Kenmore 1101820296 Le manuel du propriétaire

Marque: Kenmore

Modèle: 1101820296

Catégorie: Machines à laver

Taper: Le manuel du propriétaire

24" (61 cm) Wide

LAUNDRY CENTER

Washer - Electric Dryer

ENSEMBLE DE BUANDERIE

de 24" (61 cm) de largeur

Laveuse - S_cheuse _lectrique

Models/Mod61es 11 0.C18202

W10035020 Sears Canada Inc., Toronto, Ontario, Canada M5B 2B8 www.sears.ca

TABLEOF CONTENTS

MAINTENANCE AGREEMENTS .................................................... 2

WARRANTY ..................................................................................... 3

WASHER/DRYER SAFETY ............................................................ 4

INSTALLATION INSTRUCTIONS .................................................. 5

Tools and Parts ............................................................................ 5

Alternate Parts .............................................................................. 5

Location Requirements ................................................................ 6

Drain System ................................................................................ 7

Electrical Requirements ................................................................ 7

Venting Requirements .................................................................. 8

Install Leveling Legs ..................................................................... 9

Remove Foam Packing ................................................................ 9

Connect Drain Hose ..................................................................... 9

Connect Inlet Hoses .................................................................. 10

Secure Drain Hose .................................................................... 11

Plan Vent System ...................................................................... 11

Install Vent System .................................................................... 12

Level Laundry Center ................................................................ 12

Connect Vent ............................................................................. 13

Complete Installation ................................................................. 13

WASHER USE .............................................................................. 14

Starting Your Washer ................................................................ 14

Cycles ........................................................................................ 15

Rinse and Spin .......................................................................... 15

Drain and Spin ........................................................................... 15

Understanding Washer Cycles .................................................. 15

Normal Sounds .......................................................................... 16

LAUNDRY TIPS ............................................................................ 18

Loading ...................................................................................... 16

DRYER USE ................................................................................. 17

Starting Your Dryer .................................................................... 17

Stopping and Restarting ........................................................... 17

Loading ...................................................................................... 17

Drying, Cycle and Temperature Tips ........................................ 18

Cycles ........................................................................................ 18

LAUNDRY CENTER CARE ......................................................... 19

Cleaning the Laundry Center Location ..................................... 19

Cleaning Your Washer ............................................................... 19

Water Inlet Hoses ...................................................................... 19

Cleaning the Lint Screen ........................................................... 19

Cleaning the Dryer Interior ........................................................ 20

Removing Accumulated Lint ..................................................... 20

Vacation, Storage and Moving Care ......................................... 20

TROUBLESHOOTING WASHER ................................................ 21

TROUBLESHOOTING DRYER .................................................... 23

MAINTENANCE

AGREEMENTS

Maintenance Agreements

Your purchase has added value because you can depend on

Sears HomeCentraP for service. With over 2,400 Service

Technicians and more than a million parts and accessories, we

have the tools, parts, knowledge and skills to back our pledge:

We Service What We Sell.

Your Kenmore ®product is designed, manufactured and tested to

provide years of dependable operation. But like all products, it

may require service from time to time. The Sears Maintenance

Agreement offers you an outstanding service program, affordably

priced.

The Sears Maintenance Agreement

• Is your way to buy tomorrow's service at today's price

• Eliminates repair bills resulting from normal wear and tear

• Provides phone support from a Sears technician on products

requiring in-home repair

• Even if you don't need repairs, provides an annual Preventive

Maintenance Check, at your request, to ensure that your

product is in proper running condition.

Some limitations apply. For more information about Sears

Canada Maintenance Agreements, call 1-800-381-6865.

KENMORE APPLIANCE WARRANTY

ONE YEAR LIMITED WARRANTY

When installed, operated and maintained according to all

instructions supplied with the product, if this appliance fails due

to a defect in material or workmanship within one year from the

date of purchase, call 1-800-4-MY-HOME ®to arrange for free

repair.

If this appliance is used for other than private family purposes,

this warranty applies for only 90 days from the date of purchase.

THIS WARRANTY COVERS ONLY DEFECTS IN MATERIAL

AND WORKMANSHIP. SEARS WILL NOT PAY FOR:

1. Expendable items that can wear out from normal use,

including but not limited to filters, belts, light bulbs, and bags.

2. A service technician to instruct the user in correct product

installation, operation or maintenance.

3. A service technician to clean or maintain this product.

4. Damage to or failure of this product if it is not installed,

operated or maintained according to all instructions supplied

with the product.

5. Damage to or failure of this product resulting from accident,

abuse, misuse or use for other than its intended purpose.

6. Damage to or failure of this product caused by the use of

detergents, cleaners, chemicals or utensils other than those

recommended in all instructions supplied with the product.

7. Damage to or failure of parts or systems resulting from

unauthorized modifications made to this product.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF

REMEDIES

Customer's sole and exclusive remedy under this limited

warranty shall be product repair as provided herein. Implied

warranties, including warranties of merchantability or fitness for a

particular purpose, are limited to one year or the shortest period

allowed by law. Sears shall not be liable for incidental or

consequential damages. Some states and provinces do not allow

the exclusion or limitation of incidental or consequential

damages, or limitations on the duration of implied warranties of

merchantability or fitness, so these exclusions or limitations may

not apply to you.

This warranty applies only while this appliance is used in the

United States and Canada.

This warranty gives you specific legal rights, and you may also

have other rights which vary from state to state.

Sears, Roebuck and Co.

Dept. 817WA, Hoffman Estates, IL 60179

Sears Canada Inc.

Toronto, Ontario, Canada M5B 2B8

PRODUCT RECORD

In the space below, record your complete model number, serial

number, and purchase date. You can find this information on the

model and serial number label located on the product.

Have this information available to help you obtain assistance or

service more quickly whenever you contact Sears concerning

your appliance.

Model number

Serial number

Purchase date

Save these instructions and your sales receipt for future

reference.

WASHER/DRYER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer/dryer, follow basic

precautions, including the following:

[] Read all instructions before using the washer/dryer.

[] Do not place items exposed to cooking oils in your dryer.

Items contaminated with cooking oils may contribute to a

chemical reaction that could cause a load to catch fire.

[] Do not wash or dry articles that have been previously

cleaned in, washed in, soaked in, or spotted with gasoline,

dry-cleaning solvents, other flammable, or explosive

substances as they give off vapors that could ignite or

explode.

[] Do not add gasoline, dry-cleaning solvents, or other

flammable, or explosive substances to the wash water.

These substances give off vapors that could ignite or

explode.

[] Do not allow children to play on or in the washer/dryer.

Close supervision of children is necessary when the

washer/dryer is used near children.

[] Before the washer/dryer is removed from service or

discarded, remove the doors to the washer/dryer

compartments.

[] Do not reach into the washer/dryer if the tub, agitator or

drum is moving.

[] Do not install or store the washer/dryer where it will be

exposed to the weather.

[] Do not tamper with controls.

[] Clean dryer lint screen before or after each load.

[] Under certain conditions, hydrogen gas may be produced in

a hot water system that has not been used for 2 weeks or

more. HYDROGEN GAS IS EXPLOSIVE. If the hot water

system has not been used for such a period, before using

the washing machine, turn on all hot water faucets and let

the water flow from each for several minutes. This will

release any accumulated hydrogen gas. As the gas is

flammable, do not smoke or use an open flame during this

time.

[] Do not repair or replace any part of the washer/dryer or

attempt any servicing unless specifically recommended in

this Use and Care Guide or in published user-repair

instructions that you understand and have the skills to carry

out.

[] Do not use fabric softeners or products to eliminate static

unless recommended by the manufacturer of the fabric

softener or product.

[] Do not use heat to dry articles containing foam rubber or

similarly textured rubber-like materials.

[] Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint, dust,

and dirt.

[] The interior of the machine and dryer exhaust vent should

be cleaned periodically by qualified service personnel.

[] See "Electrical Requirements" section for grounding

instructions.

SAVE THESE INSTRUCTIONS

INSTALLATION INSTRUCTIONS

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed:

#2 Phillips and flat-blade

screwdriver

Adjustable wrench that

opens to 1" (2.5 cm) or

9/16"open-end wrench (for

adjusting dryer feet)

1A"nut driver or socket

wrench

Tin snips (for new vent

installations)

• Caulking gun and

compound (for installing

new exhaust vent)

• Level

• Knife

• Vent clamps

• Pliers

• Scissors

• Wood block (for leveling)

• Ruler or measuring tape

Parts supplied:

Remove parts package from the washer basket. Check that all

parts were included.

B C D

E F

A. Water inlet hoses (2)

B. Inlet hose flat washers (4)

C. Rear leveling legs

D. Front leveling legs (2)

E. Plastic strap

F Drain hose

G. Yellow, single wire hose clamp

H. Silver, double-wire hose clamp

Parts needed:

Check local codes, electrical supply and venting, and read

"Electrical Requirements" and "Venting Requirements" before

purchasing parts.

Mobile home installations require metal exhaust system hardware

available for purchase from your local Sears store or Sears

Service Center. For further information, please call

1-800-4-MY-HOME ®(1-800-469-4663}.

Parts listed are available from your local Sears store or Sears

Service Center. For further information, please call

1-800-4-MY-HOME® (1-800-469-4663).

If You Have You Will Need to Buy

Laundry tub or Sump pump system (if not already

standpipe taller than available)

96" (2.4 m)

1" (2.5 cm) diameter 2" (5 cm) diameter to 1" (2.5 cm)

standpipe diameter standpipe adapter, Part

Number 3363920

Overhead sewer Standard 20 gal. (76 L) 34" (86.4 cm)

tall drain tub or utility sink and sump

pump (available from local plumbing

suppliers)

Floor drain Siphon break, Part Number 285320,

additional drain hose, Part Number

285702 and connector kit,

Part Number 285442

Drain hose too short Drain hose, Part Number 285664 and

connector kit, Part Number 285442

Lint clogged drain Drain protector, Part Number 367031

Water faucets 2 longer water fill hoses:

beyond reach of fill 6 ft (1.8 m) Part Number 76314,

hoses 10 ft (3.0 m) Part Number 350008

ExplosionHazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Failure to do so can result in death, explosion, or fire.

You will need

• A location that allows for proper exhaust installation. See

"Venting Requirements."

• A grounded electrical outlet located within 2 ft (61 cm) of

either side of the laundry center. See "Electrical

Requirements."

• A sturdy floor to support the laundry center weight (laundry

center, water and load) of 500 Ibs (226.8 kg).

A level floor with a maximum slope of 1" (2.5 cm) under entire

laundry center. Clothes may not tumble properly and

automatic sensor cycles may not operate correctly if laundry

center is not level. Installing on carpet is not recommended.

• A water heater set to deliver 120°F (49°C) water to the

washer.

• Hot and cold water faucets located within 4 ft (1.2 m) of the

hot and cold water fill valves, and water pressure of 5-100 psi

(34.5-689.6 kPa).

The laundry center must not be installed or stored in an area

where it will be exposed to water and/or weather.

Do not operate your washer in temperatures at or below •

32°F (0°C). Some water can remain in the washer and can cause

damage in low temperatures. See "Vacation, Storage and Moving •

Care" for winterizing information.

Do not operate your dryer at temperatures below 45°F (7°C). At

lower temperatures, the dryer might not shut off at the end of an

automatic cycle. This can result in longer drying times. •

Check code requirements. Some codes limit, or do not permit,

installation of the laundry center in garages, closets, mobile

homes or sleeping quarters. Contact your local building

inspector.

Installation Clearances

The location must be large enough to allow the dryer door to

open fully.

Laundry Center Dimensions

15%"

(39.05 cm)

71 ¾"

(192.25 cm)

32%"

81.6 cm)

23 T/8

(60.64 cm)

*Most installations require a minimum 51/2'' (14 cm) clearance

behind the dryer for the exhaust vent with elbow. See "Venting

Requirements."

Minimum installation spacing for recessed area or closet

installation

The following dimensions shown are for the minimum spacings

allowed.

• Additional spacing should be considered for ease of

installation and servicing.

Additional clearances might be required for wall, door and

floor moldings.

For closet installation, with a door, minimum ventilation

openings in the top and bottom of the door are required.

Louvered doors with equivalent ventilation openings are

acceptable.

Rear clearance may be 1" (2.5 cm) when house exhaust

system is lined up directly with dryer exhaust.

1" _,,-)_- 23%"-_-1" -_ 1" _e 27Y_"-_,-

(2.5cm) (60.64cm) 2.5cm 2,5cm (69.22cm)

A B

__ 1"

_. (2.5cm)i

48in.z

(3100rn2)I

24inY

(155cm=)I

_- 5½"

(14¢rn)

3" (7.6crn)

"NNN-t

__' (7.6cm)

A. Recessed area

B. Side view - closet or confined area

C. Closet door with vents

Mobile Home - Additional Installation Requirements

This laundry center is suitable for mobile home installations.

The installation must conform to the Canadian Manufactured

Home Standard, CAN/CSA-Z240 MH.

Mobile home installations require:

• Metal exhaust system hardware, which is available for

purchase from your local Sears store or Sears Service Center.

Special provisions must be made in mobile homes to

introduce outside air into the dryer. The opening (such as a

nearby window) should be at least twice as large as the dryer

exhaust opening.

The laundry center can be installed using the standpipe drain

system (floor or wall), the laundry tub drain system, or the floor

drain system. Select the drain hose installation method you need.

See "Alternate Parts."

Standpipe drain system - wall or floor (views A & B)

The standpipe drain requires a minimum diameter standpipe of •

2" (5 cm). The minimum carry-away capacity can be no less than

17 gal. (64 L) per minute. A 2" (5 cm) diameter to 1" (2.5 cm)

diameter standpipe adapter kit is available. See "Alternate Parts."

The top of the standpipe must be at least 39" (99 cm) high and no

higher than 96" (2.4 m) from the bottom of the washer. •

Laundry tub drain system (view C)

The laundry tub needs a minimum 20 gal. (76 L) capacity. The top

of the laundry tub must be at least 34" (86.4 cm) above the floor

and no higher than 96" (2.4 m) from the bottom of the washer.

Floor drain system (view D)

The floor drain system requires a siphon break that may be

purchased separately. See "Alternate Parts."

The siphon break must be a minimum of 28" (71 cm) from the

bottom of the washer. Additional hoses might be needed.

C D

E ect ca R< s 'sme sts

Electrical Shock Hazard

Plug into a grounded 4 prong outlet.

Failure to do so can result in death or electrical shock.

Itis your responsibility

• Tocontact a qualified electrical installer.

To be sure that the electrical connection is adequate and in

conformance with the Canadian Electrical Code, C22.1 -latest

edition and local codes. A copy of the above codes standard

may be obtained from: Canadian Standards Association, 178

Rexdale Blvd., Toronto, ON M9W 1R3 CANADA.

To supply the required 4 wire, single phase, 115/230 volt,

60 Hz., AC only electrical supply on a separate 30-amp

circuit, fused on both sides of the line. A time-delay fuse or

circuit breaker is recommended. Connect to an individual

branch circuit.

This dryer is equipped with a CSA International Certified

Power Cord intended to be plugged into a standard 14-30R

wall receptacle. The cord is 5 ft (1.52 m) in length. Be sure

wall receptacle is within reach of dryer's final location.

4-wire receptacle 14-30R

• Do not use an extension cord.

If using a replacement power supply cord, it is recommended

that you use Power Supply Cord Replacement Part Number

9831317. For further information, please call 1-800-4-MY-HOME ®

(1-800-469-4663).

GROUNDING INSTRUCTIONS

[] For a grounded, cord-connected washer/dryer:

This washer/dryer must be grounded. In the event of

malfunction or breakdown, grounding will reduce the risk of

electric shock by providing a path of least resistance for

electric current. This washer/dryer is equipped with a cord

having an equipment-grounding conductor and a grounding

plug. The plug must be plugged into an appropriate outlet

that is properly installed and grounded in accordance with

all local codes and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative or

personnel if you are in doubt as to whether the washer/dryer

is properly grounded. Do not modify the plug provided with

the washer/dryer: if it will not fit the outlet, have a proper

outlet installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

• Remove excess flexible metal vent to avoid sagging and

kinking that may result in reduced airflow and poor

performance.

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent.

Failure to follow these instructions can result in death

or fire.

WARNING: To reduce the risk of fire, this laundry center

MUST BE EXHAUSTED OUTDOORS.

IMPORTANT: Observe all governing codes and ordinances,

The dryer exhaust must not be connected into any gas vent,

chimney, wall, ceiling or a concealed space of a building.

If using an existing vent system

• Clean lint from the entire length of the system and make sure

exhaust hood is not plugged with lint,

• Do not install flexible metal vent in enclosed walls, ceilings or

floors.

Elbows

45° elbows provide better airflow than 90° elbows.

Good Better

Clamps

• Use clamps to seal all joints.

• Exhaust vent must not be connected or secured with screws

or other fastening devices that extend into the interior of the

duct. Do not use duct tape.

Clamp

• Replace any plastic or metal foil vent with rigid or flexible

heavy metal vent.

• Review Vent system chart. Modify existing vent system if

necessary to achieve the best drying performance.

If this is a new vent system

Vent material

• Use a heavy metal vent. Do not use plastic or metal foil vent.

• 4" (10.2 cm) heavy metal exhaust vent and clamps must be

used. DURASAFE TM venting products are recommended.

4" (!0.2 cm) heavymetal exhaust vent

DURASAFE TM vent products can be purchased from your

dealer. For further information, please call

1-800-4-MY-HOME (1-800-469-4663) orvisit our website at

www.sears.ca.

Rigid metal vent

• For best drying performance, rigid metal vents are

recommended.

• Rigid metal vent is recommended to avoid crushing and

kinking.

Flexible metal vent

• Flexible metal vents are acceptable only if accessible for

cleaning.

• Flexible metal vent must be fully extended and supported

when the laundry center is in its final position.

Exhaust

Recommended hood styles are shown here.

(10.2 cm)

A.Louvered hood style

B.Box hood style

The angled hood style (shown here) is acceptable.

An exhaust hood should cap the vent to keep rodents and

insects from entering the home.

Exhaust hood must be at least 12" (30.5 cm) from the ground

or any object that may be in the path of the exhaust (such as

flowers, rocks or bushes, snow line, etc.).

• Do not use an exhaust hood with a magnetic latch.

Improper venting can cause moisture and lint to collect

indoors, which may result in:

[] Moisture damage to woodwork, furniture, paint,

wallpaper, carpets, etc.

[] Housecleaning problems and health problems.

Excessive Weight Hazard

Use two or more people to move and install

washer/dryer.

Failure to do so can result in back or other injury.

To protect the floor, use a large flat piece of cardboard from the

shipping carton. Gently place the laundry center on its side, on

the cardboard.

Install the rear leveling legs

1. Push legs into holes in rear corners until they snap into place.

2. Check adjustability of rear legs by pushing in one leg. The

other leg should come out. Check both legs. If they do not

move freely, repeat Step 1.

Install the front leveling legs

1. Examine the front leveling legs. Find the diamond marking.

2. Screw front legs by hand, into the holes in the triangular

braces in the front corners. Use wrench to finish turning the

legs until the diamond marking is no longer visible.

3. Stand the laundry center upright.

1. Open the washer lid. The latch under the dryer will keep the

lid open.

2. Pull the foam packing ring out of the washer.

NOTE: Keep the foam ring and use it when transporting your

laundry center. This packing material is used to keep the washer

tub stable during transport.

Proper connection of the drain hose protects your floors from

damage due to water leakage, To keep the drain hose from

coming off or leaking, it must be installed according to the

following instructions:

IMPORTANT: To ensure proper installation, this procedure must

be followed exactly.

1. Check the drain hose to see whether it is the proper length.

2. Wet the inside of the straight end of the drain hose with tap

water.

IMPORTANT: Do not use any lubricant other than water.

3. Squeeze ears of the silver, double-wire clamp with pliers to

open. Place clamp over the straight end of the drain hose

_A"(6.4 mm) from the end.

Open clamp. Twist hose back and forth while pushing onto

drain connector on the side of the laundry center. Continue

until hose contacts the ribbed stops on the cabinet.

5. Place clamp over the area marked "CLAMR" Release clamp.

For laundry tub or standpipe drain systems

1. Open the yellow, single-wire clamp and slide over the hooked

end of the drain hose to secure the rubber and corrugated

sections together.

A. Hooked end

B. Drain hose

2. Put the hooked end of drain hose into laundry tub or

standpipe. Rotate hook to eliminate kinks.

To keep drain water from going back into the washer:

• Do not straighten hooked end of the drain hose and force

excess drain hose into standpipe. Hose should be secure but

loose enough to provide a gap for air.

• Do not lay excess hose on the bottom of the laundry tub.

For use with floor drain

Remove the drain hose hook from the corrugated drain hose. You

may need additional parts. See Floor drain under "Alternate

Parts."

Insert a new flat washer (supplied) into each end of the inlet

hoses. Firmly seat the washers in the couplings.

A B

A. Coupling

B.Washer

Connect the inlet hoses to the water faucets

Make sure the washer basket is empty.

2. Attach the hose labeled hot to the hot water faucet. Screw on

coupling by hand until it is seated on the washer.

3. Attach the hose labeled cold to the cold water faucet. Screw

on coupling by hand until it is seated on the washer.

4. Using pliers, tighten the couplings with an additional two-

thirds turn.

NOTE: Do not overtighten or use tape or sealants on the valve.

Damage to the valves can result.

Clear the water lines

• Run water through both faucets and inlet hoses, into a

laundry tub, drainpipe or bucket to get rid of particles in the

water lines that might clog the inlet valve screens.

• Check the temperature of the water to make sure that the hot

water hose is connected to the hot water faucet and that the

cold water hose is connected to the cold water faucet.

Connect the inlet hoses to the washer

1. Attach the hot water hose to the bottom inlet valve. Attaching

the hot water hose first makes it easier to tighten connection

with pliers.

2. Screw on coupling by hand until it is seated on the washer.

3. Using pliers, tighten the couplings with an additional two-

thirds turn.

NOTE: Do not overtighten or use tape or sealants on the valve.

Damage to the valves can result.

i ....A

A. Cold water inlet valve (top)

B. Hot water inlet valve (bottom)

4. Attach the cold water hose to the top inlet valve.

5. Screw on coupling by hand until it is seated on the washer.

6. Using pliers, tighten the couplings with an additional two-

thirds turn.

NOTE: Do not overtighten or use tape or sealants on the valve.

Damage to the valves can result.

If you are working in a closet or recessed area

Move the laundry center into its final position and remove

cardboard from under laundry center. Remove the access panel

by removing 3 Phillips-head screws and one bumper, located at

the top of the access panel. Set panel, screws and bumper aside.

Complete hookup of water hoses and (on gas models) the flexible

gas connector through the access area. Replace access panel

upon completion of laundry center installation.

Check for leaks

7. Turn on the water faucets and check for leaks. A small

amount of water might enter the washer. You will drain this

later.

NOTE: Replace inlet hoses after 5 years of use to reduce the risk

of hose failure. Record hose installation or replacement dates for

future reference.

• If you connect only one water hose, you must cap off the

remaining water inlet port.

• Periodically inspect and replace hoses if bulges, kinks, cuts,

wear or leaks are found.

• The apparatus must be connected to the water faucets using

the new hoses. Do not use old hoses.

Move the laundry center to its final location and remove any

cardboard used to move the laundry center.

Locate the plastic strap included in the parts package.

(22

Beaded tie strap

Wrap the drain hose to the laundry tub leg or standpipe with

the plastic strap (A or B below) and secure.

A B C

If the water faucets and the drain standpipe are recessed, put

the hooked end of the drain hose in the standpipe. Tightly

wrap the plastic strap around the water inlet hoses and the

drain hose (C above).

Choose your exhaust installation type

Recommended exhaust installations

Typicalinstallations vent the dryer from the rear of the washer/

dryer. Other installations are possible.

A _ ..................b

,KLN:r: E

A. Dryer

B. Rigid metal or flexible metal vent

C. Clamps

D. Wall

E. Elbow

F. Clamps

G. Elbow

H. Exhaust hood

Optional exhaust installations

This laundry center can be converted to exhaust out the right or

left side. To convert the laundry center, use Side Exhaust Kit Part

Number 279823. If your laundry center was previously exhausted

from the right or left side, it can be converted to rear exhaust by

using standard offset connections. To cover the hole in the side,

one of the following plugs can be added:

692790 (white)

3979370 (graphite)

3977784 (biscuit)

Follow the instructions in the kit to install. Kits are available from

your local Sears store or Sears Service Center.

•T•LT i

B C

A. Standard rear offset exhaust installation

B. Rear exhaust for offset close clearance connection

C. Left or right side exhaust installation

Alternate installations for close clearances

Venting systems come in many varieties. Select the type best for

your installation. Three close-clearance installations are shown.

Refer to the manufacturer's instructions provided with the vent

system.

....L-R_-IN--- ....[--A:A- -'

.........

", i ",. i

,,j......... ,,,..........

A B C

A. Loop system with standard elbows

B. Loop system with one offset and one standard elbow

C. Vent system with one periscope (2" [5 cm] clearance)

NOTE: The following kits for close clearance alternate

installations are available for purchase. To order, please call

1-800-4-MY-HOME ®(1-800-469-4663}.

Over-the-Top Installation:

Part Number 26-49900

Periscope Installation (For use with dryer vent to wall vent

mismatch):

Part Number 26-49901 - Less than 5" (12.7 cm) mismatch

Part Number 26-49908 - 5" (12.7 cm) to 18" (45.7 cm)

mismatch

Part Number 26-49904 - 18" (45.7 cm) to 29" (73.7 cm)

mismatch

Part Number 26-49905 - 29" (73.7 cm) to 50" (127 cm)

mismatch

Special provisions for mobile home installations

The exhaust vent must be securely fastened to a noncombustible

portion of the mobile home structure and must not terminate

beneath the mobile home. Terminate the exhaust vent outside.

Determine vent path

• Select the route that will provide the straightest and most

direct path outdoors.

• Plan the installation to use the fewest number of elbows and

turns.

• When using elbows or making turns, allow as much room as

possible.

• Bend vent gradually to avoid kinking.

• Use the fewest 90 °turns possible.

Determine vent length and elbows needed for best

drying performance

• Use the Vent system chart below to determine type of vent

material and hood combinations acceptable to use.

NOTE: Do not use vent runs longer than those specified in

the Vent system chart. Exhaust systems longer than those

specified will:

• Shorten the life of the dryer.

• Reduce performance, resulting in longer drying times and

increased energy usage.

The Vent system chart provides venting requirements that will

help to achieve the best drying performance.

Vent system chart

NOTE: Side exhaust installations add a 90° turn inside the

laundry center. To determine maximum exhaust length, add one

90° turn to the chart.

Number of Type of Vent Box or Angled

90° turns Louvered hoods

or elbows hoods

0 Rigid metal 43 ft (13.1 m) 36 ft (11.0 m)

Flexible metal 30 ft (9.1 m) 24 ft (7.3 m)

1 Rigid metal 33 ft (10.1 m) 26 ft (7.9 m)

Flexible metal 24 ft (7.3 m) 18 ft (5.5 m)

2 Rigid metal 24 ft (7.3 m) 16 ft (4.9 m)

Flexible metal 16 ft (4.9 m) 10 ft (3.0 m)

Install exhaust hood. Use caulking compound to seal exterior

wall opening around exhaust hood.

Connect vent to exhaust hood. Vent must fit inside exhaust

hood. Secure vent to exhaust hood with 4" (10.2 cm) clamp.

Run vent to dryer location. Use the straightest path possible.

See "Determine vent path" in "Plan Vent System." Avoid 90°

turns. Use clamps to seal all joints. Do not use duct tape,

screws or other fastening devices that extend into the interior

of the vent to secure vent.

Lew? b%,}"K Oet "tel

Properly leveling your laundry center averts excessive noise and

vibration.

1. Check the levelness of the laundry center by placing a level

on the top edge of the washer, first side to side, then front to

back.

If the laundry center is not level, prop up the front with a

wood block and adjust the feet up or down as necessary.

Remove wood block and lower laundry center. Repeat this

step until the laundry center is level.

1. Using a 4" (10.2 cm) clamp, connect vent to exhaust outlet in

laundry center. If connecting to existing vent, make sure the

vent is clean. The vent must fit over the exhaust outlet and

inside the exhaust hood. Make sure the vent is secured to

exhaust hood with a 4" (10.2 cm) clamp.

2. Move laundry center into its final position. Do not crush or

kink vent. Make sure laundry center is level.

1. Check that all parts are now installed. If there is an extra part,

go back through the steps to see which step was skipped,

2. Check that you have all of your tools.

3. Dispose of/recycle all packaging materials, Keep the plastic

foam for use if the laundry center should be transported.

4. Check the laundry center's final location. Be sure the vent is

not crushed or kinked,

5. Check that the laundry center is level and front leveling feet

are tight. See "Level Laundry Center."

6. Plug into a grounded 4 prong outlet. Turn on power.

7. Check that the water faucets are on.

8. Check for leaks around faucets and inlet hoses.

9. Remove the blue protective film on the console and any tape

remaining on the laundry center.

10. Read "Washer Use" and "Dryer Use."

11. Wipe the dryer drum interior thoroughly with a damp cloth to

remove any dust.

12. To test the washer, measure _/2the normal recommended

amount of detergent and pour it into the washer. Close the lid.

Select HEAVY DUTY and pull out the Cycle Control knob.

Allow the washer to complete one whole cycle.

13. To test the dryer, set the dryer on a full heat cycle (not an air

cycle) for 20 minutes and start the dryer.

If the dryer will not start, check the following:

14.

• Controls are set in a running or "On" position.

• Start button has been firmly pushed.

• Laundry center is plugged into a grounded outlet.

• Electrical supply is connected.

• Household fuse is intact and tight, or circuit breaker has

not tripped.

• Dryer door is closed.

When the dryer has been running for 5 minutes, open the

dryer door and feel for heat. Ifyou feel heat, cancel cycle and

close the door.

If you do not feel heat, turn off the dryer and check the

following:

• There may be 2 household fuses or circuit breakers for

the dryer. Check to make sure both fuses are intact and

tight, or that both circuit breakers have not tripped. If

there is still no heat, contact a qualified technician.

NOTE: You may notice a burning odor when dryer is first heated.

This odor is common when the heating element is first used. The

odor will go away.

WASHER USE

SPIN .........................................................................10 REGULAR

GENTLE WATERTEMP WATERLEVEL

HEAVY DUTY SHORT

RINSE PERMANENT MEDIUM

WARM WARM LOAD

SMALL LARGE

PRESS COLDWARM LL_

COLD __e • HOT LOAD_ LOAD

COLD__COLD

e RESET

SHORT 8

REGULAR10- SPIN

SUPER 12 -

SOAK_

KNiT/DELiCATE

RINSE

Fire Hazard

Never place items in the washer that are dampened

with gasoline or other flammable fluids.

No washer can completely remove oil.

Do not dry anything that has ever had any type of oil on

it (including cooking oils).

Doing so can result in death, explosion, or fire.

WARNING: To reduce the risk of fire, electric shock, or injury to

persons, read the IMPORTANT SAFETY INSTRUCTIONS before

operating this appliance.

The following is a guide to starting your washer. Periodic

references to other sections of this manual provide more detailed

information.

1. Pour measured powdered or liquid detergent into the washer.

Ifdesired, add powdered or liquid color safe bleach.

2. Place a load of sorted clothes in the washer.

• Load evenly to maintain washer balance. Mix large and

small items. See "Loading."

• Items should move easily through the wash water.

Overloading can cause poor cleaning.

Close the washer lid.

Turn the WATER LEVEL selector knob to the correct setting

for your wash load and the type of fabric being washed.

WATER LEVEL

M_OlUM

LOA_

SMALL LA_E

LOA_UlA_O o

_SF

• Choose a load size that allows the load to move freely for

best fabric care. See "Loading."

• You may change the load size selection after the washer

has started filling by turning the selector to a different

setting.

Set the WATER TEMP selector to the correct setting for the

type of fabric and soils being washed.

WATER TEMP

WARM WARM

C0LI} WARM

COLD e • HOT

COLDe CO_;LD

Use the warmest water safe for the fabric. Follow garment

label instructions.

Water Temp Use For

Hot Whites and pastels

Heavy soils

Warm Bright colors

Moderate to light soils

Cold Colors that bleed or fade

Light soils

NOTE: In wash water temperatures colder than 60°F (15.6°C),

detergents do not dissolve well. Soils can be difficult to

remove. Some fabrics can retain wear wrinkles and have

increased pilling (the formation of small lint-like balls on the

surface of garments).

Push in the Cycle Control knob and turn it clockwise to the

wash cycle you want. Pull out the Cycle Control knob to start

the washer.

To stop or restart your washer:

• To stop the washer at any time, push in the Cycle Control

knob.

• To restart the washer, close the lid (if open) and pull out

the Cycle Control knob.

This section describes the available wash cycles and will help

you make the best cycle selections for your wash loads. Each

cycle is designed for different types of fabric and soil levels.

• The washer pauses briefly throughout each cycle. These

pauses are normal. Refer to "Normal Sounds" for sounds you

may hear during a wash cycle.

• Refer to "Understanding Washer Cycles" to learn what

happens during a wash cycle.

HEAVY DUTY

RINSE

.....................................................................................10 REGULAR

SPIN

PERMANENT

PRESS

RINSE

SPIN

SOAK

KNIT/DEL(CATE

Heavy Duty

Use this cycle for sturdy or heavily soiled loads. Wash combines

fast-speed agitation and fast-spin speeds.

• Use the Super or Regular settings for heavily soiled and

sturdy fabrics.

• Use the Short setting for light soil and sturdy fabrics.

Permanent Press

The Permanent Press Cycle includes a load-cooling process that

reduces wrinkling. Wash combines fast and slow-speed agitation

and slow spin speeds.

When the timer reaches Pause, the washer will drain and pause

for approximately 2 minutes while some of the wash water is

drained and replaced with rinse water.

Knit/Delicate

Use this cycle for lingerie and loosely knit items. Partway through

the cycle, the washer pauses and soaks the load for gentler care

of lightly soiled delicate items. Wash combines slow-speed

agitation for gentle soil removal and slow spin speeds to reduce

wrinkling.

Soak

The Soak cycle features 4 minutes of agitation followed by an

unlimited soak time to help remove heavy soils and stains that

need pretreatment. You will need to reset the washer to a SPIN

setting to remove water.

• The Soak cycle should be followed by the Heavy Duty or

Permanent Press or Prewash cycle with additional detergent.

NOTE: Hot water is not recommended for soaking. It may set

some stains.

Prewash

Use this cycle to get up to 4 minutes of agitation to help remove

heavy soils and stains that need pretreatment.

• The Prewash cycle should be followed by the Heavy Duty or

Permanent Press cycle with additional detergent.

When using extra detergent for heavily soiled clothes, or washing

special-care items, you may find an extra rinse and spin is

needed.

1. Push inthe Cycle Control knob and turn it clockwise to any of

the RINSE settings.

• For fast agitation and spin, use the Heavy Duty cycle.

• For slow agitation and spin, use the Permanent Press

cycle.

2. Set the WATER LEVEL and WATER TEMP controls to the

desired setting.

3. Pull out the Cycle Control knob. The washer fills to the

selected load size, agitates, drains, and spins.

A drain and spin may help shorten drying times for some heavy

fabrics or special-care items by removing excess water.

1. Push inthe Cycle Control knob and turn it clockwise to any of

the SPIN settings.

• For a fast spin, use the Heavy Duty cycle.

• For a slow spin, use the Permanent Press cycle.

2. Pull out the Cycle Control knob. The washer drains, then

spins.

When the Cycle Control knob is set to a cycle and pulled out, the

washer fills (to the selected load size) before agitation and timing

start. The washer begins agitating immediately after filling;

agitation occurs with the washer lid down.

During agitation, the agitator creates a continuous reliever action

that provides a thorough cleaning of the wash load.

After agitation starts, the Cycle Control knob turns clockwise until

it points to an Off area and the cycle ends.

NOTE: The washer pauses briefly throughout each cycle. These

pauses are normal for washer operation.

WASH RINSE

_ 1. Fill _ 1. Fill

2. Wash selected _ 2. Rinse

time

3. Drain* _j 3. Drain

No agitation No agitation

4. Spin

_j 4. Spin-Spray

Rinse

__ 5. Spin

*The Permanent Press cycle I rm I 6. Off

partially drains, fills, agitates

briefly, and drains.

As with any new product, you will hear sounds that you are not

accustomed to. You may hear various sounds occurring during

the washing, rinsing and spinning process. Between changes in

wash actions, there will be momentary pauses. You will hear

water spraying and splashing during the wash and rinse cycles.

You may hear air being pulled through the pump during the end

of draining or gears changing when the cycle changes. These

sounds are part of normal washer operation.

LAUNDRY TIPS

Preparing clothes for washing

Follow these recommendations to help you prolong the life of

your garments.

• Close zippers, snaps, and hooks to avoid snagging other

items. Remove pins, buckles and other hard objects to avoid

scratching the washer interior. Remove non-washable trim

and ornaments.

• Empty pockets and turn them inside out.

• Turn down cuffs, brush away lint and dirt.

• Turn synthetic knits inside out to avoid pilling.

• Tie strings and sashes so they will not tangle.

• Mend tears, loose hems and seams.

• Treat spots and stains.

• Stained or wet garments should be washed promptly for best

results.

Sorting

• Separate heavily soiled items from lightly soiled ones, even if

they would normally be washed together. Separate lint givers

(towels, chenille) from lint takers (corduroy, synthetics,

permanent press). When possible, turn lint givers inside out.

Separate dark colors from light colors, colorfast items from

noncolorfast items.

Sort by fabric and construction (sturdy cottons, knits, delicate

items).

Loading suggestions (maximum size loads)

Laundry Center

Heavy Work Clothes Towels

2 pair pants 9 bath towels or

3 work shirts 6 bath towels,

3 hand towels &

6 washcloths

Permanent Press Mixed Load

6 shirts or 1 pair pants

2 double sheets & 2 pillowcases

2 pillowcases or 2 shirts

2 single sheets & 1 T-shirt

2 pillowcases

Knits Delicates

2 pair pants & 2 shirts or 1 camisole

3 dresses 2 slips

4 undergarments

1 set of sleepwear

1 half slip

DRYER USE

PUSH TO AUTO DRY II NORMALDRY

STARTDRYER MOREDRY--

LESS DRY

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Do not dry anything that has ever had anything

flammable on it (even after washing).

Failure to follow these instructions can result in death,

explosion, or fire.

Fire Hazard

No washer can completely remove oil,

Do not dry anything that has ever had any type of oil on

it (including cooking oils).

Items containing foam, rubber, or plastic must be dried

on a clothesline or by using an Air Cycle.

Failure to follow these instructions can result in death

or fire.

Before using your dryer, wipe the dryer drum with a damp cloth to

remove dust from storing and shipping.

1. Clean the lint screen before each load. See "Cleaning the Lint

Screen."

2. Load clothes loosely into the dryer and close the door. Do not

pack the dryer. Allow space for clothes to tumble freely.

3. Turn the Cycle Control knob to the recommended cycle and

temperature for the type of load being dried. See "Drying,

Cycle and Temperature Tips."

4. Press PUSH TO START DRYER.

PUSH TO

START DRYER

You can stop your dryer anytime during a cycle.

To stop your dryer

Open the dryer door or turn the Cycle Control knob to OFR

NOTE: The Cycle Control knob should point to an Off area when

the dryer is not in use.

To restart your dryer

1. Close the door.

2. Select a new cycle and temperature (if desired).

3. Press PUSH TO START DRYER.

Load clothes loosely into the dryer. Do not pack the dryer. Allow

space for clothes to tumble freely. The following chart shows

examples of balanced loads that would allow for proper tumbling.

Heavy work 2 pair pants, 3 work shirts

clothes

Delicates 1 camisole, 2 slips, 4 undergarments,

1 set of sleepwear, 1 half slip

Towels 9 bath towels or 6 bath towels, 3 hand

towels, 6 washcloths

Mixed Load 2 pillowcases, 1 T-shirt, 2 shirts,

1 pair pants

Knits 2 pants, 2 shirts; or 3 dresses

Perm. Press 6 shirts; or 2 double sheets & 2 pillowcases;

or 2 single sheets & 2 pillowcases

Select the correct cycle and temperature for your load.

Drying tips

• Follow care label directions when they are available.

• Ifyou use fabric softener sheets, use only ones labeled as

dryer safe. Follow package instructions.

• Remove the load from the dryer as soon as tumbling stops to

reduce wrinkling. This is especially important for permanent

press, knits and synthetic fabrics.

Cycle and temperature tips

• Dry most loads using the Normal Dry (*)setting.

• Use a More Dry setting for drying heavyweight items such as

towels and work clothes.

• Use a Normal Dry setting for drying medium weight items

such as sheets, underwear, permanent press fabrics and

some knits.

• Use a Less Dry setting for drying lightweight items such as

lingerie, blouses, dresses and some knits.

• Use a no heat (air) setting for rubber, plastic or heat-sensitive

fabrics.

• Line dry bonded or laminated fabrics.

If you are unsure of the temperature to select for a load, select a

lower setting rather than a higher setting.

NOTE: If you have questions about drying temperatures for

various loads, refer to the care label directions.

AUTO DRY II NORMALDRY

MORE DRY

-- LESS DRY

OFF OFF

110

AIR DRY 1_° _0o

OFF 0

TOUCH UP -- 2o _o

5o TIMED DRY

Auto Dry II

Use this cycle to dry most loads. Dryness is determined by

thermostats that react to the amount of moisture in the air

exhausted from the dryer. Moist air indicates clothes are damp.

Dry air indicates that moisture has been removed.

This cycle includes a 10 minute (approximate) cool down period

at the end of the cycle to make clothes easier to handle and

reduce wrinkling.

Dry most loads using the Normal Dry (*) setting. When the cycle

ends, check the dryness of the load.

• If the load is drier than you like, select a setting closer to

LESS DRY the next time you dry a similar load.

• If the load is not as dry as you like, complete drying using the

Timed Dry cycle. The next time you dry a similar load, select a

setting closer to MORE DRY.

NOTE: Drying time with an automatic cycle varies according to

the type of fabric, size of load and temperature setting. See

"Drying, Cycle and Temperature Tips."

Timed Dry

Use this cycle to complete drying if items are still damp after the

Auto Dry II cycle. Timed Dry is also useful for heavyweight and

bulky items, such as bedspreads, work clothes, and large loads

that require a long drying time. Use this cycle to get up to

110 minutes of heated drying time. The heating cycle is followed

by a 10 minute (approximately) cool down period.

Touch Up

Use this cycle to smooth synthetic and permanent press clothes

that are clean but wrinkled from being crowded in a closet or

suitcase. This setting provides approximately 20 minutes of

heated tumbling followed by a 10 minute (approximately) cool

down period. Remove clothes immediately when tumbling stops.

Air Dry

Use the Air Dry cycle for items that require drying without heat

such as rubber, plastic and heat-sensitive fabrics. This chart

shows examples of items that can be dried using an air cycle.

Type of Load Minutes*

Foam rubber -- pillows, padded bras, stuffed 20 - 30

toys

Plastic -- Shower curtains, tablecloths 20 - 30

Rubber-backed rugs 40 - 50

Olefin, polypropylene, sheer nylon 10 - 20

*Reset time as needed to allow items to completely dry.

When using Air Dry

• Check to see that coverings are securely stitched.

• Shake and fluff pillows by hand periodically during the cycle.

• Dry item completely. Foam rubber pillows are slow to dry.

End of Cycle Signal

Your dryer sounds a signal when a drying cycle is finished. This

signal is helpful when you are drying items that need to be

removed as soon as the dryer stops in order to help keep

wrinkles from forming.

LAUNDRY CENTER CARE

Keep laundry center area clear and free from items that would

obstruct the flow of combustion and ventilation air.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Failure to do so can result in death, explosion, or fire.

To clean

1. Pull out the lint screen and its cover.

2. Separate the cover and the screen by squeezing the screen

and pulling on the cover at the same time.

Cleaning the exterior

Use a soft, damp cloth or sponge to wipe up any spills such as

detergent or bleach. Occasionally wipe the outside of your

washer to keep it looking new.

Cleaning the interior

Clean your washer interior by mixing 1 cup (250 mL) of chlorine

bleach and 2 scoops or caps full of detergent. Pour this into your

washer and run it through a complete cycle using hot water.

Repeat this process if necessary.

NOTE: Remove any hard water deposits using only cleaners

labeled as washer safe.

Replace inlet hoses after 5 years of use to reduce the risk of hose

failure. Periodically inspect and replace inlet hoses if bulges,

kinks, cuts, wear, or leaks are found.

When replacing your inlet hoses, mark the date of replacement

on the label with a permanent marker.

Obsnin 9{t- eLint Sc ?en

Every load cleaning

The lint screen is located on the back wall of the dryer. Remove

lint before each load. A screen blocked by lint can increase

drying time.

A. Screen

B. Cover

3. Roll lint off the screen with your fingers. Do not rinse or wash

screen to remove lint. Wet lint is hard to remove.

4. Put the lint screen and cover back together and push firmly

back into place.

IMPORTANT:

• Do not run the dryer with the lint screen loose, damaged,

blocked, or missing. Doing so can cause overheating and

damage to both the dryer and fabrics.

• If lint falls off the screen into the dryer during removal, check

the exhaust hood and remove lint. See "Venting

Requirements."

As needed cleaning

Laundry detergent and fabric softener residue can build up on the

lint screen. This buildup can cause longer drying times for your

clothes, or cause the dryer to stop before your load is completely

dry. The screen is probably clogged if lint falls off the screen.

Clean the lint screen (as outlined following) every 6 months, or

more frequently if it becomes clogged due to a residue buildup.

To wash

1. Roll lint off the screen with your fingers.

2. Wet both sides of lint screen with hot water.

3. Wet a nylon brush with hot water and liquid detergent. Scrub

lint screen with the brush to remove residue buildup.

4. Rinse screen with hot water.

5. Thoroughly dry lint screen with a clean towel. Replace screen

in dryer.

To clean dryer drum

1. Apply a liquid, nonflammable household cleaner to the

stained area and rub with a soft cloth until all excess dye

is removed.

2. Wipe drum thoroughly with a damp cloth.

3. Tumble a load of clean cloths or towels to dry drum.

NOTE: Garments which contain unstable dyes, such as denim

blue jeans or brightly colored cotton items, may discolor the

dryer interior. These stains are not harmful to your dryer and will

not stain future loads of clothes. Dry unstable dye items inside

out to avoid dye transfer.

From Inside the Dryer Cabinet

Lint should be removed every 2 years, or more often, depending

on dryer usage. Cleaning should be done by a qualified person.

From the Exhaust Vent

Lint should be removed every 2 years, or more often, depending

on dryer usage.

........... ....... ,_ ...... .._ _ _({}

Install and store your laundry center where it will not freeze.

Because some water may stay in the hoses, freezing can damage

your laundry center. If storing or moving your laundry center

during freezing weather, winterize it.

Non-use or vacation care

Operate your laundry center only when you are at home. If you

will be on vacation or not using your laundry center for an

extended period of time, you should:

• Unplug laundry center or disconnect power.

• Turn off the water supply to the washer. This helps avoid

accidental flooding (due to a water pressure surge) while you

are away.

To winterize laundry center

1. Shut off both water faucets.

2. Disconnect and drain water inlet hoses.

3. Put 1 qt (1 L) of R.V.-type antifreeze in the basket.

4. Run washer on a drain and spin setting for about 30 seconds

to mix the antifreeze and water.

5. Unplug laundry center or disconnect power.

To use laundry center again

1. Flush water pipes and hoses.

2. Reconnect water inlet hoses.

3. Turn on both water faucets.

Electrical Shock Hazard

Plug into a grounded 4 prong outlet.

Failure to do so can result in death or electrical shock.

4. Plug in laundry center or reconnect power.

5. Run the washer through a complete cycle with 1 cup

(250 mL) of detergent to clean out antifreeze.

To transport the laundry center

1. Shut off both water faucets.

2. Disconnect and drain water inlet hoses.

3. If laundry center will be moved during freezing weather, put in

a qt (1 L) of R.V.-type antifreeze in the basket. Run washer on

a spin setting for about 30 seconds to mix the antifreeze and

water.

4. Disconnect the drain from the drain system.

5. Unplug laundry center or disconnect power. Disconnect

wiring if laundry center is direct wired.

6. Disconnect the exhaust vent.

7. Wash lint screen.

8. Make sure leveling legs are secure.

9. Place the inlet hoses into the basket.

10. Drape the power cord and drain hose over edge and into the

basket.

11. Use masking tape to secure the washer lid and dryer door.

Reinstalling your laundry center

1. Follow the "Installation Instructions" to locate, level and

connect the laundry center.

2. Run the washer through a complete cycle with 1 scoop or

capful of detergent to clean the washer and remove the

antifreeze, if used.

La page charge ...

Kenmore 1101820296 Le manuel du propriétaire

Marque: Kenmore

Modèle: 1101820296

Catégorie: Machines à laver

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Kenmore 1101820296 Owner's manual

Kenmore 1101820296 Le manuel du propriétaire

Kenmore 1101820296 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents