Losi LOS03028T1 Le manuel du propriétaire

Catégorie
Jouets télécommandés
Taper
Le manuel du propriétaire
Before operating this vehicle, please read all printed materials thoroughly.
Horizon Hobby is not responsible for inadvertent errors in this manual.
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
MANUEL D’UTILISATION
MANUALE DI ISTRUZIONI
LASERNUT TENACITY ULTRA 4 ROCK RACER
1/10
th
Scale 4WD RTR
EN
2
LOSI
®
TENACITY
®
LASERNUT ULTRA 4 1/10 4WD RTR ROCK RACER • INSTRUCTION MANUAL
Age Recommendation: Not for children under 14 years. This is not a toy.
WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to
the product, personal property and cause serious injury.
This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this Product in a safe and
responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. Do not use with
incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance.
It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.
WARNING AGAINST COUNTERFEIT PRODUCTS Always purchase from a Horizon Hobby, LLC authorized dealer to ensure authentic high-quality Spektrum product.
Horizon Hobby, LLC disclaims all support and warranty with regards, but not limited to, compatibility and performance of counterfeit products or products claiming compatibility with
DSM or Spektrum technology.
NOTICE
All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby,LLC. For up-to-date product literature, visit www.horizonhobby.com
or www.towerhobbies.com and click on the support or resources tab for this product.
MEANING OF SPECIAL LANGUAGE
The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:
WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of superficial injury.
CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.
NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no possibility of injury.
As the user of this product, you are solely responsible for operating in a manner that does not
endanger yourself and others or result in damage to the product or property of others.
This model is controlled by a radio signal subject to interference from many sources outside
your control. This interference can cause momentary loss of control, so it is advisable to
always keep a safe distance in all directions around your model as this margin will help avoid
collisions or injury.
• Never operate your model with low transmitter batteries.
• Always operate your model in open spaces away from full-size vehicles, traffic and people.
• Never operate the model in the street or in populated areas for any reason.
• Carefully follow the directions and warnings for this and any optional support equipment
(chargers, rechargeable battery packs, etc.) you use.
Keep all chemicals, small parts and anything electrical out of the reach of children.
• Never lick or place any portion of the model in your mouth as it could cause serious injury
or even death.
• Exercise caution when using tools and sharp instruments.
• Take care during maintenance as some parts may have sharp edges.
• Immediately after using your model, do NOT touch equipment such as the motor, electronic
speed control and battery, because they generate high temperatures. You may burn yourself
seriously touching them.
• Do not put fingers or any objects inside rotating and moving parts, as this may cause
damage or serious injury.
Always turn on your transmitter before you turn on the receiver in the car. Always turn off the
receiver before turning your transmitter off.
• Keep the wheels of the model off the ground when checking the operation of the radio
equipment.
SAFETY PRECAUTIONS AND WARNINGS
TABLE OF CONTENTS
BOX CONTENTS ........................................................................................................3
COMPONENTS ..................................................................................................................3
SPEKTRUM SMART TECHNOLOGY .....................................................................................3
WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS ..............................3
GENERAL PRECAUTIONS ................................................................................................... 3
WET CONDITIONS MAINTENANCE ....................................................................................3
QUICK START ............................................................................................................3
CHARGING THE BATTERY .........................................................................................3
INSTALLING THE BATTERY ........................................................................................ 4
TRANSMITTER FUNCTIONS ......................................................................................4
TRANSMITTER BATTERY INSTALLATION .............................................................................4
SR6100AT AVC TECHNOLOGY TELEMETRY RECEIVER AUX CHANNELS ...............................5
BINDING AND CALIBRATING THE RECEIVER ............................................................5
DISABLING AVC
®
TECHNOLOGY STABILITY ASSIST.............................................................5
FAILSAFE ..........................................................................................................................5
DRIVING PRECAUTIONS ..........................................................................................5
POWERING ON THE VEHICLE .................................................................................... 5
BEFORE RUNNING THE VEHICLE ............................................................................... 5
AVC
®
SENSITIVITY .................................................................................................... 5
RUN TIME ................................................................................................................. 6
TO IMPROVE RUN TIMES ...................................................................................................6
PERFORMING A CONTROL DIRECTION TEST.............................................................6
CHANGING THE TRAVEL ADJUST SETTINGS .............................................................6
SPEKTRUM
FIRMA
SMART 130A BRUSHLESS ESC (SPMXSE1130) .......................6
SPECIFICATIONS ...............................................................................................................6
ESC LED STATUS ...............................................................................................................6
AUDIBLE WARNING TONES ...............................................................................................6
ESC CALIBRATION PROCEDURE ........................................................................................6
ESC FUNCTIONS AND MODES ...........................................................................................7
PROGRAMMING TABLE ..................................................................................................... 7
ESC PROGRAMMING PROCEDURE ....................................................................................7
DESCRIPTIONS ..................................................................................................................7
SPEKTRUM™ FIRMA™ 1900KV BRUSHLESS MOTOR ..............................................8
PRECAUTIONS ..................................................................................................................8
GEARING ......................................................................................................................... 8
CHANGING THE PINION GEAR/GEAR RATIO ......................................................................8
SETTING THE GEAR MESH .................................................................................................8
TELEMETRY SETTINGS ....................................................................................................... 8
TROUBLESHOOTING GUIDE ......................................................................................8
LIMITED WARRANTY ............................................................................................... 8
WARRANTY AND SERVICE CONTACT INFORMATION ................................................9
FCC INFORMATION ..................................................................................................9
IC INFORMATION .....................................................................................................9
COMPLIANCE INFORMATION FOR THE EUROPEAN UNION ......................................9
REPLACEMENT PARTS ......................................................................................34–35
RECOMMENDED PARTS..........................................................................................36
OPTIONAL PARTS ...................................................................................................36
EXPLODED VIEW ..............................................................................................37–41
3
EN
LOSI
®
TENACITY
®
LASERNUT ULTRA 4 1/10 4WD RTR ROCK RACER • INSTRUCTION MANUAL
BOX CONTENTS
Your new Horizon Hobby vehicle has been designed and built with a combination of
waterproof and water-resistant components to allow you to operate the product in many
“wet conditions,” including puddles, creeks, wet grass, snow and even rain.
While the entire vehicle is highly water-resistant, it is not completely waterproof and your vehicle
should NOT be treated like a submarine. The various electronic components used in the vehicle,
such as the Electronic Speed Control (ESC), servo(s) and receiver are waterproof, however, most
of the mechanical components are water-resistant and should not be submerged.
Metal parts, including the bearings, hinge pins, screws and nuts, as well as the contacts in the
electrical cables, will be susceptible to corrosion if additional maintenance is not performed
after running in wet conditions. To maximize the long-term performance of your vehicle and
to keep the warranty intact, the procedures described in the “Wet Conditions Maintenance”
section below must be performed regularly if you choose to run in wet conditions. If you are
not willing to perform the additional care and maintenance required, then you should not
operate the vehicle in those conditions.
CAUTION: Failure to exercise caution while using this product and complying with the
following precautions could result in product malfunction and/or void the warranty.
GENERAL PRECAUTIONS
• Read through the wet conditions maintenance procedures and make sure that you have all
the tools you will need to properly maintain your vehicle.
• Not all batteries can be used in wet conditions. Consult the battery manufacturer before
use. Caution should be taken when using Li-Po batteries in wet conditions.
• Most transmitters are not water-resistant. Consult your transmitter’s manual or the
manufacturer before operation.
• Never operate your transmitter or vehicle where lightning may be present.
• Do not operate your vehicle where it could come in contact with salt water (ocean water or
water on salt-covered roads), contaminated or polluted water. Salt water is very conductive
and highly corrosive, so use caution.
• Even minimal water contact can reduce the life of your motor if it has not been certified as
water-resistant or waterproof. If the motor becomes excessively wet, apply very light throttle
until the water is mostly removed from the motor. Running a wet motor at high speeds may
rapidly damage the motor.
Driving in wet conditions can reduce the life of the motor. The additional resistance of
operating in water causes excess strain. Alter the gear ratio by using a smaller pinion or larger
spur gear. This will increase torque (and motor life) when running in mud, deeper puddles, or
any wet conditions that will increase the load on the motor for an extended period of time.
WET CONDITIONS MAINTENANCE
• Drain any water that has collected in the tires by spinning them at high speed. With the
body removed, place the vehicle upside down and pull full throttle for a few short bursts
until the water has been removed.
CAUTION: Always keep hands, fingers, tools and any loose or hanging objects
away from rotating parts when performing the above drying technique.
• Remove the battery pack(s) and dry the contacts. If you have an air compressor or a can of
compressed air, blow out any water that may be inside the recessed connector housing.
• Remove the tires/wheels from the vehicle and gently rinse the mud and dirt off with a
garden hose. Avoid rinsing the bearings and transmission.
NOTICE: Never use a pressure washer to clean your vehicle.
• Use an air compressor or a can of compressed air to dry the vehicle and help remove any
water that may have gotten into small crevices or corners.
• Spray the bearings, drive train, fasteners and other metal parts with a water-displacing light
oil. Do not spray the motor.
Let the vehicle air dry before you store it. Water (and oil) may continue to drip for a few hours.
• Increase the frequency of disassembly, inspection and lubrication of the following:
- Front and rear axle hub assembly bearings.
- All transmission cases, gears and differentials.
- Motor—clean with an aerosol motor cleaner and re-oil the bushings with lightweight
motor oil.
WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS
QUICK START
Please read the entire manual to gain a full understanding of the LASERNUT U4 RTR vehicle, fine-tuning the setup and performing maintenance.
1. Read the safety precautions found in this manual.
2. Charge a battery for the vehicle. Refer to the included charging warnings and
instructions for battery charging information.
3. Install the AA batteries in the transmitter. Only use alkaline
or rechargeable batteries.
4. Install the fully charged battery in the vehicle.
5. Power ON the transmitter and then the vehicle. Wait 5 seconds for the ESC
to initialize. Always power the transmitter ON before the vehicle and power
it OFF after the vehicle has been powered OFF.
6. Check the steering and throttle control directions. Verify that the servos are
moving in the correct direction.
7. Drive your vehicle.
8. Perform any necessary maintenance.
CHARGING THE BATTERY
The Lasernut Ultra 4 includes Spektrum SMART Technology in the ESC and receiver, which can
provide you with telemetry information including battery voltage and vehicle temperature.
To take advantage of SMART Technology, you’ll need a SMART compatible transmitter. The
included DX3 Active transmitter can be upgraded with the Spektrum Bluetooth Module
(SPM6741) Or, consider upgrading to a SMART Technology compatible Spektrum transmitter
like the DX5C (SPMR5100–transmitter only), DX5 Pro (SPMR5010–transmitter only), or DX5
Rugged (SPM5200–includes SR515 receiver). Use Spektrum SMART batteries to power your
vehicle to take full advantage of SMART Technology, which can communicate battery data
through the SMART system as well.
Visit www.SpektrumRC.com for more information.
SPEKTRUM SMART TECHNOLOGY
COMPONENTS
• Losi
®
Tenacity
®
Lasernut Ultra 4 1/10-Scale 4WD RTR Rock Racer
• Spektrum
DX3
SMART Transmitter (SPMR2340)
• Spektrum SR6100AT 6 Channel AVC Telemetry Surface Receiver (SPMSR6100AT)
• Spektrum
15KG 23T Waterproof Metal Center Case Servo (SPMS614)
• Spektrum Firma
SMART 130A Brushless ESC (SPMXSE1130)
• 3668 - 1900Kv BL 4 Pole Motor (SPMXSM2200)
• 4 AA batteries (for transmitter)
Choose a battery designed to work with the Spektrum
Firma
SMART 130A Brushless ESC
(SPMXSE1130). We recommend the Spektrum 5000mAh 3S 11.1V 50C SMART LiPo hardcase
battery with IC5
®
connector (SPMX50003S50H5) or Spektrum 5000mAh 4S 14.8V 50C SMART
LiPo IC5 hardcase battery with IC5 connector (SPMC50004S50H5). Choose a charger designed
to charge 3S and/or 4S Li-Po batteries.
We recommend the Spektrum SMART dual-output AC charger, 2x100W (SPMXC1010).
Refer to your battery and charger manuals for usage, safety, and charging information.
IMPORTANT: When using a 3S battery, you must change the motor pinion gear to the 14T
pinion provided with your vehicle.
EN
4
LOSI
®
TENACITY
®
LASERNUT ULTRA 4 1/10 4WD RTR ROCK RACER • INSTRUCTION MANUAL
INSTALLING THE BATTERY
TRANSMITTER FUNCTIONS
A/B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
L.
M.
N.
Channel 3 Button
Throttle/Brake
Steering Wheel
Steering Rate
Adjusts the end point of the steering
Brake Rate
Adjusts the braking end point.
Steering Trim
Adjusts the steering center point. Normally, the steering trim is adjusted until the vehicle tracks straight.
Throttle Trim
Adjusts the throttle neutral point
SMART Battery Level Indicator
Servo Reversing
To reverse the Throttle (TH) or Steering (ST) channel, switch the position of the correlating switch—
“N” is for normal, “R” is for reverse.
Throttle Limit
Limits throttle output to 50/75/100%
Select 50% or 75% for less experienced drivers or when you are driving the vehicle in a small area.
Power LED
Solid red lights: Indicates radio connectivity and adequate battery power
Flashing red lights: Indicates the battery voltage is critically low. Replace batteries
Power Button
Bind Button
This transmitter requires 4 AA batteries
1. Remove the battery cover from the transmitter.
2. Install the batteries as shown.
3. Install the battery cover.
CAUTION: Never remove the transmitter batteries while the
model is powered ON. Loss of model control, damage, or injury may
occur.
CAUTION: If using rechargeable batteries, charge only
rechargeable batteries. Charging non-rechargeable batteries may
cause the batteries to burst, resulting in injury to persons and/or damage
to property.
CAUTION: Risk of explosion if battery is replaced by an incorrect
type. Dispose of used batteries according to national regulations.
TRANSMITTER BATTERY INSTALLATION
C
D
H
J
K
L
I
G
F
E
M
N
A/B
1. Ensure the ESC is powered OFF.
2. Remove the body clips and rotate the body up.
3. Undo the hook and loop straps.
4. Insert the battery into the battery tray.
5. Secure the hook and loop straps.
6. Connect the battery power lead to the ESC, noting proper polarity.
7. Power ON the transmitter, then the vehicle.
8. Rotate the body into place, and insert the body clips.
IMPORTANT: Secure the ESC wires so they do not interfere with the gearing.
NOTICE: If you are using a 3S Li-Po battery, use the included 14T pinion
gear. If you are using a 4S Li-Po battery, use the installed 12T pinion gear.
Using a 14T pinion gear with a 4S Li-Po battery will result in damage to
the ESC and motor.
5
EN
LOSI
®
TENACITY
®
LASERNUT ULTRA 4 1/10 4WD RTR ROCK RACER • INSTRUCTION MANUAL
DRIVING PRECAUTIONS
• Maintain sight of the vehicle at all times.
• Routinely inspect the vehicle for loose wheel hardware.
• Routinely inspect the steering assembly for any loose hardware. Driving the vehicle off-road
can cause fasteners to loosen over time.
• Do not drive the vehicle in tall grass. Doing so can damage the vehicle or electronics.
• Stop driving the vehicle when you notice a lack of power. Driving the vehicle when the
battery is discharged can cause the receiver to power off. If the receiver loses power, you
will lose control of the vehicle. Damage due to an over-discharged Li-Po battery is not
covered under warranty.
CAUTION: Do not discharge a Li-Po battery below 3V per cell. Batteries discharged
to a voltage lower than the lowest approved voltage may become damaged,
resulting in loss of performance and potential fire when batteries are charged.
• Do not apply forward or reverse throttle if the vehicle is stuck.
Applying throttle in this instance can damage the motor or ESC.
• After driving the vehicle, allow the electronics to cool before driving the vehicle again.
IMPORTANT: Keep wires away from all moving parts.
POWERING ON THE VEHICLE
1. Center the ST TRIM and TH TRIM dials on the transmitter.
2. Power on the transmitter.
3. Install a fully charged battery pack per the
Installing the Battery
section.
4. Power on the ESC.
IMPORTANT: The vehicle MUST remain on a flat, level surface and motionless
for at least 5 seconds.
BEFORE RUNNING THE VEHICLE
1. Check for free suspension movement. All suspension arms and steering components should
move freely. Any binds will cause the vehicle to handle poorly.
TIP: To increase the ride height and ground clearance of your vehicle, screw down the
shock collars to compress the springs.
2. Charge a battery pack. Always charge the battery pack as per the battery and/or charger
manufacturers’ instructions.
3. Set the transmitter steering trim. Follow the instructions to set the steering trim/subtrim so
that the vehicle drives straight with no input to the steering.
4. Perform a Control Direction Test.
AVC
®
SENSITIVITY
The ST RATE dial adjusts the sensitivity, or stability, value in the receiver. If you increase the
sensitivity, the AVC
®
system becomes more sensitive to the vehicle drifting left or right. You
would use maximum sensitivity during high speed driving or drag racing, when you want the
vehicle to stay in a straight line.
Turn the ST RATE knob counter-clockwise to reduce the sensitivity.
Turn the ST RATE knob clockwise to increase the sensitivity.
IMPORTANT: The ST RATE knob will only adjust the sensitivity when the
transmitter is bound to a DSMR
®
receiver. When the transmitter is bound
to a DSM
®
, DSM2
®
or DSM Marine receiver, the ST RATE knob controls
the steering dual rate.
BINDING AND CALIBRATING THE RECEIVER
Binding is the process of linking the SR6100AT receiver to your Spektrum transmitter. The AVC
features on the receiver can be enabled or disabled during the binding process.
IMPORTANT: You must calibrate the SR6100AT receiver each time it is placed in bind mode,
regardless of AVC being enabled or disabled.
Upon initial setup after the first bind, the model must be configured for servo direction, trim
and travel. Then the receiver must be rebound and calibrated to those settings for proper
operation. Center the steering trim and throttle trim on the transmitter before beginning.
1. Press and hold the bind button on the receiver.
2. Power on the receiver. The orange LED flashes, indicating the receiver is in bind mode.
Release the bind button after the orange LED illuminates.
3. Put your transmitter in bind mode. The bind process is complete when the orange LED
on the receiver remains lit. The receiver is now bound to the transmitter but must be
calibrated before it will operate.
4. Pull the transmitter trigger to full throttle, pause, then return the trigger to center.
5. Push the transmitter trigger to full brake, pause, then return the trigger to center.
6. Turn the transmitter steering wheel to full right, pause, then return the wheel to center.
7. Turn the transmitter steering wheel to full left, pause, then return the steering wheel to
center. The orange LED flashes to confirm the settings have been accepted.
8. Turn off the vehicle to complete the binding and calibration process.
CAUTION: When the bind process is complete, the throttle and steering channels
are active. Keep hands and loose objects away from all spinning parts on the
vehicle.
IMPORTANT: You must rebind the transmitter and receiver if you:
• Change the servo reversing after binding
• Change the travel after binding
• Change the receiver mounting orientation
DISABLING AVC
®
TECHNOLOGY STABILITY ASSIST
If you participate in organized racing, you may be required to turn AVC technology off.
To turn off AVC technology:
1. Connect power to the receiver and quickly press and release the bind button three times
(within 1.5 seconds).
2. Press and hold the bind button and to put the receiver in bind mode. release the buton
when the LED starts to flash rapidly, indicating it is in bind mode.
When the AVC system has been disabled, the LED on the receiver will show three flashes
upon power up, and then remain lit. The receiver is bound and operating normally when the
LED remains illuminated.
TIP: If the AVC feature in the receiver is active and the AVC menu in the transmitter is
Inhibited, AVC functions will default to the AUX 1 and AUX 2 operation, and in this scenario,
AVC will not work correctly.
FAILSAFE
In the unlikely event that the radio link is lost during use, the receiver will drive the throttle
channel to the neutral position. If the receiver is powered on prior to turning on the
transmitter, the receiver will enter the failsafe mode, driving the throttle channel to the neutral
position. When the transmitter is turned on, normal control is resumed.
IMPORTANT: Failsafe activates only in the event that signal is lost from the transmitter.
Failsafe will NOT activate in the event that receiver battery power decreases below the
recommended minimums or power to the receiver is lost.
SR6100AT AVC TECHNOLOGY TELEMETRY RECEIVER
AUX CHANNELS
The Aux channels can operate as additional servo channels, or as a power supply
for a personal transponder.
If AVC is active, only 4 channels; Steering, Throttle, AUX3 and AUX4 are operational.
The reaming Aux channels can be used to power a personal transponder or lights.
If AVC is disabled (see DISABLING AVC TECHNOLOGY STABILITY ASSIST FUNCTION),
all 6 channels including the Aux channels can operate as servo channels.
AUX 1 Port
AUX 2 Port
AUX 3 Port
AUX 4 Port
Battery/Programming Port
Throttle Port
Steering Port
Bind Button
FULL THROTTLE
BRAKE/REVERSE
EN
6
LOSI
®
TENACITY
®
LASERNUT ULTRA 4 1/10 4WD RTR ROCK RACER • INSTRUCTION MANUAL
EN
RUN TIME
The largest factor in run time is the capacity of the battery pack. A larger mAh rating increases
the amount of run time experienced.
The condition of a battery pack is also an important factor in both run time and speed.
The battery connectors may become hot during driving. Batteries will lose performance
and capacity over time.
Driving the vehicle from a stop to full speed repeatedly will damage the batteries
and electronics over time. Sudden acceleration will also lead to shorter run times.
TO IMPROVE RUN TIMES
• Keep your vehicle clean and well maintained.
• Allow more airflow to the ESC and motor.
• Change the gearing to a lower ratio. A lower ratio decreases the operating temperature
of the electronics. Use a smaller pinion gear or larger spur gear to lower the gear ratio.
• Use a battery pack with a higher mAh rating.
• Use the optimum charger to charge battery packs (Visit your local hobby dealer for
more information).
PERFORMING A CONTROL DIRECTION TEST
Perform a control test with the vehicle wheels off the ground. If the wheels rotate after the
vehicle is powered ON, adjust the TH Trim knob until they stop. To make the wheels move
forward, pull the trigger. To reverse them, wait for the wheels to stop, then push the trigger.
When moving forward, the wheels should maintain a straight line without any steering wheel
input. If not, adjust the ST Trim knob, so the wheels maintain a straight line without having to
turn the steering wheel.
CHANGING THE TRAVEL ADJUST SETTINGS
Set the travel adjust settings with all four vehicle wheels off the ground. The throttle end point
and brake end point adjustments will cause the wheels to spin at full speed. Have an assistant
safely hold the vehicle securely while adjusting these settings.
CAUTION: Keep hands, hair and all loose clothing away from any moving parts,
especially the wheels, while setting the travel adjust end points. Serious injury may result.
1. Hold the trigger in the full brake position and turn the steering wheel to full right while powering
on the transmitter. The LED flashes rapidly, indicating programming mode is active.
2. Throttle End Point: Continue holding full throttle. Turn the TH TRIM knob to adjust the full
throttle end point.
3. Brake End Point: Hold the trigger in the full brake position. Turn the TH TRIM knob to adjust
the full brake end point. Return the trigger to the center position.
4. Left Steering End Point: Hold the steering wheel in the full left position. Turn the ST TRIM
knob to adjust the left end point.
5. Right Steering End Point: Hold the steering wheel in the full right position. Turn the ST TRIM
knob to adjust the right end point. Return the steering wheel to the center position.
6. Power off the transmitter to save the travel adjust settings.
The minimum Travel is 75%, and the Maximum travel is 150%.
IMPORTANT: If the travel is changed on the DX2E, you must rebind and calibrate the SRS6100AT.
SPECIFICATIONS
Type Sensorless, SMART Throttle Compatible
Output 130A/760A
Function Forward/Brake–Forward/Brake Reverse
Input Voltage 7.4V–14.8V
BEC Output 6V/4A
Dimensions (LxWxH) 57.5mm x 46mm x 38mm
Weight 154 g
ESC LED STATUS
• No ESC LEDs will glow when there is no throttle input from the transmitter.
• The red ESC LED glows when there is any throttle input from the transmitter.
AUDIBLE WARNING TONES
1. Input Voltage: The ESC checks the in put voltage when it is powered ON. If a voltage
problem is detected, the ESC continuously sounds 2 beeps with a 1 second pause
(xx-xx-xx). Power OFF the ESC and ensure the connections are secure and that
the battery power is not too low for safe operation.
2. Radio Connection: The ESC checks radio signal input when it is powered ON.
If a problem is detected, the ESC continuously sounds 1 beep with a 2 second pause
(x--x--x). Power OFF the ESC and ensure the radio system is operating correctly.
NOTICE: Always disconnect the battery from the ESC after operating your vehicle. The ESC’s
switch only controls power to the receiver and servos. The ESC will continue to draw current when
connected to the battery, resulting in possible damage to the battery through over discharge.
ESC CALIBRATION PROCEDURE
Complete the transmitter/receiver binding procedure prior to calibrating the ESC.
1. Set the transmitter throttle channel to 100% travel and center the throttle trim.
2. Connect a battery to the ESC battery lead.
3. Power on the transmitter.
4. Press and hold the SET button while turning on the ESC. Release the SET button when
the red LED begins to flash, indicating the ESC is in calibration mode. The ESC will enter
programming mode if the button is held for more than three seconds.
TIP: The red LED should be flashing when the ESC enters calibration mode. If the green LED
is flashing the ESC has entered programming mode. Power off the ESC and repeat step 4,
releasing the SET button when the red LED begins to flash.
5. With the transmitter throttle trigger at the neutral position, press and release the ESC SET
button. The red LED will stop flashing, the green LED will flash one time and the motor will
make a tone to indicate the neutral position has been accepted.
6. While holding the throttle trigger at the full throttle position, press and release the ESC SET
button. The green LED will flash twice and the motor will make two tones to indicate the full
throttle position has been accepted.
7. While holding the throttle trigger at the full brake position, press and release the SET button.
The green LED will flash three times and the motor will make three tones to indicate the full
brake position has been accepted.
The motor will operate normally after calibration is completed.
SPEKTRUM
FIRMA
SMART 130A BRUSHLESS ESC (SPMXSE1130)
7
EN
LOSI
®
TENACITY
®
LASERNUT ULTRA 4 1/10 4WD RTR ROCK RACER • INSTRUCTION MANUAL
DESCRIPTIONS
1. Running Mode
- Forward Only with Brake
Intended for competition use, this mode allows only forward and brake controls.
- Forward/Reverse with Brake
This mode is the basic all-around mode, allowing forward, reverse and brake controls.
To engage reverse while moving forward, apply the brake until the vehicle has come to
a complete stop, release brake, then apply the brake again. While braking or in reverse,
engaging the throttle will result in the vehicle immediately accelerating forward.
2. Drag Brake Force
Adjusts the amount of brake automatically applied when the throttle is returned to the
neutral position. This simulates the engine braking effect of a full-scale vehicle, allowing
improved turn-in and your vehicle’s general response to controls.
3. Low Voltage Cutoff
This function helps to prevent battery over-discharge. The ESC continuously monitors the
battery’s voltage. If the voltage falls below the voltage threshold for 2 seconds, the output
power shuts off and the red LED flashes twice repeatedly.
The cutoff threshold calculation is based on individual Li-Po cell voltage. For Ni-MH batteries,
if the voltage battery pack is higher than 9.0V, it will be treated as a 3-cell Li-Po battery
pack; if it is lower than 9.0V, it will be treated as a 2-cell Li-Po battery pack. Example: for a
8.0V Ni-MH battery pack used with a 2.6V/cell threshold, it will be treated as a 2-cell Li-Po
battery pack and the low-voltage cut-off threshold will be 5.2V (2.6x2=5.2).
4. Start Mode (Punch)
Sets the initial throttle punch when the car accelerates. Level 1 gives
a very soft initial acceleration and level 4 gives a stronger initial acceleration.
5. Max Brake Force
Adjusts the maximum braking force. A higher value provides stronger braking,
but can also cause the wheels to lock, resulting in loss of control of the car.
6. Max Reverse Force
This parameter adjusts the maximum power when travelling in reverse.
7. Initial Brake Force (minimum brake)
Adjusts the minimum amount of braking power when the brakes engage. The default value
is equal to the drag brake value. A high value can lock the wheels when the brake is used.
8. Neutral Range
Adjusts the throttle sensitivity around the neutral point. A higher value results in the
throttle having to be moved more for the vehicle to move forward, backward or brake.
9. Timing
Adjusts the motor drive current timing. More timing gives more performance, but can
lower efficiency and cause damage to the motor and/or ESC by overload or overheating.
NOTICE: Always ensure the motor timing is set correctly. Failure to set the motor timing
correctly can result in damage to the motor and ESC. Refer to the manufacturer instructions
for recommended timing settings.
10. Motor Type
11. Motor Rotation
Allows you to make this change in the ESC so no wires need to be changed between the
ESC and the motor.
12. Li-Po Cells
Allows the ESC to automatically detect or manually set the number of cells in your Li-Po
battery back.
Default Settings
ESC FUNCTIONS AND MODES
The ESC includes programming options so you can adjust the way your vehicle performs. Refer to the included programming table to adjust the ESC for your driving conditions.
PROGRAMMING TABLE
PROGRAMMING VALUE
PROGRAMMING ITEMS 1 2 3 4 5 6 7 8 9
1. Running Mode Forward w/ brake
Forward/Reverse
w/ brake
Forward/Reverse
2. Drag Brake Force 0% 5% 10% 20% 40% 60% 80% 100%
3. Low Voltage Cutoff non-protection 2.6V/Cell 2.8V/Cell 3.0V/Cell 3.2V/Cell 3.4V/Cell
4. Start Mode Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 Level 7 Level 8 Level 9
5. Max Brake Force 25% 50% 75% 100% disable
6. Max Reverse Force 25% 50% 75% 100%
7. Initial Brake Force = Drag Brake 0% 20% 40%
8. Neutral Range 6% (Narrow) 9% (Normal) 12% (Wide)
9. Timing 0.00º 3.75º 7.50º 11.25º 15.00º 18.75º 22.50º 26.25º
10. Motor Rotation Counterclockwise Clockwise
11. Li-Po Cells Auto Calculate 2 Cells 3 Cells 4 Cells 5 Cells 6 Cells
ESC PROGRAMMING PROCEDURE
Programming is accomplished using the SET button on the ON/OFF switch*.
1. Connect a fully charged battery to the ESC.
2. Power on the transmitter.
3. Power on the ESC.
4. Hold the SET button until the green LED flashes. Release the set button to enter
programming mode.
TIP: To reset all programming items to the default values, press and hold the set button for
five seconds
5. Press and release the set button as needed to cycle through the programming items. The
number of times the green LED flashes equals the programming item number given in the
programming table.
6. When at the desired programming item, press and hold the set button until the red LED
flashes to select the item.
7. Press and release the SET button to cycle through the values available for the programming
item based on the number of times the LED flashes. Refer to the programming table.
8. Save the setting by pressing and holding the SET button for 3 seconds.
9. Power off the ESC to exit programming mode or to change other programming items.
* Other programming options include the Spektrum SMART Firma ESC Programming Box (SPMXCA200) and the SmartLink USB updating and programmer application. See SpektrumRC.com for
more details about Spektrum SMART Firma ESCs.
EN
8
LOSI
®
TENACITY
®
LASERNUT ULTRA 4 1/10 4WD RTR ROCK RACER • INSTRUCTION MANUAL
PRECAUTIONS
• Never touch moving parts.
• Never disassemble while the batteries are installed.
• Always let parts cool before touching.
GEARING
Your vehicle has been equipped with the optimal gearing installed for the use of a 4S battery.
It offers an ideal balance between speed, power and efficiency. Should you decide to
customize your vehicle with a 3S battery it is necessary to change to the 14T pinion (included).
Installing a pinion gear with fewer teeth or a spur gear with more teeth will provide greater
torque but will reduce top speed. Likewise, a pinion gear with more teeth or a spur gear with
fewer teeth will reduce torque and increase top speed. Care should be taken when installing
larger pinion gears as this can "overgear" the vehicle, resulting in overheating of the motor
and ESC. When testing different gearing options, pay close attention to the temperature
of the motor and speed control to ensure you are operating within the temperature range
of the components. The motor or ESC should never be so hot that it cannot be touched. If
temperatures are too hot, a different gearing combination with a lower pinion gear and/or
higher spur gear is suggested.
CHANGING THE PINION GEAR/GEAR RATIO
1. Remove the screw holding the pinion gear cover in place.
2. Loosen the set screw and remove the installed pinion gear.
3. Loosen the motor screws and slide the motor back.
4. Place the new pinion on the end of the motor shaft so the set screw is located
over the flat on the shaft.
5. Position it so the teeth line up with the spur gear and secure the pinion by tightening
the set screw.
6. Set the gear mesh.
SPEKTRUM
FIRMA
1900KV BRUSHLESS MOTOR
SETTING THE GEAR MESH
The gear mesh has already been set at the factory. Setting it is only necessary when changing
motors or gears.
Proper gear mesh (how gear teeth meet) is important to the performance of the vehicle. When
the gear mesh is too loose, the spur gear could be damaged by the pinion gear of the motor. If
the mesh is too tight, speed could be limited and the motor and ESC will overheat.
1. Loosen the motor screws and slide the motor back.
2. Put a small piece of paper between the pinion and spur gears.
3. Push the gears together while tightening the motor screws.
4. Remove the paper. Check the mesh at 3–5 different locations around
the spur gear for a small amount of movement.
5. Install the gear cover.
NOTICE: If you are using a 3S Li-Po battery, use the included 14T Pinion gear. If you are
using a 4S Li-Po battery, use the installed 12T pinion gear. Using a 14T pinion gear with a
4S Li-Po battery will result in damage to the ESC and motor.
TELEMETRY SETTINGS
If using the Spektrum Dashboard app or the optional speedometer module on your
transmitter, set the motor pole count to 4 and the rollout distance to 1.5" (38.1mm).
TROUBLESHOOTING GUIDE
PROBLEM POSSIBLE CAUSE SOLUTION
Vehicle does not operate
Battery not charged or plugged in Charge battery/plug in
ESC switch not “On” Turn on ESC switch
Transmitter not “On” or low battery Turn on/replace batteries
Motor runs but wheels
do not rotate
Pinion not meshing with spur gear Adjust pinion/spur mesh
Pinion spinning on motor shaft Tighten pinion gear setscrew on motor shaft flat spot
Transmission gears stripped Replace transmission gears
Drive pin broken Check and replace drive pin
Steering does not work
Servo plug not in receiver properly Make sure the steering servo plug is connected to the receiver steering channel, noting proper polarity
Servo gears or motor damaged Replace or repair servo
Will not turn one direction Servo gears damaged Replace or repair servo
Motor does not run
Motor wire solder joint is damaged Resolder the motor wire with the proper equipment
Motor wire broken Repair or replace as needed
ESC damaged Contact Horizon Hobby Product Support
ESC gets hot
Motor over-geared Use smaller pinion or larger spur gear
Driveline bound up Check wheels and transmission for binding
Poor run time and/or sluggish
acceleration
Battery pack not fully charged Recharge battery
Charger not allowing full charge Try another charger
Driveline bound up Check wheels, transmission for binding
Poor range and/or glitching
Transmitter batteries low Check and replace
Vehicle battery low Recharge battery
Loose plugs or wires Check all wire connections and plugs
LIMITED WARRANTY
What this Warranty Covers
Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the
“Product”) will be free from defects in materials and workmanship for a period of 2 years from
the date of purchase.
What is Not Covered
This warranty is not transferable and does not cover (i) cosmetic damage, (ii) damage due
to acts of God, accident, misuse, abuse, negligence, commercial use, or due to improper use,
installation, operation or maintenance, (iii) modification of or to any part of the Product, (iv)
attempted service by anyone other than a Horizon Hobby authorized service center, (v) Product
not purchased from an authorized Horizon dealer, or (vi) Product not compliant with applicable
technical regulations or (vii) use that violates any applicable laws, rules, or regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY
OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES,
INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE PURCHASER
ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY
MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.
Purchaser’s Remedy
Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be that Horizon
will, at its option, either (i) service, or (ii) replace, any Product determined by Horizon to be
defective. Horizon reserves the right to inspect any and all Product(s) involved in a warranty
claim. Service or replacement decisions are at the sole discretion of Horizon. Proof of purchase
is required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS
WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.
Limitation of Liability
HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL
DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY,
REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, TORT,
NEGLIGENCE, STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the liability
of Horizon exceed the individual price of the Product on which liability is asserted. As Horizon
has no control over use, setup, final assembly, modification or misuse, no liability shall be
assumed nor accepted for any resulting damage or injury. By the act of use, setup or assembly,
the user accepts all resulting liability. If you as the purchaser or user are not prepared to
accept the liability associated with the use of the Product, purchaser is advised to return the
Product immediately in new and unused condition to the place of purchase.
9
EN
LOSI
®
TENACITY
®
LASERNUT ULTRA 4 1/10 4WD RTR ROCK RACER • INSTRUCTION MANUAL
Country of Purchase Horizon Hobby Contact Information Address
United States of America
Horizon Service Center (Repairs and Repair Requests) servicecenter.horizonhobby.com/RequestForm/
2904 Research Rd.
Champaign, Illinois, 61822 USA
Horizon Product Support (Product Technical Assistance)
productsupport@horizonhobby.com
877-504-0233
Sales
websales@horizonhobby.com
800-338-4639
European Union
Horizon Technischer Service
service@horizonhobby.eu
+49 (0) 4121 2655 100
Hanskampring 9
D 22885 Barsbüttel, Germany
Sales: Horizon Hobby GmbH
WARRANTY AND SERVICE CONTACT INFORMATION
Law
These terms are governed by Illinois law (without regard to conflict of law principals). This
warranty gives you specific legal rights, and you may also have other rights which vary from state
to state. Horizon reserves the right to change or modify this warranty at any time without notice.
WARRANTY SERVICES
Questions, Assistance, and Services
Your local hobby store and/or place of purchase cannot provide warranty support or service.
Once assembly, setup or use of the Product has been started, you must contact your local
distributor or Horizon directly. This will enable Horizon to better answer your questions and
service you in the event that you may need any assistance. For questions or assistance, please
visit our website at www.horizonhobby.com, submit a Product Support Inquiry, or call the toll
free telephone number referenced in the Warranty and Service Contact Information section to
speak with a Product Support representative.
Inspection or Services
If this Product needs to be inspected or serviced and is compliant in the country you live
and use the Product in, please use the Horizon Online Service Request submission process
found on our website or call Horizon to obtain a Return Merchandise Authorization (RMA)
number. Pack the Product securely using a shipping carton. Please note that original boxes
may be included, but are not designed to withstand the rigors of shipping without additional
protection. Ship via a carrier that provides tracking and insurance for lost or damaged parcels,
as Horizon is not responsible for merchandise until it arrives and is accepted at our facility.
An Online Service Request is available at http://www.horizonhobby.com/content/service-
center_render-service-center. If you do not have internet access, please contact Horizon
Product Support to obtain a RMA number along with instructions for submitting your product
for service. When calling Horizon, you will be asked to provide your complete name, street
address, email address and phone number where you can be reached during business hours.
When sending product into Horizon, please include your RMA number, a list of the included
items, and a brief summary of the problem. A copy of your original sales receipt must be
included for warranty consideration. Be sure your name, address, and RMA number are clearly
written on the outside of the shipping carton.
NOTICE: Do not ship Li-Po batteries to Horizon. If you have any issue with a
Li-Po battery, please contact the appropriate Horizon Product Support office.
Warranty Requirements
For Warranty consideration, you must include your original sales receipt verifying
the proof-of-purchase date. Provided warranty conditions have been met, your Product
will be serviced or replaced free of charge. Service or replacement decisions are at the sole
discretion of Horizon.
Non-Warranty Service
Should your service not be covered by warranty, service will be completed and
payment will be required without notification or estimate of the expense unless
the expense exceeds 50% of the retail purchase cost. By submitting the item for
service you are agreeing to payment of the service without notification. Service estimates are
available upon request. You must include this request with your item submitted for service.
Non-warranty service estimates will be billed a minimum of ½ hour of labor. In addition you
will be billed for return freight. Horizon accepts money orders and cashier’s checks, as well as
Visa, MasterCard, American Express, and Discover cards. By submitting any item to Horizon for
service, you are agreeing to Horizon’s Terms and Conditions found on our website http://www.
horizonhobby.com/content/service-center_render-service-center.
ATTENTION: Horizon service is limited to Product compliant in the country of
use and ownership. If received, a non-compliant Product will not be serviced.
Further, the sender will be responsible for arranging return shipment of the un-
serviced Product, through a carrier of the sender’s choice and at the sender’s
expense. Horizon will hold non-compliant Product for a period of 60 days from
notification, after which it will be discarded.
10/15
FCC INFORMATION
FCC ID: CONTAINS BRWKATY1T | FCC ID: CONTAINS BRWSR6100AT
Supplier’s Declaration of Conformity
LOSI LASERNUT ULTRA 4 ROCK RACER, RTR: 1/10 4WD (LOS03028)
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
CAUTION: changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Horizon Hobby, LLC
2904 Research Rd.,
Champaign, IL 61822
Web: HorizonHobby.com
COMPLIANCE INFORMATION
FOR THE EUROPEAN UNION
IC INFORMATION
IC: CONTAINS 6157A-KATY1T | CONTAINS 6157A-SR6100AT
CAN ICES-3 (B)/NMB-3(B)
This device contains license-exempt transmitter(s)/receivers(s) that comply with Innovation,
Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to
the following 2 conditions:
This device may not cause interference.
This device must accept any interference, including interference that may cause undesired
operation of the device.
EU Compliance Statement:
LOSI LASERNUT ULTRA 4 ROCK RACER, RTR: 1/10 4WD (LOS03028)
Hereby, Horizon Hobby, LLC declares that the device is in compliance with the
following: EU Radio Equipment Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address:
https://www.horizonhobby.com/content/support-render-compliance.
Transmitter:
Frequency Band: 2402.0–2478.0 MHz
Max EIRP: 17.5 dBm
Receiver:
Frequency Band: 2402-2478 MHz
Max EIRP: 20 dBm
EU Manufacturer of Record:
Horizon Hobby, LLC
2904 Research Road
Champaign, IL 61822 USA
EU Importer of Record:
Horizon Hobby, GmbH
Hanskampring 9
22885 Barsbüttel Germany
WEEE NOTICE:
This appliance is labeled in accordance with European Directive 2012/19/EU
concerning waste of electrical and electronic equipment (WEEE). This label
indicates that this product should not be disposed of with household waste. It
should be deposited at an appropriate facility to enable recovery and recycling.
34
LOSI
®
TENACITY
®
LASERNUT ULTRA 4 1/10 4WD RTR ROCK RACER
REPLACEMENT PARTS // TEILELISTE // LISTE DES PIÈCES DE RECHANGE // ELENCO DEI RICAMBI
Part # English Deutsch Français Italiano
LOS230072 Body Clip Leash (4) Gehäuseklemme Schnur (4) Laisse de clip de carrosserie (4) Lacci per clip per carrozzeria (4)
LOS230075 Body Set, Blue, Painted Karosseriesatz, blau, lackiert Carrosserie, bleue, peinte Kit carrozzeria a vernice blu
LOS230076 Body Set, Red, Painted Karosseriesatz, rot, lackiert Carrosserie, rouge, peinte Kit carrozzeria a vernice rossa
LOS230077 Body Set, Clear Karosseriesatz, farblos Carrosserie, transparente Kit carrozzeria trasparente
LOS230078 Cage Set Käfigsatz Ensemble cage Kit scocca
LOS230079 LED, Cage Parts LED, Käfigteile LED, pièces de la cage Parti scocca, LED
LOS230080 Spare Tire Rack Ersatzreifenstange Support de pneu de secours Porta ruota di ricambio
LOS231026 Steering Bellcrank Set Steuerungsumlenkhebelsatz Ensemble leviers de renvoi de direction Kit squadrette di sterzo
LOS231027 Steering Posts, Tubes & Hardware Lenksäulen, Rohre und Hardware
Colonnes de direction, tubes et
accessoires
Supporti, tubi e bulloneria dello sterzo
LOS231030 Chassis Support Set Karosserieträgersatz Ensemble support de châssis Kit supporti telaio
LOS231031 Motor Mount Motorhalterung Support moteur Supporto motore
LOS231033 Steering Drag Link & Hardware Lenkzwischenstange & Hardware
Barre d’accouplement de la direction &
accessoires
Tirante di sterzo e bulloneria
LOS231057 Rod Ends & Links Stangenende und Verbindungen Embouts de bielle et liaisons Teste a snodo e aste
LOS231062 Aluminum Chassis Aluminiumchassis Châssis en aluminium Telaio in alluminio
LOS231063 Side Guards Seitenschutze Protections latérales Protezioni laterali
LOS231064 Top Deck, Battery Mount Oberdeck, Akkuhalterung Pont supérieur, support de batterie Piano superiore, supporto batteria
LOS231065 Grid Set Halterungssatz Ensemble grille Kit griglia
LOS232023 Diff Case Set Differentialgehäusesatz Ensemble boîtier de différentiel Kit scatola diff.
LOS232024 Center Drive Coupler Zentrale Antriebskupplung Coupleur d’entraînement central Attacco albero trasmissione
LOS232025 40T Spur Gear, Mod 1 40T-Stirnrad, Mod 1 Engrenage cylindrique 40 dents, Mod 1 Corona 40T, Mod 1
LOS232026 Diff Housing Diffentialgehäuse Logement du différentiel Carter differenziale
LOS232027 Front Ring & Pinion Gear Set Vorderer Ring- und Zahnradgetriebesatz
Ensemble anneau et engrenage à
pignons avant
Kit pignone e corona anteriori
LOS232028 Rear Ring & Pinion Gear Set Hinterer Ring- und Zahnradgetriebesatz
Ensemble anneau et engrenage à
pignons arrière
Kit pignone e corona posteriori
LOS232029 Diff Gear Set w/Hardware Differentialgetriebesatz mit Hardware
Ensemble engrenage de différentiel avec
accessoires
Kit ingr. diff. con bulloneria
LOS232030 Outdrive, Diff (2) Flexwelle, Diff (2) Entraînement extérieur, différentiel (2) Outdrive, diff.(2)
LOS232031 Wheel Hex Set (4) Sechskantradsatz (4) Ensemble écrous hexagonaux de roue (4) Kit esagoni ruote (4)
LOS232032 Front/Rear Driveshafts (2) Front/Heck Antriebswellen (2) Arbres de transmission avant/arrière (2) Alberi trasmissione ant./post. (2)
LOS232033 Front Center Dogbone (1) Vorderes mittiges Dogbone (1) Dogbone central avant (1) Cardano centrale ant. (1)
LOS232034 Rear Center Dogbone (1) Hinteres mittiges Dogbone (1) Dogbone central arrière (1) Cardano centrale post. (1)
LOS232054 Center Dogbone Set Mittiger Dogbone-Satz Ensemble dogbone central Kit cardano centrale
LOS232055 Aluminum Diff Case Aluminium-Differentialgehäuse Ensemble différentiel en aluminium Scatola diff. in alluminio
LOS233011 Shock Plastics Set Kunststoff-Stoßdämpfersatz Ensemble plastiques d’amortisseur Kit plastiche ammortizzatori
LOS233013 Spring Set Federnsatz Ensemble ressort Kit molle
LOS233014 Rear Shock Shaft (2) Hintere Kolbenstange (2) Arbre d’amortisseur arrière (2) Albero amm. post. (2)
LOS233015 Front Shock Shaft (2) Vordere Kolbenstange (2) Arbre d’amortisseur avant (2) Albero amm. ant. (2)
LOS233025 Adjuster Nut Einstellmutter Écrou de réglage Dado di registrazione
LOS233026 Aluminum Shock Caps Aluminium Stoßdämpferkappen Capuchons d’amortisseur en aluminium Tappi amm. in alluminio
LOS233027 Aluminum Front Shock Bodies Vordere Stoßdämpfergehäuse, Aluminium Corps d’amortisseur avant en aluminium Carcasse amm. in alluminio ant.
LOS233028 Aluminum Rear Shock Bodies Hintere Stoßdämpfergehäuse, Aluminium Corps d’amortisseur arrière en aluminium Carcasse amm. in alluminio post.
LOS234016 Front Arm Set Vorderarmsatz Ensemble bras avant Kit braccio anteriore
LOS234017 Rear Arm Set Hinterarmsatz Ensemble bras arrière Kit braccio posteriore
LOS234018 Front Spindle & Carrier Set Front-Spindel- & Trägersatz Ensemble axe et support avant Kit fuselli e portafuselli ant.
LOS234019 Front/Rear Pin Mount Cover Set
Vorderer/Hinterer Stift
Halterungsabdeckungssatz
Ensemble cache de support axe FR/R Kit protezione montanti perni ant/post.
LOS234020 Rear Hub Set Hinterradnabensatz Ensemble moyeu arrière Kit mozzi posteriori
LOS234021 Hingepin & Kingpin Set Scharnierstift & Sattelzapfensatz
Ensemble axe de charnière et axe de
pivot
Kit perni e cardini
LOS234023 Pivot Pin Mount Set, Steel (4) Drehzapfensatz, Stahl (4) Ensemble support axe de pivot, acier (4) Kit supporto perno girevole, acciaio (4)
LOS234035 Aluminum Front Shock Tow Vordere Aluminium-Stoßdämpferbrücke Tour d’amortisseur avant en aluminium Torre amm. in alluminio, ant.
LOS234036 Aluminum Rear Shock Tow Hintere Aluminium-Stoßdämpferbrücke Tour d’amortisseur arrière en aluminium Torre amm. in alluminio, post.
LOS234037 Sway Bar Set Schwingen-Set Ensemble barre stabilisatrice Kit barra antirollio
LOS234038 Rear Sway Bar Set Heck Schwingen-Satz Ensemble barre stabilisatrice arrière Kit barra antirollio posteriore
LOS235011 Set Screw, M3 x 3mm Cup Point (10) Stellschraube M3 x 3 mm Ringschneide (10) Vis de fixation M3 x 3 mm Bout cuvette (10) Kit viti, M3 x 3 mm, senza testa (10)
LOS235012 Set Screw, M4 x 4mm Cup Point (10) Stellschraube M4 x 4 mm Ringschneide (10) Vis de fixation M4 x 4 mm Bout cuvette (10) Kit viti, M4 x 4 mm, senza testa (10)
LOS235024 Button Head Screw, M3 x 25mm (10) Rundkopfschraube, M3 x 25mm (10) Vis à tête bombée M3 x 25 mm (10) Viti a testa tonda, M3 x 25 mm (10)
LOS235025 Button Head Screw, M3 x 30mm (10) Rundkopfschraube, M3 x 30mm (10) Vis à tête bombée M3 x 30 mm (10) Viti a testa tonda, M3 x 30 mm (10)
LOS235026 Set Screw, M3 x 4mm Cup Point (10) Stellschraube M3 x 4mm Ringschneide (10) Vis de fixation M3 x 4mm Bout cuvette (10) Kit viti, M3 x 4 mm, senza testa (10)
LOS235027 Set Screw, M3 x 10mm Cup Point (10)
Stellschraube M3 x 10mm
Ringschneide (10)
Vis de fixation M3 x 10mm Bout
cuvette (10)
Kit viti, M3 x 10 mm, senza testa (10)
35
LOSI
®
TENACITY
®
LASERNUT ULTRA 4 1/10 4WD RTR ROCK RACER
REPLACEMENT PARTS // TEILELISTE // LISTE DES PIÈCES DE RECHANGE // ELENCO DEI RICAMBI
Part # English Deutsch Français Italiano
LOS236000 E-Clips 2.5mm (12) E-Klemmen, 2,5 mm (12) Attaches en E 2,5 mm (12) E-Clip 2,5 mm (12)
LOS236001 3.2 x 7 x .5mm Washer (10) 3,2 x 7 x 5mm Unterlegscheibe (10) Rondelle 3,2 × 7 × 0,5 mm (10) Rondelle 3,2 x 7 x 0,5 mm (10)
LOS237000 12 x 18 x 4mm Ball Bearing (4) 12 x 18 x 4mm, Kugellager (4) Roulement à billes 12 x 18 x 4 mm (4) Cuscinetto a sfera 12 x 18 x 4 mm (4)
LOS237001 10 x 15 x 4mm Ball Bearing (4) 10 x 15 x 4mm, Kugellager (4) Roulement à billes 10 x 15 x 4 mm (4) Cuscinetto a sfera 10 x 15 x 4 mm (4)
LOS237002 5 x 11 x 4mm Ball Bearing (4) 5 x 11 x 4mm, Kugellager (4) Roulement à billes 5 x 11 x 4 mm (4) Cuscinetto a sfera 5 x 11 x 4 mm (4)
LOS43028 Wheel w/BFG Tire, Copper Rad mit BFG-Reifen, Kupfer Roue avec pneu BFG, cuivre Ruota con pneumatico BFG, rame
LOSA3572 1.0 Module Pitch Pinion, 12T 1.0 Modul Getrieberad, 12T Module de pignon de pas 1.0, 12 dents Pignone Modulo 1.0, 12T
LOSA3574 1.0 Module Pitch Pinion, 14T 1.0 Modul Getrieberad, 14T Module de pignon de pas 1.0, 14 dents Pignone Modulo 1.0, 14T
LOSA6940 6 x 12mm Sealed Ball Bearing (4) 6 x 12mm abgedichtetes Kugellager (4)
Roulement à billes hermétique 6 x 12
mm (4)
Cuscinetti a sfera sigillati 6 x 12 mm (4)
SPM2340
DX3 SMART DSMR 3CH Transmitter
w/SR315
DX3 SMART DSMR-Sender mit 3 Kanälen
mit SR315
Émetteur DX3 SMART DSMR 3 canaux
avec SR315
Trasmittente DX3 SMART DSMR 3 CH
con SR315
SPMS614 S614 Metal Gear Servo, 23T WP S614 Metallgetriebeservo 23T WP
Servo à engrenages métalliques S614,
23 dents, étanche
Servo ingr. in metallo S614 23T WP
SPMSR6100AT
SR6100AT DSMR 6CH AVC
Telemetry Surface Receiver
SR6100AT DSMR AVC Telemetrie
Oberflächenempfänger mit 6 Kanälen
Récepteur de surface de télémétrie
AVC 6 canaux SR6100AT DSMR
Ricevitore di superficie con telemetria
SR6100AT DSMR 6CH AVC
SPMXSE1130 Firma 130A Brushless Smart ESC
Firma 130 A Bürstenloser Smart-
Geschwindigkeitsregler
Variateur ESC sans balais 130 A Smart
Firma
Smart ESC Firma 130 A Brushless
SPMXSM2200 3668-1900Kv Motor 3668 - 1900Kv Motor Moteur 3668 - 1900Kv Motore 3668 - 1900Kv
TLR5280 Silicone Differential Fluid, 5,000CS Differential-Silikonflüssigkeit, 5.000CS Liquide silicone pour différentiel, 5 000 CS Fluido siliconico per differenziale, 5.000 CS
TLR5282 Silicone Differential Fluid, 10,000CS Differential-Silikonflüssigkeit, 10.000CS Liquide silicone pour différentiel, 10 000 CS Fluido siliconico per differenziale, 10.000 CS
TLR5284 Silicone Differential Fluid, 20,000CS Differential-Silikonflüssigkeit, 20.000CS Liquide silicone pour différentiel, 20 000 CS Fluido siliconico per differenziale, 20.000 CS
TLR5901 Button Head Screw, M3 x 6mm (10) Rundkopfschraube, M3 x 6mm (10) Vis à tête bombée M3 x 6mm (10) Viti a testa tonda, M3 x 6 mm (10)
TLR5902 Button Head Screw, M3 x 8mm (10) Rundkopfschraube, M3 x 8mm (10) Vis à tête bombée M3 x 8mm (10) Viti a testa tonda, M3 x 8 mm (10)
TLR5903 Button Head Screw, M3 x 10mm (10) Rundkopfschraube, M3 x 10mm (10) Vis à tête bombée M3 x 10mm (10) Viti a testa tonda, M3 x 10 mm (10)
TLR5904 Button Head Screw, M3 x 12mm (10) Rundkopfschraube, M3 x 12mm (10) Vis à tête bombée M3 x 12mm (10) Viti a testa tonda, M3 x 12 mm (10)
TLR5905 Button Head Screw, M3 x 18mm (10) Rundkopfschraube, M3 x 18mm (10) Vis à tête bombée M3 x 18mm (10) Viti a testa tonda, M3 x 18 mm (10)
TLR5908 Button Head Screw, M3 x 44mm (4) Rundkopfschraube, M3 x 44mm (4) Vis à tête bombée M3 x 44mm (4) Viti a testa tonda, M3 x 44 mm (4)
TLR5909 Button Head Screw, M3 x 16mm (10) Rundkopfschraube, M3 x 16mm (10) Vis à tête bombée M3 x 16mm (10) Viti a testa tonda, M3 x 16 mm (10)
TLR5910 Button Head Screw, M3 x 14mm (10) Rundkopfschraube, M3 x 14mm (10) Vis à tête bombée M3 x 14mm (10) Viti a testa tonda, M3 x 14 mm (10)
TLR5911 Button Head Screw, M3 x 20mm (10) Rundkopfschraube, M3 x 20mm (10) Vis à tête bombée M3 x 20mm (10) Viti a testa tonda, M3 x 20 mm (10)
TLR5914 Button Head Screw, M2 x 12mm (10) Rundkopfschraube, M2 x 12mm (10) Vis à tête bombée, M2 x 12mm (10) Viti a testa tonda, M2 x 12 mm (10)
TLR5932 Cap Head Screw, M3 x 10mm (10) Inbusschraube, M3 x 10mm (10)
Vis d’assemblage creuse,
M3 x 10mm (10)
Viti a testa cilindrica, M3 x 10 mm (10)
TLR5933 Cap Head Screw, M3 x 12mm (10) Inbusschraube, M3 x 12mm (10)
Vis d’assemblage creuse, M3 x 12mm
(10)
Viti a testa cilindrica, M3 x 12 mm (10)
TLR5962 Flathead Screw, M3 x 10mm (10) Flachkopfschraube, M3 x 10mm (10) Vis à tête plate, M3 x 10mm (10) Viti a testa piana, M3 x 10 mm (10)
TLR5963 Flathead Screw, M3 x 12mm (10) Flachkopfschraube, M3 x 12mm (10) Vis à tête plate, M3 x 12mm (10) Viti a testa piana, M3 x 12 mm (10)
TLR5964 Flathead Screw, M3 x 16mm (10) Flachkopfschraube, M3 x 16mm (10) Vis à tête plate, M3 x 16mm (10) Viti a testa piana, M3 x 16 mm (10)
TLR5965 Flathead Screw, M3 x 20mm (10) Flachkopfschraube, M3 x 20mm (10) Vis à tête plate, M3 x 20mm (10) Viti a testa piana, M3 x 20 mm (10)
TLR6313 Locknut, M3 x .5 x 5.5mm (10) Kontermutter, M3 x 0,5 x 5,5 mm (10) Contre-écrou M3 x 5 x 5,5 mm (10) Controdadi, M3 x 0,5 x 5,5 mm (10)
TLR6352 Washers, M3 (10) Unterlegscheiben, M3 (10) Rondelles, M3 (10) Rondelle, M3 (10)
TLR8202 Body Clips, Black (12) Gehäuseklemmen, schwarz (12) Clips de carrosserie, noir (12) Clip carrozzeria, colore nero (12)
TLR74008 Silicone Shock Oil, 35 wt, 2 oz Stoßdämpfer-Silikonöl, 35 wt, 59 ml (2 oz)
Huile silicone pour amortisseurs, 35 wt,
59 mL
Olio di silicone per ammortizzatori,
35 wt, 60 ml (2 oz)
TLR235007 Flat Head Screw, M2.5 x 10mm (10) Flachkopfschraube M2,5 x 10mm (10) Vis à tête plate M2,5 x 10 mm (10) Smart ESC Firma 130 A Brushless
TLR255008 Button Head Screw, M4 x 16mm (10) Rundkopfschraube, M4 x 16mm (10) Vis à tête bombée, M4 x 16 mm (10) Viti a testa tonda, M4 x 16 mm (10)
TLR255013 Flat Head Screws, M4 x 12mm (10) Rundkopfschrauben, M4 x 12mm (10) Vis à tête plate, M4 x 12mm (10) Viti a testa piana, M4 x 12 mm (10)
TLR256005 Nylock Nut, M4 (10) Nylock-Mutter, M4 (10) Contre-écrou Nylock, M4 (10) Dado Nylock, M4 (10)
TLR336005
M3 Flanged Aluminum Locknut,
Black (10)
M3 Aluminium-Kontermutter mit Flansch,
schwarz (10)
Contre-écrou M3 en aluminium à collet,
noir (10)
Controdado allumino flangiato M3,
nero (10)
36
LOSI
®
TENACITY
®
LASERNUT ULTRA 4 1/10 4WD RTR ROCK RACER
OPTIONAL PARTS // OPTIONALE TEILE // PIÈCES OPTIONNELLES // PARTI OPZIONALI
Part # English Deutsch Français Italiano
DYN2834 Startup Tool Set: Metric Anfänger-Werkzeugsatz: Metrisch Jeu d’outils de démarrage : Métrique Kit completo attrezzi base: metrico
DYN5500 Magnum Force 2 Motor Spray, 13 oz Magnum Force 2 Motorspray, 368 g
Vaporisateur pour moteur Magnum Force
2, 368 g
Spray per motore Magnum Force 2,
385 ml (13 oz)
DYNT2010 Machined Nut Driver Set (4) Metric Set gefräste Steckschlüssel (4) metrisch
Ensemble tourne-écrou usiné (4)
Métrique
Kit di chiavi (4) metriche
DYNT2030 Machined Hex Driver Set (4) Met
Set gefräste Inbusschraubendreher
(4) Met
Ensemble clé à six pans usinée (4)
Métrique
Kit di chiavi a brugola (4) metriche
LOS331012 Mach Alum Motor Mount Gefräste Motorhalterung, Aluminium Support moteur en aluminium usiné Supporto motore in alluminio lavorato
LOS334011 Aluminum Rear Hubs (2) Hintere Naben, Aluminium (2) Moyeux arrière en aluminium (2) Mozzi in alluminio, post. (2)
LOS334012 Aluminum Front Spindle (2) Front-Spindel, Aluminium (2) Axe avant en aluminium (2) Fuselli in alluminio, ant. (2)
LOS334013 Aluminum Spindle Carrier (2) Spindelträger, Aluminium (2) Support d’axe en aluminium (2) Portafuselli in alluminio (2)
LOS43011 Desert Claws Tires w/Foam, Soft (2)
Desert Claws-Reifen mit Schaumstoff
(2)
Pneus Desert Claws avec mousse,
douce (2)
Pneumatici Desert Claw con schiuma,
morbidi (2)
LOSA3571 1.0 Module Pitch Pinion,11T 1.0 Modul Getrieberad, 11T Module de pignon de pas 1.0, 11 dents Pignone Modulo 1.0, 11T
LOSA3573 1.0 Module Pitch Pinion, 13T 1.0 Modul Getrieberad, 13T Module de pignon de pas 1.0, 13 dents Pignone Modulo 1.0, 13T
LOSA3576 1.0 Module Pitch Pinion, 16T 1.0 Modul Getrieberad, 16T Module de pignon de pas 1.0, 16 dents Pignone Modulo 1.0, 16T
LOSA3578 1.0 Module Pitch Pinion, 18T 1.0 Modul Getrieberad, 18T Module de pignon de pas 1.0, 18 dents Pignone Modulo 1.0, 18T
LOSA99173 Ride Height Gauge Höhenmesser Jauge de hauteur de course Misuratore altezza di marcia
LOSA99174 Car Stand Fahrzeugständer Socle Supporto automodello
LOSB3493 Aluminum Clamping Wheel Hex Aluminium Klemmrad Sechskant
Roue de serrage hexagonale en
aluminium
Rotella di bloccaggio esagonale in
alluminio
SPM6730 Spektrum Tx Storage Bag* Spektrum Tx Aufbewahrungstasche* Sac de rangement Spektrum Tx* Sacco custodia Tx Spektrum
SPMSS6230 S6230 U-T / M-S Digital WP Servo S6230 U-T/M-S Digitaler WP Servo Servo numérique S6230 U-T / M-S WP
Servo impermeabile digitale S6230
U-T/M-S
TLR332014 Rear Hex, +0.5mm Width, Aluminum
Hinterer Sechskant, +0,5 mm Breite,
Aluminium
Écrou hexagonal arrière, +0,5 mm
de largeur, aluminium
Esagono posteriore, larghezza +0,5 mm,
alluminio
TLR336000
4mm Aluminum Serrated Lock Nut,
Black (6)
4 mm Aluminium Rändelmutter,
schwarz (6)
Contre-écrou en aluminium à embase
striée 4 mm, noir (6)
Controdado dentato in alluminio 4 mm,
nero (6)
TLR336001
4mm Aluminum Serrated Lock Nut,
Blue (6)
4 mm Aluminium Rändelmutter,
blau (6)
Contre-écrou en aluminium à embase
striée 4 mm, bleu (6)
Controdado dentato in alluminio 4 mm,
blu (6)
TLR5062 Bleeder Shock Cap, Aluminum (2)
Stoßdämpfer-Entlüfterkappe,
Aluminium (2)
Contre-écrou en aluminium à embase
striée 4 mm, bleu (6)
Tappi di sfiato per ammortizzatori,
alluminio (2)
TLR74006 Silicone Shock Oil, 30 wt, 2 oz
Stoßdämpfer-Silikonöl, 30 wt, 59 ml
(2 oz)
Huile silicone pour amortisseurs, 30 WT,
59 mL
Olio di silicone per ammortizzatori, 30
wt, 60 ml (2 oz)
TLR74010 Silicone Shock Oil, 40 wt, 2 oz
Stoßdämpfer-Silikonöl, 40 wt, 59 ml
(2 oz)
Huile silicone pour amortisseurs, 40 WT,
59 mL
Olio di silicone per ammortizzatori, 40
wt, 60 ml (2 oz)
TLR76000 Tire Glue, Standard Reifenklebemittel, Standard Colle de pneu, standard Colla pneumatici, standard
TLR76004 TLR Lok, Threadlock, Blue TLR Lok, Schraubensicherung, blau Verrou TLR, frein-filet, bleu TLR Lok, frenafiletti, blu
Part # English Deutsch Français Italiano
DYNC2005CA Prophet Sport LiPo 35W AC Charger Prophet Sport LiPo 35 W AC-Ladegerät Chargeur CA Li-Po 35 W Prophet Sport
Caricabatterie Prophet Sport LiPo
35 W CA
SPMXC1080 Spektrum Smart S100 AC Charger
Spectrum Smart S100 Wechselstrom-
Ladegerät
Chargeur CA Spektrum Smart S100
Caricabatterie Spektrum Smart
S100 CA
SPMX50003S50H5
11.1V 5000mAh 3S 50C Smart
Hardcase LiPo Battery: IC5
11,1 V 5000 mAh 3S 50C Smart
LiPo-Akku, Hartschale: IC5
Batterie LiPo Smart 11,1 V 5 000 mAh
3S 50C, boîtier rigide : IC5
Batteria Li-Po 11,1 V 5000 mAh 3S
50C Smart Hardcase: IC5
SPMX50004S50H5
14.8V 5000mAh 4S 50C Smart
Hardcase LiPo Battery: IC5
14,8 V 5000 mAh 4S 50C Smart LiPo-
Akku, Hartschale: IC5
Batterie LiPo Smart 14,8V 5 000 mAh
4S 50C, boîtier rigide : IC5
Batteria Li-Po 14,8 V 5000 mAh 4S
50C Smart Hardcase: IC5
RECOMMENDED PARTS // EMPFOHLENE TEILE// PIÈCES RECOMMANDÉES // PARTI CONSIGLIATE
37
LOSI
®
TENACITY
®
LASERNUT ULTRA 4 1/10 4WD RTR ROCK RACER
EXPLODED VIEW // EXPLOSIONSZEICHNUNG // VUE ÉCLATÉE DES PIÈCES // VISTA ESPLOSA DELLE PARTI
SPMXSM2200
LOS231064
SPMXSE1130
LOS231054
LOS231062
LOS231063
LOS231063
LOS231064
LOS232029
LOS232025
TLR235007
LOS237000
TLR3100
LOS232030
LOS232054
LOS232023
LOS232030
LOS237000
TLR5901
LOS232055
LOS232026
LOSA3572 (12T)
LOSA3574 (14T)
LOS235024
TLR5905
LOS233014
LOS233015
TLR6313
LOS233011
LOS233013
LOS231030
TLR336005
LOSB2906
LOS233027
LOS233025
LOS233026
LOS233028
LOS236000
LOS235012
TLR6352
TLR235007
LOS234022
LOS234035
LOS234037
LOS234021
LOS234023
LOS234019
TLR5909
TLR5911
TLR5964
LOS234016
LOS234018
LOS237001
LOS234021
LOS234018
LOS232032
LOS232032
TLR5911
LOS231057
TLR6313
TLR5964
LOS231057
TLR6313
TLR5905
LOS235026
LOSA6940
LOS232031
LOS234016
TLR255008
LOS232030
LOS232030
LOS237000
LOS237000
LOS232023
LOS232028
LOS237002
LOS237002
LOS232024
LOS232023
LOS232026
LOS232026
LOS237000
LOS232030
LOS232029
LOS232026
LOS232023
TLR5965
LOS232023
LOS237000
LOS232027
LOS232023
TLR5933
LOS232030
LOS231027
LOS231027
LOS231026
TLR5904
TLR6313
TLR5904
TLR5910
LOS231057
LOS231024
LOS231057
LOS231054
LOS231026
LOS231033
LOS232026
TLR5963
TLR5964
TLR5932
LOS232054
LOS231031
SPMS614
SPMSR6100AT
TLR5904
LOS232029
LOS232023
TLR5904 TLR5964
LOS232027
LOS237002
LOS237002
LOS232024
TLR5911
TLR5911
TLR5905
LOS232031
TLR336000
TLR256005
LOS237001
LOSA6940
LOS234021
LOS234023
TLR255013
TLR5963
LOS234020
LOS234021
TLR6313
TLR6313
TLR6313
LOS234017
LOS234019
LOS234036
TLR235007
TLR5903
TLR5903
TLR5963
TLR5963
LOS235011
LOS231054t
LOS235025
TLR6313
TLR5908
LOS230079
TLR5904
LOS230079
LOS230078
LOS230078
LOS230078
LOS230079
LOS230079
LOS230079
LOS230079
LOS230079
LOS230080
LOS234038
LOS234038
LOS43028
LOS235025
LOS235025
TLR5903
TLR5903
TLR5903
TLR5903
TLR5903
TLR5901
TLR5901
TLR5901
TLR5903
TLR5903
TLR5903
TLR5901
LOS234038
TLR5901
TLR5903
TLR5901
TLR5903
LOS231065
LOS231065
LOS231065
TLR5901
TLR5901
LOS231065
TLR5901
TLR5901
LOS230076
LOS230077
LOS230079
TLR5901
TLR5903
TLR5962
TLR5962
TLR5963
TLR5903
SPMXSM2200
LOS231064
LOS230079
LOS230079
10K
FLUID
38
LOSI
®
TENACITY
®
LASERNUT ULTRA 4 1/10 4WD RTR ROCK RACER
EXPLODED VIEW // EXPLOSIONSZEICHNUNG // VUE ÉCLATÉE DES PIÈCES // VISTA ESPLOSA DELLE PARTI
SPMXSM2200
LOS231064
SPMXSE1130
LOS231054
LOS231062
LOS231063
LOS231063
LOS231064
LOS232029
LOS232025
TLR235007
LOS237000
TLR3100
LOS232030
LOS232054
LOS232023
LOS232030
LOS237000
TLR5901
LOS232055
LOS232026
LOSA3572 (12T)
LOSA3574 (14T)
LOS235024
TLR5905
LOS233014
LOS233015
TLR6313
LOS233011
LOS233013
LOS231030
TLR336005
LOSB2906
LOS233027
LOS233025
LOS233026
LOS233028
LOS236000
LOS235012
TLR6352
TLR235007
LOS234022
LOS234035
LOS234037
LOS234021
LOS234023
LOS234019
TLR5909
TLR5911
TLR5964
LOS234016
LOS234018
LOS237001
LOS234021
LOS234018
LOS232032
LOS232032
TLR5911
LOS231057
TLR6313
TLR5964
LOS231057
TLR6313
TLR5905
LOS235026
LOSA6940
LOS232031
LOS234016
TLR255008
LOS232030
LOS232030
LOS237000
LOS237000
LOS232023
LOS232028
LOS237002
LOS237002
LOS232024
LOS232023
LOS232026
LOS232026
LOS237000
LOS232030
LOS232029
LOS232026
LOS232023
TLR5965
LOS232023
LOS237000
LOS232027
LOS232023
TLR5933
LOS232030
LOS231027
LOS231027
LOS231026
TLR5904
TLR6313
TLR5904
TLR5910
LOS231057
LOS231024
LOS231057
LOS231054
LOS231026
LOS231033
LOS232026
TLR5963
TLR5964
TLR5932
LOS232054
LOS231031
SPMS614
SPMSR6100AT
TLR5904
LOS232029
LOS232023
TLR5904 TLR5964
LOS232027
LOS237002
LOS237002
LOS232024
TLR5911
TLR5911
TLR5905
LOS232031
TLR336000
TLR256005
LOS237001
LOSA6940
LOS234021
LOS234023
TLR255013
TLR5963
LOS234020
LOS234021
TLR6313
TLR6313
TLR6313
LOS234017
LOS234019
LOS234036
TLR235007
TLR5903
TLR5903
TLR5963
TLR5963
LOS235011
LOS231054t
LOS235025
TLR6313
TLR5908
LOS230079
TLR5904
LOS230079
LOS230078
LOS230078
LOS230078
LOS230079
LOS230079
LOS230079
LOS230079
LOS230079
LOS230080
LOS234038
LOS234038
LOS43028
LOS235025
LOS235025
TLR5903
TLR5903
TLR5903
TLR5903
TLR5903
TLR5901
TLR5901
TLR5901
TLR5903
TLR5903
TLR5903
TLR5901
LOS234038
TLR5901
TLR5903
TLR5901
TLR5903
LOS231065
LOS231065
LOS231065
TLR5901
TLR5901
LOS231065
TLR5901
TLR5901
LOS230076
LOS230077
LOS230079
TLR5901
TLR5903
TLR5962
TLR5962
TLR5963
TLR5903
SPMXSM2200
LOS231064
LOS230079
LOS230079
5K
FLUID
39
LOSI
®
TENACITY
®
LASERNUT ULTRA 4 1/10 4WD RTR ROCK RACER
EXPLODED VIEW // EXPLOSIONSZEICHNUNG // VUE ÉCLATÉE DES PIÈCES // VISTA ESPLOSA DELLE PARTI
SPMXSM2200
LOS231064
SPMXSE1130
LOS231054
LOS231062
LOS231063
LOS231063
LOS231064
LOS232029
LOS232025
TLR235007
LOS237000
TLR3100
LOS232030
LOS232054
LOS232023
LOS232030
LOS237000
TLR5901
LOS232055
LOS232026
LOSA3572 (12T)
LOSA3574 (14T)
LOS235024
TLR5905
LOS233014
LOS233015
TLR6313
LOS233011
LOS233013
LOS231030
TLR336005
LOSB2906
LOS233027
LOS233025
LOS233026
LOS233028
LOS236000
LOS235012
TLR6352
TLR235007
LOS234022
LOS234035
LOS234037
LOS234021
LOS234023
LOS234019
TLR5909
TLR5911
TLR5964
LOS234016
LOS234018
LOS237001
LOS234021
LOS234018
LOS232032
LOS232032
TLR5911
LOS231057
TLR6313
TLR5964
LOS231057
TLR6313
TLR5905
LOS235026
LOSA6940
LOS232031
LOS234016
TLR255008
LOS232030
LOS232030
LOS237000
LOS237000
LOS232023
LOS232028
LOS237002
LOS237002
LOS232024
LOS232023
LOS232026
LOS232026
LOS237000
LOS232030
LOS232029
LOS232026
LOS232023
TLR5965
LOS232023
LOS237000
LOS232027
LOS232023
TLR5933
LOS232030
LOS231027
LOS231027
LOS231026
TLR5904
TLR6313
TLR5904
TLR5910
LOS231057
LOS231024
LOS231057
LOS231054
LOS231026
LOS231033
LOS232026
TLR5963
TLR5964
TLR5932
LOS232054
LOS231031
SPMS614
SPMSR6100AT
TLR5904
LOS232029
LOS232023
TLR5904 TLR5964
LOS232027
LOS237002
LOS237002
LOS232024
TLR5911
TLR5911
TLR5905
LOS232031
TLR336000
TLR256005
LOS237001
LOSA6940
LOS234021
LOS234023
TLR255013
TLR5963
LOS234020
LOS234021
TLR6313
TLR6313
TLR6313
LOS234017
LOS234019
LOS234036
TLR235007
TLR5903
TLR5903
TLR5963
TLR5963
LOS235011
LOS231054t
LOS235025
TLR6313
TLR5908
LOS230079
TLR5904
LOS230079
LOS230078
LOS230078
LOS230078
LOS230079
LOS230079
LOS230079
LOS230079
LOS230079
LOS230080
LOS234038
LOS234038
LOS43028
LOS235025
LOS235025
TLR5903
TLR5903
TLR5903
TLR5903
TLR5903
TLR5901
TLR5901
TLR5901
TLR5903
TLR5903
TLR5903
TLR5901
LOS234038
TLR5901
TLR5903
TLR5901
TLR5903
LOS231065
LOS231065
LOS231065
TLR5901
TLR5901
LOS231065
TLR5901
TLR5901
LOS230076
LOS230077
LOS230079
TLR5901
TLR5903
TLR5962
TLR5962
TLR5963
TLR5903
SPMXSM2200
LOS231064
LOS230079
LOS230079
35 WT
OIL
40
LOSI
®
TENACITY
®
LASERNUT ULTRA 4 1/10 4WD RTR ROCK RACER
EXPLODED VIEW // EXPLOSIONSZEICHNUNG // VUE ÉCLATÉE DES PIÈCES // VISTA ESPLOSA DELLE PARTI
SPMXSM2200
LOS231064
SPMXSE1130
LOS231054
LOS231062
LOS231063
LOS231063
LOS231064
LOS232029
LOS232025
TLR235007
LOS237000
TLR3100
LOS232030
LOS232054
LOS232023
LOS232030
LOS237000
TLR5901
LOS232055
LOS232026
LOSA3572 (12T)
LOSA3574 (14T)
LOS235024
TLR5905
LOS233014
LOS233015
TLR6313
LOS233011
LOS233013
LOS231030
TLR336005
LOSB2906
LOS233027
LOS233025
LOS233026
LOS233028
LOS236000
LOS235012
TLR6352
TLR235007
LOS234022
LOS234035
LOS234037
LOS234021
LOS234023
LOS234019
TLR5909
TLR5911
TLR5964
LOS234016
LOS234018
LOS237001
LOS234021
LOS234018
LOS232032
LOS232032
TLR5911
LOS231057
TLR6313
TLR5964
LOS231057
TLR6313
TLR5905
LOS235026
LOSA6940
LOS232031
LOS234016
TLR255008
LOS232030
LOS232030
LOS237000
LOS237000
LOS232023
LOS232028
LOS237002
LOS237002
LOS232024
LOS232023
LOS232026
LOS232026
LOS237000
LOS232030
LOS232029
LOS232026
LOS232023
TLR5965
LOS232023
LOS237000
LOS232027
LOS232023
TLR5933
LOS232030
LOS231027
LOS231027
LOS231026
TLR5904
TLR6313
TLR5904
TLR5910
LOS231057
LOS231024
LOS231057
LOS231054
LOS231026
LOS231033
LOS232026
TLR5963
TLR5964
TLR5932
LOS232054
LOS231031
SPMS614
SPMSR6100AT
TLR5904
LOS232029
LOS232023
TLR5904 TLR5964
LOS232027
LOS237002
LOS237002
LOS232024
TLR5911
TLR5911
TLR5905
LOS232031
TLR336000
TLR256005
LOS237001
LOSA6940
LOS234021
LOS234023
TLR255013
TLR5963
LOS234020
LOS234021
TLR6313
TLR6313
TLR6313
LOS234017
LOS234019
LOS234036
TLR235007
TLR5903
TLR5903
TLR5963
TLR5963
LOS235011
LOS231054t
LOS235025
TLR6313
TLR5908
LOS230079
TLR5904
LOS230079
LOS230078
LOS230078
LOS230078
LOS230079
LOS230079
LOS230079
LOS230079
LOS230079
LOS230080
LOS234038
LOS234038
LOS43028
LOS235025
LOS235025
TLR5903
TLR5903
TLR5903
TLR5903
TLR5903
TLR5901
TLR5901
TLR5901
TLR5903
TLR5903
TLR5903
TLR5901
LOS234038
TLR5901
TLR5903
TLR5901
TLR5903
LOS231065
LOS231065
LOS231065
TLR5901
TLR5901
LOS231065
TLR5901
TLR5901
LOS230076
LOS230077
LOS230079
TLR5901
TLR5903
TLR5962
TLR5962
TLR5963
TLR5903
SPMXSM2200
LOS231064
LOS230079
LOS230079
20K
FLUID
41
LOSI
®
TENACITY
®
LASERNUT ULTRA 4 1/10 4WD RTR ROCK RACER
EXPLODED VIEW // EXPLOSIONSZEICHNUNG // VUE ÉCLATÉE DES PIÈCES // VISTA ESPLOSA DELLE PARTI
SPMXSM2200
LOS231064
SPMXSE1130
LOS231054
LOS231062
LOS231063
LOS231063
LOS231064
LOS232029
LOS232025
TLR235007
LOS237000
TLR3100
LOS232030
LOS232054
LOS232023
LOS232030
LOS237000
TLR5901
LOS232055
LOS232026
LOSA3572 (12T)
LOSA3574 (14T)
LOS235024
TLR5905
LOS233014
LOS233015
TLR6313
LOS233011
LOS233013
LOS231030
TLR336005
LOSB2906
LOS233027
LOS233025
LOS233026
LOS233028
LOS236000
LOS235012
TLR6352
TLR235007
LOS234022
LOS234035
LOS234037
LOS234021
LOS234023
LOS234019
TLR5909
TLR5911
TLR5964
LOS234016
LOS234018
LOS237001
LOS234021
LOS234018
LOS232032
LOS232032
TLR5911
LOS231057
TLR6313
TLR5964
LOS231057
TLR6313
TLR5905
LOS235026
LOSA6940
LOS232031
LOS234016
TLR255008
LOS232030
LOS232030
LOS237000
LOS237000
LOS232023
LOS232028
LOS237002
LOS237002
LOS232024
LOS232023
LOS232026
LOS232026
LOS237000
LOS232030
LOS232029
LOS232026
LOS232023
TLR5965
LOS232023
LOS237000
LOS232027
LOS232023
TLR5933
LOS232030
LOS231027
LOS231027
LOS231026
TLR5904
TLR6313
TLR5904
TLR5910
LOS231057
LOS231024
LOS231057
LOS231054
LOS231026
LOS231033
LOS232026
TLR5963
TLR5964
TLR5932
LOS232054
LOS231031
SPMS614
SPMSR6100AT
TLR5904
LOS232029
LOS232023
TLR5904 TLR5964
LOS232027
LOS237002
LOS237002
LOS232024
TLR5911
TLR5911
TLR5905
LOS232031
TLR336000
TLR256005
LOS237001
LOSA6940
LOS234021
LOS234023
TLR255013
TLR5963
LOS234020
LOS234021
TLR6313
TLR6313
TLR6313
LOS234017
LOS234019
LOS234036
TLR235007
TLR5903
TLR5903
TLR5963
TLR5963
LOS235011
LOS231054t
LOS235025
TLR6313
TLR5908
LOS230079
TLR5904
LOS230079
LOS230078
LOS230078
LOS230078
LOS230079
LOS230079
LOS230079
LOS230079
LOS230079
LOS230080
LOS234038
LOS234038
LOS43028
LOS235025
LOS235025
TLR5903
TLR5903
TLR5903
TLR5903
TLR5903
TLR5901
TLR5901
TLR5901
TLR5903
TLR5903
TLR5903
TLR5901
LOS234038
TLR5901
TLR5903
TLR5901
TLR5903
LOS231065
LOS231065
LOS231065
TLR5901
TLR5901
LOS231065
TLR5901
TLR5901
LOS230076
LOS230077
LOS230079
TLR5901
TLR5903
TLR5962
TLR5962
TLR5963
TLR5903
SPMXSM2200
LOS231064
LOS230079
LOS230079
60778.2 | ©2021 Horizon Hobby, LLC.
Losi, Tenacity, Firma, DX3, DSM, DSM2, DSMR, AVC, Active Vehicle Control, Fuze, IC5 and the Horizon Hobby logo are trademarks or
registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc.
The Lasernut name and logo and vehicle cage design are property of Cody Waggoner, used under license.
All other trademarks, service marks and logos are property of their respective owners.
US 9,320,977, US 10,528,060, US 9,930,567. US 10,419,970. US 10,849,013. Other patents pending.
Updated 03/21 | LOS03028
WWW.LOSI.COM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18

Losi LOS03028T1 Le manuel du propriétaire

Catégorie
Jouets télécommandés
Taper
Le manuel du propriétaire

dans d''autres langues