Toro Super Recycler C53AST 53 cm Lawn Mower Manuel utilisateur

Form No. 3450-890 Rev D

53cm Super Recycler

®

Lawn Mower

21693

Super Recycler

®

Rasenmäher (53 cm)

21693

T ondeuse Super Recycler

®

de 53 cm

21693

53 cm Super Recycler

®

gazonmaaier

21693

www .T oro.com.

*3450-890*

Form No. 3450-878 Rev D

53cm Super Recycler

®

Lawn Mower

Model No. 21693 —Serial No. 400000000 and Up

Operator's Manual

Introduction

This rotary-blade, walk-behind lawn mower is intended

to be used by residential homeowners. It is designed

primarily for cutting grass on well-maintained lawns on

residential properties. Using this product for purposes

other than its intended use could prove dangerous to

you and bystanders.

Read this information carefully to learn how to operate

and maintain your product properly and to avoid

injury and product damage. Y ou are responsible for

operating the product properly and safely .

V isit www .T oro.com for more information, including

safety tips, training materials, accessory information,

help nding a dealer , or to register your product.

Whenever you need service, genuine T oro parts, or

additional information, contact an Authorized Service

Dealer or T oro Customer Service and have the model

and serial numbers of your product ready . Figure 1

identies the location of the model and serial numbers

on the product. W rite the numbers in the space

provided.

Important: W ith your mobile device, you can

scan the QR code on the serial number decal (if

equipped) to access warranty , parts, and other

product information

g374302

Figure 1

1. Model and serial number location

Model No.

Serial No.

Safety-Alert Symbol

The safety-alert symbol ( Figure 2 ) shown in this

manual and on the machine identies important safety

messages that you must follow to prevent accidents.

g000502

Figure 2

Safety-alert symbol

The safety-alert symbol appears above information

that alerts you to unsafe actions or situations and

is followed by the word DANGER ,W ARNING , or

CAUTION .

DANGER indicates an imminently hazardous situation

which, if not avoided, will result in death or serious

injury .

W ARNING indicates a potentially hazardous situation

which, if not avoided, could result in death or serious

injury .

CAUTION indicates a potentially hazardous situation

which, if not avoided, may result in minor or moderate

injury .

This manual uses two other words to highlight

information. Important calls attention to special

mechanical information and Note emphasizes general

information worthy of special attention.

This product complies with all relevant European

directives; for details, please see the separate product

specic Declaration of Conformity (DOC) sheet.

Gross or Net T orque: The gross or net torque

of this engine was laboratory rated by the engine

manufacturer in accordance with the Society of

Automotive Engineers (SAE) J1940 or J2723. As

congured to meet safety , emission, and operating

requirements, the actual engine torque on this class

of mower will be signicantly lower . Please refer to

the engine manufacturer ’ s information included with

the machine.

Do not tamper with or disable safety devices on the

machine, and check their proper operation regularly .

Do not attempt to adjust or tamper with the engine

81 1 1 L yndale A venue South

Bloomington, MN 55420

Register at www .T oro.com.

Original Instructions (EN)

Printed in Mexico

*3450-878*

speed control; doing so may create an unsafe

operating condition, resulting in personal injury .

Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Safety-Alert Symbol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Safety ....................................................................... 3

General Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Safety and Instructional Decals . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Setup ........................................................................ 5

1 Assembling and Unfolding the Handle . . . . . . . . . . . . . . 5

2 Installing the Blade-Control Bar . . . . . . . . . . . . . . . . . . . . . . . . 5

3 Installing the Recoil-Starter Rope in the

Rope Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

4 Adding Oil to the Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

5 Assembling the Grass Bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Attachments/Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Before Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Before Operation Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Filling the Fuel T ank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Checking the Engine-Oil Level . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1

Adjusting the Handle Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Adjusting the Cutting Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

During Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

During Operation Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Starting the Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Using the Self-Propel Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Shutting Of f the Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Recycling the Clippings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Bagging the Clippings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Operating T ips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

After Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

After Operation Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Cleaning Under the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Folding the Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Storing the Machine in the V ertical-Stow

Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Recommended Maintenance Schedule(s) . . . . . . . . . . . 21

Maintenance Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Preparing for Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Servicing the Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Changing the Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Replacing the Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Adjusting the Self-Propel Drive . . . . . . . . . . . . . . . . . . . . . . . . . 24

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Storage Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Preparing the Machine for Storage . . . . . . . . . . . . . . . . . . . 25

Removing the Machine from Storage . . . . . . . . . . . . . . . . 25

2

Safety

General Safety

This product is capable of amputating hands and

feet and of throwing objects. Always follow all safety

instructions to avoid serious personal injury or death.

•Read, understand, and follow the instructions

and warnings in this Operator ’ s Manual and on

the machine and attachments before starting the

engine.

•Do not put your hands or feet near moving parts or

under the machine. Keep clear of any discharge

opening.

•Do not operate the machine without all guards

and other safety protective devices in place and

functioning properly on the machine.

•Keep bystanders and children out of the operating

area. Do not allow children to operate the machine.

Allow only people who are responsible, trained,

familiar with the instructions, and physically

capable to operate the machine.

•Stop the machine, shut of f the engine, and wait for

all moving parts to stop before servicing, fueling,

or unclogging the machine.

Improperly using or maintaining this machine can

result in injury . T o reduce the potential for injury ,

comply with these safety instructions and always

pay attention to the safety-alert symbol , which

means Caution, W arning, or Danger—personal safety

instruction. Failure to comply with these instructions

may result in personal injury or death.

Safety and Instructional

Decals

Safety decals and instructions are

easily visible to the operator and are

located near any area of potential

danger . Replace any decal that is

damaged or missing.

decaloemmarkt

Manufacturer's Mark

1. This mark indicates that the blade is identied as a part

from the original machine manufacturer .

decal1 12-8760

1 12-8760

1. Thrown object hazard—keep bystanders away .

2. Cutting/dismemberment hazard of hand or foot, mower

blade—stay away from moving parts.

3

decal131-4514

131-4514

1. W arning—read the Operator's Manual .

2. Cutting/dismemberment hazard of hand, mower

blade—stay away from moving parts; keep all guards and

shields in place.

3. Cutting/dismemberment hazard of hand, mower

blade—disconnect the spark-plug wire before performing

maintenance.

4. Thrown object hazard—keep bystanders away; shut of f the

engine before leaving the operating position; pick up any

debris before mowing.

5. Cutting/dismemberment hazard of foot, mower blade—do

not operate up and down slopes; operate side to side on

slopes; look behind you when moving in reverse.

decal133-8198

133-8198

1. W arning—read the Operator's Manual ; add fuel up to the

indicated level, then tip the machine onto the rear wheels

for storage.

4

Setup

Important: Remove and discard the protective plastic sheet that covers the engine and any other

plastic or wrapping on the machine.

1

Assembling and Unfolding the Handle

No Parts Required

Procedure

W ARNING

Assembling and unfolding the handle improperly can damage the cables, causing an unsafe

operating condition.

• Do not damage the cables when assembling and unfolding the handle.

• Ensure that the cables are routed to the outside of the handle.

• If a cable is damaged, contact an Authorized Service Dealer .

g367755

Figure 3

5

2

Installing the Blade-Control Bar

No Parts Required

Procedure

g344378

Figure 4

3

Installing the Recoil-Starter

Rope in the Rope Guide

No Parts Required

Procedure

Important: T o start the engine safely and easily whenever you use the machine, install the recoil-starter

rope in the rope guide.

g334093

Figure 5

6

4

Adding Oil to the Engine

No Parts Required

Procedure

Important: If the oil level in the engine is too low or too high and you run the engine, you may damage

the engine.

g222533

Figure 6

7

5

Assembling the Grass Bag

No Parts Required

Procedure

g334351

Figure 7

8

Product Overview

g367232

Figure 8

1. Handle

7. Cutting-height lever (4)

2. Blade-control bar

8. Spark plug

3. Adjustment for the

self-propel drive

9. Oil ll/dipstick

4. Rear deector 10. Handle knob (2)

5. Fuel-tank cap

1 1. Grass bag

6. Air lter

12. Recoil-start handle

Specications

Model W eight Length W idth Height

38 kg21693

(84 lb)

164 cm 58 cm 106 cm

Attachments/Accessories

A selection of T oro approved attachments and

accessories is available for use with the machine

to enhance and expand its capabilities. Contact

your Authorized Service Dealer or authorized T oro

distributor or go to www .T oro.com for a list of all

approved attachments and accessories.

T o ensure optimum performance and continued safety

certication of the machine, use only genuine T oro

replacement parts and accessories. Replacement

parts and accessories made by other manufacturers

could be dangerous, and such use could void the

product warranty .

9

Operation

Note: Determine the left and right sides of the

machine from the normal operating position.

Before Operation

Before Operation Safety

General Safety

•Always shut of f the machine, wait for all moving

parts to stop, and allow the machine to cool before

adjusting, servicing, cleaning, or storing it.

•Become familiar with the safe operation of the

equipment, operator controls, and safety signs.

•Check that all guards and safety devices, such as

deectors and/or grass catcher , are in place and

functioning properly .

•Always inspect the machine to ensure that the

blades and blade bolts are not worn or damaged.

•Inspect the area where you will use the machine,

and remove all objects that could interfere with

the operation of the machine or that the machine

could throw .

•Contact with the moving blade will cause serious

injury . Do not put your ngers under the housing.

Fuel Safety

•Fuel is extremely ammable and highly explosive.

A re or explosion from fuel can burn you and

others and can damage property .

– T o prevent a static charge from igniting the fuel,

place the container and/or machine directly on

the ground before lling, not in a vehicle or on

an object.

– Fill the fuel tank outdoors, in an open area,

when the engine is cold. Wipe up any fuel that

spills.

– Do not handle fuel when smoking or around an

open ame or sparks.

– Do not remove the fuel cap or add fuel to the

tank while the engine is running or hot.

– If you spill fuel, do not attempt to start the

engine. A void creating a source of ignition until

the fuel vapors have dissipated.

– Store fuel in an approved container and keep

it out of the reach of children.

•Fuel is harmful or fatal if swallowed. Long-term

exposure to vapors can cause serious injury and

illness.

– A void prolonged breathing of vapors.

– Keep your hands and face away from the

nozzle and the fuel-tank opening.

– Keep fuel away from your eyes and skin.

Filling the Fuel T ank

T ype Unleaded gasoline

Minimum octane rating

87 (US) or 91 (research

octane; outside the US)

Ethanol

No more than 10% by volume

Methanol None

MTBE (methyl tertiary butyl

ether)

Less than 15% by volume

Oil Do not add to the fuel

Use only clean, fresh (no more than 30 days old), fuel

from a reputable source.

Important: T o reduce starting problems, add fuel

stabilizer/conditioner to fresh fuel as directed by

the fuel-stabilizer/conditioner manufacturer .

Refer to your engine owner ’ s manual for additional

information.

Fill the fuel tank as shown in Figure 9 .

g230458

Figure 9

10

Checking the Engine-Oil Level

Service Interval : Before each use or daily

Important: If the oil level in the crankcase is too low or too high and you run the engine, you may

damage the engine.

g231765

Figure 10

1 1

Adjusting the Handle Height

Y ou may raise or lower the handle to a position comfortable for you.

Rotate the handle lock, move the handle to 1 of 2 positions, and lock the handle into position ( Figure 1 1 ).

g334366

Figure 1 1

Adjusting the Cutting Height

CAUTION

If the engine has been running, the mufer will be hot and can burn you.

Keep away from the hot mufer .

Adjust the cutting height as desired. Set all wheels to the same cutting height ( Figure 12 ).

g369225

Figure 12

12

During Operation

During Operation Safety

General Safety

•W ear appropriate clothing, including eye

protection; long pants; substantial, slip-resistant

footwear; and hearing protection. T ie back long

hair and do not wear loose clothing or loose

jewelry .

•Use your full attention while operating the

machine. Do not engage in any activity that

causes distractions; otherwise, injury or property

damage may occur .

•Do not operate the machine while ill, tired, or

under the inuence of alcohol or drugs.

•The blade is sharp; contacting the blade can result

in serious personal injury . Shut of f the engine and

wait for all moving parts to stop before leaving the

operating position.

•When you release the blade-control bar , the

engine should shut of f and the blade should stop

within 3 seconds. If not, stop using your machine

immediately and contact an Authorized Service

Dealer .

•Keep bystanders out of the operating area. Keep

small children out of the operating area and under

the watchful care of a responsible adult who is

not operating the machine. Stop the machine if

anyone enters the area.

•Always look down and behind you before moving

the machine in reverse.

•Operate the machine only in good visibility and

appropriate weather conditions. Do not operate

the machine when there is the risk of lightning.

•W et grass or leaves can cause serious injury if

you slip and contact the blade. A void mowing in

wet conditions.

•Use extreme care when approaching blind

corners, shrubs, trees, or other objects that may

block your view .

•Do not direct the discharge material toward

anyone. A void discharging material against a wall

or obstruction; material may ricochet toward you.

Stop the blade(s) when crossing gravel surfaces.

•W atch for holes, ruts, bumps, rocks, or other

hidden objects. Uneven terrain could cause you

to lose your balance or footing.

•If the machine strikes an object or starts to

vibrate, immediately shut of f the engine, wait for

all moving parts to stop, and disconnect the wire

from the spark plug before examining the machine

for damage. Make all necessary repairs before

resuming operation.

•Before leaving the operating position, shut of f the

engine and wait for all moving parts to stop.

•If the engine has been running, it will be hot and

can severely burn you. Keep away from the hot

engine.

•Operate the engine only in well-ventilated areas.

Exhaust gases contain carbon monoxide, which is

an odorless, deadly poison.

•Check the grass catcher components and the

discharge chute frequently for any wear or

deterioration and replace them with genuine T oro

parts when necessary .

Slope Safety

•Mow across the face of slopes; never up and

down. Use extreme caution when changing

direction on slopes.

•Do not mow on excessively steep slopes. Poor

footing could cause a slip-and-fall accident.

•Mow with caution near drop-of fs, ditches, or

embankments.

13

Starting the Engine

g352922

Figure 13

Note: If the machine does not start after several

attempts, contact an Authorized Service Dealer .

Using the Self-Propel Drive

T o operate the self-propel drive, simply walk with your

hands on the upper handle and your elbows at your

sides, and the machine will automatically keep pace

with you ( Figure 14 ).

g334136

Figure 14

Note: If the machine does not freely roll backward

after self-propelling, stop walking, hold your hands

in place, and allow the machine to roll a couple of

centimeters (inches) forward to disengage the wheel

drive. Y ou can also try reaching just under the upper

handle to the metal handle and pushing the machine

forward a couple of centimeters (inches). If the

machine still does not roll backward easily , contact an

Authorized Service Dealer .

Shutting Off the Engine

Service Interval : Before each use or daily —Ensure

that the engine shuts of f within

3 seconds after releasing the

blade-control bar .

T o shut of f the engine, release the blade-control bar .

Important: When you release the blade-control

bar , both the engine and blade should stop within

3 seconds. If they do not stop properly , stop

using your machine immediately and contact an

Authorized Service Dealer .

14

Recycling the Clippings

Y our machine comes from the factory ready to recycle the grass and leaf clippings back into the lawn.

If the grass bag is on the machine, remove it before recycling the clippings. Refer to Removing the Grass Bag

( page 16 ) .

Bagging the Clippings

Use the grass bag when you want to collect grass and leaf clippings from the lawn.

W ARNING

A worn grass bag could allow small stones and other similar debris to be thrown toward you

or bystanders, resulting in serious personal injury or death.

Check the grass bag frequently . If it is damaged, install a new T oro replacement bag.

W ARNING

The blades are sharp; contacting the blades can result in serious personal injury .

Shut off the machine and wait for all moving parts to stop before leaving the operating position.

Installing the Grass Bag

1. Shut of f the machine and wait for all moving parts to stop.

2. Raise and hold up the rear deector (A of Figure 15 ).

3. Remove the rear-discharge plug by pushing in the latch with your thumb and pulling the plug out from

the machine (B and C of Figure 15 ).

4. Install the bag-rod ends into the notches at the base of the handle, and rock the bag back and forth to

ensure that the bag-rod ends are seated at the bottom of both notches (D of Figure 15 ).

5. Lower the rear deector until it rests on the grass bag.

g367752

Figure 15

15

Removing the Grass Bag

DANGER

The machine can throw grass clippings and other objects through an opening in the machine

housing. Objects thrown with enough force could cause serious personal injury or death to

you or to bystanders.

• Never remove the grass bag and then start the machine without the discharge plug installed

on the machine.

• Never open the rear deector on the machine when the machine is running.

1. Shut of f the machine and wait for all moving parts to stop.

2. Raise the rear deector .

3. Remove the bag rod on the grass bag from the notches at the base of the handle (A of Figure 15 ).

4. Install the discharge plug (B of Figure 15 ).

5. Lower the rear deector (C of Figure 15 ).

Operating T ips

General Mowing T ips

•Inspect the area where you will use the machine

and remove all objects that the machine could

throw .

•A void striking solid objects with the blade. Never

deliberately mow over any object.

•If the machine strikes an object or starts to vibrate,

immediately shut of f the engine, wait for all moving

parts to stop, disconnect the wire from the spark

plug, and examine the machine for damage.

•For best performance, install a new T oro blade

before the cutting season begins or when

necessary .

Cutting Grass

•Cut only about a third of the grass blade at a time.

Do not cut below 51 mm (2 inches) unless the

grass is sparse or it is late fall when grass growth

begins to slow down.

•When cutting grass over 15 cm (6 inches) tall,

mow at the highest cutting height setting and walk

slower; then mow again at a lower setting for the

best lawn appearance. If the grass is too long, the

machine may plug and cause the engine to stall.

•W et grass and leaves tend to clump on the yard

and can cause the machine to plug or the engine

to stall. A void mowing in wet conditions.

•Be aware of a potential re hazard in very dry

conditions, follow all local re warnings, and keep

the machine free of dry grass and leaf debris.

•Alternate the mowing direction. This helps

disperse the clippings over the lawn for even

fertilization.

•If the nished lawn appearance is unsatisfactory ,

try 1 or more of the following:

– Replace the blade or have it sharpened.

– W alk at a slower pace while mowing.

– Raise the cutting height on your machine.

– Cut the grass more frequently .

– Overlap cutting swaths instead of cutting a full

swath with each pass.

Cutting Leaves

•After cutting the lawn, ensure that half of the lawn

shows through the cut leaf cover . Y ou may need

to make more than a single pass over the leaves.

•If there are more than 13 cm (5 inches) of leaves

on the lawn, mow at a higher cutting height and

then again at the desired cutting height.

•Slow down your mowing speed if the machine

does not cut the leaves nely enough.

16

After Operation

After Operation Safety

General Safety

•Always shut of f the machine, wait for all moving

parts to stop, and allow the machine to cool before

adjusting, servicing, cleaning, or storing it.

•Clean grass and debris from the machine to help

prevent res. Clean up oil or fuel spills.

•Never store the machine or fuel container where

there is an open ame, spark, or pilot light, such

as on a water heater or on other appliances.

Hauling Safety

•Use care when loading or unloading the machine.

•Secure the machine from rolling.

Cleaning Under the

Machine

Service Interval : After each use

For best results, clean under the machine shortly after

you have completed mowing.

Cleaning Under the Machine in the

Operating Position

1. Lower the machine to its lowest cutting-height

setting.

2. Move the machine onto a paved level surface.

3. With the engine running and the blade engaged,

spray a stream of water in front of the right , rear

wheel ( Figure 16 ).

Note: The water will splash into the path of the

blade, cleaning out the clippings.

g002600

Figure 16

4. When no more clippings come out, stop the

water and move the machine to a dry area.

5. Start the engine and run it for a few minutes to

dry the underside of the machine to prevent it

from rusting.

6. Shut of f the engine, remove the electric-start

button (if equipped), and allow the machine to

cool before storing it in an enclosed area.

Cleaning under the Machine in the

V ertical-stow Position

1. Set the machine in the vertical-stow position;

refer to Storing the Machine in the V ertical-Stow

Position ( page 19 ) .

2. W ash out the clippings from under the machine.

17

Folding the Handle

W ARNING

Folding or unfolding the handle improperly can damage the cables, causing an unsafe

operating condition.

• Do not damage the cables when folding or unfolding the handle.

• If a cable is damaged, contact an Authorized Service Dealer .

1. Hold the handle while disengaging the handle locks to avoid pinching your hands.

2. Disengage the handle locks until you can move the upper handle freely (A of Figure 17 )

3. Fold the handle forward to the fully forward position (B of Figure 17 ).

Important: Route the cables to the outside of the handle locks as you fold the handle.

g334367

Figure 17

4. T o unfold the handle, refer to 1 Assembling and Unfolding the Handle ( page 5 ) .

18

La page charge ...

Toro Super Recycler C53AST 53 cm Lawn Mower Manuel utilisateur

Toro Super Recycler C53AST 53 cm Lawn Mower Manuel utilisateur

dans d''autres langues

Documents connexes