Axial AXI03013 Bomber Rock Racer Manuel utilisateur
- Catégorie
- Jouets télécommandés
- Taper
- Manuel utilisateur
EN
2
Age Recommendation: Not for children under 14 years. This is not a toy.
WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the
product correctly can result in damage to the product, personal property and cause serious injury.
This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this
Product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children
without direct adult supervision. Do not use with incompatible components or alter this product in any way outside of the instructions provided by Horizon
Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the
manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.
NOTICE
All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC.
For up-to-date product literature, visit horizonhobby.com or towerhobbies.com and click on the support or resources tab for this product.
MEANING OF SPECIAL LANGUAGE
The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:
WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a
high probability of superficial injury.
CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.
NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no possibility of injury.
As the user of this product, you are solely responsible for operating in a manner that does not endanger yourself and others or result in damage to the
product or property of others.
This model is controlled by a radio signal subject to interference from many sources outside your control. This interference can cause momentary loss of
control, so it is advisable to always keep a safe distance in all directions around your model as this margin will help avoid collisions or injury.
• Never operate your model with low transmitter batteries.
• Always operate your model in open spaces away from full-size vehicles,
traffic and people.
• Never operate the model in the street or in populated areas for any reason.
• Carefully follow the directions and warnings for this and any optional
support equipment (chargers, rechargeable battery packs, etc.) you use.
• Keep all chemicals, small parts and anything electrical out of the reach
of children.
• Never lick or place any portion of the model in your mouth as it could
cause serious injury or even death.
• Exercise caution when using tools and sharp instruments.
• Take care during maintenance as some parts may have sharp edges.
• Immediately after using your model, do NOT touch equipment such as
the motor, electronic speed control and battery, because they generate
high temperatures. You may burn yourself seriously touching them.
• Do not put fingers or any objects inside rotating and moving parts, as this
may cause damage or serious injury.
• Always turn on your transmitter before you turn on the receiver in the
car. Always turn off the receiver before turning your transmitter off.
• Keep the wheels of the model off the ground when checking the
operation of the radio equipment.
SAFETY PRECAUTIONS AND WARNINGS
WARNING AGAINST COUNTERFEIT PRODUCTS: Always purchase from a Horizon Hobby, LLC authorized dealer to ensure authentic
high-quality Spektrum product. Horizon Hobby, LLC disclaims all support and warranty with regards, but not limited to, compatibility and
performance of counterfeit products or products claiming compatibility with DSM® or Spektrum technology.
EN
3
Your new Horizon Hobby vehicle has been designed and built with a
combination of waterproof and water-resistant components to allow you to
operate the product in many “wet conditions,” including puddles, creeks,
wet grass, snow and even rain.
While the entire vehicle is highly water-resistant, it is not completely
waterproof and your vehicle should NOT be treated like a submarine. The
various electronic components used in the vehicle, such as the Electronic
Speed Control (ESC), servo(s) and receiver are waterproof, however, most
of the mechanical components are water-resistant and should not be
submerged.
Metal parts, including the bearings, hinge pins, screws and nuts, as well
as the contacts in the electrical cables, will be susceptible to corrosion if
additional maintenance is not performed after running in wet conditions.
To maximize the long-term performance of your vehicle and to keep
the warranty intact, the procedures described in the “Wet Conditions
Maintenance” section below must be performed regularly if you choose
to run in wet conditions. If you are not willing to perform the additional
care and maintenance required, then you should not operate the vehicle in
those conditions.
CAUTION: Failure to exercise caution while using this product
and complying with the following precautions could result in
product malfunction and/or void the warranty.
GENERAL PRECAUTIONS
• Read through the wet conditions maintenance procedures and make sure
that you have all the tools you will need to properly maintain your vehicle.
• Not all batteries can be used in wet conditions. Consult the battery
manufacturer before use. Caution should be taken when using Li-Po
batteries in wet conditions.
• Most transmitters are not water-resistant. Consult your transmitter’s
manual or the manufacturer before operation.
• Never operate your transmitter or vehicle where lightning may be present.
• Do not operate your vehicle where it could come in contact with salt
water (ocean water or water on salt-covered roads), contaminated or
polluted water. Salt water is very conductive and highly corrosive, so
use caution.
• Even minimal water contact can reduce the life of your motor if it
has not been certified as water-resistant or waterproof. If the motor
becomes excessively wet, apply very light throttle until the water is
mostly removed from the motor. Running a wet motor at high speeds may
rapidly damage the motor.
• Driving in wet conditions can reduce the life of the motor. The additional
resistance of operating in water causes excess strain. Alter the gear ratio
by using a smaller pinion or larger spur gear. This will increase torque (and
motor life) when running in mud, deeper puddles, or any wet conditions
that will increase the load on the motor for an extended period of time.
WET CONDITIONS MAINTENANCE
• Drain any water that has collected in the tires by spinning them at high
speed. With the body removed, place the vehicle upside down and pull full
throttle for a few short bursts until the water has been removed.
CAUTION: Always keep hands, fingers, tools and any loose or
hanging objects away from rotating parts when performing the
above drying technique.
• Remove the battery pack(s) and dry the contacts. If you have an air
compressor or a can of compressed air, blow out any water that may be
inside the recessed connector housing.
• Remove the tires/wheels from the vehicle and gently rinse the mud and
dirt off with a garden hose. Avoid rinsing the bearings and transmission.
NOTICE: Never use a pressure washer to clean your vehicle.
• Use an air compressor or a can of compressed air to dry the vehicle and
help remove any water that may have gotten into small crevices or corners.
• Spray the bearings, drive train, fasteners and other metal parts with a
water-displacing light oil. Do not spray the motor.
• Let the vehicle air dry before you store it. Water (and oil) may continue
to drip for a few hours.
• Increase the frequency of disassembly, inspection and lubrication of the
following:
-Front and rear axle hub assembly bearings.
-All transmission cases, gears and differentials.
-Motor—clean with an aerosol motor cleaner and re-oil the bushings
with lightweight motor oil.
WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS
TABLE OF CONTENTS
Water-resistant Vehicle with Waterproof Electronics ..................................... 3
box Contents ............................................................................................................ 4
Required Equipment ............................................................................................... 4
recommended tools ................................................................................................ 4
Getting started checklist........................................................................................ 4
Vehicle parts ............................................................................................................ 5
Charge the vehicle battery .................................................................................... 6
Install the transmitter batteries ............................................................................ 6
Transmitter functions ............................................................................................. 6
Install the Vehicle Battery ..................................................................................... 7
Binding ...................................................................................................................... 8
Range-checking the radio system ....................................................................... 8
MAINTAINING YOUR VEHICLE ............................................................................. 9
DYNS2213 Forward/reverse ESC with drag brake .......................................... 10
Gear Ratio............................................................................................................... 11
Troubleshooting ..................................................................................................... 11
Limited Warranty ................................................................................................... 11
Warranty and Service Contact Information ..................................................... 12
FCC Information ..................................................................................................... 12
IC Information ........................................................................................................ 13
Compliance Information for the European Union ............................................ 13
Parts reference ..................................................................................................... 47
Exploded views...................................................................................................... 55
Parts Lists ............................................................................................................... 60
Optional Parts ........................................................................................................ 63
EN
4
BOX CONTENTS
GETTING STARTED CHECKLIST
Read the manual
Familiarize yourself with the vehicle and its components
Check all screws, especially the driveshaft setscrews, for tightness
from the factory
Charge the vehicle battery
Install 4 AA batteries in the transmitter
Power on the transmitter
Install the vehicle battery in the vehicle
Check for proper function of the throttle and steering
Range check the radio system
Drive the vehicle, challenge yourself and have FUN!
Perform any necessary vehicle maintenance
• Parts Bag • Cross Wrench
• Battery charger compatible with
the chosen vehicle battery type
• (4) AA Alkaline batteries • 3s LiPo Battery
• Hex Drivers (1.5, 2.0, 2.5mm)
• Hobby Knife • Side Cutter
• Curved Scissors • Long-nose Plier
• Spektrum™ DX3™ 2.4GHz Transmitter (SPMS2340T)
• KOH Special Edition RR10™ Bomber 1/10th 4WD RTR (AXI03013)
- SR315 3CH Receiver (SPMSR315)
- S614 15KG Servo (SPMS614)
- 35T Brushed Motor (AX31312)
- AE-5L ESC w/LED (DYNS2213)
REQUIRED EQUIPMENT
RECOMMENDED TOOLS
• 5-9 Cell NiMH/NiCd battery
(IC3® Connector Required)
OR
EN
5
VEHICLE PARTS
Steering Servo
Steering Knuckle
Battery Tray
Spare Tire Carrier
Spur/Pinion/Slipper
(Under Cover)
Transmission
Driveshaft
Upper 4-link Bar
Differential
(inside axle housing)
C-Hub
Electronic Speed Control
(ESC)
Motor
Lower 4-link Bar
Shock Absorber
Receiver Box
Steering Rack
EN
6
INSTALL THE TRANSMITTER BATTERIES
TRANSMITTER FUNCTIONS
This transmitter requires 4 AA batteries.
1. Remove the battery cover from the transmitter.
2. Install the batteries as shown.
3. Install the battery cover.
CAUTION: NEVER remove the transmitter batteries while the model
is powered on. Loss of model control, damage, or injury may occur.
CAUTION: If using rechargeable batteries, charge only
rechargeable batteries. Charging non-rechargeable batteries may
cause the batteries to burst, resulting in injury to persons and/or damage
to property.
CAUTION: Risk of explosion if battery is replaced by an incorrect
type. Dispose of used batteries according to national regulations.
A. Servo Reversing
To reverse the Throttle (TH) or Steering (ST) channel, switch the position
of the correlating switch—“N” is for normal, “R” is for reverse.
B. Throttle Trim
Adjusts the throttle neutral point
C. Steering Trim
Adjusts the steering center point. Normally, the steering trim is adjusted
until the vehicle tracks straight.
D. Brake Rate
Adjust Brake rate.(For use with AVC Rx’s)
E. Steering Rate
Adjusts the end point of the steering
F. Indicator Lights
• Solid red lights: Indicates radio connectivity and adequate battery power
• Flashing red lights: Indicates the battery voltage is critically low.
Replace batteries
G. Throttle Limit
Limits throttle output to 50/75/100%
Select 50% or 75% for less experienced drivers or when you are driving
the vehicle in a small area.
H. Antenna
I. Power Button
J. Throttle/Brake
K. Steering Wheel
G
J
I
H
K
A
B
D
FE
C
Follow the manufacturer’s directions for your charger to properly charge
the vehicle battery.
CAUTION: Only use chargers designed to charge the chosen
battery type. Using an incorrect charger or incorrect charger
settings could result in a fire causing personal injury or damage to property.
CHARGE THE VEHICLE BATTERY
EN
7
INSTALL THE VEHICLE BATTERY
1. Turn on the transmitter. 2. Connect the battery.
3. Install the battery.
4. Close the battery tray and hood.
Power to the vehicle is controlled by
connecting/disconnecting the battery.
EN
8
BINDING
The radio system should be checked before operating the vehicle to ensure proper operation and adequate range.
1. Turn on the transmitter.
2. Connect the battery in the vehicle.
3. Have a friend hold the vehicle while keeping hands and loose clothing away from moving parts.
4. Walk away until you are at the maximum planned operating distance from the vehicle.
5. Turn the steering wheel side to side and operate the throttle, both forward and reverse, checking for any erratic behavior.
6. If any erratic behavior is exhibited, DO NOT operate the vehicle. Call customer service for assistance.
RANGE-CHECKING THE RADIO SYSTEM
Binding is the process of programming the receiver to recognize the
GUID (Globally Unique Identifier) code of a single specific transmitter. The
SPM2340 transmitter and SR315 receiver are bound from the factory. If you
need to rebind, follow the instructions below.
1. Connect a fully charged battery pack to the ESC.
2. Center ST Trim and TH TRIM dials on the transmitter.
3. Power on the ESC.
4. Press the button on the SR315 to start bind mode. LED on SR315 will
flash.
5. While holding Bind button on the Transmitter, press Power Button to
power on the Transmitter. Release bind button when LED on SR315
stops flashing.
6. Vehicle is ready to operate.
You must rebind when:
• Different failsafe positions are desired e.g., when throttle or steering
reversing has been changed.
• Binding the receiver to a different transmitter.
EN
9
Just like a full size car or truck your RC vehicle must undergo periodic maintenance in order to ensure peak performance. Preventative maintenance
will also help avoid needless breakages which could result in costly repairs. Below are some suggestions to properly maintain your vehicle.
Replace any
noticeable bent or
broken parts
Check the wheel nuts
for tightness
If applicable, check
the slipper clutch for
proper operation
Check for wear on
the ball joints in
the steering and
suspension links
(replace if necessary)
Ensure the wheel
beads are still firmly
bonded around the
entire circumference
of the rim
Check the receiver
antenna for damage
Check driveshaft
set screws and
apply thread
locking compound if
necessary
Keep the chassis free
of dirt and debris
Check the steering
operation for any
binding
Inspect shock
absorbers for smooth
dampened operation
Check for loose
screws on the chassis,
especially the knuckle,
C-hub and axle lockout
screws
Inspect the spur
and pinion gears for
damage
Check for any loose
connections or frayed
wiring
Check the driveline
for smooth, bind free
operation
Replace the
transmitter batteries
when indicated by
the transmitter, as
described in the
Transmitter Functions
section
MAINTAINING YOUR VEHICLE
EN
10
Battery ESC
Red
Black
Motor
DYNS2213 FORWARD/REVERSE ESC WITH DRAG BRAKE
To Receiver
Throttle Channel
SETUP
Throttle calibration should not be needed out of the box. However, in order
to make the throttle range of different transmitters, the calibration of the
ESC is necessary:
• Mount the ESC in an area that is well ventilated and isolated from
vibration and shock.
• Connect the ESC motor wires to the motor red-to-red and black-to-black.
• Plug the receiver into the throttle channel of the receiver.
• Before plugging the battery into the ESC, make sure your transmitter is
on and the throttle trim is set to zero.
• Connect the battery to the ESC. The vehicle will be powered on when the
battery is connected.
CAUTION: Keep all body parts and loose clothing away from any
moving parts while the battery is connected to the ESC.
CAUTION: Always connect the ESC only to a proper power
source that has the correct voltage and polarity. Incorrect
voltages or reversed polarity will damage the ESCng. Damage to the ESC
caused by improper voltage or polarity is not covered under warranty.
• Test forward and reverse control using the transmitter.
To calibrate the ESC:
• Power the transmitter on and set the throttle control to neutral.
• Connect the battery to the ESC and wait 3 seconds to let the ESC initiate
a self-test and automatic throttle calibration.
• The ESC is ready to run when a long beep sound is emitted from the motor.
• Always disconnect the battery when the vehicle is not in use.
IMPORTANT: The LiPo cut-off is set to “ON” from the factory.
SPECIFICATIONS
Type Brushed
Constant/Peak 60A/360A
Resistance 0.0008 Ohms
Function Forward/Brake/Reverse, Forward/Brake,
Forward/Reverse (Crawler Mode)
Vehicle Type 1/10 on-road and off-road; 1/10 rock crawler
Operation Proportional forward, proportional reverse with
braking delay, Crawler Mode
Battery Type/Input
Voltage 2–3 cell Li-Po/Li-Fe; 5–7 cell Ni-MH/Ni-Cd
Motor Type 540-/550-size closed endbell motors: 2S Li-Po
down to 12T;3S Li-Po down to 35T
BEC Output 6V/3A
Overload Protection Thermal
Dimensions 35.6mm x 34mm x 18mm (1.40 in x 1.34 in x 0.71 in)
Weigh 40 g(1.41 oz) with wires
Battery Connector EC3™ connector
Motor Connector 3.5mm Tamiya-style Bullet
LED INDICATOR
OPERATION LED STATUS SOUND
Stop OFF
Forward partial throttle Blinks
Full Throttle Solid
Reverse Blinks
Partial Brake Blinks
Full Brake Blinks
Ni-MH/Ni-CD Battery 1 Short Beep
2S Li-Po Battery 2 Short Beeps
3S Li-Po Battery 3 Short Beeps
ESC Ready 1 Long Beep
Battery Low Voltage Blinks
Overheat Blinks
Mode
Battery
(BATT)
Forward/
Brake/
Reverse
(F/B/R)
50% Drag
Brake
100% Drag
Brake
Li-Po Ni-MH
EN
11
TROUBLESHOOTING
What this Warranty Covers
Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the
product purchased (the “Product”) will be free from defects in materials
and workmanship for a period of 2 years from the date of purchase.
What is Not Covered
This warranty is not transferable and does not cover (i) cosmetic damage,
(ii) damage due to acts of God, accident, misuse, abuse, negligence,
commercial use, or due to improper use, installation, operation or
maintenance, (iii) modification of or to any part of the Product, (iv) attempted
service by anyone other than a Horizon Hobby authorized service center, (v)
Product not purchased from an authorized Horizon dealer, or (vi) Product not
compliant with applicable technical regulations or (vii) use that violates any
applicable laws, rules, or regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO
OTHER WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS
ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT
LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE
PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED
THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE
PURCHASER’S INTENDED USE.
Purchaser’s Remedy
Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall
be that Horizon will, at its option, either (i) service, or (ii) replace, any
Product determined by Horizon to be defective. Horizon reserves the right
to inspect any and all Product(s) involved in a warranty claim. Service
or replacement decisions are at the sole discretion of Horizon. Proof of
purchase is required for all warranty claims. SERVICE OR REPLACEMENT
AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER’S SOLE AND
EXCLUSIVE REMEDY.
Limitation of Liability
HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL
OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION
OR COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH
CLAIM IS BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT
LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in
no event shall the liability of Horizon exceed the individual price of the
Product on which liability is asserted. As Horizon has no control over use,
setup, final assembly, modification or misuse, no liability shall be assumed
nor accepted for any resulting damage or injury. By the act of use, setup
or assembly, the user accepts all resulting liability. If you as the purchaser
or user are not prepared to accept the liability associated with the use of
the Product, purchaser is advised to return the Product immediately in new
and unused condition to the place of purchase.
Law
These terms are governed by Illinois law (without regard to conflict of law
principals). This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state. Horizon reserves the right to
change or modify this warranty at any time without notice.
WARRANTY SERVICES
Questions, Assistance, and Services
Your local hobby store and/or place of purchase cannot provide warranty
support or service. Once assembly, setup or use of the Product has been
started, you must contact your local distributor or Horizon directly. This
will enable Horizon to better answer your questions and service you in
the event that you may need any assistance. For questions or assistance,
please visit our website at www.horizonhobby.com, submit a Product
Support Inquiry, or call the toll free telephone number referenced in the
Warranty and Service Contact Information section to speak with a Product
Support representative.
LIMITED WARRANTY
PROBLEM POSSIBLE CAUSE SOLUTION
Vehicle does not move
Batteries are not installed properly in the transmitter Ensure the transmitter batteries are properly installed
Weak or no battery in the vehicle Install a freshly charged vehicle battery
Damaged motor Replace the motor
Frayed or broken wiring Replace any damaged wiring
ESC is shut down by heat protection circuit Allow the ESC to cool down completely
Loss of vehicle control
Improper antenna placement Ensure the transmitter antenna is not blocked and the receiver antenna
is located properly
Weak or no batteries in the transmitter or vehicle Install a freshly charged vehicle battery and new transmitter batteries
Neutral or trim position is incorrect Adjust the steering trim
Receiver and/or battery not connected properly Check all receiver and battery connections
Steering and/or throttle
function is reversed
Servo travel is reversed at the transmitter Set the transmitter servo reversing switch to the correct position
Motor wires are not connected properly Check all motor wires for correct polarity and secure connection
GEAR RATIO
32 Pitch 38T/13T (Stock Gearing AX30392 or HD AX30395)
Spur Gear
Pinion 56 60 64 68
11 28.85 30.91 32.97 35.03
12 26.44 28.33 30.22 32.11
13 24.41 26.15 27.90 29.64
14 22.67 24.88 25.90 27.52
15 21.15 22.67 24.18 25.69
16 19.83 21.25 22.67 24.08
17 18.67 20.00 21.33 22.67
Use this equation to calculate the final drive ratio:
Final Drive Gear Ratio = Spur
Pinion X 5.67
Slower - More Torque
Faster - Less Torque
39.64:1
16.42:1
EN
12
FCC INFORMATION
CONTAINS FCC ID: BRWKATY1T
FCC ID: BRWSRIRVINGV1
This equipment complies with FCC and IC radiation exposure limits set
forth for an uncontrolled environment. This equipment should be installed
and operated with minimum distance 20cm between the radiator and/or
antenna and your body (excluding fingers, hands, wrists, ankles and feet).
This transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
SUPPLIER’S DECLARATION OF CONFORMITY
Axial KOH Special Edition RR10 Bomber 1/10th 4WD RTR (AXI03013)
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
CAUTION: changes or modifications not expressly approved by
the party responsible for compliance could void the user’s
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Horizon Hobby, LLC
2904 Research Rd.,
Champaign, IL 61822
Email: compliance@horizonhobby.com
Web: HorizonHobby.com
Country of Purchase Horizon Hobby Contact Information Address
United States of America
Horizon Service Center
(Repairs and Repair Requests) servicecenter.horizonhobby.com/RequestForm/
2904 Research Rd
Champaign, IL 61822
Horizon Product Support
(Product Technical Assistance)
productsupport@horizonhobby.com
877-504-0233
Sales websales@horizonhobby.com
800-338-4639
European Union Horizon Technischer Service service@horizonhobby.eu Hanskampring 9
D 22885 Barsbüttel, Germany
Sales: Horizon Hobby GmbH +49 (0) 4121 2655 100
WARRANTY AND SERVICE CONTACT INFORMATION
Inspection or Services
If this Product needs to be inspected or serviced and is compliant in the
country you live and use the Product in, please use the Horizon Online
Service Request submission process found on our website or call Horizon
to obtain a Return Merchandise Authorization (RMA) number. Pack the
Product securely using a shipping carton. Please note that original boxes
may be included, but are not designed to withstand the rigors of shipping
without additional protection. Ship via a carrier that provides tracking
and insurance for lost or damaged parcels, as Horizon is not responsible
for merchandise until it arrives and is accepted at our facility. An Online
Service Request is available at http://www.horizonhobby.com/content/
service-center_render-service-center. If you do not have internet access,
please contact Horizon Product Support to obtain a RMA number along
with instructions for submitting your product for service. When calling
Horizon, you will be asked to provide your complete name, street address,
email address and phone number where you can be reached during
business hours. When sending product into Horizon, please include
your RMA number, a list of the included items, and a brief summary of
the problem. A copy of your original sales receipt must be included for
warranty consideration. Be sure your name, address, and RMA number are
clearly written on the outside of the shipping carton.
NOTICE: Do not ship Li-Po batteries to Horizon. If you have any issue
with a Li-Po battery, please contact the appropriate Horizon Product
Support office.
Warranty Requirements
For Warranty consideration, you must include your original sales receipt
verifying the proof-of-purchase date. Provided warranty conditions have
been met, your Product will be serviced or replaced free of charge.
Service or replacement decisions are at the sole discretion of Horizon.
Non-Warranty Service
Should your service not be covered by warranty, service will be completed
and payment will be required without notification or estimate of the
expense unless the expense exceeds 50% of the retail purchase cost. By
submitting the item for service you are agreeing to payment of the service
without notification. Service estimates are available upon request. You
must include this request with your item submitted for service. Non-
warranty service estimates will be billed a minimum of 1/2 hour of labor. In
addition you will be billed for return freight. Horizon accepts money orders
and cashier’s checks, as well as Visa, MasterCard, American Express,
and Discover cards. By submitting any item to Horizon for service, you are
agreeing to Horizon’s Terms and Conditions found on our website http://
www.horizonhobby.com/content/service-center_render-service-center.
ATTENTION: Horizon service is limited to Product compliant in the
country of use and ownership. If received, a non-compliant Product will
not be serviced. Further, the sender will be responsible for arranging
return shipment of the un-serviced Product, through a carrier of the
sender’s choice and at the sender’s expense. Horizon will hold non-
compliant Product for a period of 60 days from notification, after which
it will be discarded.
10/15
EN
13
EU COMPLIANCE STATEMENT:
Axial KOH Special Edition RR10 Bomber 1/10th 4WD RTR
(AXI03013)
Hereby, Horizon Hobby, LLC declares that the device is in compliance with
the following: EU Radio Equipment Directive 2014/53/EU; RoHS 2 Directive
2011/65/EU; RoHS 3 Directive - Amending 2011/65/EU Annex II 2015/863.
The full text of the EU declaration of conformity is available at the following
internet address: https://www.horizonhobby.com/content/support-render-
compliance.
Wireless Frequency Range and Wireless Output Power
Transmitter
2402.0 - 2478.0 MHz
17.7 dBm
Receiver
2404-2476 MHz
-1.33 dBm
EU Manufacturer of Record:
Horizon Hobby, LLC
2904 Research Road
Champaign, IL 61822 USA
EU Importer of Record:
Horizon Hobby, GmbH
Hanskampring 9
22885 Barsbüttel Germany
WEEE NOTICE:
This appliance is labeled in accordance with European
Directive 2012/19/EU concerning waste of electrical and
electronic equipment (WEEE). This label indicates that this
product should not be disposed of with household waste. It
should be deposited at an appropriate facility to enable
recovery and recycling.
IC INFORMATION
COMPLIANCE INFORMATION FOR THE EUROPEAN UNION
CAN ICES-3 (B)/NMB-3(B)
Contains IC: 6157A-KATY1T
IC: 6157A-SRIRVINGV1
This device contains license-exempt transmitter(s)/receivers(s) that
comply with Innovation, Science, and Economic Development Canada’s
license-exempt RSS(s). Operation is subject to the following 2 conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that
may cause undesired operation of the device.
EN
4747
AX80035 (x2) / AX31301 (Blue) (x2)
10mm Shock Caps Parts Tree
10mm Stoßdämpfer-Teilebaum
Arbre des pièces d’amortisseurs 10mm
Set ricambi ammortizzatore 10 mm
AX31108 (x1)
2-Speed Hi/Lo Transmission Case
2-Geschwindigkeiten Hi/Lo Getriebeabdeckung
Boîtier de la transmission élevé/faible 2vitesses
Scatola trasmissione 2 velocità alta/bassa (HI/LO)
AX31049 (x2)
Helmet Set (Black)
Helm-Set (schwarz)
Ensemble de casque (noir)
Set elmetti (nero)
AX31324 (x1)
RR10 Transfer Case
RR10 Transfergehäuse
Boîte de transfert RR10
Custodia di trasferimento RR10
AX31333 (x1)
RR10 Skid Plate
RR10 Gleitbrett
Plaque de protection RR10
Piastra di protezione RR10
AX31323 (x1)
RR10 Electronics Box
RR10 Elektronikbox
Boîtier des composants électroniques RR10
Scatola elettronica RR10
AX80034 (x2) / AX31300 (Blue) (x2)
10mm Shock Parts Tree 2
10mm Stoßdämpfer-Teilebaum
Arbre des pièces d’amortisseurs 10mm
Set ricambi ammortizzatore 10 mm
AX80071 (x1)
Straight Axle Adapter Rear
Gerader Achsadapter hinten
Adaptateur d’essieu droit arrière
Adattatore assale dritto posteriore
AX31317 (x2)
AR66 Differential Covers
AR66 Differenzialgehäuse
Couvercles de différentiel AR66
Carter differenziale AR66
AX31316 (x1)
AR60 Steering knuckles
AR60 Lenkrollen
Rotules de direction AR60
Fusi a snodo AR60
AX80018 (x3)
Hardware parts tree
Hardware-Teilebaum
Arbre des pièces de quincaillerie
Set bulloneria
AX80033 (x2)
10mm shock parts tree
10mm Stoßdämpfer-Teilebaum
Arbre des pièces d’amortisseurs 10mm
Set ricambi ammortizzatore 10 mm
AX31114 (x2)
WB8-HD Standard driveshaft
WB8-HD Standard-Antriebswelle
Arbre de transmission standard WB8-HD
Albero di trasmissione standard WB8-HD
PARTS REFERENCE // TEILEREFERENZ // RÉFÉRENCES DES PIÈCES // RIFERIMENTO COMPONENTI
EN
4848
AX31332 (x1)
RR10 Battery Tray Chassis Components 2
RR10 Akkufach Karosseriebauteile 2
Composants du châssis du support de batterie RR10 2
2 componenti telaio supporto batteria RR10
AX31109 (x1)
Yeti™ Rear 4 Link Set
Yeti™ 4-gliedriger Gelenksatz hinten
Ensemble de 4 bras arrière Yeti™
Set 4 braccetti Yeti™ posteriore
AX80083 (x1)
Wraith Links Set
Wraith-Gestängesatz
Ensemble de bras Wraith
Set leveraggi Wraith
AX31318 (x1)
RR10 Battery Tray Chassis Components
RR10 Akkufach Karosseriebauteile
Composants du châssis du support de batterie RR10
Componenti telaio supporto batteria RR10
AX31107 (x1)
2-Speed Hi/Lo Transmission Spur Gear Cover
2-Geschwindigkeiten Hi/Lo Getriebe Stirnradabdeckung
Cache de l’engrenage cylindrique de la transmission élevé/faible 2vitesses
Carter ingranaggi trasmissione 2 velocità alta/bassa (HI/LO)
AX31354 (x1)
AR60 Heavy Duty C-Hub Carrier
AR60 robuster C-Nabenträger
Support de moyeu en C haute résistance AR60
Supporto caster block Heavy Duty AR60
AXI43007 (x4)
2.2 Raceline Monster Beadlock Wheel (Satin)
2.2 Raceline Monster Beadlock-Rad (Satin)
Roue à verrou de talon 2,2 Raceline Monster (satinée)
Cerchione Beadlock Raceline Monster 2.2 (Satinato)
AXI43006 (x4)
2.2 Trail Ready HD Beadlock Wheel (Satin)
2.2 Trail Ready HD Beadlock-Rad (Satin)
Roue à verrou de talon 2,2 Trail Ready HD (satinée)
Cerchione Beadlock Trail Ready HD 2.2 (Satinato)
AX80002 (x2)
Diff Case - Small
Differentialgehäuse – Klein
Boîtier de différentiel - Petit
Scatola diff. - Piccola
AX80073 (x1)
AR60 OCP Steering Link
AR60 OCP-Lenkstange
Tringlerie de direction AR60 OCP
Braccetto sterzo AR60 OCP
AX80069 (x2)
Offset Axle Housing
Achsgehäuse mit Versatz
Carter d’essieu déporté
Carcassa assale offset
AX80072 (x1)
Offset Axle 4 Link Mount
Achse mit viergliedrigem Gestänge und Versatz
Support d’essieu déporté à 4 bras
Supporto braccetti 4-link offset assale
EN
4949
AX31096
AX31320 (x1)
RR10 Rear Cage Components
RR10 Hintere Gehäusebauteile
Composants de la cage arrière RR10
Componenti custodia posteriore RR10
AXI230014 (x1)
RR10 Rear Light Bar Mount
RR10 Hintere Leuchtbalkenhalterung
Support de rampe d’éclairage arrière RR10
Supporto barra luminosa posteriore RR10
AX31152 (x1)
Universal Rigid Light Bar Set
Starrer Universal-Leuchtbalkensatz
Rampe d’éclairage universelle rigide
Set barra luminosa rigida universale
AX31319 (x1)
RR10 Center Cage
RR10 Zentrales Gehäuse
Cage centrale RR10
Custodia centrale RR10
AX31125 (x1)
Yeti™ Fuel Cell
Yeti™ Treibstofftank
Réservoir de carburant Yeti™
Cella carburante Yeti™
AX31065 (x1)
Spur Gear 32P 64T
Stirnrad 32P 64T
Engrenage cylindrique 32P 64T
Corona 32P 64T
AX31106 (x1)
2-Speed Hi/Lo Transmission Motor Mount
2-Geschwindigkeiten Hi/Lo Getriebe Motorhalterung
Support moteur de la transmission élevé/faible 2vitesses
Supporto motore trasmissione 2 velocità alta/bassa (HI/LO)
EN
5050
AX31322(x1)
RR10 Cage Sides (Left and Right)
RR10 Gehäuseseiten (Links und Rechts)
Côtés de la cage RR10 (gauche et droite)
Scocca di protezione laterale (dx e sx) RR10
AX31321(x1)
RR10 Cage Lower Rails
RR10 Gehäuse untere Schienen
Rails inférieurs de la cage RR10
Guide inferiori custodia RR10
EN
5151
AX31131 (x1)
T-Case Gear Set
T-Case-Getriebesatz
Ensemble d’engrenages de boîte de transfert
Set ingranaggi scatola a T
AX30723 (x1)
Pinion 32DP 12T
Zahnradgetriebe, 32DP, 12T
Engrenage à pignons,, 32DP 12T
Pignone 32DP, 12T,
AX30500 (x2)
Heavy Duty Locker
Robuste Sicherung
Blocage haute résistance
Blocco differenziale Heavy Duty
AX31314 (x4)
Aluminum Shock Body 12x47.5mm
Aluminium Stoßdämpfergehäuse 12x47,5mmAluminum
Carrosserie d’amortisseurs en aluminium 12x47,5mm
Corpo ammortizzatore in alluminio 12x47,5mm
AX31130 (x1)
High Speed Transmission Gear Set (48P 26T, 48P 28T)
Hochgeschwindigkeits-Getriebesatz (48P 26T, 48P 28T)
Ensemble d’engrenages de transmission grande vitesse (48P 26T, 48P 28T)
Set ingranaggi trasmissione alta velocità (48P 26T, 48P 28T)
AXI231007 (x1)
Metal Servo Horn (23T)
Metallgetriebehorn (23T)
Renvoi du servo métallique (23T)
Servo squadretta in metallo (23 T)
AX30429 (x4)
Narrow 12mm aluminum hub
Schmale Aluminium-Nabe, 12mm
Moyeu étroit en aluminium de 12mm
Mozzo stretto in alluminio, 12 mm
AX30392 (x2)
Bevel Gear Set - 38T/13T
Kegelradgetriebesatz − 38T/13T
Ensemble d’engrenages coniques - 38T/13T
Set ingranaggi conici - 38T/13T
AX31148 (x4)
WB8-HD Driveshaft coupler set
WB8-HD-Antriebswellenkupplungssatz
Ensemble de couplage d’arbre de
transmission WB8-HD
Set accoppiamento albero
trasmissione WB8-HD
AX30413 (x1)
Slipper spring, 8.5 x 12
Gleitfeder, 8,5 x 12
Ressort de sabot, 8,5 x 12
Molla pattino, 8,5x12
AX30408 (x2)
Steel Input Shaft 5x29mm
Stahl-Eingangswelle 5 x 29 mm
Arbre d’entrée en acier 5 x 29 mm
Albero di entrata in acciaio 5x29 mm
AX30112 (x4)
Shock Diaphragm 13x4.5mm
Stoßdämpfermembran 13 x 4,5 mm
Membrane d’amortisseur 13 x 4,5 mmm
Diaframma ammortizzatore 13x4,5 mm
AX30113 (x4)
Rubber Bump Stop 3.6x7x4mm
Gummianschlag 3,6 x 7 x 4 mm
Butée en caoutchouc 3,6 x 7 x 4 mm
Fine corsa in gomma 3,6x7x4 mm
AX31083 (x1)
Radio box seals
Funkbox-Dichtungen
Joints du boîtier de radio
Guarnizioni vano radiocomando
AX30385 (x2)
Diff Gasket 16x25x0.5mm
Differentialdichtung 16 x 25 x 0,5 mm
Joint de différentiel 16 x 25 x 0,5 mm
Guarnizione differenziale 16x25x0,5 mm
EN
5252
AX31313 (x1)
Transfer Case Output Shaft (5x69mm)
Transfergehäuse Antriebswelle (5x69mm)
Arbre de sortie de la boîte de transfert (5x69mm)
Albero uscita scatola di trasferimento (5x69mm)
AX30155 (x4)
Shock Shaft 3x59.5mm
Kolbenstange, 3 x 59.5mm
Bras d’amortisseur, 3 x 59.5mm
Albero ammortizzatore, 3x59.5 mm
AX31129 (x1)
2-Speed Hi/Lo Transmission Bottom Shaft (5x75mm)
2-Geschwindigkeiten Hi/Lo untere Getriebewelle (5x75mm)
Arbre inférieur de la transmission élevé/faible 2vitesses (5x75mm)
Albero inferiore trasmissione 2 velocità alta/bassa (HI/LO) (5x75mm)
AX31127 (x1)
2-Speed Hi/Lo Transmission Top Shaft (5x91mm)
2-Geschwindigkeiten Hi/Lo obere Getriebewelle (5x91mm)
Arbre supérieur de la transmission élevé/faible 2vitesses (5x91mm)
Albero superiore trasmissione 2 velocità alta/bassa (HI/LO) (5x91mm)
AX30224 (x2) / AX31315 (Blue) (x2)
Spring 14x70mm 1.43 lbs/in
Feder 14x70mm 1,43lbs/in
Ressort 14x70mm 1,43 lb/po
Molla 14x70 mm 1,43 lbs/in
AX30221 (x2) / AX31336 (Blue) (x2)
Spring 14x70mm 3.27 lbs/in
Feder 14x70mm 3,27lbs/in
Ressort 14x70mm 3,27 lb/po
Molla 14x70 mm 3,27 lbs/in
AX31067 (x1)
Slipper Plate
Gleitplatte
Plaque de sabot
Piastra pattino
AX30368 (x2)
Axle, 6 x 39mm
Achse, 6 x 39mm
Essieu, 6x39mm
Assale ,6 x 39 mm
AX30419 (x1)
AR60 OCP Front Dogbone 7x69mm
AR60 OCP Vorderes Dogbone 7 x 69 mm
Dogbone avant AR60 OCP 7 x 69 mm
Cardano anteriore AR60 OCP 7x69 mm
AX30419 (x1)
AR60 OCP Front Dogbone 7x125mm
AR60 OCP Vorderes Dogbone 7 x 125 mm
Dogbone avant AR60 OCP 7 x 125 mm
Cardano anteriore AR60 OCP 7x125 mm
AX30776 (x1)
AR60 OCP Rear Axle 6x104.2mm
AR60 OCP Hinterachse 6 x 104,2 mm
Essieu arrière AR60 OCP 6 x 104,2 mm
Assale posteriore AR60 OCP 6x104,2 mm
AX30776 (x1)
AR60 OCP Rear Axle 6x160.2mm
AR60 OCP Hinterachse 6 x 160,2 mm
Essieu arrière AR60 OCP 6 x 160,2 mm
Assale posteriore AR60 OCP 6x160,2 mm
AX31059 (x2)
Slipper plate washer, 33 x 1mm
Gleitplattenunterlegscheibe, 33 x 1
mm
Rondelle de plaque de sabot, 33 x 1mm
Rondella piastra pattino, 33x1 mm
AX31068 (x2)
Slipper pad, 32.8 x 15.2 x 1mm
Gleitkissen 32,8 x 15,2 x 1mm
Sabot de piston, 32,8 x 15,2 x 1mm
Piastra guida, 32,8x15,2x1 mm
EN
5353
AXA1393 (x2)
E2.5 e-clip
E2.5 E-Clip
E-clip E2.5
E-clip E2.5
AXA1391 (x2)
E4 e-clip
E4 E-Clip
E-clip E4
E-clip E4
AXA1069 (x8)
Washer 2.7x6.7x0.5mm
Unterlegscheibe 2.7x 6.7 x 0,5mm
Rondelle 2.7x6.7x0,5mm
Rondella 2.7x 6.7 x 0,5mm
AXA1070 (x1)
Washer 3 x 6 x 0.5mm
Unterlegscheibe 3 x 6 x 0,5mm
Rondelle 3 x 6 x 0,5mm
Rondella 3x 6 x 0,5mm
AXA1202 (x8)
O-Ring 3.5 x 2mm
O-Ring 3,5 x 2mm
Joint torique 3,5 x 2mm
O-Ring 3.5 x 2mm
AXA1184 (x4)
O-Ring 7.5 x 1.5mm
O-Ring 7,5 x 1.5mm
Joint torique 7,5 x 1.5mm
O-Ring 7.5 x 1.5mm
AXA1221 (x20)
Bearing 5x11x4mm
Lager 5 x 11 x 4 mm
Roulement 5 x 11 x 4 mm
Cuscinetto 5x11x4 mm
AXA1230 (x6)
Bearing 10x15x4mm
Lager 10 x 15 x 4 mm
Roulement 10 x 15 x 4 mm
Cuscinetto 10x15x4 mm
AXA180 (x12)
M3x3mm Set Screw
M3 x 3 mm Schraubensatz
Vis de fixation M3 x 3 mm
Vite di arresto M3x3 mm
AXA291 (x1)
M4x4mm Set Screw
M4 x 4 mm Schraubensatz
Vis de fixation M4 x 4 mm
Vite di arresto M4x4 mm
AX31028 (x8)
Pin 2x11mm
Stift 2 x 11 mm
Goupille 2 x 11 mm
Perno 2 x 11 mm
AXA1053 (x3)
M3 Nylon Lock Nut
M3 Nylon-Feststellmutter
Contre-écrou en nylon M3
Controdado nylon M3
AXA1041 (x4)
M2.5 Nylon Lock Nut
M2.5 Nylon-Feststellmutter
Contre-écrou en nylon M2.5
Controdado nylon M2.5
AXA1052 (x6)
M3 Thin Nylon Locking Hex Nut
M3 dünne Nylon-Feststellmutter
Contre-écrou à six pans fin en nylon M3
Controdado esagonale nylon sottile M3
AXA1045 (x1)
M4 Nylon Lock Nut
M4 Nylon-Feststellmutter
Contre-écrou en nylon M4
Controdado nylon M4
AX31250 (x4)
M4 Serrated Nylon Lock Nut
Feststellflanschmutter (schwarz)
Contre-écrou en nylon strié (noir) M4
Controdado dentato nylon (nero) M4
AXA186 (x8)
M3x16mm Set Screw
M3 x 16 mm Schraubensatz
Vis de fixation M3 x 16 mm
Vite di arresto M3x16 mm
AXA0187 (x4)
M3x20mm Set Screw
M3 x 20 mm Schraubensatz
Vis de fixation M3 x 20 mm
Vite di arresto M3x20 mm
AXA1071 (x2)
Washer 4x8x0.5mm
Unterlegscheibe 4x 8 x 0,5mm
Rondelle 4x8x0,5mm
Rondella 4x 8 x 0,5mm
AX30163 (x5)
Pin 2x10mm
Stift 2 x 10 mm
Goupille 2 x 10 mm
Perno 2 x 10 mm
AXA087 (x8)
M3x16mm Hex Socket Cap Head
M3 x 16 mm Sechskant-Inbusschraube
Douille à six pans d’assemblage creuse M3 x16 mm
Vite testa cilindrica con esagono incassato M3x16 mm
AXA091 (x2)
M3x30mm Hex Socket Cap Head
M3 x 30 mm Sechskant-Inbusschraube
Douille à six pans d’assemblage creuse M3 x30 mm
Vite testa cilindrica con esagono incassato M3x30 mm
AXA015 (x16)
M2x10mm Hex Socket Cap Head
M2 x 10 mm Sechskant-Inbusschraube
Douille à six pans d’assemblage creuse M2 x 10 mm
Vite testa cilindrica con esagono incassato M2x10 mm
AXA013 (x5)
M2x6mm Hex Socket Cap Head
M2 x 6 mm Sechskant-Inbusschraube
Douille à six pans d’assemblage creuse M2 x 6 mm
Vite testa cilindrica con esagono incassato M2x6 mm
AXA0286 (x4)
Screw Shaft M4x2.5x12mm
Gewindeschaft M4 x 2,5 x 12 mm
Tige de vis M4 x 2,5 x 12 mm
Albero filettato M4 x 2,5 x 12 mm
AXA0023 (x28)
M2.6x8mm Cap Head
M2.6 x 8 mm Sechskant-Inbusschraube
Douille à six pans d’assemblage creuse M2.6 x8 mm
Vite testa cilindrica con esagono incassato M2.6x8 mm
AX31121 (x2)
M4x12mm Cap Head
M4 x 12 mm Sechskant-Inbusschraube
Douille à six pans d’assemblage creuse M4 x12 mm
Vite testa cilindrica con esagono incassato M4x12 mm
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
Axial AXI03013 Bomber Rock Racer Manuel utilisateur
- Catégorie
- Jouets télécommandés
- Taper
- Manuel utilisateur