Axial AXI03000T2 Le manuel du propriétaire

Marque: Axial

Modèle: AXI03000T2

Catégorie: Jouets télécommandés

Taper: Le manuel du propriétaire

Ce manuel convient également à

INSTRUCTION MANUAL

BEDIENUNGSANLEITUNG

MANUEL D’UTILISATION

MANUALE DI ISTRUZIONI

AXI03000

Age Recommendation: Not for children under 14 years. This is not a toy.

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the

product correctly can result in damage to the product, personal property and cause serious injury.

This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to

operate this Product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for

use by children without direct adult supervision. Do not use with incompatible components or alter this product in any way outside of the instructions

provided by Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the

instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.

NOTICE

All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product

literature, visit horizonhobby.com or towerhobbies.com and click on the support or resources tab for this product.

MEANING OF SPECIAL LANGUAGE

The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:

WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a

high probability of superﬁ cial injury.

CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.

NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no possibility of injury.

As the user of this product, you are solely responsible for operating in a manner that does not endanger yourself and others or result in damage to the

product or property of others.

This model is controlled by a radio signal subject to interference from many sources outside your control. This interference can cause momentary loss of

control, so it is advisable to always keep a safe distance in all directions around your model as this margin will help avoid collisions or injury.

• Never operate your model with low transmitter batteries.

• Always operate your model in open spaces away from full-size vehicles,

trafﬁ c and people.

• Never operate the model in the street or in populated areas for any reason.

• Carefully follow the directions and warnings for this and any optional

support equipment (chargers, rechargeable battery packs, etc.) you use.

• Keep all chemicals, small parts and anything electrical out of the reach

of children.

• Never lick or place any portion of the model in your mouth as it could

cause serious injury or even death.

• Exercise caution when using tools and sharp instruments.

• Take care during maintenance as some parts may have sharp edges.

• Immediately after using your model, do NOT touch equipment such as

the motor, electronic speed control and battery, because they generate

high temperatures. You may burn yourself seriously touching them.

• Do not put ﬁ ngers or any objects inside rotating and moving parts, as this

may cause damage or serious injury.

• Always turn on your transmitter before you turn on the receiver in the

car. Always turn off the receiver before turning your transmitter off.

• Keep the wheels of the model off the ground when checking the

operation of the radio equipment.

SAFETY PRECAUTIONS AND WARNINGS

WARNING AGAINST COUNTERFEIT PRODUCTS: Always purchase from a Horizon Hobby, LLC authorized dealer to ensure authentic

high-quality Spektrum product. Horizon Hobby, LLC disclaims all support and warranty with regards, but not limited to, compatibility and

performance of counterfeit products or products claiming compatibility with Spektrum technology.

Your new Horizon Hobby vehicle has been designed and built with a

combination of waterproof and water-resistant components to allow you to

operate the product in many “wet conditions,” including puddles, creeks,

wet grass, snow and even rain.

While the entire vehicle is highly water-resistant, it is not completely

waterproof and your vehicle should NOT be treated like a submarine. The

various electronic components used in the vehicle, such as the Electronic

Speed Control (ESC), servo(s) and receiver are waterproof, however, most

of the mechanical components are water-resistant and should not be

submerged.

Metal parts, including the bearings, hinge pins, screws and nuts, as well

as the contacts in the electrical cables, will be susceptible to corrosion if

additional maintenance is not performed after running in wet conditions.

To maximize the long-term performance of your vehicle and to keep

the warranty intact, the procedures described in the “Wet Conditions

Maintenance” section below must be performed regularly if you choose

to run in wet conditions. If you are not willing to perform the additional

care and maintenance required, then you should not operate the vehicle in

those conditions.

CAUTION: Failure to exercise caution while using this product

and complying with the following precautions could result in

product malfunction and/or void the warranty.

GENERAL PRECAUTIONS

• Read through the wet conditions maintenance procedures and make sure

that you have all the tools you will need to properly maintain your vehicle.

• Not all batteries can be used in wet conditions. Consult the battery

manufacturer before use. Caution should be taken when using Li-Po

batteries in wet conditions.

• Most transmitters are not water-resistant. Consult your transmitter’s

manual or the manufacturer before operation.

• Never operate your transmitter or vehicle where lightning may be present.

• Do not operate your vehicle where it could come in contact with salt

water (ocean water or water on salt-covered roads), contaminated or

polluted water. Salt water is very conductive and highly corrosive, so

use caution.

• Even minimal water contact can reduce the life of your motor if it

has not been certiﬁ ed as water-resistant or waterproof. If the motor

becomes excessively wet, apply very light throttle until the water is

mostly removed from the motor. Running a wet motor at high speeds may

rapidly damage the motor.

• Driving in wet conditions can reduce the life of the motor. The additional

resistance of operating in water causes excess strain. Alter the gear ratio

by using a smaller pinion or larger spur gear. This will increase torque (and

motor life) when running in mud, deeper puddles, or any wet conditions

that will increase the load on the motor for an extended period of time.

WET CONDITIONS MAINTENANCE

• Drain any water that has collected in the tires by spinning them at high

speed. With the body removed, place the vehicle upside down and pull full

throttle for a few short bursts until the water has been removed.

CAUTION: Always keep hands, ﬁ ngers, tools and any loose or

hanging objects away from rotating parts when performing the

above drying technique.

• Remove the battery pack(s) and dry the contacts. If you have an air

compressor or a can of compressed air, blow out any water that may be

inside the recessed connector housing.

• Remove the tires/wheels from the vehicle and gently rinse the mud and

dirt off with a garden hose. Avoid rinsing the bearings and transmission.

NOTICE: Never use a pressure washer to clean your vehicle.

• Use an air compressor or a can of compressed air to dry the vehicle and

help remove any water that may have gotten into small crevices or corners.

• Spray the bearings, drive train, fasteners and other metal parts with a

water-displacing light oil. Do not spray the motor.

• Let the vehicle air dry before you store it. Water (and oil) may continue

to drip for a few hours.

• Increase the frequency of disassembly, inspection and lubrication of the

following:

- Front and rear axle hub assembly bearings.

- All transmission cases, gears and differentials.

- Motor—clean with an aerosol motor cleaner and re-oil the bushings

with lightweight motor oil.

WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS

TABLE OF CONTENTS

Water-resistant Vehicle with Waterproof Electronics ..................................... 3

box Contents ............................................................................................................4

Required Equipment ............................................................................................... 4

recommended tools ................................................................................................ 4

Getting started checklist........................................................................................5

Vehicle parts ............................................................................................................ 5

Charge the vehicle battery .................................................................................... 6

Install the transmitter batteries ............................................................................ 6

Transmitter functions ............................................................................................. 6

Install the vehicle battery ...................................................................................... 7

Binding ......................................................................................................................8

Range-checking the radio system ....................................................................... 8

Using the DIG transmission ................................................................................... 8

vehicle maintenance ..............................................................................................9

AE-5L Forward/reverse ESC with drag brake ..................................................10

Troubleshooting .....................................................................................................10

Notes .......................................................................................................................11

Limited Warranty ................................................................................................... 12

Warranty and Service Contact Information .....................................................12

FCC Information ..................................................................................................... 13

IC Information ........................................................................................................13

Compliance Information for the European Union ............................................ 13

Exploded Views .....................................................................................................50

Parts Lists ............................................................................................................... 54

Electronics ............................................................................................................ 55

BOX CONTENTS

• Parts Bag

• Cross Wrench

• (4) AA Alkaline batteries

• Hex Drivers

(1.5, 2.0, 2.5mm)

• Hobby

Knife

• Side Cutter • Curved

Scissors

• Long-nose Plier

REQUIRED EQUIPMENT

RECOMMENDED TOOLS

• Battery charger compatible with

the chosen vehicle battery

• 2-3S Shorty LiPo Battery

(96mm maximum width, IC3

™

Connector Required)

• STX3

™

3Ch 2.4GHz FHSS Radio Transmitter (SPMSTX300)

• (4) AA Alkaline batteries

• Capra

™

1.9 Unlimited Trail Buggy RTR

- 35T Electric Motor (AX31312)

- SRX300 3CH Receiver (SPMSRX300)

- S614 Metal Gear Servo 23T WP (SPMS614)

- AE-5L ESC w/LED Ports and Lights

(DYNS2213)

Steering Servo

Steering Knuckle

Battery Tray

Transmission

Driveshaft

Upper 4-link Bar

ESC Plug

Electronic Speed Control (ESC)

Motor

Lower 4-link Bar

Shock Absorber

VEHICLE PARTS

GETTING STARTED CHECKLIST

Read the manual

Familiarize yourself with the vehicle and its components

Check all screws, especially the driveshaft setscrews, for tightness

from the factory

Charge the vehicle battery

Install 4 AA batteries in the transmitter

Power on the transmitter

Install the vehicle battery in the vehicle

Check for proper function of the throttle and steering

Range check the radio system

Drive the vehicle, challenge yourself and have FUN!

Perform any necessary vehicle maintenance

Steering Link

Dig Servo

Locked Differential

(inside axle housing)

Receiver Box

INSTALL THE TRANSMITTER BATTERIES

TRANSMITTER FUNCTIONS

This transmitter requires 4 AA batteries.

1. Remove the battery cover from the transmitter.

2. Install the batteries as shown.

3. Install the battery cover.

CAUTION: NEVER remove the transmitter batteries while the model

is powered on. Loss of model control, damage, or injury may occur.

CAUTION: If using rechargeable batteries, charge only rechargeable

batteries. Charging non-rechargeable batteries may cause the

batteries to burst, resulting in injury to persons and/or damage to property.

CAUTION: Risk of explosion if battery is replaced by an incorrect

type. Dispose of used batteries according to national regulations.

2.4GHZ DIGITAL

RADIO SYSTEM

Top

Bottom

A. Servo Reversing

To reverse the Throttle (TH) or Steering (ST) channel, switch the position

of the correlating switch—“N” is for normal, “R” is for reverse.

B. Throttle Trim

Adjusts the throttle neutral point

C. Steering Trim

Adjusts the steering center point. Normally, the steering trim is adjusted

until the vehicle tracks straight.

D. Throttle Rate

Adjusts the end point of the throttle

E. Steering Rate

Adjusts the end point of the steering

F. Indicator Lights

• Solid red lights: Indicates radio connectivity and adequate battery

power

• Flashing red lights: Indicates the battery voltage is critically low.

Replace batteries

G. Throttle Limit

Limits throttle output to 50/75/100%

Select 50% or 75% for less experienced drivers or when you are driving

the vehicle in a small area.

H. Antenna

I. Power Button

J. Throttle/Brake

K. Steering Wheel

L. Channel 3 Buttons: Top and Bottom

Follow the manufacturer’s directions for your charger to properly charge

the vehicle battery.

CAUTION: Only use chargers designed to charge the chosen

battery type. Using an incompatible charger or incorrect charge

settings could result in ﬁ re causing person injury or property damage.

CHARGE THE VEHICLE BATTERY

SETTING TRAVEL ENDPOINTS FOR CHANNEL 3

Follow the instructions below to set the travel endpoint of an accessory or servo on channel 3 if needed:

1. Press and hold the CH 3 “Top” button, while powering ON the

transmitter. Continue to hold the Top button until the transmitter LED

ﬂ ashes 5 times.

2. Release the Top button

3. Use the CH3 Top and Bottom buttons to adjust the accessory or servo

to the desired ﬁ rst end point position.

4. Turn the steering wheel fully clockwise (right) to conﬁ rm the ﬁ rst position.

The LED will ﬂ ash once to conﬁ rm the ﬁ rst position has been saved.

5. Use the CH3 Top and Bottom buttons to adjust the accessory or servo

to the desired second end point position.

6. Turn the steering wheel clockwise (right) to conﬁ rm the second

position. The LED will ﬂ ash twice to conﬁ rm the second position has

been saved.

7. Power off the transmitter to save the settings

NOTICE: Power to the vehicle is controlled by connecting and

disconnecting the battery from the ESC. Always power on the transmitter

ﬁ rst before connecting the vehicle battery. Always disconnect the

battery from the ESC when not in use.

2. Remove the body clips and open the hood.

3. Connect the battery to the ESC. Close the

hood and replace the body clips.

NOTICE: Always disconnect the battery from

the ESC before powering off the transmitter.

Powering off the transmitter ﬁ rst may result in

loss of control.

1. Power on the transmitter.

INSTALL THE VEHICLE BATTERY

BINDING

Bind Port

Ch 3 Top

Ch 3 Bottom

The radio system should be checked before operating the vehicle to ensure proper operation and adequate range.

1. Turn on the transmitter.

2. Connect the battery in the vehicle.

3. Have a friend hold the vehicle while keeping hands and loose clothing away from moving parts.

4. Walk away until you are at the maximum planned operating distance from the vehicle.

5. Turn the steering wheel side to side and operate the throttle, both forward and reverse, checking for any erratic behavior.

6. If any erratic behavior is exhibited, DO NOT operate the vehicle. Call customer service for assistance.

RANGE-CHECKING THE RADIO SYSTEM

Binding is the process of programming the receiver to recognize the

GUID (Globally Unique Identiﬁ er) code of a single speciﬁ c transmitter. The

STX3™ transmitter and SPMSRX300 receiver are bound at the factory. If

you need to rebind, follow the instructions below.

1. Insert the bind plug in the BIND port on the receiver.

2. Connect a fully charged battery pack to the ESC.

3. Power on the ESC. The red receiver LED ﬂ ashes, indicating the

receiver is in bind mode.

4. Center the ST TRIM and TH TRIM dials on the transmitter.

5. Turn and hold the steering wheel fully right, then power the transmitter

on.

6. When the receiver LED stops ﬂ ashing, release the steering wheel.

7. Remove the bind plug, then power off the receiver to save the settings.

8. Power off the transmitter.

9. Store the bind plug in a convenient place.

You must rebind when:

• Different failsafe positions are desired e.g., when throttle or steering

reversing has been changed.

• Binding the receiver to a different transmitter.

The Axial Capra includes a “Dig” transmission which allows the rear

axle to lock while still allowing the front wheels to spin. Use this feature

in close quarters to turn the vehicle tighter than is possible with normal

4 wheel drive or to preload the suspension when needed.

To use the Dig function:

1. Press the channel 3 “Top” button on the transmitter. The Dig function

engages, locking the rear axle.

2. Advance the throttle and turn the steering wheel left or right to tightly

pivot the vehicle around.

3. Press the channel 3 “Bottom” button to disengage the Dig function.

USING THE DIG TRANSMISSION

Replace any

noticeable bent or

broken parts

Check the wheel nuts

for tightness

If applicable, check

the slipper clutch for

proper operation

Check for wear on

the ball joints in

the steering and

suspension links

(replace if necessary)

Ensure the wheel

beads are still ﬁ rmly

bonded around the

entire circumference

of the rim

Check the receiver

antenna for damage

Check driveshaft

set screws and

apply thread

locking compound if

necessary

Keep the chassis free

of dirt and debris

Check the steering

operation for any

binding

Inspect shock

absorbers for smooth

dampened operation

Check for loose

screws on the chassis,

especially the knuckle,

C-hub and axle lockout

screws

Inspect the spur

and pinion gears for

damage

Check for any loose

connections or frayed

wiring

Check the driveline

for smooth, bind free

operation

Replace the

transmitter batteries

when indicated by

the transmitter, as

described in the

Transmitter Functions

section

Just like a full size car or truck your RC vehicle must undergo periodic maintenance in order to ensure peak performance. Preventative maintenance will

also help avoid needless breakages which could result in costly repairs. Below are some suggestions to properly maintain your vehicle.

VEHICLE MAINTENANCE

TROUBLESHOOTING

Battery ESC

Red

Black

Motor

PROBLEM POSSIBLE CAUSE SOLUTION

Vehicle does not move

Batteries are not installed properly in the

transmitter

Ensure the transmitter batteries are properly installed

Weak or no battery in the vehicle Install a freshly charged vehicle battery

Damaged motor Replace the motor

Frayed or broken wiring Replace any damaged wiring

ESC is shut down by heat protection circuit Allow the ESC to cool down completely

Loss of vehicle control

Improper antenna placement

Ensure the transmitter antenna is not blocked and the receiver

antenna is located properly

Weak or no batteries in the transmitter or

vehicle

Install a freshly charged vehicle battery and new transmitter

batteries

Neutral or trim position is incorrect Adjust the steering trim

Receiver and/or battery not connected

properly

Check all receiver and battery connections

Steering and/or throttle function is reversed

Servo travel is reversed at the transmitter Set the transmitter servo reversing switch to the correct position

Motor wires are not connected properly Check all motor wires for correct polarity and secure connection

AE-5L FORWARD/REVERSE ESC WITH DRAG BRAKE

SETUP

Throttle calibration should not be needed out of the box. However, in order

to make the throttle range of different transmitters, the calibration of the

ESC is necessary:

• Mount the ESC in an area that is well ventilated and isolated from

vibration and shock.

• Connect the ESC motor wires to the motor red-to-red and black-to-black.

• Plug the receiver into the throttle channel of the receiver.

• Before plugging the battery into the ESC, make sure your transmitter is

on and the throttle trim is set to zero.

• Connect the battery to the ESC. The vehicle will be powered on when the

battery is connected.

CAUTION: Keep all body parts and loose clothing away from any

moving parts while the battery is connected to the ESC.

CAUTION: Always connect the ESC only to a proper power

source that has the correct voltage and polarity. Incorrect

voltages or reversed polarity will damage the ESC. Damage to the ESC

caused by improper voltage or polarity is not covered under warranty.

• Test forward and reverse control using the transmitter.

To calibrate the ESC:

• Power the transmitter on and set the throttle control to neutral.

• Connect the battery to the ESC and wait 3 seconds to let the ESC initiate

a self-test and automatic throttle calibration.

• The ESC is ready to run when a long beep sound is emitted from the motor.

• Always disconnect the battery when the vehicle is not in use.

NOTES

• The drag brake is set to 100% from the factory.

• The LiPo cut-off is set to “ON” from the factory.

ESC SPECIFICATIONS

Input Voltage 2-3S LiPo, 5-9 Cells NiMH/NiCd

Size 46.5mm x 34mm x 28.5mm

Weight 70g

Motor Limit 12T 2S/18T 3S

On-Resistance FET .002

Rated/Peak Current 180A

Braking Current 90A

BEC Voltage/A 6.0V 3.0A Peak

PWM Frequency 1KHz

ESC SOUND STATUS

1 Short Beep Battery is NiMH/NiCd

2 Short Beeps Battery is 2S LiPo

3 Short Beeps Battery is 3S LiPo

1 Long Beep

Self-test and throttle calibration

is OK and ESC is ready to run

To Receiver

Throttle Channel

NOTES

What this Warranty Covers

Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the

product purchased (the “Product”) will be free from defects in materials

and workmanship for a period of 2 years from the date of purchase.

What is Not Covered

This warranty is not transferable and does not cover (i) cosmetic damage,

(ii) damage due to acts of God, accident, misuse, abuse, negligence,

commercial use, or due to improper use, installation, operation or

maintenance, (iii) modiﬁ cation of or to any part of the Product, (iv) attempted

service by anyone other than a Horizon Hobby authorized service center, (v)

Product not purchased from an authorized Horizon dealer, or (vi) Product not

compliant with applicable technical regulations or (vii) use that violates any

applicable laws, rules, or regulations.

OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO

OTHER WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS

ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT

LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE

PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED

THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE

PURCHASER’S INTENDED USE.

Purchaser’s Remedy

Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall

be that Horizon will, at its option, either (i) service, or (ii) replace, any

Product determined by Horizon to be defective. Horizon reserves the right

to inspect any and all Product(s) involved in a warranty claim. Service

or replacement decisions are at the sole discretion of Horizon. Proof of

purchase is required for all warranty claims. SERVICE OR REPLACEMENT

AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER’S SOLE AND

EXCLUSIVE REMEDY.

Limitation of Liability

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL

OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION

OR COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH

CLAIM IS BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT

LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS

BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in

no event shall the liability of Horizon exceed the individual price of the

Product on which liability is asserted. As Horizon has no control over use,

setup, ﬁ nal assembly, modiﬁ cation or misuse, no liability shall be assumed

nor accepted for any resulting damage or injury. By the act of use, setup

or assembly, the user accepts all resulting liability. If you as the purchaser

or user are not prepared to accept the liability associated with the use of

the Product, purchaser is advised to return the Product immediately in new

and unused condition to the place of purchase.

Law

These terms are governed by Illinois law (without regard to conﬂ ict of law

principals). This warranty gives you speciﬁ c legal rights, and you may also

have other rights which vary from state to state. Horizon reserves the right to

change or modify this warranty at any time without notice.

WARRANTY SERVICES

Questions, Assistance, and Services

Your local hobby store and/or place of purchase cannot provide warranty

support or service. Once assembly, setup or use of the Product has been

started, you must contact your local distributor or Horizon directly. This

will enable Horizon to better answer your questions and service you in

the event that you may need any assistance. For questions or assistance,

please visit our website at www.horizonhobby.com, submit a Product

Support Inquiry, or call the toll free telephone number referenced in the

Warranty and Service Contact Information section to speak with a Product

Support representative.

Inspection or Services

If this Product needs to be inspected or serviced and is compliant in the

country you live and use the Product in, please use the Horizon Online

Service Request submission process found on our website or call Horizon

to obtain a Return Merchandise Authorization (RMA) number. Pack the

Product securely using a shipping carton. Please note that original boxes

may be included, but are not designed to withstand the rigors of shipping

without additional protection. Ship via a carrier that provides tracking

and insurance for lost or damaged parcels, as Horizon is not responsible

for merchandise until it arrives and is accepted at our facility. An Online

Service Request is available at http://www.horizonhobby.com/content/

service-center_render-service-center. If you do not have internet access,

please contact Horizon Product Support to obtain a RMA number along

with instructions for submitting your product for service. When calling

Horizon, you will be asked to provide your complete name, street address,

email address and phone number where you can be reached during

business hours. When sending product into Horizon, please include

your RMA number, a list of the included items, and a brief summary of

the problem. A copy of your original sales receipt must be included for

warranty consideration. Be sure your name, address, and RMA number are

clearly written on the outside of the shipping carton.

NOTICE: Do not ship Li-Po batteries to Horizon. If you have any issue

with a Li-Po battery, please contact the appropriate Horizon Product

Support ofﬁ ce.

Warranty Requirements

For Warranty consideration, you must include your original sales receipt

verifying the proof-of-purchase date. Provided warranty conditions have

been met, your Product will be serviced or replaced free of charge.

Service or replacement decisions are at the sole discretion of Horizon.

Non-Warranty Service

Should your service not be covered by warranty, service will be completed

and payment will be required without notiﬁ cation or estimate of the

expense unless the expense exceeds 50% of the retail purchase cost. By

submitting the item for service you are agreeing to payment of the service

without notiﬁ cation. Service estimates are available upon request. You

must include this request with your item submitted for service. Non-

warranty service estimates will be billed a minimum of 1/2 hour of labor. In

addition you will be billed for return freight. Horizon accepts money orders

and cashier’s checks, as well as Visa, MasterCard, American Express,

and Discover cards. By submitting any item to Horizon for service, you are

agreeing to Horizon’s Terms and Conditions found on our website http://

www.horizonhobby.com/content/service-center_render-service-center.

ATTENTION: Horizon service is limited to Product compliant in the

country of use and ownership. If received, a non-compliant Product will

not be serviced. Further, the sender will be responsible for arranging

return shipment of the un-serviced Product, through a carrier of the

sender’s choice and at the sender’s expense. Horizon will hold non-

compliant Product for a period of 60 days from notiﬁ cation, after which

it will be discarded.

10/15

Country of Purchase Horizon Hobby Contact Information Address

United States of America

Horizon Service Center

(Repairs and Repair Requests)

servicecenter.horizonhobby.com/RequestForm/

2904 Research Rd

Champaign, IL 61822

Horizon Product Support

(Product Technical Assistance)

productsupport@horizonhobby.com

877-504-0233

Sales

websales@horizonhobby.com

800-338-4639

European Union

Horizon Technischer Service service@horizonhobby.eu

Hanskampring 9

D 22885 Barsbüttel, Germany

Sales: Horizon Hobby GmbH +49 (0) 4121 2655 100

LIMITED WARRANTY

WARRANTY AND SERVICE CONTACT INFORMATION

INSTRUCTIONS FOR DISPOSAL OF WEEE BY USERS IN THE EUROPEAN UNION

This product must not be disposed of with other waste. Instead, it is the user’s responsibility to dispose of their waste equipment by handing it

over to a designated collections point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of

your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects

human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your

local city ofﬁ ce, your household waste disposal service or where you purchased the product.

EU COMPLIANCE STATEMENT:

Axial Capra 1.9 (AXI03000)

Horizon Hobby, LLC hereby declares that this product is in compliance with the essential requirements and other relevant provisions of the RED

and EMC Directives.

A copy of the EU Declaration of Conformity is available online at: http://www.horizonhobby.com/content/support-render-compliance.

FCC INFORMATION

IC INFORMATION

COMPLIANCE INFORMATION FOR THE EUROPEAN UNION

CAN ICES-3 (B)/NMB-3(B)

IC: 6157A-STX3

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

FCC ID: BRWSTX3

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAUTION: Changes or modiﬁ cations not expressly approved by the party responsible for compliance could void the user’s authority to operate

the equipment.

This product contains a radio transmitter with wireless technology which has been tested and found to be compliant with the applicable regulations

governing a radio transmitter in the 2.400GHz to 2.4835GHz frequency range.

SUPPLIER’S DECLARATION OF CONFORMITY

Axial Capra 1.9 (AXI03000)

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAUTION: changes or modiﬁ cations not expressly approved by the party responsible for compliance could void the user’s authority to operate

the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Horizon Hobby, LLC

2904 Research Rd.,

Champaign, IL 61822

Email: compliance@horizonhobby.com

Web: HorizonHobby.com

EXPLODED VIEWS // EXPLOSIONSZEICHNUNGEN // VUES ÉCLATÉES // VISTE ESPLOSE

AXA232017

AXI232017

AXA0286

AX31148

AXA31028

AXA144

AXA31028

AXA0286

AX31148

AXI232017

AXI234003

AXI234006

AXI234004

AXI234008

AXI234009

AXI234008

AXI234006

AXI235016

AXI232004

AXA1221

AXA120

AXI234006

AXI234004

AX31407

AXI234004

AXI235109AXI234006

AXI232003

AXA0109

AXI234004

AXA120

AXI235109

AXI234009

AXA144

AXI234006

AXI232004

AXI234006

SPMS614

AXI234004

AXI234006

AXI234003

AXI234004

AXA118

AXI235109

AXI234006

AXI234004

AXI234005

AXI234006

AXI234004

AXI234006

AXI234004

AXA116

AXI234007

AXI234005

AXA115

AXI234006

AXI234004

AXI235004

AXI232006

AXA1221

AX31406

AXI232002

AX31406

AX31066

AXI235004

AXI232006

AXI237009

AXA1221

AXI232007

AXA1230

AXA1221

AX30165

AXI232008

AXI232006

AX31403

AXA1221

AXI232009

AXA1221

AXI232004

AXI232009

AX31403

AXI237009

AXI232008

AX30165

AXI232006

AXA1230

AXI232007

FRONT AXLE

VORDERACHSE

ESSIEU AVANT

ASSALE ANTERIORE

REAR AXLE

HINTERACHSE

ESSIEU ARRIÈRE

ASSALE POSTERIORE

AXI234003

AXI234008

AXI234009

AXI235014

AXI232005

AXA1221

AXI237009

AXI232007

AXI232008

AX30165

AXA120

AXI234004

AXI234006

AXI232010

AXA232017

AXA144

AXA31028

AXA0286

AX31148

AXI232017

AXA31028

AXI232017

AXA0286

AX31148

AXA1221

AXI235004

AXI232005

AXI237009

AXA1221

AXI232007

AXA1221

AXI232008

AXA1221

AXI234006

AXI235109

AXI234006

AXI234004

AX30165

AXI234006

AXI232010

AXI232005

AXI234004

AXI235016

AX31407

AXI235016

AXI234008

AXI234009

AXI234004

AX31406

AXI232007

AXI232002

AX31066

AXA120

AXI234006

AXI235109

AXI234004

AX31406

AXI234004

AXA1225

AXA31642

AXI232014

AXI237003

AXI232012

AXA1234

AXI232014

AXI232011

AXI232013

AXI232014

AXA1218

AXI232011

AXA144

AXA146

AXI232011

AX31250

AXA1218

AXA148

AXA144

AXI232014

AXI232013

AXA1218

AX31312

AXI232012

AXI236175

AXA1218

AXI232013

AXA291

AX30569

AXA0109

AXI232015

AXI232011

AXI232012

TRANSMISSION

GETRIEBE

TRANSMISSION

TRASMISSIONE

CHASSIS

KAROSSERIE

CHÂSSIS

TELAIO

AXI231006

AXI230012 (Clear)

AXA113

AXI230011 (Clear)

AXA114

AXI230011 (Clear)

AXI230011

AXI235330

AXI235109

AXA146

AXA144

AXI235109

AXI231005

AXI232011

AXA116

AXI232016

AX31066

AXI235169

AX31066AXA116

AXI232016

SPMSSX107

AXI232016

CHASSIS

KAROSSERIE

CHÂSSIS

TELAIO

AXI235097 AXI230012 (Clear)

AXA116

AXA118

AXA120

AXA118

AXI235097

AXI230012 (Clear)

AXI235269

AXI231006

AXA118

AXI231006

AXA114

AXA116

AXI231006

AXI235097

AXI231006

AXI235097

AXI231006

AXI235098

AXA114

AXI231006

AXI235098

AXA118

AXI231006

AXA118

AXI235097

AXI231006

AXA118

DYNS2213

SPMSRX300

AXA116

AXA118

AXI231006

AXA115

AXA118

AXI230010

AXA231006

AXI235102

AXA120

AXA116

AXA118

AXI230012 (Clear)

SHOCK ABSORBERS

STOSSDÄMPFER

AMORTISSEURS

AMMORTIZZATORI

WHEELS AND TIRES

REIFEN UND RÄDER

ROUES ET PNEUS

RUOTE E PNEUMATICI

AXA1059

AXI231006

AXI236172

AXI232018

AXA114

AXI43004

AX31250

AXI43004

AX31565

AXI235099

AXI233002

AXI233006

AXI233002

AXI233003

AXI233001

AXA1392

AXI233002

AXI233003

AXI233000

AXI235094

AXI233002

PARTS LISTS // TEILELISTEN // LISTE DES PIÈCES // ELENCO COMPONENTI

Part # Description Beschreibung Description Descrizione

AXI230010 Head Light Lens

Scheinwerferlinse Lentilles de phares Lenti per faro

AXI230011 Interior Set

Interieurset Ensemble d’intérieur Set interni

AXI230012 Body Panel Set (Clear)

Karosserieteilesatz, farblos

Ensemble de panneaux de carrosserie,

transparent

Set pannelli carrozzeria, trasparente

AXI231005 Skid Plate

Motorschutz Plaque de protection Piastra di protezione

AXI231006 UTB Cage Set Complete

Überrollkäﬁ gset, komplett Ensemble de cages complet Set scocca completo

AXI232002 6-Bolt Differental Locker

6-Schrauben-Differenzial-Sicherung Blocage différentiel à 6 boulons Blocco differenziale 6 bulloni

AXI232003 6 Bolt Heavy Duty Gear Set

6-Schrauben-Schwerlast-Zahnradsatz

Ensemble d’engrenages haute résistance à

6 boulons

Set ingranaggio impieghi gravosi 6 bulloni

AXI232004 F9 Portal Axl housing FR

Currie F9-Portalachsgehäuse, vorne Carter d’essieu du portique Currie F9, avant

Currie F9 Portal, alloggiamento assale,

anteriore

AXI232005 F9 Portal Axl housing RR

Currie F9-Portalachsgehäuse, hinten Carter d’essieu du portique Currie F9, arrière

Currie F9 Portal, alloggiamento assale,

posteriore

AXI232006 F9 Portal Str knucl & Cap

Currie F9 Portal-Achsschenkel und -abdeckung

Rotule de direction et coiffe du portique Currie

F9, arrière

Currie F9 Portal, fuso a snodo e tappo

AXI232007 32P Portal Gr Set 23T/12T 2pc

32P Portalachssatz 23T/12T (2) Ensemble engrenage portique 32P 23T/12T (2) Set ingranaggi 32P Portal 23T/12T (2)

AXI232008 Portal Stub Axle (2)

Portalachsschenkel (2) Demi-essieu du portique (2) Fusello Portal (2)

AXI232009 F9 Universal Axle Set (2pc)

Currie F9-Universalachsset (2) Ensemble d’essieux universels Currie F9 (2) Currie F9, set assale universale (2)

AXI232010 F9 Straight Axle Shaft 2pc

Currie F9, Gerade Achswelle (2) Ensemble d’essieux droits Currie F9 (2) Currie F9, set assale dritto (2)

AXI232011 Dig Transmission Case Set

Grabgetriebe-Abdeckungssatz Ensemble boîtier de transmission dig Set scatola cambio dig

AXI232012 Dig Trans Metal Gear Set

Grabgetriebe-Metallgetriebesatz

Ensemble d’engrenages métalliques de

transmission dig

Set ingranaggi trasmissione dig in metallo

AXI232013 Dig Transmission Shaft Set

Grabgetriebewellensatz Ensemble d’arbres de transmission dig Set albero trasmissione dig

AXI232014 Dig Trans Dig Cmpnts

Grabgetriebe, „Grab“-komponenten Composants « dig » transmission dig Componenti trasmissione dig

AXI232015 Dig Trans Slipper Pads/Plts

Grabgetriebe-Gleitschuhe/-platten

Sabots de pistons/plaques de sabot de

transmission dig

Piastre/pattini di scorrimento trasmissione dig

AXI232016 Dig Trans Mnts&Srvo Svr Set

Grabgetriebe-Halterungen und Servo-

Saversatz

Ensemble supports et économiseur de servo

de transmission dig

Set salvaservo e supporti trasmissione dig

AXI232017 Wild Boar Driveshaft Set

Wild Boar-Antriebswellensatz Ensemble d’arbres de transmission Wild Boar Set albero di trasmissione Wild Boar

AXI232018 12mm Hex Pin and Spacer (4)

12-mm-Sechskantstift und Abstandhalter (4) Broche hexagonale 12mm et entretoise (4) Distanziale e perno esagonale 12mm (4)

AXI233000 Thrd AL Shk Bdy 11x41.5mm HA 2pc

Gewinde-Aluminium-Stoßdämpfergehäuse

11x41,5mm HA (2)

Carrosserie d’amortisseurs en aluminium ﬁ leté

11x41,5mm HA (2)

Scocca ammortizzatore ﬁ lettata in alluminio

11x41,5mm HA (2)

AXI233001 Shock Shaft M3x53.4 (2pcs)

Kolbenstange M3 x 53,4 mm (2) Bras d’amortisseur M3x53,4mm (2) Albero ammortizzatore M3x53,4mm (2)

AXI233002 Shock Prts Molded

Stoßdämpferteile, gegossen Pièces de l’amortisseur moulées Parti ammortizzatore stampate

AXI233003 Shock O-Ring Set

O-Ring-Satz für den Stoßdämpfer Ensemble de joints toriques d’amortisseur Set O-Ring ammortizzatore

AXI233004 Spring 13x70mm .72lbs/in Prpl(2)

Feder 13x70mm 0,72 lbs/in (326 g/Zoll), violett (2) Ressort 13x70mm 0,72lbs/po, violet (2)

Molla 13x70mm 0,72lbs/in (326 g/pollice), viola (2)

AXI233006 Spring 13x70mm 1.72lbs/in Red(2)

Feder 13x70mm 1,72 lbs/in (780 g/Zoll), rot (2) Ressort 13x70mm 1,72lbs/po, rouge (2)

Molla 13x70mm 1,72lbs/in (780 g/pollice), rosso (2)

AXI233008 Spring 13x70mm 2.4lbs/in Grn(2)

Feder 13x70mm 2,4 lbs/in (1,08 kg/Zoll), grün (2) Ressort 13x70mm 2,4lbs/po, vert (2)

Molla 13x70mm 2,4lbs/in (1,08 kg/pollice), verde (2)

AXI234003 Pvt Ball,Stainless12.75mm(4)

Kugelzapfen, Edelstahl 12,75 mm (4) Rotule, acier inoxydable 12,75mm (4) Pivot ball, inossidabile, 12,75mm (4)

AXI234004 Susp Pvt Ball, Stainless 7.5mm

Kugelzapfen für Federung, Edelstahl 7,5 mm Rotule de suspension, acier inoxydable 7,5mm Pivot ball sospensioni, indossabile, 7,5mm

AXI234005 Steering Lnks Stainless Stl

Spurstangen, Edelstahl Tringleries de direction, acier inoxydable Tiranti sterzo, inossidabili

AXI234006 HD Rod Ends M4 20pcs

Schwerlast-Stangenköpfe M4 (20) Embouts de bielle haute résistance M4 (20) Teste a snodo per impiego gravoso M4 (20)

AXI234007 SS M6x 111mm Link (2pcs)

Edelstahlglied M6 x 111 mm (2) Liaison en acier inoxydable M6x111mm (2) Braccetti in acciaio inossidabile M6x111mm (2)

AXI234008 SS M6x 111mm Link (2pcs)

Edelstahlglied M6x111mm (2) Liaison en acier inoxydable M6x111mm (2) Braccetti in acciaio inossidabile M6x111mm (2)

AXI234009 Stainless Steel M6 x 89mm Link

Edelstahlglied M6x89mm (2) Liaison en acier inoxydable M6x89mm (2) Braccetti in acciaio inossidabile M6x89mm (2)

AXI235014 M2.5 x 10mm, Cap Head Screw (10)

Inbusschraube, M2,5x10mm (10) Vis d’assemblage creuse, M2,5x10mm (10) Vite a testa cilindrica M2,5x10mm (10)

AXI235016 M2.5 x 16mm, Cap Head Screw (10)

Inbusschraube, M2,5x16mm (10) Vis d’assemblage creuse, M2,5x16mm (10) Vite a testa cilindrica M2,5x16mm (10)

AXI235094 M2.5 x 3mm, Button Head (10)

Rundkopfschraube, M2,5x3mm (10) Vis à tête bombée, M2,5x3mm (10) Vite a testa tonda M2,5x3mm (10)

AXI235097 M2.5 x 6mm, BHS (10)

Rundkopfschraube, M2,5x6mm (10) Vis à tête bombée, M2,5x6mm (10) Vite a testa tonda M2,5x6mm (10)

AXI235098 M2.5 x 8mm Button Head Screw(10)

Rundkopfschraube, M2,5x8mm (10) Vis à tête bombée, M2,5x8mm (10) Vite a testa tonda M2,5x8mm (10)

AXI235099 M2.5 x 10mm, Button Head (10)

Rundkopfschraube, M2,5x10mm (10) Vis à tête bombée, M2,5x10mm (10) Vite a testa tonda M2,5x10mm (10)

AXI235102 M2.5 x 18mm, BHS (10)

Rundkopfschraube, M2,5x18mm (10) Vis à tête bombée, M2,5x18mm (10) Vite a testa tonda M2,5x18mm (10)

AXI235109 M3 x 14mm, Button Head Screw(10)

Rundkopfschraube, M3x14mm (10) Vis à tête bombée, M3x14mm (10) Vite a testa tonda M3x14mm (10)

AXI235169 M2.5 x 12mm, Flat Head Screw(10)

Flachkopfschraube, M2,5x12mm (10) Vis à tête plate, M2,5x12mm (10) Vite a testa piana M2,5x12mm (10)

AXI235330 M3x30mm,Cup Point Set Screw (10)

Stellschraube mit Ringschneide M3x30mm (10) Vis de ﬁ xation à bout cuvette M3x30mm (10) Vite di fermo senza testa M3x30mm (10)

AXI236171 M2.5 x 10mm Pin (6)

Stift M2,5x10mm (6) Axe M2.5x10 mm (6) Perno M2,5x10mm (6)

AXI236172 Screw Shaft M3x2.0x12mm

Schraubenschaft M3x2x12mm Tige de vis M3x2x12 mm Albero ﬁ lettato M3x2x12mm

AXI43004 3pc Raceline Mnstr bdlk whl (2)

3x Raceline Monster Beadlock-Rad (2) 3 pièces de verrou de talon Raceline Monster (2) Cerchio Beadlock Raceline Monster in 3 pezzi (2)

AXIC0012 AXA120 Hex Socket Btn Hd M3x25mm

Sechskant-Rundkopfschraube M3x25mm Douille à six pans à tête bombée M3x25mm

Vite a testa tonda con esagono incassato M3x25mm

Part # Description Beschreibung Description Descrizione

AXIC0013 AXA013 Cap Hd M2x6mm Blk Oxide

Inbusschraube, M2x6mm, Schwarzoxid Vis d’assemblage creuse M2x6mm brunie Vite a testa cilindrica M2x6mm ossido nero

AXIC0115 AXA115 Hex Skt Butn Head M3x10mm

Sechskant-Rundkopfschraube, M3x10mm Douille à six pans à tête bombée M3x10mm

Vite a testa tonda con esagono incassato

M3x10mm

AXIC0118 AXA144 Hex Flt Hd M3x8mm Blk10mm

Sechskant-Flachkopfschraube, M3x8mm, schwarz (10) Douille à six pans à tête plate M3x8mm noire (10) Vite a testa piana esagonale M3x8mm nero (10)

AXIC0146 AXA146 Hex Skt Flat Hd M3x12mm

Sechskant-Flachkopfschraube, M3x12mm Douille à six pans à tête plate M3x12mm

Vite a testa piana con esagono incassato M3x12mm

AXIC0218 AXA1218 Bearing 5x10x4mm

Lager 5x10x4mm Roulement 5x10x4mm Cuscinetto 5x10x4mm

AXIC0221 AXA1221 Bearing 5x11x4mm

Lager 5x11x4mm Roulement 5x11x4mm Cuscinetto 5x11x4mm

AXIC0286 AXA0286 Screw Shaft M4x2.5x12mm

Schraubenschaft M4x2,5x12 mm Tige de vis M4x2,5x12mm Albero ﬁ lettato M4x2.5x12mm

AXIC0291 AXA291 Set Scr M4x4mm Blk Ox(6)

Stellschraube, M4x4mm, Schwarzoxid (6) Vis de ﬁ xation M4x4mm brunie (6) Vite di fermo M4x4 mm ossido nero (6)

AXIC0795 AX31586 Wb8-hd Std Driveshafts

WB8-HD Standard-Antriebswelle Arbre de transmission standard WB8-HD Albero di trasmissione standard WB8-HD

AXIC1009 AXA0109 Hex Skt Oversize M3x10mm

Sechskant-Übergröße M3x10mm Douille à 6 pans surdimensionnée M3x10mm Viti oversize con esagono incassato M3x10mm

AXIC1148 AX31148 Wb8-hd Drvshft Coupler

WB8-HD-Antriebswellenkupplung

Ensemble de couplage d’arbre de transmission

WB8-HD

Accoppiamento albero trasmissione WB8-HD

AXIC1180

AXA118 Hex Socket BtnHd

M3x18mm(10)

Sechskant-Rundkopfschraube M3x18mm (10) Douille à six pans à tête bombée M3x18mm (10)

Viti a testa tonda con esagono incassato

M3x18mm (10)

AXIC1243 AXA1243 Bearing 15x21x4mm (2)

Lager 15x21x4mm (2) Roulement à billes 15x21x4mm (2) Cuscinetto 15x21x4mm (2)

AXIC3066 AX31066 Cap Hd M2x8mm Blk (10)

Inbusschraube M2x8mm, schwarz (10) Vis d’assemblage creuse M2x8mm noire (10) Vite a testa cilindrica M2x8mm nero (10)

AXIC3150 AX31250 Ser Nyl Nut Blk 4mm(10)

Nylon-Feststellﬂ anschmutter, 4mm (10) Contre-écrou en nylon strié 4mm (10) Dato ﬂ angiato Nylock nero 4mm (10)

AXIC3165 AX30165 Pin 2.5x12mm (6)

Stift 2,5x12mm (6) Axe M2,5x12mm (6) Perno 2,5x12mm (6)

AXIC4406 AX31406 Bearing 7x14x3.5mm (2)

Lager 7x14x3,5mm (2) Roulement 7x14x3,5mm (2) Cuscinetto 7x14x3,5mm (2)

AXIC4407 AX31407 Bearing 5x14x5mm (2)

Lager 5x14x5mm (2) Roulement 5x14x5 mm (2) Cuscinetto 5x14x5mm (2)

AX31565

1.9" Nitto Trail Grappler Monster

Truck R35 Compound Tire (2)

1,9Zoll Nitto Trail Grappler Monster-Truck

R35 Compound Reifen (2)

Pneu 1.9" Nitto Trail Grappler Monster

Truck R35 Compound (2)

Pneumatico compound 1.9" Nitto Trail

Grappler Monster Truck R35 (2)

DYNS2213 WPAE-5L Brshd ESC LED Port w/IC3

WPAE-5L gebürsteter Geschwindigkeitsregler

LED-Anschluss mit IC3

Port DEL de variateur ESC à balais WPAE-

5L avec IC3

ESC con spazzole WPAE-5L porta LED con

IC3

SPMS614 S614 Metal Gear Servo 23T WP S614 Metallgetriebeservo 23T WP

Servo à engrenages métalliques S614, 23

dents, étanche

Servo con ingranaggi in metallo S614 23T

SPMSRX300 SRX300 3CH Receiver SRX300 3CH Empfänger Récepteur 3 canaux SRX300 Ricevitore SRX300 3 canali

SPMSSX107 SX107 Micro Metal Gear Servo SX107 Mikro-Metallgetriebeservo Micro servo à engrenages métalliques SX107 Micro servo con ingranaggi in metallo SX107

SPMSTX300 Stx 3Ch 2.4 Ghz Fhss Radio Sys Stx 2,4Ghz Fhss-Funksys Mit 3 Kan Système Radio Stx 3Canaux 2,4Ghz Fhss Sistema Radio Fhss Stx 3 Ch 2,4 Ghz

Part # Description Beschreibung Description Descrizione

AX31312 35T Electric Motor 35T Elektromotor Moteur électrique 35T Motore elettrico 35T

SPMSTX300 STX3 3CH Radio STX3 3CH Sender Radio 3 canaux STX3 Radiocomando STX3 3 canali

SPMSRX300 SRX300 3CH Receiver SRX300 3CH Empfänger Récepteur 3 canaux SRX300 Ricevitore SRX300 3 canali

SPMS614 S614 Metal Gear Servo 23T WP S614 Metallgetriebeservo 23T WP

Servo à engrenages métalliques S614, 23

dents, étanche

Servo con ingranaggi in metallo S614 23T

SPMSSX107 SX107 Micro Metal Gear Servo SX107 Mikro-Metallgetriebeservo Micro servo à engrenages métalliques SX107 Micro servo con ingranaggi in metallo SX107

DYNS2213

AE-5L ESC w/LED Ports and Lights

(2 White, 4 White, 2 Red)

AE-5L Geschwindigkeitsregler mit LED-

Anschlüssen und -Leuchten

(2 x weiß, 4 x weiß, 2 x rot)

Variateur ESC AE-5L avec ports et témoins

DEL (2 blancs, 4 blancs, 2 rouges)

ESC AE-5L con porte e luci LED

(2 bianche, 4 bianche, 2 rosse)

ELECTRONICS // ELECTRONIK // COMPOSANTS ÉLECTRONIQUES // ELETTRONICA

Axial, the Axial logo, Capra, DSM, STX3, IC3 and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC.

The Spektrum trademark is used with permission of Bachmann Industries, Inc. Nitto

and Trail Grappler

are registered trademarks of Nitto Tire U.S.A., Inc.

The CRC name and logo are trademarks or registered trademarks of Casey Currie Motorsports. The Raceline Wheels name and logo are trademarks or registered

trademarks of Allied Wheel Components, Inc. All other trademarks, service marks and logos are property of their respective owners.

Completed 11/19 AXI03000 59181.1

facebook.com/axialinc | instagram.com/axialracing | twitter.com/axialrc

youtube.com/axialvideos | ﬂ ickr.com/axialrc

OFFICIALLY LICENSED BY:

AXI03000