Pro Boat PRB08037T1 Le manuel du propriétaire

Marque: Pro Boat

Modèle: PRB08037T1

Catégorie: Jouets télécommandés

Taper: Le manuel du propriétaire

Ce manuel convient également à

PRB08037

3232

INCH BRUSHLESS 6S DEEP V WITH SMARTINCH BRUSHLESS 6S DEEP V WITH SMART

IMPULSE 32IMPULSE 32

Instruction Manual • Bedienungsanleitung • Manuel de l’utilisateur • Manuale dell’utente

Impulse 32-Inch Brushless 6S Deep V

Your new Horizon Hobby boat has been designed and built

with a combination of waterproof and water-resistant compo-

nents to allow you to operate the product in calm, fresh water

conditions.

While the entire boat is highly water-resistant, it is not com-

pletely waterproof and your boat should NOT be treated like

a submarine. The various electronic components used in the

boat, such as the servo(s) and receiver are waterproof, how-

ever, most of the mechanical components are water-resistant

and require additional maintenance after use.

Metal parts, including the bearings, pins, screws and nuts, propel-

ler, rudder, rudder mounts, prop struts, as well as the contacts in

the electrical cables, will be susceptible to corrosion if additional

maintenance is not performed after running in wet conditions.

To maximize the long-term performance of your boat and to

keep the warranty intact, the procedures described in the “Wet

Conditions Maintenance” section must be performed regularly.

CAUTION: Failure to exercise caution while using this

product and complying with the following precautions

could result in product malfunction and/or void the warranty.

Water-Resistant Boat with Waterproof Electronics

As the user of this product, you are solely responsible for

operating in a manner that does not endanger yourself and

others or result in damage to the product or the property of

others.

• When handling and/or transporting your boat, always

pick up the boat from the sides, keeping all moving parts

pointed away from you.

• Always keep a safe distance in all directions around your

model to avoid collisions or injury. This model is controlled

by a radio signal subject to interference from many

sources outside your control. Interference can cause

momentary loss of control.

• Always operate your model in open spaces away from

full-size vehicles, traffic and people.

• Always carefully follow the directions and warnings

for this and any optional support equipment (chargers,

rechargeable battery packs, etc.).

• Always keep all chemicals, small parts and anything

electrical out of the reach of children.

• Always avoid water exposure to all equipment not

specifically designed and protected for this purpose.

Moisture causes damage to unprotected electronics.

• Never place any portion of the model in your mouth as it

could cause serious injury or even death.

• Never operate your model with low transmitter batteries.

NOTICE

MEANING OF SPECIAL LANGUAGE

All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For

up-to-date product literature, visit horizonhobby.com or towerhobbies.com and click on the support or resources tab for this product.

The following terms are used throughout the product literature to indicate various levels of potential harm when operating this

product:

WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious

injury OR create a high probability of superﬁcial injury.

CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of

serious injury.

NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND little or no possibility of

injury.

This is a sophisticated hobby product and NOT a toy. It must be operated with caution and common sense and requires some basic

mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product

or other property. This product is not intended for use by children without direct adult supervision. Do not use with incompatible

components or alter this product in any way outside of the instructions provided by Horizon Hobby, LLC. This manual contains

instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual,

prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.

Age Recommendation: Not for children under 14 years. This is not a toy.

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating.

Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury.

Safety Precautions and Warnings

INSTRUCTION MANUAL

General Precautions

• Read the WET CONDITIONS MAINTENANCE procedures

and make sure that you have all the tools you will need to

properly maintain your boat.

• Not all batteries can be used in wet conditions. Consult the

battery manufacturer before use. Caution should be taken

when using Li-Po batteries in wet conditions.

• Most transmitters are not water-resistant. Consult your

transmitter’s manual or the manufacturer before operation.

• Never operate your transmitter or boat when lightning is

present.

• Salt water is very conductive and highly corrosive. If you

choose to run your boat in salt water, immediately rinse

the boat in fresh water after each use. Operating your boat

in salt water is at the sole discretion of the modeler.

Wet Conditions Maintenance

• Drain any water that has collected in the hull by removing

the drain plug or canopy and tilting the boat in the

appropriate direction to drain the water.

CAUTION: Always keep hands, fingers, tools and any

loose or hanging objects away from rotating parts.

• Remove the battery pack(s) and dry the contacts. If you have

an air compressor or a can of compressed air, blow out any

water that may be inside the recessed connector housings.

• Dry and lubricate parts after every 30 minutes of

operation or if the boat becomes submerged.

NOTICE: Never use a pressure washer to clean your boat.

• Use an air compressor or a can of compressed air to dry

the boat and help remove any water that may have gotten

into small crevices or corners.

• Spray the bearings, fasteners and other metal parts with

a water-displacing light oil or lubricant.

• Let the boat air dry before you store it. Water (and oil)

may continue to drip for a few hours.

Specifications

Length 32.95 in (837mm)

Beam 9.36 in (238 mm)

Transmitter

DX3 SMART DSMR 3 CH

(SPMR2340)

Receiver

SR315 3CH Receiver

(

SPMSR315

)

Hull Material Fiberglass

Motor Firma 2000Kv Brushless Marine Motor

1900Kv

(SPMXMM1100)

ESC

Firma 160A

SMART

Brushless Marine ESC

(

SPMXSE1160M

)

Servo

Waterproof Servo

(

SPMS605

)

Batteries Transmitter: 4 AA batteries

Boat: (2) 11.1V 5000mAh 3S 100C SMART

LiPo, Hardcase, IC5 (SPMX50003S100H5)

(sold separately)

Table of Contents

9.36 in

(238mm)

32.95 in (837mm)

Box Contents .......................................................................... 4

Recommended Tools and Materials ....................................... 4

Battery and Charger (Not Included) ........................................4

Installing the Battery Pack ...................................................... 4

Antenna Tube Installation........................................................ 5

DX3 Smart DSMR Transmitter Functions ............................... 5

Transmitter Battery Installation ............................................... 5

Spektrum SMART Technology ................................................5

Low Voltage Cutoff (LVC) ........................................................6

Getting Started ....................................................................... 6

Control Check ......................................................................... 6

Testing Your Boat in the Water ............................................... 7

Boating Tips ............................................................................7

When You Are Finished .......................................................... 7

Tuning For Optimal Performance ............................................ 8

After Boating and Maintenance ..............................................9

Drivetrain Lubrication..............................................................9

Water Cooling System .......................................................... 10

Rudder Service ..................................................................... 10

Propeller Service .................................................................. 10

Motor Care ........................................................................... 11

Radio and ECS Setup ........................................................... 11

SR315 Receiver .................................................................... 11

Binding .................................................................................. 11

DSMR Bind Process ............................................................. 11

Receiver Antenna ................................................................. 11

ESC and Transmitter Calibration............................................ 12

Programming with the SMART Programmer Box ................ 12

160A Programmable Options ............................................... 12

Troubleshooting Guide .......................................................... 13

Replacement Parts ............................................................... 14

Limited Warranty .................................................................. 14

Recommended Items ........................................................... 14

Optional Items ...................................................................... 14

Warranty and Service Contact Information .......................... 15

FCC Information ................................................................... 16

IC Information ....................................................................... 16

Compliance Information for the European Union ................. 16

Product Inspection

Carefully remove the boat and radio transmitter from the box.

Inspect the boat for damage. If your product is damaged,

please contact the hobby shop where you purchased your

boat, or contact Product Support. Refer to the Warranty and

Service Contact Information section for more info.

Installing the Battery Pack

The Impulse 32 boat requires two 3S hardcase LiPo

Batteries with IC5 connector (not included). The included

Spektrum™ Firma™ SMART ESC (SPMXSE1160M)

has an IC5™ battery connector. We recommend the

Spektrum 5000mAh 3S 11.1V 100C SMART LiPo

Batteries (SPMX50003S100H5). We recommend charging

Spektrum SMART Batteries paired with Spektrum Smart

Chargers because Smart chargers will automatically

configure the charge settings for Smart batteries. We

recommend the Spektrum S2100 SMART AC Charger,

2x100w (SPMXC1010) with IC3 to IC5 charge adapter

(SPMXCA507).

Refer to your battery and charger manuals for usage, safety,

and charging information.

NOTICE: Never charge a battery in the boat or damage may

result.

Battery and Charger (Not Included)

Impulse 32-Inch Brushless 6S Deep V

Recommended Tools and Materials

• Adjustable wrench

• Needle nose pliers

• Paper towel

• Rubbing alcohol

• Phillips screwdriver: #1, #2

• Hex drivers: 1.5mm and 2mm

• Clear tape (DYNM0102)

• Grease Gun (DYNE4200)

1. Loosen the four thumbscrews on the battery hatch

and remove it from the hull.

2. Apply one side of the included hook and loop tape to

battery tray. Apply the other side of the hook and loop

tape to the back of the battery.

3. Install the fully charged batteries fully forward in the

battery compartment and secure them with the hook

and loop straps.

4. Connect the batteries to the ESC.

WARNING: When using two batteries, always make

sure the batteries are of similar type (voltage and

capacity). Connecting batteries of mismatched capacity may

result in battery over discharge, which could result in fire

causing property damage or personal injury.

Box Contents

• Pro Boat

Impulse™ 32 inch Brushless RTR Catamaran

• Spektrum DX3 SMART DSMR

3CH Transmitter (SPMR2340)

• Spektrum SR315 3CH Receiver (SPMSR315)

• Spektrum Firma™ 160A SMART Brushless Marine ESC

(SPMXSE1160M)

• Spektrum 9KG Servo, WP, Metal Cent. Case 23T

(SPSM605)

• Firma 2000Kv Brushless Marine Motor (SPMXMM1100v)

• Four AA Batteries

A/B

A/B.

DX3 Smart DSMR Transmitter Functions

Channel 3 Button

Throttle/Brake

Steering Wheel

Steering Rate

Adjusts the end point of the steering

Brake Rate

Adjusts the braking end point.

Steering Trim

Adjusts the steering center point. Normally,

the steering trim is adjusted until the vehicle

tracks straight.

Throttle Trim

Adjusts the throttle neutral point

SMART Battery Level Indicator

Servo Reversing

To reverse the Throttle (TH) or Steering (ST)

channel, switch the position of the correlating

switch—“N” is for normal, “R” is for reverse.

Throttle Limit

Limits throttle output to 50/75/100%

Select 50% or 75% for less experienced

drivers or when you are driving the vehicle in

a small area.

Power LED

• Solid red lights: Indicates radio

connectivity and adequate battery power

• Flashing red lights: Indicates the battery

voltage is critically low. Replace batteries

Power Button

Bind Button

Spektrum SMART Technology

The Impulse 32 boat includes Spektrum Smart Technology in

the ESC and receiver, which can provide you with telemetry

information like battery voltage from your vehicle. The included

DX3 Smart transmitter features an LED display to show the

battery level of your vehicle during operation.

For additional Smart functionality, consider upgrading to a more

advanced Smart Technology compatible Spektrum transmitter such

as the DX5C (SPMR5100 transmitter only), or DX5 Pro (SPMR5010

transmitter only). Use Spektrum Smart batteries to power your

Impulse 32 boat to take full advantage of Smart Technology, which

can communicate detailed battery data through the system as well.

Visit www.SpektrumRC.com for more information.

Install the receiver antenna in the tube as shown. Do not

bend the end of antenna over the antenna tube and place

the cap over it or damage may result. The antenna does

not have to be outside of the tube to operate properly.

Keep the end of the antenna above the boat’s waterline

to get the best transmitter reception.

NOTICE: Do not cut or kink the receiver antenna or

damage may result.

Antenna Tube Installation

Transmitter Battery Installation

This transmitter requires 4 AA batteries

1. Remove the battery cover from the transmitter.

2. Install the batteries as shown.

3. Install the battery cover.

CAUTION: Never remove the transmitter batteries

while the model is powered ON. Loss of model

control, damage, or injury may occur.

CAUTION: If using rechargeable batteries, charge only

rechargeable batteries. Charging non-rechargeable

batteries may cause the batteries to burst, resulting in injury

to persons and/or damage to property.

CAUTION: Risk of explosion if battery is replaced by

an incorrect type. Dispose of used batteries according

to national regulations.

INSTRUCTION MANUAL

1. Remove the canopy from the hull.

2. Install the receiver antenna in the antenna tube.

3. Install fully charged batteries fully forward in the

compartment and secure them with the hook and

loop straps.

4. Power on the transmitter. Ensure the throttle is

not reversed and the throttle trim is neutral.

5. Connect the batteries to the ESC.

6. Press the ESC power button until the ESC beeps

and lights up.

WARNING: Never use a LiPo battery in NiMH mode.

Using a LiPo in NiMH mode may result in drawing

the battery below a level where the battery is safe to

recharge. In this event, attempting to recharge a LiPo

Battery when the voltage is too low may result in a fire

causing property damage and personal injury.

7. Install the canopy on the hull.

Getting Started

Control Check

IMPORTANT: Perform a control check at the beginning

of each boating session, after repair, or after installation

of new batteries.

Ensure the receiver antenna is extended properly and all

batteries are fully charged.

1. Power ON the transmitter and the boat.

Do not install the battery compartment.

2. Place the boat on a steady surface.

3. Check steering and throttle on the transmitter.

The factory default setting for the LVC in the ESC included with

your boat is set at 3.2V per cell. Discharging a Li-Po battery

below 3V per cell may damage your battery. The included

ESC protects the boat battery from over-discharge using Low

Voltage Cutoff (LVC). Before the battery charge decreases too

much, LVC removes power supplied to the motor.

The boat drastically slows or stops completely once LVC is

activated. Releasing the throttle and reapplying it will provide

a limited amount of power to safely return the boat to shore.

Repeated use after LVC is activated will damage the batteries.

Once LVC has been activated, the ESC status light will flash

red continuously, indicating that the ESC is in LVC mode.

NOTICE: The LVC reserves battery capacity to allow you

to safely return your boat to shore. Continued use after

LVC has activated will damage your battery.

LVC can activate prematurely if you use (1) low C-rated

batteries or (2) old, worn, and/or weak batteries.

The average run time—using the recommended batteries

(

SPMX50003S100H5

)—is between 7–10 minutes at non-stop,

open throttle. Limited run time may indicate worn or weak

batteries.

Tip: If you’ve installed freshly charged batteries, and LVC

activates within the first minute of operation, replace your

worn or weak batteries with the recommended batteries.

Tip: Monitor your boat battery’s voltage before and after

boating by using an XBC100 Smart Battery Checker and

Servo Driver (SPMXBC100), sold separately.

Disconnect and remove the Li-Po battery from the boat after

use to prevent trickle discharge. Charge your Li-Po battery to

half capacity before storage. During storage, make sure the

battery charge does not fall below 3V per cell. LVC does not

prevent the battery from over-discharge during storage.

Low Voltage Cutoff (LVC)

5 642

Impulse 32-Inch Brushless 6S Deep V

When You Are Finished

1. Power off the receiver by pressing the power button

for 2 seconds.

2. Power off the transmitter.

3. Disconnect and remove the battery from the boat.

Maximum speeds can only be achieved when water conditions

are optimal. Avoid sharp turns at high speed and reduce speed

when water and/or wind conditions are not favorable. Strong

wind or waves can capsize the boat when it is moving at high

speeds. Always operate your boat in favorable wind and water

conditions to prevent it from capsizing.

Consult local laws and ordinances before choosing a

location to pilot your boat.

When boating in water, avoid boating near:

• watercraft

• people (swimming areas, fishing areas)

• stationary objects

• waves, wakes

• rapidly moving water

• wildlife

• floating debris

• overhanging trees

• vegetation

Practice driving the boat at low throttle by switching the

transmitter preset throttle limiter to the medium setting.

Advance the throttle setting as you become proficient with

driving.

If you need to retrieve your boat from the water, use fishing

equipment or another boat.

CAUTION: Never operate the boat in extreme

temperatures, windy conditions or turbulent water.

CAUTION: Never attempt to retrieve a downed boat

by swimming to retrieve it.

Boating Tips

1. Carefully place the boat in the water.

2. If the boat does not go straight, adjust the steering trim

dial on the transmitter.

3. Return the boat to shore when it begins to slow or when

LVC activates.

4. Power off the ESC and disconnect the battery.

5. Turn off the transmitter.

NOTICE: Always power OFF the receiver before powering

OFF the transmitter. If the transmitter is powered OFF

before the boat, the receiver will enter failsafe mode.

WARNING: Do not to increase steering throw beyond

the factory setting or servo failure may occur.

Testing Your Boat in the Water

INSTRUCTION MANUAL

Prop Angle Adjustment

• Raising the prop strut increases speed, but also

increases porpoising risk, and increases cavitation. Raise

the prop strut to keep the nose of the boat riding high in

rough water. If the strut is too high the boat will begin

to loose stability and turn precision at higher speeds.

• Lowering the drive strut increases steering stability,

but also increases drag and decreases speed. Lower

the prop strut for smooth water conditions. If the strut

is too low it will increase turn stability and authority,

but will increase drag, and reduce speed.

1. Loosen nut and bolt securing the drive strut on the rear

of the boat.

2. Slide the strut up or down to change the angle of the

propeller in relation to the hull.

3. Adjust as desired and tighten the nut and bolt.

Battery Placement

• For rough water move the batteries toward the back of the boat.

• In smooth water you can move the batteries forward more to

gain speed.

• Move the batteries forward if the boat wants to porpoise.

Trim Tabs

• In smooth water conditions, lowing the trim tabs can

help balance the ride of the boat by maximizing the

prop strut to gain speed, while the trim tabs help keep

the nose of the boat lower.

• In rough water, raise the trim tabs to help keep the

bow of the boat riding high.

• Trim tabs are used to give your boat a flat riding stance

when at speed. If your boat is leaning to one side

simply increase the depth of the trim tab on the side

that is deeper in the water to balance the boat laterally.

1. Loosen the nut securing the trim tab setting.

2. Adjust the bolt to hold the trim tab at the desired angle.

3. Tighten the nut to prevent the bolt from moving.

Turn Fins

• In smooth water conditions and for high speed

performance, raise the turn fins to increase speed.

• In rough water and for more turning authority, lower

the turn fins.

1. Loosen nut and bolt securing turn fin.

2. Tighten the nut and bolt while holding the turn fin at the

desired angle.

Tuning For Optimal Performance

There are four main features which can be adjusted on your Impulse 32 boat to tune it for optimal performance. Tuning is a

balance of these settings; making a change to any of these settings may require you to adjust other settings elsewhere. It is

normal and highly recommended to tune your boat for the boating conditions for the best performance every time you take your

boat out. When water conditions change, as a result you should make changes to fine tune your boat to the new conditions.

Getting accustomed to tuning your boat on a regular basis will help you achieve the best boating experience. Finding the proper

tuning settings will reduce the chance of a blow over and/or porpoising.

Impulse 32-Inch Brushless 6S Deep V

Always replace the drivetrain parts when they are damaged or

show visible wear or injury and damage may result.

Lubricating the flex shaft is vital to the life of the drivetrain.

The lubricant also acts as a water seal, keeping water from

entering the hull through the stuffing tube.

Lubricate the flex shaft and all moving parts after every 30

minutes of operation. Remove, clean, and lubricate the flex

shaft after every boating session.

1. In the hull, use two 10mm open-end wrenches to loosen

the collet nut from the flex shaft.

2. Slide the flex shaft out from the stuffing tube and drive

strut at the rear of the boat.

Tip: Use paper or cloth for cleaning and lubricating the flex

shaft and other drivetrain parts.

3. Wipe the old lubricant and material from the flex shaft.

4. Lubricate the full length of the flex shaft assembly up to

the drive dog using marine grease (PRB0101 or PRB0100).

Also apply grease to the collet threads.

5. Carefully reinstall the flex shaft in the drive strut, stuffing

tube and collet. If the flex shaft is difficult to remove or

install in the collet, use a flat screwdriver to spread the

grips of the collet.

Ensure there is a 1–2mm gap between the drive strut and

drive dog to allow for flex shaft shrinkage under load.

NOTICE: Operation in saltwater is not recommended.

Corrosion from exposure to saltwater will occur very quickly

after operation and cause damage to both mechanical and

electrical components. Damage from exposure to saltwater is

not covered under the warranty.

Drivetrain Lubrication

• After each use, remove the drain plug and hold the boat

upright to drain all water from inside the hull.

• Reinstall the drain plug.

• Fully dry the inside and outside of the boat, including the

water cooling lines and jacket around the motor.

• Remove the hatch before storing your boat. We

recommend placing the boat upside down to allow the

water to continue to drain.

• Repair any damage or wear to the boat.

• Make note of lessons learned from the trimming of your

boat, including water and wind conditions.

NOTICE: When you are finished boating, never leave the

boat in direct sunlight or in a hot, enclosed area such as a

car. Doing so can damage the boat.

After Boating and Maintenance

INSTRUCTION MANUAL

Rudder Service

1. Disconnect the water tube from the rudder.

2. Remove the nut, screw and linkage from the rudder

arm.

3. Turn the rudder and loosen the set screw from the

rudder pin.

4. Turn over the boat and lightly tap the rudder to remove

the pin.

5. Assemble in reverse order.

Water Cooling System

If water does not stream out of the water outlets while the

boat is moving forward, immediately stop the boat and clean

the obstruction from the water cooling system.

There are two separate water circuits in the Impulse 32. The

Water rudder pickup cools the motor. A pickup on the bottom

of the boat cools the ESC.

1. Disassemble and clean the water cooling system to

remove blockage and prevent overheating.

2. Replace damaged parts.

Propeller Service

1. Use an 8mm nut driver (DYN2805) to loosen the nut from the

driveshaft.

2. Remove the nut and propeller from the driveshaft.

3. Assemble in reverse order. Correctly align the propeller with

the drive dog on the driveshaft.

Impulse 32-Inch Brushless 6S Deep V

Binding

Binding is the process of programming the receiver to

recognize the GUID (Globally Unique Identiﬁer) code of a single

speciﬁc transmitter. The DX3

™

transmitter and SR315 receiver

are bound at the factory. If you need to rebind, follow the

instructions below.

You must rebind when:

• Different failsafe positions are desired e.g., when throttle or

steering reversing has been changed.

• Binding the receiver to a different transmitter.

• Binding the transmitter to a different receiver.

Hold the steering wheel and throttle trigger in the desired failsafe

positions during binding.

In the unlikely event that the radio

link is lost during use, the receiver will drive all channels to its

programmed failsafe position.

If using a SMART ESC and SMART battery, the transmitter

SMART Battery Level indicator will show the vehicle battery

level within 10 seconds of powering on and connecting.

Motor Care

• Prolong motor life by preventing overheating conditions.

Undue motor wear results from frequent turns, stops

and starts, pushing objects, boating in rough water or

vegetation and boating continuously at high speed.

• Over-temperature protection is installed on the ESC to

prevent circuit damage, but cannot protect the motor

from pushing against heavy resistance.

• Lubrication is important to prevent motor damage. If your

motor gets wet, lubricate the busings supporting the motor

shaft with light duty machine oil. Failure to do so can cause

the motor shaft to seize against the motor bushings.

CAUTION: Do not touch the motor until it has had time

to cool. It can become extremely hot when in use.

Radio and ECS Setup

The electronics installed in the Impulse 32 are fully configured and ready for operation out of the box. See the following

instructions for proper binding and failsafe setup and ESC calibration.

Power

Bind Button

DSMR Bind Process

1. Press and hold the bind button,

and Power ON the receiver; the

orange LED will begin to flash.

Release the bind button.

Bind Button

WARNING: Do not kink, cut or damage the antenna

wire. The antenna is made of a coaxial wire; if the

outer sheath becomes damaged, the receiver will not work

properly. If the antenna is damaged in any way, replace the

antenna before attempting to use the receiver.

SR315 Receiver

Speciﬁcations

Type:

Dual

Protocol 3 Ch Receiver

(SLT*/DSMR)

Dimensions (LxWxH):

32.5 x 21.5 x

12.4mm

Antenna Length:

90mm

Channels:

Weight:

Band:

2.4GHz

Voltage Range:

3.5–9.6V

Bind Type: Bind Button

*For SLT Bind information, review the

SR315 manual online at HorizonHobby.com

STR (Rudder Servo)

THR (ESC)

Receiver Antenna

The SR315 receivers feature a coaxial antenna design for easy

installation in almost any model. Think of the last 1 inch (32mm)

on the tip of the antenna as the active portion of the antenna,

the coaxial portion leading up to it is just an extension. Install the

antenna so the active portion is positioned as high as possible in

the vehicle, and not “in the shadow” of any carbon ﬁber or metal.

2. Set the trims and control positions at the desired failsafe

settings, press and hold the bind button, and power ON the

DX3 Smart transmitter.

3. When the orange LED on the DX3 Smart transmitter remains

lit, it is connected to SR315 receiver.

INSTRUCTION MANUAL

Programming with the SMART Programmer Box

ESC and Transmitter Calibration

1. Unplug the fan and connect the programming lead to the

fan port.

2. Connect a battery to the ESC.

3. Power on the box and select the parameter with the

SELECT button.

4. Change the values of the selected parameter with the EDIT

button

5. Press the SAVE button to save the changes. The ESC

requires a power cycle to implement the saved changes.

1. Begin with the transmitter and receiver binding complete.

2. Set your transmitter’s throttle channel to 100% travel and

trim to neutral.

3. Turn on your transmitter and connect a battery to the ESC but

don’t power it on.

4. Press and hold the Set button while turning on the ESC.

When the red LED begins to flash, release the Set button.

The ESC will enter programming mode if the button is

pressed for more than three seconds.

TIP: The red LED should be flashing when the ESC enters

calibration mode. If the green LED is flashing the ESC is in

programming mode.

5. Leave the throttle trigger at the neutral position, then press

and release the Set button. The red LED will stop flashing, the

green LED will flash one time and the motor will make a tone

to indicate the neutral position has been accepted.

6. Hold the throttle trigger at the full throttle position then

press and release the Set button. The green LED will flash

twice and the motor will make two tones to indicate the

full throttle position has been accepted.

7. Hold the throttle trigger at the full brake position then press

and release the Set button. The green LED will flash three

times and the motor will make three tones to indicate the

full brake position has been accepted.

The motor will operate normally after calibration is completed.

Programmable Items

Parameter Options

1 2 3 4 5 6 7 8 9

Running Mode Forward Only Forward/Reverse

LiPo Cells Auto Calc. 3S 4S 5S 6S 7S 8S

Cutoff Voltage Disabled 2.8V/Cell 3.0V/Cell 3.2V/Cell 3.4V/Cell

Timing (degree) 0.0 3.75 7. 5 11.25 15.0 18.75 22.5 26.25

Motor Rotation Clockwise Counterclockwise

160A Programmable Options

*The blacked out cells with white text are the default settings.

Impulse 32-Inch Brushless 6S Deep V

Troubleshooting Guide

Problem Possible Cause Solution

Boat will not respond to

throttle but responds to other

controls

Throttle channel is reversed Reverse throttle channel on transmitter

Extra noise or extra vibration

Damaged propeller, shaft or motor Replace damaged parts

Propeller is out of balance Balance or replace propeller

Reduced runtime or boat

underpowered

Boat battery charge is low Completely recharge battery

Boat battery is damaged Replace boat battery and follow battery instructions

Blocking or friction on shaft or propeller Disassemble, lubricate and correctly align parts

Boat conditions may be too cold

Make sure the battery is warm (above 10º C [50º F]) before

use

Battery capacity may be too low for

conditions

Replace battery or use a larger capacity battery

Drive dog is too near the prop strut

Loosen motor coupling on flex shaft and move flex shaft a

small amount

Too little lubrication on flex shaft Fully lubricate flex shaft

Vegetation or other obstacles block

the rudder or propeller

Remove vegetation or obstacles from rudder or propeller

Boat will not Bind (during

binding) to transmitter

Transmitter is too near boat during binding

process

Move powered transmitter a few feet from boat, discon-

nect and reconnect battery to boat

Boat or transmitter is too close to large

metal object, wireless source or another

transmitter

Move the boat and transmitter to another location and

attempt binding again

Another compatible transmitter is pow-

ered on within range of the receiver

Power off all compatible transmitters except the one you

are trying to bind

Boat battery/Transmitter battery charge

is too low

Replace/recharge batteries

ESC switch is off Power on ESC switch

Boat will not connect (after

binding) to transmitter

Transmitter is too near boat during

connecting process

Move powered transmitter a few feet from boat,

disconnect and reconnect battery to boat

Boat or transmitter is too close to large

metal object, wireless source or another

transmitter

Move boat or transmitter to another location and attempt

to connect again

Boat battery/transmitter battery charge is

too low

Replace/recharge batteries

ESC switch is off Power on ESC switch

Boat tends to dive in the

water or takes on water

The boat hull is not completely closed

Dry out the boat and ensure the hatch is fully closed on

the hull before returning the boat to the water

Center of gravity is too far forward Move batteries back in the hull

Boat tends to turn one

direction

Rudder or rudder trim is not centered

Repair rudder or adjust rudder and rudder trim for straight

running when control is at neutral

Rudder does not move

Rudder, linkage or servo damage Replace or repair damaged parts and adjust controls

Steering servo wire is damaged or con-

nections are loose

Do a check of steering servo wires and connections,

connect or replace as needed

Transmitter is not bound correctly Re-bind

BEC (Battery Elimination Circuit) of the

ESC is damaged

Replace ESC

ESC switch is off Power on ESC switch

Controls reversed Transmitter settings are reversed

Do the Control Direction Test and adjust controls on

transmitter appropriately

Motor overheats Blocked water cooler tubes Clean or replace water tubes

Motor power pulses then

motor loses power

ESC uses default soft Low Voltage Cutoff

(LVC)

Recharge boat battery or replace battery that is no longer

performing

Weather conditions might be too cold Postpone until weather is warmer

Battery is old, worn out or damaged Replace battery

INSTRUCTION MANUAL

Replacement Parts

Optional Items

Recommended Items

Part # Description

FUG4300BP4 AA Alkaline Battery (4)

PRB281087 Grease Guard Set: Impulse 32

PRB281088 Receiver Box Set: Impulse 32

PRB281096 Hull & Cnpy Set blk: Impulse 32

PRB281097 Bulk Head Fit Set: Impulse 32

PRB281098 Trim Tab Set: Impulse 32

PRB281099 Turn Fin Set: Impulse 32

PRB281100 Rudder Set: Impulse 32

PRB281121 Hull & Cnpy Set, Wht: Impulse 32

PRB282079 Flex Shaft 5 x 260mm: Impulse 32

PRB282080 Stufﬁng Tube: Impulse 32

PRB282081 Propeller Strut Set: Impulse 32

PRB282089 Propeller: 42-inch Blackjack

PRB282092 Motor Mount Set: Impulse 32

PRB285003 Break Away Bolt: Impulse 32

PRB286070 Steering Pushrod Set: Impulse 32

PRB286072 Rubber Seal Set: Impulse 32

PRB286074 Boat Stand: Impulse 32

PRB289006 Decal Set BLK/GRN: Impulse 32

SPMR2340 DX3 Smart Transmitter

SPMS605 9KG Servo, WP, Metal Cent. Case 23T

SPMSR315 SR315 DSMR 3 CH Receiver

SPMXMM1100 Firma 2000Kv Brushless Marine Motor

SPMXSE1160M Firma 160A Smart BL Marine ESC

Part # Description

DYN1400 LiPo Charge Protection Bag,Small

DYN4403 GPS Speed Meter 2.0

DYNF1055 Infrared Temp Gun w/ Laser

DYNT0502 Start Up Tool Set: Proboat

SPM5010 DX5 Pro DSMR Tx w/SR2100

SPMSS6250 S6250 U-T / H-S Digital HV WP Servo

SPMXBC100 SMART Battery & Servo Tester

SPMXCA200 Avian Firma Smart ESC Programmer

Part # Description

DYNE4200 Grease Gun w/ Marine Grease 5oz

DYNM0102 Clear Flex Marine Tape (18M)

SPMX50003S100H5 5000mAh 3S 11.1V Smart 100C; IC5

SPMXC1010 Smart S2100 AC Charger, 2X100W

SPMXCA507 Adapter: IC3 Battery/IC5 Device

Limited Warranty

What this Warranty Covers

Horizon Hobby, LLC, (Horizon) warrants to the original purchaser

that the product purchased (the “Product”) will be free from

defects in materials and workmanship for a period of 2 years from

the date of purchase.

What is Not Covered

This warranty is not transferable and does not cover (i) cosmetic

damage, (ii) damage due to acts of God, accident, misuse, abuse,

negligence, commercial use, or due to improper use, installation,

operation or maintenance, (iii) modification of or to any part of the

Product, (iv) attempted service by anyone other than a Horizon

Hobby authorized service center, (v) Product not purchased

from an authorized Horizon dealer, or (vi) Product not compliant

with applicable technical regulations or (vii) use that violates any

applicable laws, rules, or regulations.

OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON

MAKES NO OTHER WARRANTY OR REPRESENTATION, AND

HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES,

INCLUDING, WITHOUT LIMITATION, THE IMPLIED

WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE. THE PURCHASER

ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT

THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF

THE PURCHASER’S INTENDED USE.

Purchaser’s Remedy

Horizon’s sole obligation and purchaser’s sole and exclusive remedy

shall be that Horizon will, at its option, either (i) service, or (ii)

replace, any Product determined by Horizon to be defective. Horizon

reserves the right to inspect any and all Product(s) involved in a

warranty claim. Service or replacement decisions are at the sole

discretion of Horizon. Proof of purchase is required for all warranty

claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER

THIS WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE

REMEDY.

Limitation of Liability

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT,

INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF

PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY

WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED

IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT

LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF

HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH

DAMAGES. Further, in no event shall the liability of Horizon exceed

the individual price of the Product on which liability is asserted.

As Horizon has no control over use, setup, final assembly,

modification or misuse, no liability shall be assumed nor accepted

for any resulting damage or injury. By the act of use, setup or

assembly, the user accepts all resulting liability. If you as the

purchaser or user are not prepared to accept the liability associated

with the use of the Product, purchaser is advised to return the

Product immediately in new and unused condition to the place of

purchase.

Law

These terms are governed by Illinois law (without regard to conflict

of law principals). This warranty gives you specific legal rights, and

you may also have other rights which vary from state to state.

Horizon reserves the right to change or modify this warranty at any

time without notice.

WARRANTY SERVICES

Questions, Assistance, and Services

Your local hobby store and/or place of purchase cannot provide

warranty support or service. Once assembly, setup or use of the

Product has been started, you must contact your local distributor

or Horizon directly. This will enable Horizon to better answer your

questions and service you in the event that you may need any

assistance. For questions or assistance, please visit our website

Impulse 32-Inch Brushless 6S Deep V

at www.horizonhobby.com, submit a Product Support Inquiry,

or call the toll free telephone number referenced in the Warranty

and Service Contact Information section to speak with a Product

Support representative.

Inspection or Services

If this Product needs to be inspected or serviced and is compliant

in the country you live and use the Product in, please use the

Horizon Online Service Request submission process found on

our website or call Horizon to obtain a Return Merchandise

Authorization (RMA) number. Pack the Product securely using a

shipping carton. Please note that original boxes may be included,

but are not designed to withstand the rigors of shipping without

additional protection. Ship via a carrier that provides tracking and

insurance for lost or damaged parcels, as Horizon is not responsible

for merchandise until it arrives and is accepted at our facility. An

Online Service Request is available at http://www.horizonhobby.

com/content/service-center_render-service-center. If you do not

have internet access, please contact Horizon Product Support to

obtain a RMA number along with instructions for submitting your

product for service. When calling Horizon, you will be asked to

provide your complete name, street address, email address and

phone number where you can be reached during business hours.

When sending product into Horizon, please include your RMA

number, a list of the included items, and a brief summary of the

problem. A copy of your original sales receipt must be included for

warranty consideration. Be sure your name, address, and RMA

number are clearly written on the outside of the shipping carton.

NOTICE: Do not ship Li-Po batteries to Horizon. If you

have any issue with a Li-Po battery, please contact the

appropriate Horizon Product Support office.

Warranty Requirements

For Warranty consideration, you must include your original sales

receipt verifying the proof-of-purchase date. Provided warranty

conditions have been met, your Product will be serviced or

replaced free of charge. Service or replacement decisions are at

the sole discretion of Horizon.

Non-Warranty Service

Should your service not be covered by warranty, service will be

completed and payment will be required without notification

or estimate of the expense unless the expense exceeds 50%

of the retail purchase cost. By submitting the item for service

you are agreeing to payment of the service without notification.

Service estimates are available upon request. You must include

this request with your item submitted for service. Non-warranty

service estimates will be billed a minimum of ½ hour of labor.

In addition you will be billed for return freight. Horizon accepts

money orders and cashier’s checks, as well as Visa, MasterCard,

American Express, and Discover cards. By submitting any item

to Horizon for service, you are agreeing to Horizon’s Terms and

Conditions found on our website http://www.horizonhobby.com/

content/service-center_render-service-center.

ATTENTION: Horizon service is limited to Product

compliant in the country of use and ownership. If

received, a non-compliant Product will not be serviced.

Further, the sender will be responsible for arranging

return shipment of the un-serviced Product, through a

carrier of the sender’s choice and at the sender’s

expense. Horizon will hold non-compliant Product for a

period of 60 days from notification, after which it will be

discarded.

10/15

Country of

Purchase

Horizon Hobby Contact Information Address

United

States of

America

Horizon Service Center

(Repairs and Repair Requests)

servicecenter.horizonhobby.com/RequestForm/

2904 Research Rd.

Champaign, Illinois,

61822 USA

Horizon Product Support

(Product Technical Assistance)

productsupport@horizonhobby.com

877-504-0233

Sales

websales@horizonhobby.com

800-338-4639

Horizon Technischer Service service@horizonhobby.de

Hanskampring 9

D 22885 Barsbüttel,

Germany

Sales: Horizon Hobby GmbH +49 (0) 4121 2655 100

Warranty and Service Contact Information*

INSTRUCTION MANUAL

*For the most up-to-date

customer service contact information, please visit: www.horizonhobby.com/content/service-center-render-service-center

DX3 Transmitter Contains FCC ID: BRWKATY1T

SR315 Receiver FCC ID: BRWSRIRVINGV1

This equipment complies with FCC and IC radiation exposure

limits set forth for an uncontrolled environment. This

equipment should be installed and operated with minimum

distance 20cm between the radiator and/or antenna and your

body (excluding fingers, hands, wrists, ankles and feet). This

transmitter must not be co-located or operating in conjunction

with any other antenna or transmitter.

Supplier’s Declaration of Conformity

Lucas Oil Impulse 32-inch BL V Hull w/Smart, RTR

(PRB08037)

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2)

this device must accept any interference received, including

interference that may cause undesired operation.

CAUTION: Changes or modiﬁcations not expressly

approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to part

15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is

no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for

help.

Horizon Hobby, LLC

2904 Research Rd.,

Champaign, IL 61822

Email: compliance@horizonhobby.com

Web: HorizonHobby.com

FCC Information

IC Information

DX3 Transmitter Contains IC: 6157A-KATY1T

SR315 Receiver IC: 6157A-SRIRVINGV1

CAN ICES-3 (B)/NMB-3(B)

This device contains license-exempt transmitter(s)/receivers(s)

that comply with Innovation, Science, and Economic Develop-

ment Canada’s license-exempt RSS(s). Operation is subject to

the following 2 conditions:

1. This device may not cause interference.

2. This device must accept any interference, including interfer-

ence that may cause undesired operation of the device.

Compliance Information for the European Union

ucas Oil Impulse 32-inch BL V Hull w/Smart, RTR

(PRB08037) Hereby, Horizon Hobby, LLC declares

that the device is in compliance with the following:

EU Radio Equipment Directive 2014/53/EU;

RoHS 2 Directive 2011/65/EU;

RoHS 3 Directive - Amending 2011/65/EU Annex II 2015/863.

The full text of the EU declaration of conformity is

available at the following internet address: https://www.

horizonhobby.com/content/support-render-compliance.

NOTE: This product contains batteries that are covered under

the 2006/66/EC European Directive, which cannot be disposed of

with normal household waste. Please follow local regulations.

DX3 Smart Transmitter Wireless Frequency Range and

Wireless Output Power: 2402-2478 MHz / 17.7 dBm

SR315 Receiver Wireless Frequency Range and

Wireless Output Power: 2404-2476 MHz / -1.33 dBm

EU Manufacturer of Record:

Horizon Hobby, LLC

2904 Research Road

Champaign, IL 61822 USA

EU Importer of Record:

Horizon Hobby, GmbH

Hanskampring 9

22885 Barsbüttel Germany

WEEE NOTICE:

This appliance is labeled in accordance with

European Directive 2012/19/EU concerning

waste of electrical and electronic equipment

(WEEE). This label indicates that this product

should not be disposed of with household

waste. It should be deposited at an appropriate facility

to enable recovery and recycling.

Impulse 32-Inch Brushless 6S Deep V

BEDIENUNGSANLEITUNG

Als Benutzer dieses Produkts sind Sie allein dafür verantwortlich,

es so zu betreiben, dass es Sie selbst und andere nicht gefährdet

und dass es zu keiner Beschädigung des Produkts oder des

Eigentums Dritter kommt.

• Fassen Sie beim Handling oder Transport das Boot immer von

seiten an und halten alle bewegliche Teile weg vom Körper.

• Halten Sie stets in allen Richtungen einen Sicherheitsabstand

um Ihr Modell, um Zusammenstöße oder Verletzungen

zu vermeiden. Dieses Modell wird von einem Funksignal

gesteuert, das Interferenzen von vielen Quellen außerhalb

Ihres Einflussbereichs unterliegt. Diese Interferenzen können

einen kurzzeitigen Steuerungsverlust verursachen.

• Betreiben Sie Ihr Modell immer auf einer Freifläche ohne

Fahrzeuge in voller Größe, Verkehr oder Menschen.

• Befolgen Sie stets sorgfältig die Anweisungen und

Warnhinweise für das Modell und jegliche optionalen

Hilfsgeräte (Ladegeräte, Akkupacks usw.).

• Bewahren Sie alle Chemikalien, Klein- und Elektroteile stets

außerhalb der Reichweite von Kindern auf.

• Setzen Sie Geräte, die für diesen Zweck nicht speziell

ausgelegt und geschützt sind, niemals Wasser aus.

Feuchtigkeit kann die Elektronik beschädigen.

• Stecken Sie keinen Teil des Modells in den Mund, da dies zu

schweren Verletzungen oder sogar zum Tod führen kann.

• Betreiben Sie Ihr Modell nie mit fast leeren Senderakkus.

Zusätzliche Sicherheitsvorkehrungen und Warnhinweise

Dies ist ein hochentwickeltes Hobby-Produkt. Es muss mit Vorsicht und gesundem Menschenverstand betrieben werden und

benötigt gewisse mechanische Grundfähigkeiten. Wird dieses Produkt nicht auf eine sichere und verantwortungsvolle Weise

betrieben, kann dies zu Verletzungen oder Schäden am Produkt oder anderen Sachwerten führen. Versuchen Sie nicht ohne

Genehmigung durch Horizon Hobby, LLC, das Produkt zu zerlegen, es mit inkompatiblen Komponenten zu verwenden oder

auf jegliche Weise zu erweitern. Diese Bedienungsanleitung enthält Anweisungen für Sicherheit, Betrieb und Wartung. Es ist

unbedingt notwendig, vor Zusammenbau, Einrichtung oder Verwendung alle Anweisungen und Warnhinweise im Handbuch

zu lesen und zu befolgen, damit es estimmungsgemäß betrieben werden kann und Schäden oder schwere Verletzungen

vermieden werden.

HINWEIS

SPEZIELLE BEDEUTUNGEN

Allen Anweisungen, Garantien und anderen zugehörigen Dokumenten sind Änderungen nach Ermessen von Horizon Hobby,

LLC vorbehalten. Aktuelle Produktliteratur finden Sie unter www.horizonhobby.com oder www.towerhobbies.com im Support-

Abschnitt für das Produkt.

Die folgenden Begriffe werden in der gesamten Produktliteratur verwendet, um auf unterschiedlich hohe Gefahrenrisiken beim

Betrieb dieses Produkts hinzuweisen:

WARNUNG: Wenn diese Verfahren nicht korrekt befolgt werden, ergeben sich wahrscheinlich Sachschäden, Kollateralschäden und

schwere Verletzungen ODER mit hoher Wahrscheinlichkeit oberﬂächliche Verletzungen.

ACHTUNG: Wenn diese Verfahren nicht korrekt befolgt werden, ergeben sich wahrscheinlich Sachschäden UND die Gefahr von

schweren Verletzungen.

HINWEIS: Wenn diese Verfahren nicht korrekt befolgt werden, können sich möglicherweise Sachschäden UND geringe oder keine

Gefahr von Verletzungen ergeben.

WARNUNG: Lesen Sie die GESAMTE Bedienungsanleitung, um sich vor dem Betrieb mit den Produktfunktionen vertraut

zu machen. Wird das Produkt nicht korrekt betrieben, kann dies zu Schäden am Produkt oder persönlichem Eigentum führen

oder schwere Verletzungen verursachen.

Altersempfehlung: Nicht für Kinder unter 14 Jahren. Dies ist kein Spielzeug.

Ihr neues Horizon Hobby Boot wurde mit einer Kombination

von wasserdichten und spritzwassergeschützten

Komponenten entwickelt die es ihnen ermöglichen das Modell

bei ruhigen Bedingungen in Süßwasser zu betreiben.

Obwohl das Boot spritzwassergeschützt ist es nicht

vollständig wasserdicht und darf keines Falls wie ein U-Boot

behandelt werden. Die verschiedenen elektronischen

Komponenten wie der Regler, die Servos ubd der Empfänger

sind wasserdicht, die meisten mechanische Komponenten

sind aber nur spritzwassergeschützt und erfordern nach

Betrieb zusätzliche Wartung.

Metallteile, inklusive der Lager, Schrauben und Muttern,

Propeller, Ruder, Ruderhalter und Propellerstrebe sowie die

Kontakte in den elektrischen Kabeln sind anfällig für Korrosion

wenn nach dem Einsatz in feuchter Umgebung zusätzliche

Wartungsarbeiten nicht durchgeführt werden. Um die

Langzeitleistung ihres Bootes zu maximieren und die Garantie

aufrecht zu halten müssen diese Wartungsarbeiten regelmäßig

durchführen.

ACHTUNG: Unaufmerksamkeit während des

Betriebes des Produktes in Zusammenhang mit den

folgenden Sicherheitshinweisen kann zu Fehlfunktionen und

dem Verlust der Garantie führen.

Spritzwassergeschützes Boot mit wasserdichter Elektronik

Impulse 32-Inch Brushless 6S Deep V

Allgemeine Sicherheitshinweise

• Bitte lesen Sie sich die Wartungsanleitung sorgfältig durch und stellen

sicher, dass Sie alle Werkzeuge für eine Wartung des Bootes haben.

• Nicht alle Akkutypen sind für den Einsatz in feuchter

Umgebung geeignet. Fragen Sie dazu vor dem Einsatz den

Hersteller des Akkus. Besondere Aufmerksamkeit sollten Sie

bei dem Einsatz von LiPo Akkus wallten lassen.

• Die meisten Sender sind nicht wasserfest. Sehen Sie bitte

dazu vor Inbetriebnahme in der Bedienungsanleitung ihres

Senders nach oder kontaktieren Sie den Hersteller.

• Betreiben Sie ihr Boot niemals bei Gewitter.

• Nehmen Sie niemals den Sender bei Blitzen oder Gewitter in Betrieb.

Wartungsanleitung nach Einsatz

in feuchter Umgebung

• Nehmen Sie die Kabinenhaube und Ablaufstopfen ab und

kippen das Boot in die Richtung des Ablauf bis alles Wasser

was sich gesammelt hat abgelaufen ist.

ACHTUNG: Halten Sie immer Hände, Finger,

Werkzeuge oder anderen lose, hängende Objekte weg

von drehenden Teilen wenn Sie das Boot trocknen.

• Entnehmen Sie den Akkupack und trockenen die Kontakte. Sollten

Sie einen Kompressor oder Druckluftflasche zur Hand haben

blasen Sie damit das Wasser aus den Gehäusevertiefungen.

• Trocknen und schmieren Sie die Teile alle 30 Betriebsminuten

oder immer dann wenn das Boot ein- oder untergetaucht war.

HINWEIS: Verwenden Sie keinen Hochdruckreiniger um

das Fahrzeug zu reinigen.

• Reinigen Sie das Fahrzeug mit Druckluft aus einem

Kompressor oder einer Druckluftflasche und entfernen so das

Wasser aus den Spalten und Ecken.

• Sprühen Sie die Lager, Wellen, Befestigungen mit WD-40 Öl

oder einem vergleichbaren wasserverdrängenden Leichtöl ein.

• Lassen Sie das Fahrzeug vor dem Einlagern vollständig

trocknen. Das Abtropfen von Wasser (und Öl) kann durchaus

ein paar Stunden dauern.

Spezifikationen

Länge 837mm (32,95 Zoll)

Breite 9,36 in (238 mm)

Sender

DX3 SMART DSMR 3 CH

(SPMR2340)

Empfänger

SR315 3CH Receiver

(

SPMSR315

)

Rumpfmaterial Fiberglas

Motor

Firma 2000Kv Bürstenloser Schiffsmotor

1900Kv

(SPMXMM1100)

ESC

Firma 160A

SMART

Bürstenloser Marine-

Geschwindigkeitsregler

(

SPMXSE1160M

)

Servo

Wasserdichtes Servo

(

SPMS605

)

Akkus Sender: 4 AA-Akkus

Boot: (2) 11,1V 5000mAh 3S 100C SMART

LiPo, Hardcase, IC5 (SPMX50003S100H5)

(separat erhältlich)

Inhaltsverzeichnis

9.36 in

(238mm)

32.95 in (837mm)

Packungsinhalt ........................................................................19

Erforderliches Werkzeug und Materialien ...............................19

Akku und Ladegerät ...............................................................19

Einsetzen der Akkupacks ........................................................19

Montage des Antennenröhrchen ........................................... 20

Senderfunktionen .................................................................. 20

Einsetzen der Senderbatterien .............................................. 20

Spektrum SMART-Technologie .............................................. 20

Niederspannungsabschaltung (LVC) ....................................... 21

Zum Starten ........................................................................... 21

Kontrolle ................................................................................ 21

Testen des Bootes im Wasser .............................................. 22

Tips für das Fahren ................................................................ 22

Nach dem Fahren .................................................................. 22

Abstimmung für optimale Leistung ....................................... 23

Einstellung des Propellerwinkels........................................... 23

Platzierung der Batterie ......................................................... 23

Trimmklappen ........................................................................ 23

Flossen drehen ..................................................................... 23

Wartungsarbeiten nach dem Fahren .................................... 24

Fetten der Welle .................................................................... 24

Kühlwassersystem ................................................................ 25

Wartung des Ruders .............................................................. 25

Propellerwartung ................................................................... 25

Motorpflege ........................................................................... 26

Funk- und ECS-Einrichtung .................................................... 26

SPMSR315 Empfänger .......................................................... 26

Binden ................................................................................... 26

DSMR-Bindungsprozess ........................................................ 26

Empfängerantenne ................................................................ 26

Kalibrierung von Geschwindigkeitsregler und Sender ........... 27

Programmieren mit der Programmierbox .............................. 27

Programmierbare Optionen für 160A ................................... 27

Problemlösung ....................................................................... 28

Ersatzteile .............................................................................. 29

Garantie und Service Informationen ...................................... 29

Empfohlene Artikel ................................................................ 29

Optionale Komponenten........................................................ 29

Garantie und Service Kontaktinformationen .......................... 30

Rechtliche Informationen für die Europäische Union ............ 30

Produktüberprüfung

Entnehmen Sie vorsichtig das Boot und den Sender der Box.

Überprüfen Sie das Boot auf evtl. Schäden. Sollten Sie Schäden

feststellen kontaktieren Sie den Händler bei dem Sie das Boot

gekauft haben, oder den Product Support kontaktieren. Siehe

den Abschnitt zu Garantie und Kundendienstinformationen zu

weiteren Informationen.

BEDIENUNGSANLEITUNG

Packungsinhalt

• Pro Boat

Impulse™ 32 inch Bürstenloser RTR Catamaran

• Spektrum DX3 SMART DSMR

3-Kanal-Sender (SPMR2340)

• Spektrum SR315 3CH-Empfänger (SPMSR315)

• Spektrum Firma™ 160A SMART Bürstenloser Marine-

Geschwindigkeitsregler (SPMXSE1160M)

• Spektrum 9KG Servo, WP, Metal Cent. Gehäuse 23T

(SPSM605)

• Firma 2000Kv bürstenloser Schiffsmotor (SPMXMM1100v)

• 4 AA-Akkus

Einsetzen der Akkupacks

1. Lösen Sie die vier Flügelschrauben an der Akku-

Abdeckung und nehmen Sie sie vom Rumpf ab.

2. Befestigen Sie eine Seite des beiliegenden Klettbands

an der Akkuhalterung. Befestigen Sie die andere Seite

des Klettbands an der Rückseite des Akkus.

3. Die vollständig geladenen Akkus vollständig vorne in

Akkufach einlegen und mit dem Klettband sichern.

4. Verbinden Sie die Akkus mit dem Geschwindigkeitsregler.

WARNUNG: Bei der Verwendung von zwei Akkus

immer sicherstellen, dass die Akkus von ähnlichem

Typ sind (Spannung und Kapazität). Das Anschließen

von Akkus unterschiedlicher Kapazität kann zu einer

Tiefenentladung des Akkus führen, was zu einem Brand mit

Sach- oder Personenschäden führen kann.

Erforderliches Werkzeug und Materialien

• Schraubenschlüssel

• Spitzzange

• Papiertücher

• Reinigungsalkohol

• Phillips Schraubendreher: #1, #2

• Inbusschlüssel: 1.5mm und 2mm

• Transparentes Klebeband (DYNM0102)

• Pro Boat Marine Fett und Applikator (DYNE4200)

Der Impulse 32 boat benötigt einen 3S LiPo-Hartschalen-Akku mit

IC5-Stecker (nicht im Lieferumfang enthalten). Der im Lieferumfang

enthaltene Spektrum™ Firma™ SMART 130A bürstenlose

Geschwindigkeitsregler (SPMXSE1130) verfügt über einen IC5™-

Akku-Anschluss. Wir empfehlen einen Spektrum 5000mAh 3S

11.1V 100C SMART LiPo-Akku (SPMX50003S100H5).

Wir empfehlen zudem das Laden von Spektrum SMART-Akkus

mit Spektrum Smart-Ladegeräten, da Smart-Ladegeräte die

Ladeeinstellungen für Smart-Akkus automatisch konfigurieren. Wir

empfehlen das Spektrum S1100 SMART AC Ladegerät, 1 x 100w

(SPMXC1080) mit IC3- bis IC5-Ladeadapter (SPMXCA507).

In den Bedienungsanleitungen für Akku und Ladegerät finden Sie

Informationen zur Nutzung, Sicherheit und zum Laden.

HINWEIS: Laden Sie niemals ein Akku im Boot, da sonst

ein Schaden auftreten könnte.

Akku und Ladegerät

A/B

Spektrum SMART-Technologie

Der Impulse 32 boat ist im Geschwindigkeitsregler und Empfänger

mit der Spektrum SMART-Technologie ausgestattet, die Ihnen

Telemetrieinformationen wie Akku-Spannung Ihres Fahrzeugs

liefern kann. Der im Lieferumfang enthaltene DX3 Smart Sender

verfügt über eine LED-Anzeige, die während des Betriebs den

Akkuladezustand Ihres Fahrzeugs anzeigt.

Für zusätzliche Smart-Funktionalität sollten Sie ein Upgrade auf

einen fortschrittlicheren Smart-Technologie-kompatiblen Spektrum-

Sender wie den DX5C (nur SPMR5100-Sender) oder DX5 Pro (nur

SPMR5010-Sender) in Betracht ziehen. Betreiben Sie den Impulse

32 boat mithilfe von Spektrum Smart-Akkus, um die Smart-

Technologie optimal nutzen zu können. So lassen sich Akku-Daten

ebenfalls detailliert an das System übertragen.

Weitere Informationen erhalten Sie unter www.SpektrumRC.com.

Führen Sie die Antenne in das Antennenröhrchen wie

abgebildet ein. Das Ende der Antenne nicht über das

Antennenrohr biegen und die Kappe darüber platzieren,

da sonst Schäden entstehen können. Zur einwandfreien

Funktion muß die Antenne nicht ausserhalb des

Röhrchens geführt werden.

Das Ende der Antenne muß sich für den besten

Empfang überhalb der Wasserlinie befinden.

HINWEIS: Kürzen oder knicken Sie die Antennen nicht,

da sonst die Gefahr von Beschädigungen besteht.

Montage des Antennenröhrchen

Senderfunktionen

Taste Kanal 3

Throttle/Brake (Gas/Bremse)

Steuerrad

Steuerrate

Passt den Endpunkt der Steuerung an

Bremsrate

Passt den Endpunkt der Bremsung an.

Steuertrimmung

Zur Anpassung des Steuermittelpunkts. Normalerweise wird die

Steuertrimmung solange eingestellt, bis das Fahrzeug gerade in

der Spur läuft.

Gastrimmung

Zur Anpassung des Gasnullpunktes

Ladezustandsanzeige SMART-Akku

Umkehren der Servolaufrichtung

Um den Kanal für die Gaszufuhr (TH) oder die Steuerung

(ST) umzukehren, die Position des entsprechenden Schalters

umschalten – „N“ steht für normal, „R“ für Umkehren.

Begrenzung Gaszufuhr

Begrenzt die Gaszufuhr auf 50/75/100%

Wählen Sie 50% oder 75% für Fahrer mit geringer Erfahrung

oder wenn das Fahrzeug in einem kleinen Bereich gefahren wird.

Strom-LED

• Durchgängig rot: Zeigt die Funkverbindung und die

ausreichende Akkuladung an

• Rot blinkend: Zeigt an, dass die Akku-Spannung kritisch

niedrig ist. Akkus ersetzen

Ein-/Ausschalter

Bindungsschalter

A/B.

Einsetzen der Senderbatterien

Für den Betrieb sind 4 AA Batterien erforderlich.

1. Nehmen Sie die Batterieklappe vom Sender ab.

2. Setzen Sie die Batterien wie abgebildet ein.

3. Setzen Sie die Batterieklappe wieder auf.

ACHTUNG: Entfernen Sie niemals Batterien aus dem Sender, während

das Modell eingeschaltet ist. Ein Verlust der Kontrolle über das Modell,

Schäden oder Verletzungen können auftreten.

ACHTUNG: Wenn Sie wiederauﬂadbare Akkus verwenden dürfen Sie nur

diese laden. Das Laden von nicht auﬂadbaren Batterien könnte diese zur

Explosion bringen, was Sach- und Personenschäden zur Folge haben könnte.

ACHTUNG: Es besteht Explosionsrisiko wenn die Akkus durch einen

falschen Typ ersetzt werden. Entsorgen Sie verbrauchte Batterien den

Vorschriften entsprechend.

Impulse 32-Inch Brushless 6S Deep V

La page charge ...

Pro Boat PRB08037T1 Le manuel du propriétaire

Marque: Pro Boat

Modèle: PRB08037T1

Catégorie: Jouets télécommandés

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

italiano: Pro Boat PRB08037T1 Manuale del proprietario
English: Pro Boat PRB08037T1 Owner's manual
Deutsch: Pro Boat PRB08037T1 Bedienungsanleitung

Pro Boat PRB08037T1 Le manuel du propriétaire

Ce manuel convient également à

Pro Boat PRB08037T1 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents