Bose Speaker System 149393 Manuel utilisateur

Marque: Bose

Modèle: Speaker System 149393

Taper: Manuel utilisateur

This PDF includes both the English and

the French versions of this document.

Ce PDF inclut les versions anglaises

et françaises de ce document.

The Bose

901

Series VI Direct/Reecting

Speaker System

Owner’s Guide

Brugervejledning

Bedienungsanleitung

Guía del usuario

Notice d’utilisation

Manuale d’istruzioni

Gebruiksaanwijzing

Bruksanvisning

Bose

901

Series VI Direct/Reecting

Speaker System

English

WARNING: To reduce the risk of ﬁre or electric shock, do not expose the system to rain or

moisture.

WARNING: The apparatus shall not be exposed to dripping or splashing, and objects ﬁlled with

liquids, such as vases, shall not be placed on the apparatus. As with any electronic products, use

care not to spill liquids into any part of the system. Liquids can cause a failure and/or a ﬁre hazard.

CAUTION

These CAUTION marks are located on the bottom of your 901

active equalizer:

The lightning ﬂash with arrowhead symbol, within an equilateral triangle, is intended to alert the

user to the presence of uninsulated dangerous voltage within the system enclosure that may be

of sufﬁcient magnitude to constitute a risk of electric shock.

The exclamation point within an equilateral triangle, as marked on the system, is intended to alert the

user to the presence of important operating and maintenance instructions in this owner’s guide.

CAUTION: To prevent electric shock, match wide blade of plug to wide slot, insert fully.

Note: Where the mains plug or appliance coupler is used as the disconnect device, such discon-

nect device shall remain readily operable.

Additional safety information

See the additional instructions on the Important Safety Information page enclosed with this

owner’s guide.

Please read this owner’s guide

Please take the time to follow this owner’s guide carefully. It will help you set up and oper-

ate your system properly, and enjoy all of its advanced features. Save your owner’s guide for

future reference.

Safety Information

registered trademarks of Bose Corporation.

For your records

Serial numbers are located on the bottom panel of each 901 speaker and on the back of the

active equalizer.

Loudspeaker Serial Numbers: _______________________________________________________

Active equalizer Serial Number: _____________________________________________________

Dealer name: _____________________________________________________________________

Dealer phone: _______________________ Purchase date: _____________________________

We suggest you keep your sales slip and warranty card together with this owner’s guide.

English

Contents

Where to nd…

Contents

Where to ﬁnd… ............................................................................................................. 3

Warranty period ............................................................................................................. 3

Customer service .......................................................................................................... 3

Setting Up

Before you begin ........................................................................................................... 4

Unpacking the cartons .................................................................................................. 4

System compatibility ..................................................................................................... 5

Choose the support for your speakers .......................................................................... 6

Choosing the location for your speakers ...................................................................... 6

Speaker connections..................................................................................................... 8

Equalizer connections ................................................................................................... 9

Testing the speakers and equalizer ............................................................................. 12

Using other equipment ................................................................................................ 13

Using your 901

Series VI speaker system

Playing your speakers ................................................................................................. 14

Adjusting the sound .................................................................................................... 15

Equalizer compatibility ................................................................................................ 16

Connecting additional speakers .................................................................................. 16

Maintaining Your 901 speaker system

Cleaning your speakers ............................................................................................... 17

Troubleshooting ........................................................................................................... 17

Product Information

Technical information .................................................................................................. 18

Accessories ................................................................................................................. 18

Bose Corporation ......................................................................................inside back cover

Warranty period

The Bose

901 speakers and active equalizer are covered by a limited 5-year transferable

warranty. Details of the warranty are provided on the warranty card that came with your

system. Please ﬁll out the information section on the card and mail it to Bose Corporation.

Customer service

For additional help in solving problems, contact Bose customer service. See the inside back

cover for Bose customer service ofﬁces and phone numbers.

A free booklet is available: Guide to Optional System Connections for Bose 901

Direct/

Reﬂecting

Speaker Systems. Ask for part number 149393.

English

Setting Up

Before you begin

Thank you for purchasing the Bose

901

Series VI Direct/Reﬂecting

speakers. They represent

the best in Bose Corporation speaker design and engineering and will give you many years of

listening pleasure.

The installation and operating principles of this system are signiﬁcantly different from those of

conventional speakers. To obtain the best possible performance and avoid problems, please

take the time to read this guide.

CAUTION: You must have a Bose 901 active equalizer for a complete 901 speaker system. The

use of 901 Series VI speakers without the 901 Series VI active equalizer will result in improper per-

formance. The use of graphic or parametric equalizers, instead of the Bose 901 equalizer, will result

in unsatisfactory performance.

Conventional graphic and parametric equalizers may be used in addition to, but not in place

of the Bose 901 active equalizer. However, the use of such additional equalizers is not recom-

mended since it will not improve system performance. For adequate performance you must

use the 901 Series VI active equalizer with these speakers.

Unpacking the cartons

A complete Bose 901 Series VI speaker system consists of three matched components: two

901 Direct/Reﬂecting

speakers and a separate 901 Series VI active equalizer. Two cables are

included to connect the active equalizer to your receiver or ampliﬁer. The 901 speakers and

equalizer are packed in three separate cartons. Carefully unpack your system, saving all pack-

ing materials for possible future use.

Inspect the speakers and equalizer. If any part appears damaged, do not attempt to use the

system. Repack the speakers and equalizer in their original cartons and notify your authorized

Bose dealer immediately.

Note: Now is a good time to record the serial numbers of each speaker and the active equalizer.

Please write them on your warranty card and in the spaces provided on page 2. The serial num-

bers are located on the bottom of the 901 speakers and on the back of the equalizer.

WARNING: Each speaker carton weighs over 35 lb (16 kg). Use good lifting practice to avoid

injury.

WARNING: To avoid danger of suffocation, keep the plastic bags out of the reach of children.

Figure 1

What comes in the three cartons:

• Two 901 speakers

• One 901 active equalizer

• Two equalizer cables

English

Setting Up

System Compatibility

Bose

901

Series VI speakers and Series VI active equalizer work with your stereo

components to produce a superb music system. The active equalizer is an integral part

of the system and may be connected in a variety of ways, depending on the components

you have. The two most common methods are described in this guide. Using different

components may require different connection methods. More information is available by

calling Bose Corporation. Ask for the free booklet, Guide to Optional System Connections

for Bose 901 Direct/Reﬂecting

Speaker Systems, part number 149393.

Your 901 speakers are designed to work compatibly with receivers or ampliﬁers rated from

10 to 450 watts per channel. In this guide, the term receiver is used to refer to an integrated

preampliﬁer and power ampliﬁer (which may also contain an AM/FM tuner). The term

ampliﬁer is used to describe conﬁgurations involving separate preampliﬁer and ampliﬁer

components.

Most receivers have a TAPE MONITOR connection. The 901 active equalizer is most

commonly connected to the tape monitor connections on the receiver. If you plan to

connect a tape recorder, use the set of inputs and outputs located on the back of the 901

active equalizer marked TAPE RECORDER CONNECTIONS.

If you have recently purchased a home theater receiver, you may be considering using

your 901 speakers for the front channels. Your home theater receiver must have accessible

PRE AMP OUT/MAIN AMP IN connections for the front channels if you are to use your 901

speakers in this way. These may also be called the ADAPTER or SIGNAL PROCESSOR

connections.

Installation steps

Follow these steps, in the order below, to install your 901 Series VI speaker system.

1. Choose the best locations and support for the 901 speakers (page 6).

2. Connect the speakers to the ampliﬁer or receiver (page 8).

3. Connect the 901 active equalizer to the ampliﬁer or receiver using either the TAPE

MONITOR or PRE AMP OUT/MAIN AMP IN connections (page 9).

4. Test the system to see that the audio signal is correctly processed by the active equal-

izer (page 12).

English

Setting Up

Choosing the location for your speakers

Choose locations for your 901

speakers that use the walls to best advantage by reﬂecting

sound throughout the listening room. Refer to the drawing on page 7.

Guidelines for placement

Place the speakers along the same wall (see Figure 3):

• 4 to 12 feet (1.2 – 3.6 m) apart, with the V-shaped rear of the speaker between 8 and 18

inches (20 – 45 cm) from the rear wall. Do not aim the V toward a corner.

• 18 inches (45 cm) of clear space around the sides, top, and bottom of the speakers.

• at least 2 feet (60 cm) from sound-absorbent furnishings.

• 18 to 48 inches (45 – 120 cm) from the side and rear walls.

• 18 to 36 inches (45 – 91 cm) from the ﬂoor or ceiling. Do not place the speakers exactly

halfway between ﬂoor and ceiling.

Within these guidelines, remember that the closer the speakers are placed to a reﬂective

surface, like a wall, the more bass is reproduced.

Choose the support for your speakers

You may place 901 speakers on a table or shelf. You may also use Bose

ﬂoor pedestals, or

suspend the speakers from your ceiling. Refer to Figure 3 on page 7.

To set the speakers on a table or shelf

Although each speaker weighs 35 lb (16 kg), a suitable shelf or table must be able to support

140 lb (64 kg). Keep an adequate distance between the speakers and the rear wall as listed in

“Guidelines for placement” above.

To stand the speakers on the oor

Use only Bose pedestals (PS-6) as ﬂoor stands. They are designed to provide the proper

support and are available through your authorized Bose dealer. Please read the pedestal

attachment instructions before making any speaker connections. Four pilot holes on the

bottom of each speaker (see Figure 2, hole set A) are pre-drilled for the purpose of anchoring

the speaker to the pedestal.

To suspend the speakers from the ceiling

Use these guidelines to ensure safe suspension of your 901 speakers. Three steel support

chains are recommended. We cannot specify the ceiling attachments. The type to use

depends on the type of building construction.

CAUTION: Do not mount on surfaces that are not sturdy enough, or that have hazards con-

cealed behind them, such as plumbing or electrical wire. If you are unsure of your ability to install

these speakers, contact a qualiﬁed professional installer.

Note: The speakers hang in an inverted position, with the terminal connections facing up.

Carefully rotate the Bose logo 180˚ (so it appears right side up) before hanging the speakers.

Figure 2

Pedestal (A) and ceiling mount

(B) pilot holes

English

Setting Up

Hardware needed for ceiling suspension

• Screw hooks support the chains at the ceiling. They must have at least a #10 wood thread

with a shank diameter of at least

⁄

inch (4.5 mm). They should be long enough to go

through any plasterboard and still have at least one inch (25 mm) of thread left to pene-

trate a wood beam. For a masonry ceiling: use only high-quality metal expansion masonry

anchors that ﬁt the thread of the ceiling hooks.

• Chain: diameter should be at least

⁄

inch (0.135 in. or 4 mm).

• Screw eyes with S hooks attach chains to the speaker and must have at least a #10 wood

thread with a shank diameter of at least

⁄

inch (4.5 mm) or larger.

• All hardware (screw hooks, chain, screw eyes, S hooks) must have a manufacturer’s safe-

load rating of 40 lb (18 kg) or more.

General notes on ceiling suspension

• Suspend the speakers 18 – 36 inches (45 – 91 cm) from the ceiling; do not mount them

ﬂush to the ceiling.

• To ensure an accurate stereo image, the distance from the ﬂoor should be three to ten feet

(1 – 3.5 m). Be sure the speakers are no less than 18 inches (45 cm) from the ﬂoor. Do not

suspend the speakers exactly halfway between the ﬂoor and ceiling.

Note: If the speakers are more than 10 feet (3 m) from the ﬂoor, we suggest you lengthen the

chain supporting the rear of the speaker. By doing this you will allow the rear of the speaker,

housing eight of the nine drivers, to be angled slightly downward.

Step by step procedure for ceiling suspension

1. Ceiling: Anchor at least two screw hooks into a rigid structural ceiling support (beam, joist,

or masonry anchor). Drill pilot holes into wood using a

⁄

inch drill bit (3.7 mm), if neces-

sary.

2. Speaker: Use the three pre-drilled pilot holes (see Figure 2 - hole set B) on the bottom of

each speaker. Use a

⁄

inch drill bit (3.7 mm) to enlarge the pilot holes to accept the #10

thread screw eyes. Drill to a depth of

⁄

inch (12 mm) in the speaker cabinet. Do not drill

completely through the cabinet.

Note: Contact Bose

for more information on suspending speakers. See the inside back cover

for phone numbers. For details on your speciﬁc ceiling construction, consult a qualiﬁed building

contractor or professional installer.

Figure 3

Mounting guidelines

18 – 48”

(45 – 120 cm)

18 – 36” (45 – 91 cm)

4 – 12’

(1.2 – 3.6 m)

18 – 48”

(45 – 120 cm)

4 – 12’

(1.2 – 3.6 m)

18 – 36” (45 – 91 cm)

8 – 18” – (20 – 45 cm)

English

Setting Up

Speaker connections

With your speakers in their chosen locations, connect them to the receiver.

Choosing the wire

It is important to use the right thickness of speaker wire. For distances of up to 30 feet (9 m),

18 gauge (.075 mm

) 2-conductor wire works well. For distances greater than 30 feet (9 m),

refer to the wire recommendations chart on page 18.

Note: To determine if this wire is suitable for use in a wall or under a ﬂoor, check your local build-

ing codes. You may want to contact a qualiﬁed electrical installer for this information.

Preparing the speaker wires

Examine the speaker wire. Note that it is actually a pair of insulated wires that may be gently

pulled apart. The insulation around one wire is marked with a stripe, collar, rib, groove, or

printing. Use the marked wire as positive (+) and the unmarked wire as negative (-). These

wires correspond to the positive and negative terminals on the speaker and receiver.

Note: It may be difﬁcult to distinguish wire markings. Inspect both wires carefully.

To prepare the ends of each wire:

1. Strip approximately

inch (12 mm) of insulation from both wires.

2. Twist the bare ends of each stranded wire, to prevent strands from touching across

terminals.

Connecting the speakers

CAUTION: Before making any connections, turn off your receiver and unplug it from the AC

(mains) power outlet. Not doing this may result in damage to your system.

Speaker terminals are located on the bottom of each speaker. Unscrew the knurled nut on

each terminal and remove one washer. Wrap one bare wire end around the terminal post.

Then, replace the metal washer on the screw post and screw the knurled nut ﬁrmly back on.

1. Connect one wire pair to the right speaker (the one on your right as you face it).

a. Attach the marked wire at one end to the positive (+) terminal.

b. Attach the plain wire at that end to the negative (-) terminal.

2. Connect the other ends of the same wire pair to the RIGHT SPEAKER OUTPUT of your

receiver.

a. Attach the marked wire to the positive (+) terminal.

b. Attach the plain wire to the negative (-) terminal.

3. Following the steps above, connect the second pair of wires to the left speaker and to the

LEFT SPEAKER OUTPUT on the receiver.

Note: If your receiver offers a choice of output impedances, use the terminal marked 8 or 8

ohms.

English

Setting Up

Checking the speaker connections

Make sure the terminal knurled nut is tightened down ﬁrmly. Any gap between the wire and

terminal can cause heat build up. Check to be sure the wires are connected positive to posi-

tive (+ to +) and negative to negative (- to -). Make sure no loose strands of wire touch across

terminals, which can cause short circuits.

Figure 4

Connecting the speakers to the

receiver

Equalizer Connections

There are two options for connecting the equalizer. Your choice depends on the type of

receiver you own and whether you plan to use the system primarily for stereo or for home

theater enjoyment.

Stereo/non-home theater use

(tape monitor connections)

The Bose

901

active equalizer connects directly to your receiver through the tape monitor

connection. If your receiver has more than one tape connection, use the second one (TAPE 2).

To connect a tape deck, use the additional set of inputs and outputs located on the back of the

901 active equalizer marked TAPE RECORDER CONNECTIONS.

The TAPE MONITOR switch on the front of the receiver lets you switch the equalizer in and out

of the signal path. This is important when you want to play conventional, non-equalized speak-

ers or headphones attached to your receiver. See Using other equipment on page 13.

Note: If your receiver is designed for home theater use, it may not have a Tape Monitor switch.

If not, you must use a PRE AMP OUT/MAIN AMP IN connection. This may also be called the

ADAPTER or SIGNAL PROCESSOR connection. Refer to “Home theater use (PRE AMP OUT/

MAIN AMP IN)” on page 10 for instructions on how to connect for home theater use.

1. Disconnect any external tape deck or signal processor connected to the tape monitor

connection.

2. Use the twin cable assemblies (with two connectors at each end) that are supplied with

the equalizer. Use the red connector for the right (R) channel connections and the other

connector for the left (L) channel connections.

Receiver

L R

+ – + –

English

Setting Up

3. Connect one end of a cable to the AMPLIFIER INPUT jacks on the 901

active equalizer.

a. Insert the ﬁrst connector ﬁrmly into the INPUT jack marked R.

b. Insert the second connector into the INPUT jack marked L.

4. Connect the other end of the cable to the OUT or RECORD jacks on your receiver. These

jacks may be marked TO INPUT, FROM INPUT, or REC.

a. Insert the ﬁrst connector into the OUT or RECORD jack marked R.

b. Insert the second connector into the OUT or RECORD jack marked L.

5. Connect the second cable from the AMPLIFIER OUTPUT jacks on the 901 active equalizer

to the IN or TAPE jacks on your receiver. These jacks may be marked PLAY, TO OUTPUT,

FROM OUTPUT, or MONITOR.

6. Plug the power cord of the 901 active equalizer into one of the switched outlets on the

receiver so that it will be powered when the receiver is switched on.

Figure 5

Connecting to the tape monitor

connection

Home theater use

(PRE AMP OUT/MAIN AMP IN)

Use these instructions:

• for stereo-only operation if your receiver does not have a TAPE MONITOR connection.

• if you are using a surround sound receiver that has a section on the back marked PRE AMP

OUT/MAIN AMP IN. The jacks may be labeled ADAPTER or SIGNAL PROCESSOR.

Note: If your receiver does not have this PRE AMP OUT/MAIN AMP IN section, the 901

speakers will not be usable in your home theater system.

1. The PRE AMP OUT/MAIN AMP IN jacks on your receiver are usually connected by small

bars called horseshoe pins. Remove these pins. See Figure 6.

Figure 6

Removing horseshoe pins

OUTPUT INPUT

AMPLIFIER

CONNECTIONS

R L R L

( TO AMP “TAPE IN” )

( FROM AMP “TAPE OUT

” )

OUTPUT INPUT

TAPE RECORDER

CONNECTIONS

R L R L

( TO REC “INPUT” )

( FROM REC “OUTPUT

” )

901.E.

SERIAL

254818

ˆII¨

120V AC

60Hz 2.5W

ENGINEERED IN U.S.A. BY BOSE CORPORATION

FRAMINGHAM, MA 01701-9168 ASSEMBLED IN MEXICO

LISTED 917D

AUDIO

EQUIPMENT

Amplifier or Receiver

901

Active Equalizer

MAIN

AMP

PRE

AMP

OUT

English

Setting Up

2. Use the twin cable assemblies (with two connectors at each end) that are supplied with the

equalizer. Use one connector for the right (R) channel connections and the other connector

for the left (L) channel connections.

3. Connect the ampliﬁer INPUT of the Bose

901

active equalizer to the PRE AMP OUT jacks

of the receiver or ampliﬁer. Connect right channel to right channel and left to left.

4. Connect the ampliﬁer OUTPUT of the active equalizer to the MAIN AMP IN jacks on the

receiver or ampliﬁer. Connect right channel to right channel and left to left.

5. Plug the power cord of the 901 active equalizer into one of the switched outlets on the

receiver so that it will be powered when the receiver is switched on.

Note: This connection method does not allow you to connect a tape deck directly to the active

equalizer. Connect it to the receiver instead.

Check to see that the 901 speakers are connected to the receiver MAIN or FRONT speaker

jacks. In this way the 901 active equalizer signals will reach only the 901 speakers – the front

channels of your home theater – and not any non-901 speakers used as center and surround

channels.

Call Bose Corporation for assistance with the connection of additional speakers or signal

processing equipment. Refer to the address information inside the back cover of this guide.

A free booklet is available (USA only): Guide to Optional System Connections for Bose 901

Direct/Reﬂecting

Speaker Systems. Ask for part number 149393.

Figure 7

Home theater receiver

connections

English

Setting Up

Testing the speakers and equalizer

Choose the test method appropriate to your system:

To test the TAPE MONITOR connection

1. Turn off or disconnect any non-901 speakers or headphones that may be connected.

2. On the 901

active equalizer, press the MONITOR button IN to TAPE, and the BASS

button OUT to position 1.

3. Set the MID-BASS and MID-TREBLE sliders to center positions.

4. Press your receiver or ampliﬁer TAPE or TAPE MONITOR button to the OUT or NORMAL

position so it is not selected.

5. Play music through your system. You should hear both speakers. Do not worry about the

sound quality at this point. The equalizer is not yet engaged. If there is no sound from one

or both speakers, check the receiver and speaker connections.

6. Move the receiver BALANCE control to the extreme left and then to the extreme right.

This tests the left and right channel orientation. If the channels are reversed, check the

connections.

To test the equalizer

You have now tested your speakers and their wiring. The following steps test the equalizer

and its wiring:

1. With the speakers playing, press the receiver TAPE or TAPE MONITOR button IN, select-

ing the PLAY or MONITOR position. All sound should stop. If it does not, check your

equalizer wiring. Be sure the 901 active equalizer MONITOR button is set to position 2

(TAPE).

2. Press the 901 active equalizer MONITOR button to SOURCE, position 1. The sound

should return with full, natural sound characteristics. The system is now ready for use.

If the sound does not return, and the equalizer power indicator is lit, the equalizer is

probably connected incorrectly. Review equalizer connections.

To test the PRE AMP OUT/MAIN AMP IN connection

If you have connected the 901 active equalizer to the PRE AMP OUT/MAIN AMP IN connec-

tion, follow these instructions to test the speakers, equalizer, and wiring before connecting

any other equipment to your system.

1. Turn off or disconnect any non-901 speakers or headphones that may be connected.

If your system has a speaker selector switch, set it so that only the 901 speakers are

connected to your power ampliﬁer.

2. On the 901 active equalizer, press the MONITOR button OUT to SOURCE, and the BASS

button OUT to position 1.

3. Set the MID-BASS and MID-TREBLE sliders to center positions.

4. Play music through your system. You should hear both speakers. If there is no sound from

one or both speakers, check to see that the power indicator on the equalizer is lit, then

check the receiver and speaker connections.

English

Setting Up

5. Move the receiver BALANCE control to the extreme left and then to the extreme right.

This tests the left and right channel orientation. If the channels are reversed, check the

connections.

6. Turn off the receiver and temporarily unplug the 901

active equalizer from its AC (mains)

power outlet.

7. Turn your receiver back on. You should not hear any music through the system. If you do,

the equalizer is probably connected incorrectly. Check the equalizer connections.

8. Turn off the receiver before restoring AC power to the 901 equalizer. Plug the equalizer

back in to its AC outlet. The system is now ready for use.

Using other equipment

You can use the Bose

901 active equalizer TAPE CONNECTION jacks for a tape deck, VCR

audio connection, signal processors, or other components. This will be necessary if your

receiver has only one tape connection and you have connected the equalizer to it. If you

connected the equalizer to the receiver’s TAPE 2 connection, you can use TAPE 1 for these

components.

Before making any connections, turn off the receiver and components. Be sure the active

equalizer power indicator is off.

To add a tape deck or VCR:

1. Use cables with RCA connectors at each end. One color (usually red) is for right (R) chan-

nel connections and the other connector is for left (L) channel connections.

2. Connect the TAPE RECORDER OUTPUT of the equalizer to the LINE IN/REC of the tape

deck. Connect right channel to right channel and left channel to left channel.

3. Connect the TAPE RECORDER INPUT of the equalizer to the LINE OUT/PLAY of the tape

deck. Connect right channel to right channel and left channel to left channel.

Note: To use an external signal processor, or to add a graphic equalizer, contact Bose for more

information. Refer to the inside back cover of this guide.

A free booklet is available (USA only): Guide to Optional System Connections for Bose

901

Direct/Reﬂecting

Speaker Systems. Ask for part number 149393.

Figure 8

Connecting a tape deck to the

901 active equalizer

English

Playing your speakers

Always use the 901

active equalizer when playing your 901 speakers. How you set the equal-

izer depends on how it is connected to your receiver.

When connected to TAPE MONITOR

Press your receiver TAPE MONITOR button to the IN or MONITOR position. This switches the

equalizer into the system. Check periodically to be sure the TAPE MONITOR is engaged. On

some receivers the button may be labeled RECORD SELECT or RECORD OUT.

To play a tape deck connected to the equalizer, press the MONITOR button on the equalizer

IN (TAPE, position 2).

Return the MONITOR button to OUT (SOURCE, position 1) to listen to components other than

the tape deck (CD player, radio, etc.).

CAUTION: Do not use the active equalizer with conventional, non-equalized speakers or head-

phones. This can produce unnatural sound, and can even damage some non-901 speakers.

Before you play any non-901 speakers, be sure the receiver TAPE MONITOR button is OFF (OUT

or NORMAL).

You can play a tape deck through conventional, non-equalized speakers, even if your receiver

has only one tape monitor connection. Follow these steps to do this:

1. Connect the tape deck outputs to the AUX input jack on your receiver.

2. Leave the inputs of the tape deck connected to the TAPE OUTPUT jacks on the 901 active

equalizer.

3. Press the receiver TAPE MONITOR to OFF (OUT or NORMAL). This allows you to record

disc and radio sources. You may also play any program source (including tape) with or

without 901 equalization.

Note: This arrangement works only with tape decks. Do not use it with any type of signal pro-

cessing device.

When connected to PRE AMP OUT/MAIN AMP IN

1. You must leave the MONITOR button on the 901 active equalizer OUT (SOURCE,

position 1) at all times.

2. Do not connect tape decks to the 901 active equalizer when it is connected to this ampli-

ﬁer connection. Connect the tape deck to the receiver or ampliﬁer TAPE MONITOR con-

nection or AUX inputs.

3. The power ampliﬁer is always receiving the 901 active equalized signal. This signal can

damage conventional speakers and headphones. Therefore, do not connect conventional

speakers or headphones unless you have disconnected the 901 equalizer.

Do not connect tape decks or signal processing devices to the 901 active equalizer when it is

connected between the preampliﬁer and main ampliﬁer.

Using Your 901

Series VI Speaker System

English

Using Your 901

Series VI Speaker System

Adjusting the sound

Adjust the sound using the MID-TREBLE and MID-BASS sliders and BASS control on the

901

active equalizer. Use the tone controls on your receiver only after the MID-TREBLE and

MID-BASS sliders have been set according to the procedures below.

Using the MID-TREBLE and MID-BASS sliders

These controls let you make adjustments to compensate for the effects of speaker location,

room acoustics, and program quality.

1. Select a familiar musical piece.

2. Set your receiver tone controls to the center (ﬂat) position. If it has a loudness compensa-

tion control (marked LOUD or LOUDNESS), set it to the OFF or OUT position.

3. Set the MID-TREBLE slider on the equalizer to its center position.

4. Play the selected music through the 901 speakers at normal volume. Move the MID-BASS

slider back and forth several times and listen to the effect. You should hear a signiﬁcant

change in the fullness of the sound. If you do not, the active equalizer may not be engaged.

Refer to Playing your speakers on page 14.

5. When you are familiar with the effect of the MID-BASS slider, set it to the extreme left. Start

the musical passage again and slowly advance the MID-BASS slider to the right until the

sound is rich and full, without excessive heaviness.

6. Replay the musical passage, this time moving the MID-TREBLE slider back and forth to

become familiar with its effect. You should hear a signiﬁcant change in clarity of the sound.

7. Set the MID-TREBLE slider to the extreme left and play the passage again. Slowly advance

the MID-TREBLE slider to the right until the sound is clear and detailed without excessive

shrillness.

Using the BASS control

The Bass control provides an alternate bass equalization. It is not a bass enhancement switch,

and it is not intended to boost the bass output of the speakers.

Press the BASS control IN (to position 2) to engage an alternate form of equalization that

changes the way the speakers handle low-frequency information. For example, you may

prefer pipe organ music with the alternate equalization. The control can also be useful in

eliminating feedback or rumble from a turntable.

English

Using Your 901

Series VI Speaker System

Equalizer compatibility

The Bose

901

Series VI active equalizer is designed for speciﬁc use with

Bose 901 Series VI speakers. It may also be used with 901 Series V speakers.

WARNING: Bose 901 Series I, II, III, or IV speakers require a substantially

different equalization. The 901 Series VI active equalizer must not be used with

Series I – IV speakers. For additional information on the active equalizer, please

contact Bose Service.

Connecting additional speakers

The type of speakers and how you will use them determines how many ampli-

ﬁers and 901 active equalizers you will need.

To run other non-901 speakers simultaneously requires the addition of a

second ampliﬁer. To use other speakers simultaneously with the 901 speakers

requires the ability to isolate the 901 active equalizer signal so that it affects

only the 901 speakers.

Adding 901 speakers

You need just one 901 Series VI active equalizer to use a second pair of 901

Series VI speakers connected to a single receiver or ampliﬁer. Connect the

additional speakers to the additional speaker output jacks on the receiver or

ampliﬁer.

To use extra 901 speakers in a four channel or time-delay music system, you

will need a separate 901 active equalizer for each pair of speakers.

Adding conventional speakers

You need a separate power ampliﬁer to play conventional speakers at the

same time as 901 speakers. Connect the 901 active equalizer to the ampliﬁer

that drives the 901 speakers only.

CAUTION: Make sure the conventional speakers do not receive signals from the

901 active equalizer.

Call Bose Corporation for assistance with the connection of additional speak-

ers or signal processing equipment. Refer to the address information on the

inside back cover of this guide.

A free booklet is available (USA only): Guide to Optional System Connections

for Bose 901 Direct/Reﬂecting

Speaker Systems. Ask for part number 149393.

English

Problem What to do

One speaker sounds • Do not switch the wires; this could damage a speaker. Turn off the ampliﬁer and disconnect

defective, or does not play the defective speaker wire at the ampliﬁer. Reconnect it to the other channel. If the speaker

now plays correctly, the problem is not in the speaker or wiring.

Neither speaker plays • Connect the speakers to another receiver or ampliﬁer that is known to be operating

properly. If the speakers now play correctly, the problem is not in the speakers.

Note that the tonal balance of the 901 speakers will be incorrect if the 901 active equalizer

is not being used with this second receiver or ampliﬁer.

The high and low • Check to be certain that the 901 active equalizer is in the circuit. Review the Playing

frequencies seem weak your speakers section of this guide on page 14.

You hear distortion • Try turning down the volume. If the distortion goes away you may be using an insufﬁciently

at high volume levels powered receiver or ampliﬁer.

The trouble seems to be in • Bypass the equalizer to see if the system operates properly without it. (Speakers will not

the 901 active equalizer have any highs or lows.) Check to see that all connections are correct and that none of

the cables is defective.

Trouble persists in the • Contact your authorized Bose

dealer to verify any defects and arrange for service by

speakers or equalizer a factory authorized agency or by the Bose factory. Bose Corporation will make every

effort to remedy any problem within the terms of the warranty.

Maintaining Your 901

Series VI Speaker System

Cleaning your speakers

If your 901

speakers have a painted surface, clean with a soft damp cloth. If necessary, use

a mild detergent such as dish soap. If the speakers have a wood veneer ﬁnish, clean them

with wood furniture polish. You may vacuum the speaker grille panels carefully, if necessary.

Do not use any sprays near the system. Do not use any solvents, chemicals, or cleaning

solutions containing alcohol, ammonia, or abrasives. Do not allow liquids to spill into any

openings.

Troubleshooting

If you have a problem with your 901 Series VI speakers or 901 active equalizer, turn off the re-

ceiver or ampliﬁer before you proceed. Then check all the connections between the speakers,

receiver, and active equalizer. Correct any wiring problems before you follow the guidelines

below. Problems are more likely to originate with equipment other than speakers, so you may

also want to refer to your receiver or other component owner’s guides.

English

Product Information

901 Series VI active equalizer

Input Impedance

47 k ohms (47 kΩ)

Output Impedance

1 k ohm

Usable dynamic range

106 dB @ 35 Hz

Noise (A-weighted)

Greater than 90 dB below 1 volt

Distortion

Less than 0.09% THD at 1 kHz, 1 V input

Compensation controls

Mid-Bass, ±6 dB @ 225 Hz

Mid-Treble, ±6 dB @ 3 kHz

Bass Switch

– 6 dB @ 35 Hz

Power Requirements

120V ~ 50/60Hz, 3.5W

220-240V ~ 50/60Hz 3.5W

100V ~ 50/60Hz 3.5W

Cabinet

Black anodized aluminum

Dimensions

13”W x 2

”H x 5”D

(33.0 x 7.0 x 12.7 cm)

Weight

3.4 lb (1.5 kg)

Technical information

Bose

901

Series VI Direct/Reﬂecting

Loudspeakers

Transducer complement

Nine (9) 4

” (11.4 cm) full-range Helical

Voice Coil drivers in each cabinet

Energy dispersion

89% by reﬂection

11% by direct radiation

Enclosure

14-element Acoustic Matrix

™

enclosure

with three reactive air columns

Nominal impedance

8Ω (ohms)

Amplier compatibility

Compatible with ampliﬁers/receivers rated

from 10 - 450 watts RMS.

Rated 250 watts IEC

Recommended fusing

Series connected 3A quick-acting fuse

Buss AGC-3, Littelfuse 312-003, or equiva-

lent

Cabinet

Oil-rubbed hardwood veneer with

walnut ﬁnish

Black vinyl veneer

Dimensions

21”W x 12

”H x 13”D

(53.3 x 32.0 x 33.0 cm)

Weight

35 lb. (16 kg) per enclosure

Wire recommendations

Gauge Length

18 (0.75 mm

) 30 ft (9 m) maximum

16 (1.5 mm

) 45 ft (14 m) maximum

14 (2.0 mm

) 70 ft (21 m) maximum

Accessories

To ﬁnd out about PS-6 ﬂoor pedestals, contact your Bose dealer. Or call Bose directly (see inside

back cover for phone numbers).

Bose

Corporation

Italia

Bose S.p.A., Via della Magliana 876

00148 Roma

www.bose.iT

TEL 06-65670802 FAX 06-65680167

Japan

Bose K.K., Shibuya YT Building

28-3 Maruyama-cho

Shibuya-ku, Tokyo 150

TEL 3-5489-0955 FAX 3-5489-0592

Nederland

Bose B.V., Nijverheidstraat 8

1135 GE Edam

TEL 0299-390111 FAX 0299-390109

Norge

Bose A/S, Solheimsgate 11

N-2001, Lillestrøm

TEL 63-817380 FAX 63-810819

Österreich

Bose Ges.m.b.H., Vienna Business Park Wienerberg-

strasse 7 (10.OG)

A-1100 Vienna

TEL 01-60404340 FAX 01-604043423

Schweiz

Bose AG, Rünenbergerstrasse 13

4460-Gelterkinden

TEL 061-9815544 FAX 061-9815502

Sverige

Bose A/S, Johannefredsgatan 4

S-43153 Mölndal

TEL 31-878850 FAX 31-274891

United Kingdom

Bose Limited

1 Ambley Green

Gillingham Business Park

Gillingham, Kent ME8 ONJ

TEL 0870-741-4500 FAX 0870-741-4545

From other locations

Bose Customer Service, 1 New York Ave.

Framingham, MA 01701-9168 USA

TEL (508) 766-1900 FAX (508) 766-1919

World Wide Web

www.Bose.com

USA

Bose Corporation, The Mountain

Framingham, MA 01701-9168

1-800-367-4008

Phone hours - ET (eastern time):

Weekdays 8:30 a.m. to 8 p.m.

Saturdays 9 a.m. to 3 p.m.

Canada

Bose Ltd., 1-35 East Beaver Creek Road

Richmond Hill, Ontario L4B 1B3

1-800-465-2673

Phone hours - ET (eastern time):

Weekdays 9 a.m. to 5 p.m.

European Ofce

Bose Products B.V., Nijverheidstraat 8

1135 GE Edam, Nederland

TEL 0299-390111 FAX 0299-390114

Australia

Bose Pty Limited, 1 Sorrell Street

Parramatta NSW, 2150

TEL 02 9204-6111 FAX 02 9204-6122

Belgique/België

Bose N.V., Limesweg 2, B-3700 Tongeren

TEL 012-390800 FAX 012-390840

Danmark

Bose A/S, Industrivej 7, 2605 Brøndby

TEL 4343-7777 FAX 4343-7818

Deutschland

Bose GmbH, Max-Planck-Straße 36d

D-61381 Friedrichsdorf

TEL 06172-71040 FAX 06172-710419

France

Bose S.A., 6, rue Saint Vincent

78100 Saint Germain en Laye

TEL 01-30616363 FAX 01-30614105

India

Bose Corporation India Private Limited

W-16, Greater Kailash-II

New Delhi 110 048

TEL (011) 648 4462 FAX (011) 648 4463

Ireland

Bose Corporation

Carrickmacross, Co Monaghan

TEL (042) 9661988 FAX (042) 9661998

La page est en cours de chargement...

Bose Speaker System 149393 Manuel utilisateur

Marque: Bose

Modèle: Speaker System 149393

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Bose Speaker System 149393 User manual

Bose Speaker System 149393 Manuel utilisateur

Bose Speaker System 149393 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents