ProTemp PT-24O-DDF User's Manual And Operating Instructions

User’s Manual and

Operating Instructions

Please note the serial number of your fan, and write it on the back of this User’s Manual for future reference.

950451001-14

668 Stony Hill Road #302 Yardley, PA 19067 USA Toll Free: (800) 641-6996

Fax: (215) 891-8461 • Web: www.protemp.us • Email: [email protected]

This product meets and exceeds the requirements of OSHA 1910.212(a)(5), the standard which

regulates electric fan blade safety.

READ AND SAVE THESE INSTRUCTIONS

IMPORTANT: Read and understand all of the instructions in this manual before assembling,

starting, or servicing the fan. Improper use of this fan can cause serious injury. Keep this manual for

future reference.

For General Ventilating Use Only. Do Not Use To Exhaust Hazardous Or Explosive

Materials And Vapors. Never use the fan in spaces which contain products such as

gasoline, solvents, paint thinners, dust particles, volatile or airborne combustibles, or any unknown

chemicals.

CAUTION

'

(

7

6

,

/

&0

Model Numbers: PT-18W-DDF-A, PT-20F-DDF-B,

PT-20S-DDF, PT-24O-DDF, PT-24-DDF-B,

PT-30-DDF-B, PT-30P-DDF-B

User’s Manual and

Operating Instructions

Table of Contents

Safety Information................................................................................................................................. 3

Notes Page............................................................................................................................................4

Troubleshooting Guide........................................................................................................................19

Warranty................................................................................................................................Back Cover

5

18” Wall Fan

PT-18W-DDF-A

6-7

20” Floor Fan

PT-20F-DDF-B

8-10

20” Shop Fan

PT-20S-DDF

11

24” Barrel Fan

PT-24-DDF-B

12-13

24” Omni Fan

PT-24O-DDF

14-16

30” Floor Fan

PT-30-DDF-B

17-18

30” Pedestal Fan

PT-30P-DDF-B

'

(

7

6

,

/

&0

86&

'

(

7

6

,

/

&0

86&

'

(

7

6

,

/

&0

86&

'

(

7

6

,

/

&0

86&

NEVER LEAVE A FAN

UNATTENDED WHILE

OPERATING OR WHILE

CONNECTED TO A POWER

SOURCE

Safety Information

- Before operating always check fan for loose

or damaged parts. Inspect power cord for any

damage. Never use fan if any parts are

damaged or missing. Never use fan without

safety guards attached.

- Operate only on 120 volt 60 Hz (cycle) current

with a minimum of a 15 amp circuit.

- When used with an extension cord, use only

cord of proper size (Amp rating), UL listed, and

with receptacle to accept three prong grounded

plug furnished on the fan’s power cord. Always

keep power cord and extension cords away

from heat, oil, and sharp edges. Inspect cords

periodically and replace if damaged.

IMPORTANT: READ ALL INSTRUCTIONS CAREFULLY BEFORE ASSEMBLY, SERVICE OR

USE OF THIS FAN. FAILURE TO COMPLY WITH THESE INSTRUCTIONS COULD RESULT IN

SERIOUS PERSONAL INJURY AND / OR PROPERTY DAMAGE.

THIS IS A FAN - NOT A TOY!

TO REDUCE THE RISK OF

PERSONAL INJURY AND ELECTRIC SHOCK,

FANS SHOULD NOT BE PLAYED WITH OR

PLACED WHERE SMALL CHILDREN CAN

REACH IT.

WARNING

To guard against electric shock

while operating, do not allow fan

to come in contact with other grounded objects

such as pipes, radiators, etc.

WARNING

Risk of fire, electric shock, or

personal injury when performing

service or maintenance. Unplug or disconnect

the fan from the power supply before servicing.

WARNING

CAUTION Automatically

Operated Device - To Reduce

The Risk Of Injury Disconnect From Power

Source Before Servicing

WARNING

To Reduce The Risk Of Fire

Or Electric Shock, Do Not Use

This Fan With Any Solid- State Speed Control

Device.

WARNING

To Reduce The Risk Of Electric

Shock And Injury To Persons, Do

Not Use In a Window.

WARNING

To Reduce The Risk Of Electric

Shock, Do Not Expose To Water

Or Rain. This unit is designed for indoor use

only.

WARNING

Installation work and electrical

wiring must be done by

qualified person (s) in accordance with all

applicable codes and regulations.

WARNING

When servicing or replacing a

component requires the removal

or disconnection of a safety device, the safety

device is to be reinstalled or remounted as

previously installed before operating this fan.

WARNING

Use this fan only in the manner

intended by the manufacturer.

If you have any questions, contact Customer

Service at 800-641-6996.

WARNING

NEVER LEAVE A FAN

UNATTENDED WHILE

OPERATING OR WHILE

CONNECTED TO A POWER

SOURCE

NOTES

__________________________________________________________________________________________

NEVER LEAVE A FAN

UNATTENDED WHILE

OPERATING OR WHILE

CONNECTED TO A POWER

SOURCE

Replacement Parts

Item # Description Part Number

1 Logo Plate 95-043-0370

2 Front Guard 95-032-0150

3

Fan Blade Assembly 95-003-06064

5

6 Upper Bracket 95-061-0100

7 Rear Guard 95-032-0250

8 Motor 95-030-0515

9 Switch Holder 95-031-0300

Item # Description Part Number

10 Switch Gasket 95-031-0340

11 Switch (Chain) 95-031-0110

12 Switch Cover 95-031-0500

13 Cord Bushing 95-026-0160

14 Pivot Washer 95-024-0300

15 Swivel Spacer 95-050-0185

16 Pivot Screw 95-024-0310

17 Capacitor 95-004-0215

18 Power Cord 95-026-0230

18” WALL FAN: PT-18W-DDF-A

1

2

3

4

5

6 7

8

9

10 11

12

13

14

15

16

17

18

Figure 1: Exploded View of PT-18W-DDF-A

Exploded View

Wall Mount Installation

1. Attach fan to wall or ceiling using Upper Bracket

(Item #6).

2. Be sure Upper Bracket (Item #6) is attached to a

suitable beam when hanging.

Tools Needed:

- 10mm Adjustable Wrench.

The installer MUST be

certain that the support bracket is

mounted to a minimum of a 2x4” stud, and that it

is able to support 50 pounds continuously.

WARNING

1. Attach wall mount to stud (Item #24*)

2. Attach Lower Support Frame (Item #21*) to the Wall

Mount (Item #24*) by replacing rear part of Lower

Support Frame into hook of Wall Mount and resting

front and rear feet of fan (Items #17* and #18*) onto

the wall.

* On Page 7

NOTE: Fan must be mounted to wall so that both feet

are positioned against the wall surface. Mounting

this fan to a bare stud without both fan feet posi-

tioned against a flat surface will result in damage

to the fan.

NEVER LEAVE A FAN

UNATTENDED WHILE

OPERATING OR WHILE

CONNECTED TO A POWER

SOURCE

1. Place the fan on level ground in a safe,

desired position then connect to an approved

power source.

20” FLOOR FAN: PT-20F-DDF-B

Installation

The installer MUST be

certain that the support bracket is

mounted to a minimum of a 2x4”

stud, and that it is able to support 50 pounds

continuously.

WARNING

20” FLOOR FAN - OPTIONAL WALL MOUNT

Wall Mount Installation

Figure 2: Wall Mount Installation

Figure 3: Wall Mount Installation - Close Up

24

21

17

18

NEVER LEAVE A FAN

UNATTENDED WHILE

OPERATING OR WHILE

CONNECTED TO A POWER

SOURCE

Replacement Parts

Item # Description Part Number

1 Front Guard 95-032-2000

2 Fan Blade Assembly 95-003-2005

3 Rear Guard 95-032-2001

4 Power Switch 95-031-2000

5 Motor 95-030-2000

6 Adjustment Knob 95-015-2000

7 Fan Frame 95-009-2000

8 Plastic Spacer 95-015-2000

9 Adjustment Bolt 95-015-2001

N/A Power Cord 95-026-2000

20” FLOOR FAN CONTINUED

1

2

3

4

5

6

7

8

9

Exploded View

Figure 4: Exploded View of PT-20F-DDF-B

NEVER LEAVE A FAN

UNATTENDED WHILE

OPERATING OR WHILE

CONNECTED TO A POWER

SOURCE

20” SHOP FAN: PT-20S-DDF

Installation and Assembly

1. Remove Knob Screw (Item #15*) and Wing Nut (Item

#14*) from top of Post.

2. Slide Connector Bracket (Item #4*) onto top of post.

3. Line up holes on the Post and Connector Bracket

(Item #4*).

4. Re-insert the Knob Screw (Item #15) through the Post

and Connector Bracket (Item #14*) and tighten firmly

with the Wing Nut (Item #14*).

5. Place the fan on level ground in a safe, desired position

then connect to an approved power source.

6. Set desired tripod stand height following “Tripod

Operation Instructions” below.

* On Page 10

Tripod Operation Instructions

TRIPOD LEG OPERATION

1. Fold legs out and slide support bracket to center of leg.

2. To adjust leg height; rotate locking ring clockwise to

loosen.

NOTE: Keep a firm grip on the tripod while leg is

unlocked! The leg will collapse into itself unless

held tightly.

NOTE: Be certain to make all three legs the same

height. Setting legs to different heights will make

the fan unbalanced and COULD FALL OVER.

3. Slide leg extension to desired height.

4. Rotate locking ring counter-clockwise and tighten firmly.

Be sure the leg is secure before moving to next leg.

5. Repeat steps 2-4 for remaining legs.

TRIPOD CENTER POST OPERATION

1. To change the post height; rotate locking ring

counter-clockwise to unlock post.

NOTE: Be certain to keep a firm grip on post while

unlocked! The fan will slide down to its lowest

point if it is not held and slowly moved to desired

position.

2. Raise or lower post to desired position.

3. Rotate locking ring clockwise to lock post and tighten

firmly.

DO NOT MOVE OR ADJUST

FAN WHILE IN OPERATION.

THIS CAN CAUSE DAMAGE TO FAN AND

INJURY TO THE OPERATOR.

WARNING

OPTIONAL CEILING MOUNT

1. Attach Ceiling Mounting Kit (Item #16*) to 2x4” stud

that is able to support 50 lbs continuously using

M6x40mm screw. (See Figure 5**)

3. Be Certain that the Safety Pin lines up with the groove

on the Frame (Item #4). (See Figure 6**)

2. Slide Connector Bracket (Item #4*) onto Ceiling

Mounting Post. (See Figure 7**)

4. Rotate the entire fan so the safety pin locks into place

and the holes on the Mounting Post line up with the

holes on the Connector Bracket (Item #4*). (See Figure

8**)

5. Insert the Knob Screw (Item #15*) through the

Mounting Post and Connector Bracket (Item #4*) and

tighten firmly with the Wing Nut (Item #14*).

(See Figure 8**)

* On Page 10

** On Page 9

Installation and Assembly

The installer MUST be

certain that the support bracket is

mounted to a minimum of a 2x4”

stud, and that it is able to support 50 pounds

continuously.

WARNING

NEVER LEAVE A FAN

UNATTENDED WHILE

OPERATING OR WHILE

CONNECTED TO A POWER

SOURCE

20” SHOP FAN CONTINUED - OPTIONAL CEILING MOUNT

Figure 5:

Optional Ceiling Mount

Figure 8:

Optional Ceiling Mount

Figure 7:

Optional Ceiling Mount

Figure 6:

Optional Ceiling Mount

NEVER LEAVE A FAN

UNATTENDED WHILE

OPERATING OR WHILE

CONNECTED TO A POWER

SOURCE

20” SHOP FAN CONTINUED

Exploded View

Replacement Parts

Item # Description Part Number

1 Logo Plate 95-043-0420

2 Front Guard 95-032-0185

3 Fan Blade Assembly 95-003-0616

4 Frame 95-001-0500

5 Rear Guard 95-032-0285

6 Motor 95-030-0525

7 Switch Holder 95-031-0335

8 Power Cord 95-026-0270

Item # Description Part Number

9 Power Switch 95-025-0600

10 Capacitor 95-004-0250

11 Bushing 95-026-0180

12 Switch Cover 95-031-0540

13 Tripod 95-040-0100

14 Wing Nut 95-075-0400

15 Base Knob 95-015-0220

16 Ceiling Mount Kit 95-078-0300

123

4

567 8 91011

121514

13

Figure 9: Exploded View of PT-20S-DDF

16

1

2

3

10

8

7

9

6

5

4

11

12

NEVER LEAVE A FAN

UNATTENDED WHILE

OPERATING OR WHILE

CONNECTED TO A POWER

SOURCE

24” BARREL FAN: PT-24-DDF-B

Installation and Assembly

1. Place the fan on level ground in a safe, desired

position then connect to an approved power source.

NOTE: This model CAN NOT be wall mounted.

Replacement Parts

Exploded View

Figure 10: Exploded View of

PT-24-DDF-B

Item # Description Part Number

1 Safety Guard - Front / Rear 95-032-2020

2 Fan Blade Assembly 95-003-2021

3 Motor 95-030-2020

4 Power Cord 95-026-2020

5 Power Switch 95-031-2020

6 Barrel 95-001-2000

7 Handle 95-006-2020

8 Knob Screw 95-015-2020

9 Rubber Spacer 95-015-2021

10 Fan Frame 95-009-2020

11 Wheel 95-008-2010

12 Cotter Pin 95-008-2011

NEVER LEAVE A FAN

UNATTENDED WHILE

OPERATING OR WHILE

CONNECTED TO A POWER

SOURCE

24’’ OMNI DIRECTIONAL FAN: PT-24O-DDF

Replacement Parts

Item # Description Part Number

1 Front Guard 95-032-0170

2 Fan Barrel 95-001-0400

3 Power Knob 95-027-0130

4 Power Knob Holder 95-031-0325

5 Capacitor 95-004-0235

6 Power Cord 95-026-0255

7 Motor 95-030-0535

8 Motor Mount Assembly 95-030-0555

9 Motor Cooling Fan 95-030-0556

10 Fan Blade Assembly 95-003-0621

11 Rear Guard 95-032-0275

12 Front Leg 95-009-0600

13 Horizontal Adj. Knob 95-015-0150

14 Spacer 95-050-0200

15 Outer Ring Frame 95-024-0320

Item # Description Part Number

16 Vertical Adj. Knob 95-015-0150

17 Wall Mount 95-078-0200

18 Handle Pad 95-007-0100

19 Spacer 95-050-0200

20 Handle Arm 95-006-0300

21 Rear Leg 95-009-0610

22 Large Base Cap 95-024-0410

23 Large Base 95-024-0400

24 Foot Pad 95-023-0240

25 Wall Bracket - L 95-077-0100

26 Wall Bracket - R 95-077-0110

27 Small Base 95-024-0500

28 Small Base Cap 95-024-0510

29 Wheel 95-004-0155

30 Lower Mount 95-024-0325

31 Logo Plate 95-043-0331

Exploded View

1

2

3

4

5

7

8

9

10

11

12

13

14

16

19

17

18

21

20

22

23

25

26

27

Figure 11: Exploded View of: PT-24O-DDF

28

24

29

30

15

6

31

Installation and Assembly

1. Place the fan on level ground in a safe, desired position

then connect to an approved power source.

NEVER LEAVE A FAN

UNATTENDED WHILE

OPERATING OR WHILE

CONNECTED TO A POWER

SOURCE

24” OMNI FAN - OPTIONAL WALL MOUNT

1. Attach Wall Mount (Item #17* in Figure 12) to wood

stud as shown below.

2. Slide Wall Bracket L (Item #25*) and Wall Bracket

R (Item #26*) on Large Base (Item #23*) onto Wall

Mount. (Figure 13)

* Figure 12

Tools Needed

-Flat head Screw Driver.

Wall Mount Installation

The installer MUST be

certain that the support bracket is

mounted to a minimum of a 2x4” stud, and that it

is able to support 105 pounds continuously.

WARNING

2”x4”

STUD

Wall

Wall Mount (Item #17*)

Handle Arm (Item #20*)

Wall Mount

(Item #17*)

Large Base

(Item #23*)

Figure 13: Wall Mount installation

Figure 12: Wall Mount installation Close Up

NEVER LEAVE A FAN

UNATTENDED WHILE

OPERATING OR WHILE

CONNECTED TO A POWER

SOURCE

30” FLOOR FAN: PT-30-DDF-B

Replacement Parts

Item# Description Part Number

1 Front Guard 95-032-2010

2 Fan Blade Assembly 95-003-2015

3 Motor 95-030-2010

4 Knob Screw 95-015-2010

5 Rubber Spacer 95-015-2011

6 Wheel 95-008-2000

7 Fan Frame 95-009-2010

8 Handle 95-006-2000

9 Rear Guard 95-032-2011

N/A Power Switch 95-031-2010

N/A Power Cord 95-026-2010

Installation and Assembly

1. Place the fan on level ground in a safe, desired position

then connect to an approved power source.

NOTE: This fan uses a folding wheel design. For quick

assembly, simply swing the wheels out and snap to

lock in place.

1

2

3

4

5

6

7

8

9

Exploded View

Figure 14: Exploded View of PT-30-DDF-B

This 30” Floor Fan (PT-30-DDF-B) is approved for

use with California’s BAR-97 Emissions Inspection

System and meets all BAR-97(EIS) required

specications and standards

Installation and Assembly

Tools Needed:

Pliers

Phillips head screwdriver

Flat head screwdriver

10mm / adjustable wrench

Parts Included In Box:

(1) Base

(1) Front Guard

(1) Rear Guard

(1) Motor Assembly

(1) Fan Blade Assembly

(1) Locking Collar

(1) Upper Support Pole

(1) Lower Support Pole

1. Place the base on level ground

2. Mount the support pole to the base. Make

sure the holes line up.

3. Secure tightly with 5 flange screws using the

wrench.

4. Put down the base cover.

5. Loosen the locking collar screw using the

Allen wrench (hex wrench). Extract the upper

support pole slowly to adjust the height of the

fan.

6. Mount the motor assembly to the connector

on the upper support pole. Make sure the

holes line up

7. Secure motor assembly with Bolt (M12*40)

and Nut (M12). Tighten the bolt firmly using

the wrench.

8. Slide the rear guard on to motor assembly

and secure it with 4 flange screws. Tighten

the screws firmly using the wrench.

9. Loosen the screw on the back of the fan

blade assembly using the Allen wrench (Hex

Wrench). Slide the fan blade assembly onto

the motor shaft.

10. Attach the front guard to the back guard and

secure with the fasteners on the front guard.

NOTE: This model CAN NOT be wall mounted

30” PEDESTAL FAN: PT-30P-DDF-B

NEVER LEAVE A FAN

UNATTENDED WHILE

OPERATING OR WHILE

CONNECTED TO A POWER

SOURCE

Figure 19: Attaching Rear Guard to Motor

Rear Guard

Motor

Motor Assembly

Pivot Bolt

Nut

Upper Support Pole

Figure 18: Attaching Motor to Motor Support Assembly

Do NOT slide fan blade screw

beyond the groove on the shaft!

This will cause the fan blade to not spin properly

and can cause damage to your fan! Be sure that fan

shaft is flush with front of fan blade assembly.

CAUTION

30” PEDESTAL FAN

NEVER LEAVE A FAN

UNATTENDED WHILE

OPERATING OR WHILE

CONNECTED TO A POWER

SOURCE

Replacement Parts

Figure 20: Exploded View of

PT-30P-DDF-B

Exploded View

Item # Description Part Number

1 Front Guard 95-032-2030

2 Fan Blade Assembly 95-003-2030

3 Rear Guard 95-032-2035

4 Motor 95-030-2030

5 Upper Pole Connector 95-017-2000

6 Motor Mount Bracket 95-017-2005

7 Power Cord 95-026-2030

Item # Description Part Number

8 Upper Support Pole 95-017-2020

9 Locking Collar 95-017-2030

10 Base Cover 95-024-2005

11 Lower Support Pole 95-017-2025

12 Base 95-024-2000

13 Power Switch 95-031-2030

Troubleshooting Guide

Problem Possible Cause Corrective Action

Fan does not operate

1. No power

Inspect power cord for damage. Be sure unit is

plugged in and turned on.

2. Bad motor Replace motor

Reduced Air Flow

1. Obstruction

Turn off and unplug fan. Remove guard and make sure

nothing is obstructing the fan blades.

2. Bad switch or capacitor

Replace switch or capacitor (Note: To prolong life of

fan, operate fan first in 1(LOW) for 5-10 seconds before

switching to higher speed.

Humming sound but no

operation

1. Bad capacitor Replace capacitor

Excess Noise (vibration,

squealing)

1. Fan is not on level ground Turn off fan, and move unit to smooth level surface.

2. Guard is not secure Check guard screws to be sure all are tight.

NEVER LEAVE A FAN

UNATTENDED WHILE

OPERATING OR WHILE

CONNECTED TO A POWER

SOURCE

1 YEAR LIMITED WARRANTY

PINNACLE PRODUCTS INTERNATIONAL, INC. WARRANTS THIS

PRODUCT TO THE ORIGINAL RETAIL PURCHASER ONLY, TO BE

FREE FROM DEFECTS IN MATERIAL AND WORKMANSHIP FOR

A PERIOD OF ONE (1) YEAR FROM THE DATE OF INITIAL PUR-

CHASE. THIS PRODUCT MUST BE PROPERLY INSTALLED, MAIN-

TAINED AND OPERATED IN ACCORDANCE WITH THE INSTRUC-

TIONS PROVIDED.

PINNACLE PRODUCTS INTERNATIONAL, INC. REQUIRES REA-

SONABLE PROOF OF YOUR DATE OF PURCHASE FROM AN

AUTHORIZED RETAILER OR DISTRIBUTOR. THEREFORE, YOU

SHOULD KEEP YOUR SALES SLIP, INVOICE, OR

CANCELLED CHECK FROM THE ORIGINAL PURCHASE. THIS

LIMITED WARRANTY SHALL BE LIMITED TO THE REPAIR OR

REPLACEMENT OF PARTS, WHICH PROVE DEFECTIVE UNDER

NORMAL USE AND SERVICE WITHIN THE

WARRANTY PERIOD, AND WHICH PINNACLE PRODUCTS

INTERNATIONAL, INC. SHALL DETERMINE AT ITS

REASONABLE DISCRETION.

THIS WARRANTY DOES NOT APPLY TO PRODUCTS

PURCHASED FOR RENTAL USE.

THIS LIMITED WARRANTY DOES NOT COVER REPLACEMENT OF

BELTS OR TIGHTENING OF BELTS, OR ANY

FAILURES OR OPERATING DIFFICULTIES DUE TO NORMAL

WEAR AND TEAR, ACCIDENT, ABUSE, MISUSE, ALTERATION,

MISAPPLICATION, IMPROPER INSTALLATION OR IMPROPER

MAINTENANCE AND SERVICE BY YOU OR ANY THIRD PARTY.

FAILURE TO PERFORM NORMAL AND ROUTINE MAINTENANCE

ON THE FAN, SHIPPING DAMAGE, DAMAGE RELATED TO

INSECTS, BIRDS, OR ANIMALS OF ANY KIND, AND DAMAGE DUE

TO WEATHER CONDITIONS ARE ALSO NOT COVERED. IN ADDI-

TION, THE LIMITED WARRANTY DOES NOT COVER DAMAGE TO

THE FINISH, SUCH AS SCRATCHES, DENTS, DISCOLORATION,

RUST OR OTHER WEATHER DAMAGE, AFTER PURCHASE.

ALL TRANSPORTATION COSTS FOR THE RETURN OF THE DAM-

AGED PRODUCT OR PARTS WILL BE THE

RESPONSIBILITY OF THE PURCHASER. UPON RECEIPT OF DAM-

AGED ITEM, PINNACLE PRODUCTS INTERNATIONAL, INC. WILL

EXAMINE THE ITEM AND DETERMINE IF

DEFECTIVE.

PINNACLE PRODUCTS INTERNATIONAL, INC. WILL REPAIR

OR REPLACE AND RETURN THE ITEM, FREIGHT PRE-PAID. IF

PINNACLE PRODUCTS INTERNATIONAL, INC. FINDS THE ITEM

TO BE IN NORMAL OPERATING CONDITION, OR NOT DEFEC-

TIVE, THE ITEM WILL BE RETURNED FREIGHT

COLLECT.

THIS LIMITED WARRANTY IS IN LIEU OF ALL OTHER EXPRESS

WARRANTIES. PINNACLE PRODUCTS INTERNATIONAL, INC.

DISCLAIMS ALL WARRANTIES FOR PRODUCTS THAT ARE PUR-

CHASED FROM SELLERS OTHER THAN AUTHORIZED RETAIL-

ERS OR DISTRIBUTORS.

AFTER THE PERIOD OF THE ONE (1) YEAR LIMITED

WARRANTY EXPIRES, PINNACLE PRODUCTS INTERNATIONAL,

INC. DISCLAIMS ANY AND ALL IMPLIED WARRANTIES,

INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES

OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

APPLICATION. FURTHER, PINNACLE PRODUCTS

INTERNATIONAL, INC. SHALL HAVE NO

LIABILITY WHATSOEVER TO PURCHASER OR ANY THIRD PARTY

FOR ANY SPECIAL, INDIRECT, PUNITIVE,

INCIDENTAL, OR CONSEQUENTIAL DAMAGES. PINNACLE

PRODUCTS INTERNATIONAL, INC. ASSUMES NO

RESPONSIBILITY FOR ANY DEFECTS CAUSED BY THIRD PAR-

TIES. THIS LIMITED WARRANTY GIVES THE

PURCHASER SPECIFIC LEGAL RIGHTS; A PURCHASER MAY

HAVE OTHER RIGHTS DEPENDING UPON WHERE HE OR SHE

LIVES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMI-

TATION OF SPECIAL, INCIDENTAL OR

CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON HOW LONG

A WARRANTY LASTS, SO THE ABOVE EXCLUSION AND LIMITA-

TIONS MAY NOT APPLY TO YOU.

PINNACLE PRODUCTS INTERNATIONAL, INC. DOES NOT

AUTHORIZE ANY PERSON OR COMPANY TO ASSUME FOR

IT ANY OTHER OBLIGATION OR LIABILITY IN CONNECTION

WITH THE SALE, INSTALLATION, USE, REMOVAL, RETURN,

OR REPLACEMENT OF ITS EQUIPMENT, AND NO SUCH REP-

RESENTATIONS ARE BINDING ON PINNACLE PRODUCTS

INTERNATIONAL, INC.

ALWAYS BE SURE TO SPECIFY MODEL NUMBER AND SERIAL NUMBER WHEN MAKING ANY CLAIM

WITH PINNACLE PRODUCTS INTERNATIONAL, INC. FOR YOUR CONVENIENCE USE THE SPACE

PROVIDED BELOW TO LIST THIS INFORMATION:

Model #: ____________________ Serial #: ______________________

Date of Purchase: _________________

NEVER LEAVE A FAN

UNATTENDED WHILE

OPERATING OR WHILE

CONNECTED TO A POWER

SOURCE

668 Stony Hill Road #302 Yardley, PA 19067 USA Toll Free: (800) 641-6996

Fax: (215) 891-8461 • Web: www.protemp.us • Email: [email protected]

Register Online at: www.protemp.us/Product_Registration.php

NEVER LEAVE A FAN

UNATTENDED WHILE

OPERATING OR WHILE

CONNECTED TO A POWER

SOURCE

NOTES

__________________________________________________________________________________________

NEVER LEAVE A FAN

UNATTENDED WHILE

OPERATING OR WHILE

CONNECTED TO A POWER

SOURCE

NOTES

__________________________________________________________________________________________

La page charge ...

ProTemp PT-24O-DDF User's Manual And Operating Instructions

Ce manuel convient également à

ProTemp PT-24O-DDF User's Manual And Operating Instructions

dans d''autres langues

Documents connexes

Autres documents