Frigidaire Gallery GRSC2352AD Mode d'emploi

Frigidaire.com USA 1-800-374-4432 Frigidaire.ca Canada 1-800-265-8352

use

&

care

REFRIGERATOR

A19894604 (November 2020)

Introduction .......................................................2

Important Safety Information ....................3

Features ............................................................6

Installation .........................................................7

Door Removal ................................................10

Door Handle Installation ............................. 12

Water Supply Connection .......................... 13

Controls and Settings ................................. 15

Automatic Ice and Water Dispenser ...... 19

Storage Features ........................................... 21

Normal Operating Sounds ........................ 22

Filter Replacement ...................................... 23

Care and Cleaning ....................................... 25

Troubleshooting .......................................... 29

Limited Warranty ......................................... 33

2

INTRODUCTION

Doors

 Handles are secure and tight

 Door seals completely to cabinet on

all sides

 Doors are level with each other.

Leveling

 Appliance is level side-to-side and

tilted ¼" (6 mm) front-to-back

 Toe grille is properly attached.

 Cabinet is level on the ﬂoor.

Electrical Power

 House power turned on

 Appliance is plugged in

Ice Maker

 House water supply connected

to appliance (Warning: Potable

water supply only.)

 No water leaks present at all

connections - recheck in 24 hours

 Ice maker is turned ON

 Ice & water dispenser

operates correctly

Final Checks

 Shipping material removed

 Refrigerator and freezer tempera-

tures set to recommended setting

 Crisper humidity controls set

(some models)

 Registration card sent in

Installation Checklist



Welcome to our

family

Thank you for bringing Frigidaire into

your home! We see your purchase as the

beginning of a long relationship together.

This manual is your resource for the use

and care of your product. Please read

it before using your appliance. Keep it

handy for quick reference. If something

doesn’t seem right, the troubleshooting

section will help you with common issues.

FAQs, helpful tips and videos, cleaning

products, and kitchen and home accesso-

ries are available at Frigidaire.com.

We are here for you! Visit our website,

chat with an agent, or call us if you need

help. We may be able to help you avoid

a service visit. If you do need service, we

can get that started for you.

Let’s make it ocial! Be sure to register

your product.

Keep your product info here so it’s easy

to ﬁnd.

Model Number ____________________

Serial Number ____________________

Purchase Date ____________________

Lorem ipsum Lorem ipsumLorem i

psumLorem ipsumLorem ipsumLore

m ipsumLorem ipsum

Lorem ipsum Lorem ipsumLorem i

psumLorem ipsumLorem ipsumLore

m ipsumLorem ipsum

Lorem ipsum Lorem ipsumLorem

Serial Number Location

3

WARNING

WARNING indicates a potentially haz-

ardous situation which, if not avoided,

could result in death or serious injury.

IMPORTANT

IMPORTANT indicates installation, oper-

ation or maintenance information which

is important but not hazard-related.

DANGER

DANGER indicates an imminently haz-

ardous situation which, if not avoided,

will result in death or serious injury.

CAUTION

CAUTION indicates a potentially haz-

ardous situation which, if not avoided,

may result in minor or moderate injury.

Safety Deﬁnitions

This is the safety alert symbol. It is

used to alert of potential personal injury

hazards. Obey all safety messages that

follow this symbol to avoid possible injury

or death.

WARNING

Please read all instructions before using

this appliance.

IMPORTANT SAFETY INFORMATION

DANGER

DANGER Risk of ﬁre or explosion.

Flammable refrigerant used. Do not use

mechanical devices to defrost refrigera-

tor. Do not puncture refrigerant tubing.

DANGER Risk of ﬁre or explosion.

Flammable refrigerant used. To be re-

paired only by trained service person-

nel. Use only manufacturer-authorized

service parts. Any repair equipment

used must be designed for ﬂammable

refrigerants. Follow all manufacturer

repair instructions. Do not puncture

refrigerant tubing.

CAUTION

CAUTION Risk of ﬁre or explosion.

Dispose of refrigerator properly

in accordance with the applicable

federal or local regulations. Flammable

refrigerant used.

CAUTION Risk of ﬁre or explosion

due to puncture of refrigerant tubing.

Follow handling instructions carefully.

Flammable refrigerant used.

WARNING

CALIFORNIA RESIDENTS ONLY

Cancer and Reproductive Harm

www.P65Warnings.ca.gov

4

IMPORTANT SAFETY INFORMATION

WARNING

These guidelines must be followed to

ensure that safety mechanisms in this

unit will operate properly.

Proper Disposal of your Appliance

Risk of child entrapment

Child entrapment and suocation are

not problems of the past. Junked or

abandoned appliances are still dangerous

– even if they will sit for “just a few days”.

If you are getting rid of your old unit,

please follow the instructions below to

help prevent accidents.

We strongly encourage responsible appli-

ance recycling/disposal methods. Check

with your utility company or visit

energystar.gov/recycle for more informa-

tion on recycling your old appliance.

Safety Instructions

• DO NOT store or use gasoline, or

other ﬂammable liquids, or aerosols

within or in the vicinity of this or any

other appliance. Read product labels

for warnings regarding ﬂammability

and other hazards.

• DO NOT operate the unit in the

presence of explosive fumes.

• Avoid contact with any moving parts

of automatic ice maker.

• Remove all staples from the carton.

Staples can cause severe cuts, and also

destroy ﬁnishes if they come in contact

with other appliances or furniture.

Child Safety

This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities,

or lack of experience and knowledge,

unless they have been given supervision

or instruction concerning use of the

appliance by a person responsible for

their safety.

Destroy or recycle the carton, plastic

bags, and any exterior wrapping material

immediately after the appliance is

unpacked. Children should never use

these items to play. Cartons covered with

rugs, bedspreads, plastic sheets or stretch

wrap may become airtight chambers, and

can quickly cause suocation.

Before you throw away your appliance:

• Remove doors.

• Leave shelves in

place so children

may not easily

climb inside.

• Have refrigerant

removed by a

qualiﬁed service

technician.

5

Electrical information

• The appliance must be plugged into

its own dedicated 115 Volt, 60 Hz.,

15 Amp, AC only electrical outlet.

The power cord of the appliance

is equipped with a three-prong

grounding plug for your protection

against electrical shock hazards.

It must be plugged directly into a

properly grounded 3-prong recepta-

cle. The receptacle must be installed

in accordance with local codes and

ordinances. Consult a qualiﬁed elec-

trician. Avoid connecting the unit to a

Ground Fault Interrupter (GFI) circuit.

Do not use an extension cord or

adapter plug.

• If the power cord is damaged, it

should be replaced by an authorized

service technician to prevent any risk.

• Never unplug the appliance by pull-

ing on the power cord. Always grip

the plug ﬁrmly, and pull straight out

from the receptacle to prevent dam-

aging the power cord.

• Performance may be aected if the

voltage varies by 10% or more. Oper-

ating the appliance with insucient

power can damage the compressor.

Such damage is not covered under

your warranty.

• Do not plug the unit into an electrical

outlet controlled by a wall switch or

pull cord to prevent the unit from

being turned o accidentally.

Grounding type wall receptacle

Power cord with

3-prong grounded plug

Do not, under

any circumstances,

cut, remove,

or bypass the

grounding prong.

IMPORTANT

CFC/HCFC Disposal

Your old unit may have a cooling system

that used CFCs or HCFCs (chloroﬂuoro-

carbons or hydrochloroﬂuorocarbons).

CFCs and HCFCs are believed to harm

stratospheric ozone if released to the

atmosphere. Other refrigerants may

also cause harm to the environment if

released to the atmosphere.

If you are throwing away your old ap-

pliance, make sure the refrigerant is re-

moved for proper disposal by a qualiﬁed

technician. If you intentionally release

refrigerant, you may be subject to ﬁnes

and imprisonment under provisions of

environmental legislation.

IMPORTANT SAFETY INFORMATION

CAUTION

To avoid personal injury or property

damage, handle tempered glass shelves

carefully. Shelves may break suddenly

if nicked, scratched, or exposed to sud-

den temperature change.

IMPORTANT

Turn o power to your appliance you

must unplug the power cord from the

electrical outlet.

6

A Fixed Door Bins

B Ice Maker

C Ice Container

D Shelves

E Damper/Air Filter Housing

F LED Lights

G Water Filter

H Dairy Compartment

I Temperature Sensor/Thermistor

J Adjustable Door Bins

K Deli Drawer (some models)

L Crisper Drawers

M Toe Grille

N Slide-Out Basket

*Features may vary according to model

L

M

N

B

C

D

E

F G

H

I

J

K

A

F

FEATURES

IMPORTANT

Accessories are available for your appliance and may be purchased at

Frigidaire.com or by calling 1-800-374-4432 (Frigidaire.ca or 1-800-265-8352 in

Canada) or from an authorized seller.

7

INSTALLATION



NOTE

If your unit is placed with the door hinge

side against a wall, you may have to

allow additional space for the handle so

the door can be opened wider.

This Use & Care Manual provides general

operating instructions for your model. Use

the unit only as instructed in this Use &

Care Manual. Before starting the appli-

ance, follow these important ﬁrst steps.

Installation

Installation clearances

• Allow the following clearances for ease

of installation, proper air circulation, and

plumbing and electrical connections:

Sides & Top ⅜"

Back 1"

Location

• Choose a place that is near a ground-

ed electrical outlet. Do Not use an

extension cord or an adapter plug.

• If possible, place the unit out of direct

sunlight and away from the range,

dishwasher or other heat sources.

• Install the appliance on a ﬂoor that is

level and strong enough to support a

fully loaded unit.

• Consider water supply availability for

models equipped with an automat-

ic ice maker. If you do not hook up

water to the appliance, remember to

turn the ice maker o.

CAUTION

Do Not install the unit where the tem-

perature will drop below 55°F (13°C) or

rise above 110°F (43°C). The compres-

sor will not be able to maintain proper

temperatures inside the appliance.

Do Not block the toe grille on the lower

front of your unit. Sucient air circula-

tion is essential for the proper opera-

tion of your appliance.

Toe Grille Installation and Removal

To install toe grille

1. Open both doors. Slide the left and

right sides of the toe grille over the

lower hinges of the appliance.

2. While pushing the toe grille ﬁrmly

against cabinet, fasten the bottom

clips of toe grille to the cabinet.

3. Fasten the top clips to the cabinet.

4. Close the doors. Fasten the right

and left side clips into the groove of

the bottom hinge.

To remove the toe grille

1. With both doors closed, unfasten

the right and left side clips of toe

grille from the bottom hinge groove.

2. Open both doors. Press ﬁrmly on the

top of the toe grille until the top of

the toe grille pops o.

3. Pull the toe grille outward toward

your body and o of the lower hinges.

1

2

3

2

3

1

4

Installing Toe Grille

1

2

3

2

3

1

Removing Toe Grille

WARNING

This appliance is intended to be used

in household and similar applications

such as:

• sta kitchen areas in shops, oces

and other working environments;

• farm houses and by clients in hotels,

motels and other residential type

environments;

• bed and breakfast type

environments;

• catering and similar non-retail

applications.

8

INSTALLATION

Door Opening

Position your unit to allow easy access to

a counter or table when removing food.

For the best use of drawers and freezer

baskets, position the appliance where

both doors can fully open.

Guidelines for ﬁnal positioning

of your unit:

• Rest all 4 corners of the cabinet

ﬁrmly on the ﬂoor.

• Level the cabinet at the front and rear.

• Tilt the sides ¼" (6 mm) from front

to back (to ensure the doors close

and seal properly).

• Align the doors with each other

and level.

Meet all of these conditions by

raising or lowering the adjust-

able front rollers.

To level the cabinet using the front rollers:

1. Open both doors and remove the

toe grille (see “Toe Grille Installation

and Removal” in INSTALLATION).

2. Close the doors and use a wrench

to raise (clockwise) or lower

(counterclockwise) the front rollers.

3. Ensure both doors are bind-free with

their seals touching the cabinet on all

4 sides.



NOTE

The doors are designed to shut by

themselves within a 20 degree opening.

9

Set Screw

(some models)

Hinge

Flange

Open Door

7/16" Wrench and

3/32" Hex Key (some models)

Door Stop

Flange

5. Reinstall the set screw, locking the

door height.

6. Replace the toe grille by ﬁtting it into

place (see “Toe Grille Installation

and Removal” in INSTALLATION).

4. After leveling, verify the door stop

contacts the lower hinge and the

top of the door does not contact the

upper hinge through full movement

of the door (from fully closed to

fully open).

INSTALLATION

To level the doors using the adjustable

lower hinge:

1. Before leveling either door, remove

the set screw that locks the door

height into position. (The door

cannot be adjusted without the set

screw removed).

2. If the refrigerator door is lower than

the freezer door, raise the refrigera-

tor door by turning the adjustment

screw counterclockwise using a

7

/

16

"

wrench. (See illustration.)

3. If the freezer door is lower than the

refrigerator door, raise the freezer

door by turning the adjustment

screw counterclockwise using a

7

/

16

"

wrench. (See illustration.)



NOTE

Some models will not have a set screw. For

those models follow steps 2 through 4.

10

DOOR REMOVAL

To prepare for removing the doors:

1. Make sure the electrical power cord

is unplugged from the wall outlet.

2. Open both doors and remove the

toe grille (as explained in the Instal-

lation Instructions that came with

your appliance).

3. Remove any food from the door shelves.

4. Close the doors.

To remove the refrigerator door:

1. Remove the 3 screws from the cover

over the door hinge.

2. Lift hinge cover straight up and o.

3. Trace lightly around the door’s top

hinge with a pencil. This makes

reinstallation easier. Remove the 2

screws from the top hinge. Lift the

door o of the bottom hinge and set

it aside.

Rear Cover

Screw

Front Cover

Screws

Top

Hinge

Cover

Hinge

Screws

Top

Hinge

Socket

Wrench Set

Adjustable

Wrench

Top Hinge

Cover Front

Screw

Top

Hinge

Screw

Bottom

Hinge

Screw

Top Hinge

Cover Rear

Screw

Phillips™

Head

Tools Necessary:

or

⅜" Fixed

Wrench

Phillips™

Head

&

Flathead

Screwdriver

To reinstall the refrigerator door, reverse

the above steps.

Door

Hinge

Assembly

Closer

Hinge

Screws

Adjustable Hinge (some models)

4. Remove the 2 bottom hinge screws

and hinge if necessary.

11

DOOR REMOVAL

CAUTION

Be sure doors are set aside in a secure

position where they cannot fall and

cause personal injury.

Door

Hinge

Assembly

Screws

Water

Line

Tubing

Non-Adjusting Hinge (some models)

Closer

Hinge

Door

Water

Line

Tubing

Screws

Hinge

Assembly

Adjustable Hinge (some models)

To remove the freezer door:

1. Remove the 3 screws from the cover

over the top door hinge.

2. Lift hinge cover straight up and o.

3. Release the wires from the routing clip.

Disconnect the multi-wire cable

connector located above the top

hinge. Press the cable and lock and

separate the 2 cables.

4. Trace lightly around the hinge with a

pencil. This makes reinstallation easier.

5. Detach the water tube from the

connector located below the freezer

door. The connector releases when

you press its outer sleeve inward.

6. Remove the 2 screws from the top

hinge. Remove the hinge pulling the

multi-wire cable through it. Lift the

door o the bottom hinge.

7. Remove the 2 bottom hinge screws

and hinge if necessary.

8. Lay the door on its side to avoid

damage to the water tube extending

from the bottom hinge.

To reinstall the freezer door, reverse the

above steps.

To Disconnect

1. Press outer ring against face of

fitting

2. Pull to

remove tube

Insert tube and push until mark

touches face of fitting

To Connect

IMPORTANT

To prevent wire damage, ensure the

wires are rerouted through the routing

clip when reassembling the hinge cover.

12

DOOR HANDLE INSTALLATION

1. Remove handles from carton and

any other protective packaging.

2. Position the freezer handle end caps

over the upper and lower pre-in-

stalled shoulder bolts (A) that are

fastened into door, ensuring the

holes for the set screws are facing

toward the refrigerator door.

3. While holding the handle ﬁrmly

against door, fasten the upper and

lower Allen set screws (B) with the

supplied Allen wrench.

4. Repeat steps 2 and 3 to install refrig-

erator handle. Ensure the holes for

the set screws are facing towards the

freezer door.

Freezer

Upper

End Cap

Door

Refrigerator

Upper

End Cap

Door

Refrigerator

Lower

End Cap

Door

Freezer

Lower

End Cap

Door

Ensure Handle Set Screws are Facing Each Other with Doors Closed

CAUTION

Wear gloves and safety goggles and

use extreme CAUTION when installing

these handles. The rounded end of the

handles may be sharp (some models).



NOTE

Tighten and sub-ﬂush all set screws (place the Allen set screw just below the sur-

face of the end cap) of the handle end cap. Draw the end caps tight to the freezer

and refrigerator doors with no gaps. To avoid scratching the metal door, keep the

door open while torquing down the set screws.

IMPORTANT

To ensure proper installation of handles,

please review these instructions and

illustrations thoroughly prior to installing

the handles.

Handles may vary according to model

13

WATER SUPPLY CONNECTION

Before Installing The Water Supply Line,

You Will Need:

• Basic Tools: adjustable wrench,

ﬂat-blade screwdriver, and Phillips

TM

screwdriver

• Access to a household cold water

line with water pressure between 30

and 100 psi.

• A water supply line made of ¼" (6.4

mm) OD, copper or stainless steel

tubing. To determine the length of

tubing needed, measure the distance

from the ice maker inlet valve at the

back of the refrigerator to your cold

water pipe. Then add approximately

7� (2.1 m), so the refrigerator can be

moved out for cleaning.

To Connect Water Supply Line To Ice

Maker Inlet Valve

1. Disconnect the refrigerator from

electrical power source.

2. Place the end of the water supply

line into a sink or bucket. Turn ON

the water supply and ﬂush the supply

line until the water is clear. Turn OFF

the water supply at the shuto valve.

3. Remove the plastic cap from the wa-

ter valve inlet and discard the cap.

4. If you use copper tubing - Slide the

brass compression nut, and then

the ferrule (sleeve) onto the water

supply line. Push the water supply

line into the water valve inlet as far

as it will go (¼"/6.4 mm). Slide the

ferrule (sleeve) into the valve inlet

and ﬁnger tighten the compression

nut onto the valve. Tighten another

half turn with a wrench; DO NOT

overtighten. See Figure 1.

• A shuto valve to connect the water

supply line to your household water

system. DO NOT use a self-piercing

type shuto valve.

• Do not reuse compression ﬁtting or

use thread seal tape.

• A compression nut and ferrule

(sleeve) for connecting a copper

water supply line to the ice maker

inlet valve.

WARNING

To avoid electric shock, which can

cause death or severe personal injury,

disconnect the unit from electrical pow-

er source before connecting a water

supply line to the appliance.

CAUTION

To Avoid Property Damage:

• Use Copper or Stainless Steel braid-

ed tubing for the water supply line.

Frigidaire does not recommend wa-

ter supply tubing made of ¼" plastic.

Plastic tubing greatly increases the

potential for water leaks, and the

manufacturer will not be responsible

for any damage if plastic tubing is

used for the supply line.

• DO NOT install water supply tubing

in areas where temperatures fall

below freezing.

• Chemicals from a malfunctioning

softener can damage the ice maker.

If the ice maker is connected to soft

water, ensure that the softener is

maintained and working properly.



NOTE

Check with your local building authori-

ty for recommendations on water lines

and associated materials prior to in-

stalling your new refrigerator

. Depend-

ing on your local/state building codes,

Frigidaire recommends for homes with

existing valves its Smart Choice

®

water

line kit 5304490728 (with a 6�Stain-

less Steel Water Line) and for homes

without an existing valve, Frigidaire

recommends its Smart Choice

®

water

line kit 5304490717 (with a 20�copper

water line with self-tapping saddle

valve). Please refer to Frigidaire.com

for more information.

IMPORTANT

Ensure your water supply line connections

comply with all local plumbing codes.

14

WATER SUPPLY CONNECTION

If you use braided ﬂexible stainless

steel tubing - The nut is already

assembled on the tubing. Slide the

nut onto the valve inlet and ﬁnger

tighten the nut onto valve. Tighten

another half turn with a wrench; DO

NOT overtighten. See Figure 2.

IMPORTANT

After connecting the water supply, refer

to “Priming the Water Supply System”

for important information about priming

an empty water supply system.

Your refrigerator’s water supply system

includes several tubing lines, a water

ﬁlter, and a water valve. To ensure that

your water dispenser works properly,

completely ﬁll this system with water

when you ﬁrst connect your refrigerator

to the household water supply line.

5. With the steel clamp and screw,

secure the water supply line (copper

tubing only) to the rear panel of

refrigerator as shown.

6. Coil the excess water supply line

(copper tubing only), about 2½ turns,

behind refrigerator as shown and

arrange coils so they do not vibrate or

wear against any other surface.

7. Turn ON the water supply at shuto

valve and tighten any connections

that leak.

8. Reconnect the refrigerator to elec-

trical power source.

A B

C

D

E

F

G

H

I

Figure 1

A Plastic Water Tubing to

Ice Maker Fill Tube

B Steel Clamp

C Brass Compression Nut

D Ferrule (Sleeve)

E Copper Water Line

F Water Valve Bracket

G Valve Inlet

H Water Valve

I Copper Water Line from

Household Water Supply*

J Braided Flexible Stainless Steel

Water Line

K 6 ft. (1.8 m) Braided Flexible

Stainless Steel Water Line from

Household Water Supply*

*Include enough tubing in the loop to allow

moving the refrigerator out for cleaning

A B

J

F

G

H

K

Figure 2

15

CONTROLS AND SETTINGS

Sleep Mode

Sleep mode is default on. When sleep mode is on, the LEDs are not illuminated on the

display. Sleep mode can be changed to have the display on full time (Awake Mode).

While in sleep mode pressing any key will illuminate LEDs and then go back to sleep

after a short time. To turn sleep mode on/o, simultaneously press and hold Crush and

for 5 seconds. A tone will conﬁrm.

Active Mode Display

Sleep Mode Display

Active Mode

To change from sleep mode (on) to active mode (o), simultaneously press and hold

Crush and for 5 seconds. The display will show the current temperature/ice maker

status. A tone will conﬁrm.



NOTE

Your appliance may have some or all of the features listed below. Become familiar

with these features and their use and care.

16

CONTROLS AND SETTINGS

WARNING

When using the cold drink timer, make

sure to remove drinks from freezer

compartment when alarm sounds.

Carbonated drinks may explode if left

in freezer for too long.

1

Freeze Boost (on/o)

Activates a faster rate for freezing

food in the freezer. Use this feature

when loading several items into the

freezer at one time. It automatically

deactivates after 12 hours.

2

Cold Drink Timer

Quickly chills a drink inside the freez-

er compartment. To enable, touch

Cold Drink Timer. A time value will

appear on the freezer temp display

(in minutes) and can be changed

using the +/- buttons. A tone will

sound when the time has been input.

It ranges from 20-45 minutes in 5

minute intervals. Drinks will freeze if

the temperature setting is too low or

the timer setting is too long.

3

Ice Maker

Press and hold for 3 seconds to

turn the ice maker on/o. When

the indicator is lit, the ice maker is

on. When the ice maker is o, the

ice maker o indicator is lit. When

the ice maker is o, it will stop

making ice. While o, ice dispensing

can continue as long as there is

ice in the bucket. When the ice

maker is o and ice is dispensing,

the indicator above the ice maker

button and ice maker OFF will both

blink. If the display is in sleep mode,

you will have to wake it to conﬁrm

the ice maker is on/o.

4

The lock button can be used to lock

the display preventing it from being

used in certain situations. Press

and hold for 3 seconds to enable/

disable. While in the locked state,

no changes can be made to settings

on the display. Dispensing ice and

water will be disabled. The indicator

will ﬂash and an audible warning

tone sounds.

5

Power Outage

In the event of a power failure, the

Power Outage alert will illuminate

once power has been restored, and

a tone will sound. Press any button

to silence the tone.

Display

1

2

3

4

5

6

7

8 9

10 11 12

13

14

15

16

17

CONTROLS AND SETTINGS

°F/°C

To toggle between Fahrenheit (°F)

and Celsius (°C), simultaneously

press and hold + and - for 5 seconds

on refrigerator side of display.

Chill Boost

Chill Boost is a faster rate for

chilling food in the refrigerator

compartment. Use this feature

when loading several items into the

refrigerator at one time. Deactivates

after 6 hours.

Air Filter

The display shows the current

status of the air ﬁlter (Good, Order,

or Replace). To reset the ﬁlter

status to Good, press and hold Air

Filter for 3 seconds.

Water Filter

The display shows the current

status of the water ﬁlter (Good,

Order, or Replace). To reset the

ﬁlter status to Good, press and hold

Water Filter for 3 seconds.

Toggles dispenser light On and O.

13

14

15

16

17

Power

Outage

In the event of a power out-

age, the Power Outage alert

will illuminate once power

has been restored and a tone

will sound. Press any button

to silence the tone.

Door

Open

If you leave a door open for

5 minutes or more, an alarm

will sound and the Door

Open indicator will illuminate

on the display. Turn the alarm

o by closing the door or

pressing any key. The control

panel will return to normal

operations after you close

the door.

Alarms

6

Adjusting Temp

Illuminates when temperatures are

changed on the display and will

remain illuminated until the desired

temperatures are reached inside

the refrigerator and freezer. Press

either the + or - to adjust to desired

temperature setting.

Freezer temp

Control temperatures range from

-6°F / -21°C to +4°F / -15°C.

Refrigerator temp

The Control temperature ranges

from +33°F / +1°C to +43°F / +7°C.

This unit is designed to operate at

39°F refrigerator/0°F freezer. The

unit should stabilize temperatures

within 24 hours of installation.

Door Open

Illuminates whenever the doors are

open. If a door is left open for 5

minutes or more, an alarm will sound

and the display will be illuminated

until the doors are shut. Pressing

any button will mute the alarm

temporarily. Check to make sure no

food is blocking the doorway.

Replace Water Filter

Display illuminates every 6 months

or when ﬁlter needs replacing.

Replace ﬁlter and then press and

hold Reset Water Filter for 3

seconds to deactivate warning on

display. See “Replacing the Filter”

section for more information.

Replace Air Filter

Display illuminates every 6 months

or when ﬁlter needs replacing.

Replace ﬁlter and then press and

hold Reset Air Filter for 3 seconds

to deactivate warning on display.

See “Replacing the Filter” section

for more information.

Water

Press Water to dispense water. An

indicator light will be illuminated

above the active feature.

Cube

Press Cube to dispense cubed ice.

An indicator light will illuminate

above the active feature.

Crush

Press Crush to dispense crushed

ice. An indicator light will illuminate

above the active feature.

7

8

9

10

11

12

18

CONTROLS AND SETTINGS

Sabbath Mode

The Sabbath mode is a feature that

disables portions of the refrigerator

and its controls in accordance with

observance of the weekly Sabbath and

religious holidays within the Orthodox

Jewish community.

Turn the Sabbath mode ON and OFF by

simultaneously pressing and holding both

the - (freezer side) and + (refrigerator

side) for 5 seconds. Other than the High

Temp alarm, no audible sounds will occur

until you exit the Sabbath mode. The dis-

play shows Sb while in Sabbath mode.

Water

Filter

The water ﬁlter needs to be

replaced when the indicator

illuminates. Change the water

ﬁlter every 6 months or after

you have dispensed 120 gal-

lons of water. To reset, press

and hold the button for 3 sec-

onds. A tone will then sound.

Air

Filter

The air ﬁlter needs to be

replaced when the indicator

illuminates. Change the air ﬁlter

every 6 months. To reset, press

and hold the button for 3 sec-

onds. A tone will then sound.

Error

Tone

An alarm will sound if you try

to make a selection that is

not available.

High

Temp

In the event of the internal

temperature of the refriger-

ator rising and staying at a

temperature above the safe

temp zone for a period of

time, HI will display on the

corresponding compartment

display (refrigerator and/or

freezer). An alarm will sound

in addition to the display

warning every 10 seconds

until acknowledged. The

refrigerator will automatically

try to cool down to improve

the condition. However, if the

temperature has not cooled

after some time, the warning

and alarm will appear again.

If the problem continues

please call 1 (800) 374-4432.

In the Sabbath mode, the High Temp

alarm is active for health reasons. For

example, if the door is left ajar the High

Temp alarm is activated. The refrigerator

will function normally once the door

is closed, without any violation of the

Sabbath/Holidays. The High Temp

alarm is permitted when the cabinet

temperature is outside the safe zone for

20 minutes. The alarm silences itself after

10 minutes while the High Temp icon

stays lit until you exit the Sabbath mode.

For further assistance, guidelines

for proper usage and a complete

list of models with the Sabbath

feature, please visit the web at

star-k.org.

Alarms (continued)



NOTE

Although you have initiated the Sab-

bath mode, the ice maker will complete

the cycle it had already started. The

ice cube compartment will remain cold

and you can make new ice cubes with

standard trays.



NOTE

While in Sabbath mode, neither the lights,

dispenser, nor the control panel will work

until Sabbath Mode is deactivated.

The refrigerator stays in Sabbath mode

after power failure recovery. You must

deactivate it with the buttons on the

control panel.



NOTE

You should exit the Sabbath mode at

your earliest convenience as the unit

runs more eciently out of the Sab-

bath mode.

19

AUTOMATIC ICE AND WATER DISPENSER

Priming the water supply system

Ice maker operation & care

After you properly install the refrigerator

and it has cooled for several hours, the ice

maker can produce ice within 24hours.

The ice maker will ﬁll the ice bin from the

rear. You must dispense some ice to force

the ice forward in the bin. This will allow

the bin to ﬁll completely.

1. Begin ﬁlling

the system

by pressing

and holding

a drinking

glass against

the water

dispenser

paddle.

2. Keep the

glass in this

position until

water comes

out of the

dispenser. It may take about

1½ minutes. Water will sputter until

you purge all air from the water lines.

3. Continue dispensing water for about

4 minutes to ﬂush the system

and plumbing connections of any

impurities (stopping to empty the

glass as necessary).

Power Outage

Cube

ICE

WATER

Crush

Door Open

High Temp

Replace Water Filter

Replace Air Filter

Dispenser

(varies by model)

CAUTION

For proper dispenser operation, the

recommended water supply pressure

should fall between 30psi and 100psi.

Excessive pressure may cause the sys-

tem to malfunction.

Turning the ice maker on

Ice production is controlled by the ice

maker's On/O feature on the control

panel. Pressing and holding the On/O

button toggles the ice maker On/O.



NOTE

Dispensed water is not chilled. For

colder water, add ice to cup or contain-

er before dispensing water.



NOTE

The ice maker also has a built-in plastic

signal arm that automatically stops ice

production when the ice bin is full. Do

not use this signal arm to manually stop

the ice maker.



NOTE

The water dispenser has a built-in de-

vice that shuts o the water ﬂow after

3 minutes of continuous use. To reset

this shuto device, simply release the

dispenser paddle.

IMPORTANT

Turning o the ice maker simply dis-

ables ice making. You will still be able to

dispense existing ice, and you will still be

able to dispense water.

20

Ice Maker/Dispenser Tips

• Ice cubes stored too long may

develop an odd ﬂavor. Empty the ice

container as explained in Cleaning the

Ice Storage Bin.

• Occasionally shake the ice container

to keep ice separated.

• If your refrigerator is not connected to

a water supply or the water supply is

turned o, turn O the ice maker.

• If you need a large quantity of ice

at one time, it is best to get cubes

directly from the ice container.

• The following sounds are normal

when the ice maker is operating:

- Motor running

- Ice dropping into ice container

- Water valve opening or closing

- Ice loosening from tray

- Running water

• When dispensing ice, you will hear a

snapping or clicking sound when the

ice chute opens and closes.

• Turn O the ice maker when cleaning

the freezer and during vacations. If

you turn O the ice maker for a long

period of time, you should also turn

o the water supply valve.

Cleaning the Ice Storage Bin

Clean the ice storage bin at regular

intervals, particularly before you take a

vacation or move.

To clean the ice storage bin:

1. Turn O the ice maker.

2. Remove the ice storage bin by lifting

up and out.

3. Empty and carefully clean the ice

storage bin with mild detergent.

Rinse with clear water. Do not use

harsh or abrasive cleaners.

CAUTION

Chemicals from a malfunctioning water

softener can damage the ice maker. If

the water supply to your refrigerator is

softened, be sure the softener is main-

tained to work properly.

CAUTION

NEVER use an ice pick or similar sharp

instrument to break up the ice. This

could damage the ice storage bin and

dispenser mechanism.

4. Allow the ice storage bin to dry com-

pletely before replacing it in the freezer.

5. Remove ice chips and clean the ice

storage bin, shelf and the freezer

door chute.

6. Replace the ice storage bin. Turn On

the ice maker to resume ice production.

Remove and empty the ice storage bin if:

• An extended power failure (1 hour or

longer) causes ice cubes in the ice

storage bin to melt and freeze togeth-

er, jamming the dispenser mechanism.

• You do not use the ice dispenser

frequently. Ice cubes will freeze

together in the bin, jamming the

dispenser mechanism.

Remove the ice storage bin and shake

to loosen the cubes or clean as

explained above.

AUTOMATIC ICE AND WATER DISPENSER

Auger

IMPORTANT

When removing or replacing the ice

storage bin, avoid rotating the auger in the

ice storage bin. If the auger is accidentally

rotated, you must realign the auger by

turning it in 45 degree turns (see below)

until the ice storage bin ﬁts into place with

the drive mechanism If the auger is not

properly aligned when replacing the ice

storage bin, the refrigerator will not dis-

pense ice. The freezer door also may not

close properly causing warm air to leak

into the freezer compartment.

La page charge ...

Frigidaire Gallery GRSC2352AD Mode d'emploi

Ce manuel convient également à

Frigidaire Gallery GRSC2352AD Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents