Rinnai RHFE-265FTA-2A-N Mode d'emploi

Direct Vent Wall Furnace

Installation and Operation Manual

EX08CT............... (RHFE-202FTA2)

EX11CT ............... (RHFE-265FTA2)

Installer: Leave this manual with the appliance.

Consumer: Retain this manual for future reference.

— Do not store or use gasoline or other ammable vapors and liquids in the vicinity of this or any other

appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instrucons.

• If you cannot reach your gas supplier, call the re department.

— Installaon and service must be performed by a licensed professional.

If the informaon in these instrucons is not followed exactly, a re or explosion

may result causing property damage, personal injury or death.

WARNING

READ ALL OF THE INSTRUCTIONS THOROUGHLY BEFORE INSTALLING OR OPERATING

THIS HEATER.

This manual provides information on the installation, operation, and maintenance of the heater. For

proper operation and safety, it is important to follow the instructions and adhere to the safety

precautions.

A licensed professional must install the fan convection heater according to the exact instructions

within this manual.

The consumer must read the entire manual to properly operate the heater and to have regular

maintenance performed.

Register your product at www.rinnairegistration.com or call 1-866-RINNAI1 (746-6241)

2 Rinnai Corporation EX08CT, EX11CT Manual

Table of Contents

Important Safety Information

Safety Definitions

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and

others.

Indicates an imminently hazardous situation which, if not avoided, will result in death or

serious injury.

Indicates a potentially hazardous situation which, if not avoided, could result in death or

serious injury.

Indicates a potentially hazardous situation which, if not avoided, could result in minor or

moderate injury. It may also be used to alert against unsafe practices.

DANGER

CAUTION

WARNING

NOTICE: Rinnai sometimes shares customer contact information with businesses that we believe provide

products or services that may be useful to you. By providing this information, you agree that we can

share your contact information for this purpose. If you prefer not to have your information shared with

these businesses, please contact customer service and ask not to have your information shared. We will

however, continue to contact you with information relevant to the product(s) you registered and/or your

account with us.

If you have any questions or feel that the manual is incomplete contact Rinnai at 1-800-621-9419.

Table of Contents ............................................. 2

Safety Definitions ............................................. 2

Safety Behaviors and Practices for the Consumer

and Installer ...................................................... 3

Installation Instructions

(for the licensed professional)

State Regulations ............................................. 4

Included Installation and Vent Components .... 5

Installation Instructions..................................... 6

Prepare for Installation ..................................... 7

Determine Installation Location ........................ 7

Flue Terminal Clearances ................................ 8

Clearances to Combustibles ............................ 9

Checklist to Determine Installation Location .... 9

Drilling Flue Hole ............................................ 10

Flue Manifold Installation ............................... 10

Extension Kit Installation ................................ 12

Connecting the Appliance .............................. 15

Gas Connection ............................................. 16

Adjust Gas Pressure Settings ........................ 16

Dimensions .................................................... 20

Specifications ................................................. 21

Direct Vent Furnace Operation Instructions

Safe Operation .............................................. 23

Getting to Know Your Appliance .................... 24

Control Panel ................................................. 25

ON / OFF ........................................................ 25

Child Lock ...................................................... 25

Remote Thermostat Mode

(Optional Accessory) ...................................... 26

Setting the Clock ............................................ 27

Setting and Operating the Timers .................. 27

Override Function .......................................... 27

Economy (Energy Saving Mode) ................... 28

Set Back ......................................................... 28

Humidifier and Air Flow Direction .................. 29

Required Care and Maintenance

Care and Maintenance .................................. 30

Before Making a Service Call ........................ 31

Diagnostic Codes and Remedies .................. 32

Restart Function............................................. 33

Troubleshooting ............................................. 33

Cut-Away Diagram ......................................... 34

Wiring Diagram .............................................. 35

Ladder Diagram ............................................. 36

Parts List ........................................................ 37

Warranty

Warranty ........................................................ 46

French Version............................................... 49

Rinnai Corporation EX08CT, EX11CT Manual 3

WARNING

CAUTION

Safety Behaviors and Practices for the Consumer and Installer

• Do not block the warm air discharge. Do not allow

anyone to sleep directly in front of the appliance.

• Due to high temperatures, the appliance should be

located out of traffic and away from furniture and

draperies.

• Children and adults should be alerted to the

hazards of high surface temperature and should

stay away to avoid burns or clothing ignition.

• Young children should be carefully supervised when

they are in the same room as the appliance.

• Clothing or other flammable material should not be

placed on or near the appliance.

• Any safety screen or guard removed for servicing

must be replaced prior to operating the appliance.

• Do not insert items into the louvers.

• Do not spray aerosols near the appliance while it is

operating. Most aerosols contain butane gas which

is flammable.

• Do not unplug the appliance while it is operating or

while the fans are on.

• Do not use bare hands to touch the front louvers

due to high temperatures which may cause burns.

• Wear hand protection when touching the side back

covers, front louver, and rear intake for the

convection fan.

• Prevent dust from accumulating on the power cord,

side covers, and parts behind the appliance.

• Do not sit on the heater.

• Do not place containers of liquid on top of the

heater. Water spillage can cause extensive

damage to the appliance and may result in electric

shock.

• Repairs should be performed by a qualified service

technician.

• Keep the area around the appliance clear and free

from combustible materials, gasoline, and other

flammable vapors and liquids.

• Never store liquid propane containers indoors.

• Do not use this appliance if any part has been under

water. Immediately call a qualified service

technician to inspect the appliance and to replace

any part of the control system and any gas control

which has been under water.

• This appliance is equipped with a three-prong plug

for your protection against shock hazard and should

be plugged directly into a properly grounded three-

prong receptacle. Do not cut or remove the ground

prong from this plug.

• Any alteration to the appliance or its controls can be

dangerous.

• Do not operate appliance with the panels removed,

cracked or broken. Replacement of the panels

should be done by a licensed or qualified service

person.

WARNING

California law requires this notice to be provided:

California Proposition 65:

This product can expose you to chemicals including Di (2-ethylhexyl) phthalate (DEHP) and carbon bisulfide

which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more

information, visit www.P65Warnings.ca.gov.

4 Rinnai Corporation EX08CT, EX11CT Manual

Installation Instructions (for the licensed professional)

State Regulations

NOTICE BEFORE INSTALLATION: Rinnai direct-vent appliance must be installed by a state qualified or licensed contractor and

a properly trained Rinnai Installer. If you are not properly trained, you must not install this unit.

IMPORTANT: In the State of Massachusetts (248 CMR 4.00 & 5.00)

For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in

part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent

termination is less than seven (7) feet above finished grade in the area of the venting, including but not limited to decks and

porches, the following requirements shall be satisfied:

1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas

fueled equipment, the installing plumber or gasfitter shall observe that a hard wired carbon monoxide detector with an alarm

and battery back-up is installed on the floor level where the gas equipment is to be installed. In addition, the installing

plumber or gasfitter shall observe that a battery operated or hard wired carbon monoxide detector with an alarm is installed

on each additional level of the dwelling, building or structure served by the side wall horizontal vented gas fueled equipment.

It shall be the responsibility of the property owner to secure the services of qualified licensed professionals for the

installation of hard wired carbon monoxide detectors

a. In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard

wired carbon monoxide detector with alarm and battery back-up may be installed on the next adjacent floor level.

b. In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner

shall have a period of thirty (30) days to comply with the above requirements; provided, however, that during said thirty

(30) day period, a battery operated carbon monoxide detector with an alarm shall be installed.

2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the

above provisions shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.

3. SIGNAGE. A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum

height of eight (8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled

heating appliance or equipment. The sign shall read, in print size no less than one-half (1/2) inch in size, "GAS VENT

DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS".

4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve

the installation unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in

accordance with the provisions of 248 CMR 5.08(2)(a)1 through 4.

When an existing Category I heater is removed or replaced, the original venting system may no longer be sized to properly vent

the attached appliances. Instructions shall also indicate effects of an improperly sized venting system (formation of condensate,

leakage, spillage, etc.) and shall specify the following test procedure.

WARNING: CARBON MONOXIDE POISONING HAZARD

Failure to follow the steps outlined below for each appliance connected to the venting system being placed into operation could

result in carbon monoxide poisoning or death.

The following steps shall be followed for each appliance connected to the venting system being placed into operation, while all

other appliances connected to the venting system are not in operation:

1. Seal any unused openings in the venting system.

2. Inspect the venting system for proper size and horizontal pitch, as required in the National Fuel Gas Code, ANSI Z223.1/

NFPA 54 or the Natural Gas and Propane Installation Code, CSA B149.1 and these instructions. Determine that there is no

blockage or restriction, leakage, corrosion and other deficiencies which could cause an unsafe condition.

3. As far as practical, close all building doors and windows and all doors between the space in which the appliance(s)

connected to the venting system are located and other spaces of the building.

4. Close fireplace dampers.

5. Turn on clothes dryers and any appliance not connected to the venting system. Turn on any exhaust fans, such as range

hoods and bathroom exhausts, so they are operating at maximum speed. Do not operate a summer exhaust fan.

6. Follow the lighting instructions. Place the appliance being inspected into operation. Adjust the thermostat so appliance is

operating continuously.

7. Test for spillage from draft hood equipped appliances at the draft hood relief opening after 5 minutes of main burner

operation. Use the flame of a match or candle.

8. If improper venting is observed during any of the above tests, the venting system must be corrected in accordance with the

National Fuel Gas Code, ANSI Z223.1/NFPA 54 and/or Natural Gas and Propane Installation Code, CSA B149.1.

9. After it has been determined that each appliance connected to the venting system properly vents when tested as outlined

above, return doors, windows, exhaust fans, fireplace dampers and any other gas-fired burning appliance to their previous

conditions of use.

WARNING

Rinnai Corporation EX08CT, EX11CT Manual 5

Included Installation and Venting Components

The following items are included with the appliance:

The following flue manifold sizes are

available for different wall thicknesses:

Name Kit No. fits walls

S Vent Kit FOT-150 3 - 4 1/2 in (75 - 115 mm)

A Vent Kit FOT-151 4 1/2 - 9 1/2 in (115 - 240 mm)

B Vent Kit FOT-152 9 1/2 - 15 3/4 in (240 - 400mm)

C Vent Kit FOT-153 15 3/4 - 23 5/8 in (400 - 600 mm)

D Vent Kit FOT-154 23 5/8 - 31 1/2 in (600 - 800 mm)

Flue Manifolds

Flue Manifold S laesrebburerap1 1

(‘A’ Flue units only)

(For weatherboard installations)

1

Manual Valve

Set

Owner’s Manual

“A” Vent Kit, FOT-151

Back Spacer

Set

Pipe Stopper A

Ring

Plastic tie

for air inlet

Clamp *

Screw

(M4.8 32)

Wood Screw

1

3

2

3

5

1

4

(M4)

Screw

(M4)

Screw

(M4)

Wall Bracket

Spacer Bracket 1

1

For Back Spacer Set

For Flue Manifold

For Air Intake Clip / Spacer Bracket

Wall Bracket Screws

“A” Vent Kit, FOT-151

* These clamps

should be located

here

(Vent Kit “A” is included

with the appliance.)

6 Rinnai Corporation EX08CT, EX11CT Manual

This appliance may be installed in an aftermarket,

permanently located, manufactured home (USA only)

or mobile home, where not prohibited by local codes.

This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is not

convertible for use with other gases, unless a certified

kit is used.

Installation Instructions

This appliance may be installed as an OEM

installation in a manufactured home (USA only) or

mobile home and must be installed in accordance with

the manufacturer’s instructions and the Manufactured

Home construction and Safety Standard, Title 24

CFR, Part 3280, in the United States, or the Mobile

Home Standard, CAN/CSA Z240 MH Series, in

Canada.

If installation is at a location above

2001 ft (610 m), then follow the Adjust

Gas Pressure Settings procedure.

Appliance input ratings are based on

sea level operation and need not be

changed for operation up to 2000 ft

(610 m) elevation.

NOTICE

A licensed professional must install the appliance,

inspect it, and leak test it before use. The warranty

will be voided due to any improper installation.

The installer should have skills such as:

• Gas sizing.

• Connecting gas lines, valves, and electricity.

• Knowledge of applicable national, state, and local

codes.

• Installing venting through a wall.

• Training in installation of direct vent furnaces.

(Training can be accessed on-line at

www.trainingevents.rinnai.us)

Installer Qualifications

General Instructions

Type of installaon

• For installation in residential and commercial

applications.

• Certified for installation in manufactured (mobile)

homes.

MUST DO

• If you move, check the gas type in your new area.

The local gas authority will be able to advise on

local regulations.

• The installation must conform with local codes or, in

the absence of local codes, with the National Fuel

Gas Code, ANSI Z223.1/NFPA 54, or the Natural

Gas and Propane Installation Code, CSA B149.1.

• A manufactured home (USA only) or mobile home

OEM installation must conform with the

Manufactured Home Construction and Safety

Standard, Title 24 CFR, Part 3280, or, when such a

standard is not applicable, the standard for

Manufactured Home Installations, ANSI Z225.1, or

the standard for Gas Equipped Recreational

Vehicles and Mobile Housing, CSA Z240.4.

• The appliance, when installed, must be electrically

grounded in accordance with local codes or, in the

absence of local codes, with the National Electrical

Code, ANSI/NFPA 70, or the Canadian Electrical

Code, CSA C22.1.

• The appliance and its appliance main gas valve

must be disconnected from the gas supply piping

system during any pressure testing of that system

at test pressures in excess of 1/2 psi (3.5 kPa).

• The appliance must be isolated from the gas supply

piping system by closing its equipment shutoff valve

during any pressure testing of the gas supply piping

system at test pressures equal to or less than 1/2

psi (3.5 kPa).

• If the flooring is carpet or other combustible materi-

al other than wood, then the appliance must be in-

stalled on a metal or wood panel extending the full

width and depth of the appliance.

• This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is not

convertible for use with other gases unless a certi-

fied kit is used. If conversion of the unit is needed,

conversions must be performed by a qualified ser-

vice provider at the owner’s expense.

• The appliance should be correctly sized for the

space it is required to heat. It is recommended that

an Industry standard BTU Heat Loss Calculation be

conducted to determine the proper sizing.

• Follow the installations instructions and those in

Care and Maintenance for adequate combustion

and ventilation air.

• This appliance discharges a large volume of warm

air next to the floor. Any particles in the air such as

cigarette smoke could cause discoloration in nylon

carpets containing dyes or vinyl surfaces.

• Rinnai suggests that a dedicated electrical circuit

with a 120VAC, 60 Hz, 10 amp power source be

used.

• A test plug is provided for testing of manifold

differential pressure. It is located on the modulating

gas valve.

Rinnai Corporation EX08CT, EX11CT Manual 7

WARNING

Do not use substitute materials.

Use only parts certified with the appliance.

DO NOT

• This appliance is not designed to built in.

• This appliance must not be connected to a chimney

flue serving a separate solid-fuel burning appliance.

• The flow of combustion and ventilation air shall not

be obstructed.

Prepare for Installation

Tools needed

Materials needed

• Pipe wrenches (2)

• Adjustable pliers

• Screwdrivers (2)

• Wire cutters

• Gloves

• Safety glasses

• Level

Tools that might be needed

• Hammer drill with

concrete bits

• Saw

• Threading machine with

heads and oiler

• Core drill with diamond

head

• Torch set

• Copper tubing cutter

• Steel pipe cutter

Materials that may be needed

• Soap or gas leak

detector solution

• Approved venting

• Teflon tape

(recommended) or pipe

compound

• Heat tape

• Pipe insulation

• Concrete wall anchors

• Optional pipe cover

• Optional temperature

controller

• 2 conductor 22 AWG

wire for controller

• Single gang electrical

box

• Wire nuts

Determine Installation Location

You must ensure that clearances will be met and that

the vent length will be within required limits. Consider

the installation environment. Requirements for the

gas line and electrical connection can be found in their

respective installation sections of this manual.

Environment

Air surrounding the venting, and vent termination(s) is

used for combustion and must be free of any

compounds that cause corrosion of internal

components. These include corrosive compounds

that are found in aerosol sprays, detergents, bleaches,

cleaning solvents, oil based paints/ varnishes, and

refrigerants.

The furnace, venting, and vent termination(s) should

not be installed in any areas where the air may

contain these corrosive compounds. If it is necessary

for a furnace to be located in areas that may contain

corrosive compounds, the following

instructions are strongly recommended.

IMPORTANT CONSIDERATIONS FOR:

• DO NOT Install in areas where air for combustion

might be contaminated with chemicals.

• Before installation, consider where air has the

ability to travel within the building to the furnace.

• Terminate the unit as far away as possible from

any air inlet vents. Corrosive fumes may be

released through these vents when air is not

being brought in through them.

• Chemicals that are corrosive in nature should not

be stored or used near the furnace or vent

termination.

Damage and repair due to corrosive compounds in the

air is not covered by warranty.

8 Rinnai Corporation EX08CT, EX11CT Manual

Flue Terminal Clearances

INSIDE

CORNER DE

TAIL

FIXED

CLOSED

OPERABLE

FIXED

CLOSED

OPERABLE

B

A

J

B

M

C

F

B

E

D

L

G

A

H

K

I

[1] A vent shall not terminate directly above a sidewalk or paved

driveway that is located between two single family dwellings and

serves both dwellings.

[2] Permitted only if veranda, porch, deck, or balcony is fully open on

a minimum of two sides beneath the floor.

 For clearances not specified in ANSI Z223.1/NFPA 54, clearances

are in accordance with local installation codes and the requirements

of the gas supplier.

Clearance to opposite wall is 24 inches (60 cm).

X

V

AIR SUPPLY INLET

VENT TERMINAL

AREA WHERE

TERMINAL IS NOT

PERMITTTED

Ref

Description

Canadian Installations US Installations

A Clearance above grade, veranda, porch, deck, or balcony 12 inches (30 cm) 12 inches (30 cm)

B Clearance to window or door that may be opened

EX08CT - 6 inches (15 cm)

EX11CT - 9 inches (23 cm)

EX08CT - 6 inches (15 cm)

EX11CT - 9 inches (23 cm)

C Clearance to permanently closed window * *

D

Vertical clearance to ventilated soffit, located above the terminal within a

horizontal distance of 2 feet (61 cm) from the center line of the terminal

* *

E Clearance to unventilated soffit * *

F Clearance to outside corner * *

G Clearance to inside corner * *

H

Clearance to each side of center line extended above meter/regulator

assembly

3 feet (91 cm) within a height 15

feet (4.5 m) above the meter/

regulator assembly

*

I Clearance to service regulator vent outlet 36 inches (91 cm) *

J

Clearance to non-mechanical air supply inlet to building or the combustion

air inlet to any other appliance

EX08CT - 6 inches (15 cm)

EX11CT - 9 inches (23 cm)

EX08CT - 6 inches (15 cm)

EX11CT - 9 inches (23 cm)

K Clearance to a mechanical air supply inlet 6 feet (1.83 m)

3 feet (91 cm) above if within 10

feet (3 m) horizontally

L

Clearance above paved sidewalk or paved driveway located on public

property

7 feet (2.13 m)  *

M Clearance under veranda, porch, deck, or balcony 12 inches (30 cm)  *

SNOW

TERMINATION

Clearance in

Ref. A also

applies to

anticipated

snow line

Clearance in

Ref. A also

applies to

anticipated

snow line

Rinnai Corporation EX08CT, EX11CT Manual 9

clearance for

maintenance

2 in

(50 mm)

2 in

(50 mm)

40 in

(1 m)

0” (0 mm)

When determining where to install the appliance the

clearances to combustibles shown in the figure must

be followed. Also refer to the Safety Behaviors and

Practices section.

Rinnai recommends 10” (254 mm) clearance from the

top and on both sides for servicing.

The 40 inch (1 meter) clearance from the

front of the appliance does not include

flooring material or carpeting that is less

than 1.2 inches (30 mm) in height.

NOTICE

Clearances to Combustibles

Checklist to Determine Installation

Location

□ The furnace is not exposed to corrosive

compounds in the air.

□ The furnace location complies with the clearances.

□ The planned venting will not exceed the maximum

length for the number of elbows used.

□ The planned venting termination/air intake location

meets the clearances.

□ Indoor air is not being used for combustion.

□ A standard 3 prong 120 VAC, 60 Hz properly

grounded wall outlet.

□ The installation must conform with local codes or,

in the absence of local codes, with the National

Fuel Gas Code, ANSI Z223.1/NFPA 54, or the

Natural Gas and Propane Installation Code, CSA

B149.1. If installed in a manufactured home, the

installation must conform with the Manufactured

Home Construction and Safety Standard, Title 24

CFR, Part 3280 and/or CAN/SCA Z240 MH

Series, Mobile Homes.

□ Leave the entire manual with the consumer.

Additional Clearances

Clearances to access the appliance during servicing

are 10 inches (254 mm) from the sides, 40 inches

(1 m) from the front, and the area shown above the

appliance in the picture.

10 Rinnai Corporation EX08CT, EX11CT Manual

Ensure that there are no gas or water lines, or

electrical circuits in the wall location where the flue hole

is to be drilled. Drill the flue hole using a 3 1/8 inch (80

mm) drill. The center of the hole must be located

exactly at the specified point.

See diagram. For weatherboard walls, drill through the

center of the weatherboard from the outside first and

then through the plasterboard. A template is provided.

For installation without using extension kits, the

configuration of the flue manifold, air intake hose, and

exhaust slide pipe should be as shown when

installation is completed. The 60 degree arc shows

where the flue manifold can be located.

1. Disassemble the flue manifold

The flue consists of 3 parts:

• sleeve

• inside connection

• outside terminal

Disassemble the flue manifold by first pulling out the

inside connection. To remove the outer terminal pull

and release the two internal ties and then pull out the

outer terminal.

Clearance to combustibles for the sleeve and flanges

is zero inches.

2. Adjust the sleeve length

Measure wall thickness through previously drilled 3

1/8 inch (80 mm) hole.

The end of the sleeve should protrude 3/16 - 3/8 inch

(5-10 mm) from the outside wall.

The sleeve is threaded for adjustment. Adjust the

sleeve length to wall thickness plus 3/16 - 3/8 inch

(5-10 mm).

NOTE: Do not extend beyond the red line.

For other than the “S” type flue manifold, if a shorter

length is necessary an extension can be removed.

Cut the outer plastic laminate (with a utility knife or

similar) and remove the extension. The metal should

not be cut.

• The flue manifold must exhaust to the outside. Do

not exhaust into other rooms.

• The flue manifold is not designed to be positioned

under floors or below the heater.

• The termination cannot be vertical.

• This appliance can only be used with one of the

five types of Rinnai flue kits. The flue kits and their

dimensions are listed in the Specifications section.

• Refer to the Flue Terminal Clearances section.

Inside Connection

Sleeve

Terminal

Remove extension

if necessary

Flue Hole

3 1/8"

(80 mm)

8 7/16"

(214 mm)

R11"

(R27

9

mm

)

R8.0"

(R206 mm

)

8 9/16"

(217 mm)

11"

(280 mm)

Cavity Opening

Use a template (included) to

determine allowable location of the

flue hole.

NOTICE

Drilling Flue Hole

Flue Manifold Installation

Rinnai Corporation EX08CT, EX11CT Manual 11

5. Lock the ties

Pulling hard on the left and right hand ties,

clip the ties over the notches inside the

sleeve. You should be able to pull the ties 2

or 3 notches past the starting point. Cut the

ties, leaving about 3/4 inch (20 mm) past the

notch. Bend the ties back into the sleeve and

parallel to the wall.

6. Insert Inside Connection Assembly

Push the assembly into the terminal tube,

ensuring that the seal is in place on the

inner tube.

Attach the inside connection with 3

screws. The inner connection can still

be turned to install the screws.

4. Install the Terminal

Check that the terminal seal is in place. For

weatherboard walls, add the second seal next

to the terminal seal to compensate for

weather board angle.

From the outside insert the terminal into the

sleeve with the marking “TOP” at the top.

The left hand side locking tie should be

marked “LEFT”.

Terminal seal

Locking tie

Terminal

Locking ties

Sleeve

3 screws

sleeve should

extend 3/16 -

3/8 in (5-10

mm)

3. Attach the sleeve

Attach to the inside wall using 3

screws arranging the flange so that the

marking “TOP” is at the top.

The flange is offset 2° to allow the

condensate drain to the outside.

3 screws

Flue Manifold Installation

12 Rinnai Corporation EX08CT, EX11CT Manual

INCORRECT

• Too many bends (limit is 2)

• Air intake hose is above

exhaust pipe

Extension through the top

AIR

INTAKE

HOSE

EXHAUST

PIPE

CLAMP

PIPE

STOPPER A

CLAMP

Extension to the right (facing appliance)

CLAMP

PIPE

STOPPER A

PIPE

CLAMP

LONG

BENT

ELBOW

EXHAUST

ELBOW

AIR

INTAKE

HOSE

EXHAUST

PIPE

Extension to the left (facing appliance)

CLAMP

PIPE

STOPPER A

PIPE

CLAMP

LONG BENT ELBOW

EXHAUST

ELBOW

AIR

INTAKE

HOSE

EXHAUST

PIPE

If necessary, extension kits are available to extend the

exhaust line and air intake hose between the manifold

and the appliance.

(1) The maximum vent length is 13 feet (4 m) with 2

bends. The bent pipe attached to the appliance

does not count toward the max limit of 2 bends.

(2) For altitudes at or below 2000 feet (610 m), the

maximum vertical length is 8 feet (2.4 m). For

altitudes above 2000 feet (610 m), the maximum

vertical length is 5 feet (1.5 m).

(3) If the extension is longer than that shown in the

table below, the condensate may overflow the

condensation pan. Therefore, extensions

exceeding this length should drain to the outside

and sloped 3° downward.

(4) Do not allow any low points or sagging in the

exhaust line. Otherwise, condensate may block

the exhaust and affect combustion.

(5) Vent extensions installed in unconditioned air

space must be insulated with high temperature

insulation and must be accessible.

(6) Vent extensions must not be concealed per NFPA

54 and must be accessible allowing inspection and

repair. Decorative covers are available from

Rinnai.

These figures show the 3 possible ways that the

extension exhaust line and air intake hose may be

directed away from the appliance. All 3 views are from

behind the appliance. For your configuration,

position the air intake hose as shown.

8 feet (2.4 m) at or below 2000 feet (610 m)

5 feet (1.5 m) above 2000 feet (610 m)

Extension Kit Installation (EX11CT only)

Rinnai Corporation EX08CT, EX11CT Manual 13

Clearances

exhaust pipe to combustibles 1 inch (25.4 mm)

exhaust pipe to non-combustibles zero

Both the exhaust line and air intake hose are

supported by clamps which are attached to the wall.

A wall fixture can be used to offset the clamp from the

wall. Use Screw B to attach the wall fixture to the

wall. If the wall fixture is not used then use Screw A

and the nut to attach the clamp to the wall.

The air intake hose should always be underneath the

exhaust line so that in case the air line sags it will not

come into contact with the exhaust line.

Clamps

Exhaust pipe

Air intake hose

The exhaust line is connected between the bent pipe

at the rear of the heater and the exhaust port on the

flue manifold.

Installing the Exhaust Line

To connect exhaust pipes with other straight pipes or

bends, fit the male end into the female end. Use pipe

stopper A to clamp the connection.

Use pipe stopper B to fix the length on the adjustable

exhaust pipes. Do not extend these pipes beyond the

red line.

Do not cut the exhaust pipe. Use the adjustable

pipes if necessary.

To bend the elbow, insert exhaust pipes into both

ends for additional leverage. Bend to desired angle.

Do not straighten the bent pipe attached to the

appliance.

Pipe stopper A

Pipe stopper B

Male end

Female end

Adjust the angle

Connecting the Air Intake Hose

The air intake hose is connected between the air

connection at the rear of the heater and the air intake

port on the flue manifold.

Push the air intake hose onto the flue manifold and

secure with the plastic cable tie.

Join air intake hoses by screwing the hose joint half of

its length into the air intake hose and then screwing

another air intake hose into the hose joint.

The lengths of the air intake hose and the exhaust

pipe must be the same in order for the appliance to

operate properly. The hose can be cut to the required

length. Deburr all rough edges. Do not cut the hose

attached to the appliance.

Support the air intake hose with pipe clamps.

Hose joint

Air intake hoses

CAUTION

Use the pipe stoppers, connectors, clamps, and screws according to these instructions in

order to ensure no leakage of exhaust gases.

Do not cut the intake hose. Cutting

the intake hose may result in noise.

NOTICE

Extension Kit Installation (EX11CT only)

14 Rinnai Corporation EX08CT, EX11CT Manual

Item Description FOT-201 FOT-155 FOT-156 FOT-157 FOT-158 FOT-190

1 Exhaust Pipe (adjustable)

11.4-20.3 in (290-515 mm)

1

1 Exhaust Pipe (adjustable)

21.0-39.6 in (533-1005 mm)

1 1

2 Exhaust Pipe - 40 in (1016 mm) 1

3 Air Intake Hose - 29.5 in (750 mm);

1.5 in (38 mm) inner dia.

1 1

3 Air Intake Hose - 29.5 in (750 mm);

2.0 in (50 mm) inner dia.

1

3 Air Intake Hose - 49.2 in (1.25 m) 1

3 Air Intake Hose - 90.6 in (2.3 m) 1

4 Bent Elbow 1

5 Long Bent Elbow 1 1

6 Hose Joint - 1.5 in (38 mm) inner dia. 1 1 1 1

6 Hose Joint - 2.0 in (50 mm) inner dia. 1

7 Pipe Stopper A 1 1 1 2 1 1

8 Pipe Stopper B 1 1 1

9 Pipe Clamp 2 sets 3 sets 4 sets

10 Wall Fixture 2 3 4

11 Nut 2 3 4

12 Screw A 2 3 4

13 Screw B 4 6 8

Extension Kits and Parts

EXHAUST PIPE (ADJUSTABLE)

EXHAUST PIPE (NON ADJUSTABLE)

AIR INTAKE HOSE

BENT ELBOW

LONG BENT ELBOW

HOSE JOINT

PIPE STOPPER B

PIPE CLAMP WALL-FIXTURE

NUT

SCREW A

PIPE STOPPER A

SCREW B

TOP STOPPER

Extension Kit Installation (EX11CT only)

Rinnai Corporation EX08CT, EX11CT Manual 15

Pipe stopper

Elbow

Manifold

Hook

Pipe stopper

Connecting the Appliance

1. Attach the air inlet hose to the flue manifold on

either inlet position “a” or “b”.

The plastic tie should be tight over the sleeve.

The unused inlet is plugged with the rubber cap

supplied on the manifold.

2. Connect the flue elbow to the manifold while

moving the appliance into position.

3. Fit the pipe stopper over the connection between

the flue elbow and the manifold. Engage the

hook and rotate it until it snaps against the body

of the clamp.

4. Slide the insulation sleeve up to the flue manifold

and slip the securing clip over the sleeve as

shown.

5. Install the bracket on the rear of the top spacer by

tightening 2 screws.

6. Install the wall bracket with two screws. Install

the top spacer by clipping the spacer into the wall

brackets and attaching it to the heater with 2

screws.

Flue Manifold

a

b

Wall

Bracket

Top Spacer

2 screws

Spacer

Bracket

Wall

Bracket

Top Spacer

Spacer

Bracket

16 Rinnai Corporation EX08CT, EX11CT Manual

□ Verify proper clearances around the vents and air

intakes.

□ Ensure you have used the correct venting

products for the model installed and that you have

completely followed the venting manufacturer’s

installation instructions and these installation

instructions.

□ Verify that the vent system does not exceed the

maximum length for the number of elbows used.

Checklist for Venting

Gas Connection

When connecting the gas valve or other gas

components in the gas line, use a backup wrench to

ensure the connection is gas tight.

WARNING

• The gas supply line shall be gas tight, sized and so

installed as to provide a supply of a gas sufficient to

meet the maximum demand of the furnace without

loss of pressure.

• A shut off valve and appliance connector valve

should be installed in the upstream of the gas line

to permit servicing.

• Flexible pipe and any appliance connector valve

used for gas piping shall be types approved by

nationally recognized agencies.

• Any compound used on the threaded joint of the

gas piping shall be a type which resists the action

of liquefied petroleum gas (propane).

• After completion of gas pipe connections all joints

including the furnace must be checked for gas

tightness by means of leak detector solution, soap

and water, or an equivalent nonflammable solution,

as applicable. (Since some leak test solutions,

including soap and water, may cause corrosion or

stress cracking, the piping shall be rinsed with

water after testing, unless it has been determined

that the leak test solution is non-corrosive.)

• Check the gas supply pressure immediately

upstream at a location provided by the gas

company. Supplied gas pressure must be within

the limits shown in the Specifications section.

• Refer to an approved pipe sizing chart if in doubt

about the size of the gas line.

Adjust Gas Pressure Settings

Complete these instructions for altitude and vent

length. (Default altitude: 0ft - 2,000ft. Default vent length:

0 - 7ft+1 elbow )

For high altitude installations in Canada, the conversion

shall be carried out by a manufacturer’s authorized

representative, in accordance with the requirements of

the manufacturer, provincial or territorial authorities

having jurisdiction and in accordance with the

requirements of CAN/CGA-B149.1 or CAN/CGA-B149

installation codes.

CAUTION

Do not touch any other areas on the PC board

besides the “SW” switches while power is supplied to

the appliance. Parts of the PC board are supplied

with 120 volts AC.

CAUTION

Do not insert hands or objects into the circulation fans

while they are running. Injury or mechanical

malfunction may occur.

CAUTION

Do not touch the areas at or near the exhaust. This

area becomes very hot and could cause burns.

The regulator has been factory pre-set. If the

pressure is incorrect, check the supply pressure first,

before making any adjustments to the appliance.

Also, if the low control pressure cannot be obtained,

adjust the adjustment screw on the proportional valve

to roughly set pressure and then recheck both the low

and high fire pressures.

NOTICE

Rinnai Corporation EX08CT, EX11CT Manual 17

1. Turn off the gas and the power supply.

2. Remove the 5 screws that hold the louver assembly

and front panel. Lift the panel straight up and then

remove it.

3. Remove two pressure point screws (1/8 NPT tap) with

3/16 Allen wrench and attach the manometer to both

pressure points. Both pressure points must be used

in order to measure the differential pressure. Ensure

that the manometer is properly calibrated.

4. Turn on the gas and power supply to the appliance.

(Press the “Set back” button after turning on the

power supply.) With the unit in the off position, press

the test switch at the top of PC board until it beeps.

5. Select the correct code for gas type and altitude using

▲ and ▼ buttons. Refer to the table below.

6. Press the test switch twice to record the gas type

code into memory. .

7. Press the ON/OFF button to operate the appliance.

8. Press the test switch twice. The LED will display

“PL”.

9. Compare the pressure reading on the manometer to

the desired manifold test pressure (low) for your gas

type and altitude. If necessary adjust the low fire

pressure using the ▲ and ▼ buttons.

10. Press the test switch. The LED will display “PH”

indicating high fire mode.

Natural Gas Propane Gas

Code A1 / A5 * A2 / A6 * A3 / A7 * A4 /A8 * L1 / L5 L2 / L6 L3 / L7 L4 / L8

Altitude

0-2000 ft

0-610 m

2001-5200 ft

611-1585 m

5201-7700 ft

1586-2347 m

7701-10200 ft

2348-3109 m

0-2000 ft

0-610 m

2001-5200 ft

611-1585 m

5201-7700 ft

1586-2347 m

7701-10200 ft

2348-3109 m

EX08CT

Manifold test

pressure -

W.C. Low

0.58 in

(15 mm)

0.62 in

(16 mm)

0.70 in

(18 mm)

0.78 in

(20 mm)

0.86 in

(22 mm)

0.92 in

(24 mm)

1.04 in

(27 mm)

1.16 in

(29 mm)

Manifold test

pressure -

W.C. High

3.4 in

(86 mm)

3.6 in

(92 mm)

4.1 in

(103 mm)

3.2 in

(82 mm)

5.8 in

(147 mm)

6.2 in

(158 mm)

7.0 in

(177 mm)

5.5 in

(140 mm)

EX11CT

Manifold test

pressure -

W.C. Low

0.60 in

(15 mm)

0.64 in

(16 mm)

0.72 in

(19 mm)

0.80 in

(20 mm)

1.06 in

(27 mm)

1.16 in

(29 mm)

1.28 in

(33 mm)

1.41 in

(36 mm)

Manifold test

pressure -

W.C. High

2.2 in

(56 mm)

1.9 in

(49 mm)

1.7 in

(44 mm)

1.6 in

(40 mm)

3.8 in

(95 mm)

3.3 in

(84 mm)

3.0 in

(75 mm)

2.7 in

(69 mm)

Pressure

Point

Pressure

Point

Nozzle Manifold

Test Switch

PC Board

* For the EX11CT with natural gas: Use A1, A2, A3, or A4 for venting up to 7 feet (2.1 m) with one elbow.

Use A5, A6, A7, or A8 for venting exceeding 7 feet (2.1 m) with one elbow.

Adjust Gas Pressure Settings

18 Rinnai Corporation EX08CT, EX11CT Manual

11. Compare the pressure reading on the manometer

to the desired manifold test pressure (high) for

your gas type and altitude. If necessary adjust

the high fire pressure using the ▲ and ▼ buttons.

12. Press the ON/OFF button again. The LED display

turns blank and the appliance returns to the

normal OFF mode.

13. Remove manometer and install Allen head

screws. Operate the unit and

1. Install the front panel and bottom cover.

2. If doing a gas type conversion, place the new

conversion plate (label) on the front cover.

Check that the burner flames are operating normally.

The flame can be seen through the circular window

through the louvers.

When operating normally the burner flame should

appear as long, clear, blue, stable, streaks. Yellow

flames or an orange color is abnormal and

maintenance is required.

Visual Inspection of Flame

NORMAL

Flame Rod

Long, clear, blue,

stable flames

ABNORMAL

Yellow flames or

orange color

Flame Rod

Final Assembly

•check the normal operating sequence

•visually inspect the flame

•check for gas leaks at the test points

Normal Operating Sequence

When you press the ON/OFF button, the LED display

will illuminate, the combustion fan will begin to run,

and the spark will ignite the main burner.

This heater has an automatic ignition system. When

the main burner has lit, the combustion lamp will glow

red, and the spark will stop.

Adjust Gas Pressure Settings

Checklist for Gas and Electricity

□ A manual gas control valve is placed in the gas

line to the heater.

□ Check the gas lines and connections for leaks.

□ Confirm that the gas inlet pressure is within limits.

□ Confirm that the heater is rated for the gas type

supplied.

□ Confirm that the electricity is supplied from 120

VAC, 60 Hz power source and is in a properly

grounded circuit.

□ Confirm that an extension cord or an adapter plug

has NOT been used with the heater.

Rinnai Corporation EX08CT, EX11CT Manual 19

Final Checklist

□ The heater is not subject to corrosive compounds

in the air.

□ Clearances from the heater unit are met.

□ Clearances from the vent termination are met.

□ Ensure you have used the correct venting

products for the model installed and that you have

completely followed the venting manufacturer’s

installation instructions and these installation

instructions.

□ Verify that the vent system does not exceed the

maximum length for the number of elbows used.

□ A manual gas control valve has been placed in the

gas line to the heater.

□ Check the gas lines and connections for leaks.

□ Confirm that the gas inlet pressure is within limits.

□ Confirm that the heater is rated for the gas type

supplied.

□ Confirm that the electricity is supplied from a 120

VAC, 60 Hz power source, is in a properly

grounded circuit, and turned on.

□ Verify the system is functioning correctly by

connecting your manometer to the gas pressure

test port on the water heater. Operate all gas

appliances in the home or facility at high fire. The

inlet gas pressure at the heater must not drop

below that listed on the rating plate.

□ Install the front panel.

□ Explain to the customer the importance of not

blocking the vent termination.

□ Explain to the customer the operation of the

heater, safety guidelines, maintenance, and

warranty.

□ The installation must conform with local codes or,

in the absence of local codes, with the National

Fuel Gas Code, ANSI Z223.1/NFPA 54, or the

Natural Gas and Propane Installation Code, CSA

B149.1. If installed in a manufactured home, the

installation must conform with the Manufactured

Home Construction and Safety Standard, Title 24

CFR, Part 3280 and/or CAN/SCA Z240 MH

Series, Mobile Homes.

□ Leave the entire manual with the consumer.

20 Rinnai Corporation EX08CT, EX11CT Manual

A full size template is provided on the

cardboard packaging.

DO NOT DISCARD until installation is

completed.

NOTICE

10.1 in

257 mm

3.3 in

85

6.8 in

172 mm

inches (mm)

Dimensions

La page charge ...

Rinnai RHFE-265FTA-2A-N Mode d'emploi

Rinnai RHFE-265FTA-2A-N Mode d'emploi

dans d''autres langues

Documents connexes