

AXI232003

AXI234004

AXIC0221

AXI232017

AXIC0286

AXIC1148

AXI235016

AXI234003

AXIC0118

AXI235014

AXIC1028

AXIC0221

AXI232006

AXI232027

AXI232008

AXIC0221

AXI232008

AXI235110

AXI237009

AXIC0012

AXI234004

AXI234006

AXI232018

AXIC3165

AXI235014

AXIC0221

AXI234035

AXI235109

AXIC1148

AXIC0012

AXIC1028

AXI232017

AXI234004

AXI232008

AXIC3165

AXIC4403

AXI234004

AXIC0221

AXI232027

AXIC0221

AXI237009

AXI232018

AXI237008

AXI232022

AX31047

AXIC4406

AXI232002

AXI232026

AXI232006

AXIC0230

AXIC0221

AXI234006

AXI234035

FRONT AXLE

VORDERACHSE

ESSIEU AVANT

ASSALE ANTERIORE

EXPLODED VIEWS // EXPLOSIONSZEICHNUNGEN // VUES ÉCLATÉES // VISTE ESPLOSE

AXI03030

SCX10™ III BASE CAMP 1982 CHEVY® K10®

AXI235014

AXI232018

AXI232023

AXIC0221

AXIC0012

AXI237009

AXI234006

AXI232028

AXI232008

AXIC3165

AXIC0221

AXI234006

AXI234003 AXI232018

AXI232023

AXIC3165

AXI232008

AXI235014

AXIC4407

AXI232003

AXI232028

AXI232007

AXI232002

AXI232026

AXIC3066

AXIC4406

AXI237009

AXI234004

AXI232017

AXI235016

AXIC0221

AXIC0286

AXIC1028

AXIC0118

AXIC1028

AXIC0286

AXIC1148

AXI232017

AXI234035

AXIC1148

AXI234035

AXI234004

AXI232007

AXI234004

AXI234003

AXI234006

AXIC0012

AXI232023

REAR AXLE

HINTERACHSE

ESSIEU ARRIÈRE

ASSALE POSTERIORE

EXPLODED VIEWS // EXPLOSIONSZEICHNUNGEN // VUES ÉCLATÉES // VISTE ESPLOSE

AXI03030

SCX10™ III BASE CAMP 1982 CHEVY® K10®

AXA146

AXI232064

AXIC0218

AXIC0225

AXIC1213

AXI232069

AXA0013

AXI232068

AXIC0218

AXI236136

AXIC1213

AXI232069

AXI232070

AXI232017

AXIC0118

AXA144

AXI232017

AXIC1148

AXIC1028

AX31028

AXIC0286

AXI232017

DYNS1216

AXIC0291

AX30725

AXI232064

AXIC0118

AXI232067

AXIC1009

AXI232066

AXIC1185

AXI232065

AXI232067

AXIC3150

AXI232064

AXI234004

AXI231047

AXIC1180

AXA114

AXIC0114

AXA115

AXIC0115

AXIC1185

AXIC1180

AXIC0116

TRANSMISSION

GETRIEBE

TRANSMISSION

TRASMISSIONE

EXPLODED VIEWS // EXPLOSIONSZEICHNUNGEN // VUES ÉCLATÉES // VISTE ESPLOSE

AXI03030

SCX10™ III BASE CAMP 1982 CHEVY® K10®

AXIC0286

AXI230048

AXI231021

AXIC0118

AXI231008

AXI231048

AXIC0114

AXIC0146

AXI231017

AXI231049

AXI231015

AXI231049

AXIC0114

AXIC0146

AXIC0286

AXIC0286 AXI230048

AXIC0146

SPMSR315

SPMXSE1040

AXI231049

AXI231021

AXI231017

AXIC0146

AXIC1185

AXI231016

AXIC0118

AXIC0114

AXIC0115

AXI231048

AXI231016

AXI231046

AXIC0118

AXIC0146

AXIC1185

AXI231012

AXI235167

AXI231008

SPMS614

AXIC1009

CHASSIS

KAROSSERIE

CHÂSSIS

TELAIO

EXPLODED VIEWS // EXPLOSIONSZEICHNUNGEN // VUES ÉCLATÉES // VISTE ESPLOSE

AXI03030

SCX10™ III BASE CAMP 1982 CHEVY® K10®

AXI43016

AXI43018

PRO360000

AXI235098

LOS235035

BODY ASSEMBLY

KAROSSERIEMONTAGE

ENSEMBLE DE CARROSSERIE

GRUPPO CARROZZERIA

EXPLODED VIEWS // EXPLOSIONSZEICHNUNGEN // VUES ÉCLATÉES // VISTE ESPLOSE

AXI03030

SCX10™ III BASE CAMP 1982 CHEVY® K10®

AXI233032

AXI234033

AXI233031 AXI233003

AXIC0392 AXI233031

AXI233033

AXI233032

AXIC0201

AXI233031

AXI233015

AXI235099

AXI234004

AXI233031

SHOCK ABSORBERS

STOSSDÄMPFER

AMORTISSEURS

AMMORTIZZATORI

PARTS LISTS // TEILELISTEN // LISTE DES PIÈCES // ELENCO COMPONENTI

Part # Description Beschreibung Description Descrizione

ARAC9759 AR722305 Flat Head Screw 3x5mm Sechskant-Flachkopfschraube,

M3 x 5mm Douille à six pans à tête plate

M3 x 5mm Vite a testa piana esagonale

M3 x 5mm

PRO360000 1982 Chevy K10 Clear Body Set w/

Scale Molded Accs

1982 Chevy K10 transparenter

Karosseriesatz w/Maßstabgetreu

geformtes Zubehör

Ensemble de carrosserie

transparente K10 Chevy 1982 avec

accessoires moulés à l’échelle

1982 Chevy K10 Clear Body Set

con accessori modellati in scala

AXI230047 DO FR/RR Bumper Set: SCX10 III BC DO FR/RR Stoßstangensatz: SCX10

III BC Jeu de pare-chocs AV/AR DO

SCX10 III BC Set paraurti anteriore/posteriore:

SCX10 III BC

AXI230048 Body Post Set: SCX10 III BC Gehäusestangensatz: SCX10 III BC Ens poteaux carrosserie: SCX10

III BC Set supporti scocca: SCX10 III BC

AXI231008 BatteryTray Set/Strap: SCX10 III Akkuhalterungsätze und Riemen Ensembles de supports de batterie

avec sangle Fascette e set supporto batteria

AXI231009 Upper Center Lnk Mnts: SCX10 III Obere mittige Gestängehalterungen Supports pour tringlerie centrale

supérieure Supporti braccetti centrali

superiori

AXI231010 Cntr Trans Skid Plate: SCX10 III Mittiges Getriebe-Gleitbrett Plaque de protection pour

transmission centrale Piastra proteggi trasmissione

centrale

AXI231011 Str Mnt Chassis Brace: SCX10 III Lenkhalterung Karosseriestrebe Support de châssis de direction Sostegno telaio supporto sterzo

AXI231012 Servo Horn, Metal 23T: SCX10 III Servohorn, Metall 23T Renvoi de commande de servo,

métal 23T Squadretta servo, Metallo 23T

AXI231015 Frame Rail Set: SCX10 III Rahmenschienensatz Ensemble de rails du cadre Set guida telaio

AXI231016 Bmpr/Bdy Mnts Chs FR/RR:SCX10 II Stoßstange/Gehäusehalterung

Karosserie Front/Heck Châssis avec supports de pare-

chocs et de carrosserie AV/AR Telaio supporti carrozzeria/

ammortizzatore FR/RR

AXI231017 Shktwrs&Pnhrd Mnts Fr/RRSCX10 II Stoßdämpferbrücken und Panhard-

Halterungen Front/Heck Tours d’amortisseurs et supports

Panhard AV/AR Torre ammortizzatore e supporti

Panhard FR/RR

AXI231018 Receiver Box: SCX10 III Empfängerbox Boîtier de récepteur Scatola ricevitore

AXI231021 Upper Shk Twr Braces: SCX10 III Obere Stoßdämpferbrückenstreben Supports de tours d’amortisseurs

supérieures Sostegni torre ammortizzatore

superiori

AXI231047 Skd Plt &Upr Lnk Mnt:SCX10 III BC Gleitbrett & Obere

Verbindungshalterung:SCX10 III BC Plq trans et sup tringlerie centr

sup: SCX10 III BC Sottoscocca & supporti bracci

superiori: SCX10 III BC

AXI231048 Servo Mnt Brace FR: SCX10 III BC Servohalterungsstrebe vorne: SCX10

III BC Support Servo FR: SCX10 III BC Bracci supporto servo ant: SCX10

III BC

AXI231049 Side Plate&Rr Brace: SCX10 III BC Seitenplatte & Strebe hinten: SCX10

III BC Plaque latérale et support AR:

SCX10 III BC Piastre laterali e rinforzi

posteriori: SCX10 III BC

AXI232002 6-Bolt Differental Locker 6-Schrauben-Differenzial-Sicherung Blocage différentiel à 6 boulons Blocco differenziale 6 bulloni

AXI232003 6-Bolt Heavy Duty Gear Set 6-Schrauben-Schwerlast-

Zahnradsatz Ensemble d’engrenages haute

résistance à 6 boulons Set ingranaggio impieghi gravosi

6 bulloni

AXI232017 Wild Boar Driveshaft Set: UTB Wild Boar-Antriebswellensatz: UTB Ensemble d’arbres de transmission

Wild Boar : UTB Set albero di trasmissione Wild

Boar: UTB

AXI232018 12mm Hex Pin and Spacer (4): UTB 12-mm-Sechskantstift und

Abstandhalter (4): UTB Broche hexagonale 12mm et

entretoise (4) : UTB Distanziale e perno esagonale

12mm (4): UTB

AXI232024 AR45 Axl Hsng(Fr)SCX10 III AR45 Achsgehäuse, Front AR45 Carter d’essieu avant AR45 Allogg assale ant

AXI232025 AR45 Axl Hsng (Rr)SCX10 III AR45 Achsgehäuse, Heck AR45 Carter d’essieu arrière AR45 Allogg assale post

AXI232033 InputMtlGears 27,20,34T:SCX10 II Metallgetriebe Eingabe 27T, 20T

und 34T Engrenages métalliques d’entrée

27T, 20T et 34T Ingranaggi in metallo ingresso

27T, 20T e 34T

AXI232059 AR45 C-Hub (L-R): SCX10 III AR45 C-Hub AR45 Moyeu de support AR45 Supporto mozzo

AXI232060 AR45 Knuckle (L-R): SCX10 III AR45 Lenkrolle AR45 Rotule de direction AR45 Fuso a snodo

AXI232061 AR45 Unvrsl Axles (2): SCX10 III AR45 Universalachsensatz AR45 Ensemble d’essieux universels AR45 Set assale univ

AXI232062 AR45 Strght Axles (2): SCX10 III AR45 Gerade Achse (2) AR45 Essieu droit (2) AR45 Assale dritto (2)

AXI232064 Gear Cover & Trans Housing: LCXU Fahrwerkabdeckung & Trans-

Gehäuse: LCXU Cache d’engrenageet carter

transmission: LCXU Carter e coperchio trasmissione:

LCXU

AXI232065 Spur Gear 56T 32P: LCXU Stirnrad, 56T, 32P: LCXU Engrenage roue droite, 56T, 32P:

LCXU Corona, 56T, 32P: LCXU

AXI232066 Motor Plate: LCXU Motorplatte: LCXU Plaque moteur: LCXU Piastra motore: LCXU

AXI232067 Slipper Elimintr Hub&Plate: LCXU Slipper-Eliminator-Nabe & -Platte:

LCXU Moyeu et plaque de sabot

éliminateur: LCXU Piastra e mozzo elimina

scorrimento: LCXU

AXI232068 Transmission Metal Gear Set: LCXU Metallgetriebesatz: LCXU Ensemble de boîte de transmission

métallique: LCXU Set ingr trasmissione metallo:

LCXU

AXI232069 Transmission Shaft Set: LCXU Getriebewellensatz: LCXU Ensemble arbre de transmission:

LCXU Set alberi trasmissione: LCXU

AXI232070 Trans Center Output Shaft: LCXU Transzentrale Antriebswelle: LCXU Arbre sortie transmis centrale:

LCXU Albero uscita trasmissione

centrale: LCXU

AXI233003 Shock O-Ring Set: UTB O-Ring-Satz für den Stoßdämpfer:

UTB Ensemble de joints toriques

d’amortisseur : UTB Set O-Ring ammortizzatore: UTB

AXI233009 Spring 13x70mm 2.0 lbs/in Ylw(2 Feder 13 x 70 mm 2 lbs/in Gelb (2) Ressort 13 x 70 mm 2 lb/po jaune (2) Molla 13 x 70 mm 2 lbs/in Giallo (2)

AXI233031 Shock Part Composite:SCX10 III BC Stoßdämpferteile, gegossen Pièces de l’amortisseur moulées Parti ammortizzatore stampate

AXI233032 Alum Shck Bdy11x39.5:SCX10 III BC Gewinde-Stoßdämpfergehäuse

Alum 11 x 39,5 mm Corps d’amortisseur ﬁleté

aluminium 11 x 39,5 mm Scocca ammortizzatore ﬁlettata

in alluminio 11x39,5 mm

AXI234003 Pvt Ball,Stainless12.75mm(4):UTB Kugelzapfen, Edelstahl 12,75 mm

(4): UTB Rotule, acier inoxydable 12,75mm

(4) : UTB Pivot ball, inossidabile, 12,75mm

(4): UTB

AXI234004 Susp Pvt Ball, Stainless 7.5mm Kugelzapfen für Federung, Edelstahl

7,5 mm Rotule de suspension, acier

inoxydable 7,5mm Pivot ball sospensioni,