Real Flame 590LP Le manuel du propriétaire

LOT#__________

PO#___________

CARBON MONOXIDE HAZARD

This appliance can produce carbon monoxide which has no odor.

Using it in an enclosed space can kill you.

Never use this appliance in an enclosed space such as a camper,

tent, car or home.

DANGER!

FIRE OR EXPLOSION HAZARD

If you smell gas:

• Extinguish any open ﬂame.

• If odor continues, leave the area

immediately.

• After leaving the area, call your

gas supplier or ﬁre department.

Failure to follow these instructions

could result in ﬁre or explosion,

which could cause property damage,

personal injury, or death.

!

DANGER

!

WARNING: FOR OUTDOOR USE ON LY.

Installation and service must be performed by a

qualiﬁed installer, service agency, or the gas supplier.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

!

WARNING: If the information in this manual is

not followed exactly, a ﬁre or explosion may result

causing property damage, serious injury, or loss of life.

!

WARNING: Do not store or use gasoline or other

ﬂammable vapors and liquids in the vicinity of this

or any other appliance.

An LP gas tank not connected for use shall not be

stored in the vicinity of this or any other appliance.

590LP Riverside Oval

Owner’s Manual

TABLE OF CONTENTS

Important Safety Information 3

Propane (LP) Gas Dangers and Warnings 5

Parts List 6

Assembly Instructions 7

Pre-Use Instructions 9

Lighting Instructions 10

Care and Cleaning 1 1

Spider and Insect Warning 12

Tips and Troubleshooting 13

Technical Parts List 15

Warranty and Return Policies 16

SPECIFICATIONS

Product Name

Model No.

590LP

Rated Heat Output

50,000 BTUs/hr

Type of Gas

Propane (LP)

Gas Supply

20 lb LP Gas Tank

2

ATTENTION

Please register your ﬁreplace for recall notiﬁcations, proof of ownership

and quality assurance at https://www.realﬂame.com/registration.

Riverside Oval

IMPORTANT SAFETY INFORMATION

General Warnings

• Children and adults should be alerted to the hazards of high surface temperatures

and should stay away to avoid burns or clothing ignition.

• Children should be carefully supervised when in the area of the ﬁreplace.

• Clothing or other ﬂammable materials should not be hung from the ﬁreplace or placed

on or near the ﬁreplace.

• Any guard or other protective device removed for servicing the ﬁreplace must be

replaced prior to operating the ﬁreplace.

• Installation and service must be performed by a qualiﬁed service agency or gas

supplier. Real Flame recommends using professionals who are certiﬁed in the U.S.

by the National Fireplace Institute® (NFI) as NFI Gas Specialists.

• More frequent cleaning may be required as necessary. It is imperative that the

control compartment, burners, and circulating air passageways of the appliance

are kept clean.

• Do not store or use gasoline or other ﬂammable vapors or liquids within 25 feet (7.62 m)

of this ﬁreplace or any other appliance.

• Do not store combustible materials in the ﬁreplace enclosure. This includes LP gas tanks.

If the ﬁreplace is designed to use a hidden LP gas tank, the LP gas tank should be

properly secured in the designated tank holder under the ﬁreplace. Do not store extra

LP gas tanks under the ﬁreplace.

• Be sure to protect the hose and its components from any hot surfaces. It is dangerous

to allow the hose to come into contact with any hot surface.

• The LP gas tank should never be operated or stored on its side or upside down.

• Keep all parts of the ﬁreplace clean including the burner and hose assembly. For more

information on cleaning your ﬁreplace please refer to the “Care and Cleaning” section

of this manual.

• Do not use this ﬁreplace if any part has been under water. Immediately call a qualiﬁed

service technician to inspect the ﬁreplace and replace any part of the system that has

been under water.

• Do not use this ﬁreplace for cooking.

• Do not pour water into the ﬁreplace.

• Do not attempt to move or store this ﬁreplace until all parts are cool.

• Always shut o the gas supply at the source and disconnect the hose when the ﬁreplace

is not in use.

• Any alteration of this ﬁreplace that is not speciﬁcally directed in the owner’s manual

will void the manufacturer’s warranty. This includes the use of unapproved ﬁller materials.

3

Installation Warnings

• The normal LP inlet pressure for this ﬁreplace is 11.0” W.C. (2.74 kPa). Maximum inlet pressure

is 13.0” W.C. (3.23 kPa). Minimum inlet pressure is 8” W.C. (1.99 kPa).

• Do not remove the feet from this ﬁreplace.

• Do not place the ﬁreplace on anything that blocks or seals the gap between the ﬁreplace and the ground.

• Do not permanently secure the ﬁreplace in any way or to any surfaces.

• Do not bury the hose. You must be able to visually inspect the hose for damage before each use.

• Do not coil or hide the hose under the ﬁreplace. The hose could be damaged if it touches hot surfaces.

Set Up Warnings

• Prior to each operation, check the hose assembly for evidence of excessive abrasion, wear or

damage. Use a handheld mirror, if necessary, to see the hose sections located below the unit.

• If the hose assembly is damaged, cracked, or cut, it must be replaced before using the ﬁreplace.

The hose assembly must be replaced with a hose assembly speciﬁed by Real Flame.

Please contact Real Flame Customer Service at 1-800-654-1704 for assistance.

• Place the hose out of the pathways where people may trip

over it. Do not place the hose

in areas where it may be accidentally damaged.

• Before each use, examine the burner and its components for dirt and debris. If cleaning is required,

use a pipe cleaning brush and compressed air. Also examine the area around the burner.

Any dirt or foreign material, such as spider webs, nests, leaves, etc., should be removed. If it is

evident that the burner is damaged, the ﬁreplace must not be used, and the burner assembly

must be replaced. Please contact Real Flame Customer Service at 1-800-654-1704 for support.

In-Use Warnings

• NEVER LEAVE this ﬁreplace unattended when in use.

• Do not burn solid fuels, such as charcoal briquettes, lump charcoal, manufactured logs, trash, leaves

paper, cardboard, any type of natural or treated wood, or any other materials in this ﬁreplace.

• The use of alcohol, prescription or non-prescription drugs may impair your ability to safely

operate this ﬁreplace.

• Always use in accordance with all applicable local, state, and national codes. Contact your

local ﬁre department for details on outdoor burning.

• Do not use in windy conditions. Windy conditions may cause the flame to drift out of the

designated burn area or may cause the flame to extinguish. Prolonged exposure to wind

with the fire table in operation can damage the finish around the burner area, causing

discoloration or cracking.

• Some surfaces of this ﬁreplace may become hot d

uring use. Be careful and do not touch

surfaces until the unit has cooled.

• Do not attempt to disconnect the gas supply from the ﬁreplace when the unit is in use.

• Do not sit on the ﬁreplace.

4

IMPORTANT SAFETY INFORMATION

• Minimum clearance from the ﬁreplace to combustible materials is 60 inches (152.4 cm) from

top and 48 inches (121.9 cm) on all sides. Do not place this ﬁreplace under any overhead

structure or vegetation.

PROPANE (LP) GAS DANGERS AND WARNINGS

!

WARNING

LP gas is ﬂammable and hazardous if handled improperly. Become aware of its characteristics before

using any LP gas product. Failure to understand and follow these warnings or any directions and

warnings provided by your LP gas supplier may result in property damage, serious injury, or death.

!

DANGER

An LP gas tank should never be placed on its side. Doing so may cause liquid propane to leak.

This could cause a fast buildup of LP gas and could lead to property damage, serious injury, or death.

LP Gas Characteristics

• LP gas is ﬂammable, explosive under pressure, heavier than air and settles in pools in low

areas. Pooled gas may ignite causing a ﬁre or explosion which could cause property

damage, serious injury, or death.

• In its natural state, LP gas has no odor. For your safety, a scent has been added.

• Contact with LP gas could burn your skin.

LP Gas Tank Information

• LP gas tanks should be ﬁlled only by a certiﬁed LP gas dealer.

• Never use an LP gas tank with a damaged body, valve, collar or footing.

• Dented or rusted LP tanks may be hazardous and should be checked by your LP gas supplier.

• The LP gas supply tank must be constructed and marked in accordance with The Speciﬁcations

for LP Gas Tanks of The U.S. Department of Transportation (DOT) or The National Standard

of Canada, CAN/CSA-B339, LP Gas Tanks, Spheres and Tubes for The Transportation of

Dangerous Goods; and Commission.

• LP gas tanks must be arranged for vapor withdrawal.

• LP gas tanks must have a listed overﬁlling prevention device (OPD) and a QCCI or Type I

(CGA810) LP gas tank connection.

• The LP gas tank must contain a shut-o valve as speciﬁed in The Standard for

Compressed Gas Cylinder Valve Outlet and Inlet Connection, ANSI/CGA-V-1-1977, CSA B96.

• Never attempt to attach this ﬁreplace to the self-contained LP gas system of a camper,

trailer, motor home or house.

• Hand-turn the manual gas control valve on your LP gas tank. Never use tools. If the valve

will not turn by hand, do not try to repair it. Call a certiﬁed gas technician.

• The use of force or any attempt at amateur repair may cause a ﬁre or explosion.

LP Gas Tank Storage and Safety

• LP gas tanks must be stored upright and outdoors in a well-ventilated area out of reach of children.

• Never store an LP gas tank in an enclosed area, such as a shed or garage. Leaking gas could build

up in these areas and may result in an explosion.

• Do not store LP gas tanks near any source of ﬂame or ignition.

• Never store an LP gas tank in direct sunlight or where temperatures can reach 125°F (51.67°C) or higher.

• Never keep a ﬁlled LP gas tank in a hot car or car trunk. Heat will cause the gas pressure to

increase, which may open the relief valve and allow gas to escape.

• Place the dust cap on the LP gas tank valve outlet when the LP gas is not in use. Only use

the dust cap that is provided with the LP gas tank. Other types of caps or plugs may

result in leakage of LP gas.

• The LP gas tank should not be dropped or handled roughly.

5

PARTS LIST

6

1

3

4

5

2

Protective cover

05900001

Fire Table

N/A

Tank Seat

05600005

Pumice Stone

100043000

0562LP10

1

2

3

1

2

1

5

4

LP Hose and regulator

6

AAA Battery

N/A

1

6

AAA

ASSEMBLY INSTRUCTIONS

Install the AAA battery as shown in the diagram below.1 .

Place the ﬁller material into the burner pan by hand. To avoid clogging the burner with dust

do not dump the bag into the burner pan. Position the ﬁller across the burner pan to a level

that is 1 inch (2.54 cm) above the burner tube. Make sure you do not block the igniter housing

with the ﬁller material to ensure proper ignition and operation.

If using glass ﬁller, Real Flame suggests ﬁrst placing a layer of lava rock in the burner pan

to improve airﬂow.

Filler Material Warning

• Do not overﬁll the burner area with rock or glas

s ﬁller; use only the speciﬁed amount. The

depth of the ﬁller should not be more than 1 inch (2.54 cm) above the burner tube. Only

Real Flame ﬁller products have been certiﬁed and tested for safe use with this Real Flame

ﬁreplace. Using other ﬁller material may result in increased popping and cracking or increased

carbon monoxide emissions.

• Do not light or use this ﬁreplace if the ﬁller is wet

. Ensure ﬁller is completely dry before lighting.

Intense heat can cause wet ﬁller to explode and hit someone causing property damage,

serious injury, or death.

• Keep away from the ﬁreplace for at least 20 minutes during initial start-up as ﬁller could

retain moisture from manufacturing and shipping.

7

2.

Igniter housing

ASSEMBLY INSTRUCTIONS

3. Place the tank seat on the ground and place a 20 lb LP gas tank into the designated area

in the center. Once the tank is level and steady, tighten down the screw on the side of the

tank seat to secure the tank in place.

4. Connect the LP Gas Tank

Before connection, be sure there is no debris caught in the

collar of the LP gas tank, the regulator valve, the burner

tube, or the burner ports.

Connect the gas line to the tank by turning the connection

knob clockwise. Hand-tighten only.

Disconnect the LP Gas Tank

To disconnect the LP gas tank, make sure the valve on the

LP gas tank is completely closed.

Disconnect the connection knob by turning it counterclockwise

until it is detached from the valve.

!

WARNING

Place the LP gas tank 60 inches (152.4 cm) away from the

ﬁreplace and position the hose away from pathways or

places where it could become damaged.

Watch your step while moving between the tank and the

ﬁreplace. Be careful not to trip on the hose.

8

60”

PRE-USE INSTRUCTIONS

!

WARNING

Before using this ﬁreplace, make sure you have read, understand, and are following all information

provided in this manual. Failure to follow these instructions could cause property damage,

serious injury, or death.

Checking for Leaks

1. Make a leak check solution by mixing 1 part dishwashing soap with 3 parts water in a spray bottle.

2. Make sure the control knob on the ﬁreplace is in the “OFF” position, then connect your

ﬁreplace to the LP gas tank and turn the tank’s valve on.

3. Spray the leak solution on the valve connections, paying particular attention to the areas

indicated by arrows in the diagrams below.

4. If bubbles appear, turn the LP gas tank o, disconnect the tank, and inspect all connections,

making sure threads are clear of debris. Reconnect the LP gas tank and retest. If you continue

to see bubbles, turn the LP gas tank o. Disconnect the hose and call Real Flame Customer

Service at 1-800-654-1704 for assistance.

5. If no bubbles appear after 1 minute, wipe away excess leak solution and proceed to

“Lighting Instructions.”

9

Pay close attention to the areas indicated by the arrows.

LIGHTING INSTRUCTIONS

Using the Igniter

1. Read and understand all operating instructions before lighting.

2. Before beginning, make sure the control knob is in the “OFF” position.

3. Connect your LP gas tank (see previous pages).

4. Slowly open the valve on your LP gas tank.

5. Prepare to ignite your ﬁreplace by placing one hand on the control

knob and one hand on the igniter button (see diagram). DO NOT

lean over any part of the burner. Verify that the area around the

burner is free of hazards.

6. Push and hold the igniter button. You should hear a clicking sound.

7. While keeping the ignition button depressed, use your other hand to push in and turn the

control knob counterclockwise to the “LIGHT” position.

8. Once the burner ignites, release the igniter button, but continue to keep the control knob

pushed in for 15-30 seconds.

WARNING: If ignition does not occur in 15 seconds, turn the control knob to the “OFF”

the ﬁreplace and wait at least 5 minutes until the gas has cleared to repeat the lighting

procedure. Failure to do so could result in a large ﬂashback of pooled gas, causing property

damage, serious injury, or death.

9. After successfully lighting the ﬁreplace, release the control knob and turn it to the “LOW” setting.

Observe the ﬂame and make sure that all the burner ports are lit.

10. Adjust the ﬂame to the desired height using the control knob.

Control Knob

Flame Height

8-14”

(20.3-35.5 cm)

10

1. Push and turn the control knob clockwise to the “OFF” position.

Turn the gas o at its source (LP tank or shut o valve).

2.

CARE AND CLEANING

Inspecting Your Fireplace

!

WARNING

DO NOT inspect, clean, move or store your ﬁreplace until the ﬂames are COMPLETELY out

and all parts are cool to the touch.

Your ﬁreplace should be inspected regularly to ensure that it is safe to use and to extend the life of its parts.

To inspect your ﬁreplace follow these steps:

1. Make sure all parts are securely fastened in place. If a part moves when touched, check its

connection points to see if they are loose.

2. Check all connections for leaks using the method described in the “Checking for Leaks” section

of this manual.

3. Check the igniter system by pushing the igniter button and verifying that a spark is being

generated in the igniter housing.

4. Visually check all components for any signs of damage, rust, or excessive wear.

5. If damage or leaks of any kind are found. DO NOT operate the ﬁreplace until the proper

repairs have been made.

!

WARNING

DO NOT tamper with this ﬁreplace. This is dangerous and will void the warranty.

Repairs and modiﬁcations must be approved by Real Flame and completed by a

professional gas technician.

This ﬁreplace has been tested and certiﬁed by a third party certiﬁcation agency based on its

speciﬁc and unique parts. Installing any other parts will void both the certiﬁcation and the warranty.

For approved replacement parts contact Real Flame Customer Service at 1-800-654-1704.

General Care and Cleaning

After repeated use, a slight discoloration or weathering of the ﬁreplace ﬁnish may occur. Your

ﬁreplace should be cleaned regularly to ensure safe use and extend its life.

General Cleaning

Make a cleaning solution using a mild soap mixed with water. Use a soft cloth to wipe down

exterior surfaces and rinse with clean water. Never use oven cleaners or abrasive solvents as

these will damage the ﬁreplace.

Burner

The burner should be kept clean to ensure proper operation. Clogged burner ports may be

cleared with a paper clip or pin. Debris in the burner tube can be cleaned using compressed

air or a pipe cleaning brush.

Soot

After use it is possible for soot to develop on some surfaces. This soot deposit will usually

come o with water and mild soap.

Storage

1. Turn the LP gas supply o at the tank. Remove the LP gas tank and store it in a cool, dry

location, outside and away from children.

2. Secure all loose ﬁller material or parts.

3. Remove the battery from the igniter box.

4. Cover the ﬁreplace when not in use and do not allow water to pool on the cover surface.

Covering the ﬁreplace will help to protect the internal components from dirt and debris

and prevent the ﬁnish from fading.

5. Store the ﬁreplace in a cool, dry location away from children and pets.

11

SPIDER AND INSECT WARNING

Spiders or other insects may build webs or nests in your ﬁreplace burner tube which can obstruct

or block the ﬂow of gas.

Some of the gas may back up in the burner tube and cause a ﬂashback (a ﬁre in the burner tube

or underneath the ﬁreplace), which could result in property damage, serious injury, or death.

Check and clean the burner tube periodically using a pipe cleaning brush (shown below) and

compressed air available at any hardware store.

Example of a typical burner tube.

Your exact burner may vary.

Burner Tube

Air Intake

Run pipe cleaning brush

through burner tube.

Possible Debris

Example of pipe cleaning

brush available at local

hardware store.

12

13

TIPS AND TROUBLESHOOTING

If the Fireplace Will Not Ignite

Thermocouple

Make sure ﬂame

is contacting this.

Igniter Pin

You should see this

spark when pushing

the igniter button.

Igniter Housing

removed for visibility.

+

-

If the igniter system is working correctly, you should hear a clicking

sound while the igniter button is being pushed and you should see a

spark inside the igniter housing. If you do not see the spark or hear

a clicking sound, please check the following:

1. Make sure the battery is not dead and that it is installed correctly,

with the positive (+) side facing out.

2. If you still do not hear a clicking sound or see a spark in the igniter

box, look under the ﬁreplace and make sure that the electrode

wire is corr

ectly inserted into the back of the electronic igniter box.

While inspecting the electrode wire, make sure that it is not cut or

broken in any place. If the wire has been damaged contact Real Flame

Customer Service at 1-800-654-1704 for a replacement.

If the Fireplace Will Not Stay Lit

If the ﬁreplace lights, but will not stay lit, or remains lit only for a brief time, please check the following:

1. Make sure that the igniter housing is unobstructed. Clear away any ﬁller material or debris on the

housing and make sure there is nothing between the igniter pin and the thermocouple.

DO NOT block

opening

Igniter Housing

Burner Tube

Igniter Pin

Thermocouple

Back of

Electronic

Ignition

14

TIPS AND TROUBLESHOOTING

If the Fireplace Will Not Stay Lit (Cont.)

2. Make sure the thermocouple and igniter pin

are correctly positioned.

Thermocouple - The thermocouple tip should be

located close to the burner, aligned with a

burner port so that ﬂames contact it directly.

Make sure the ﬂames are making contact with

the thermocouple tip.

Damaged Thermocouple

If the igniter housing and the thermocouple tip are clear of debris and the ﬂame is clearly

contacting the tip of the thermocouple, but the ﬁreplace will still not stay lit, the thermocouple

may be dama

ged. Look beneath the ﬁreplace and ﬁnd the copper thermocouple wire coming

out of the back of the valve. Examine the length of it for any signs of damage. Sharp bends,

kinks or damage can cause the thermocouple to not function correctly. If you ﬁnd damage

to the thermocouple contact Real Flame Customer Service at 1-800-654-1704 for a replacement.

Igniter Pin - The igniter pin is where the spark is generated to ignite your ﬁreplace. Make

sure you can see this sparking when the igniter button is pushed. If you do not see a s

park

please contact Real Flame Customer Service at 1-800-654-1704.

Other Common Problems

Clogged or Obstructed Burner

It is common for bugs, especially spiders, to make webs or nests inside of burner tubes.

If it seems like you are getting low or no gas ﬂow, visually check all openings in the burner

for signs of clogs. If you see anything clogging the burner try using a pipe cleaning brush

and compressed air to remove the debris.

Out of Gas

Be sure your LP gas tank is not empty. Low tanks can result in lower ﬂames.

Cold Temperatures

Cold temperatures outside may result in lower LP gas tank pressures causing the ﬂa

mes

to be lower. Do not use your ﬁreplace in extreme temperature conditions. Allow the

temperature of your LP gas tank to rise and as the pressure in the LP gas tank increases

the ﬂame size will increase. NEVER heat your LP gas tank; allow it to warm up naturally.

High Winds

Your ﬁreplace is designed to operate in winds up to 10 mph (16.09 kph). High winds may

cause the ﬂame to blow out. Do not operate your ﬁreplace in high wind conditions.

If you continue to have problems with your ﬁreplace please

contact Real Flame Customer Service at 1-800-654-1704.

Igniter

Housing

Burner

Tube

Igniter Pin

Thermocouple

TECHNICAL PARTS LIST

15

Flex Line (CSST)

100230005

LP Oriﬁce Spud 2.14mm

100270019

Valve

100130002

Control Knob

10040U000

Thermocouple

100300005

Igniter Electrode

and Ground

100280029

Electronic Ignition

100240000

Igniter Button

05600013

Tank Seat

05600005

Protective cover

05900001

100390010

Pumice Stone

100043000

LP Hose and Regulator

0562LP10

Burner Tube

Body

N/A

Igniter Housing

100280000

16

WARRANTY

Limited Warranty

Real Flame® warrants that the following components of this Real Flame® ﬁreplace ("the Product")

will be free from manufacturing defects in material and workmanship after correct assembly and

under normal use and proper maintenance for the periods indicated below, commencing with the

date of purchase of the Product:

• The body – 1 year limited warranty.

• The internal components – 1 year limited warranty.

• The burner system – 1 year limited warranty.

This non-transferable warranty extends to the original purchaser only, provided that the purchase

was made through an authorized Real Flame dealer. The warranty is also subject to the following

conditions and limitations:

This warranty does not extend to damages caused by shipping, improper assembly, installation or

storage, installation that does not comply with building codes and ordinances, installation or

operation not in accordance with the included manual, abuse, lack of maintenance, hostile

environments, accident, natural weather, or unworkmanlike repairs. Modiﬁcation of the Product,

use of fuels other than what is approved by Real Flame, or use of parts installed from other

manufactures will nullify this warranty.

This warranty applies to the functionality of the Product only and does not cover cosmetic issues

such as scratches, dents, rust, oxidation, corrosion, areas discolored or cracked due to prolonged

exposure to extreme heat, or damage caused by abrasive or chemical cleaners. However, should

deterioration of parts occur to the degree of non-performance within the duration of the warranty

period, Real Flame will provide a replacement part.

Real Flame requires reasonable proof of your date of purchase. Therefore, you should retain your

sales receipt and/or invoice. Defective parts subject to this warranty will not be replaced without

proof of purchase.

Real Flame must have the opportunity to verify the alleged defect. In order for any internal

components to be covered under warranty, Real Flame requires the user to troubleshoot with a Real

Flame Customer Service member to ensure proper operation and diagnosis of issue.

In the event of covered defects in warrantied items, Real Flame will, at its sole option and discretion,

replace the defective component, replace the Product or refund the purchase price. Real Flame is

not responsible for the installation, labor or any other costs associated with the reinstallation. The

foregoing is the exclusive remedy under the terms of this limited warranty. Real Flame will not be

responsible for any incidental or consequential damages caused by defects in the Product. Some

states do not allow the exclusion or limitation of incidental or consequential damages, so the above

limitation or exclusion may not apply to you.

This limited warranty is the sole express warranty given by Real Flame. The duration of any implied

warranty arising under the laws of any state, including implied warranty of merchantability or ﬁtness

for a particular purpose or use, is limited to the duration of the warranty speciﬁed above. Some

states do not allow limitations on how long an implied warranty lasts, so this limitation may not

apply to you.

This warranty gives you speciﬁc legal rights, and you may also have other rights which vary from

State to State.

For warranty service:

1. Call Real Flame Customer Service at 1-800-654-1704 for technical support and troubleshooting.

2. If experiencing issues with ﬁnish, please ﬁll out the ‘Outdoor Warranty Claim’ form at

www.realﬂame.com.

03022020

17

Real Flame®

7800 Northwestern Ave.

Racine, WI 53406

USA

Customer Service: 1-800-654-1704 in USA

Service à la clientèle: 1-800-363-6443 in Canada

custserv@realﬂame.com

Return Policy

You may return your purchase within 90 days of receipt. No refunds will be issued for incomplete

or unauthorized returns. All returned products must be 100% complete, adequately packaged in

original packaging and in resalable condition. Products that have been assembled or modiﬁed will not

be eligible for return. All items must be returned in their entirety, meaning all items included must be

returned together. No returns or exchanges on discontinued items. Please begin the return process by

contacting the store or company where you bought your Real Flame® item.

Replacement Parts

In the event that an item has been lost or damaged, either by the manufacturer or in shipping, you

may request a replacement. Replacement parts are not available for all units and only given at Real Flame’s

discretion. We will assess any damage and ﬁnd a solution, which could include shipping you a replacement.

No replacements are available for discontinued items or repackaged (open box) products. Please

call Real Flame Customer Service at 1-800-654-1704 for replacement parts before returning the damaged

item. Please have the following information (which can be found in your instruction manual) ready

before you call Customer Service:

• Model number of item

• 4-8 digit part number

• Lot code number

• Shipping address

• A picture of the damaged item may be requested. Pictures should be sent to custserv@realﬂame.com.

Incorrect Order Received

If you received something other than what you ordered, please contact Real Flame Customer Service at

1-800-654-1704 within 48 hours of receiving the item.

Refer to www.realﬂame.com for our complete return guidelines and policies.

Please register your ﬁreplace for recall notiﬁcations, proof of ownership and quality assurance at

https://www.realﬂame.com/registration.

RETURN POLICY

LOT#__________

PO#___________

RISQUE DE MONOXYDE DE CARBONE

Cet appareil peut produire du monoxyde de carbone qui n'a pas d'odeur.

Son utilisation dans un espace clos peut vous tuer.

Ne jamais utiliser cet appareil dans un espace clos tel qu'une caravane,

une tente, une voiture ou une maison.

DANGER!

!

DANGER

!

AVERTISSEMENT : USAGE EXTÉRIEUR UNIQUEMENT.

!

RISQUES D’INCENDIE ET D'EXPLOSION

En cas de présence d’odeur de gaz :

• Couper l'alimentation en gaz vers

l'appareil.

• Éteindre toute ﬂamme nue.

• Si l'odeur persiste, quitter immédi-

atement les lieux.

• Après avoir quitté les lieux, appeler

votre fournisseur de gaz ou le service

d'incendie. Si ces précautions ne sont

pas respectées, cela pourrait pro-

voquer un incendie ou une explosion,

pouvant causer des dommages

matériels, des blessures ou la mort.

-

teur qualiﬁé, un service d’entretien ou le fournisseur de gaz.

INSTALLATEUR : Laisser ce manuel avec l'appareil.

CONSOMMATEUR : Conserver ce manuel pour référence

future.

AVERTISSEMENT : Si les informations contenues dans

ce manuel ne sont pas suivies à la lettre, un incendie ou

une explosion pourrait survenir et entrainer des

dommages matériels, des blessures graves ou la mort.

AVERTISSEMENT : Ne pas entreposer et ne pas utiliser

d’essence ou d’autres liquides ou vapeurs inﬂammables à

proximité de cet appareil ou de tout autre appareil.

Un réservoir de GPL non raccordé pour être utilisé ne

doit pas être entreposé à proximité de cet appareil ou

de tout autre appareil.

590LP Riverside Oval

Manuel du propriétaire

TABLE DES MATIÈRES

Informations importantes sur la sécurité 3

Dangers et avertissements concernant le gaz propane (GPL) 5

Liste des pièces 6

Instructions d’assemblage 7

Instructions avant l’utilisation 9

Entretien et nettoyage 1 1

Avertissement concernant les araignées et les insectes 12

Conseils et dépannage 13

Liste des pièces techniques 15

Garantie et politiques de retour 16

SPÉCIFICATIONS

Nom du produit

N° de modèle

590LP

Puissance thermique

nominale

50,000 BTU/h

Type de gaz

Propane (GPL)

Approvisionnement en gaz

2

ATTENTION

Veuillez enregistrer votre foyer pour recevoir les notiﬁcations de

rappel, les preuves de propriété et l’assurance qualité à l’adresse

https://www.realﬂame.com/registration.

Bonbonne de GPL de 20 lb

Instructions d'allumage 10

Riverside Oval

La page charge ...

Real Flame 590LP Le manuel du propriétaire

Ce manuel convient également à

Real Flame 590LP Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents