Kenmore 11027092603 Le manuel du propriétaire

Catégorie
Machines à laver
Taper
Le manuel du propriétaire
OasisHE
Automatic Washers
Lavadoras autombticas
Laveuses automatiques
Models/Modelos/Modeles 110.2706#, 2707#, 2708#, 2709#
# = color number, n0mero de color, numero de couleur
Designed to use only
High Efficiency (HE) detergent
Disefiado para utilizar solamente
detergente de alta eficacia
Congu pour I'utilisation d'un
detergent haute efficacite
seulement
Sears Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. www.sears.com
8566938B Sears Canada Inc., Toronto, Ontario, Canada M5B 2B8 www.sears.ca
TABLEOF CONTENTS
PROTECTION AGREEMENTS ....................................................... 2
In the U.S.A ................................................................................... 2
In Canada ..................................................................................... 3
WARRANTY ..................................................................................... 3
WASHER SAFETY ........................................................................... 4
INSTALLATION REQUIREMENTS ................................................ 5
Tools and Parts ............................................................................ 5
Location Requirements ................................................................ 6
Drain System ................................................................................ 6
Electrical Requirements ................................................................ 7
INSTALLATION INSTRUCTIONS .................................................. 8
Before You Start ........................................................................... 8
Remove Shipping Base and Packing Ring .................................. 8
Connect Drain Hose ..................................................................... 8
Connect the Inlet Hoses ............................................................... 9
Secure the Drain Hose .............................................................. 10
Level the Washer ....................................................................... 10
Complete Installation ................................................................. 11
BENEFITS AND FEATURES ....................................................... 12
WASHER USE .............................................................................. 13
Starting Your Washer ................................................................ 13
Using the Proper Detergent ...................................................... 13
Pausing or Restarting the Washer ............................................ 14
Stopping the Washer ................................................................. 14
Changing Cycles, Modifiers and Options ................................. 14
Status Lights .............................................................................. 15
Cycles ........................................................................................ 15
Modifiers .................................................................................... 17
Options ...................................................................................... 18
Operating Controls .................................................................... 18
Normal Sounds .......................................................................... 18
LAUNDRY TIPS ............................................................................ 19
WASHER CARE ........................................................................... 19
Cleaning Your Washer ............................................................... 19
Water Inlet Hoses ...................................................................... 20
Vacation, Storage and Moving Care ......................................... 20
TROUBLESHOOTING .................................................................. 21
SERVICE NUMBERS ............................................... BACK COVER
PROTECTION AGREEMENTS
Master Protection Agreements
Congratulations on making a smart purchase. Your new
Kenmore ®product is designed and manufactured for years of
dependable operation. But like all products, it may require
preventive maintenance or repair from time to time. That's when
having a Master Protection Agreement can save you money and
aggravation.
Purchase a Master Protection Agreement now and protect
yourself from unexpected hassle and expense.
The Master Protection Agreement also helps extend the life of
your new product. Here's what's included in the Agreement:
v' Expert service by our 12,000 professional repair specialists
v' Unlimited service and no charge for parts and labor on all
covered repairs
v' "No-lemon" guarantee - replacement of your covered
product if four or more product failures occur within twelve
months
v' Product replacement if your covered product can't be fixed
v' Annual Preventive Maintenance Check at your request - no
extra charge
v' Fast help by phone - phone support from a Sears technician
on products requiring in-home repair, plus convenient repair
scheduling
v' Power surge protection against electrical damage due to
power fluctuations
v' Rental reimbursement if repair of your covered product takes
longer than promised
Once you purchase the Agreement, a simple phone call is all that
it takes for you to schedule service. You can call anytime day or
night, or schedule a service appointment online.
Sears has over 12,000 professional repair specialists, who have
access to over 4.5 million quality parts and accessories. That's
the kind of professionalism you can count on to help prolong the
life of your new purchase for years to come. Purchase your
Master Protection Agreement today!
Some limitations and exclusions apply. For prices and
additional information, call 1-800-827-6655.
Sears Installation Service
For Sears professional installation of home appliances, garage
door openers, water heaters, and other major home items, in the
U.S.A. call 1-800-4-MY-HOME ®.
_ Oanadta
Maintenance Agreements
Your purchase has added value because you can depend on
Sears HomeCentraP for service• With over 2,400 Service
Technicians and more than a million parts and accessories, we
have the tools, parts, knowledge and skills to back our pledge:
We Service What We Sell.
Your Kenmore ®product is designed, manufactured and tested to
provide years of dependable operation. But like all products, it
may require service from time to time. The Sears Maintenance
Agreement offers you an outstanding service program, affordably
priced•
The Sears Maintenance Agreement
Is your way to buy tomorrow's service at today's price
Eliminates repair bills resulting from normal wear and tear
Provides phone support from a Sears technician on products
requiring in-home repair
Even if you don't need repairs, provides an annual Preventive
Maintenance Check, at your request, to ensure that your
product is in proper running condition.
Some limitations apply. For more information about Sears
Canada Maintenance Agreements, call 1-800-361-6665.
KENMORE ELITE®APPLIANCE WARRANTY
ONE YEAR LIMITED WARRANTY
When installed, operated and maintained according to all
instructions supplied with the product, if this appliance fails due
to a defect in material or workmanship within one year from the
date of purchase, call 1-800-4-MY-HOME ®to arrange for free
repair.
TEN-YEAR LIMITED WARRANTY ON STAINLESS STEEL
DRUM AND PLASTIC TUB
For ten years from the date of purchase, when this washer is
installed, operated and maintained according to all instructions
supplied with the product, Sears will replace the stainless steel
drum and/or plastic tub due to defective materials or
workmanship. After the first year, customer assumes any labor
costs associated with replacement of these parts.
If this appliance is used for other than private family purposes,
this warranty applies for only 90 days from the date of purchase.
THIS WARRANTY COVERS ONLY DEFECTS IN MATERIAL
AND WORKMANSHIP. SEARS WILL NOT PAY FOR:
1. Expendable items that can wear out from normal use,
including but not limited to filters, belts, light bulbs, and bags.
2. A service technician to instruct the user in correct product
installation, operation or maintenance•
3. A service technician to clean or maintain this product.
4. Damage to or failure of this product if it is not installed,
operated or maintained according to all instructions supplied
with the product•
5. Damage to or failure of this product resulting from accident,
abuse, misuse or use for other than its intended purpose•
6. Damage to or failure of this product caused by the use of
detergents, cleaners, chemicals or utensils other than those
recommended in all instructions supplied with the product.
7. Damage to or failure of parts or systems resulting from
unauthorized modifications made to this product.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF
REMEDIES
Customer's sole and exclusive remedy under this limited
warranty shall be product repair as provided herein. Implied
warranties, including warranties of merchantability or fitness for a
particular purpose, are limited to one year or the shortest period
allowed by law. Sears shall not be liable for incidental or
consequential damages• Some states and provinces do not allow
the exclusion or limitation of incidental or consequential
damages, or limitations on the duration of implied warranties of
merchantability or fitness, so these exclusions or limitations may
not apply to you.
This warranty applies only while this appliance is used in the
United States and Canada.
This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state•
Sears, Roebuck and Co.
Dept. 817WA, Hoffman Estates, IL 60179
Sears Canada Inc.
Toronto, Ontario, Canada M5B 2B8
PRODUCT RECORD
In the space below, record your complete model number, serial
number, and purchase date. You can find this information on the
model and serial number label located on the product•
Have this information available to help you obtain assistance or
service more quickly whenever you contact Sears concerning
your appliance.
Model number
Serial number
Purchase date
Save these instructions and your sales receipt for future
reference.
WASHER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer follow basic precautions,
including the following:
[] Read all instructions before using the washer.
[] Do not wash articles that have been previously cleaned
in, washed in, soaked in, or spotted with gasoline,
dry-cleaning solvents, other flammable, or explosive
substances as they give off vapors that could ignite or
explode.
[] Do not add gasoline, dry-cleaning solvents, or other
flammable, or explosive substances to the wash water.
These substances give off vapors that could ignite or
explode.
[] Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been used
for 2 weeks or more. HYDROGEN GAS IS
EXPLOSIVE. If the hot water system has not been
used for such a period, before using the washing
machine, turn on all hot water faucets and let the water
flow from each for several minutes. This will release
any accumulated hydrogen gas. As the gas is
flammable, do not smoke or use an open flame during
[] Do not allow children to play on or in the washer. Close
supervision of children is necessary when the washer is used
near children.
[] Before the washer is removed from service or discarded,
remove the door or lid.
[] Do not reach into the washer if the drum, tub or agitator is
moving.
[] Do not install or store the washer where it will be exposed to
the weather.
[] Do not tamper with controls.
[] Do not repair or replace any part of the washer or attempt any
servicing unless specifically recommended in this manual or in
published user-repair instructions that you understand and
have the skills to carry out.
[] See "Electrical Requirements" for grounding instructions.
this time.
SAVE THESE INSTRUCTIONS
INSTALLATION REQUIREMENTS
Gather the required tools and parts before starting installation.
The parts supplied are in the washer basket.
Tools needed for connecting the drain hose and water
inlet hoses:
Pliersthat open to 19/16'' Flashlight (optional)
(3.95 cm)
Parts supplied:
Alternate Parts
Parts listed are available from your local Sears store or Sears
Service Center. For further information, call 1-800-4-MY-HOME ®
(1-800-469-4663}.
If You Have: You Will Need to Buy:
Laundry tub or Sump pump system (if not already
standpipe taller available)
than 96" (2.4 m)
B C
D
A. Drain hose form
B. Water inlet hoses (2)
C. Flat water inlet hose washers (4)
D. Beaded tie strap
1" (2.5 cm)
diameter standpipe
2" (5 cm) diameter to 1" (2.5 cm)
diameter standpipe adapter,
Part Number 3363920 and connector kit
Part Number 285835
Overhead sewer
Standard 20 gal. (76 L) 39" (99 cm) tall
drain tub or utility sink, sump pump and
connectors (available from local
plumbing suppliers)
Floor drain Siphon break, Part Number 285834;
additional drain hose,
Part Number 8318155 and connector kit,
Part Number 285835
Water faucets 2 longer water fill hoses:
beyond reach of fill 6 ft (1.8 m) Part Number 76314,
hoses 10 ft (3.0 m) Part Number 350008
Lint clogged drain Drain protector, Part Number 367031
Tools needed for securing the drain hose and leveling
the washer:
Adjustable or open end Wood block
wrench 9_6"(14 mm) Ruler or measuring tape
Level
Selectingtheproperlocationforyourwasherimproves
performanceandminimizesnoiseandpossiblewasher"wall<."
Yourwashercanbeinstalledinabasement,laundryroom,
closet,orrecessedarea.See"DrainSystem."
IMPORTANT:Donotinstallorstorethewasherwhereitwillbe
exposedtotheweather.
Properinstallationisyourresponsibility,
Youwillneed:
Awaterheatersettodeliver120°F(49°C)watertothe
washer.
Agroundedelectricaloutletlocatedwithin4ft(1.2m)of
wherethepowercordisattachedtothebackofthewasher.
See"ElectricalRequirements."
Hotandcoldwaterfaucetslocatedwithin3ft(90cm)ofthe
hotandcoldwaterfillvalves,andwaterpressureof
20-100psi(138-690kPa)forbestperformance.
Alevelfloorwithamaximumslopeof1"(2.5cm)underentire
washer.Installingthewasheroncarpetingisnot
recommended.
Asturdyfloortosupportthewasherweight(washer,water
andload)of315Ibs(143kgs).
Donotstoreoroperateyourwasherintemperaturesatorbelow
32°F(0°C).Somewatercanremaininthewasherandcancause
damageinlowtemperatures.See"WasherCare"forwinterizing
information.
Installation spacing for recessed area and closet
installations
The following spacing dimensions are recommended for this
washer. This washer has been tested for installation with spacing
of 0" (0 cm) clearance on the sides. Recommended spacing
should be considered for the following reasons:
Additional spacing should be considered for ease of
installation and servicing.
Additional spacing should be considered on all sides of the
washer to reduce noise transfer.
For closet installation with a door, minimum ventilation
openings in the top and bottom of the door are required.
Louvered doors with equivalent ventilation openings are
acceptable.
Companion appliance spacing should also be considered.
n
olo
_8 in_*
(310 cm 2)" _
,2,
241n. ..__
1153cm2)
1"_ ._27,/_"m-_-__1"_ 1"*_27"÷i 3"---1÷
(2.5 cm) (69.9 crn} (2,5 cm)(2.5 crn)(66.6 crn) (12,7 cm)
A B
J[_ 3"*
(7.6crn)
A. Front view
B. Side view
C. Closet door with vents
*Required spacing
The washer can be installed using the standpipe drain system
(floor or wall), the laundry tub drain system, or the floor drain
system. Select the drain hose installation method you need. See
"Tools and Parts."
Standpipe drain system--wall or floor (views A & B)
The standpipe drain requires a minimum diameter standpipe of
2" (5 cm). The minimum carry-away capacity can be no less than
17 gal. (64 L) per minute. A 2" (5 cm) diameter to 1" (2.5 cm)
diameter standpipe adapter kit is available. See "Tools and
Parts."
The top of the standpipe must be at least 39" (99 cm) high and no
higher than 96" (244 cm) from the bottom of the washer.
39"
(99 cm)
Laundry tub drain system (view C)
The laundry tub needs a minimum 20 gal. (76 L) capacity. The top
of the laundry tub must be at least 39" (99 cm) above the floor
and no higher than 96" (244 cm) from the bottom of the washer.
Floor drain system (view D)
The floor drain system requires a siphon break that may be
purchased separately. See "Tools and Parts."
The siphon break must be a minimum of 28" (71 cm) from the
bottom of the washer. Additional hoses might be needed.
Donotgroundtoagaspipe.
Checkwithaqualifiedelectricianifyouarenotsurethe
washerisproperlygrounded.
Donothaveafuseintheneutralorgroundcircuit.
ElectricalShock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical
supply is required. A time-delay fuse or circuit breaker is
recommended. It is recommended that a separate circuit
serving only this appliance be provided.
This washer is equipped with a power supply cord having a
3 prong grounding plug.
To minimize possible shock hazard, the cord must be
plugged into a mating, 3 prong, grounding-type outlet,
grounded in accordance with local codes and ordinances. If a
mating outlet is not available, it is the personal responsibility
and obligation of the customer to have the properly grounded
outlet installed by a qualified electrician.
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrician determine that the
ground path is adequate.
GROUNDING INSTRUCTIONS
For a grounded, cord=connected washer:
This washer must be grounded. In the event of a malfunction
or breakdown, grounding will reduce the risk of electrical
shock by providing a path of least resistance for electric
current. This washer is equipped with a cord having an
equipment-grounding conductor and a grounding plug. The
plug must be plugged into an appropriate outlet that is
properly installed and grounded in accordance with all local
codes and ordinances.
WARNING: Improper connection of the equipment-
grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or serviceman if you are in
doubt as to whether the appliance is properly grounded.
Do not modify the plug provided with the appliance - if it will
not fit the outlet, have a proper outlet installed by a qualified
electrician.
For a permanently connected washer:
This washer must be connected to a grounded metal,
permanent wiring system, or an equipment grounding
conductor must be run with the circuit conductors and
connected to the equipment-grounding terminal or lead on
the appliance.
INSTALLATION INSTRUCTIONS
5. Remove tape from lid. Open lid and remove foam packing
ring from washer tub. Keep foam packing ring in case you
need to move the washer in the future.
Excessive Weight Hazard
Use two or more people to move and install washer.
Failure to do so can result in back or other injury.
NOTE: To avoid floor damage during installation, set the washer
onto cardboard before moving across floor.
IMPORTANT:
Be sure the foam shipping base has been removed from the
bottom of the washer as directed in the Unpacking
Instructions.
Iffoam shipping base has not been removed, be sure lid is
secured with tape before laying washer on its back.
Removing the foam shipping base is necessary for proper
operation.
1. Place cardboard supports from shipping carton on floor
behind washer for support.
2. Using 2 or more people, tip the washer onto its back and
place on cardboard supports.
3. Remove foam shipping base.
Proper connection of the drain hose protects your floors from
damage due to water leakage. Read and follow these
instructions.
The drain hose is connected to your washer and is stored inside
the washer cabinet.
Remove drain hose from washer cabinet
Pull the corrugated drain hose out of the washer by first grabbing
the pull tie. Continue to pull the hose until the end emerges. Do
not force excess drain hose back into the rear of the washer.
4. Set washer upright.
Laundry tub drain or standpipe drain
Connecting the drain hose form to the corrugated
drain hose
A
=7
4.5"
(11.4 cm)
A. Drain hose reliefs
!. Feed end of drain hose into one end of form. Place end of drain
hose form into the drain hose relief.
2. Bend the hose over the top of the form and feed into the other end
of the form. Attach the other end of the form into the other drain
hose relief. The hose must extend 4V2" (11.4 cm) beyond the form.
To keep drain water from going back into the washer:
Do not force excess drain hose into standpipe. Hose should
be secure but loose enough to provide a gap for air.
Do not lay excess hose on the bottom of the laundry tub.
Floor drain
Do not install the drain hose form on to the corrugated drain
hose. You may need additional parts. See Floor drain under
"Tools and Parts."
Insert new flat washers (supplied) into each end of the inlet
hoses. Firmly seat the washers in the couplings.
A B
A. Coupling
B. Washer
_YAYAYA_
Connect the inlet hoses to the water faucets
Make sure the washer basket is empty.
2. Attach the hose labeled hot to the hot water faucet. Screw
on coupling by hand until it is seated on the washer.
3. Attach the hose labeled cold to the cold water faucet. Screw
on coupling by hand until it is seated on the washer.
4. Using pliers, tighten the couplings with an additional
two-thirds turn.
Tighten thecouplings with anadditional two-thirds turn.
NOTE: Do not overtighten or use tape or sealants on the
valve. Damage to the valves can result.
Clear the water lines
Run water through both faucets and inlet hoses, into a
laundry tub, drainpipe or bucket, to get rid of particles in the
water lines that might clog the inlet valve screens.
Check the temperature of the water to make sure that the hot
water hose is connected to the hot water faucet and that the
cold water hose is connected to the cold water faucet.
Connect the inlet hoses to the washer
A
A. Hot water inlet valve
B.Cold water inlet valve
1. Attach the hot water hose to the inlet valve labeled hot.
2. Attaching one hose coupling first makes it easier to tighten
the connection with pliers.
3. Screw on coupling by hand until it is seated on the washer.
4.
Using pliers, tighten the coupling with an additional
two-thirds turn.
NOTE: Do not overtighten or use tape or sealants on the
valve. Damage to the valves can result.
5.
6.
7.
Attach the cold water hose to the inlet valve labeled cold.
Screw on coupling by hand until it is seated on the washer.
Using pliers, tighten the coupling with an additional
two-thirds turn.
NOTE: Do not overtighten or use tape or sealants on the
valve. Damage to the valves can result.
Check for leaks
Turn on the water faucets and check for leaks. A small
amount of water might enter the washer. You will drain this in
a later step.
NOTE: Replace inlet hoses after 5 years of use to reduce the
risk of hose failure. Record hose installation or replacement
dates for future reference.
Ifyou connect only one water hose, you must cap off the
remaining water inlet port.
Periodically inspect and replace hoses if bulges, kinks,
cuts, wear, or leaks are found.
oe_ '_?Pe D_> M ;_!;_
1. Drape the power cord over the console.
2. Remove any cardboard used to move washer.
3.
qCP"
Beaded tie strap
Fasten the drain hose to the laundry tub leg or drain
standpipe with the beaded tie strap. See view A or B.
A
'._ i'
B C
If the washer faucets and the drain standpipe are recessed,
put the formed end of the drain hose into the standpipe.
Tightly wrap the tie strap around the water inlet hoses and the
drain hose. See view C.
Excessive Weight Hazard
Use two or more people to move and install washer.
Failure to do so can result in back or other injury.
One washer foot has been installed at a different height on your
new washer. The other three feet were preset at the factory.
Properly leveling your washer will minimize noise and vibration.
1. Slide the washer to its final location.
2. Push on upper front panel to be sure the washer is on its rear
feet.
10
Lower right front foot until it contacts the floor. By hand, firmly
rotate foot as much as an additional 11/2turns. The other three
feet have been preset at the factory.
Check the levelness of the washer by placing a level in the
crease between the top of the washer and the cabinet, first
on the front and then on the side.
1. Check the electrical requirements. Be sure that you have the
correct electrical supply and the recommended grounding
method. See "Electrical Requirements."
2. Check that all parts are now installed. If there is an extra part,
go back through the steps to see which step was skipped.
3. Check that you have all of your tools.
4. Keep the foam packing ring from the washer tub for future
relocation of the washer. Dispose of/recycle all packaging
materials.
5. Check that the water faucets are on.
6. Check for leaks around faucets and inlet hoses.
Level the front.
Level the side.
5. If the washer is not level, move the washer out slightly, tip
back, prop up the front of the washer on a wood block.
Adjust the feet up or down as necessary by twisting the feet.
Repeat steps 1 through 4 until washer is level.
6. Use a 9/16"or 14 mm open-end wrench to turn the Iocknut
counterclockwise on the foot tightly against the washer
cabinet.
IMPORTANT: If the Iocknut is not tight against the washer
cabinet, the washer may vibrate.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
7. Plug into a grounded 3 prong outlet.
8. Remove any protective film or tape remaining on the washer.
9. Read "Washer Use."
10. To test and to clean your washer, measure 1/2of the detergent
manufacturer's recommended amount of High Efficiency (HE)
powdered or liquid detergent for a medium size load and pour
it into the detergent dispenser. Close the lid. Press POWER.
Select a normal cycle and press Start. Allow it to complete
one whole cycle.
11
BENEFITS AND FEATURES
Your washer has several benefits and features that are summarized here. Some items may not apply to your model.
gentlewash TM High-Efficiency Wash System
Your new top loading, high-efficiency washer saves you time by
allowing you to do fewer, larger loads. It also conserves
resources and also lowers your water and energy bills by using
the following innovations.
Auto Water Level
This washer senses the load size and composition through a
series of fills and wash motion. It then adjusts the water level for
the best cleaning and rinsing performance. It eliminates the
guesswork. The water level is just right for every wash load size.
NOTE: You may notice during a cycle that the wash load is not
completely submerged in water. This is normal for your washer.
Auto Temperature Control (ATC)
The Auto Temperature Control (ATC) on this washer electronically
senses and maintains a uniform water temperature by regulating
incoming water temperatures. Using ATC will help dissolve
detergent.
INVIZIBLE TM Agitator
Your new washer works differently than most washers that you
are accustomed to. The most striking difference is that the
washer has an invisible agitator. It uses this new innovative
agitator at the bottom of the wash basket to move your load
through a mixture of water and detergent. The load is moved
from the outside toward the middle with items coming up in the
center and down on the outside edges.
Dispensers
The dispensers make your washer truly automatic. It is
unnecessary for you to return to the washer during the cycle to
add detergent, bleach, or fabric softener.
Laundry additives are added to the load at the proper time in the
wash cycle.
Spin Speeds
This washer is preset to automatically select the spin speed
based on the cycle selected. Depending on your wash load, you
can change the preset speeds. The spin speed on this washer is
nearly twice as fast as that of a conventional washer. You may
notice different sounds during a spin cycle because of this higher
rate of speed.
Stain Treat (CATALYST _ Cleaning Action)
The Stain Treat option helps to ensure better soil and stain
removal. Stain Treat reduces the need for pretreatment and is
safe for all fabrics. Water flushes through the dispenser to
dissolve the detergent. The detergent mixture is then sprayed
onto the load while the washer spins at low speed. This cleaning
action will last up to 5 minutes depending on the cycle selected.
The washer then stops spinning, fills with water to the
appropriate level and continues washing with the selected cycle.
High Efficiency (HE) Detergent
This washer is designed for High Efficiency (HE) detergent use
only. HE detergents are made to produce the right amount of
suds and give the best performance in low water wash systems.
Innovative Features
Your new washer includes these features that help to reduce
noise, increase the ease of use and improve wash performance.
Electronic Controls
Electronic controls with preset cycles are easy to use whether
you are a beginner or an "expert."
Quiet Operation
This washer is insulated with sound-dampening materials to
reduce washer operation sounds and noises. On some models,
an additional tub wrap is added for superior vibration- and
sound-dampening.
Suspension System
To reduce washer "walk" and "out of balance" conditions, your
new washer combines:
4 Spring damper struts to isolate vibration
Balance ring at the top and bottom of the wash basket to
minimize vibration
Operating software designed to sense and correct off-
balance loads
Clean Washer Cycle
This washer features an easy-to-use Clean Washer cycle that
thoroughly cleans the inside of your washing machine using
higher water volumes in combination with liquid chlorine bleach.
Stainless Steel Basket
The stainless steel basket is corrosion resistant and enables
higher spin speeds for more water extraction, reducing drying
time.
Force Filter Wash/Rinse System
This washer filters 100% of the wash and rinse water. The water
is filtered then recirculated. The force filter traps sand and dirt,
flushing them down the drain, so they are not redeposited onto
the clean clothes.
Save Energy Plus Option
The Save Energy Plus option allows you to increase your energy
savings on the higher temperature cycles (Whitest Whites and
Heavy Duty) while maintaining cleaning performance by
lengthening the wash time by only approximately 5 minutes.
Delay Start
Delay Start allows you to load your washer and pause the start of
the cycle for up to 13 hours.
End of Cycle Signal
The End of Cycle Signal produces an audible sound when the
wash cycle is finished. This signal is helpful when you are
removing items from the washer as soon as it stops.
12
WASHER USE
STATUS
Add AGarment
Soak/ Prewash
ClothesClean
LidLock0
NOTE: Your washer model may vary from the model shown.
Fire Hazard
Never place items in the washer that are dampened
with gasoline or ether flammable fluids°
No washer can completely remove oi.
Do not dry anything that has ever had any type of oil on
it (including cooking oils).
Doing so can reeuff in death, explosion, or fire.
WARNING: To reduce the risk of fire, electric shock, or injury to
persons, read the IMPORTANT SAFETY INSTRUCTIONS before
operating this appliance.
The following is a guide to starting your washer. Periodic
references to other sections of this manual provide more detailed
information.
Use only High Efficiency (HE) detergents. The package for this
type of detergent will be marked "HE" or "High Efficiency," HE
detergents such as TIDE ®HE are made to produce the right
amount of suds for the best performance in low water wash
systems, Follow the detergent manufacturer's instructions to
determine the correct amount of detergent to use. Your washer's
new wash system will create too much sudsing if regular non-HE
detergent is used. Using regular detergent will likely result in
washer errors, longer cycle times and reduced rinsing
performance.
MODIFIERS
AutoTeml)Control
ii
Warm/Warm
d;:;:
ii
Med Light Low Cool/ Cold
Light NoSpin Cold/Cold
Soil Spin Wash / Rinse
Level Speed Ternp
ADJUSTS
WASHTIll
OPTIONS
Save Energy Plus
2nd Rinse
Stain Treat
Auto Soak
Prewash
Loud
Soft
Cycle Signal Volume
It may also result in component failures and noticeable mold or
mildew. Use of regular (non-HE) detergent will void your
warranty. See "Warranty."
Use only "HE" High Efficiency detergent.
Place a load of sorted clothes into the washer. See "Laundry
Tips."
Load evenly to maintain washer balance. Mix large and
small items.
Load only to the top of the basket as shown. Overloading
can cause poor cleaning.
Pour measured powdered or liquid High Efficiency (HE)
detergent into the detergent dispenser. Do not put detergent
directly into the wash tub or onto clothes in the washer.
13
3. Add color-safe bleach (powdered or liquid) to this dispenser,
if needed. Be sure to match powdered color-safe bleach with
powdered detergent or match liquid color-safe bleach with
liquid detergent.
4. Pour measured liquid chlorine bleach into the liquid chlorine
bleach dispenser, if needed. Bleach is automatically
dispensed at the proper time during the wash cycle.
5=
Do not overfill. Do not dilute. Do not use more than 1 cup
(250 mL) for a full load. Use less with a smaller load size.
Follow the garment and the chlorine bleach
manufacturer's directions for proper use.
To avoid spilling, use a cup with a pouring spout. Do not
let bleach splash, drip, or run down into the washer basket.
At the end of the cycle, a small amount of water may be
left in the dispenser. This is normal.
NOTE: Use only liquid chlorine bleach in this dispenser.
Pour measured liquid fabric softener into the fabric softener
dispenser, if desired.
Do not overfill. The dispenser holds 3 oz (94 mL), or a
capful of fabric softener.
The fabric softener is dispensed in the rinse cycle. If 2nd
Rinse is selected, the fabric softener will be dispensed
during the 2nd Rinse.
Do not use fabric softener dispensing balls in this washer.
Dispensing balls will not operate correctly with this
washer.
Do not spill or drip any fabric softener onto the clothes.
At the end of the cycle, a small amount of water may be
left in the dispenser. This is normal.
NOTE: Use only liquid fabric softener in this dispenser.
6. Close the washer lid.
7. Press POWER. This turns on the washer display.
8. Select a Wash Cycle. See "Cycles."
9. Adjust the Modifiers, if desired. See "Modifiers."
10. Select desired Options. See "Options."
11. Select Delay Start, if desired. See "Delay Start" in the
"Modifiers" section.
12. Press START. The wash cycle begins, and the display shows
the estimated remaining time. The lid will lock.
NOTE: If you do not press Start within 5 minutes of pressing
Power, the washer automatically shuts off.
Add A Garment
You can place additional clothing in the wash when the "Add A
Garment" status light is glowing without sacrificing wash
performance.
To add a garment or pause the washer at any time
1. Press STOP once.
2. Wait until the Lid Lock light turns off, then open the lid.
3. Add items.
To restart the washer
1. Close the lid and press START.
2. To unlock the lid after the Add A Garment period, press STOP
once. Pressing STOP twice will cancel the wash cycle.
You can stop the wash cycle and drain the tub by pressing the
Stop button twice or the Power button once.
You can change Cycles, Modifiers and Options anytime before
Start is pressed. Not all Modifiers and Options are available for all
cycles.
A short tone sounds when a change is selected.
Three short tones sound if an unavailable combination is
selected. The last selection will not be accepted.
Changing Cycles during the wash cycle
1. Press STOP twice to cancel the cycle. The washer will drain.
2. Press POWER.
3. Select the desired wash cycle.
4. Select the desired Modifiers and Options.
5. Press START.
The washer restarts at the beginning of the new cycle.
NOTE: If you do not press Start within 5 minutes of pausing the
washer, the washer automatically shuts off.
Changing Modifiers and Options during the wash cycle
You can change a Modifier or Option anytime before the selected
Modifier or Option begins. You must:
1. Press STOP once.
2. Select the desired Modifiers and/or Options.
3. Press START.
To manually drain the washer and spin the load
1. Press STOP twice to cancel the wash cycle and drain the
washer.
2. Press POWER.
3. Press DRAIN & SPIN.
4. Press START.
When the spin is complete, the lid unlocks. Items can be
removed from the washer.
14
These lights show which portion of the cycle the washer is
operating. They also indicate when you can add other garments
to the wash load.
STATUS
AdoA Oa_mrmt
Soak / Pmwash
Was["
Srsn
CJothesClean
LidL0ek
Clothes Clean
The Clothes Clean light stays on until the lid is opened or the
Stop or Power button is pressed.
Lid Lock
When the Lid Lock status light glows, the washer lid is locked.
NOTE: You must wait until the Lid Lock light turns off before the
lid can be opened.
Indicator lights
An indicator light shows which Cycle, Modifiers and Options you
have selected.
Estimated Time Remaining
Cycle time in minutes will appear in the display while you are
making selections. The total cycle time will appear, including an
estimated time for drain and fill times, once Start is pressed.
NOTES:
The time is an estimation only and may vary depending on
load size, cycle, modifiers and options selected.
You may notice the time adjusting during the cycle. This is
normal.
The cycle time may be extended if oversudsing occurs or the
load is unbalanced.
Turn the knob to choose the right wash cycle for the type of
fabrics you are washing. When the knob points to a cycle, the
indicator light for the cycle will glow. If the default settings for the
Modifiers and Options are suitable for your wash load, you may
press Start to begin the wash cycle.
Casual/ Express
Wrinkle Free Wash
Normal Bulky /
- Bedding
Heav
Duty ToweUs
Whitest Darks /
=
Whites DeUieate / Colors
Handwash
Preset Cycle Settings
For ease of use, preset cycle settings provide the recommended
fabric care settings for each cycle.
To use the preset cycle settings:
1. Press POWER.
2. Select the cycle you want by turning the knob. The preset
cycle settings will be displayed (see following chart).
NOTE: The preset cycle times may vary slightly depending on
your model.
3. Press START. The wash cycle will begin.
Preset Cycle Settings
Cycle Preset Soil Level* Wash/Rinse
Minutes Temp _
Whitest Whites 79 Heavy Hot/Cold
(No ATC)
Heavy Duty 74 Heavy Hot/Cold
(No ATC)
Normal 43 Normal Warm/Cold
Casual/Wrinkle Free 44 Medium Warm/Cold
Light
Express Wash 34 Light Warm/Warm
Bulky/Bedding 46 Normal Warm/Cold
Sheets/Towels 46 Normal Warm/Cold
Darks/Oolors 42 Normal Cool/Cold
Delicate/Handwash 35 Light Cool/Cold
Rinse & Spin 20 Not Cold/Cold
applicable
Drain & Spin 10 Not Not
applicable applicable
Clean Washer 60 Not Not
applicable applicable
*Cycle time in minutes will appear in the display while you are
making selections. The total cycle time will appear, including an
estimated time for drain and fill times, once Start is pressed.
NOTE: Load only to the top of the basket. Overloading can cause
poor cleaning. See "Starting Your Washer."
15
Whitest Whites
This cycle introduces liquid chlorine bleach to the load at the
proper time for improved whitening of your heavily soiled white
fabrics. Cycle combines high-speed wash action and high-speed
spin. The default option setting for this cycle is 2nd Rinse to
thoroughly remove detergent and bleach. For maximum soil and
stain removal, liquid chlorine bleach should be used.
Heavy Duty
Use this cycle for heavily soiled cotton or sturdy items. Cycle
combines high-speed wash action and high-speed spin. Stain
Treat is the default option for this cycle, but it may be turned off.
See "Changing Cycles, Modifiers and Options."
Normal
Use this cycle for normally soiled cottons and mixed fabric loads.
Cycle combines high-speed wash action and high-speed spin.
Casual/Wrinkle Free
Use this cycle to wash loads of no-iron fabrics such as sport
shirts, blouses, casual business clothes, permanent press and
blends. This cycle uses medium-speed wash action, a medium-
speed spin and a cool down process to reduce wrinkling.
Express Wash
Use this cycle to wash a few lightly soiled items that are needed
in a hurry. This short cycle combines high-speed wash action and
high-speed spin for the best cleaning and shortened dry times.
Bulky/Bedding
This cycle is designed for oversized items that do not easily
absorb water, such as comforters, pillows and poly-filled jackets.
This cycle gently washes these nonabsorbent items in a preset
water level to avoid damage. This cycle starts with a soak to
thoroughly saturate your large item. This is followed by medium
wash action and medium spin speeds to maintain load balance.
NOTE: Due to the preset water level, using this cycle for items
other than those described above will create an unbalanced load.
Sheets/Towels
Use this cycle for sheets, pillowcases and towels. The wash
action of this cycle is designed to help keep large items from
tangling and bailing up.
IMPORTANT: For best performance, drop items in loose heaps
evenly around the basket wall. Do not load items directly on the
impeller for this cycle.
Darks/Colore
Use this cycle for dark or highly dyed natural fabrics such as
jeans or other cotton items that may be susceptible to dye loss.
This cycle uses low to medium-speed wash action and high-
speed spin. For best results use cold or warm water.
Delicate/Handwash
Use this cycle to wash lightly soiled special care garments or for
items labeled as "Machine Washable Wool or Silk." (Check label
instructions to make sure that the garment is washable.) This
cycle uses intermittent-low speed wash action and low-speed
spin for the gentlest fabric care with less wrinkling.
Garments are labeled "Nandwash" because:
The fiber construction may be sensitive to wash action.
The fabric contains sensitive dyes that may bleed.
NOTE: Some "Handwash" items naturally shrink when washed.
Keep this in mind when you purchase items labeled "Handwash."
Items that shrink should be dried flat. When these items are still
wet, "block" them by gently stretching to the original
measurements.
Rinse/Drain & Spin
The Rinse & Spin and Drain & Spin cycles are selected with the
same button.
©
Rinse/Drain & Spin
Rinse & Spin
This option performs a rinse only followed by a high-speed spin.
The time display will include an estimate of how long it will take to
fill and drain the washer.
When to use Rinse & Spin:
For loads that need rinsing only.
For completing a cycle after the power has been off.
To
1.
use Rinse & Spin setting:
Press RINSE/DRAIN & SPIN button once. The Rinse & Spin
indicator light, along with the Spin Speed, Water Temperature
and 2nd Rinse lights will glow. You may change the Spin
Speed and Water Temperature modifiers only.
NOTE: A Rinse & Spin cycle time of approximately
20 minutes will appear in the Estimated Time Remaining
display.
2. Press START.
Drain & Spin
An extra drain and spin may help shorten drying times for some
heavy fabrics or special-care items. Drain & Spin may also be
used for draining the washer after canceling a cycle or
completing a cycle after a power failure.
To use Drain & Spin setting:
1. Press RINSE/DRAIN & SPIN button once. The Rinse & Spin
indicator light, along with the Spin Speed, Water Temperature
and 2nd Rinse lights will glow. You may change the Spin
Speed modifier only.
2. Press 2nd RINSE to deselect Rinse & Spin. The 2nd Rinse
and Water Temperature lights will shut off to indicate that a
Drain & Spin cycle has been selected.
NOTE: A Drain & Spin time of approximately 10 minutes will
appear in the Estimated Time Remaining display.
3. Press START.
IMPORTANT: Water will dispense in the washer for a
moment, the lid will unlock, lock again, and then the Drain &
Spin cycle will continue. This is normal.
Clean Washer
Use the Clean Washer cycle once a month to keep the inside of
your washer fresh and clean. This cycle uses a higher water level
in combination with liquid chlorine bleach to thoroughly clean the
inside of your washing machine. See "Cleaning Your Washer."
©
CleanWasher
USE8LEACH ONLY
IMPORTANT: Do not add detergent to this cleaning cycle. Use
only liquid chlorine bleach. Do not place garments or other items
in the washer during the Clean Washer cycle. Use this cycle with
an empty wash tub.
16
Modifiers allow you to further customize your cycles and save energy.
Soil Level (Wash Time)
Soil level is preset for each cycle. See "Preset Cycle Settings" in
"Cycles." As you press the Soil Level pad, the cycle time
(minutes) will increase or decrease in the Estimated Time
Remaining display. To get the minimum wash time, press the pad
until the indicator light next to Light illuminates. This is the
shortest wash time available for that cycle.
HaW
I_@dHeavy
Temperature Guide
Wash Water Temperature Suggested Fabrics
Hot Whites and pastels
Warm Bright colors
Cold Darker colors that bleed or fade
NOTE: In wash water temperatures colder than 60°F (15.6°C),
detergents do not dissolve well. Soils may be difficult to remove.
))
))
li@t
Sol
ILeve)
ADJlS_
For most loads, use the time recommended in the preset
cycle settings.
For heavy soil and sturdy fabrics, press Soil Level to select
more wash time, if needed.
For light soil and delicate fabrics, press Soil Level to select
less wash time, if needed.
Spin Speed
This washer automatically selects the spin speed based on the
cycle selected. The preset speeds can be changed. Spin speeds
may vary by cycle.
High
Low
NoSpin
Spin
Speed
Wash/Rinse Temp
Select a water temperature based on the type of load you are
washing. Use the warmest wash water safe for fabrics. Follow
garment label instructions.
Warm rinses leave the loads drier and more comfortable to
handle. However, warm rinses may increase wrinkling. Cold
rinses may help with wrinkling and save energy.
AL£O bt7_r_Control
/Cold
CoJd/ C01d
Auto Temp Control
Auto Temp Control (ATC) electronically senses and maintains a
uniform wash and rinse water temperature. ATC regulates
incoming hot and cold water. The ATC is automatically turned On
when a cycle is selected. (See "Preset Cycle Settings" in
"Cycles.")
ATC is available with Warm/Warm, Warm/Cold and Cool/Cold
settings. The water temperature in the Hot/Cold and Cold/Cold
settings depend on the water temperature at the water inlet
faucets.
ATC ensures consistent cleaning.
Heated water consumes the largest amount of energy that a
washer uses.
Today's detergents work well at temperatures above 60°F
(15.6°C).
Delay Start
You can use the Delay Start feature to delay the start of a wash
cycle for up to 13 hours (depending on your model).
1. Load the washer and fill the dispensers.
2. Close the washer lid.
3. Press POWER.
4. Select the desired Cycle, Modifiers and Options.
5. Press DELAY START. 1H (one hour) will be displayed in the
time display window. The indicator light for Delay Start will
glow.
©
Delay S_art
6.
7.
For a longer delay time, press Delay Start. The Start time will
increase by 1-hour steps.
Press START. The countdown to the wash cycle will show in
the time display window, and the Delay Start indicator light
will begin to flash.
NOTE: The Start indicator light will not flash when Delay Start
is chosen. You must press Start to initiate a countdown for
the cycle to begin.
To change the Delay Start time:
Press STOR
Press DELAY START to select the desired delay time.
Press START to begin the countdown.
To cancel Delay Start:
Press START again to begin the cycle right away, or press
STOP twice to cancel the cycle.
17
Use these pads to select the desired options for your wash cycle.
OPTIONS
Saw_ EnergyPlus
2nd R_me
Stain Treat
Save Energy Plus
The Save Energy Plus option reduces wash and rinse water
temperatures to save energy while adding about 5 minutes of
wash time to maintain performance. This option must be selected
prior to the start of the cycle. The Save Energy Plus option is
available in only the Heavy Duty and Whitest Whites cycles.
2nd Rinse
A 2nd rinse can be used to aid in the removal of detergent or
bleach residue from garments. This option provides an additional
rinse with the same water temperature as the first rinse. This is
the default rinse setting for the Whitest Whites cycle. Fabric
softener will be dispensed during the 2nd Rinse.
®
Stain Treat (Catalyst Cleaning Action)
This option provides enhanced cleaning action for tough stains.
The Heavy Duty cycle automatically includes Stain Treat.
Choosing Stain Treat will add approximately 5 minutes to a cycle.
Stain Treat should be started on a dry load only and should not
be selected after the tub has started filling with water.
Stain Treat may be selected as an option with other cycles. See
table for details.
Cycle Stain Treat
(Adds time to the wash cycle)
Whitest Whites Option
Heavy Duty Default
Normal Option
Casual/Wrinkle Free Option
Express Wash Option
Bulky/Bedding Not available
Sheets/Towels Not available
Darks/Colors Option
Delicate/Handwash Option
Auto Soak/Prewash
Use these options for set-in stains and soils that need extra time
for removal. Press the Option button for Auto SoaWPrewash until
your desired choice is lighted.
When Auto Soak is selected, the washer saturates the load
with water and detergent then pauses to allow the detergent
to work on soils. The pause is followed by a slow-speed spin.
The washer pauses and spins six times before advancing to
the desired wash cycle. Auto Soak adds approximately
12 minutes to the wash cycle.
When Prewash is selected, the washer fills to the desired
water level. It then alternates between 1 minute of wash
action and a 1-minute pause period three consecutive times
with an extended pause to end the cycle. When Prewash is
complete, the washer advances to the selected wash cycle.
The Prewash option extends your wash time by
approximately 11 minutes.
Cycle Signal Volume
The End of Cycle Signal produces an audible sound when the
wash cycle is finished. This signal is helpful when you are
removing items from the washer as soon as it stops. Select Loud
or Soft. The End of Cycle Signal is off when neither option is lit.
013@_gilI¢I_i] _"+'='°'" 'e'__<'.
Power
Press POWER to turn the washer on or off.
Power
®
Start
Press START to start your washer after a cycle has been
selected. Be sure all desired Modifiers and Options have been
selected. The lid must be closed for the washer to start.
::i:2....
Stop
Press STOP once to pause or stop the washer at any time. Press
START to continue the cycle. Press STOP twice to turn off the
washer. Press STOP once to unlock the lid and add a garment.
Your new washer may make sounds your old one didn't. Because
the sounds might be unfamiliar, you may be concerned about
them. These sounds may be normal.
During washing
If you select the Stain Treat option, you will hear a spin/spray
noise at the start of the cycle.
During drain
If water is drained quickly from your washer (depending on your
installation), you may hear air being pulled through the pump
during the end of draining.
During wash and spin
This washer does not have a transmission. The motor provides
direct drive for wash and spin. You will hear sounds that are
different from those of a conventional washer.
18
LAUNDRY TIPS
Preparing clothes for washing
Follow these recommendations to help you prolong the life of
your garments.
Always use High Efficiency (HE) detergent, The package for
this type of detergent will be marked "HE" or "High
Efficiency." This wash system, along with less water, will
create too much sudsing with a regular non-HE detergent,
Using regular detergent will likely result in washer errors,
longer cycle times and reduced rinsing performance, It may
also result in component failures and noticeable mold or
mildew. HE detergents such as TIDE ®HE are made to
produce the right amount of suds for the best performance.
Follow the detergent manufacturer's instructions to
determine the amount of detergent to use.
Tie strings and sashes so they will not tangle.
Mend tears, loose hems, and seams.
Treat spots and stains.
Stained or wet garments should be washed promptly for best
results.
Sorting
Separate heavily soiled items from lightly soiled ones, even if
they would normally be washed together. Separate lint-givers
(towels, chenille) from lint-takers (corduroy, synthetics,
permanent press). When possible, turn lint-givers inside-out.
Separate dark colors from light colors, colorfast items from
noncolorfast items.
Sort by fabric and construction (sturdy cottons, knits, delicate
items).
Close zippers, snaps, and hooks to avoid snagging other
items. Remove pins, buckles, and other hard objects to avoid
scratching the washer interior. Remove non-washable trim
and ornaments.
Empty pockets and turn them inside-out.
Turn down cuffs; brush away lint and dirt.
Turn synthetic knits inside-out to avoid pilling.
Separate bulky, nonabsorbent items such as comforters,
pillows and poly-filled jackets. Use the Bulky/Bedding cycle
for these items.
Separate sheets, pillowcases and towels and use the
Sheets/Towels cycle for these items. For best performance,
drop items in loose heaps evenly around the basket wall and
do not load items directly on the impeller for this cycle.
Unloading
Remove clothes from washer after the cycle is completed.
Metal objects such as zippers, snaps, and buckles may rust if
left in the washer basket for a long time.
WASHER CARE
Washer Maintenance Procedure
This washer has a special cycle that uses higher water volumes in
combination with liquid chlorine bleach to thoroughly clean the
inside of the washing machine.
NOTES:
Read these instructions completely before beginning the
cleaning process,
It is recommended that you allow the cleanout cycle to
complete without interruptions. If necessary, the cleanout
cycle may be interrupted by pressing the Power button once
or the Stop button twice.
IMPORTANT: If the cleanout cycle is interrupted, run a Rinse
& Spin cycle to ensure that all remaining bleach is rinsed from
the washer.
Begin procedure
1. Open the washer lid and remove any items from the washer.
2. Add liquid chlorine bleach to the bleach dispenser.
Add 1 cup (250 mL) liquid chlorine bleach to the bleach
dispenser.
NOTE: Do not add any detergent to this cleaning cycle.
Use of more than 1 cup (250 mL) of bleach will cause
product damage over time.
3. Close the lid.
4. Press POWER.
5. Press CLEAN WASHER.
The Estimated Time Remaining display will show
approximately 60 minutes.
6. Press START.
The cycle will begin and water will dispense in the washer for
a moment and pause, then the lid will lock and the cycle will
continue.
Once the cleaning cycle has begun, allow the cycle to
complete. An estimated cycle time will appear on the display.
If the procedure does not sufficiently improve the machine
freshness, evaluate your installation and usage conditions for
other causes.
Always do the following to maintain washer freshness
Use only High Efficiency (HE)detergent.
Cleaning the exterior
Use a soft damp cloth or sponge to wipe up any spills.
Occasionally wipe the outside of your washer to keep it looking
new, Use mild soap and water. Do not use abrasive products.
19
Replace inlet hoses after 5 years of use to reduce the risk of hose
failure. Periodically inspect and replace inlet hoses if bulges,
kinks, cuts, wear or leaks are found.
When replacing your inlet hoses, mark the date of replacement
on the label with a permanent marker.
Install and store your washer where it will not freeze. Because
some water may stay in the hoses, freezing can damage your
washer. If storing or moving your washer during freezing weather,
winterize it.
Non-use or vacation care:
Operate your washer only when you are at home. If you will be on
vacation or not using your washer for an extended period of time,
you should:
Unplug washer or disconnect power.
Turn off the water supply to the washer. This helps avoid
accidental flooding (due to a water pressure surge) while you
are away.
To winterize washer:
1. Shut off both water faucets.
2. Disconnect and drain water inlet hoses.
3. Put 1 qt (1 L) of R.V.-type antifreeze in the basket.
4. Run washer on the Rinse & Spin setting for about 30 seconds
to mix the antifreeze and remaining water.
5. Unplug washer or disconnect power.
To use washer again:
1. Flush water pipes and hoses. Reconnect water inlet hoses.
Turn on both water faucets.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter,
Do not use an extension cord.
Failure to fellow these instructions can result in death,
fire, or electrical shock.
2.
3.
Plug in washer or reconnect power.
Run the washer through the Bulky/Bedding cycle to clean the
washer and remove the antifreeze, if used. Use only High
Efficiency (HE) detergent. Use 1/2the manufacturer's
recommended amount for a medium-sized load.
To transport the washer:
1. Shut off both water faucets.
2. Disconnect and drain water inlet hoses.
3. If the washer will be moved during freezing weather, put 1 qt
(1 L) of R.V.-type antifreeze in the basket. Run washer on the
Rinse & Spin setting for about 30 seconds to mix the
antifreeze and remaining water.
4. Disconnect the drain from the drain system.
5. Unplug the power cord,
6. Place the inlet hoses into the basket.
7. Drape the power cord and drain hose over edge into the
basket.
8. Place foam packing ring from the original shipping materials
in the top of washer. If you do not have the original foam
packing ring, place heavy blankets, towels, etc. into basket
opening. Close the lid and put apiece of tape over the lid and
down to the front of the washer.
Reinstalling the washer
1. Follow the "Installation Instructions" to locate, level and
connect the washer.
2. Run the washer through the Bulky/Bedding cycle to clean the
washer and remove the antifreeze, if used. Use only High
Efficiency (HE) detergent. Use 1/2the manufacturer's
recommended amount for a medium-sized load.
2O
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76

Kenmore 11027092603 Le manuel du propriétaire

Catégorie
Machines à laver
Taper
Le manuel du propriétaire