Toro Super Recycler C53AST 53 cm Lawn Mower Manuel utilisateur

Catégorie
Tondeuses à gazon
Taper
Manuel utilisateur
Form No. 3450-890 Rev D
53cm Super Recycler
®
Lawn Mower
21693
Super Recycler
®
Rasenmäher (53 cm)
21693
T ondeuse Super Recycler
®
de 53 cm
21693
53 cm Super Recycler
®
gazonmaaier
21693
www .T oro.com.
*3450-890*
Form No. 3450-878 Rev D
53cm Super Recycler
®
Lawn Mower
Model No. 21693 —Serial No. 400000000 and Up
Operator's Manual
Introduction
This rotary-blade, walk-behind lawn mower is intended
to be used by residential homeowners. It is designed
primarily for cutting grass on well-maintained lawns on
residential properties. Using this product for purposes
other than its intended use could prove dangerous to
you and bystanders.
Read this information carefully to learn how to operate
and maintain your product properly and to avoid
injury and product damage. Y ou are responsible for
operating the product properly and safely .
V isit www .T oro.com for more information, including
safety tips, training materials, accessory information,
help nding a dealer , or to register your product.
Whenever you need service, genuine T oro parts, or
additional information, contact an Authorized Service
Dealer or T oro Customer Service and have the model
and serial numbers of your product ready . Figure 1
identies the location of the model and serial numbers
on the product. W rite the numbers in the space
provided.
Important: W ith your mobile device, you can
scan the QR code on the serial number decal (if
equipped) to access warranty , parts, and other
product information
g374302
Figure 1
1. Model and serial number location
Model No.
Serial No.
Safety-Alert Symbol
The safety-alert symbol ( Figure 2 ) shown in this
manual and on the machine identies important safety
messages that you must follow to prevent accidents.
g000502
Figure 2
Safety-alert symbol
The safety-alert symbol appears above information
that alerts you to unsafe actions or situations and
is followed by the word DANGER ,W ARNING , or
CAUTION .
DANGER indicates an imminently hazardous situation
which, if not avoided, will result in death or serious
injury .
W ARNING indicates a potentially hazardous situation
which, if not avoided, could result in death or serious
injury .
CAUTION indicates a potentially hazardous situation
which, if not avoided, may result in minor or moderate
injury .
This manual uses two other words to highlight
information. Important calls attention to special
mechanical information and Note emphasizes general
information worthy of special attention.
This product complies with all relevant European
directives; for details, please see the separate product
specic Declaration of Conformity (DOC) sheet.
Gross or Net T orque: The gross or net torque
of this engine was laboratory rated by the engine
manufacturer in accordance with the Society of
Automotive Engineers (SAE) J1940 or J2723. As
congured to meet safety , emission, and operating
requirements, the actual engine torque on this class
of mower will be signicantly lower . Please refer to
the engine manufacturer ’ s information included with
the machine.
Do not tamper with or disable safety devices on the
machine, and check their proper operation regularly .
Do not attempt to adjust or tamper with the engine
© 2023—The T oro® Company
81 1 1 L yndale A venue South
Bloomington, MN 55420
Register at www .T oro.com.
Original Instructions (EN)
Printed in Mexico
All Rights Reserved
*3450-878*
speed control; doing so may create an unsafe
operating condition, resulting in personal injury .
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Safety-Alert Symbol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Safety ....................................................................... 3
General Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Safety and Instructional Decals . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Setup ........................................................................ 5
1 Assembling and Unfolding the Handle . . . . . . . . . . . . . . 5
2 Installing the Blade-Control Bar . . . . . . . . . . . . . . . . . . . . . . . . 5
3 Installing the Recoil-Starter Rope in the
Rope Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4 Adding Oil to the Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5 Assembling the Grass Bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Attachments/Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Before Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Before Operation Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Filling the Fuel T ank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Checking the Engine-Oil Level . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1
Adjusting the Handle Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Adjusting the Cutting Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
During Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
During Operation Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Starting the Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Using the Self-Propel Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Shutting Of f the Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Recycling the Clippings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Bagging the Clippings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Operating T ips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
After Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
After Operation Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Cleaning Under the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Folding the Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Storing the Machine in the V ertical-Stow
Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Recommended Maintenance Schedule(s) . . . . . . . . . . . 21
Maintenance Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Preparing for Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Servicing the Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Changing the Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Replacing the Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Adjusting the Self-Propel Drive . . . . . . . . . . . . . . . . . . . . . . . . . 24
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Storage Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Preparing the Machine for Storage . . . . . . . . . . . . . . . . . . . 25
Removing the Machine from Storage . . . . . . . . . . . . . . . . 25
2
Safety
General Safety
This product is capable of amputating hands and
feet and of throwing objects. Always follow all safety
instructions to avoid serious personal injury or death.
Read, understand, and follow the instructions
and warnings in this Operator ’ s Manual and on
the machine and attachments before starting the
engine.
Do not put your hands or feet near moving parts or
under the machine. Keep clear of any discharge
opening.
Do not operate the machine without all guards
and other safety protective devices in place and
functioning properly on the machine.
Keep bystanders and children out of the operating
area. Do not allow children to operate the machine.
Allow only people who are responsible, trained,
familiar with the instructions, and physically
capable to operate the machine.
Stop the machine, shut of f the engine, and wait for
all moving parts to stop before servicing, fueling,
or unclogging the machine.
Improperly using or maintaining this machine can
result in injury . T o reduce the potential for injury ,
comply with these safety instructions and always
pay attention to the safety-alert symbol , which
means Caution, W arning, or Danger—personal safety
instruction. Failure to comply with these instructions
may result in personal injury or death.
Safety and Instructional
Decals
Safety decals and instructions are
easily visible to the operator and are
located near any area of potential
danger . Replace any decal that is
damaged or missing.
decaloemmarkt
Manufacturer's Mark
1. This mark indicates that the blade is identied as a part
from the original machine manufacturer .
decal1 12-8760
1 12-8760
1. Thrown object hazard—keep bystanders away .
2. Cutting/dismemberment hazard of hand or foot, mower
blade—stay away from moving parts.
3
decal131-4514
131-4514
1. W arning—read the Operator's Manual .
2. Cutting/dismemberment hazard of hand, mower
blade—stay away from moving parts; keep all guards and
shields in place.
3. Cutting/dismemberment hazard of hand, mower
blade—disconnect the spark-plug wire before performing
maintenance.
4. Thrown object hazard—keep bystanders away; shut of f the
engine before leaving the operating position; pick up any
debris before mowing.
5. Cutting/dismemberment hazard of foot, mower blade—do
not operate up and down slopes; operate side to side on
slopes; look behind you when moving in reverse.
decal133-8198
133-8198
1. W arning—read the Operator's Manual ; add fuel up to the
indicated level, then tip the machine onto the rear wheels
for storage.
4
Setup
Important: Remove and discard the protective plastic sheet that covers the engine and any other
plastic or wrapping on the machine.
1
Assembling and Unfolding the Handle
No Parts Required
Procedure
W ARNING
Assembling and unfolding the handle improperly can damage the cables, causing an unsafe
operating condition.
• Do not damage the cables when assembling and unfolding the handle.
Ensure that the cables are routed to the outside of the handle.
If a cable is damaged, contact an Authorized Service Dealer .
g367755
Figure 3
5
2
Installing the Blade-Control Bar
No Parts Required
Procedure
g344378
Figure 4
3
Installing the Recoil-Starter
Rope in the Rope Guide
No Parts Required
Procedure
Important: T o start the engine safely and easily whenever you use the machine, install the recoil-starter
rope in the rope guide.
g334093
Figure 5
6
4
Adding Oil to the Engine
No Parts Required
Procedure
Important: If the oil level in the engine is too low or too high and you run the engine, you may damage
the engine.
g222533
Figure 6
7
5
Assembling the Grass Bag
No Parts Required
Procedure
g334351
Figure 7
8
Product Overview
g367232
Figure 8
1. Handle
7. Cutting-height lever (4)
2. Blade-control bar
8. Spark plug
3. Adjustment for the
self-propel drive
9. Oil ll/dipstick
4. Rear deector 10. Handle knob (2)
5. Fuel-tank cap
1 1. Grass bag
6. Air lter
12. Recoil-start handle
Specications
Model W eight Length W idth Height
38 kg21693
(84 lb)
164 cm 58 cm 106 cm
Attachments/Accessories
A selection of T oro approved attachments and
accessories is available for use with the machine
to enhance and expand its capabilities. Contact
your Authorized Service Dealer or authorized T oro
distributor or go to www .T oro.com for a list of all
approved attachments and accessories.
T o ensure optimum performance and continued safety
certication of the machine, use only genuine T oro
replacement parts and accessories. Replacement
parts and accessories made by other manufacturers
could be dangerous, and such use could void the
product warranty .
9
Operation
Note: Determine the left and right sides of the
machine from the normal operating position.
Before Operation
Before Operation Safety
General Safety
Always shut of f the machine, wait for all moving
parts to stop, and allow the machine to cool before
adjusting, servicing, cleaning, or storing it.
Become familiar with the safe operation of the
equipment, operator controls, and safety signs.
Check that all guards and safety devices, such as
deectors and/or grass catcher , are in place and
functioning properly .
Always inspect the machine to ensure that the
blades and blade bolts are not worn or damaged.
Inspect the area where you will use the machine,
and remove all objects that could interfere with
the operation of the machine or that the machine
could throw .
Contact with the moving blade will cause serious
injury . Do not put your ngers under the housing.
Fuel Safety
Fuel is extremely ammable and highly explosive.
A re or explosion from fuel can burn you and
others and can damage property .
T o prevent a static charge from igniting the fuel,
place the container and/or machine directly on
the ground before lling, not in a vehicle or on
an object.
Fill the fuel tank outdoors, in an open area,
when the engine is cold. Wipe up any fuel that
spills.
– Do not handle fuel when smoking or around an
open ame or sparks.
Do not remove the fuel cap or add fuel to the
tank while the engine is running or hot.
If you spill fuel, do not attempt to start the
engine. A void creating a source of ignition until
the fuel vapors have dissipated.
Store fuel in an approved container and keep
it out of the reach of children.
Fuel is harmful or fatal if swallowed. Long-term
exposure to vapors can cause serious injury and
illness.
A void prolonged breathing of vapors.
– Keep your hands and face away from the
nozzle and the fuel-tank opening.
– Keep fuel away from your eyes and skin.
Filling the Fuel T ank
T ype Unleaded gasoline
Minimum octane rating
87 (US) or 91 (research
octane; outside the US)
Ethanol
No more than 10% by volume
Methanol None
MTBE (methyl tertiary butyl
ether)
Less than 15% by volume
Oil Do not add to the fuel
Use only clean, fresh (no more than 30 days old), fuel
from a reputable source.
Important: T o reduce starting problems, add fuel
stabilizer/conditioner to fresh fuel as directed by
the fuel-stabilizer/conditioner manufacturer .
Refer to your engine owner ’ s manual for additional
information.
Fill the fuel tank as shown in Figure 9 .
g230458
Figure 9
10
Checking the Engine-Oil Level
Service Interval : Before each use or daily
Important: If the oil level in the crankcase is too low or too high and you run the engine, you may
damage the engine.
g231765
Figure 10
1 1
Adjusting the Handle Height
Y ou may raise or lower the handle to a position comfortable for you.
Rotate the handle lock, move the handle to 1 of 2 positions, and lock the handle into position ( Figure 1 1 ).
g334366
Figure 1 1
Adjusting the Cutting Height
CAUTION
If the engine has been running, the mufer will be hot and can burn you.
Keep away from the hot mufer .
Adjust the cutting height as desired. Set all wheels to the same cutting height ( Figure 12 ).
g369225
Figure 12
12
During Operation
During Operation Safety
General Safety
W ear appropriate clothing, including eye
protection; long pants; substantial, slip-resistant
footwear; and hearing protection. T ie back long
hair and do not wear loose clothing or loose
jewelry .
Use your full attention while operating the
machine. Do not engage in any activity that
causes distractions; otherwise, injury or property
damage may occur .
Do not operate the machine while ill, tired, or
under the inuence of alcohol or drugs.
The blade is sharp; contacting the blade can result
in serious personal injury . Shut of f the engine and
wait for all moving parts to stop before leaving the
operating position.
When you release the blade-control bar , the
engine should shut of f and the blade should stop
within 3 seconds. If not, stop using your machine
immediately and contact an Authorized Service
Dealer .
Keep bystanders out of the operating area. Keep
small children out of the operating area and under
the watchful care of a responsible adult who is
not operating the machine. Stop the machine if
anyone enters the area.
Always look down and behind you before moving
the machine in reverse.
Operate the machine only in good visibility and
appropriate weather conditions. Do not operate
the machine when there is the risk of lightning.
W et grass or leaves can cause serious injury if
you slip and contact the blade. A void mowing in
wet conditions.
Use extreme care when approaching blind
corners, shrubs, trees, or other objects that may
block your view .
Do not direct the discharge material toward
anyone. A void discharging material against a wall
or obstruction; material may ricochet toward you.
Stop the blade(s) when crossing gravel surfaces.
W atch for holes, ruts, bumps, rocks, or other
hidden objects. Uneven terrain could cause you
to lose your balance or footing.
If the machine strikes an object or starts to
vibrate, immediately shut of f the engine, wait for
all moving parts to stop, and disconnect the wire
from the spark plug before examining the machine
for damage. Make all necessary repairs before
resuming operation.
Before leaving the operating position, shut of f the
engine and wait for all moving parts to stop.
If the engine has been running, it will be hot and
can severely burn you. Keep away from the hot
engine.
Operate the engine only in well-ventilated areas.
Exhaust gases contain carbon monoxide, which is
an odorless, deadly poison.
Check the grass catcher components and the
discharge chute frequently for any wear or
deterioration and replace them with genuine T oro
parts when necessary .
Slope Safety
Mow across the face of slopes; never up and
down. Use extreme caution when changing
direction on slopes.
Do not mow on excessively steep slopes. Poor
footing could cause a slip-and-fall accident.
Mow with caution near drop-of fs, ditches, or
embankments.
13
Starting the Engine
g352922
Figure 13
Note: If the machine does not start after several
attempts, contact an Authorized Service Dealer .
Using the Self-Propel Drive
T o operate the self-propel drive, simply walk with your
hands on the upper handle and your elbows at your
sides, and the machine will automatically keep pace
with you ( Figure 14 ).
g334136
Figure 14
Note: If the machine does not freely roll backward
after self-propelling, stop walking, hold your hands
in place, and allow the machine to roll a couple of
centimeters (inches) forward to disengage the wheel
drive. Y ou can also try reaching just under the upper
handle to the metal handle and pushing the machine
forward a couple of centimeters (inches). If the
machine still does not roll backward easily , contact an
Authorized Service Dealer .
Shutting Off the Engine
Service Interval : Before each use or daily —Ensure
that the engine shuts of f within
3 seconds after releasing the
blade-control bar .
T o shut of f the engine, release the blade-control bar .
Important: When you release the blade-control
bar , both the engine and blade should stop within
3 seconds. If they do not stop properly , stop
using your machine immediately and contact an
Authorized Service Dealer .
14
Recycling the Clippings
Y our machine comes from the factory ready to recycle the grass and leaf clippings back into the lawn.
If the grass bag is on the machine, remove it before recycling the clippings. Refer to Removing the Grass Bag
( page 16 ) .
Bagging the Clippings
Use the grass bag when you want to collect grass and leaf clippings from the lawn.
W ARNING
A worn grass bag could allow small stones and other similar debris to be thrown toward you
or bystanders, resulting in serious personal injury or death.
Check the grass bag frequently . If it is damaged, install a new T oro replacement bag.
W ARNING
The blades are sharp; contacting the blades can result in serious personal injury .
Shut off the machine and wait for all moving parts to stop before leaving the operating position.
Installing the Grass Bag
1. Shut of f the machine and wait for all moving parts to stop.
2. Raise and hold up the rear deector (A of Figure 15 ).
3. Remove the rear-discharge plug by pushing in the latch with your thumb and pulling the plug out from
the machine (B and C of Figure 15 ).
4. Install the bag-rod ends into the notches at the base of the handle, and rock the bag back and forth to
ensure that the bag-rod ends are seated at the bottom of both notches (D of Figure 15 ).
5. Lower the rear deector until it rests on the grass bag.
g367752
Figure 15
15
Removing the Grass Bag
DANGER
The machine can throw grass clippings and other objects through an opening in the machine
housing. Objects thrown with enough force could cause serious personal injury or death to
you or to bystanders.
Never remove the grass bag and then start the machine without the discharge plug installed
on the machine.
• Never open the rear deector on the machine when the machine is running.
1. Shut of f the machine and wait for all moving parts to stop.
2. Raise the rear deector .
3. Remove the bag rod on the grass bag from the notches at the base of the handle (A of Figure 15 ).
4. Install the discharge plug (B of Figure 15 ).
5. Lower the rear deector (C of Figure 15 ).
Operating T ips
General Mowing T ips
Inspect the area where you will use the machine
and remove all objects that the machine could
throw .
A void striking solid objects with the blade. Never
deliberately mow over any object.
If the machine strikes an object or starts to vibrate,
immediately shut of f the engine, wait for all moving
parts to stop, disconnect the wire from the spark
plug, and examine the machine for damage.
For best performance, install a new T oro blade
before the cutting season begins or when
necessary .
Cutting Grass
Cut only about a third of the grass blade at a time.
Do not cut below 51 mm (2 inches) unless the
grass is sparse or it is late fall when grass growth
begins to slow down.
When cutting grass over 15 cm (6 inches) tall,
mow at the highest cutting height setting and walk
slower; then mow again at a lower setting for the
best lawn appearance. If the grass is too long, the
machine may plug and cause the engine to stall.
W et grass and leaves tend to clump on the yard
and can cause the machine to plug or the engine
to stall. A void mowing in wet conditions.
Be aware of a potential re hazard in very dry
conditions, follow all local re warnings, and keep
the machine free of dry grass and leaf debris.
Alternate the mowing direction. This helps
disperse the clippings over the lawn for even
fertilization.
If the nished lawn appearance is unsatisfactory ,
try 1 or more of the following:
Replace the blade or have it sharpened.
W alk at a slower pace while mowing.
– Raise the cutting height on your machine.
– Cut the grass more frequently .
Overlap cutting swaths instead of cutting a full
swath with each pass.
Cutting Leaves
After cutting the lawn, ensure that half of the lawn
shows through the cut leaf cover . Y ou may need
to make more than a single pass over the leaves.
If there are more than 13 cm (5 inches) of leaves
on the lawn, mow at a higher cutting height and
then again at the desired cutting height.
Slow down your mowing speed if the machine
does not cut the leaves nely enough.
16
After Operation
After Operation Safety
General Safety
Always shut of f the machine, wait for all moving
parts to stop, and allow the machine to cool before
adjusting, servicing, cleaning, or storing it.
Clean grass and debris from the machine to help
prevent res. Clean up oil or fuel spills.
Never store the machine or fuel container where
there is an open ame, spark, or pilot light, such
as on a water heater or on other appliances.
Hauling Safety
Use care when loading or unloading the machine.
Secure the machine from rolling.
Cleaning Under the
Machine
Service Interval : After each use
For best results, clean under the machine shortly after
you have completed mowing.
Cleaning Under the Machine in the
Operating Position
1. Lower the machine to its lowest cutting-height
setting.
2. Move the machine onto a paved level surface.
3. With the engine running and the blade engaged,
spray a stream of water in front of the right , rear
wheel ( Figure 16 ).
Note: The water will splash into the path of the
blade, cleaning out the clippings.
g002600
Figure 16
4. When no more clippings come out, stop the
water and move the machine to a dry area.
5. Start the engine and run it for a few minutes to
dry the underside of the machine to prevent it
from rusting.
6. Shut of f the engine, remove the electric-start
button (if equipped), and allow the machine to
cool before storing it in an enclosed area.
Cleaning under the Machine in the
V ertical-stow Position
1. Set the machine in the vertical-stow position;
refer to Storing the Machine in the V ertical-Stow
Position ( page 19 ) .
2. W ash out the clippings from under the machine.
17
Folding the Handle
W ARNING
Folding or unfolding the handle improperly can damage the cables, causing an unsafe
operating condition.
• Do not damage the cables when folding or unfolding the handle.
If a cable is damaged, contact an Authorized Service Dealer .
1. Hold the handle while disengaging the handle locks to avoid pinching your hands.
2. Disengage the handle locks until you can move the upper handle freely (A of Figure 17 )
3. Fold the handle forward to the fully forward position (B of Figure 17 ).
Important: Route the cables to the outside of the handle locks as you fold the handle.
g334367
Figure 17
4. T o unfold the handle, refer to 1 Assembling and Unfolding the Handle ( page 5 ) .
18
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112

Toro Super Recycler C53AST 53 cm Lawn Mower Manuel utilisateur

Catégorie
Tondeuses à gazon
Taper
Manuel utilisateur