Roper YRT14ZKYGW00 Le manuel du propriétaire

Marque: Roper

Modèle: YRT14ZKYGW00

Catégorie: Frigos

Taper: Le manuel du propriétaire

Ce manuel convient également à

BYWHIRLPOOL CORPORATION

TOP-MOUNT

REFRIGERATOR

For questions about features, operation/performance,

parts accessories or service, call: 1-800-44-ROPER (1-800-447-6737).

In Canada, call for assistance 1-800-461-5681, for installation

and service, call: 1-800-807-6777

or visit our website at...

www.roperappliances.com

RI FRIGI RATEoUR

SUPERPOSE

_#_%= =i_ =i_ ...... !ili =iiaiii_ ...... iiii! ..........

l< :

Au Canada, pour assistance, composer le

1-800-44-ROPER (1-800-447-6737),

pour installation ou service le 1-800-807-6777

ou visitez notre site web

www.roperappliances.com

Table of Contents/Table des matieres ....................................... 2

2213900

TABLEOFCONTENTS

REFRIGERATOR SAFETY .......................................................... 3

INSTALLING YOUR REFRIGERATOR .......................................... 4

Unpacking Your Refrigerator ....................................................... 4

Space Requirements .................................................................... 4

Electrical Requirements ............................................................... 5

Connecting the Refrigerator to a Water Source .......................... 5

Refrigerator Doors: Removing,

Reversing (optional) and Replacing ............................................. 7

Door Closing and Alignment ........................................................ 8

Understanding Sounds You May Hear........................................ 9

USING YOUR REFRIGERATOR .................................................... 9

Ensuring Proper Air Circulation .................................................... 9

Setting the Control(s) ................................................................. 10

Adjusting Control Settings ......................................................... 10

Ice Maker .................................................................................... 11

REFRIGERATOR FEATURES ...................................................... 11

Refrigerator Shelves ................................................................... 11

Meat Drawer and Cover ............................................................. 11

Crisper and Crisper Cover ......................................................... 12

Utility or Egg Bin......................................................................... 12

FREEZER FEATURES .................................................................. 13

Freezer Shelf .............................................................................. 13

DOOR FEATURES ........................................................................ 13

Drop-in Door Rails...................................................................... 13

CARING FOR YOUR REFRIGERATOR ....................................... 13

Cleaning Your Refrigerator ......................................................... 13

Changing the Light Bulb ............................................................ 14

Power Interruptions .................................................................... 14

Vacation and Moving Care ......................................................... 14

TROUBLESHOOTING .................................................................. 15

ASSISTANCE OR SERVICE ......................................................... 17

WARRANTY .............................................................................. 18

TABLEDESMATIERES

SECURITE_ DU REFRIGERATEUR ........................................... 19

INSTALLATION DU RE_FRIGERATEUR ...................................... 20

Deballage de votre refrigerateur ................................................ 20

Espacement requis ..................................................................... 20

Specifications electriques .......................................................... 21

Raccordement du refrigerateur

une canalisation d'eau ............................................................ 21

Portes du rdrigerateur : Demontage,

inversion (option) et reinstallation ............................................... 23

Fermeture et alignement des portes .......................................... 25

Les bruits de I'appareil que vous pouvez entendre ................... 25

UTILISATION DU REFRIGE_RATEUR .......................................... 26

Pour s'assurer d'une circulation d'air appropriee ...................... 26

Reglage des commandes .......................................................... 26

Ajustement des reglages de commande ................................... 26

Machine a glaqons ..................................................................... 27

CARAOTE_RISTIQUES DU REFRIGERATEUR ........................... 28

Tablettes du rdrigerateur ........................................................... 28

Bac a viande et couvercle .......................................................... 28

Bac a legumes et couvercle ....................................................... 28

Casier utilitaire ou oeufrier .......................................................... 29

CARACTE_RISTIQUES DU CONGI_LATEUR ............................... 29

Clayette du congelateur ............................................................. 29

CARACTE_RISTIQUES DE LA PORTE ......................................... 30

Tringles dans la porte ................................................................. 30

ENTRETIEN DE VOTRE RE_FRIGERATEUR ............................... 30

Nettoyage du refrigerateur ......................................................... 30

Remplacement de I'ampoule d'eclairage .................................. 31

Pannes de courant ..................................................................... 31

Entretien avant les vacances

ou Iors d'un demenagement ...................................................... 31

DI_PANNAGE ................................................................................. 32

ASSISTANCE OU SERVICE ......................................................... 35

GARANTIE ................................................................................. 36

REFRIGERATORSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all

safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or

"WARNING." These words mean:

You can be killed or seriously injured if you don't

immediately follow instructions.

You can be killed or seriously injured if you don't

follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you

what can happen if the instructions are not followed.

IMPORTANTSAFETYINSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic

precautions:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

• Disconnect power before servicing.

• Replace all panels before operating.

• Remove doors from your old refrigerator.

Use nonflammable cleaner.

• Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

• Use two or more people to move and install

refrigerator.

• Disconnect power before installing ice maker (on

ice maker kit ready models only).

• Use a sturdy glass when dispensing ice or water

(on some models).

SAVETHESEINSTRUCTIONS

ProperDisposalofYour

Old Refrigerator

Before you throw away your old refrigerator or freezer:

• Take off the doors.

• Leave the shelves in place so that children may not easily

climb inside.

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or

brain damage.

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for '_justa few days." I[ you are getting rid of

your old refrigerator, please follow these instructions to help

prevent accidents.

INSTALLINGYOUR

REFRIGERATOR

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

Remove shelves from the shipping position (shelves are

shipped upside down):

1. Grasp the front of the upper shelf with one hand and use the

other hand to remove packing material from the shelf area.

2. Lower the front of the upper shelf until shelf hooks can be

removed from the shelf supports and pull the shelf forward.

3. Flip the shelf over and insert the rear shelf hooks into the

shelf supports. Tilt the front of shelf up until rear shelf hooks

drop into the shelf supports.

4. Lower the front of the shelf and check to make sure that it is

securely in position.

Removing packaging materials

• Remove tape and glue from your refrigerator before using. To

remove any remaining tape or glue, rub the area briskly with

your thumb. Tape or glue residue can also be easily removed

by rubbing a small amount of liquid dish soap over the

adhesive with your fingers. Wipe with warm water and dry.

• Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator. For

more information, see "Refrigerator Safety" section.

• On some models, shelves, bins, door shelf rails, and other

feature parts may be packaged in the Interior FeaturePak.

Follow the instructions contained in the package for proper

assembly

• Depending on your model, to remove the protective

(transparent) film that is on the nameplate, which is located

on the freezer handle, use your fingernail and peel off the film,

starting from one side and peeling to the other.

IMPORTANT: Depending on your model, do not remove the

white foam air return insert that is located behind the control

panel on the ceiling of the refrigerator. The insert is part of the

refrigerator and not part of the packing material. If the insert is

removed, ice may migrate down from the freezer and cause

icicles to form.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator

for cleaning or service, be sure to protect the floor.

Always pull the refrigerator straight out when moving it.

Do not wiggle or "walk" the refrigerator when trying to move

it, as floor damage could occur.

Cleaning before use

After you remove all of the package materials, clean the inside of

your refrigerator before using it. See the cleaning instructions in

the "Caring for your Refrigerator" section.

Important information to know about glass shelves

and covers:

Do not dean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

For your protection, tempered grass is designed to shatter

into many small, pebble-size pieces. This is normal. GIass

shelves and covers are heavy. Use special care when re-

moving them to avoid impact from dropping.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion,

or fire.

• To ensure proper ventilation for your refrigerator, allow for a

.5 in. (1.25 cm) space on each side.

• Allow 3 in. (7.5 cm) of space between overhead cabinets and

refrigerator top.

• Allow at least 1 in. (2.5 cm) between back of cabinet and the

wall.

• If your refrigerator has an ice maker, make sure you leave

some extra space at the back for the water line connections,

• If you are installing your refrigerator next to a fixed wall, leave

2 in. (5,08 cm) minimum on the hinge side (depending on your

model) to allow for the door to swing open,

• Level the refrigerator (See "Door Closing and Alignment"),

NOTE: Do not install the refrigerator near an oven, radiator, or

other heat source, nor in a location where the temperature will fall

below 40°F (5°C).

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in

death, fire, or electrical shock.

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical

connection:

Recommended grounding method

A 115 Volt, 60 Hz., AC only 15 or 20 ampere fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an

extension cord.

NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn the control, (Thermostat, Refrigerator

or Freezer Control depending on the model) to OFF and then

disconnect the refrigerator from the electrical source. When you

are finished, reconnect the refrigerator to the electrical source

and reset the control (Thermostat, Refrigerator or Freezer Control

depending on the model) to the desired setting.

C:O i i :ili!:,iiiiii ?fii iii,!iiii:: !,i;iii!,?ili ::::i!ii! O ii

Read all directions carefully before you begin.

IMPORTANT:

• If operating the refrigerator before installing the water

connection, turn ice maker to the OFF position to prevent

operation without water.

• All installations must be in accordance with local plumbing

code requirements.

• Use copper tubing and check for leaks.

• Install copper tubing only in areas where temperatures will

remain above freezing.

• It may take up to 24 hours for your ice maker to begin

producing ice.

Tools required:

• Standard screwdriver

• 7A6in. and 1/2in. open-end wrenches or two adjustable

wrenches

• ¼in. nut driver

• ¼in. drill bit

• Hand drill or electric drill (properly grounded)

NOTE: Your refrigerator dealer has a kit available with a

1/4in. (6.35 mm) saddle-type shut-off valve, a union, and copper

tubing. Before purchasing, make sure a saddle-type valve

complies with your local plumbing codes. Do not use a piercing-

type or 3A6in. (4.76 mm) saddle valve which reduces water flow

and clogs more easily.

Cold Water Supply

The ice maker water valve contains a flow washer which is used

as a water pressure regulator. The ice maker needs to be

connected to a cold water line with water pressure between 30

and 120 psi. If a problem occurs, call your utility company.

Connecting to water line:

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line or water.

3. Find a 1/2in. (12.7 mm) to 11/4in. (3.18 cm) vertical COLD

water pipe near the refrigerator.

NOTE: Horizontal pipe will work, but the following procedure

must be followed: Drill on the top side of the pipe, not the

bottom. This will help keep water away from the drill. This

also keeps normal sediment from collecting in the valve.

4. To determine the length of copper tubing you will need,

measure from connection on lower left rear of refrigerator to

water pipe. Add 7 feet (2.1 m) to allow for moving refrigerator

for cleaning. Use 1/4in. (6.35 mm) O.D. (outside diameter)

copper tubing. Be sure both ends of copper tubing are cut

square.

Usingagroundeddrill,drilla¼in.(6.35mm)holeinthecold

waterpipeyouhaveselected.

...........1

7 • .........................2

1. Cold Water Pipe

2. Pipe Clamp

3. Copper Tubing

4. Compression Nut

5. Compression Sleeve

6. Shut-Off Valve

7. Packing Nut

6. Fasten shut-off valve to cold water pipe with pipe clamp. Be

sure outlet end is solidly in the 1/4in. (6.35 mm) drilled hole in

the water pipe and that washer is under the pipe clamp.

Tighten packing nut. Tighten the pipe clamp screws carefully

and evenly so washer makes a watertight seal. Do not

overtighten or you may crush the copper tubing, especially if

soft (coiled) copper tubing is used. Now you are ready to

connect the copper tubing.

7. Slip compression sleeve and compression nut on copper

tubing as shown. Insert end of tubing into outlet end squarely

as far as it will go. Screw compression nut onto outlet end

with adjustable wrench. Do not overtighten.

8. Place the free end of the tubing into a container or sink, and

turn ON main water supply and flush out tubing until water is

clear. Turn OFF shut-off valve on the water pipe. Coil copper

tubing.

Connecting to refrigerator:

NOTE: The first step for connecting the water line to your

refrigerator is different depending on the type of water valve

provided with your refrigerator. See the diagrams below to

determine the style of valve you have. (On kit models, assemble

water valve to refrigerator per kit instructions.)

1. For Style 1, disconnect the tube clamp on the back of the

product and insert the copper tubing through the clamp, as

shown. Remove the tape label from the valve inlet and insert

copper tubing until it bottoms out (approximately 3/4in. [1.9

cm]). Tighten nut by hand as much as possible; then turn the

nut an additional 1/2turn using a wrench. Do not overtighten.

Re-attach the tube clamp and tube to the back of the cabinet.

Skip to Step 2.

For Style 2, disconnect the tube clamp on the back of the

product and insert copper tubing through the clamp as

shown. Attach the copper tube to the valve inlet using a

compression nut and sleeve as shown. Tighten the

compression nut. Do not overtighten. Re-attach the tube

clamp and tube to the back of the cabinet. Move to Step 2.

2. Turn shut-offvalve ON. Check For Leaks. Tighten any

connections (including connections at the valve) or nuts that

leak.

Style I

Style 2

1. Tube Clamp

2. Copper Tubing

3. Compression Nut

4. Valve Inlet

1. Tube Clamp

2. Copper Tubing

3. Compression Nut

3. The ice maker is equipped with a built-in water strainer. If

local water conditions require periodic cleaning or a well is

your source of water supply, a second water strainer should

be installed in the 1/4in. (6.35 mm) water line. Obtain a water

strainer from your nearest appliance dealer. Install at either

tube connection.

4. Plug in refrigerator or reconnect power.

ii:i:;ii!!,_i_:::_:_iiiii_!iii_i!i;_,_:::::i!ii!_O_ii_¸DO0_ii':_,:_::!;:iii:iiii!i_,_iiiiii_,_ii_¢iO_:v!i_ii_i_iJ?ii_!!!!,_i1111!,_v_i!i:_:_i!_:_:ii!!ii_iiii_ii_i_!:iiiiii!iiiiiO_:i::;i_ii_iiiO_'_iC_iiiiiiiiC_ii_il'i,_::::!i!i:il;i!!,_!iii_i::::;_,_i::ii_Oiiiiih!_!iiiiii!i

TOOLS NEEDED: %6in. hex-head socket wrench, No. 2 Phillips screwdriver, flat-head screwdriver, %6in. open-end wrench, flat 2 in.

putty knife.

IMPORTANT: Before you begin, turn the refrigerator control OFF, unplug refrigerator or disconnect power. Remove food from doors.

1 Door Stop

2 Door Stop Screw

3 Spacer

4 Center Hinge

5 5/J6"Hex-Head Hinge Screws

6. Spacer

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii:

Bottom Hinge

2 ..............................................

1 Door Stop

2. Spacer

3. Door Stop Screw

!. Cabinet Hinge Hole Plugs

1. Door Hinge Hole Plug

1. Flat-Head Handle Screws

2. Freezer Handle

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii:

4 Bottom HIhge

5 %," Hex-Head Hinge Screws

1 _" Hex-Head Hinge

Screws and Washers

!. Door Handle

Seal Screw Front

t. Flat-Head Handle Screw

2 Refrigerator Handle

3. Handle Screw

4. Screw Cover

Door and hinge removal

"5/16in. Hex-Head Hinge Screw

1. Unplug refrigerator or disconnect power.

2. Keep both doors closed until you are ready to lift them free

from the cabinet.

NOTE: Provide additional support for the doors while the

hinges are being moved. Do not depend on the door magnets

to hold the doors in place while you are working.

3. Remove the parts for the top hinge as shown in Top Hinge

graphic.

4. Lift the freezer door free from the cabinet.

5. Remove the parts for the center hinge as shown in the Center

Hinge graphic.

6. Lift the refrigerator door free from the cabinet.

7. Remove the parts for the bottom hinge as shown in the

Bottom Hinge graphic.

IMPORTANT: If you want to reverse your doors so that they

open in the opposite direction, follow these steps. If you are

not reversing the doors, see "Door and Hinge Replacement."

Door reversal (optional)

Door Stop Screw

Door Handle Sealing Screw

Flat-Head Handle Screw

Door Handle Seal Screw Front

Door Hinge Hole Plug

Cabinet Hinge Hole Plug

Door Handle Screw Cover

Round-Head Handle Screw

Cabinet

1. Remove %6 in. hex-head hinge screws from handle side and

move them to opposite side (see Graphic 1-1).

2. Remove cabinet hinge hole plugs from cabinet top and move

them to opposite side hinge holes as shown (see Graphic 1-

2).

Freezer door

1. Remove freezer handle assembly as shown. Keep all parts

together (see Graphic 2).

2. Remove door hinge hole plug. Move to opposite side as

shown (see Graphic 3).

3. Remove door handle sealing screws. Move to opposite side

of freezer door as shown (see Graphic 4).

4. Remove door stop. Move to opposite side of freezer door as

shown (see Graphic 5).

5. Position freezer handle on opposite side of freezer door.

Assemble handle on door as shown (see

Graphic 2).

6. Tighten all screws. Set aside door until hinges and refrigerator

compartment door are in place.

Refrigerator door

1. Remove the screw cover (see Graphic 6).

2. Remove refrigerator handle assembly as shown. Keep all

parts together (see Graphic 6).

3. Remove door hinge hole plug from refrigerator door. Move to

opposite side hinge hole as shown (see Graphic 3).

4. Remove door handle sealing screws. Move to opposite side

of refrigerator door as shown (see Graphic 4).

5. Remove door handle seal screw front. Move to opposite side

of refrigerator door as shown (see Graphic 7).

6. Remove door stop. Move to opposite side of refrigerator door

as shown (see Graphic 5).

7. Position refrigerator handle on opposite side of the

refrigerator door as shown (see Graphic 6). Drive top two

screws in handle first. Align lower portion of handle and drive

bottom screw.

8. Replace screw cover (see Graphic 6).

9. Tighten all screws. Set aside refrigerator door until bottom

hinge is installed on product.

Door and hinge replacement

Note: Graphic may be reversed if door swing is reversed.

1. Replace the parts for the bottom hinge as shown. Tighten

screws.

2. Replace the refrigerator door.

NOTE: Provide additional support for the doors while the

hinges are being moved. Do not depend on the door magnets

to hold the doors in place while you are working.

3. Assemble the parts for the center hinge as shown and tighten

all screws (see Center Hinge graphic).

4. Replace the freezer door.

5. Assemble the parts of the top hinge as shown (see Top Hinge

graphic). Do not tighten screws completely.

6. Line up the doors so that the bottom of the freezer door

aligns evenly with the top of the refrigerator door. Tighten all

screws.

Final Steps

l i Check all holes to make sure that hole plugs and screws are

in place.

2. Plug in refrigerator or reconnect power.

3. Reset the controls (see "Setting the Controls" section.)

Your refrigerator has two front adjustable rollers - one on the right

and one on the left. If your refrigerator seems unsteady or you

want the doors to close easier, adjust the refrigerator's tilt using

the instructions below:

1. Roll out the refrigerator and use a level to check the floor at

the back from side-to-side. If needed, use shims to level the

back of the refrigerator if it is uneven. Roll the refrigerator

back into place with the rear rollers on top of any shim(s)

used so that the rear of the refrigerator is level.

2. With the rear already level and the refrigerator in place, use

the bottom leveling screws to level the refrigerator from side-

to-side. They are part of the front roller assemblies, which are

found at the base of the refrigerator on either side.

NOTE: Having someone push against the top of the

refrigerator takes some weight off the leveling screws and

rollers. This makes it easier to adjust the screws.

Style 1

Style 2

• Rattling noises may come from the flow of refrigerant, the

water line, or items stored on top of the refrigerator.

• Your refrigerator is designed to run more efficiently to keep

your food items at the desired temperature. The high

efficiency compressor may cause your new refrigerator to run

longer than your old one, and you may hear a pulsating or

high-pitched sound.

• Water dripping on the defrost heater during a defrost cycle

may cause a sizzling sound.

• You may hear the evaporator fan motor circulating the air

through the refrigerator and freezer compartments.

• As each cycle ends, you may hear a gurgling sound due to

the refrigerant flowing in your refrigerator.

• Contraction and expansion of the inside walls may cause a

popping noise.

• You may hear air being forced over the condenser by the

condenser fan.

• You may hear water running into the drain pan during the

defrost cycle.

USINGYOUR

REFRIGERATOR

3. Depending on your model, to level your refrigerator you may

either turn the screw clockwise to raise that side of the

refrigerator or turn the screw counterclockwise to lower that

side. Place a level on top of the refrigerator to check

adjustments.

4. If the doors do not close on their own, you will need to raise

the front of the refrigerator so it is slightly higher than the

back. To do this, turn both leveling screws clockwise 1/2turn.

IMPORTANT: Be sure to turn both screws an equal amount

or the refrigerator will no longer be level side-to-side.

5. Open doors and check if they close automatically. If not,

repeat steps 3 and 4.

6. Using a level, check to see if the refrigerator is still level side-

to-side. Readjust if necessary.

Your new refrigerator may make sounds that your old one didn't

make. Because the sounds are new to you, you might be

concerned about them. Most of the new sounds are normal. Hard

surfaces, like the floor, walls, and cabinets, can make the sounds

seem louder than they actually are. The following describes the

kinds of sounds and what may be making them.

• If your product is equipped with an ice maker, you will hear a

buzzing sound when the water valve opens to rill the ice

maker for each cycle.

• The defrost timer will click when the automatic defrost cycle

begins and ends. Also, the Thermostat Control (or

Refrigerator Control depending on the model) will click when

cycling on and off.

In order to ensure proper temperatures, you need to permit air

flow between the refrigerator and freezer sections. As shown in

the illustration, cool air enters through the bottom of the freezer

section and moves up. Most or the air then flows through the

freezer section vents and recirculates under the freezer floor. The

rest of the air enters the refrigerator section through the top vent.

Do not block any of these vents with food packages. If the

vents are blocked, airflow will be prevented and temperature and

moisture problems may occur.

IMPORTANT: Because air circulates between both sections, any

odors formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To prevent

odor transfer and drying out or rood, wrap or cover foods tightly.

(See the "Refrigerator Safety" section for details.)

Foryourconvenience,the refrigerator controls are preset at

the factory. Controls for the refrigerator and freezer are located

in the top of the refrigerator section.

When you first install your refrigerator, make sure that the

control(s) are still preset. The control(s) should be at the

"mid-settings" as shown for each style of control.

Mid-setting "3"

OFF

O0LDES_

5 1

_0_AL

_ _RM_

o,"?t_?_°,"_,.o

Mid-setting "3"

WA_ME_

Mid-setting "4"

NOTE: To turn your refrigerator off, turn the refrigerator control to

the word OFF or until the word OFF appears, as shown below.

Your product will not cool when the refrigerator control is set to

OFE

Give your refrigerator time to cool down completely before

adding food. It is best to wait 24 hours before you put food into

the refrigerator.

IMPORTANT: If you add food before the refrigerator has cooled

completely, your food may spoil. Turning the Refrigerator or

Freezer Control(s) to a higher (colder) than recommended

setting will not cool the compartments any faster.

On models with two controls, the Freezer Control functions as an

airflow director. Setting "1" will direct more of the cold air into the

refrigerator section, while setting "5" (or "T' depending on your

model) will direct more of the cold air into the freezer section. The

cold air flows from the freezer compartment through the top vent

into your fresh food section (see diagram in the "Ensuring Proper

Air Circulation" section). On models with one control, the airflow

does not require adjustment.

Give the refrigerator time to cool down completely before adding

food. It is best to wait 24 hours before you put food into the

refrigerator. The "mid-settings" indicated in the previous section

should be correct for normal household refrigerator usage. The

controls are set correctly when milk or juice is as cold as you like

and when ice cream is firm.

For models with two controls:

The Refrigerator Control functions as the thermostat for the entire

product (refrigerator and freezer sections). The higher the number

setting, the longer the compressor will run to keep the

temperature colder. The Freezer Control adjusts the cold air flow

from the freezer to the refrigerator.

If you need to adjust temperatures in the refrigerator or freezer,

start by adjusting the refrigerator first. Wait 24 hours after the

refrigerator adjustment to check the freezer temperature. If it is

too warm or too cold, then adjust the Freezer Control as well.

For models with a single control:

The Temperature Control functions as the thermostat for the

entire product (refrigerator and freezer sections). The higher the

number setting, the longer the compressor will run to keep the

temperature colder.

Use the settings listed in the chart below as a guide. Always

remember to wait at least 24 hours between adjustments.

RECOMMENDED

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR section

too warm

• Door opened often

• Large amount of food added

• Room temperature very

warm

• Blocked air stream

Turn

REFRIGERATOR Control

or TEMPERATU RE

Control to next higher

number, wait 24 hours,

then re-check

Move items out of air

stream

FREEZER section too warm/

ice not made fast enough

• Door opened often

• Large amount of food added

• Very cold room temperature

(can't cycle often enough)

• Heavy ice usage

• Blocked air stream

Turn FREEZER Control or

TEMPERATURE Control

to next higher number,

wait 24 hours, then re-

check

Move items out of air

stream

REFRIGERATOR section

too cold

• Controls not set correctly for

your conditions

Turn REFRIGERATOR

Control or

TEMPERATURE Control

to next lower number,

wait 24 hours, then re-

check

• Blocked air stream

Move items out of air

stream

FREEZER section too cold

• Controls not set correctly for

your conditions

Turn FREEZER Control or

TEMPERATURE Control

to next lower number,

wait 24 hours, then re-

check

• Blocked air stream

Move items out of air

stream

iiii,Ci_ii!ii%i;:_ii_i%ii!¸_i?_i,O_il;/,ili?!_::i:;i!':'_CC:_j_:?!_iii!ii_O_i!.!i,_)

To turn the ice maker on/off:

The on/off switch for the ice maker is a wire shut-off arm located

on the side of the ice maker.

1. To turn the ice maker on, simply lower the wire shut-off arm.

NOTE: Your ice maker has an automatic shut-off. As ice is

made, the ice cubes will fill the ice storage bin and the ice

cubes will raise the wire shut-off arm to the OFF (arm up)

position.

2. To manually turn the icemaker off, lift the wire shut-off arm to

the OFF (arm up) position and listen for the click to make sure

the ice maker will not continue to operate.

To increase ice production rate:

• Normal Ice Production: In normal ice production mode, the

ice maker should produce approximately 8 to 12 batches of

ice in a 24-hour period. If ice is not being made fast enough,

turn the Freezer Control toward a higher (colder) number in

half number steps. (For example, if the control is at 3, move it

to between 3 and 4.) Wait 24 hours and, if necessary,

gradually turn the Freezer Control to the highest setting,

waiting 24 hours between each increase.

• Maximum Ice Production (on some models): In maximum

ice production, the ice maker should produce approximately

16 to 20 batches of ice in a 24-hour period. If your refrigerator

has the maximum ice production feature, push the switch to

MAX.

REMEMBER:

• Allow 24 hours to produce the first batch of ice.

• Discard the first three batches of ice produced to avoid

impurities that may be flushed out of the system.

• The quality of your ice will be only as good as the quality of

the water supplied to your ice maker.

• Avoid connecting the ice maker to a softened water supply.

Water softener chemicals (such as salt) can damage parts of

the ice maker and lead to poor quality ice. If a softened water

supply cannot be avoided, make sure the water softener is

operating properly and is well maintained.

• It is normal for the ice cubes to be attached at the corners.

They will break apart easily.

• Do not force the wire shut-off arm up or down.

• Do not store anything on top of the ice maker or in the ice

storage bin.

REFRIGERATORFEATURES

Your model may have some or all of these features. Features that

can be purchased separately as product accessories are labeled

with the word "Accessory." Not all accessories will fit all models.

If you are interested in purchasing one of the accessories, please

call the toll-free number on the cover or in the "Assistance or

Service" section.

Important information to know about glass shelves

and covers:

Do not clean grass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

For your protection, tempered glass is designed to shatter

into many small, pebble-size pieces. This is normal. Glass

shelves and covers are heavy. Use special care when re-

moving them to avoid impact from dropping,

::i?:"

The shelves in your refrigerator are adjustable to match your

individual storage needs.

Storing similar food items together in your refrigerator and

adjusting the shelves to fit different heights of items will make

finding the exact item you want easier. Itwill also reduce the

amount of time the refrigerator door is open, and save energy.

To remove and replace a shelf:

Remove items from the shelf.1,

Slide the shelf straight out to the stop.

Depending on your model, lift back or front of the shelf past

the stop. Slide shelf out the rest of the way.

Replace the shelf by sliding the back of the shelf into the

track in the wall of the cabinet.

Guide the front of the shelf into the shelf track. Be sure to

slide the shelf in all the way.

To remove and replace the meat drawer:

1. Slide meat drawer out to the stop.

2. Lift front of meat drawer with one hand while supporting

bottom of drawer with other hand. Slide drawer out the rest of

the way.

3. Replace the drawer by sliding it back in fully past the drawer

stop.

To remove and replace the meat drawer cover

(Glass meat drawer cover on some models):

1. Remove the meat drawer.

2. Push the cover back to release the rear clips from the shelf.

Tilt the cover up at the front, and pull it forward.

3. Replace the meat drawer cover by fitting the notches and

clips on underside of the cover over the rear and center

crossbars on the shelf.

4. Lower cover into place and pull the cover forward to secure

the rear clips onto the shelf.

5. Replace the meat drawer.

Meat storage guide

Store most meat in original wrapping as long as it is airtight and

moisture-proof. Rewrap if necessary. See the following chart for

storage times. When storing meat longer than the times given,

freeze the meat.

Fresh fish or shellfish ................. use same day as purchased

Chicken, ground beef, variety meats (liver)............... 1-2 days

Cold cuts, steaks/roasts ........................................... 3-5 days

Cured meats ........................................................... 7-10 days

Leftovers - Cover leftovers with plastic wrap, aluminum foil, or

plastic containers with tight lids.

To remove and replace the crisper(s):

1. Slide crisper(s) straight out to the stop. Lift the front and slide

the crisper(s) out the rest of the way.

2. Replace the crisper(s) by sliding the crisper(s) in fully past the

stop.

Style 1

To remove and replace the plastic cover:

1. Remove the crisper(s).

2. Lift the front of the cover to remove the cover support, Then

lift the cover up and slide it out.

3. Replace the cover by fitting the cover tabs into lowest cabinet

slots and pushing them in. Lower the front retainers into

place.

4. Insert cover support (with the long tab toward the front) into

the groove on the underside of the cover.

NOTE: If the support needs adjustment, turn base clockwise

to raise or counter-clockwise to lower.

Style 2

To remove and replace the glass cover:

1. Pull the glass straight out.

2. Replace the glass by pushing it straight in.

Fruit and vegetable storage guide

Fruits: Wash, let dry and store in refrigerator in plastic bag or

crisper. Do not wash or hull berries until they are ready to use.

Sort and keep berries in original container in crisper, or store in a

loosely closed paper bag on a refrigerator shelf.

Vegetables with skins: Place in plastic bags or plastic container

and store in crisper.

Leafy vegetables: Wash in cold water, drain and trim or tear off

bruised and discolored areas. Place in plastic bag or plastic

container and store in crisper.

Depending on your model, you may have a one, two or three

piece bin. Eggs may be stored in the egg tray or loose in the bin.

NOTE: Store eggs in a covered container for long term

storage. If your model does not have an egg storage bin,

store eggs in their original container on an interior shelf.

FREEZERFEATURES

Your model may have some or all of these features. Features that

can be purchased separately as product accessories are labeled

with the word "Accessory." Not all accessories will fit all models.

If you are interested in purchasing one of the accessories, please

call the toll-free number on the cover or in the "Assistance or

Service" section.

The door rails may be removed for easier cleaning.

To remove and replace the rails:

11 Remove all items from the shelf and pull straight up on each

end of the rails.

2. Locate each end of the rail above the rail's pocket opening,

and push the rail straight down until it stops.

To remove and replace the freezer shelf:

1. Remove items from the shelf.

2. Lift back of shelf over stop and slide shelf straight out.

3. Replace the shelf by sliding the back of the shelf into the

tracks on walls of cabinet.

4. Be sure to slide the shelf in all the way.

CARING FORYOUR

REFRIGERATOR

Frozen food storage guide

Storage times will vary according to the quality and type of food,

the type of packaging or wrap used (should be airtight and

moisture-proof), and the storage temperature. Seal the package

or container securely to prevent taste and odor transfer

throughout the product. Ice crystals inside a sealed package are

normal. This simply means that moisture in the food and air

inside the package have condensed, creating ice crystals.

Put no more unfrozen food into the freezer than will freeze within

24 hours (no more than 2-3 Ib of food per cubic foot [907-1,350 g

per L] of freezer space). Leave enough space in the freezer for air

to circulate around packages. Be careful to leave enough room

for the door to close tightly.

NOTE: For more information on preparing food for freezing,

check a freezer guide or reliable cookbook.

DOOR FEATURES

Your model may have some or all of these features. Features that

can be purchased separately as product accessories are labeled

with the word "Accessory." Not all accessories will fit all models.

If you are interested in purchasing one of the accessories, please

call the toll-flee number on the cover or in the "Assistance or

Service" section.

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion,

or fire.

Both the refrigerator and freezer sections defrost automatically.

However, clean both sections about once a month to prevent

odors from building up. Wipe up spills immediately.

To clean your refrigerator:

1. Unplug refrigerator or disconnect power.

2. Remove all removable parts from inside, such as shelves,

crispers, etc.

3. Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

• Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, cleaning

waxes, concentrated detergents, bleaches or cleansers

containing petroleum products on plastic parts, interior

and door liners or gaskets.

• Do not use paper towels, scouring pads, or other harsh

cleaning tools. These can scratch or damage materials.

• To help remove odors, you can wash interior walls with a

mixture of warm water and baking soda (2 tbs to 1 qt. [26

g to .95 L] of water).

4. Wash stainless steel and painted metal exteriors with a clean

sponge or soft cloth and a mild detergent in warm water. Do

not use abrasive or harsh cleaners. Dry thoroughly with a soft

cloth.

For additional protection against damage to painted metal

exteriors, apply appliance wax (or auto paste wax) with a

clean, soft cloth. Do not wax plastic parts.

5. Clean the condenser coils regularly. Coils may need to be

cleaned as often as every other month. This may help save

energy.

Style 1 - Condenser coils behind base grille:

• Remove the base grille (see the "Base Grille" section).

• Use a vacuum with an extended attachment to clean the

condenser coils when they are dusty or dirty.

• Replace the base grille when finished.

Style 2 - Condenser coils in back of the refrigerator:

• Pull refrigerator out away from the wall (see the

"Unpacking Your Refrigerator" section).

• Vacuum coils when they are dusty or dirty.

• Roll refrigerator back into place. Make sure to leave 1 in.

(2.5 cm) between the cabinet back and the wall.

• Check to see if the refrigerator is level.

6. Plug in refrigerator or reconnect power.

NOTE: Not all appliance bulbs will fit your refrigerator. Be sure to

replace the bulb with one of the same size, shape, and wattage.

To change the refrigerator light:

1. Unplug refrigerator or disconnect power.

2. Reach behind the Control Panel and unscrew the bulb.

3. Replace the bulb with a 40-watt appliance bulb.

4. Plug in refrigerator or reconnect power.

If the electricity in your house goes off, call the power company

and ask how long it will be off.

1. If the power will be out for 24 hours or less, keep both

refrigerator doors closed to help food stay cold and frozen.

2. If the power will be out for more than 24 hours:

a) Remove all frozen food and store it in a frozen food locker.

b) Place 2 Ibs. (907 g) of dry ice in the freezer for every cubic

foot (28 L) of freezer space. This will keep the food frozen

for two to four days.

c) If neither a food locker nor dry ice is available, consume

or can perishable food at once.

REMEMBER: A full freezer stays cold longer than a partially filled

one. A freezer full of meat stays cold longer than a freezer full of

baked goods. Ifyou see that food contains ice crystals, it may be

refrozen, although the quality and flavor may be affected. If the

condition of the food is poor, dispose of it.

Vacations

If you choose to leave the refrigerator on while you're away,

use these steps to prepare your refrigerator before you leave.

1. Use up any perishables and freeze other items.

2. If your refrigerator has an automatic ice maker:

• Raise wire shut-off arm to OFF (up) position or move the

switch to the OFF (right) setting.

• Shut off water supply to the ice maker.

3. Empty the ice bin.

If you choose to turn the refrigerator off before you leave,

follow these steps.

1. Remove all food from the refrigerator.

2. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day

ahead of time.

• When the last load of ice drops, raise the wire shut-off

arm to the OFF (up) position or move the switch to the

OFF (right) setting.

3. Depending on your model, turn the Thermostat Control or

Refrigerator Control to OFR See the "Setting the Controls"

section.

4. Clean refrigerator, wipe it, and dry well.

5. Tape rubber or wood blocks to the tops of both doors to prop

them open far enough for air to get in. This stops odor and

mold from building up.

Moving

When you are moving your refrigerator to a new home, follow

these steps to prepare it for the move.

1. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day

ahead of time.

• Disconnect the water line from the back of the

refrigerator.

• When the last load of ice drops, raise the wire shut-off

arm to the OFF (up) position or move the switch to the

OFF (right) setting.

2. Remove all food from the refrigerator and pack all frozen food

in dry ice.

3. Empty the ice bin.

4. Depending on your model, turn the Thermostat Control or

Refrigerator Control to OFR See the "Setting the Controls"

section.

5. Unplug the refrigerator.

6. Empty water from the defrost pan.

7. Clean, wipe, and dry thoroughly.

8. Take out all removable parts, wrap them well, and tape them

together so they don't shift and rattle during the move.

9. Depending on the model, raise the front of the refrigerator so

it rolls more easily OR screw in the leveling legs so they don't

scrape the floor. See the "Door Closing" or "Leveling Your

Refrigerator" section.

10. Tape the doors shut and the power cord to the refrigerator

cabinet.

When you get to your new home, put everything back

and refer to the "Installing Your Refrigerator" section for

preparation instructions. Also, if your refrigerator has an

automatic ice maker, remember to reconnect the water supply to

the refrigerator.

TROUBLESHOOTING

Try the solutions suggested here first in order to avoid the

cost of an unnecessary service call.

Your refrigerator will not operate

• Is the power supply cord unplugged?

Plug into a grounded 3 prong outlet.

• Has a household fuse or circuit breaker tripped?

Replace the fuse or reset the circuit.

• Is the Refrigerator Control turned to the OFF position?

Refer to the "Setting the Control(s)" section.

• Is the refrigerator defrosting?

Recheck to see if the refrigerator is operating in 30 minutes.

Your refrigerator will regularly run an automatic defrost cycle.

The lights do not work

• Is the power supply cord unplugged?

Plug into a grounded 3 prong outlet.

• Is a light bulb loose in the socket?

Turn the refrigerator control to OFE Disconnect the

refrigerator from the electrical supply. Gently remove the bulb

and reinsert. Then reconnect the refrigerator to the electrical

supply and reset the refrigerator control.

• Has a light bulb burned out?

Replace with an appliance bulb of the same wattage, size,

and shape. See the "Changing the Light Bulb(s)" section.

There is water in the defrost drain pan

• Is the refrigerator defrosting?

The water will evaporate. It is normal for water to drip into the

defrost pan.

• Is it more humid than normal?

Expect that the water in the defrost pan will take longer to

evaporate. This is normal when it is hot or humid.

The motor seems to run too much

Is the room temperature hotter than normal?

Expect the motor to run longer under warm conditions. At

normal room temperatures, expect your motor to run about

40% to 80% of the time. Under warmer conditions, expect it

to run even more of the time.

Has a large amount of food just been added to the

refrigerator?

Adding a large amount of food warms the refrigerator. It is

normal for the motor to run longer in order to cool the

refrigerator back down. See the "Refrigerator Features"

section.

Are the doors opened often?

Expect the motor to run longer when this occurs. In order to

conserve energy, try to get everything you need out of the

refrigerator at once, keep food organized so it is easy to find,

and close the door as soon as the food is removed.

• Is the control set correctly for the surrounding

conditions?

Refer to the "Setting the Control(s)" section.

• Are the doors closed completely?

Push the doors firmly shut. If they will not shut all the way, see

"The doors will not close completely" later in this section.

• Are the condenser coils dirty?

This prevents air transfer and makes the motor work harder.

Clean the condenser coils. Refer to the "Cleaning Your

Refrigerator" section.

NOTE: Your new refrigerator will run longer than your old one due

to its high efficiency motor.

The refrigerator seems to make too much noise

• The sounds may be normal for your refrigerator.

Refer to the "Understanding Sounds You May Hear" section.

The ice maker is not producing ice

• Is the freezer temperature cold enough to produce ice?

Wait 24 hours after hook-up for ice production. See the

"Setting the Control(s)" section.

• Is the wire shut-off arm in the OFF (arm up) position?

Lower the wire shut-off arm to the ON (arm down) position.

See the "Ice Maker" section.

Is the water line shut-off valve to the refrigerator turned

on?

Turn on the water valve. See the "Connecting the Refrigerator

to a Water Source" section.

• Is an ice cube jammed in the ejector arm?

Remove the ice from the ejector arm with a plastic utensil,

Refer to the "Ice Maker" section.

Does the ice maker mold have water in it or has no ice

been produced?

Check to see if your refrigerator has been connected to your

home water supply and the supply shut-off valve is turned on,

Refer to the "Connecting the Refrigerator to a Water Source"

section.

NOTE: If not due to any of the above, there may be a problem

with the water line, Call for service,

The ice maker is producing too little ice

• Has the ice maker just been installed?

Wait 72 hours for full ice production to begin. Once your

refrigerator is cooled down, the ice maker should begin

producing 70-120 cubes every 24 hours.

• Has a large amount of ice just been removed?

Allow 24 hours for ice maker to produce more ice.

• Is the control set correctly?

Refer to the "Setting the Control(s)" section.

• Is the water shut-off valve turned completely on?

Turn valve on fully. Refer to the "Connecting the Refrigerator

to a Water Source" section.

Is there a water filter installed on the refrigerator?

This filter may be clogged or installed incorrectly. First, check

the filter installation instructions to ensure that the filter was

installed correctly and is not clogged. If installation or

clogging is not a problem, call a qualified person or a

technician.

Off-taste or odor in the ice

• Are the plumbing connections new, causing discolored or

off-flavored ice?

Discard the first few batches of ice.

• Have the ice cubes been stored for too long?

Throw old ice away and make a new supply.

• Has food in the refrigerator been wrapped properly?

Refer to the "Refrigerator Features" section.

• Do the freezer and ice bin need to be cleaned?

See the "Cleaning Your Refrigerator" section.

• Does the water contain minerals (such as sulfur)?

A filter may need to be installed to remove the minerals.

The divider between the two compartments is warm

The warmth is probably due to normal operation of the automatic

exterior moisture control, If still concerned, call for service,

Temperature is too warm

Are the air vents blocked in either compartment? This

prevents the movement of cold air from the freezer to the

refrigerator.

Remove any objects from in front of the air vents. Refer to the

"Ensuring Proper Air Circulation" section for the location of air

vents.

Are the door(s) opened often?

Be aware that the refrigerator will warm when this occurs. In

order to keep the refrigerator cool, try to get everything you

need out of the refrigerator at once, keep food organized so it

is easy to find, and close the door as soon as the food is

removed.

• Has a large amount of food just been added to the

refrigerator or freezer?

Adding a large amount of food warms the refrigerator. It can

take several hours for the refrigerator to return to the normal

temperature.

• Are the controls set correctly for the surrounding

conditions?

Refer to the "Setting the Controls" section.

There is interior moisture build-up

Are the air vents blocked in the refrigerator?

Remove any objects from in front of the air vents. Refer to the

"Ensuring Proper Air Circulation" section for the location of air

vents.

Are the door(s) opened often?

Toavoid humidity build-up, try to get everything you need out

of the refrigerator at once, keep food organized so it is easy

to find, and close the door as soon as the food is removed.

(When the door is opened, humidity from the room air enters

the refrigerator. The more often the door is opened, the faster

humidity builds up, especially when the room itself is very

humid.)

• Is the room humid?

It is normal for moisture to build up inside the refrigerator

when the room air is humid.

• Is the food packaged correctly?

Check that all food is securely wrapped. Wipe off damp food

containers before placing in the refrigerator.

• Are the controls set correctly for the surrounding

conditions?

Refer to the "Setting the Controls" section.

• Was a self-defrost cycle completed?

It is normal for droplets to form on the back wall after the

refrigerator self-defrosts.

The doors are difficult to open

• Are the gaskets dirty or sticky?

Clean gaskets and the surface that they touch. Rub a thin

coat of paraffin wax on the gaskets following cleaning.

The doors will not close completely

• Are food packages blocking the door open?

Rearrange containers so that they fit more tightly and take up

less space.

• Is the ice bin out of position?

Push the ice bin in all the way.

• Are the crisper cover, pans, shelves, bins, or baskets out

of position?

Put the crisper cover and all pans, shelves, bins, and baskets

back into their correct positions. See the "Refrigerator

Features" section for more information.

• Are the gaskets sticking?

Clean gaskets and the surface that they touch. Rub a thin

coat of paraffin wax on the gaskets following cleaning.

• Does the refrigerator wobble or seem unstable?

Level the refrigerator. Refer to the "Door Closing and

Alignment" section.

• Were the doors removed during product installation and

not properly replaced?

Remove and replace the doors according to the "Refrigerator

Doors: Removing, Reversing (optional) and Replacing"

section, or call a qualified service technician.

ASSISTANCEORSERVICE

Before calling for assistance or service, please check

"Troubleshooting," It may save you the cost of a service call, If

you still need help, follow the instructions below,

When calling, please know the purchase date and the complete

model and serial number of your appliance, This information will

help us to better respond to your request,

If you need replacement parts

If you need to order replacement parts, we recommend that you

only use FSP replacement parts. FSP replacement parts will fit

right and work right, because they are made with the same

precision used to build every new Roper appliance. To locate

FSP° replacement parts in your area, call our Customer

Interaction Center telephone number or your nearest designated

service center.

Call the Customer Interaction Center toll free at

1-800-44-ROPER (1-800-447-6737). Our consultants provide

assistance with:

• Features and specifications on our full line of appliances.

• Installation information.

Use and maintenance procedures.

Accessory and repair parts sales.

Specialized customer assistance (Spanish speaking, hearing

impaired, limited vision, etc.).

Referrals to local dealers, repair parts distributors, and

service companies. Whirlpool designated service technicians

are trained to fulfill the product warranty and provide after-

warranty service, anywhere in the United States.

To locate the Whirlpool designated service company in your

area, you can also look in your telephone directory Yellow

Pages.

For further assistance

If you need further assistance, you can write to Whirlpool

Corporation with any questions or concerns at:

Whirlpool Brand Home Appliances

Customer Interaction Center

c/o Correspondence Dept.

MD 8020

553 Benson Road

Benton Harbor, MI 49022-2400

Please include a daytime phone number in your correspondence.

Call the Inglis Limited Customer Interaction Center toll free: 1-

800-461-5681 8:30 a.m. - 5:30 p.m. (EST)

Our consultants provide assistance with:

• Features and specifications on our full line of appliances.

• Referrals to local dealers.

For service in Canada

Call 1-800-807-6777. Inglis Limited designated service

technicians are trained to fulfill the product warranty and provide

after-warranty service, anywhere in Canada.

For further assistance

If you need further assistance, you can write to Inglis Limited with

any questions or concerns at:

Customer Interaction Center

Inglis Limited

1901 Minnesota Court

Mississauga, Ontario L5N 3A7

Please include a daytime phone number in your correspondence.

ROPERREFRIGERATORWARRANTY

ONE-YEAR FULL WARRANTY ON REFRIGERATOR

For one year from the date of purchase, when this refrigerator is operated and maintained according to instructions attached to or

furnished with the product, Whirlpool Corporation will pay for FSP" replacement parts and repair labor costs to correct defects in

materials or workmanship. Service must be provided by a Whirlpool designated service company.

FIVE-YEAR FULL WARRANTY ON SEALED REFRIGERATION SYSTEM

For five years from the date of purchase, when this refrigerator is operated and maintained according to instructions attached to or

furnished with the product, Whirlpool Corporation will pay for FSP'_replacement parts and repair labor costs to correct defects in

materials or workmanship in the sealed refrigeration system. These parts are: compressor, evaporator, condenser, dryer, and connecting

tubing. Service must be provided by a Whirlpool designated service company.

Whirlpool Corporation will not pay for:

1. Service calls to correct the installation of your refrigerator, to instruct you how to use your refrigerator, to replace house fuses or

correct house wiring or plumbing, or to replace light bulbs.

2. Repairs when your refrigerator is used in other than normal, single-family household use.

3. Pickup and delivery. Your refrigerator is designed to be repaired in the home.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, improper installation, acts of God, or use of products not approved

by Whirlpool Corporation.

5. Any food loss due to product failure.

6. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

7. Replacement parts or repair labor cost for units operated outside the United States or Canada.

8. In Canada, travel or transportation expenses for customers who reside in remote areas.

WHIRLPOOL CORPORATION AND INGLIS LIMITED SHALL NOT BE LIABLE FOR INCIDENTAL OR

CONSEQUENTIAL DAMAGES.

Some states or provinces do not allow the exclusion or limitation of incidental or consequential damages, so this exclusion or limitation

may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or

province to province.

Outside the 50 United States and Canada, this warranty does not apply. Contact your authorized Roper dealer to

determine if another warranty applies.

If you need service, first see the "Troubleshooting" section of this book. After checking "Troubleshooting," additional help can be found

by checking the "Assistance or Service" section or by calling the Customer Interaction Center toll free at 1-800-44-ROPER

(1-800-447-6737) from anywhere in the U.S.A. In Canada, contact the Customer Interaction Center at 1-800-461-5681 (toll free). In

Canada, contact your Ingis Limited designated service company or call 1-800-807-6777. Outside the U.S. and Canada, contact your

authorized Roper dealer. 04/oo

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or

installation date for in-warranty service.

Write down the following information about your refrigerator to

better help you obtain assistance or service if you ever need it.

You will need to know your complete model number and serial

number. You can find this information on the model and serial

number label located on the inside wall of the refrigerator

compartment.

Dealer name

Address

Phone number

Model number

Serial number

Purchase date

Sf:CURITI DU RI FRIGERATEUR

Votre securite et celle des autres est tr_s importante.

Nous donnons de nombreux messages de securite importants dans ce manuel et sur votre appareil menager.

Assurez-vous de toujours life tousles messages de securite et de vous y conformer.

_ oici le symbole d'alerte de securit&

Ce symbole d'alerte de securite vous signale les dangers potentiels de deces et de blessures graves

vous eta d'autres.

Tous les messages de securite suivront le symbole d'alerte de securite et le mot "DANGER" ou

"AVERTISSEMENT". Ces mots signifient "

Risque possible de decks ou de blessure grave si

vous ne suivez pas immediatement les instructions.

Risque possible de decks ou de blessure grave

si vous ne suivez pas les instructions.

Tousles messages de securite vous diront quel est le danger potentiel et vous disent comment reduire le risque de

blessure et ce qui peut se produire en cas de non-respect des instructions.

IMPORTANTES iNSTRUCTiONS DE SECURtT¢:

AVERTISSEMENT : Pour reduire les risques d'incendie, de choc electrique ou des blessures lots de

Futilisation du refrigerateur, prendre quelques precautions fondamentdes, y compris les suivantes :

• Brancher I'appareil sur une prise a 3 alveoles

reliee a la terre.

• Replacer tousles panneaux avant de faire la

remise en marche.

• Ne pas enlever la broche de liaison a la terre.

• Ne pas utiliser un adaptateur.

• Ne pas utiliser un cable de rallonge,

• Utiliser deux ou plus de personnes pour

deplacer et installer le refrigerateur.

• Debrancher la source de courant electrique

avant I'entretien.

• Utiliser un produit de nettoyage ininflammable.

• Garder les materiaux et les vapeurs inflammables,

telle que I'essence, loin du refrigerateur.

• Debrancher le refrigerateur avant Hnstallation de la

machine a glagons (seulement pour modeles prets

recevoir une machine a glagons),

• Utiliser un verre robuste pour prendre des glagons

ou de Feau (sur certains modeles),

• Enlever les portes de votre vieux refrigerateur.

CONSERVEZ CES iNSTRUCTiONS

Miseau rebutde votrevieux

r@frig( rateur

Avant dejeter votre vieux refrigerateur ou congelateur :

• Enlever les portes.

• Laisser les tablettes en place de sorte que les enfants ne

peuvent pas y penetrer racilement.

Risque de suffoquer

Enlever les portes de votre vieux refrigerateur.

Le non-respect de cette instruction peut causer

un decks ou des lesions cerebrales.

IMPORTANT : L'emprisonnement et I'etouffement des enrants ne

sont pas un probleme du passe. Les rdrigerateursjetes ou

abandonnes sont encore dangereux, meme s'ils sont laisses

abandonnes pendant "quelquesjours seulement". Si vous vous

debarrassez de votre vieux refrigerateur, veuillez suivre les

instructions suivantes pour aider a eviter les accidents.

IN TALI., TION DU

REFRIGERATEUR

Risque du poids excessif

Utiliser deux ou plus de personnes pour deplacer

et installer le refrigerateur.

Le non-respect de cette instruction peut causer

une blessure au dos ou d'autre blessure.

Retirer les tablettes de la position d'expedition (les

tablettes sont expediees a I'envers) :

1. Saisir le devant de la tablette superieure avec une main et

utiliser I'autre main pour enlever le materiau d'emballage de

I'espace des etageres.

2. Abaisser le devant de la tablette superieurejusqu'a ce que

les crochets de la tablette puissent etre enleves des crans sur

les supports de tablette et tirer la tablette vers I'avant.

3. Tourner completement la tablette. Inserer les crochets arriere

de la tablette dans les crans sur les supports de tablette.

Incliner le devant de la tablette vers le hautjusqu'a ce que les

crochets a I'arriere tombent dans les crans.

4. Abaisser le devant de la tablette. Verifier pour vous assurer

que la tablette est bien fixee en position.

Enlevement des materiaux d'emballage

• Enlever le ruban adhesif et la colle de votre refrigerateur avant

de I'utiliser. Pour enlever ce qui reste du ruban adhesif ou de

la colle, frotter la surface vivement avec le pouce. La colle ou

I'adhesif qui reste peut etre facilement enlevee par frottage

avec les doigts et une petite quantite de savon liquide pour la

vaisselle sur I'adhesif. Rincer a I'eau tiede et essuyer.

• Ne pas utiliser d'instruments coupants, d'alcool a friction, de

liquides inflammables ou de nettoyants abrasifs pour enlever

le ruban adhesif ou la colle. Ces produits peuvent

endommager la surface de votre refrigerateur. Pour plus de

renseignements, voir la section "Securite du refrigerateur".

• Sur certains modeles, des tablettes, bacs, glissieres de

tablettes dans la porte et autres pieces peuvent etre emballes

darts des sacs speciaux de finition FeaturePak. Suivre les

instructions contenues dans I'emballage pour le montage

approprie.

• Selon le modele que vous avez, pour enlever la pellicule

protectrice (transparente) qui recouvre la plaque signaletique

situe sur la poignee du congelateur, utiliser un ongle et

enlever la pellicule, en commenqant diun cote et en la

decollantjusqu'a I'autre cote.

IMPORTANT : Selon le modele que vous avez, ne pas enlever

I'encart en mousse Styrofoam blanche situe derriere le panneau

de reglage au plafond du refrigerateur. L'encart fair pattie du

refrigerateur et n'est pas un materiau d'emballage. Si I'encart est

enleve, de la glace peut se former en provenance du congelateur

et causer la formation de glaqons.

D&p)acement de votre r_frig_rateur :

Votre refrigerateur est Iourd. Lots du deplacement du

refrigerateur pour le nettoyage ou le service, veiller ;aproteger

le plancher. Toujours tirer le refrigerateur tout droit Iors du

deplacement. Ne pas incliner le refrigerateur d'un cote ou de

I'autre ni Je"faire marcher" en essayant de JedepJacer car Je

pJancher pourrait etre endommage.

Nettoyage avant I'utilisation

Apres avoir enleve tousles materiaux d'emballage, nettoyer

I'interieur du refrigerateur avant de liutiliser. Voir les instructions

de nettoyage darts la section "Entretien de votre refrigerateur".

(mportants renseignements _ savoir au sujet des tab(ettes

et des eouvereies en verre :

Ne pas nettoyer les tablettes en verre avec de I'eau tiede

quand ils sont froides. Les tablettes et Ies couvercles peuvent

se briser s'ils sont exposes _ des changements soudains de

temperature ou a un impact tel que coup brusque. Pour votre

protection, le verre trempe est conqu pour eclater en d'innom-

brables pieces minuscules. Ceci est normal. Les tablettes et

les couvercles en verre sont Iourds. Un soin special s'impose

lots de Jeurdeplacement pour eviter J'impact d'une chute.

Risque d'explosion

Garder les materiaux et les vapeurs inflammables,

telle que ressence, loin du refrigerateur.

Le non-respect de cette instruction peut causer

un decks, une explosion ou un incendie.

• Pour obtenir une aeration appropriee pour votre rdrigerateur,

laisser un espace de _/_po (1,25 cm) de chaque cote.

• Laisser un espace de 3 po (7,5 cm) entre le dessus du

refrigerateur et le dessous des armoires.

La page charge ...

Roper YRT14ZKYGW00 Le manuel du propriétaire

Marque: Roper

Modèle: YRT14ZKYGW00

Catégorie: Frigos

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Roper YRT14ZKYGW00 Owner's manual

Documents connexes

Roper TOP-MOUNT REFRIGERATOR Le manuel du propriétaire

Roper YRT14ZKYGW00 Le manuel du propriétaire

Ce manuel convient également à

Roper YRT14ZKYGW00 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents