Ingersoll-Rand UP6 25 Operation and Maintenance Manual

UP6 15, UP6 20, UP6 25, UP6 30

60Hz

This manual contains

important safety information

and must be made available

to personnel who operate and

maintain this machine.

C.C.N.: 80445158

REV. A

DATE : OCTOBER 2008

OPERATION AND MAINTENANCE MANUAL

:

Warranty

The Company warrants that the equipment manufactured by it and delivered hereunder will be free of defects in

material and workmanship for a period of twelve months from the date of placing the Equipment in operation or eighteen

months from the date of shipment from the factory, whichever shall first occur. The Purchaser shall be obligated to

promptly report any failure to conform to this warranty, in writing to the Company in said period, whereupon the

Company shall, at its option, correct such nonconformity, by suitable repair to such equipment or, furnish a replacement

part F.O.B. point of shipment, provided the Purchaser has stored, installed, maintained and operated such Equipment

in accordance with good industry practices and has complied with specific recommendations of the Company.

Accessories or equipment furnished by the Company, but manufactured by others, shall carry whatever warranty the

manufacturers have conveyed to the Company and which can be passed on to the Purchaser. The Company shall

not be liable for any repairs, replacements, or adjustments to the Equipment or any costs of labor performed by the

Purchaser or others without Company‘s prior written approval.

The effects of corrosion, erosion and normal wear and tear are specifically excluded. Performance warranties are

limited to those specifically stated within the Company‘s proposal. Unless responsibility for meeting such performance

warranties are limited to specified tests, the Company‘s obligation shall be to correct in the manner and for the period

of time provided above.

THE COMPANY MAKES NO OTHER WARRANTY OR REPRESENTATION OF ANY KIND WHATSOEVER,

EXPRESSED OR IMPLIED, EXCEPT THAT OF TITLE, AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED.

Correction by the Company of nonconformities whether patent or latent, in the manner and for the period of time

provided above, shall constitute fulfillment of all liabilities of the Company for such nonconformities whether based on

contract, warranty negligence, indemnity, strict liability or otherwise with respect to or arising out of such Equipment.

The purchaser shall not operate Equipment which is considered to be defective, without first notifying the Company

in writing of its intention to do so. Any such use of Equipment will be at Purchaser‘s sole risk and liability

.

BONDED WARRANTY & REGISTERED START UP

Note that this is Ingersoll Rand standard warranty. Any warranty in force at the time of purchase of the compressor

or negotiated as part of the purchase order may take precedence over this warranty.

CONTENTS & ABBREVIATIONS

1

CONTENTS

1 CONTENTS

2 FOREWORD

3 DECALS

8 SAFETY

10 GENERAL INFORMATION

12 INSTALLATION / HANDLING

21 OPERATING INSTRUCTIONS

25 MAINTENANCE

31 TROUBLE SHOOTING

ABBREVIATIONS & SYMBOLS

#### Contact Ingersoll Rand for serial number

–>#### Up to Serial No.

####–> From Serial No.

* Not illustrated

{ Option

NR Not required

AR As required

SM Sitemaster/Sitepack

HA High ambient machine

WC Watercooled machine

AC Aircooled machine

ERS Energy recovery system

T.E.F.C. Totally enclosed fan cooled motor (IP55)

O.D.P. Open drip proof (motor)

FOREWORD

2

The contents of this manual are considered to be proprietary and

confidential to Ingersoll Rand and should not be reproduced without

the prior written permission of Ingersoll Rand.

Nothing contained in this document is intended to extend any

promise, warranty or representation, expressed or implied, regarding

the Ingersoll Rand products described herein. Any such warranties or

other terms and conditions of sale of products shall be in accordance

with the standard terms and conditions of sale for such products, which

are available upon request.

This manual contains instructions and technical data to cover

routine operation and scheduled maintenance tasks by operation and

maintenance staff. Major overhauls are outside the scope of this

manual and should be referred to an authorized Ingersoll Rand service

department.

All components, accessories, pipes and connectors added to the

compressed air system should be:

. of good quality, procured from a reputable manufacturer and,

wherever possible, be of a type approved by Ingersoll Rand.

. clearly rated for a pressure at least equal to the machine maximum

allowable working pressure.

. compatible with the compressor lubricant/coolant.

. accompanied with instructions for safe installation, operation and

maintenance.

Details of approved equipment are available from Ingersoll Rand

Service departments.

The use of non–genuine spare repair parts other than those

included within the Ingersoll Rand approved parts list may create

hazardous conditions over which Ingersoll Rand has no control.

Therefore Ingersoll Rand does not accept any liabilitity for losses

caused by equipment in which non–approved repair parts are installed.

Standard warranty conditions may be affected.

Ingersoll Rand reserves the right to make changes and

improvements to products without notice and without incurring any

obligation to make such changes or add such improvements to

products sold previously.

The intended uses of this machine are outlined below and examples

of unapproved usage are also given, however Ingersoll Rand cannot

anticipate every application or work situation that may arise.

IF IN DOUBT CONSULT SUPERVISION.

This machine has been designed and supplied for use only in the

following specified conditions and applications:

. Compression of normal ambient air containing no known or

detectable additional gases, vapors. or particles

. Operation within the ambient temperature range specified in the

GENERAL INFORMATION section of this manual.

The use of the machine in any of the situation types listed in

table 1:–

a) Is not approved by Ingersoll Rand,

b) May impair the safety of users and other persons, and

c) May prejudice any claims made against Ingersoll Rand.

TABLE 1

Use of the machine to produce compressed air for:

a) direct human consumption

b) indirect human consumption, without suitable filtration and purity

checks.

Use of the machine outside the ambient temperature range

specified in the GENERAL INFORMATION SECTION of this manual.

Use of the machine where there is any actual or foreseeable risk of

hazardous levels of flammable gases or vapors.

THIS MACHINE IS NOT INTENDED AND MUST NOT BE

USED IN POTENTIALLY EXPLOSIVE ATMOSPHERES,

INCLUDING SITUATIONS WHERE FLAMMABLE GASES OR

VAPORS MAY BE PRESENT.

Use of the machine fitted with non Ingersoll Rand approved

components.

Use of the machine with safety or control components missing or

disabled.

The company accepts no responsibility for errors in translation of

this manual from the original English version.

INGERSOLL RAND

DECALS 3

ISO SYMBOLS

GRAPHIC FORM AND MEANING OF ISO SYMBOLS

Prohibition / Mandatory Information / Instructions Warning

Use fork lift truck from this side only. RESET Do not use fork lift truck from this side.

Emergency stop. On (power). Off (power).

AUTOMATIC RESTART MAINTENANCE MAINTENANCE PROHIBITED

FRAGILE KEEP DRY THIS WAY UP

USE NO HOOKS NO SIDE CLAMPS HOURS

DECALS4

POWER INSPECT

Every X months, if sooner than required by

operating hours

CHANGE / REPLACE CLEAN

DECALS 5

ANSI SYMBOLS

GRAPHIC FORM AND MEANING OF ANSI SYMBOLS

DANGER

INTAKE AIR. Can contain carbon monoxide or other contaminants. Will cause serious injury or death. Ingersoll Rand

air compressors are not designed, intended or approved for breathing air. Compressed air should not be used for

breathing air applications unless treated in accordance with all applicable codes and regulations.

WARNING

HAZARDOUS VOLTAGE. Can cause serious injury or death. Disconnect power and bleed pressure from tank before

servicing. Lockout/Tagout machine. Compressor must be connected to properly grounded circuit. See Grounding

Instructions in manual. Do not operate compressor in wet conditions. Store indoors.

RISK OF FIRE OR EXPLOSION. Electrical arcing from compressor components can ignite flammable liquids and

vapors which can result in serious injury. Never operate the compressor near flammable liquids or vapors. If used to

spray flammable materials, keep compressor at least 20ft away from the spray area.

HIGH PRESSURE AIR. Rusted tanks can cause explosion and severe injury or death. Receiver under perssure.

Operator should relieve tank pressure before performing maintenance. In addition to automatic drain, operate manual

drain valve weekly. Manual drain valve located at bottom of the tank.

MOVING PARTS. Can cause serious injury. Do not operate with guards removed. Machine may start automatically.

Disconnect power before servicing. Lockout/Tagout machine.

HOT SURFACES. Can cause serious injury. Do not touch. Allow to cool before servicing. Do not touch hot

compressor or tubing.

EXPOSED MOVING BELTS AND SHEAVES.

Can cause severe injury or death.

Do not operate without guard in place. Disconnect power before servicing.

Lockout/Tagout machine.

Air flow exhaust may contain flying debris.

Safety protection should be worn at all times.

DECALS

6

VIEW BACK

VIEW LEFT

INSIDE PACKAGE

INSIDE STARTER DOOR

VIEW FRONT

VIEW RIGHT

60 Hz Units

VIEW TOP

SECTION A–A

Item ccn Qty. Description Item ccn Qty. Description

1 32343519 1 Decal, warning contaminated air

Located near air discharge port of receiver

tank on tank mounted units

2 32343576 1 Decal, air receiver auto–drain

3 93166460 1 Decal, coolant drain

4 32343501 1

Decal, dual voltage (if needed)

5–

6 23038466 1 Decal, Ingersoll Rand signature

horizontal 20“

7 23353147 1 Decal, maintenance parts

8 30286686 1 Decal, notice rotation

9 32343543 1 Decal, notice air discharge

Located near air discharge port of receiver

tank on tank mounted units

10 93171262 4 Decal, notice lift here

11 32343493 1 Decal, overload setting IEC starter

12 SPEC 1 Specifications, compressor package

13 32342669 1 Decal, starter box

14 32017469 1 Decal, voltage 120/1/60

† Optional position

7

DECALS

VIEW BACK

VIEW LEFT

INSIDE PACKAGE

INSIDE STARTER DOOR

VIEW FRONT

VIEW RIGHT

60 Hz Units

VIEW TOP

SECTION A–A

Item ccn Qty. Description Item ccn Qty. Description

15 32017436 1 Decal, voltage 230/3/60

32018475 1 Decal, voltage 200/3/60

32236481 1 Decal, voltage 380/3/60

32017444 1 Decal, voltage 460/3/60

32177305 1 Decal, voltage 575/3/60

16 32343527 1 Decal, warning high pressure

17 32343535 1 Decal, warning moving belts

18 32343550 3 Decal, warning exposed fan

19 32343568 2 Decal, warning hazardous voltage

20 32343584 1 Decal, warning hot surface

21 32343634 1 Decal, wiring schematic DOL 60Hz

32343642 1 Decal, wiring schematic Star Delta 60Hz

22 32343907 1 Decal, lock and tag out

23 32343899 1 Decal, warning flying debris

24 22115703 1 Tag, rotation 60Hz

25 32344095 2 Tag, shipping bracket

† Optional position

S A F E T Y

8

DANGER!

Hazard that WILL Cause DEATH, SEVERE INJURY or substantial

property damage if ignored. Instructions must be followed precisely to

avoid injury or death.

WARNING!

Hazard that CAN cause DEATH, SEVERE INJURY or substantial

property damage if ignored. Instructions which must be followed

precisely to avoid injury or death.

CAUTIONS!

Cautions call attention to instructions which must be followed

precisely to avoid damaging the product, process or its surroundings.

NOTES

Notes are used for supplementary information.

BREATHING AIR PRECAUTION

Ingersoll Rand air compressors are not designed, intended or

approved for breathing air. Compressed air should not be used for

breathing air applications unless treated in accordance with all

applicable codes and regulations.

General Information

Ensure that the operator reads and understands the decals and

consults the manuals before maintenance or operation.

Ensure that the Operation and Maintenance manual is not removed

permanently from the machine.

Ensure that maintenance personnel are adequately trained,

competent and have read the Maintenance Manuals.

Do not point air nozzles or sprayers toward anyone.

Compressed air and electricity can be dangerous. Before

undertaking any work on the compressor, ensure that the electrical

supply has been isolated and the compressor has been relieved of all

pressure.

Wear eye protection when operating or servicing compressor.

All persons positioned near to operating machinery should be

equipped with hearing protection and given instructions on its use in

accordance with workplace safety legislation.

Make sure that all protective covers are in place and that the

canopy/doors are closed during operation.

The specication of this machine is such that the machine is not

suitable for use in ammable gas risk areas.

Installation of this compressor must be in accordance with

recognised electrical codes and any local Health and Safety Codes.

The use of plastic bowls on line lters can be hazardous. Their

safety can be aected by either synthetic lubricants, or the additives

used in mineral oils. Ingersoll Rand recommends that only lters with

metal bowls should be used on a pressurized system.

Compressed air

Compressed air can be dangerous if incorrectly handled. Before

doing any work on the unit, ensure that all pressure is vented from the

system and that the machine cannot be started accidentally.

WARNING

Imposing a normal or emergency stop on the compressor will

only relieve pressure upstream of the minimum pressure valve on

top of the separator tank.

If maintenance work is required downstream of this valve, ensure

that all pressure is relieved at the process vent point external to

the compressor.

Ensure that the machine is operating at the rated pressure and that

the rated pressure is known to all relevant personnel.

All air pressure equipment installed in or connected to the machine

must have safe working pressure ratings of at least the machine rated

pressure.

If more than one compressor is connected to one common

downstream plant, eective isolation valves must be tted and

controlled by work procedures, so that one machine cannot accidentally

be pressurized / over pressurized by another.

Compressed air must not be used for a direct feed to any form of

breathing apparatus or mask.

The discharged air contains a very small percentage of compressor

lubricant and care should be taken to ensure that downstream

equipment is compatible.

If the discharged air is to be ultimately released into a conned

space, adequate ventilation must be provided.

When using compressed air always use appropriate personal

protective equipment.

All pressure containing parts, especially exible hoses and their

couplings, must be regularly inspected, be free from defects and be

replaced according to the Manual instructions.

Compressed air can be dangerous if incorrectly handled. Before

doing any work on the unit, ensure that all pressure is vented from the

system and that the machine cannot be started accidentally.

Avoid bodily contact with compressed air.

All safety valves located in the separator tank must be checked

periodically for correct operation.

Do not over–pressurize the receiver tank or similar vessels beyond

design limits.

Do not use a receiver tank or similar vessels that fail to meet the

design requirements of the compressor. Contact your distributor for

assistance.

Do not drill into, weld or otherwise alter the receiver tank or similar

vessels.

Materials

The following substances are used in the manufacture of this

machine and may be hazardous to health if used incorrectly:

. preservative grease

. rust preventative

. compressor coolant

AVOID INGESTION, SKIN CONTACT AND INHALATION OF

FUMES

Transport

When loading or transporting machines ensure that the specied

lifting and tie down points are used.

Lifting equipment must be properly rated for the weight of the

compressor.

Do not work on or walk under the compressor while it is suspended.

Electrical

Keep all parts of the body and any hand–held tools or other

conductive objects, away from exposed live parts of the compressor

electrical system. Maintain dry footing, stand on insulating surfaces

and do not contact any other portion of the compressor when making

adjustments or repairs to exposed live parts of the compressor

electrical system.

WARNING

Any electrical connections or adjustments should only be

made by a suitably qualied electrician.

Close and lock all access doors when the compressor is left

unattended.

Do not use extinguishers intended for Class A or Class B res on

electrical res. Use only extinguishers suitable for class BC or class

ABC res.

SAFETY

9

Attempt repairs only in clean, dry, well lighted and ventilated areas.

Connect the compressor only to electrical systems that are

compatiblewith its electrical characteristics and that are within it’s rated

capacity.

Condensate disposal

As waste water regulations vary by country and region it is the

responsibility of the user to establish the limitations and regulations in

their particular area. Ingersoll Rand and its associated distributors are

happy to advise and assist in these matters.

For further information, consult the Material Safety Data Sheets.

GENERAL INFORMATION

10

SEE TRANSFORMER NAMEPLATE FOR

WIRING CONNECTION REQUIREMENTS.

WYE (STAR) DELTA MOTOR

(OPEN TRANSITION)

“POWER ON”

OFF ON

“STAND BY”

“HI TEMP SHUTDOWN”

RESET

SEE NOTES

1 & 2

LINE

NUMBER

TO SUPPLY

JUMPER

LEGEND

CPT

Transformer, control

EDV

Valve, electric drain

E–STOP

Button, emergency stop

FU

Fuse

HM

Hourmeter

HATR

Relay, high air temperature

HATS

Switch, high air temperature

1M Contactor (main)

2M Contactor (delta)

OL

Overload, motor starter

PS

Switch, pressure

SS Switch, selector

S Contactor

(wye / star)

1SV Valve, solenoid (Load) N.C.

3SV Valve, solenoid (Blowdown) N.O.

TD Relay, Delta starting (10 second)

TR

Relay, auto restart time delay (6 min)

VAR Varistor

Terminal points

L1, L2, L3 Light, transformer type

NOTES

1. Approved fused disconnect or circuit breaker per code

requirements must be provided by customer.

2. Dashed lines represent wiring by customer.

3. Sizing of electrical components not supplied by Ingersoll Rand is

the responsibility of the customer and should be done in

accordance with the information on the compressor data plate

and local electrical codes.

4. Unit will not restart automaticlly after power outage.

5. Circuit shown in normal position de–energized.

6. All wiring to be in accordance with local codes.

GENERAL INFORMATION

11

SEE TRANSFORMER NAMEPLATE FOR

WIRING CONNECTION REQUIREMENTS.

COMPRESSOR

MOTOR

“POWER ON”

OFF ON

“STAND BY”

“HI TEMP SHUTDOWN”

RESET

SEE NOTES 1 & 2

LINE

NUMBER

TO SUPPLY

JUMPER

LEGEND

CPT

Transformer, control

EDV

Valve, electric drain

E–STOP

Button, emergency stop

FU

Fuse

HM

Hourmeter

HATR

Relay, high air temperature

HATS

Switch, high air temperature

M Contactor (main)

OL

Overload, motor starter

PS

Switch, pressure

SS Switch, selector

1SV Valve, solenoid (Load) N.C.

3SV Valve, solenoid (Blowdown) N.O.

TR

Relay, time delay (6 min)

VAR V

aristor

Terminal points

L1, L2, L3 Light, transformer type

NOTES

1. Approved fused disconnect or circuit breaker per code

requirements must be provided by customer.

2. Dashed lines represent wiring by customer.

3. Sizing of electrical components not supplied by Ingersoll Rand is

the responsibility of the customer and should be done in

accordance with the information on the compressor data plate

and local electrical codes.

4. Unit will not restart automatically after power outage.

5. Circuit shown in normal position de–energized.

6. All wiring to be in accordance with local codes.

INSTALLATION / HANDLING

12

ROTATION

VIEW LEFT

VIEW FRONT

VIEW RIGHT

VIEW TOP

VIEW BOTTOM

VIEW REAR

BASE MOUNTED UNITS

KEY

A Pre filter

B Compressor and cooling air intake

C Starter box

D Cooling air exhaust

E 1.00” NPT air discharge

F Customer power inlet

G Fork lift openings

(Fork lift hole covers must be installed after unit is in place to

reduce noise and ensure proper cooling of package)

H 4 slots 15 (0.6) x 25 (1.0)

See notes – Page 15

5

6

INSTALLATION / HANDLING

13

ROTATION

VIEW LEFT

VIEW FRONT

VIEW RIGHT

VIEW TOP

VIEW BOTTOM

VIEW REAR

TANK MOUNTED (120 GALLON)

60 Hz UNITS

KEY

A Pre filter

B Compressor and cooling air intake

C Starter box

D Cooling air exhaust

E 1.00” NPT air discharge

F Customer power inlet

G Fork lift openings

H Air receiver (120 gallons)

I Automatic drain valve

J 0.25 inch condensate drain

K 4 slots 17 (0.7) x 44 (1.8)

See notes – Page 15

INSTALLATION / HANDLING

14

ROTATION

VIEW LEFT

VIEW FRONT

VIEW RIGHT

VIEW TOP

VIEW BOTTOM

VIEW REAR

TANK MOUNTED (240 GALLON)

60 Hz UNITS

KEY

A Pre filter

B Compressor and cooling air intake

C Starter box

D Cooling air exhaust

E 1.00” NPT air discharge

F Customer power inlet

G Fork lift openings

H Air receiver (240 gallons)

I Automatic drain valve

J 0.25 inch condensate drain

K 4 slots 17 (0.7) x 44 (1.8)

See notes – Page 15

INSTALLATION / HANDLING

15

NOTES

1. Coolant (lubricant) fill quantity (approximate) 3.4 US gallons (13

liters).

2. Recommended clearance in front of control panel door 42 inches

(1067 mm) or minimum as required by the latest national electrical

codes (NEC) or applicable local codes.

3. Recommended clearances on left and right sides 36 inches

(914mm).

4. Minimum recommended clearance for the rear of the compressor

is to be 6 inches (152mm).

5. External piping shall not exert any unresolved moments or forces

on the unit. Use pipe size as large or larger at discharge connection.

6. There should be no plastic or pvc piping attached to this unit or used

for any lines downstream.

7. Any field installed ducting to and from the compressor cannot add

more than 1/2” (12.5mm) water gauge total air resistance.

8. Do not pipe into a common header with a reciprocating compressor,

unless the reciprocating compressor utilizes a discharge pulsation

damper.

9. Sizing of electrical components not supplied by Ingersoll Rand is the

responsibility of the customer and should be done in accordance with

the information on the compressor data plate and national and local

electrical codes.

NOTE

All dimensions are in millimeters (inches) unless otherwise stated.

Ensure that the correct fork lift truck slots or marked lifting points are

used whenever the machine is lifted or transported.

UNPACKING

The compressor will normally be delivered with a polythene cover.

If a knife has to be used to remove this cover ensure that the exterior

paintwork of the compressor is not damaged.

Ensure that all transport and packing materials are discarded in a

manner prescribed by local codes.

NOTE

Units are shipped with transit locking bolt in place. Prior to running

the unit the shipping bolt must be removed and the belt tension

checked. Loosen, remove and discard 10mm shipping bolt. For belt

tensioning procedure refer to Maintenance section.

INSTALLATION / HANDLING

16

KEY

1. Compressor

2. Air Receiver

3. Air Dryer

4. Compressed air filters

5. System demand points

NOTE

Items [2] to [5] are optional or may be existing items of plant. Refer

to your Ingersoll Rand distributor / representative for specific

recommendations.

LOCATION IN THE PLANT

The compressor can be installed on any level floor capable of

supporting it. A dry, well ventilated area where the atmosphere is clean

is recommended. A minimum of 150mm (6 inches) should be left at the

rear and 1m (3ft) at the sides of the machine for adequate service

access and ventilation.

Adequate clearance needs to be allowed around and above the

machine to permit safe access for specified maintenance tasks.

Ensure that the machine is positioned securely and on a stable

foundation. Any risk of movement should be removed by suitable

means, especially to avoid strain on any rigid discharge piping.

CAUTION

Screw type compressors [1] should not be installed in air

systems with reciprocating compressors without means of

isolation such as a common receiver tank. It is recommended that

both types of compressor be piped to a common receiver using

individual air lines.

CAUTION

The use of plastic bowls on line filters and other plastic air line

components can be hazardous. Their safety can be affected by

either synthetic coolants or the additives used in mineral oils.

Ingersoll Rand recommends that only filters with metal bowls

should be used on any pressurised system.

CAUTION

Before starting machine remove shipping bolt and discard.

CAUTION

The standard compressor unit is not suitable for operation in

temperatures liable to cause freezing as Condensate water is

liable to be produced in the after cooler and receiver where fitted.

Refer to your Ingersoll Rand distributor for further information.

DISCHARGE PIPING

Discharge piping should be at least as large as the discharge

connection of the compressor. All piping and fittings should be suitably

rated for the discharge pressure.

It is essential when installing a new compressor [1], to review the

total air system. This is to ensure a safe and effective total system. One

item which should be considered is liquid carryover. Installation of air

dryers [3] is always good practice since properly selected and installed

they can reduce any liquid carryover to zero.

It is good practice to locate an isolation valve close to the

compressor and to install line filters [4].

INSTALLATION / HANDLING

17

60Hz UP6 15 UP6 20 UP6 25 UP6 30

COMPRESSOR 125 150 125 150 200 125 150 200 125 150 200

Maximum operating pressure

PSIG (bar)

125

(8.62)

150

(10.34)

125

(8.62)

150

(10.34)

200

(13.79)

125

(8.62)

150

(10.34)

200

(13.79)

125

(8.62)

150

(10.34)

200

(13.79)

Factory set reload pressure

PSIG (bar)

115

(7.93)

140

(9.66)

115

(7.93)

140

(9.66)

190

(13.10)

115

(7.93)

140

(9.66)

190

(13.10)

115

(7.93)

140

(9.66)

190

(13.10)

Flow rate

CFM (m

3

/MIN)

65

(1.84)

58

(1.64)

83

(2.35)

75

(2.12)

58

(1.64)

102

(2.89)

92

(2.61)

75

(2.12)

125

(3.54)

112

(3.17)

92

(2.61)

Airend discharge temperature

trip point

228_F (109_C)

Ambient operating

temperature

min. omax.

35_F(+2_C ) o 104_F(+40_C)

MOTOR

Motor enclosure ODP TEFC ODP TEFC ODP TEFC ODP TEFC

Nominal power 15HP 20HP 25HP 30HP

Speed 1765 RPM 1770 RPM 1765 RPM 1770 RPM 1765 RPM 1770 RPM 1765 RPM 1770 RPM

Frame 254TZ 160 M 256TZ 160 L 284TZ 180 M 286TZ 180 L

Insulation class F

COOLING SYSTEM

Air cooled

Cooling air flow 1770 ft

3

/min 1770 ft

3

/min 2100 ft

3

/min 2100 ft

3

/min

Maximum 'P in air ducts 0.5 inWg (12.7mmH

2

O)

Compressed air outlet 'T 13_F (7.2_C)

26_F (14_C) 19_F (10_C) 26_F (14_C)

Cooling air outlet 'T 24_F (13.5_C)

27_F (15_C) 29_F (16_C) 35_F (20_C)

GENERAL DATA

Residual coolant content 3ppm (3 mg/m

3

)

Separator vessel capacity 4.5 gallons (17 liters)

Coolant capacity 3.4 gallons (13 liters)

Sound pressure level to

CAGI–PNEUROP

68 dB(A) 68 dB(A) 69 dB(A) 69 dB(A)

Weight – base mount unit 1142lbs (518 kg) 1186 lbs (538 kg) 1206 lbs (547 kg) 1292 lbs (586 kg)

Weight – 120 gallon Receiver

mounted

1466 lbs (665 kg) 1510 lbs (685 kg) 1530 lbs (694 kg) 1616 lbs (733 kg)

Weight – 240 gallon Receiver

mounted

1735 lbs (787 kg) 1779 lbs (807 kg) 1799 lbs (816 kg) 1885 lbs (855 kg)

CAUTION

230/460 Dual voltage machines are fitted with a decal to advise the

correct voltage as connected from the factory.

There is a decal fitted to the starter door describing the procedure

to change the connections for the alternative voltage

Rewiring should only be effected by a competent Electrician.

INSTALLATION / HANDLING

18

60Hz UP6 15–HA UP6 20–HA UP6 25–HA

COMPRESSOR 125 150 200 125 150 200 125 150 200

Maximum operating pressure

PSIG (bar)

125

(8.62)

150

(10.34)

200

(13.79)

125

(8.62)

150

(10.34)

200

(13.79)

125

(8.62)

150

(10.34)

200

(13.79)

Factory set reload pressure

PSIG (bar)

115

(7.93)

140

(9.66)

190

(13.10)

115

(7.93)

140

(9.66)

190

(13.10)

115

(7.93)

140

(9.66)

190

(13.10)

Flow rate

CFM (m

3

/MIN)

65.4

(1.84)

58

(1.64)

45

(1.28)

83

(2.35)

75

(2.12)

58

(1.64)

102

(2.89)

92

(2.61)

75

(2.12)

Airend discharge temperature

trip point

228_F (109_C)

Ambient operating

temperature

min. omax.

35_F(+2_C ) o 122_F(+50_C)

MOTOR

Motor enclosure ODP TEFC ODP TEFC ODP TEFC

Nominal power 15HP 20HP 25HP

Speed 1765 RPM 1770 RPM 1765 RPM 1770 RPM 1765 RPM 1770 RPM

Frame 256TZ 160 L 284TZ 180 M 286TZ 180 L

Insulation class F

COOLING SYSTEM

Air cooled

Cooling air flow 1770 ft

3

/min 2100 ft

3

/min 2100 ft

3

/min

Maximum 'P in air ducts 0.5 inWg (12.7mmH

2

O)

Compressed air outlet 'T

22_F (12_C) 24_F (13_C) 19_F (10_C)

Cooling air outlet 'T

21_F (12_C) 26_F (14_C) 29_F (16_C)

GENERAL DATA

Residual coolant content 3ppm (3 mg/m

3

)

Separator vessel capacity 4.5 gallons (17 liters)

Coolant capacity 3.4 gallons (13 liters)

Sound pressure level to

CAGI–PNEUROP

68 dB(A) 69 dB(A) 69 dB(A)

Weight – base mount unit 1186 lbs (538 kg) 1206 lbs (547 kg) 1292 lbs (586 kg)

Weight – 120 gallon Receiver

mounted

1510 lbs (685 kg) 1530 lbs (694 kg) 1616 lbs (733 kg)

Weight – 240 gallon Receiver

mounted

1779 lbs (807 kg) 1799 lbs (816 kg) 1885 lbs (855 kg)

CAUTION

230/460 Dual voltage machines are fitted with a decal to advise the

correct voltage as connected from the factory.

There is a decal fitted to the starter door describing the procedure

to change the connections for the alternative voltage

Rewiring should only be effected by a competent Electrician.

La page charge ...

Ingersoll-Rand UP6 25 Operation and Maintenance Manual

Ce manuel convient également à

Ingersoll-Rand UP6 25 Operation and Maintenance Manual

dans d''autres langues

Documents connexes

Autres documents