Hitachi H 30PV Safety Instructions And Instruction Manual

Marque: Hitachi

Modèle: H 30PV

Taper: Safety Instructions And Instruction Manual

Ce manuel convient également à

H 45MA

English

H 45MA

MODEL DEMOLITION HAMMER

MODELE MARTEAU PIQUEUR

MODELO MARTILLO DEMOLEDOR

DOUBLE INSULATION

DOUBLE ISOLATION

AISLAMIENTO DOBLE

MODE D’EMPLOI ET INSTRUCTIONS DE SECURITE

AVERTISSEMENT

Une utilisation incorrecte et dangereuse de cet outil motorisé peut entraîner la

mort ou de sérieuses blessures corporelles!

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de

ce produit. Prière de lire et de comprendre ce mode d’emploi avant d’utiliser l’outil

motorisé. Garder ce mode d’emploi à la disponibilité des autres utilisateurs avant

qu’ils utilisent l’outil motorisé.

INSTRUCTION MANUAL AND SAFETY INSTRUCTIONS

WARNING

Improper and unsafe use of this power tool can result in death or serious bodily

injury!

This manual contains important information about product safety. Please read

and understand this manual before operating the power tool. Please keep this

manual available for others before they use the power tool.

MANUAL DE INSTRUCCIONES E INSTRUCCIONES DE SEGURIDAD

ADVERTENCIA

¡La utilización inapropiada e insegura de esta herramienta eléctrica puede resultar

en lesiones serias o en la muerte!

Este manual contiene información importante sobre la seguridad del producto.

Lea y comprenda este manual antes de utilizar la herramienta eléctrica. Guarde

este manual para que puedan leerlo otras personas antes de que utilicen la

herramienta eléctrica.

English

CONTENTS

English

Page

IMPORTANT INFORMATION ............. 3

MEANINGS OF SIGNAL WORDS ...... 3

SAFETY

IMPORTANT SAFETY INSTRUCTIONS

FOR USING ALL POWER TOOLS ..................

IMPORTANT SAFETY INSTRUCTIONS

FOR USE OF THE DEMOLITION HAMMER...

REPLACEMENT PARTS ...................... 7

POLARIZED PLUGS ............................ 7

USE OF EXTENSION CORD ............... 8

DOUBLE INSULATION FOR SAFER OPERATION

..... 9

Page

OPERATION AND MAINTENANCE

NAME OF PARTS.............................. 10

SPECIFICATIONS .............................. 10

ACCESSORIES .................................. 11

STANDARD ACCESSORIES ......... 11

OPTIONAL ACCESSORIES ........... 11

APPLICATIONS ................................. 13

PRIOR TO OPERATION..................... 13

HOW TO USE THE DEMOLITION HAMMER

..... 15

HOW TO REPLACE GREASE............ 15

MAINTENANCE AND INSPECTION

.... 16

SERVICE AND REPAIRS ................... 16

TABLE DES MATIERES

Français

Page

INFORMATIONS IMPORTANTES .... 17

SIGNIFICATION DES MOTS D’AVERTISSEMENT

.. 17

SECURITE

CONSIGNES DE SECURITE IMPORTANTES POUR

L’UTILISATION DE TOUS LES OUTILS ELECTRIQUES

...

CONSIGNES DE SECURITE IMPORTANTES

POUR L’UTILISATION DU MARTEAU PIQUEUR

PIECES DE RECHANGE .................... 22

FICHE POLARISEES .......................... 22

CORDON DE RALLONGE ................. 23

DOUBLE ISOLATION POUR UN

FONCTIONNEMENT PLUS SUR

........ 24

Page

UTILISATION ET ENTRETIEN

NOM DES PIECES............................. 25

FICHE TECHNIQUE ........................... 25

ACCESSOIRES .................................. 26

ACCESSOIRES STANDARD ......... 26

ACCESSOIRES EN OPTION.......... 26

APPLICATIONS ................................. 28

AVANT L’UTILISATION .................... 28

UTILISATION DU MARTEAU PIQUEUR

.... 30

REMPLACEMENT DE LA GRAISSE

....... 30

ENTRETIEN ET INSPECTION ........... 31

SERVICE APRES-VENTE ET REPARATIONS

..... 31

ÍNDICE

Español

Página

INFORMACIÓN IMPORTANTE......... 32

SIGNIFICADO DE LAS PALABRAS DE SEÑALIZACIÓN

.. 32

SEGURIDAD

INSTRUCCIONES IMPORTANTES DE SEGURIDAD PARA

UTILIZACIÓN DE TODAS LAS HERRAMIENTAS ELÉCTRICAS

.. 33

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

PARA UTILIZACIÓN DEL MARTILLO DEMOLEDOR

.. 37

PIEZAS DE REEMPLAZO .................. 37

ENCHUFES POLARIZADOS ............. 37

UTILIZACIÓN DE UN CABLE PROLONGADOR

...... 38

AISLAMIENTO DOBLE PARA OFRECER UNA

OPERACIÓN MÁS SEGURA.........................

Página

OPERACIÓN Y MANTENIMIENTO

NOMENCLATURA ............................ 40

ESPECIFICACIONES ......................... 40

ACCESORIOS .................................... 41

ACCESORIOS ESTÁNDAR............ 41

ACCESORIOS OPCIONALES ........ 41

APLICACIONES ................................. 43

ANTES DE LA OPERACIÓN.............. 43

FORMA DE UTILIZAR EL MARTILLO DEMOLEDOR

.. 45

FORMA DE REEMPLAZAR LA GRASA

.. 45

MANTENIMIENTO E INSPECCIÓN.. 46

SERVICIO Y REPARACIONES .......... 46

English

IMPORTANT INFORMATION

Read and understand all of the operating instructions, safety precautions and warnings in

the Instruction Manual before operating or maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused by the

failure to observe basic safety rules or precautions. An accident can often be avoided by

recognizing a potentially hazardous situation before it occurs, and by observing appropriate

safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual and

in the sections which contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identified by

WARNINGS on the power tool and in this Instruction Manual.

Never use this power tool in a manner that has not been specifically recommended by

HITACHI, unless you first confirm that the planned use will be safe for you and others.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could result in

serious personal injury.

CAUTION indicates a hazardous situations which, if ignored, could result in moderate

personal injury, or could cause machine damage.

NOTE emphasizes essential information.

English

SAFETY

INPORTANT SAFETY INSTRUCTIONS

FOR USING ALL POWER TOOLSaaaa

WARNING: Death or serious bodily injury could result from improper or unsafe use

of power tools. To avoid these risks, follow these basic safety instruc-

tions:

READ ALL INSTRUCTIONS

1. NEVER TOUCH MOVING PARTS.

Never place your hands, fingers or other body parts near the tool’s moving parts.

2. NEVER OPERATE WITHOUT ALL GUARDS IN PLACE.

Never operate this tool without all guards or safety features in place and in proper working

order. If maintenance or servicing requires the removal of a guard or safety feature, be sure

to replace the guard or safety feature before resuming operation of the tool.

3. ALWAYS WEAR EYE AND EAR PROTECTOR.

Protect yourself from flying or expelled wood chips, metal particles or other debris by

using protective goggles or equivalent eye protector. Wear ear protector to protect

yourself from excessive noise.

4. PROTECT YOURSELF AGAINST ELECTRIC SHOCK.

Prevent body contact with grounded surfaces such as pipes, radiators, ranges and

refrigeration enclosures. Never operate the tool in damp or wet locations.

5. DISCONNECT TOOLS.

Never leave the tool connected to a power source. Always disconnect the tool from its

power source before servicing, inspecting, maintaining, cleaning and before changing or

checking any parts.

6. AVOID UNINTENTIONAL STARTING.

Don’t carry the tool while it is connected to its power source. Don’t carry the tool with your

finger near the power switch. Be sure the power switch is in the “off” position before

connecting the tool to its power source.

7. STORE TOOL PROPERLY.

When not in use, the tool should be stored in a dry place. Keep out of reach of children.

Lock-out the storage area.

8. KEEP WORK AREA CLEAN.

Cluttered areas and benches invite injuries. Clear all work areas and work benches of

unnecessary tools, debris, furniture, etc.

9. CONSIDER WORK AREA ENVIRONMENT.

Don’t expose power tools to rain. Don’t use power tools in damp or wet locations. Keep

work area well lit and well ventilated.

Don’t use tool in presence of flammable liquids or gases.

Power tools produce sparks during operation. They also spark when switching ON/

OFF. Never use power tools in sites containing lacquer, paint, benzine, thinner,

gasoline, gases, adhesive agents, and other materials which are combustible or

explosive.

English

10.KEEP CHILDREN AWAY.

Do not let visitors contact tool or extension cord.

All visitors should be kept safely away from work area.

11.DON’T FORCE TOOL.

It will do the job better and safer at the rate for which it was intended.

12.USE RIGHT TOOL.

Don’t force small tool or attachment to do the job of a heavy-duty tool.

Don’t use tool for purpose not intended —for example— don’t use circular saw for cutting

tree limbs or logs.

13.DRESS PROPERLY.

Do not wear loose clothing or jewelry. They can be caught in moving parts.

Rubber gloves and non-skid footwear are recommended when working outdoors.

Wear protective hair covering to contain long hair.

14.USE FACE, DUST MASK OR RESPIRATOR IF OPERATION IS DUSTY.

All persons in the area where power tools are being operated should also wear face, dust

mask or respirator.

15.DON’T ABUSE CORD.

Never carry tool by cord or yank it to disconnect from receptacle.

Keep cord from heat, oil and sharp edges.

16.SECURE WORK.

Use clamps or a vise to hold work. It’s safer than using your hand and it frees both hands

to operate tool.

17.DON’T OVERREACH.

Keep proper footing and balance at all times.

18.MAINTAIN TOOLS WITH CARE.

Keep tools sharp and clean for better and safer performance.

Follow instructions for lubricating and changing accessories.

Inspect tool cords periodically and if damaged, have repaired by an authorized service

center. Inspect extension cords periodically and replace if damaged.

Keep handles dry, clean, and free from oil and grease.

19.REMOVE ADJUSTING KEYS AND WRENCHES.

Keys and adjusting wrenches remove from tool before turning it on.

20.OUTDOOR USE EXTENSION CORD.

When tool is used outdoors, use only extension cord intended for use outdoors and so

marked.

21.STAY ALERT.

Watch what you are doing. Use common sense. Do not operate tool when you are tired.

Tools should never be used by you if you are under the influence of alcohol, drugs or

medication that makes you drowsy.

22.CHECK DAMAGED PARTS.

Before further use of the tool, a guard or other part that is damaged should be carefully

checked to determine that it will operate properly and perform its intended function.

Check for alignment of moving parts, binding of moving parts, breakage of parts,

mounting, and any other conditions that may affect its operation.

A guard or other part that is damaged should be properly repaired or replaced by an

authorized service center unless otherwise indicated elsewhere in this Instruction

Manual.

Have defective switches replaced by the authorized service center.

Do not use tool if switch does not turn it on and off.

English

23.NEVER USE A POWER TOOL FOR APPLICATIONS OTHER THAN THOSE SPECIFIED.

Never use a power tool for applications other than those specified in the Instruction

Manual.

24.HANDLE TOOL CORRECTLY.

Operate the tool according to the instructions provided herein. Do not drop or throw the

tool. Never allow the tool to be operated by children, individuals unfamiliar with its

operation or unauthorized personnel.

25.CHECK FOR LIVE WIRES.

Avoid the risk of severe electrical shock by checking for live electrical wires that may be

buried in walls, floors or ceilings. The wires should be de-energized before work begins.

26.KEEP ALL SCREWS, BOLTS AND COVERS TIGHTLY IN PLACE.

Keep all screws, bolts, and plates tightly mounted. Check their condition periodically.

27.DO NOT USE POWER TOOLS IF THE PLASTIC HOUSING OR HANDLE IS CRACKED.

Cracks in the tool’s housing or handle can lead to electric shock. Such tools should not

be used until repaired.

28.BLADES AND ACCESSORIES MUST BE SECURELY MOUNTED TO THE TOOL.

Prevent potential injuries to youself or others. Blades, cutting implements and accessories

which have been mounted to the tool should be secure and tight.

29.KEEP MOTOR AIR VENT CLEAN.

The tool’s motor air vent must be kept clean so that air can freely flow at all times. Check

for dust build-up frequently.

30.OPERATE POWER TOOLS AT THE RATED VOLTAGE.

Operate the power tool at voltages specified on its nameplate.

If using the power tool at a higher voltage than the rated voltage, it will result in

abnormally fast motor revolution and may damage the unit and the motor may burn out.

31.NEVER USE A TOOL WHICH IS DEFECTIVE OR OPERATING ABNORMALLY.

If the tool appears to be operating unusually, making strange noises, or otherwise

appears defective, stop using it immediately and arrange for repairs by a Hitachi

authorized service center.

32.NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF.

Don’t leave tool until it comes to a complete stop.

33.CAREFULLY HANDLE POWER TOOLS.

Should a power tool be dropped or struck against hard materials inadvertently, it may be

deformed, cracked, or damaged.

34.DO NOT WIPE PLASTIC PARTS WITH SOLVENT.

Solvents such as gasoline, thinner benzine, carbon tetrachloride, and alcohol may

damage and crack plastic parts. Do not wipe them with such solvents.

Wipe plastic parts with a soft cloth lightly dampened with soapy water and dry

thoroughly.

35.USE ONLY GENUINE HITACHI REPLACEMENT PARTS.

Replacement parts not manufactured by Hitachi may void your warranty and can lead to

malfunction and resulting injuries. Genuine Hitachi parts are available from your dealer.

English

IMPORTANT SAFETY INSTRUCTIONSaEL

FOR USE OF THE DEMOLITION HAMMER

WARNING: Death or serious bodily injury could result from improper or unsafe use

of the demolition hammer. To avoid these risks, follow these basic

safety instructions:

1. NEVER touch the tool bit with bare hands after operation.

2. NEVER wear gloves made of stuff liable to roll up such as cotton, wool, cloth or string,

etc.

3. ALWAYS attach the side handle and securely grip the Demolition Hammer.

4. ALWAYS wear eye and ear protectors during operation.

5. ALWAYS be careful with buried object such as an underground wiring.

Touching these active wiring or electric cable with this tool, you may receive an electric

shock.

Comfirm if there are any buried object such as electric cable within the wall, floor or

ceiling where you are going to operate here after.

REPLACEMENT PARTS

When servicing use only identical replacement parts.

Repairs should be conducted only by a Hitachi authorized service center.

POLARIZED PLUGS

To reduce the risk of electrick shock, this equipment has a polarized plug (one blade is wider

than the other).

This plug will fit in a polarized outlet only one way.

If the plug does not fit fully in the outlet, reverse the plug.

If it still does not fit, contact a qualified electrician to install the proper outlet.

Do not change the plug in any way.

English

USE OF EXTENSION CORD

Make sure your extension cord is in good condition. When using an extension cord, be sure

to use one heavy enough to carry the current your product will draw.

An undersized cord will cause a drop in line voltage resulting in loss of power and

overheating. Table shows the correct size to use depending on cord length and nameplate

ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the

heavier the cord.

MINIMUM GAGE FOR CORD SETS

Total Length of Cord in Feet (Meter)

0 – 25 26 – 50 51 – 100 101 – 150

(0 – 7.6) (7.9 – 15.2) (15.5 – 30.5) (30.8 – 45.7)

Ampere Rating AWG

More Not More

Than Than

0 – 618161614

6 – 10 18 16 14 12

10 – 12 16 16 14 12

12 – 16 14 12 Not Recommended

WARNING: Avoid electrical shock hazard. Never use this tool with a damaged or

frayed electrical cord or extension cord.

Inspect all electrical cords regularly. Never use in or near water or in any

environment where electric shock is possible.

English

DOUBLE INSULATION FOR SAFER OPERATION

To ensure safer operation of this power tool, HITACHI has adopted a double insulation

design. “Double insulation “ means that two physically separated insulation systems have

been used to insulate the electrically conductive materials connected to the power supply

from the outer frame handled by the operator. Therefore, either the symbol “ ” or the words

and “Double insulation” appear on the power tool or on the nameplate.

Although this system has no external grounding, you must still follow the normal electrical

safety precautions given in this Instruction Manual, including not using the power tool in wet

environments.

To keep the double insulation system effective, follow these precautions:

䡬 Only HITACHI AUTHORIZED SERVICE CENTER should disassemble or assemble this

power tool, and only genuine HITACHI replacement parts should be installed.

䡬 Clean the exterior of the power tool only with a soft cloth moistened with soapy water,

and dry thoroughly.

Never use solvents, gasoline or thinners on plastic components; otherwise the plastic

may dissolve.

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO

OTHER USERS OF THIS TOOL!

English

OPERATION AND MAINTENANCE

NOTE:

The information contained in this Instruction Manual is designed to assist you in the safe

operation and maintenance of the power tool.

Some illustrations in this Instruction Manual may show details or attachments that differ

from those on your own power tool

NAME OF PARTS

Fig. 1

SPECIFICATIONS

Motor Single-Phase, Series Commutator Motor

Power Source Single-Phase, 115V AC 60Hz

Current 8A

Full-load Impact Rate 3,000/min.

Weight 11.9 lbs (5.4 kg)

Front Cap

Grip (A)

Grip (B)

Housing

Brush Cap

(Under the Tail Cover)

Side Handle

Nameplate

Trigger Switch

English

ACCESSORIES

WARNING: Accessories for this power tool are mentioned in this Instruction

Manual.

The use of any other attachment or accessory can be dangerous and

could cause injury or mechanical damage.

STANDARD ACCESSORIES

(1) Bull Point (SDS max shank) (Code No. 313471)................................................................ 1

(2) Case (Code No. 314875) ...................................................................................................... 1

(3) Side Handle (Code No. 981870).......................................................................................... 1

(4) Allen Wrench (for 6 mm screw) (Code No. 944459) ......................................................... 1

(5) Allen Wrench (for 5 mm screw) (Code No. 944458) ......................................................... 1

OPTIONAL ACCESSORIES....... sold separately

䡬 Crushing

(1) Bull Point (SDS max shank type)

Overall Length 11-1/32" (280 mm) 15-3/4" (400 mm)

Code No. 313471 313472

䡬 Groove digging and edging

(1) Cold chisel (SDS max shank type)

Overall Length 11-1/32" (280 mm) 15-3/4" (400 mm)

Code No. 313473 313474

English

䡬 Asphalt Cutting

(1) Cutter (SDS max shank type)

Overall Length 15-3/4" (400 mm)

Code No. 313475

䡬 Scooping Work

(1) Scoop (SDS max shank type)

Overall Length 15-3/4" (400 mm)

Code No. 313476

䡬 Surface Roughing

(1) Bushing Tool

(Code No. 313477)

(2) Shank

(Code No. 313479)

䡬 Tamping

(1) Rammer

(Code No. 313478)

(2) Shank

(Code No. 313479)

English

䡬 Hammer Grease A

70g (in a tube) (Code No. 981840)

30g (in a tube) (Code No. 308471)

NOTE:

Accessories are subject to change without any obligation on the part of the HITACHI.

APPLICATIONS

䡬 Breaking concrete, chipping off concrete, grooving, bar cutting, and driving piles.

Application examples:

Installation of piping and wiring, sanitary facility installation, machinery installation,

water supply and drainage work, interior jobs, harbor facilities and other civil engineering

work.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms to the power source requirements

specified on the product nameplate.

2. Power switch

Ensure that the switch is in the OFF position. If the plug is connected to a receptacle while

the switch is in the ON position, the power tool will start operating immediately and can

cause serious injury.

3. Extension cord

When the work area is far away from the power source, use an extension cord of sufficient

thickness and rated capacity. The extension cord should be kept as short as practicable.

WARNING: Damaged cord must be replaced or repaired.

4. Check the receptacle

If the receptacle only loosely accepts the plug, the receptacle must be repaired. Contact

a licensed electrician to make appropriate repairs.

If such a fautly receptacle is used, it may cause overheating, resulting in a serious hazard.

5. Confirming condition of the environment:

Confirm that the work site is placed under appropriate conditions conforming to

prescribed precautions.

English

6. Installing Tools

NOTE:

When using tools such as bull points,

cutters, etc., make sure to use the genuine

parts designated by our company.

(1) Clean the shank portion of the tool.

(2) As shown in Fig. 2, pull grip (A) in the

direction of

, and insert the tool into a

hole of the front cap in a state where it is

further turned in the direction of

(3) Adjust the groove position while turning

the tool, and furthermore insert it until it

hits the end of the hole.

(4) Return grip (A) to its original position, pull

the tool and make sure it is locked

completely. (Fig. 3)

7. Deciding Working Position of Tool

The tool can be turned every 30 degrees

and can be fixed at the position of 12 steps.

(1) As shown in Fig. 4, if the grip (A) is turned

in the direction of

in a state where the

grip (B) is turned 60 degrees in the direction

, the blade angle can be changed

freely to any desired position.

(2) As shown in Fig. 5, if grip (B) is turned 60

degrees in the direction of

, the holding

part of the tool automatically turns 30

degrees. If this action is repeated, the blade

angle of the tool can be changed by every

30 degrees.

(3) Release grip (B) and turn the tool, and

make sure that it is locked completely.

8. Removing Tool

As shown in Fig. 2, pull grip (A), and pull

out the tool in a state where it is further

turned in the direction of

Fig. 2

Fig. 3

Fig. 4

Fig. 5

Grip (A)

Front Cap

Tool

Shank

Grip (A)

Grip (B)

English

CAUTION: After long time of use, the front cover becomes hot.

Therefore, be careful not to burn your hands.

GREASE REPLACEMENT

This machine is of full air-tight construction to protect against dust and to prevent lubricant

leakage. This machine can be used without grease supplement for an extended period of

time. However, perform the grease replacement to maintain the service life. Replace the

grease as described below.

1. Grease Replacement Period

Inspect the grease amount according to the timing replacement period of the carbon

brush. (See item 3 in the section MAINTENANCE AND INSPECTION.)

Ask for grease replacement at the nearest authorized Hitachi Service Center.

In the case that you are forced to change the grease by yourself, please follow the

following points.

2. How to replace grease

CAUTION:

䡬 Before replacing the grease, turn the power off and pull out the plug from the receptacle.

Fig. 7

Crank Cover

1. After placing the tip of the tool in the base

hole, switch ON.

2. By utilizing the empty weight of the machine

and by firmly holding the hammer with

both hands, one can effectively control the

subsequent recoil motion.

Proceed at a moderate work-rate, the use

of too much force will impair efficiency.

HOW TO USE THE DEMOLITION HAMMER

Fig. 6

(1) Remove the crank cover and wipe off the

old grease inside.

(2) Supply 1 oz (30g) (the standard volume to

cover the connecting rod) of Hitachi Electric

Hammer Grease A to the crank case.

(3) After replacing the grease, install the crank

cover securely.

NOTE:

䡬 The Hitachi Electric Hammer Grease A is of

the low viscosity type. When the grease is

consumed, purchase from an authorized

Hitachi Service Center.

䡬 Do not excessively supply the designated

amount of grease. Otherwise, the tool

should not operate accurately.

English

MAINTENANCE AND INSPECTION

WARNING: Be sure to switch power OFF and disconnect the plug from the receptacle

during maintenance and inspection.

1. Inspecting the tool

Since use of a dull tool will degrade efficiency and cause possible motor malfunction,

sharpen or replace the tool as soon as abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that they are properly tightened.

Should any of the screws be loosened, retighten them immediately.

WARNING: Using this demolition hammer with loosen screws is extremely

dangerous.

3. Inspecting the carbon brushes (Fig. 8)

The Motor employs carbon brushes which

are consumable parts. When they become

worn to or near the “wear limit”, it could

result in motor trouble. When an auto-stop

carbon brush is equipped, the motor will

stop automatically. At that time, replace

both carbon brushes with new ones which

have the same carbon brush Numbers

shown in the figure. In addition, always

keep carbon brushes clean and ensure that

they slide freely within the brush holders.

NOTE: Use HITACHI carbon brush No. 73 indicated in Fig. 8.

4. Replacing carbon brushes (Refer to figure for name of parts)

Loosen the set screw then remove the tail cover. By loosening the brush cap, the carbon

brushes can be removed. After fitting new carbon brushes, properly retighten the brush

cap and mount the tail cover.

SERVICE AND REPAIRS

All quality power tools will eventually require servicing or replacement of parts because of

wear from normal use. To assure that only authorized replacement parts will be used, all

service and repairs must be performed by a HITACHI AUTHORIZED SERVICE CENTER,

ONLY.

NOTE:

Specifications are subject to change without any obligation on the part of the HITACHI.

Fig. 8

Wear limit

0.28” (7 mm)

No. of carbon

brush

0.67” (17 mm)

Français

INFORMATIONS IMPORTANTES

Lire et comprendre toutes les instructions de fonctionnement, les précautions de sécurité et

les avertissements dans ce mode d’emploi avant d’utiliser ou d’entretenir cet outil motorisé.

La plupart des accidents causés lors de l’utilisation ou de l’entretien de l’outil motorisé

proviennent d’un non respect des règles ou précautions de base de sécurité. Un accident

peut la plupart du temps être évité si l’on reconnaît une situation de danger potentiel avant

qu’elle ne se produise, et en observant les procédures de sécurité appropriées.

Les précautions de base de sécurité sont mises en évidence dans la section “SECURITE” de

ce mode d’emploi et dans les sections qui contiennent les instructions de fonctionnement

et d’entretien.

Les dangers qui doivent être évités pour prévenir des blessures corporelles ou un

endommagement de la machine sont identifiés par AVERTISSEMENTS sur l’outil motorisé

et dans ce mode d’emploi.

Ne jamais utiliser cet outil motorisé d’une manière qui n’est pas spécifiquement recommandée

par HITACHI sans avoir d’abord vérifié que l’utilisation prévue est sans danger pour vous et

les autres.

SIGNIFICATION DES MOTS D’AVERTISSEMENT

AVERTISSEMENT indique des situations potentiellement dangereuses qui, si elles sont

ignorées, pourraient entraîner de sérieuses blessures personnelles.

PRECAUTION indique des situations dangereuses qui, si elles sont ignorées, pourrait

entraîner de légères blessures personnelles ou endommager la machine.

REMARQUE met en relief des informations essentielles.

Français

SECURITE

CONSIGNES DE SECURITE IMPORTANTES POUR IIIII

L’UTILISATION DE TOUS LES OUTILS ELECTRIQUES

AVERTISSEMENT:Une utilisation incorrecte ou dangereuse des outils électriques

peut entraîner la mort ou des blessures graves.

LIRE TOUT CE MODE D’EMPLOI.

1. NE JAMAIS TOUCHER LES PARTIES MOBILES.

Ne jamais placer ses mains, ses doigts ou toute autre partie de son corps près des parties

mobiles de l’outil.

2. NE JAMAIS UTILISER L’OUTIL SANS QUE TOUS LES DISPOSITIFS DE SECURITE NE

SOIENT EN PLACE.

Ne jamais faire fonctionner cet outil sans que tous les dispositifs et caractéristiques de

sécurité ne soient en place et en état de fonctionnement. Si un entretien ou une réparation

nécessite le retrait d’un dispositif ou d’une caractéristique de sécurité, s’assurer de bien

remettre en place le dispositif ou la caractéristique de sécurité avant de recommencer à

utiliser l’outil.

3. TOUJOURS SE PROTEGER LES YEUX ET LES OREILLES.

Pour se protéger des projections de copeaux de bois, particules métalliques ou autres

débris, porter des lunettes de protection ou un masque pour les yeux. Porter des

protections anti-bruit pour se protéger du bruit.

4. SE PROTEGER CONTRE LES DECHARGES ELECTRIQUES.

Empêcher tout contact du corps avec les surfaces mises à la terre, par exemple tuyaux,

radiateurs, plaques de cuisson et enceintes de réfrigération. Ne jamais faire fonctionner

l’outil dans un endroit humide ou mouillé.

5. DEBRANCHER LES OUTILS.

Ne jamais laisser l’outil branché dans une source d’alimentation. Toujours débrancher

l’outil de la source d’alimentation avant tout travail de réparation, d’inspection, d’entretien,

de nettoyage, de remplacement ou de vérification des pièces.

6. EVITER TOUTE MISE EN MARCHE INOPINEE.

Ne pas transporter l’outil pendant qu’il est raccordé à la source d’alimentation. Ne pas

transporter l’outil avec le doigt près de l’interrupteur d’alimentation. Bien s’assurer que

l’interrupteur d’alimentation se trouve sur la position “OFF” (arrêt) avant de raccorder

l’outil à la source d’alimentation.

7. REMISER L’OUTIL CORRECTEMENT.

Lorsqu’on ne se sert pas de l’outil, le remiser dans un endroit sec. Veiller à ce qu’il soit

hors d’atteinte des enfants. Fermer le local de remisage à clé.

8. MAINTENIR L’AIRE DE TRAVAIL PROPRE.

Les aires de travail et les établis encombrés favorisent les accidents. Débarrasser l’aire

de travail et les établis des outils inutiles, débris, meubles, etc.

Français

9. CONSIDERER L’ENVIRONNEMENT DE L’AIRE DE TRAVAIL.

Ne pas exposer les outils à la pluie. Ne pas les utiliser dans un endroit humide ou mouillé.

Veiller à ce que l’aire de travail soit bien éclairée et bien aérée.

Ne pas utiliser l’outil en présence de liquides ou de gaz inflammables.

Les outils projettent des étincelles pendant qu’ils fonctionnent. Ne jamais utiliser les

outils dans un lieu renfermant de la laque, de la peinture, du diluant, de l’essence, des gaz,

des produits adhésifs ni aucun autre matériau combustible ou explosif.

10.ELOIGNER LES ENFANTS.

Ne pas laisser les visiteurs toucher l’outil ou le cordon de rallonge.

Tous les visiteurs devront être suffisamment éloignés de l’aire de travail.

11.NE PAS FORCER L’OUTIL.

Il effectuera le travail le meilleur et avec la sécurité maximale au régime pour lequel il a

été conçu.

12.UTILISER L’OUTIL CORRECT

Ne pas forcer sur un petit outil ou accessoire pour faire le travail d’un outil de grande

puissance. Ne pas utiliser un outil pour un usage pour lequel il n’a pas été prévu: par

exemple, ne pas utiliser une scie circulaire pour couper des branches d’arbre ou des

bûches.

13.SE VETIR CORRECTEMENT.

Ne pas porter de vêtements lâches ni de bijoux. Ils pourraient se prendre dans les pièces

en mouvement. Il est recommandé de porter des gants en caoutchouc et des chaussures

anti-glissantes lors d’un travail à l’extérieur.

Porter un couvre-chef qui recouvre les cheveux longs.

14. PORTER UN MASQUE, UN MASQUE ANTI-POUSSIERE OU UN APPAREIL RESPIRATOIRE

SI LE TRAVAIL DOIT DEGAGER DE LA POUSSIERE.

Toutes les personnes présentes sur l’aire de travail devront également porter un masque,

un masque anti-poussière ou un appareil respiratoire.

15.NE PAS MALTRAITER LE CORDON.

Ne jamais transporter l’outil par le cordon ni tirer brusquement sur le cordon pour le

débrancher.

Eloigner le cordon de la chaleur, de la graisse et des surfaces tranchantes.

16.FIXER LA PIECE.

Utiliser des dispositifs de serrage ou un étau pour tenir la pièce. Cela sera plus sûr que

de tenir la pièce à la main et libérera les deux mains pour le travail.

17.NE PAS TROP SE PENCHER.

Garder une bonne assise et un bon équilibre à tout moment.

18.ENTRETENIR LES OUTILS AVEC SOIN.

Maintenir les outils aiguisés et propres pour optimiser le travail et la sécurité.

Suivre les instructions de graissage et de remplacement des accessoires.

Vérifier périodiquement les cordons d’outil et les faire réparer par un centre de réparation

agréé s’ils sont endommagés. Vérifier périodiquement les cordons de rallonge et les faire

remplacer s’ils sont endommagés. Maintenir les poignées sèches et propres, et enlever

toute graisse et toute huile dessus.

19.RETIRER LES CLAVETTES DE REGLAGE ET LES CLES.

Les clés et les clavettes de réglage devront être retirées de l’outil avant de sa mise en

marche.

Français

20.CORDONS DE RALLONGE POUR UTILISATION A L’EXTERIEUR.

Si l’outil doit être utilisé dehors, utiliser exclusivement des cordons de rallonge conçus

pour un usage extérieur et marqués à cet effet.

21.RESTER SUR SES GARDES.

Bien faire attention à ce que l’on fait. Faire preuve de bon sens. Ne pas utiliser l’outil

lorsqu’on est fatigué.

Ne jamais utiliser l’outil si l’on est sous l’influence d’alcool, de drogues ou de médicaments

qui rendent somnolent.

22.VERIFIER S’IL Y A DES PIECES ENDOMMAGEES.

Avant de continuer à utiliser l’outil, inspecter attentivement les protections ou autres

pièces endommagées pour voir si l’outil pourra fonctionner correctement et effectuer le

travail pour lequel il est conçu. Vérifier l’alignement et le couplage des pièces mobiles,

le voilage des pièces mobiles, la présence de pièces cassées, le montage, et toute autre

condition susceptible d’affecter le bon fonctionnement.

Si une protection ou une pièce est endommagée, la faire réparer ou remplacer par un

service après-vente agréé, sauf spécification contraire dans ce mode d’emploi.

Faire remplacer les interrupteurs défectueux par un centre de réparation agréé.

Ne pas utiliser l’outil si l’interrupteur ne fonctionne pas.

23.NE JAMAIS UTILISER UN OUTIL MOTORISE POUR DES APPLICATIONS AUTRES QUE

CELLES SPECIFIEES.

Ne jamais utiliser un outil motorisé pour des applications autres que celles spécifiées

dans le mode d’emploi.

24.MANIPULER L’OUTIL CORRECTEMENT

Utiliser l’outil de la façon indiquée dans ce mode d’emploi. Ne pas laisser tomber ou

lancer l’outil. Ne jamais permettre que l’outil soit utilisé par des enfants, des personnes

non familiarisées avec son fonctionnement ou un personnel non autorisé.

25.VERIFIER S’IL Y A DES FILS SOUS TENSION.

Pour éviter tout risque de choc électrique grave, vérifier s’il y a des fils électriques sous

tension encastrés dans le mur, le plancher ou le plafond. Couper l’alimentation des fils

avant le travail.

26.MAINTENIR TOUTES LES VIS, TOUS LES BOULONS ET LES COUVERCLES FERMEMENT

EN PLACE.

Maintenir toutes les vis, tous les boulons et les couvercles fermement montés. Vérifier

leurs conditions périodiquement.

27.NE PAS UTILISER LES OUTILS MOTORISES SI LE REVETEMENT DE PLASTIQUE OU LA

POIGNEE EST FENDU.

Des fentes dans le revêtement ou la poignée peuvent entraîner une électrocution. De tels

outils ne doivent pas être utilisés avant d’être réparé.

28.LES LAMES ET LES ACCESSOIRES DOIVENT ETRE FERMEMENT MONTES

SUR L’OUTIL.

Eviter les blessures potentielles personnelles et aux autres. Les lames, les instruments

de coupe et les accessoires qui ont été montés sur l’outil doivent être fixés et serrés

fermement.

29.GARDER PROPRES LES EVENTS D’AIR DU MOTEUR

Les évents d’air du moteur doivent être maintenus propres de façon que l’air puisse

circuler librement tout le temps. Vérifier les accumulations de poussière fréquemment.

La page charge ...

Hitachi H 30PV Safety Instructions And Instruction Manual

Marque: Hitachi

Modèle: H 30PV

Taper: Safety Instructions And Instruction Manual

Ce manuel convient également à

H 45MA

Télécharger le PDF

rapport

dans d''autres langues

English: Hitachi H 30PV
español: Hitachi H 30PV

Hitachi H 30PV Safety Instructions And Instruction Manual

Ce manuel convient également à

Hitachi H 30PV Safety Instructions And Instruction Manual

dans d''autres langues

Documents connexes