Losi LOS03015 Le manuel du propriétaire

Marque: Losi

Modèle: LOS03015

Catégorie: Véhicules jouets

Taper: Le manuel du propriétaire

Ce manuel convient également à

Before operating this vehicle, please read all printed materials thoroughly.

Horizon Hobby is not responsible for inadvertent errors in this manual.

INSTRUCTION MANUAL

BEDIENUNGSANLEITUNG

MANUEL D’UTILISATION

MANUALE DI ISTRUZIONI

Battery and charger sold separately

NIGHT CRAWLER SE RTR: 1:10 4WD ROCK CRAWLER • INSTRUCTION MANUAL

Age Recommendation: Not for children under 14 years. This is not a toy.

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in dam-

age to the product, personal property and cause serious injury.

This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this Product in a safe and

responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. Do not use with

incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby, LLC. This manual contains instructions for safety, operation and mainte-

nance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.

WARNING AGAINST COUNTERFEIT PRODUCTS Always purchase from a Horizon Hobby, LLC authorized dealer to ensure authentic high-quality Spektrum product. Horizon

Hobby, LLC disclaims all support and warranty with regards, but not limited to, compatibility and performance of counterfeit products

or products claiming compatibility with DSM or Spektrum technology.

NOTICE

All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC.

For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product.

MEANING OF SPECIAL LANGUAGE

The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:

WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of superﬁcial injury.

CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.

NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no possibility of injury.

As the user of this product, you are solely responsible for operating in a manner that does not

endanger yourself and others or result in damage to the product or property of others.

This model is controlled by a radio signal subject to interference from many sources outside

your control. This interference can cause momentary loss of control, so it is advisable to

always keep a safe distance in all directions around your model as this margin will help avoid

collisions or injury.

•Never operate your model with low transmitter batteries.

•Always operate your model in open spaces away from full-size vehicles, traffic and people.

•Never operate the model in the street or in populated areas for any reason.

•Carefully follow the directions and warnings for this and any optional support equipment

(chargers, rechargeable battery packs, etc.) you use.

•Keep all chemicals, small parts and anything electrical out of the reach of children.

•Never lick or place any portion of the model in your mouth as it could cause serious injury

or even death.

•Exercise caution when using tools and sharp instruments.

•Take care during maintenance as some parts may have sharp edges.

•Immediately after using your model, do NOT touch equipment such as the motor, electronic

speed control and battery, because they generate high temperatures. You may burn yourself

seriously touching them.

•Do not put ﬁngers or any objects inside rotating and moving parts, as this may cause

damage or serious injury.

•Always turn on your transmitter before you turn on the receiver in the car. Always turn off the

receiver before turning your transmitter off.

•Keep the wheels of the model off the ground when checking the operation of the radio

equipment.

SAFETY PRECAUTIONS AND WARNINGS

Transmitter

Frequency 2.4GHz

Battery AA x 4

Servo

Power Supply 4.8V~6V

Output Torque 161 oz (4.6 kg-cm)

Operating Speed 0.24sec/60 degrees@6V

Size 40 x 40.5 x 24.5mm

Electronic Speed Control (ESC)

Input Voltage 2–3S LiPo; 5–7 cells NiMH/NiCd

Electric Capacity 60A ESC

BEC Voltage 6V/3A

Size 35.6 x 34 x 18mm

Weight 40 g

SPECIFICATIONS

TABLE OF CONTENTS

BOX CONTENTS ........................................................................................................3

WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS ..............................3

GENERAL PRECAUTIONS ................................................................................................... 3

WET CONDITIONS MAINTENANCE ....................................................................................3

QUICK START ............................................................................................................3

CHARGING THE BATTERY .........................................................................................3

INSTALLING THE BATTERY ........................................................................................ 4

TRANSMITTER CONTROLS ........................................................................................4

INSTALLING THE TRANSMITTER BATTERIES ........................................................................4

ESC CALIBRATION ....................................................................................................5

BINDING ..................................................................................................................5

DRIVING PRECAUTIONS ..........................................................................................5

POWERING ON THE VEHICLE .................................................................................... 5

BEFORE RUNNING YOUR VEHICLE ............................................................................ 5

RUN TIME ................................................................................................................. 5

TO IMPROVE RUN TIMES ...................................................................................................5

PERFORMING A CONTROL DIRECTION TEST.............................................................6

DYNAMITE® 60A WATERPROOF FWD/REV BRUSHED ESC (DYNS2210) ...................6

SPECIFICATIONS ...............................................................................................................6

ESC LED STATUS ...............................................................................................................6

AUDIBLE WARNING TONES ...............................................................................................6

ESC CALIBRATION PROCEDURE ........................................................................................6

CONNECTING THE ESC .....................................................................................................6

PROGRAMMING ...............................................................................................................6

DESCRIPTIONS ..................................................................................................................6

VEHICLE LEDs ...........................................................................................................6

DYNAMITE® 540 BRUSHED MOTOR (DYNS1216) ....................................................7

PRECAUTIONS ..................................................................................................................7

GEARING ......................................................................................................................... 7

CHANGING THE PINION GEAR/GEAR RATIO ......................................................................7

SETTING THE GEAR MESH .................................................................................................7

TROUBLESHOOTING GUIDE ......................................................................................7

LIMITED WARRANTY ...............................................................................................7

WARRANTY AND SERVICE CONTACT INFORMATION ................................................8

FCC STATEMENT ....................................................................................................... 8

IC INFORMATION .....................................................................................................8

COMPLIANCE INFORMATION FOR THE EUROPEAN UNION ......................................8

REPLACEMENT PARTS ......................................................................................30–31

RECOMMENDED PARTS..........................................................................................31

OPTIONAL PARTS ...................................................................................................31

EXPLODED VIEW ..............................................................................................32–35

NIGHT CRAWLER SE RTR: 1:10 4WD ROCK CRAWLER • INSTRUCTION MANUAL

2.4GHZ DIGITAL

RADIO SYSTEM

2.4GHZ DIGITAL

RADIO SYSTEM

NIGHT CRAWLER SE RTR: 1:10 4WD ROCK CRAWLER • INSTRUCTION MANUAL

Your new Horizon Hobby vehicle has been designed and built with a combination of

waterproof and water-resistant components to allow you to operate the product in many

“wet conditions,” including puddles, creeks, wet grass, snow and even rain.

While the entire vehicle is highly water-resistant, it is not completely waterproof and your

vehicle should NOT be treated like a submarine. The various electronic components used in the

vehicle, such as the Electronic Speed Control (ESC), servo(s) and receiver are waterproof, how-

ever, most of the mechanical components are water-resistant and should not be submerged.

Metal parts, including the bearings, hinge pins, screws and nuts, as well as the contacts

in the electrical cables, will be susceptible to corrosion if additional maintenance is not

performed after running in wet conditions. To maximize the long-term performance of your

vehicle and to keep the warranty intact, the procedures described in the “Wet Conditions

Maintenance” section below must be performed regularly if you choose to run in wet

conditions. If you are not willing to perform the additional care and maintenance

required, then you should not operate the vehicle in those conditions.

CAUTION: Failure to exercise caution while using this product and complying with the

following precautions could result in product malfunction and/or void the warranty.

GENERAL PRECAUTIONS

•Read through the wet conditions maintenance procedures and make sure that you

have all the tools you will need to properly maintain your vehicle.

•Not all batteries can be used in wet conditions. Consult the battery manufacturer before

use. Caution should be taken when using Li-Po batteries in wet conditions.

•Most transmitters are not water-resistant. Consult your transmitter’s manual or the

manufacturer before operation.

•Never operate your transmitter or vehicle where lightning may be present.

•Do not operate your vehicle where it could come in contact with salt water (ocean

water or water on salt-covered roads), contaminated or polluted water. Salt water

is very conductive and highly corrosive, so use caution.

•Even minimal water contact can reduce the life of your motor if it has not been certiﬁed as

water-resistant or waterproof. If the motor becomes excessively wet, apply very light throttle

until the water is mostly removed from the motor. Running a wet motor at high speeds may

rapidly damage the motor.

•Driving in wet conditions can reduce the life of the motor. The additional resistance of

operating in water causes excess strain. Alter the gear ratio by using a smaller pinion or larger

spur gear. This will increase torque (and motor life) when running in mud, deeper puddles, or

any wet conditions that will increase the load on the motor for an extended period of time.

WET CONDITIONS MAINTENANCE

•Drain any water that has collected in the tires by spinning them at high speed. With the

body removed, place the vehicle upside down and pull full throttle for a few short bursts

until the water has been removed.

CAUTION: Always keep hands, ﬁngers, tools and any loose or hanging objects

away from rotating parts when performing the above drying technique.

•Remove the battery pack(s) and dry the contacts. If you have an air compressor or a can of

compressed air, blow out any water that may be inside the recessed connector housing.

•Remove the tires/wheels from the vehicle and gently rinse the mud and dirt off with a

garden hose. Avoid rinsing the bearings and transmission.

NOTICE: Never use a pressure washer to clean your vehicle.

•Use an air compressor or a can of compressed air to dry the vehicle and help remove any

water that may have gotten into small crevices or corners.

•Spray the bearings, drive train, fasteners and other metal parts with a water-displacing light

oil. Do not spray the motor.

•Let the vehicle air dry before you store it. Water (and oil) may continue to drip for a few hours.

•Increase the frequency of disassembly, inspection and lubrication of the following:

- Front and rear axle hub assembly bearings.

- All transmission cases, gears and differentials.

- Motor—clean with an aerosol motor cleaner and re-oil the bushings

with lightweight motor oil.

WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS

QUICK START

Please read the entire manual to gain a full understanding of the vehicle, ﬁne-tuning the setup and performing maintenance.

1. Read the safety precautions found in this manual.

2. Charge a battery for the vehicle. Refer to the included charging warnings and

instructions for battery charging information.

3. Install the AA batteries in the transmitter. Only use alkaline

or rechargeable batteries.

4. Install the fully charged battery in the vehicle.

5. Power ON the transmitter and then the vehicle. Wait 5 seconds for the ESC to

initialize. Always power the transmitter ON before the vehicle and power it OFF

after the vehicle has been powered OFF.

6. Check the steering and throttle control directions. Verify that the servos are

moving in the correct direction.

7. Drive your vehicle.

8. Perform any necessary maintenance.

CHARGING THE BATTERY

BOX CONTENTS

• Losi

Night Crawler SE RTR: 1/10-Scale 4WD Rock Crawler

• Spektrum™ STX2

2CH 2.4GHz FHSS Transmitter (SPMSTX200)

• Spektrum™ STX2

2CH 2.4GHz FHSS Receiver (SPMSRX200)

• Spektrum™

9KG 23T Waterproof Servo (SPMS605)

• Dynamite

60A FWD/REV Brushed ESC (DYNS2210)

• Dynamite

35T 540 Brushed Motor (DYNS1216)

• 4 AA batteries (for transmitter)

Choose a battery designed to work with the Dynamite

Prophet™ Sport 50W AC/DC Charger

(DYNC2010CA) or the Dynamite

Prophet™ Sport LiPo 35W AC Charger (DYNC20005CA). We

recommend the Dynamite

Speedpack

7.2V 3300 mAh NiMH 6C Flat with EC3™ connector

(DYN1070EC) or the Dynamite

Reaction

7.4V 5000mAh2S 20C LiPo hardcase with EC3

connector (DYN9004EC).

NIGHT CRAWLER SE RTR: 1:10 4WD ROCK CRAWLER • INSTRUCTION MANUAL

INSTALLING THE BATTERY

INSTALLING THE TRANSMITTER BATTERIES

This transmitter requires 4 AA batteries.

1. Remove the battery cover from the transmitter.

2. Install the batteries as shown.

3. Install the battery cover.

CAUTION: If using rechargeable batteries, charge only rechargeable batteries.

Charging non-rechargeable batteries may cause the batteries to burst, resulting in

injury to persons and/or damage to property.

CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of

used batteries according to national regulations.

For more information on the transmitter, go to www.horizonhobby.com and click

on the support tab for the Spektrum STX2 to download the instruction manual.

TRANSMITTER CONTROLS

1. Steering Wheel Controls direction (left/right) of the model

2. Throttle Trigger Controls speed and direction (forward/brake/reverse) of the model

3. ON/OFF Switch Turns the power ON/OFF

4. Throttle Limiting Switch Adjusts the throttle limit from 50%, 75%, and 100%

5. TH Rate Adjusts the end point of the throttle

6. TH Trim Adjusts the throttle neutral point

7. TH REV Reverses the function of the speed control when pulled back or pushed forward

8. ST REV Reverses the function of the steering when the wheel is turned left or right

9. ST Trim Adjusts the steering center point

10. ST Rate Adjusts the end point of the steering

11. Antenna Transmits the signal to the model

12. Indicator Lights

• Solid red lights—Indicates radio connectivity and adequate battery power

• Flashing red lights—Indicates the battery voltage is critically low. Replace batteries

2.4GHZ DIGITAL

RADIO SYSTEM

1. Ensure the ESC is powered OFF.

2. Remove the vehicle body.

3. Connect the battery to the ESC noting the correct polarity.

4. Install the fully charged battery in the vehicle.

5. Secure the battery to the battery tray with hook and loop straps.

6. Power ON the transmitter, then the vehicle.

NIGHT CRAWLER SE RTR: 1:10 4WD ROCK CRAWLER • INSTRUCTION MANUAL

BINDING

NIGHT CRAWLER SE RTR: 1:10 4WD ROCK CRAWLER • INSTRUCTION MANUAL

DRIVING PRECAUTIONS

• Maintain sight of the vehicle at all times.

• Routinely inspect the vehicle for loose wheel hardware.

• Routinely inspect the steering assembly for any loose hardware. Driving the vehicle

off-road can cause fasteners to loosen over time.

• Do not drive the vehicle in tall grass. Doing so can damage the vehicle or electronics.

• Stop driving the vehicle when you notice a lack of power. Driving the vehicle when

the battery is discharged can cause the receiver to power off. If the receiver loses power,

you will lose control of the vehicle. Damage due to an over-discharged Li-Po battery is

not covered under warranty.

CAUTION: Do not discharge a Li-Po battery below 3V per cell. Batteries discharged

to a voltage lower than the lowest approved voltage may become damaged, result-

ing in loss of performance and potential ﬁre when batteries are charged.

• Do not apply forward or reverse throttle if the vehicle is stuck.

Applying throttle in this instance can damage the motor or ESC.

• After driving the vehicle, allow the electronics to cool before driving the vehicle again.

IMPORTANT: Keep wires away from all moving parts.

POWERING ON THE VEHICLE

1. Center the ST TRIM and TH TRIM dials on the transmitter.

2. Power on the transmitter.

3. Install a fully charged battery pack per the

Installing the Battery

section.

4. Power on the ESC.

IMPORTANT: The vehicle MUST remain on a ﬂat, level surface and motionless

for at least 5 seconds.

BEFORE RUNNING YOUR VEHICLE

1. Check for free suspension movement. All suspension arms and steering components

should move freely. Any binds will cause the vehicle to handle poorly.

2. Charge a battery pack. Always charge the battery pack as per the battery and/or

charger manufacturers’ instructions.

3. Set the transmitter steering trim. Follow the instructions to set the steering trim/subtrim

so that the vehicle drives straight with no input to the steering.

4. Perform a Control Direction Test.

RUN TIME

The largest factor in run time is the capacity of the battery pack. A larger mAh rating

increases the amount of run time experienced.

The condition of a battery pack is also an important factor in both run time and speed.

The battery connectors may become hot during driving. Batteries will lose performance

and capacity over time.

Driving the vehicle from a stop to full speed repeatedly will damage the batteries

and electronics over time. Sudden acceleration will also lead to shorter run times.

TO IMPROVE RUN TIMES

• Keep your vehicle clean and well maintained.

• Allow more airﬂow to the ESC and motor.

• Change the gearing to a lower ratio. A lower ratio decreases the operating temperature

of the electronics. Use a smaller pinion gear or larger spur gear to lower the gear ratio.

• Use a battery pack with a higher mAh rating.

• Use the optimum charger to charge battery packs (Visit your local hobby dealer for

more information).

Binding is the process of programming the receiver to recognize the GUID (Globally Unique

Identiﬁer) code of a single speciﬁc transmitter. The STX2

transmitter and SPMSRX200

receiver are bound at the factory. If you need to rebind, follow the instructions below:

1. Insert the Bind Plug in the BIND port of the ESC.

2. Connect a fully charged battery to the ESC.

3. Power on the ESC. The red receiver LED ﬂashes, indicating the receiver is in bind mode.

4. Center the ST TRIM and TH TRIM dials on the transmitter.

5. Turn the Steering Wheel to Full Right. Power ON the transmitter while holding the

Steering Wheel to the Right.

6. Release the Steering Wheel when the receiver LED goes solid.

7. Remove the Bind Plug and store it in a convenient place.

8. Power OFF the ESC to save the settings.

9. Power OFF the transmitter.

You must rebind when:

• When you want different failsafe positions (e.g. when throttle or steering reverse has

been changed).

• Binding the receiver to a different transmitter.

NOTICE: Do not attempt to bind the transmitter and receiver if there are other

compatible transmitters in bind mode within 400 feet. Doing so may result in

unexpected binding.

Ensure proper ESC function by calibrating the ESC to your transmitter inputs.

1. Power OFF the ESC.

2. Ensure your transmitter is powered ON, the throttle is not reversed, the TR TRIM is neutral

and the throttle travel range is at 100%.

Disable any special functions such as ABS, etc.

3. Keep the throttle at neutral and power ON the ESC. The ESC automatically calibrates the

throttle range after 3 seconds.

4. One long beep will sound when the ESC is ready to run.

ESC CALIBRATION

NIGHT CRAWLER SE RTR: 1:10 4WD ROCK CRAWLER • INSTRUCTION MANUAL

PERFORMING A CONTROL DIRECTION TEST

Perform a control test with the vehicle wheels off the ground. If the wheels rotate after the

vehicle is powered ON, adjust the TH Trim knob until they stop. To make the wheels move

forward, pull the trigger. To reverse them, wait for the wheels to stop, then push the trigger.

When moving forward, the wheels should maintain a straight line without any steering wheel

input. If not, adjust the ST Trim knob, so the wheels maintain a straight line without having to

turn the steering wheel.

SPECIFICATIONS

Type Brushed

Constant/Peak 60A/360A

Resistance 0.0008 Ohms

Function

Forward/Brake/Reverse, Forward/Brake, Forward/Reverse

(Crawler Mode)

Vehicle Type 1/10 on-road and off-road; 1/10 rock crawler

Operation

Proportional forward, proportional reverse with braking

delay, Crawler Mode

Battery Type/Input Voltage 2–3 cell Li-Po/Li-Fe; 5–7 cell Ni-MH/Ni-Cd

Motor Type

540-/550-size closed endbell motors: 2S Li-Po down to

12T; 3S Li-Po down to 35T

BEC Output 6V/3A

Overload Protection Thermal

Dimensions 35.6mm x 34mm x 18mm (1.40 in x 1.34 in x 0.71 in)

Weight 40 g (1.41 oz) with wires

Battery Connector EC3

™

connector

Motor Connector 3.5mm Tamiya-style bullet

ESC LED STATUS

• No ESC LEDs will glow when there is no throttle input from the transmitter.

• The red ESC LED glows when there is any throttle input from the transmitter.

AUDIBLE WARNING TONES

1. Input Voltage: The ESC checks the in put voltage when it is powered ON. If a voltage

problem is detected, the ESC continuously sounds 2 beeps with a 1 second pause

(xx-xx-xx). Power OFF the ESC and ensure the connections are secure and that

the battery power is not too low for safe operation.

2. Radio Connection: The ESC checks radio signal input when it is powered ON.

If a problem is detected, the ESC continuously sounds 1 beep with a 2 second pause

(x--x--x). Power OFF the ESC and ensure the radio system is operating correctly.

ESC CALIBRATION PROCEDURE

Ensure proper ESC function by calibrating the ESC to your transmitter inputs.

1. Power OFF the ESC.

2. Ensure your transmitter is powered ON, the throttle is not reversed, the throttle trim is neutral

and the throttle travel range is at 100%. Disable any special functions such as ABS, etc.

3. Keep the throttle at neutral and power ON the ESC.

4. The ESC automatically calibrates the throttle range after 3 seconds.

One long beep will sound when the ESC is ready to run.

CONNECTING THE ESC

1. Connect the RED (+) ESC wire to the RED (+) motor wire.

2. Connect the BLACK (–) ESC wire to the BLACK (–) motor wire.

NOTICE: Always disconnect the battery from the ESC when you have ﬁnished operating

your vehicle. The ESC’s switch only controls power to the receiver and servos. The ESC will

continue to draw current when connected to the battery, resulting in possible damage to

the battery through over discharge.

PROGRAMMING

The ESC comes with two jumpers pre-installed in the MODE: F/B (forward/brake) and BATT:

Li-Po conﬁgurations.

To change the mode to F/B/R (forward/brake/reverse) or F/R (forward/reverse) or change the

battery type to Ni-MH.

1. Power OFF the ESC.

2. Disconnect the jumper from the default port and connect it to the desired port.

3. Power ON the ESC.

If the jumpers are lost or not installed, the ESC will default to MODE: F/B/R and BATT: Li-Po.

WARNING: Do

not connect bind plugs or receiver servo leads into the ESC

programming port. Doing so may damge the ESC and/or components

DYNAMITE

60A WATERPROOF FWD/REV BRUSHED ESC (DYNS2210)

Mode

Forward/Brake/

Reverse

(F/B/R)

Forward/Brake

(F/B)

Forward/

Reverse

(F/R [Crawler

Mode])

Battery (BATT)

Li-Po Ni-MH

Plug the Rock Lights on the vehicle into the AUX CH on the receiver.

Plug the Cage LEDs into the BIND port on the receiver.

Rock LEDs

Cage LEDs

VEHICLE LEDs

NIGHT CRAWLER SE RTR: 1:10 4WD ROCK CRAWLER • INSTRUCTION MANUAL

PRECAUTIONS

• Never touch moving parts.

• Never disassemble while the batteries are installed.

• Always let parts cool before touching.

GEARING

Your vehicle has been equipped with the optimal gearing for the stock platform. It offers an

ideal balance between speed, power and efﬁciency. Should you decide to customize your

vehicle with optional batteries or motors, it may be necessary for you to change the pinion or

spur gear.

Installing a pinion gear with fewer teeth or a spur gear with more teeth will provide greater

torque but will reduce top speed. Likewise, a pinion gear with more teeth or a spur gear with

fewer teeth will reduce torque and increase top speed. Care should be taken when installing

larger pinion gears as this can “overgear” the vehicle, resulting in overheating of the motor

and ESC. When testing different gearing options, pay close attention to the temperature of

the motor and speed control to ensure you are operating within the temperature range of the

components. The motor or ESC should never be so hot that it cannot be touched. If tempera-

tures are too hot, a different gearing combination with a lower pinion gear and/or higher spur

gear is suggested

CHANGING THE PINION GEAR/GEAR RATIO

The following instructions are for replacing a worn pinion gear. If you are changing the pinion

gear size please refer to “Setting the Gear Mesh.”

1. Loosen the pinion gear set screw to remove the installed pinion gear.

2. Loosen the motor screws and slide the motor back.

3. Place the new pinion on the end of the motor shaft so the set screw is located over the

ﬂat area on the shaft.

4. Position the teeth on the pinion gear so they line up with the spur gear and secure the

pinion gear onto the motor shaft by tightening the set screw.

DYNAMITE

540 BRUSHED MOTOR 35T (DYNS1216)

SETTING THE GEAR MESH

The gear mesh has already been set at the factory. Setting it is only necessary when changing

motors or gears.

Proper gear mesh (how gear teeth meet) is important to the performance of the vehicle. When

the gear mesh is too loose, the spur gear could be damaged by the pinion gear on the motor.

If the mesh is too tight, speed could be limited and the motor and ESC will overheat.

1. Loosen the motor screws and slide the motor back.

2. Put a small piece of paper between the pinion and spur gears.

3. Push the gears together with moderate pressure and hold in place while tightening the

motor screws.

4. Remove the paper. Check the mesh at 3–5 different locations around the spur gear for

minimal movement.

TROUBLESHOOTING GUIDE

PROBLEM POSSIBLE CAUSE SOLUTION

Vehicle does not operate

Battery not charged or plugged in Charge battery/plug in

ESC switch not “On” Turn on ESC switch

Transmitter not “On” or low battery Turn on/replace batteries

Motor runs but wheels

do not rotate

Pinion not meshing with spur gear Adjust pinion/spur mesh

Pinion spinning on motor shaft Tighten pinion gear setscrew on motor shaft ﬂat spot

Transmission gears stripped Replace transmission gears

Drive pin broken Check and replace drive pin

Steering does not work

Servo plug not in receiver properly Make sure the steering servo plug is connected to the receiver steering channel, noting proper polarity

Servo gears or motor damaged Replace or repair servo

Will not turn one direction Servo gears damaged Replace or repair servo

Motor does not run

Motor wire solder joint is damaged Resolder the motor wire with the proper equipment

Motor wire broken Repair or replace as needed

ESC damaged Contact Horizon Hobby Product Support

ESC gets hot

Motor over-geared Use smaller pinion or larger spur gear

Driveline bound up Check wheels and transmission for binding

Poor run time and/or sluggish

acceleration

Battery pack not fully charged Recharge battery

Charger not allowing full charge Try another charger

Driveline bound up Check wheels, transmission for binding

Poor range and/or glitching

Transmitter batteries low Check and replace

Vehicle battery low Recharge battery

Loose plugs or wires Check all wire connections and plugs

LIMITED WARRANTY

What this Warranty Covers

Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the

“Product”) will be free from defects in materials and workmanship at the date of purchase.

What is Not Covered

This warranty is not transferable and does not cover (i) cosmetic damage, (ii) damage due

to acts of God, accident, misuse, abuse, negligence, commercial use, or due to improper use,

installation, operation or maintenance, (iii) modiﬁcation of or to any part of the Product, (iv)

attempted service by anyone other than a Horizon Hobby authorized service center, (v) Product

not purchased from an authorized Horizon dealer, or (vi) Product not compliant with applicable

technical regulations or (vii) use that violates any applicable laws, rules, or regulations.

OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY

OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES,

INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE PURCHASER

ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY

MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.

Purchaser’s Remedy

Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be that Horizon

will, at its option, either (i) service, or (ii) replace, any Product determined by Horizon to be

defective. Horizon reserves the right to inspect any and all Product(s) involved in a warranty

claim. Service or replacement decisions are at the sole discretion of Horizon. Proof of purchase

is required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS

WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.

NIGHT CRAWLER SE RTR: 1:10 4WD ROCK CRAWLER • INSTRUCTION MANUAL

20 cm

NIGHT CRAWLER SE RTR: 1:10 4WD ROCK CRAWLER • INSTRUCTION MANUAL

Country of Purchase Horizon Hobby Contact Information Address

United States of America

Horizon Service Center

(Repairs and Repair Requests)

servicecenter.horizonhobby.com/RequestForm/

4105 Fieldstone Rd.

Champaign, Illinois 61822 USA

Horizon Product Support

(Product Technical Assistance)

productsupport@horizonhobby.com

877-504-0233

Sales

websales@horizonhobby.com

800-338-4639

European Union

Horizon Technischer Service

service@horizonhobby.eu

+49 (0) 4121 2655 100

Hanskampring 9

D 22885 Barsbüttel, Germany

Sales: Horizon Hobby GmbH

WARRANTY AND SERVICE CONTACT INFORMATION

FCC STATEMENT

FCC ID: 2AI3D-SS0001

This equipment has been tested and found to comply with the limits for Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment to an outlet on a circuit different from that to which the receiver is

connected.

This device complies with part 15 of the FCC rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

NOTICE: Modiﬁcations to this product will void the user’s authority to operate this

equipment.

RF Radiation Exposure Statement

1. This Transmitter must not be co-located or operating in conjunction with any other

antenna or transmitter.

2. This equipment complies with FCC RF radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated with a

minimum distance of 20 centimeters between the radiator and your body.

Antenna Separation Distance

When operating your Spektrum transmitter, please be sure to maintain

a separation distance of at least 20 cm between your body (excluding

ﬁngers, hands, wrists, ankles and feet) and the antenna to meet RF

exposure safety requirements as determined by FCC regulations.

The illustration shows the approximate 20 cm RF exposure area and

typical hand placement when operating your Spektrum transmitter.

IC INFORMATION

IC: 21682-SSTC9202

This device complies with Industry Canada licence-exempt RSS standard(s). Operation

is subject to the following two conditions: (1) this device may not cause interference,

and (2) this device must accept any interference, including interference that may cause

undesired operation of the device.

EU Compliance Statement: Horizon Hobby, LLC hereby declares that this

product is in compliance with the essential requirements and other relevant

provisions of the RED and EMC Directive.

A copy of the EU Declaration of Conformity is available online at:

http://www.horizonhobby.com/content/support-render-compliance.

Instructions for disposal of WEEE by users in the

European Union

This product must not be disposed of with other waste. Instead, it is the user’s

responsibility to dispose of their waste equipment by handing it over to a

designated collections point for the recycling of waste electrical and electronic

equipment. The separate collection and recycling of your waste equipment at the

time of disposal will help to conserve natural resources and ensure that it is recycled in a manner

that protects human health and the environment. For more information about where you can drop

off your waste equipment for recycling, please contact your local city ofﬁce, your household waste

disposal service or where you purchased the product.

Limitation of Liability

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL

DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY,

REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, TORT,

NEGLIGENCE, STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS

BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the liability

of Horizon exceed the individual price of the Product on which liability is asserted. As Horizon

has no control over use, setup, ﬁnal assembly, modiﬁcation or misuse, no liability shall be

assumed nor accepted for any resulting damage or injury. By the act of use, setup or assembly,

the user accepts all resulting liability. If you as the purchaser or user are not prepared to

accept the liability associated with the use of the Product, purchaser is advised to return the

Product immediately in new and unused condition to the place of purchase.

Law

These terms are governed by Illinois law (without regard to conﬂict of law principals). This

warranty gives you speciﬁc legal rights, and you may also have other rights which vary from state

to state. Horizon reserves the right to change or modify this warranty at any time without notice.

WARRANTY SERVICES

Questions, Assistance, and Services

Your local hobby store and/or place of purchase cannot provide warranty support or service.

Once assembly, setup or use of the Product has been started, you must contact your local

distributor or Horizon directly. This will enable Horizon to better answer your questions and

service you in the event that you may need any assistance. For questions or assistance, please

visit our website at www.horizonhobby.com, submit a Product Support Inquiry, or call the toll

free telephone number referenced in the Warranty and Service Contact Information section to

speak with a Product Support representative.

Inspection or Services

If this Product needs to be inspected or serviced and is compliant in the country you live

and use the Product in, please use the Horizon Online Service Request submission process

found on our website or call Horizon to obtain a Return Merchandise Authorization (RMA)

number. Pack the Product securely using a shipping carton. Please note that original boxes

may be included, but are not designed to withstand the rigors of shipping without additional

protection. Ship via a carrier that provides tracking and insurance for lost or damaged parcels,

as Horizon is not responsible for merchandise until it arrives and is accepted at our facility.

An Online Service Request is available at http://www.horizonhobby.com/content/service-

center_render-service-center. If you do not have internet access, please contact Horizon

Product Support to obtain a RMA number along with instructions for submitting your product

for service. When calling Horizon, you will be asked to provide your complete name, street

address, email address and phone number where you can be reached during business hours.

When sending product into Horizon, please include your RMA number, a list of the included

items, and a brief summary of the problem. A copy of your original sales receipt must be

included for warranty consideration. Be sure your name, address, and RMA number are clearly

written on the outside of the shipping carton.

NOTICE: Do not ship Li-Po batteries to Horizon. If you have any issue with a

Li-Po battery, please contact the appropriate Horizon Product Support ofce.

Warranty Requirements

For Warranty consideration, you must include your original sales receipt verifying

the proof-of-purchase date. Provided warranty conditions have been met, your Product

will be serviced or replaced free of charge. Service or replacement decisions are at the sole

discretion of Horizon.

Non-Warranty Service

Should your service not be covered by warranty, service will be completed and

payment will be required without notication or estimate of the expense unless

the expense exceeds 50% of the retail purchase cost. By submitting the item for

service you are agreeing to payment of the service without notiﬁcation. Service estimates are

available upon request. You must include this request with your item submitted for service.

Non-warranty service estimates will be billed a minimum of ½ hour of labor. In addition you

will be billed for return freight. Horizon accepts money orders and cashier’s checks, as well as

Visa, MasterCard, American Express, and Discover cards. By submitting any item to Horizon for

service, you are agreeing to Horizon’s Terms and Conditions found on our website http://www.

horizonhobby.com/content/service-center_render-service-center.

ATTENTION: Horizon service is limited to Product compliant in the country of

use and ownership. If received, a non-compliant Product will not be serviced.

Further, the sender will be responsible for arranging return shipment of the

un-serviced Product, through a carrier of the sender’s choice and at the

sender’s expense. Horizon will hold non-compliant Product for a period of

60 days from notication, after which it will be discarded.

10/15

COMPLIANCE INFORMATION FOR THE EUROPEAN UNION

NIGHT CRAWLER SE RTR: 1:10 4WD ROCK CRAWLER

REPLACEMENT PARTS // TEILELISTE // LISTE DES PIÈCES DE RECHANGE // ELENCO DEI RICAMBI

Part # English Deutsch Français Italiano

DYN3205 4 x 8 Unﬂanged Ball Bearing

4 x 8 ﬂanschloses Kugellager Roulement à billes sans collet 4 x 8 4 x 8 cuscinetti a sfera senza ﬂangia

DYNS1216 Dynamite 35T 540 Brushed Motor Dynamite 35T 540 Bürstenmotor Moteur à balais Dynamite 35T 540 Motore a spazzole Dynamite 35T 540

DYNS2210 WP 60A FWD/REV Brushed ESC WP 60A FWD/REV Bürstengeschwindigkeitsregler Variateur ESC à balais AV/AR WP 60A WP 60A FWD/REV Brushed ESC

LOS230005 LED Light Board and Housing LED-Leuchtplatine und Gehäuse Panneau et boîtier à DEL

Scheda luci LED e alloggiamento

LOS230047 Roll Cage Set Überrollkäﬁg-Set Ensemble de cage de retournement Set scocca di sicurezza

LOS230048 Accessory Pack Zubehörpaket Pack d’accessoires Pacchetto accessori

LOS230049 3-Way Splitter 3fach-Splitter Diviseur à trois voies Splitter a 3 vie

LOS230050 Body Set w/Drivers, Clear Karosseriesatz mit Fahrern, farblos

Ensemble carrosserie avec outils d’assemblage,

transparent

Set carrozzeria con piloti, trasparente

LOS231004 Side Plate Set, Chassis, Black Seitenplattensatz, Karosserie, Schwarz Ensemble de plaques latérales, châssis, noir Set lamiera laterale, telaio, nero

LOS233000 2.5" Spring 3.4 Rate, Black (4) 2,5" Feder 3,4 Federrate, Schwarz (4) Ressort de 2,5 po, raideur 3,4, noir (4) Molla 2,5", grado 3,4, nero (4)

LOS234001 1.2" Shock Body, Silver (4) 1,2" Dämpfer, Silber (4) Corps d’amortisseur de 1,2 po, argent (4) Corpo ammortizzatore 1,2", argento (4)

LOS235003 M3 x 6mm Cap Head Screws (10) M3 x 6mm Inbusschraube (10) Vis d’assemblage creuses M3 x 6 mm (10) Viti a testa tonda M3 x 6 (10)

LOS4120 48 Pitch Pinion Gear, 20T 48 Pitchzahnradgetriebe, 20T Engrenage à pignons pas 48, 20T Pignone 20T, pitch 48

LOSA1030 Spindle and Carrier Set Spindel- und Trägersatz Ensemble axe et support Set fuselli e portafuselli

LOSA1033 Upper Suspension Link Mount Obere Aufhängungsarm der Halterung Support pour bras de suspension supérieur Supporto braccetto sospensione superiore

LOSA1034 Lower Suspension Link, Mounts and Pin Obere Unterfederungsarm, Halterung und Stift Bras de suspension inférieur, supports et broche Supporti braccetto sospensione inferiori e perno

LOSA1517 Steering King Pins and Hardware Steuerung Königszapfen und Hardware Pivots de fusée et matériel King pin sterzo e bulloneria

LOSA2030 Rear Outer Hub, Cap and Hardware Heckaußennabe, Kappe und Hardware Moyeu extérieur arrière, cache et matériel Mozzo esterno posteriore, coperchio e bulloneria

LOSA3184 Rear Axle Hinterachse Essieu arrière Assale posteriore

LOSA3185 Rear Axle Spacer Set, Aluminium Hinterachse Distanzstücksatz, Aluminium Ensemble d’entretoises pour essieu arrière, alum. Set distanziale assale posteriore, alluminio

LOSA3187 HD Worm Gear Set, 21T (2) HD Schneckengetriebesatz, 21T (2) Engrenage à vis sans ﬁn, ultra-résistant, 21T (2) Set vite senza ﬁne HD, 21T (2)

LOSA3194 Front & Center CV Rebuild Kit Front & Mitte-CV Umbau Kit Kit de réparation homocinétique avant et centre Kit ricostruzione CV anteriore e posteriore

LOSA3196 Front CV Drive Shaft Set, HD Front CV Antriebswelle Satz, HD

Jeu d’arbres de transmission avant

homocinétiques, ultra-résistant

Set albero di trasmissione CV anteriore, HD

LOSA3197 Front CV Axle HD Front CV Achse HD Essieu avant homocinétique, ultra-résistant

Assale CV anteriore, HD

LOSA3198 Front CV Drive Shaft HD Front CV Antriebswelle, HD

Arbre de transmission homocinétique avant,

ultra-résistant

Albero di trasmissione CV anteriore, HD

LOSA3199 CV Pin Retainer Clip 11mm Pins CV Befestigungsklemme 11mm Pins

Bague de retenue avec axes homocinétiques,

axes de 11 mm

Morsetto di fermo perno CV, perni 11 mm

LOSA4009 Battery Straps, Hook/Loop (2) Akkuklemmen, Haken/Schlaufen (2) Sangles de batterie, velcro (2) Fascette a strappo batteria (2)

LOSA4012 Front/Rear Axle Case Set Front/Hinterachse-Gehäusesatz Jeu de carters d’essieu avant/arrière Set scatola assale anteriore/posteriore

LOSA4036 ESC Platform Geschwindigkeitsregler-Plattform Plateforme ESC Piattaforma ESC

LOSA4037 Servo Mnts, Plate and Hardware Servo-Halterung, Platte und Hardware Supports, plaque et matériel pour servo Supporti servo, piastra e bulloneria

LOSA4039 Transmission Skid Plate: CCR Getriebe Gleitbrett: CCR Plaque de protection pour transmission : CCR Piastra proteggi trasmissione: CCR

LOSA5012

Upper Shock Bushings and

Lower Shock Pivot Ball (4)

Obere Dämpferlager und untere

Dämpferschwenkkugel (4)

Bagues supérieures d’amortisseur et Rotule

inférieure d’amortisseur (4)

Boccole ammortizzatore superiori e articolazione

a rotula ammortizzatore inferiore (4)

LOSA5015 Double O-Ring Shock Cartridge Doppel-O-Ring Stoßdämpfer Cartouche d’amortisseur à double joint torique Doppio O-Ring cartucce ammortizzatore

LOSA5023 Shock Spring Clamps & Cups Stoßdämpfer-Federspanner & Federteller Brides et coupelles de ressort d’amortisseur Morsetti e coppe molle ammortizzatori

LOSA5062 Shock Shaft,1.2" Ti-Nitride Kolbenstange,1.2" Ti-Nitrid Arbre d’amortisseur, 1,2 po, nitrure de titane Stelo ammortizzatore, 1.2" Ti-Nitride

LOSA5079 Shock Ends and Cups (4) Stoßdämpferenden und Teller (4) Embouts et coupelles d'amortisseur (4) Terminali e coppe ammortizzatori (4)

LOSA6045 HD Steering Link Set HD Lenkgliedset Timonerie de direction, ultra-résistante Set braccetti sterzo HD

LOSA6100 1/8" E-Clips 1/8“ E-Klemmen Clips en e, 3 mm (1/8 po) E-Clip, 1/8"

LOSA6109 E-Clips, 5mm (12) E-Klemmen, 5mm (12) Clips en e, 5 mm (12) E-Clip, 5 mm (12)

LOSA6201 3mm x 6mm Socket Head Screw 3mm x 6mm Innensechskantschraube Vis à pans creux 3 mm x 6 mm Vite a brugola 3 x 6 mm

LOSA6206 4-40 x 3/8" Socket Head Screws (10) 4-40 x 3/8 Innensechskantschrauben (10) Vis à 6 pans creux 4-40 x 3/8 po (10) Viti a brugola 4-40 x 3/8" (10)

LOSA6210 4-40 x 3/8" Flat Head Socket 4-40 x 3/8 Flachkopfbuchse Vis à tête fraisée à 6 pans creux 4-40 x 3/8 po Vite a testa piatta 4-40 x 3/8"

LOSA6213 4-40 x 1/4" Flat Socket Screw (6) 4-40 x 1/4 Flachkopf-Zylinderschraube (6) Vis à tête fraisée à 6 pans creux 4-40 x 1/4 po (6) Viti a testa piatta 4-40 x 1/4" (6)

LOSA6221 4-40 x 5/8" Cap Screws (6) 4-40 x 5/8 Kopfschrauben (6) Vis d’assemblage 4-40 x 5/8 po (6) Viti a brugola 4-40 x 5/8" (6)

LOSA6228 5-40 x 1/8" Hardened Setscrews (10)

5-40 x 1/8 Gehärtete Feststellschrauben (10)

Vis de ﬁxation en acier trempé 5-40 x 1/8 po (10) Viti di arresto indurite 5-40 x 1/8" (10)

LOSA6229 4-40 x 3/8" Button Head Screws 4-40 x 3/8 Rundkopfschrauben Vis à tête bombée 4-40 x 3/8 po Viti a testa tonda 4-40 x 3/8"

LOSA6245 4-40 x 5/16" Button Head Screws (10) 4-40 x 5/16 Rundkopfschrauben (10) Vis à tête bombée 4-40 x 5/16 po (10) Viti a testa tonda 4-40 x 5/16" (10)

LOSA6248 4-40 Setscrew Assortment (11) 4-40 Feststellschrauben-Set (11) Assortiment de vis de ﬁxation 4-40 (11) Viti di arresto assortite 4-40 (11)

LOSA6256 4-40 x 1/2 Button Head Cap Screw (6) 4-40 x 1/2 Halbrundschraube (6) Vis d’assemblage à tête bombée 4-40 x 1/2 po (6) Vite a testa tonda 4-40 x 1/2 (6)

LOSA6258 2-56 x 5/16" Flathead Screws (24) 2-56 x 5/16 Flachkopfschrauben (24) Vis à tête plate 2-56 x 5/16 po (24) Viti a testa piatta 2-56 x 5/16" (24)

LOSA6269 4-40 x 5/16" Flathead Screw (6) 4-40 x 5/16 Flachkopfschraube (6) Vis à tête plate 4-40 x 5/16 po (6) Vite a testa piatta 4-40 x 5/16" (6)

LOSA6294 2-56 x 5/16" Cap Screw (6) 2-56 x 5/16 Kopfschraube (6) Vis d’assemblage 2-56 x 5/16 po (6) Vite a brugola 2-56 x 5/16" (6)

LOSA6306 4-40 Aluminum Mini-Nuts (10) 4-40 Aluminum Minimuttern (10) Mini-écrous en aluminium 4-40 (10) Mini dadi in alluminio 4-40 (10)

LOSA6308 4-40 Steel Locking 1/2 Nuts (10) 4-40 Stahlsicherung 1/2-Mutter (10) Demi-écrous de blocage en acier 4-40 (10)

Dadi autobloccanti 4-40 1/2" (10)

LOSA6350 #4 and 1/8" Hardened Washers #4 und 1/8 gehärtete Unterlegscheiben Rondelles en acier trempé no4 et 1/8 po Rondelle indurite #4 e 1/8"

LOSA6358 Shim Set Dichtscheibe-Satz Jeu de cales Set spessori

NIGHT CRAWLER SE RTR: 1:10 4WD ROCK CRAWLER

REPLACEMENT PARTS // TEILELISTE // LISTE DES PIÈCES DE RECHANGE // ELENCO DEI RICAMBI

Part # English Deutsch Français Italiano

LOSA6937 5 x 10mm Shielded Ball Bearing (2) 5 x 10mm abgedichtetes Kugellager (2) Roulement à billes blindé 5 x 10 mm (2) Cuscinetti a sfera schermati 5 x 10 mm (2)

LOSA6940 6 x 12mm Sealed Ball Bearing (4) 6 x 12mm abgedichtetes Kugellager (4) Roulement à billes hermétique 6 x 12 mm (4) Cuscinetti a sfera sigillati 6 x 12 mm (4)

LOSA6947

5 x 11 x 4mm Rubber Sealed

Ball Bearing (4)

5 x 11 x 4 mm gummiversiegeltes

Kugellager (4)

Roulement à billes hermétique en caoutchouc

5 x 11 x 4 mm (4)

Cuscinetti a sfera sigillati in gomma

5 x 11 x 4 mm (4)

LOSA6956 12 x 18 x 4mm Ball Bearing (2) 12 x 18 x 4 mm Kugellager (2) Roulement à billes 12 x 18 x 4 mm (2) Cuscinetti a sfera 12 x 18 x 4 mm (2)

LOSB2034 Lower Track Rods Untere Spurstangen Barres d’accouplement inférieures Tiranti inferiori

LOSB2036 Steering Track Rod & Bushings Lenkspurstange & Buchsen Biellette de direction et bagues Tiranti sterzo e boccole

LOSB2037 Upper Track Rods Obere Spurstangen Barres d’accouplement supérieures Tiranti superiori

LOSB2291 Battery Tray Akkuhalterung Support de batterie Vassoio portabatteria

LOSB2370 Servo Arm & Metal Insert Servoarm & Metalleinsatz Bras de servo et tubulure métallique Squadretta servo e inserto di metallo

LOSB3012 Center Tranny Case and Supports Zentrales Getriebegehäuse und Stützen Carter de boîte de vitesses centrale et supports Scatola e supporti trasmissione centrale

LOSB3013 Center Transmission Gear Set Zentrales Übersetzungsgetriebe-Set Ensemble boîte de transmission centrale Set ingranaggio trasmissione centrale

LOSB3014 Center Transmission Shaft/Pin Set Zentrale Getriebewelle/Stift-Satz Ensemble arbre/tige de transmission centrale Set albero/perno trasmissione centrale

LOSB3018 Motor Plate, Black Motorplatte, Schwarz Plaque moteur, noir Piastra motore, nero

LOSB3525 12mm Molded Hex Pins and Lock Nuts (4)

12mm gegossene Sechskantstifte und

Sicherungsmuttern (4)

Tiges hexagonales moulées de 12 mm et

contre-écrous (4)

Perni esagonali e controdadi stampati 12 mm (4)

LOSB3580 Center CV Drive Shaft Zentrale CV-Antriebswelle Arbre de transmission homocinétique central Albero di trasmissione centrale CV

LOSB3581 Center Drive Shaft Cup Adapter Zentrale Antriebswelle Telleradapter Adaptateur coupelle d‘arbre de transmission central Adattatore coppa albero di trasmissione centrale

LOSB3582

Center Drive Shaft CV Yoke, Coupler,

Hardware

Zentrales Antriebswelle, CV-Bügel,

Kupplung, Hardware

Chape, coupleur, matériel pour arbre

de transmission homocinétique central

Yoke, accoppiatore e bulloneria albero

di trasmissione centrale CV

LOSB3583 Center CV Drive Shaft Set Zentrale CV-Antriebswelle-Satz Ensemble arbre de transmission homocinétique central Set albero di trasmissione centrale CV

LOSB9996 LED Light Set LED-Licht-Satz Ensemble d’éclairage DEL Set luci LED

SPMSRX200 SRX200 2-CH 2.4 GHz FHSS RX SRX200 2-CH 2,4 GHz FHSS RX Récepteur FHSS 2,4 GHz 2 canaux SRX200 SRX200 2-CH 2,4 GHz FHSS RX

SPMSTX200 STX2 2-CH 2.4 GHz FHSS Radio System STX2 2-CH 2,4 GHz FHSS Funksystem Système radio FHSS 2,4 GHz 2 canaux SRX2 Sistema radio STX2 2-CH 2,4 GHz FHSS

TLR5902 M3 x 8mm Button Head Screws (10) M3 x 8 mm Rundkopfschrauben (10) Vis à tête bombée M3 x 8 mm (10) Viti a testa tonda M3 x 8 mm (10)

TLR5913 M2.5 x 12mm Button Head Screws (10) M2,5 x 12mm Rundkopfschrauben (10) Vis à tête bombée M2.5 x 12 mm (10) Viti a testa tonda M2,5 x 12 mm (10)

TLR6312 M2.5 x .45 x 5mm Locknut (6) M2,5 x 0,45 x 5mm Kontermutter (6) Contre-écrou M2,5 x 0,45 x 5 mm (6) Controdadi M2,5 x 45 x 5 mm (6)

TLR6352 M3 Washers (10) M3 Unterlegscheiben (10) Rondelles M3 (10) Rondelle M3 (10)

TLR8202 Body Clips, Black (12) Gehäuseklemmen, schwarz (12) Clips de carrosserie, noir (12) Clip carrozzeria, colore nero (12)

TLR255001 M2.5 x 5mm Button Head Screws (10) M2,5 x 5mm Rundkopfschrauben (10) Vis à tête bombée M2,5 x 5 mm (10) Viti a testa tonda M2,5 x 5 mm (10)

TLR336000

4mm Aluminium Serrated Lock Nuts,

Black (6)

4mm Aluminium-Rändelmutter, Schwarz (6)

Contre-écrous en aluminium à embase striée

4 mm, noir (6)

Controdado dentato in allumino 4 mm, nero (6)

TLR235008 M3 x 6mm Flat Head Screws (10) M3 x 6mm Flachkopfschrauben (10) Vis à tête plate M3 x 6 mm (10) Viti a testa piatta M3 x 6 (10)

TLR74006 Silicone Shock Oil, 30 wt, 2 oz Stoßdämpfer-Silikonöl, 30 wt, 2 oz Huile de silicone pour amortisseur, 30WT, 2oz Olio di silicone ammortizzatore, 30 wt, 2 oz

VTR43000 Beadlock Wheel with Rings (2) Beadlock-Rad mit Ringen (2) Roue à verrou de talon avec bagues (2) Cerchioni Beadlock con anelli (2)

VTR43018 TSL SX Swamper 1.9 Tire w/Insert TSL SX Swamper 1,9 Reifen mit Einsatz Pneu 1,9 po TSL SX Swamper avec fond Ruota TSL SX Swamper 1,9 con inserto

OPTIONAL PARTS // OPTIONALE TEILE // PIÈCES OPTIONNELLES // PARTI OPZIONALI

Part # English Deutsch Français Italiano

DYNC3000 Ultra 100W AC/DC Touch Charger Ultra 100W AC/DC Touch Ladegerät Chargeur Ultra AC/DC 100W Touch Caricabatterie Ultra AC/DC 100W Touch

DYNT0501 Start Up Tool Set Anfänger-Werkzeugsatz Set d’outils de démarrage Set attrezzi

DYN9005EC 7.4V 5000mAh 2S 30C LiPo, Hardcase: EC3 7,4V 5000mA 30C 2S LiPo, Hartschale: EC3 7,4V 5000mA 30C, boitier rigide avec prise EC3 Batteria LiPo hardcase 7,4V 5000mAh 2S 30C: EC3

DYNB3802EC 7.4V 5000mAh 2S 50C LiPo, Hardcase: EC3 7,4V 5000mA 50C 2S LiPo, Hartschale: EC3 7,4V 5000mA 50C, boitier rigide avec prise EC3 Batteria LiPo hardcase 7,4V 5000mAh 2S 50C: EC3

DYNB3850EC 7.6V HV 4000mAh 2S 50C LiPo Hardcase 7,6V HV 4000mA 50C 2S LiPo, Hartschale: EC3 7,6V 4000mA 50C, boitier rigide avec prise EC3 Batteria LiPo hardcase 7,6V 4000mAh 2S 50C: EC3

DYNB3852EC 7.6V HV 5000mAh 2S 50C LiPo Hardcase: EC3 7,6V 5000mA 50C 2S LiPo, Hartschale: EC3 7,6V 5000mA 50C, boitier rigide avec prise EC3 Batteria LiPo hardcase 7,6V 5000mAh 2S 50C: EC3

LOS43005

2.2 Beadlock Wheels, Chrome with

Red Rings (2)

2,2 Beadlockfelgen chrom und rote ringe (2)

2,2 Jantes Beadlock chrome avec anneaux

rouge (2)

Ruote Beadlock cromo con anelli rosso 2,2 (2)

LOSA3186 12 mm Alumnum 5.7 mm (wide) Hex (4) 12 mm Alumnum 5,7 mm (breit) Hex (4) 12 mm Alumnum 5,7 mm (large) Hex (4) 12 mm Alumnum 5,7 mm (largo) Esagonale (4)

LOSA7682B

Front/Rear Rock Claws 2.2 Tires w/Foam,

Blue (2)

Vorne / Hinten Rock Claws 2.2 Reifen w /

Foam, Blau (2)

Griffes de roche avant / arrière 2,2 Pneus

avec mousse, bleu (2)

Rock Artigli anteriori / posteriori 2,2

Pneumatici w / Foam, Blu (2)

RECOMMENDED PARTS // EMPFOHLENE TEILE // PIÈCES RECOMMANDÉES //

PEZZI CONSIGLIATI

Part # English Deutsch Français Italiano

DYN1070EC Speedpack 7.2V 3300mAh NiMH 6C Flat: EC3 Speedpack 7,2V 3300mAh NiMH 6C Flach: EC3

Batterie plate NiMH 6C 7,2 V 3300 mAh

Speedpack : EC3

Speedpack 7,2 V 3300 mAh NiMH 6C Flat:

EC3

DYN9004EC 7.4V 5000mAh 2S 20C LiPo, Hardcase: EC3

7,4V 5000mA 20C 2S LiPo, Hartschale: EC3 7,4V 5000mA 20C, boitier rigide avec prise EC3

7,4V 5000 mAh 2S 20C LiPo, Hardcase: EC3

DYNC2000CA Prophet Sport NiMH 35W AC Charger Prophet Sport NiMH 35 W AC-Ladegerät Chargeur CA NiMH 35W Prophet Caricabatterie Prophet Sport NiMH 35W AC

DYNC2005CA Prophet Sport LiPo 35W AC Charger Prophet Sport LiPo 35 W AC-Ladegerät Chargeur CA LiPo 35W Prophet Sport Caricabatterie Prophet Sport LiPo 35W AC

DYNC2010CA Prophet Sport Plus 50W AC/DC Charger

Prophet Sport Plus 50 W Wechsel-/Gleichstrom-

Ladegerät

Chargeur CA/CC 50W Prophet Sport Plus Caricabatterie Prophet Sport Plus 50W AC