GE Monogram ZGU384N Manuel utilisateur

Marque: GE Monogram

Modèle: ZGU384N

Catégorie: Cuisinières

Taper: Manuel utilisateur

Ce manuel convient également à

Cooktop ZGU384N

Installation

Instructions

d’installation

30″ Stainless Steel

Gas Cooktops

Natural Gas Model:

ZGU384N

LP Gas Model:

ZGU384L

Questions?

Call 800.GE.CARES

or Visit our Website at:

www.monogram.com

Appelez le Centre de réponse 1.800.561.3344

ou visitez notre site Web à l’adresse :

www.electromenagersge.ca

31-10635-2

08-07 JR

Surfaces de cuisson

au gaz de acier

inoxydable de 30 po

(76 cm)

Modèle à gaz naturel :

ZGU384N

Modèle à gaz PL :

ZGU384L

La section française commence

à la page 19.

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT — Save these instructions

for local inspector’s use.

•

IMPORTANT — Observe all governing

codes and ordinances.

• Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these instructions for

future reference.

• Product failure due to improper installation is not

covered under the Warranty.

WARNING — This appliance must be

properly grounded.

•

IMPORTANT — Leak testing of the

appliance shall be conducted according to the

manufacturer’s instructions.

• Proper installation is the responsibility of the

installer and product failure due to improper

installation is NOT covered under warranty.

FOR YOUR SAFETY:

WARNING — If the information

in this manual is not followed exactly, a fire,

explosion or gas leak may result, causing

property damage, personal injury or death.

Do not store or use gasoline or other

flammable vapors and liquids in the

vicinity of this or any other appliance!

WHAT TO DO IF YOU

SMELL GAS:

• Do not try to light any appliance. Do not touch

any electrical switch; do not use any phone in

your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call the fire

department.

Installation and service must be performed by

a qualified installer, service agency or the gas

supplier.

WARNING — Disconnect all electrical

power at the main circuit breaker or fuse box

before installing.

This cooktop has been design certified by Underwriters

Laboratories. You’ll find safety precautions in your

Owner’s Manual. Read them carefully.

• Installation of this cooktop must conform with

local codes or, in the absence of local codes, with

the National Fuel Gas Code, ANSI Z223.1/NFPA

54–Latest Edition.

• Be sure your cooktop is installed properly by a

qualified installer or service technician.

• To eliminate reaching over surface burners,

cabinet storage above burner should be avoided.

• Do not install the unit near an outside door or

where a draft may affect its use.

IN THE COMMONWEALTH OF MASSACHUSETTS:

• This product must be installed by a licensed

plumber or gas fitter.

• When using ball-type gas shut-off valves,

they shall be the T-handle type.

• A flexible gas connector, when used, must not

exceed 3 feet.

Be sure the installation of this product in a mobile

home conforms with the Manufactured Home

Construction and Safety Standard, Title 24 CFR,

Part 3280. If this standard does not apply, you

must follow the standard for Manufactured Home

Installations, ANSI A225.1 and Manufactured Home

Installations, Sites and Communities, ANSI/NFPA

501A or with local codes. You can get a copy of

the Federal Standard by Writing:

Office of Mobile Home Standards

HUD Building

451 7th Street, S.W.

Washington, D.C. 24010

Safety Information

CONTENTS
Installation Preparation
Models Available  . . . . . . . . . . . . . . . . . . . . . . . . .4
Parts Included . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Materials You May Need  . . . . . . . . . . . . . . . . . 4
Tools You Will Need . . . . . . . . . . . . . . . . . . . . . . 4
Advance Planning and 
Installation Options  . . . . . . . . . . . . . . . . . . . . . . 5
Pre-Installation Checklist . . . . . . . . . . . . . . . . . 6
Dimensions and Clearances . . . . . . . . . . . . . . 7
Gas Supply Locations . . . . . . . . . . . . . . . . . . . . 8
Installation Instructions
Step-by-Step Instructions  . . . . . . . . . . . . 9–11
Operation Checklist . . . . . . . . . . . . . . . . . . . . . 11
Installation Options
Installation With a Downdraft Vent . . . . . . 12
Installation Over a Warming Drawer  . . . . 13
Installation Over a Single Oven . . . . . . . . . . 14
Installation Instructions for Natural 
to LP Gas Conversion
Tools You Will Need  . . . . . . . . . . . . . . . . . . . . 15
Adjusting the Regulator . . . . . . . . . . . . . . . . . 15
Changing the Orifices  . . . . . . . . . . . . . . . 15, 16
Adjusting Burner Flames . . . . . . . . . . . . . . . . 16
Installation Instructions for LP 
to Natural Gas Conversion
Tools You Will Need  . . . . . . . . . . . . . . . . . . . . 17
Adjusting the Regulator . . . . . . . . . . . . . . . . . 17
Changing the Orifices  . . . . . . . . . . . . . . . 17, 18
Adjusting Burner Flames . . . . . . . . . . . . . . . . 18
ELECTRICAL REQUIREMENTS
This appliance must be supplied with the proper
voltage and frequency and connected to an
individual, properly grounded branch circuit, protected
by a circuit breaker or fuse having amperage as noted
on the rating plate.
We recommend you have the electrical wiring and
hookup of your cooktop connected by a qualified
electrician. After installation, have the electrician show
you where your main cooktop disconnect is located.
Check with your local utilities for electrical codes
which apply in your area. Failure to wire your 
cooktop according to governing codes could 
result in a hazardous condition. If there are no codes,
your cooktop must be wired and fused to meet the
requirements of the National Electrical Code,
ANSI/NFPA No. 70—Latest Edition. You can 
get a copy by writing:
National Fire Protection Association
Batterymarch Park
Quincy, MA  02269
In Canada, your cooktop must be wired and 
fused to meet the requirements of the Canadian
Electrical Code.
Safety Information
3

PARTS INCLUDED TOOLS YOU WILL NEED

FOR INSTALLATION

MODELS AVAILABLE

ZGU384N

30″ natural gas cooktop

ZGU384L

30″ LP gas cooktop

These models are factory set for either natural

gas or LP gas operation. Be sure to order the

correct model for the installation situation.

Saber Saw

Pencil

Safety Glasses

1/8″ Drill Bit &

Electric or Hand

Drill

Ruler or

Straightedge

Phillips Head

Screwdriver

Pipe Wrench

MATERIALS YOU MAY NEED

2 Hold

Down Brackets

Shut Off

Valve

Pipe Fittings

CSA-Approved Flexible Gas Line

1/2

″ Min. ID, 1/2″ NPT Connection,

3-foot Maximum Length (Massachusetts Only)

NOTE: Purchase new line, do not use

previously used flexible gas line.

Joint

Sealant

Regulator

2 Screws

Installation Preparation

ADVANCE PLANNING

• Refer to “Installation Preparation” for

information on appropriate placement and

necessary clearances when planning

installation.

• Avoid placing cabinetry directly above cooktop

when possible.

• If cabinetry is used above cooking surface:

– Use cabinets no more than 13″ deep.

– Maintain 30″ minimum clearance between

cooktop and unprotected cabinets directly

above cooktop.

– If clearance is less than 30″, protect cabinet

bottoms with flame-retardant millboard at

least 1/4″ thick, or gypsum board at least

3/16″ thick, covered with 28 gauge sheet

steel or .02″ thick copper.

– Clearance between cooktop and protected

cabinetry must not be less than 24″.

– An exhaust hood that projects at least 5″

beyond front of cabinets can reduce risk

of burns caused by reaching over heated

surface units.

– Working areas adjacent to the cooktop

should have 18″ minimum clearance between

countertop and cabinet bottom.

•A 30″ or wider exhaust hood with 350 CFM or

greater airflow rating is recommended for use

over this Monogram cooktop.

• Installation must conform with local codes.

In the absence of local codes, the gas cooktop

must comply with the National Fuel Gas Code,

ANSI Z223.1, latest edition.

• Gas supply should be located near the opening

for this cooktop (see Preparing the Opening and

Gas Connection sections of this manual). The

supply should provide natural gas at 7″ of water

column pressure (11″ of water column for LP

gas) and a maximum of 14″ of water column

for natural or LP gas.

• The electric spark ignition feature for this

model requires a 120V electrical power supply

be located in the immediate vicinity of this

cooktop (see Electrical Connections section

of this manual).

WB28T10185 High Altitude Kit

For operation above 5,000 feet, order

WB28T10185 Conversion Kit. This kit includes

orifices for both LP and Natural gas operation.

Installation Preparation

INSTALLATION OPTIONS

Cooktop and ZVB30 Downdraft Vent Combination

Installation

These cooktops may be installed with a 30″

Monogram Downdraft Vent, model ZVB30.

See page 12 for cutout and clearances.

– The countertop must have a deep flat surface to

accommodate the combined installation of the

cooktop and vent.

– The downdraft vent with blower, motor and

ductwork will occupy the base cabinet.

– Consideration must be given to electrical and gas

supply locations. See page 8.

Cooktop and ZTD910 or ZKD910 Warming Drawer

Combination Installation

These cooktops may be installed over a Monogram

30″ or 27″ Warming Drawer, model ZTD910 or

ZKD910. See page 13 for cutout and clearances.

– Consideration must be given to electrical and gas

supply locations. See page 8.

Cooktop and ZET1, ZEK938 or ZET938 Single Oven

Combination Installation

These cooktops may be installed over a Monogram

27″ or 30″ Oven, model ZET1, ZEK938 or ZET938.

See page 14 for cutout and clearances.

– Consideration must be given to electrical and gas

supply locations. See page 8.

Installation Above Cabinet Drawers

• When installing the cooktop above a base

cabinet with drawers, it may be necessary to

use a shorter depth (front to back) drawer to

allow clearance for the gas connection.

PRE-INSTALLATION CHECKLIST

1. When preparing cooktop opening, make sure

the inside of the cabinet and the cooktop do

not interfere with each other. (See section on

preparing the opening.)

2. Slide the cooktop out of the end of the box.

Remove packaging materials, grate boxes,

regulator and literature package from the

cooktop before beginning installation.

• Use the shipping carton as a pad to protect

customer countertops or flooring.

3. Remove Installation Instructions from literature

package and read them carefully before you

begin.

Be sure to place all literature, Owner’s Manual,

Installations, etc. in a safe place for future

reference.

4. Make sure you have all the tools and materials

you need before starting the installation of the

cooktop.

5. Your home must provide the adequate electrical

service needed to safely and properly use your

cooktop. (Refer to section on electrical

requirements.)

6. When installing your cooktop in your home, make

sure all local codes and ordinances are followed

exactly as stated.

7. Make sure the wall coverings, countertop and

cabinets around the cooktop can withstand heat

(up to 200°F) generated by the cooktop.

Foam support

Packaging containing

left and right side grates

Packaging containing

left and right side grates

Installation Preparation

Foam packaging

Regulator taped

to the underside

DIMENSIONS AND CLEARANCES

1. Overall cooktop dimensions:

2. Use a 30″ or wider base cabinet.

• Cut the opening in the countertop. To ensure

accuracy, it is best to make a template for the

opening. Make sure the sides of the opening are

parallel and the rear and front cuts are exactly

perpendicular to the sides.

• Observe all minimum clearances.

3. Make sure the wall coverings, countertop and

cabinets around the cooktop can withstand heat

(up to 200°F) generated by the cooktop.

3-3/4″

30-3/4″

21-5/8″

deep at

center

Installation Preparation

12″ min.

from cutout

to side wall

2-1/2″ min.

from cutout

to front of

countertop

2-7/8″ min.

from cutout

to rear vertical

combustibles

12″ min.

from cutout

to side wall

28-1/2″

30″ or wider

cabinet base

recommended

19-5/8″

30″ min.

13″ max.

30″

min.

18″ min.

21″

POWER SUPPLY LOCATIONS

Gas supply:

These cooktops are shipped from the factory set

for either natural gas or LP gas. Check to be sure

you have the correct cooktop for the type of gas

being used.

• The pressure regulator must be connected in series

with the manifold of the cooktop and must remain

in series with the supply line regardless of type of

gas being used.

• The natural gas model is designed to operate at

5″ water column pressure. A regulator is required

at the natural gas source to provide a minimum

of 6″ water column to the cooktop regulator.

• The liquid propane model is designed to operate at

10″ water column pressure. A regulator is required

at the LP source to provide a minimum of 11″ water

column to the cooktop regulator.

• Maximum inlet pressure for the regulator supplied

with the cooktop is 14″ water column regardless of

the gas being used.

For ease of installation, and if local codes permit,

the gas supply line into the cooktop should be 1/2″

or 3/4″ ID flexible metal appliance connector, three

to five feet long.

NOTE: Purchase new flexible line. DO NOT USE OLD,

PREVIOUSLY USED FLEXIBLE LINE.

• Make gas connection through rear wall, or on

cabinet floor at rear, as illustrated.

1. Install the house gas supply at least 1″ from

the back wall.

2. Locate the electrical outlet 12″ below the

countertop.

Rear–Burner Box

The gas inlet is

located on the

bottom of the

burner box, at

the right rear.

Install a manual shut-off valve in the gas line in an

easily accessible location outside the cooktop. Be

sure you know how and where to shut off the gas

supply to the cooktop. Install the electrical outlet

12″ below the countertop.

Electrical supply:

This cooktop features pilotless electric ignition for

energy savings and reliability. It operates on a 120 volt,

60 Hz power supply. A separate circuit, protected by a

15 amp time delay fuse or circuit breaker, is required.

• A properly-grounded 3-prong receptacle should

be located within reach of the cooktop’s four-foot

power cord.

IMPORTANT: (Please read carefully). FOR PERSONAL

SAFETY, THIS APPLIANCE MUST BE PROPERLY

GROUNDED.

• The power cord of this appliance is equipped with

a three-prong (grounding) plug which mates with a

standard three-prong grounding wall receptacle to

minimize the possibility of electric shock hazard

from this appliance.

• The customer should have the wall receptacle and

circuit checked by a qualified electrician to make sure

the receptacle is properly grounded and has correct

polarity.

• Where a standard two-prong wall receptacle is

encountered, it is the personal responsibility and

obligation of the customer to have it replaced with

a properly grounded three-prong wall receptacle.

Do Not, Under Any Circumstances, Cut Or Remove

The Third (Ground) Prong From The Power Cord.

Do not use an extension cord.

Installation Preparation

Optional Combination Installations

This cooktop may be installed in combination

with a ZVB30 Monogram Downdraft Vent, a ZET1,

ZEK938 or ZET938 Single Oven or a ZTD910 or

ZKD910 Warming Drawer.

• The gas and electrical supply must be located

where it will not interfere with vent housing, the

oven or the warming drawer. Review pages 12

to 14 for additional installation requirements.

1”

min.

12”

Gas

supply

line

1-5/8”

2”

Gas Inlet

Installation Instructions

INSTALL THE COOKTOP

A. Remove the screws on the sides of the cooktop

burner box. Use those screws to attach the side

mounting brackets.

B. Insert the cooktop centered into the cutout

opening. Make sure the front edge of the

countertop is parallel to the cooktop.

Check clearances at the front, back and sides.

Secure the hold-down bracket to the cabinet

sides with screws.

Cooktop

INSTALL PRESSURE REGULATOR

WARNING: Never reuse old flexible

connectors. The use of old flexible connectors can

cause gas leaks and personal injury. Always use

new flexible connectors when installing a gas

appliance.

To reduce the possibility of gas leaks, apply teflon

tape or a thread compound approved for use with

LP or Natural gases to all threaded connections.

A. Screw the regulator onto the burner box

bottom pipe connection. Make sure the top of

the regulator is facing toward the cabinet front,

and the arrow on the back of the regulator

points to the cooktop.

Pressure

regulator

Shut-off

valve

Electrical outlet 12″

below countertop

To cooktop

Rear view

of regulator

(note

direction

of arrow)

INSTALL PRESSURE REGULATOR

(cont.)

OPTION: You can install a 90º elbow (not supplied)

onto the gas inlet and route the gas connections to

avoid interference when installed over an oven,

with a downdraft vent, a warming drawer or other

cabinetry features.

B. Complete the connection between the regulator

and the shut-off valve.

C. Before testing for leaks, make sure all burner

knobs are in the OFF position.

After connecting the cooktop to gas, check

system for leaks with a manometer. If a manometer

is not available, turn the gas supply on to the

cooktop and use a liquid leak detector at all

joints and connections to check for leaks.

Tighten all connections if necessary to prevent gas

leakage in the cooktop or supply line.

WARNING: Do not use a flame to

check for leaks.

Disconnect the cooktop and its individual shut-off

valve from the gas supply piping system during any

pressure testing of that system at test pressures

greater than 1/2 psig (3.5 kPa).

Isolate the cooktop from the gas supply piping

system by closing its individual shut-off valve during

any pressure testing of the gas supply system at

test pressures equal to or less than 1/2 psig (3.5 kPa

CONNECT ELECTRICAL

• Check to be sure the receptacle is properly

grounded.

• Plug in the power cord.

Burner Box

Elbow

ASSEMBLE BURNERS,

CHECK IGNITION

The electrode of the electronic ignition system

is positioned above the surface of the burner

base. Do not remove a burner cap or touch the

electrode of a burner while another is turned

on. Damage or electrical shock may occur.

A.Remove tape holding burners in position. Note

the position of one larger burner base, head and

cap. The large and regular size pieces are not

interchangeable.

B. Place burner heads over the burner base.

Make sure the hole in the burner head is properly

aligned with the electrode in the burner base.

C. Place the burner caps on the burner heads.

Make sure that the burner caps are properly

seated on the burner heads.

Burner cap not properly seated

Burner cap properly seated

Installation Instructions

Burner cap

Burner head

assembly

Burner

base

Electrode

ASSEMBLE BURNERS,

CHECK IGNITION (cont.)

D. Check igniters.

Operation of the electric igniters should

be tested after the cooktop and supply line

have been carefully checked for leaks and the

cooktop has been connected to the electrical

power.

• Push and turn a burner valve to the LITE

position. All spark igniters will make a series

of sparks (ticking sounds), but only the burner

turned to LITE will light.

– The burner should light when gas is available

to the burner.

– Once the burner lights, it should be turned to

another position.

• Test each valve separately until all burners have

been checked.

IMPORTANT: If the igniter electrodes continue to

spark after all of the burners are lit, check that

each burner component is assembled and

properly seated.

E. Burner ignition.

Cooktop Spark Ignition—When you turn the

cooktop knob to LITE, the spark igniter makes

a series of electric sparks (ticking sounds) which

light the burner. During a power failure, the

burners will not light automatically. In an

emergency, a cooktop burner may be lit

with a match by following the steps below.

WARNING: Lighting gas burners with

a match is dangerous. You should match light

the cooktop burners only in an emergency.

• Light a match and hold the flame near the

burner you want to light. Wooden matches

work best.

• Push in and turn the control knob slowly.

Be sure you are turning the correct knob

for the burner you are lighting.

NOTE: If the burner does not light within five

seconds, turn the knob off and wait one minute

before trying again.

Installation Instructions

ASSEMBLE BURNERS,

CHECK IGNITION (cont.)

F. Turn on each burner. On LP models, flames

should be blue in color but may have yellow

tips. Natural gas models should have soft, blue

flames. The burner flames should not flutter or

blow away from the burner. The flame should be

no less than 1/4″ on the lowest setting and no

greater than 1-1/2″ on highest setting.

WARNING:If you attempt to measure

the flame, please use caution. Burns could result.

G. Place the two side grates so that a continuous

“arc” is formed with the center ribs of both grates.

Make sure both grates are stable and level.

Burners should be checked frequently

Cooktop burner

1/4″ to

1-1/2″

OPERATION CHECKLIST

1. Make sure all controls are left in the OFF

position.

2. The serial plate for your cooktop is located

on the bottom of the burner box. In addition to

the model and serial numbers, it tells you the

ratings of the burners and the type of fuel and

pressure the cooktop was adjusted for when it

left the factory.

3. When ordering parts, always include the serial

number, model number and a code letter to

ensure proper replacement parts.

4. Check again to be sure all installation

procedures have been completed.

COOKTOP INSTALLATION WITH A

30″ MONOGRAM DOWNDRAFT VENT,

MODEL ZVB30

The installation of the downdraft vent with

this cooktop requires careful consideration.

Both the cooktop and the vent must be installed

according to each specific installation instruction.

BASE CABINET REQUIREMENTS

The combined installation will fit in a standard

24″ deep base cabinet. Use a 30″ or wider base

cabinet.

– The vent housing, blower and ductwork will

occupy the base cabinet.

COOKTOP REQUIREMENTS

The countertop must have a deep flat surface to

accommodate the cooktop and vent. Countertops

with a rolled front edge and backsplash will not

provide the flat surface area required.

• Review the illustration to determine the countertop

surface requirements.

– All cutout clearances for this installation must be

observed.

POWER SUPPLY

If local codes permit, the vent and cooktop may

operate from the same 120V, 15 amp duplex outlet.

Locate the gas and electrical supply as shown on

page 8.

22-3/8″

cutout

depth

19-5/8″

cooktop

cutout

depth

2-3/4″

30-3/4″

28-1/2″ vent cutout

1/8″

gap

2-7/8″ min. cooktop

cutout to rear vertical

combustible surface

23-7/8″

total flat

surface

required

at center

12″ min. cutout to

wall, both sides

2-1/2″ min. clearance

to cutout

Front edge of countertop

7/16″ cooktop overlap

(1-1/4″ at center)

Installation Options

28-1/2″ cooktop

area cutout

Installation Options

COOKTOP INSTALLATION OVER A

MONOGRAM WARMING DRAWER,

MODEL ZTD910 OR ZKD910

These cooktops may be installed over a 30″

or 27″ Warming Drawer. Both the cooktop and

the warming drawer must be installed according to

each specific installation instruction.

Use a 30″ or wider base cabinet.

• Plan gas supply location carefully to avoid

interference with the warming drawer.

POWER SUPPLY:

If local codes permit, the cooktop and warming

drawer may operate from the same 120V duplex

outlet. Refer to installation instructions for details.

Install 2x4 or 2x2 anti-tip block against

rear cabinet wall 9″ from cutout floor

to bottom of block

23-1/2″ min.

Cooktop 28-1/2″

19-5/8″

2-1/2″ min.

1-1/2″ cabinet top

5-1/2″ min.

NOTE: When installing a Monogram Warming Drawer

below a cooktop, a solid barrier must be installed at least

1″ from the lowest point of the bottom of cooktop

burner box to the top of cutout. See Warming Drawer

Installation Instructions for details.

36″

countertop

height

9-1/4″

25″

9″

Dim. A

ZTD910 28-1/2″

ZKD910 25-1/2″

COOKTOP INSTALLATION OVER A

27″ OR 30″ MONOGRAM SINGLE OVEN,

MODEL ZET1, ZEK938 OR ZET938

These cooktops may be installed over the

Monogram ZET1, ZEK938 or ZET938 single oven.

Both the cooktop and the oven must be installed

according to each specific installation instruction.

– Allow 4″ Min. clearance from the top of the

countertop to the top of the oven cutout.

Use a 30″ or wider base cabinet.

• For best appearance, the cooktop should be

centered over the oven.

POWER SUPPLY

The oven requires a separate, properly grounded

20 Amp, 3-wire 208 or 240 volt, 60 Hz power supply.

The cooktop requires a separate 120V power supply.

See page 8. Where codes permit, the gas shut-off

valve may be located in an adjacent cabinet or

other easily accessible location.

Use two 2x4’s or equivalent runners spaced 25″ centerline

to centerline in the opening and flush with top of toekick.

Or elevate the oven floor to desired height. The support must

be level, rigidly mounted and capable of supporting 200 lbs.

23-1/2″ min.

4″ high

toekick

Cooktop

28-1/2″

19-5/8″

2-1/2″ min.

1-1/2″ cabinet top

4″ min.

36″

countertop

height

25″

Installation Options

Ovens Dim. A Dim. B

30″ 28-1/2″ min. 27-1/4″ min.

28-5/8″ max. 27-5/16″ max.

27″ 25″ min. 27-5/8″ min.

25-1/4″ max. 28-1/8″ max.

ADJUST THE REGULATOR

A. Disconnect all electrical power, at the main circuit

breaker or fuse box.

B. Shut off the gas supply to the cooktop by closing the

manual shut-off valve.

C. Adjust the pressure regulator by the following

instructions:

• Unscrew the cap.

• Place your thumb against the flat side of the spring

retainer and press down to remove the retainer.

• Carefully look at the spring retainer to locate the NAT

or LP position.

• Turn the spring retainer over so that the desired gas is

showing on the bottom.

• Snap the retainer back into position.

• Screw the cap back onto the regulator.

CHANGE BURNER ORIFICES

INSTALLATION TIP: First remove all

orifices and then start replacing them.

This will help to prevent the possibility

that some may not be replaced.

A. Remove the burner grates,

burner caps and burner heads.

B. Using a 7mm nut driver, remove the

top burner orifices. There are two

orifices per burner.

The main orifice is

located low in the center

of the burner, while the

simmer orifice is located

higher beside the center

of the burner.

DOWN

FOR OFF

NAT

Gasket

Cap

Spring

retainer

L.P./propane

position

NAT.

position

Pressure regulator

Burner cap

Burner

head

Burner

base

Spark igniter

Main

orifice

Simmer

orifice

SAFETY INFORMATION

The pressure regulator and burner orifices are set for

natural gas operation.

To convert this cooktop from natural gas operation to

LP operation, the regulator and burner orifices must be

converted. LP burner orifices are attached to the regulator.

CAUTION — The cooktop, as shipped from the

factory, is set for use with its intended gas. If you wish

to use your cooktop with the alternate gas, you must

first replace the orifices and convert the pressure

regulator.

WARNING — This conversion must be

performed by a qualified installer or gas supplier in

accordance with the manufacturer’s instructions and

all codes and requirements of the authority having

jurisdiction. Failure to follow instructions could result in

serious injury or property damage. The qualified agency

performing this work assumes responsibility for the

conversion.

CAUTION — The following adjustments must

be made before turning on the burner. Failure to do so

could result in serious injury. Be sure pressure regulator

has been converted as described in Step 1.

TOOLS YOU WILL NEED FOR

CONVERSION

Safety glasses

Small flat-head

screwdriver

(2 to 2.4 mm or

3/32″ tip size,

60 mm long)

Crescent wrench

7mm nutdriver

Installation Convert Natural Gas Model ZGU384NSMSS

Instructions

to LP Gas Operation

ADJUST BURNER FLAMES

A. Turn all burners on highest setting and check the flames.

They should be blue in color and may have some yellow

tipping at the ends of the flame when using LP gas.

Foreign particles in the gas line may cause an orange

flame at first, but this will soon disappear.

B. Turn the cooktop burner knob to “LO” while observing

the flame.

Adjust the setting of the upper row of flames using the

valve bypass screw as follows:

Adjustments must be made with two other burners in

operation on a medium setting. This prevents the upper row

of flames from being set too low, resulting in the flame

being extinguished when other burners are turned on.

C. To adjust the flame, remove the knobs. Insert a screwdriver

through the access hole in valve shaft as shown.

• If the flames were too small or fluttered, open the valve

more than the original setting.

• If the flames blew away from the burner, close the valve

more than the original setting.

D. Make the adjustment by slowly turning the screw until

flame appearance is correct.

E. Testing Flame Stability:

Test 1 – Turn the knob from “HI” to “LO” quickly.

If the upper row of flames goes out at this setting,

increase the flame size and test again.

Test 2 – With the burner on “LO”, open and close the

cabinet door under the cooktop. If the flame is

extinguished by the air currents created by the

door movement, increase the flame height and

test again.

NOTE: When the burner is on the “SIM” setting, the upper

row of flames will go out.

F. Flame Recheck:

After the adjustment is made, turn all burners off. Ignite

each burner individually. Observe the flame at the “HI”

position. Rotate the knob to the lowest setting and be

sure that the flame size decreases as the knob is

rotated counterclockwise.

Once the conversion is complete and checked ok,

fill out the conversion sticker and include your name,

organization and date conversion was made. Apply

the sticker near the cooktop gas inlet opening to

alert others in the future that this appliance has been

converted. If converting back to the original gas, please

remove the sticker so others know the appliance is set

to use its original gas.

CHANGE BURNER ORIFICES (cont.)

IMPORTANT: Orifices must be located exactly as shown.

Carefully read and observe each orifice label for correct

location.

C. Install the proper orifices in the exact locations as noted

in the illustrations above.

D. Return the natural gas orifices to the bracket and

reattach the bracket and the instruction sheet to the

pressure regulator using the screw removed previously.

E. Replace the burner bases, heads, caps and top grates.

SIMMER

ORIFICES

Installation Instructions for Natural to LP Gas Conversion

MAIN

ORIFICES

The 34SL and

51SN are for all

four burners.

Installation Convert LP Gas Model ZGU384LSMSS

Instructions

to Natural Gas Operation

ADJUST THE REGULATOR

A. Disconnect all electrical power, at the main circuit

breaker or fuse box.

B. Shut off the gas supply to the cooktop by closing the

manual shut-off valve.

C. Adjust the pressure regulator by the following

instructions:

• Unscrew the cap.

• Place your thumb against the flat side of the spring

retainer and press down to remove the retainer.

• Carefully look at the spring retainer to locate the NAT

or LP position.

• Turn the spring retainer over so that the desired gas is

showing on the bottom.

• Snap the retainer back into position.

• Screw the cap back onto the regulator.

CHANGE BURNER ORIFICES

INSTALLATION TIP: First remove all

orifices and then start replacing them.

This will help to prevent the possibility

that some may not be replaced.

A. Remove the burner grates,

burner caps and burner heads.

B. Using a 7mm nut driver, remove the

top burner orifices. There are two

orifices per burner.

The main orifice is

located low in the center

of the burner, while the

simmer orifice is located

higher beside the center

of the burner.

DOWN

FOR OFF

NAT

Gasket

Cap

Spring

retainer

L.P./propane

position

NAT.

position

Pressure regulator

Burner cap

Burner

head

Burner

base

Spark igniter

Main

orifice

Simmer

orifice

SAFETY INFORMATION

The pressure regulator and burner orifices are set for

Liquid Propane (LP) gas operation.

To convert this cooktop from LP gas operation to

natural gas operation, the regulator and burner orifices

must be converted. Natural gas burner orifices are

attached to the regulator.

CAUTION — The cooktop, as shipped from the

factory, is set for use with its intended gas. If you wish

to use your cooktop with the alternate gas, you must

first replace the orifices and convert the pressure

regulator.

WARNING — This conversion must be

performed by a qualified installer or gas supplier in

accordance with the manufacturer’s instructions and

all codes and requirements of the authority having

jurisdiction. Failure to follow instructions could result in

serious injury or property damage. The qualified agency

performing this work assumes responsibility for the

conversion.

CAUTION — The following adjustments must

be made before turning on the burner. Failure to do so

could result in serious injury. Be sure pressure regulator

has been converted as described in Step 1.

TOOLS YOU WILL NEED FOR

CONVERSION

Safety glasses

Small flat-head

screwdriver

(2 to 2.4 mm or

3/32″ tip size,

60 mm long)

Crescent wrench

7mm nutdriver

ADJUST BURNER FLAMES

A. Turn all burners on highest setting and check the flames.

They should be blue (no yellow tipping) when using

natural gas. Foreign particles in the gas line may cause

an orange flame at first, but this will soon disappear.

B. Turn the cooktop burner knob to “LO” while observing

the flame.

Adjust the setting of the upper row of flames using the

valve bypass screw as follows:

Adjustments must be made with two other burners in

operation on a medium setting. This prevents the upper row

of flames from being set too low, resulting in the flame

being extinguished when other burners are turned on.

C. To adjust the flame, remove the knobs. Insert a screwdriver

through the access hole in valve shaft as shown.

• If the flames were too small or fluttered, open the valve

more than the original setting.

• If the flames blew away from the burner, close the valve

more than the original setting.

D. Make the adjustment by slowly turning the screw until

flame appearance is correct.

E. Testing Flame Stability:

Test 1 – Turn the knob from “HI” to “LO” quickly.

If the upper row of flames goes out at this setting,

increase the flame size and test again.

Test 2 – With the burner on “LO”, open and close the

cabinet door under the cooktop. If the flame is

extinguished by the air currents created by the

door movement, increase the flame height and

test again.

NOTE: When the burner is on the “SIM” setting, the upper

row of flames will go out.

F. Flame Recheck:

After the adjustment is made, turn all burners off. Ignite

each burner individually. Observe the flame at the “HI”

position. Rotate the knob to the lowest setting and be

sure that the flame size decreases as the knob is

rotated counterclockwise.

Once the conversion is complete and checked ok,

fill out the conversion sticker and include your name,

organization and date conversion was made. Apply

the sticker near the cooktop gas inlet opening to

alert others in the future that this appliance has been

converted. If converting back to the original gas, please

remove the sticker so others know the appliance is set

to use its original gas.

CHANGE BURNER ORIFICES (cont.)

IMPORTANT: Orifices must be located exactly as shown.

Carefully read and observe each orifice label for correct

location.

C. Install the proper orifices in the exact locations as noted

in the illustrations above.

D. Return the LP gas orifices to the bracket and reattach

the bracket and the instruction sheet to the pressure

regulator using the screw removed previously.

E. Replace the burner bases, heads, caps and top grates.

SIMMER

ORIFICES

MAIN

ORIFICES

Installation Instructions for LP to Natural Gas Conversion

The 34SL and

51SN are for all

four burners.

La section Française

AVANT DE COMMENCER

Avant de commencer, lisez attentivement la

totalité de ces instructions.

•

IMPORTANT — Conservez ces

instructions pour votre inspecteur local.

•

IMPORTANT — Respectez toutes les

ordonnances et les codes locaux.

• Note à l’installateur – Assurez-vous de laissez

ces instructions au consommateur.

• Note au consommateur – Conservez ces

instructions pour référence future.

• La garantie ne couvre aucune panne due à une

mauvaise installation.

AVERTISSEMENT —

Cet appareil doit être bien mis à la terre.

•

IMPORTANT — Vous devez vérifier que

cet appareil n’ait pas de fuite conformément aux

instructions du fabricant.

• L’installateur est responsable d’une bonne

installation et la garantie ne couvre aucune

panne due à une mauvaise installation.

POUR VOTRE SÉCURITÉ

AVERTISSEMENT —

Si vous ne suivez pas exactement les instructions

de ce manuel, vous risquez d’occasionner un

incendie, une explosion ou une fuite de gaz, qui

peuvent provoquer des dommages matériels,

des blessures corporelles ou la mort.

Ne conservez pas ou n'utilisez jamais

d'essence ou d'autres liquides ou vapeurs

inflammables à proximité de cet appareil

ou de tout autre appareil ménager!

CI QUE VOUS DEVEZ FAIRE SI

VOUSSENTEZ LE GAZ:

• N’essayez jamais d’allumer un appareil

électroménager. Ne touchez à aucun

commutateur d’électricité, n’utilisez jamais

un téléphone dans votre bâtiment.

• Appelez immédiatement votre fournisseur de

gaz à l’aide du téléphone d’un voisin. Suivez les

instructions de votre fournisseur de gaz.

• Si vous ne pouvez pas entrer en contact avec

votre fournisseur de gaz, appelez les pompiers.

L’installation et le service de votre table de cuisson

doivent être faits par un installateur qualifié, un

technicien de service ou votre fournisseur de gaz.

Information de la sécurité

Information de la sécurité
20
AVERTISSEMENT — Débranchez
tout courant électrique au niveau du disjoncteur de
la maison ou de la boîte à fusibles avant d’installer.
La conception de votre table de cuisson a été
approuvé par Underwriters Laboratories. Vous
trouverez des précautions à prendre en matière de
sécurité dans votre Guide d’utilisation et de soins.
Lisez-les attentivement.
• L’installation de votre table de cuisson doit se
conformer aux codes locaux ou, en l’absence de
codes locaux, au National Fuel Gas Code, ANSI
Z223.1/NFPA 54 Dernière édition.
• Assurez-vous que votre table de cuisson soit bien
installée par un installateur qualifié ou un
technicien de service.
• Pour éliminer tout mouvement corporel au dessus
des brûleurs de votre table de cuisson, évitez de
placer des armoires de cuisine au dessus des
brûleurs.
• N’installez jamais votre appareil près d’une porte
d’entrée ou dans un emplacement où un courant
d’air peut gêner son usage.
BESOINS D’ÉLECTRICITÉ
Cet appareil ménager doit être livré avec le bon
voltage et la bonne fréquence et branché à son
propre circuit de dérivation bien mis à la terre,
protégé par un disjoncteur ou un fusible qui ont
l’ampérage noté sur la plaque minéralogique de
votre appareil. 
Nous vous recommandons de faire brancher le
câblage électrique et la fiche de votre cuisinière par
un électricien qualifié. Après l’installation,
demandez à l’électricien de vous montrer
l’emplacement de votre coupe-circuit principal.
Demandez à votre entreprise de services publics les
codes électriques en vigueur dans votre région. En
ne câblant pas votre cuisinière conformément aux
codes en vigueur, vous provoquez une situation
dangereuse. En l’absence de codes, vous devez
câbler et isoler votre cuisinière conformément 
aux exigences du Canadian Electrical Code.
CONTENU
Préparation à l’installation
Modèles disponibles  . . . . . . . . . . . . . . . . . . . .21
Pièces comprises . . . . . . . . . . . . . . . . . . . . . . . 21
Matériaux dont vous pourriez 
avoir besoin . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Outils dont vous aurez besoin   . . . . . . . . . . 21
Options d'installation et de planification  . 22
Liste de vérification de pré-installation  . . 23
Dimensions et dégagements   . . . . . . . . . . . 24
Emplacements de l'alimentation de gaz  . 25
Instructions d’installation
Instructions étape par étape  . . . . . . . . 26–28
Liste de vérification de fonctionnement  . . 28
Choix d’installation
Installation avec un évent descendant  . . 29
Installation sur un tiroir 
chauffe-aliments   . . . . . . . . . . . . . . . . . . . . . . 30
Installation sur un four simple   . . . . . . . . . . 31
Instructions d'installation pour 
la conversion du gaz naturel au gaz PL
Outils dont vous aurez besoin   . . . . . . . . . . 32
Ajuster le régulateur   . . . . . . . . . . . . . . . . . . . 32
Changer les orifices   . . . . . . . . . . . . . . . . 32, 33
Ajuster les flammes du brûleur   . . . . . . . . . 33
Instructions d’installation pour 
la conversion du gaz PL au gaz naturel
Outils dont vous aurez besoin . . . . . . . . . . . 34
Ajuster le régulateur   . . . . . . . . . . . . . . . . . . . 34
Changer les orifices  . . . . . . . . . . . . . . . . . 34, 35
Ajuster les flammes du brûleur . . . . . . . . . . 35