Powr-Flite PV090-W12-U Le manuel du propriétaire

Marque: Powr-Flite

Modèle: PV090-W12-U

Catégorie: Aspirateurs

Taper: Le manuel du propriétaire

PV090-W12-U

Operating Instructions

Solar Reach™

CONTENTS

Getting Started

Introduction ................................................................................................................................................3

Warranty ......................................................................................................................................................3

Grounding Instructions .......................................................................................................................... 4

Important Safety Instructions ..............................................................................................................5

Parts Identification ...................................................................................................................................7

Operation

Attach the Handle to the Vacuum .................................................................................................... 8

ON/OFF Pedal .......................................................................................................................................... 8

Adjust the Handle .................................................................................................................................... 8

Attach the Cord to the Retainer Hook ............................................................................................ 9

Nozzle Height ............................................................................................................................................ 9

Edge Cleaning ........................................................................................................................................... 9

Cleaning with On-Board Tools ........................................................................................................... 9

Maintenance

Full Bag Indicator ....................................................................................................................................10

Change the Vacuum Bag .....................................................................................................................10

Secondary Filter ....................................................................................................................................... 11

Change the Filters ...................................................................................................................................11

Remove the Bottom Plate ..................................................................................................................12

Replace the Belt ...................................................................................................................................... 12

Thermal Protector ..................................................................................................................................13

Troubleshooting ...................................................................................................................................... 13

For Best Performance ........................................................................................................................... 13

Record Of Purchase ............................................................................................................................... 14

INTRODUCTION

Your new Powr-Flite unit is a high quality, precision-made product. All parts used in

the manufacturing of this unit have passed rigid quality control standards prior to

assembly. Please safeguard the original receipt/invoice given at the time of purchase.

If you experience any problems with your unit during the warranty period, the original

receipt/invoice will act as proof of purchase.

Upon receipt, inspect outer box for exterior damage. Unpack all internal parts,

ensure all items are present according to the owner’s manual, and review

components for damage.

Each unit is tested and thoroughly inspected prior to shipping. If damage is

discovered, immediately notify the transportation company that delivered your

machine and request an inspection. As a manufacturer, we are unable to act upon

any claim for concealed damage and you must originate the claim. Be sure to keep

the carton, packing inserts, and carrier’s receipt until the inspector has verified

your claim.

Warranty

Please visit https://www.powr-flite.com/warranty-registration

to learn more about your warranty and our warranty policy.

Warning Labels

Prior to operating the unit, read and understand completely this

owner’s manual paying special attention to warning labels. These

labels indicate a potentially hazardous situation that could result

in death or serious injury if not avoided. Use only as described in

this manual.

Important

There are no owner serviceable parts inside this machine.

Removal of screws and accessing internal components will

void all warranty claims.

GROUNDING INSTRUCTIONS

DANGER: Improper use of the grounding plug can result in a risk of electric shock.

WARNING!

Improper connection of the equipment-grounding conductor can result in a risk of

electric shock. Check with a qualified electrician or service person if you are in doubt

as to whether the outlet is properly grounded. DO NOT modify the plug provided

with the appliance. If it will not fit the outlet, have a proper outlet installed by a

qualified electrician.

GROUNDING METHODS

This appliance must be grounded. If it should malfunction or breakdown, grounding

provides a path of least resistance for electric current to reduce the risk electric

shock. This machine is equipped with a cord having an equipment-grounding

conductor and grounding plug. The plug must be inserted into an appropriate

outlet that is properly installed and grounded in accordance with all local codes and

ordinances.

This appliance is for use on a nominal 115-volt circuit, and has a grounding plug that

looks like the plug illustrated in sketch A.

GROUNDING

OUTLET

GROUNDING

OUTLET BOX

IMPORTANT SAFETY INSTRUCTIONS

READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE USING THIS UNIT

Read and understand this owner’s manual and all labels on the unit before operating.

Safety is a combination of common sense,staying alert, and knowing how your

unit works. Use this unit only as described in this manual. Use only manufacturer’s

recommended attachments. To reduce the risk of personal injury or damage to your

unit use only recommended accessories.

WARNING To avoid fire, DO NOT use with a flammable or combustible liquid

or floor cleaner.

WARNING To avoid electric shock, DO NOT expose to rain. Store Indoors.

When using this unit, basic precautions should always be followed, including the

following:

• DO NOT leave unit when plugged in. Unplug from outlet when not in use and

before servicing.

• DO NOT allow unit to be used as a toy. Close attention is necessary when used

around or near children.

• Use only as described in this manual. Use only manufacturer’s recommended

attachments.

• DO NOT use with damaged cord or plug. If unit is not working properly because

it has been dropped, dropped into water, left outdoors, or damaged in any way,

contact a service center

• DO NOT handle plug or appliance with wet hands.

• DO NOT put any objects into openings.

• DO NOT use with any opening blocked: keep free of dust, lint, hair, or anything that

may reduce air flow.

• Keep hair, loose clothing, fingers, and all parts of body away from openings and

moving parts.

• DO NOT pick up anything that is smoking or burning such as cigarettes, matches,

or hot ashes.

• DO NOT use to pick up hazardous chemicals.

• Turn off all controls before unplugging.

• DO NOT use to pick up flammable or combustible liquids such as gasoline or use in

areas where they may be present.

• DO NOT use where oxygen or anesthetics are used.

• Replace damaged or worn parts immediately with genuine original equipment parts

to maintain safety.

• This unit must be connected to a properly grounded outlet only. See grounding

instructions.

• DO NOT use equipment out of doors or in the rain.

• DO NOT use equipment near or around flammable or explosive materials, fuels, or

solvents.

• DO NOT allow the unit to freeze.

• Anyone designated to operate this equipment must, without fail, read and

thoroughly understand all instructions and precautions prior to use.

• Do not operate in standing water.

• Do not operate equipment under any unsafe condition.

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

State of California Proposition 65 Warnings

WARNING: This product contains one or more chemicals

known to the state of California to cause cancer.

WARNING: This product contains one or more

chemicals known to the state of California to cause

birth defects or other reproductive harm.

Intended Use

Do NOT modify this unit in any way or adapt it for any use.

Modification of this unit in any way will void all warranties

and could create safety hazards.

PARTS IDENTIFICATION

Replacement Bags, Belts, and Filters

• Genuine Powr-Flite HEPA Media Bags - Part # X1999, 25 per carton

• Genuine Belt - Part # B014-6900

• Filter Pack, Pre and Post Filter Set - Part # X0909

Telescopic

Wand

Airflow/Check

Bag Indicator

Stretch Hose

Hose Handle

Release Button

Bag Compartment

Cover Latch

Handle Tube

Furniture Guard

Nozzle

Handle Grip

Nozzle Hose

ON/OFF

Pedal

Dusting

Brush

Easy Carry

Handle

Power Cord

Metal Cord Hook

Cord Storage

Hooks

Crevice Tool

Quick

Clean-out

Port

Handle

Release

Pedal

Fig. 1

OPERATION

ON/OFF Pedal

1. To turn the vacuum on, push the power pedal on

the right side of the vacuum nozzle from the user’s

perspective (Fig. 1).

2. To turn the vacuum off, push the pedal again.

How to Adjust the Handle

1. To release the handle, step on the handle release pedal

on the left side of the vacuum cleaner nozzle from the

user’s perspective and pull back the handle (Fig.1).

2. Upright position – for storage or when cleaning tools

are used (Fig. 2). Handle locks in this position.

3. Middle position – for normal cleaning (Fig. 3).

4. Low position – for cleaning under furniture (Fig. 4).

The handle on this vacuum cleaner can be set to one of three positions – upright,

middle or low.

How to Attach the Handle to the Vacuum Cleaner

The vacuum and the handle are packed separately.

1. After first removing the handle screw, slide the handle into the

slot on top of the vacuum cleaner.

2. Line up the small hole on the handle with the small hole on the

vacuum cleaner and insert the screw. Make sure the screw is

tightened securely (Fig. 1).

Fig. 1

Fig. 2

Fig. 1

Fig. 3 Fig. 4

Fig. 1 Fig. 2

OPERATION

How to Attach the Cord to the

Retainer Hook on the Handle

1. Create a loop in the power cord and push

it through the slot and over the hook of

the cord retainer (Fig. 1).

2. Pull down on the power cord to remove

any slack (Fig. 2).

How to Adjust the Height Adjustment

The height adjust dial should be on the LOW setting at all times for optional cleaning

performance on commercial carpet (Fig. 1).

Edge Cleaning Feature

The edge cleaning feature provides improved cleaning near walls and stationary

furniture. For maximum edge cleaning, position the right side of the vacuum from

the user’s perspective near walls or stationary furniture.

Cleaning with On-Board Tools

Your vacuum cleaner is equipped with on-board

cleaning tools, including a telescopic wand, stretch

hose, dusting brush and a crevice tool.

1. To use the cleaning tools, lift the hose handle

straight up from the vacuum (Fig. 1).

2. Extend the wand by pulling the button back and

pulling the smaller wand out of the larger wand

(Fig. 2).

3. Attach any of the on-board tools to the end of the

wand, or if you do not need the wand, any tool can

be connected directly onto the hose handle.

Fig. 1

Fig. 2

Use LOW Setting

for Commercial Carpet

Use LOW Setting

for Commercial Carpet

MAINTENANCE

Full Bag Indicator

The full bag indicator is designed to show when the

bag is full or when there is a clog in the vacuum.

• If the red indicator (Fig. 1) appears:

• Change the vacuum bag

• If the vacuum bag is not full, but the full bag

indicator is red, check the hose for a clog.

• When cleaning with a tool (dusting brush or

crevice tool), the red indicator may appear.

In this case, continue cleaning.

How to Change the Vacuum Bag

1. Unplug the vacuum cleaner. Remove

the bag compartment cover (Fig. 1).

2. Remove the bag from the bag holder

by grasping the sides of the bag

collar and pulling straight off. Attach

a new vacuum bag by pushing the

collar onto the inlet (Fig. 2).

3. Pull out the bottom corners of the

new vacuum bag to expand the bag

capacity (Fig. 3).

4. Reinsert the tab on the end of the

bag compartment cover into the

groove on the bag compartment

housing. Press the bag compartment

cover into place, closing it tightly.

Always operate the vacuum cleaner with a vacuum bag installed.

Bags should be changed when they are 2/3 full.

Fig. 1

Fig. 1 Fig. 2

Fig. 3

MAINTENANCE

Your vacuum cleaner is equipped with a secondary

filter and a Final filter. These filters capture fine

dust particles and protect the motor from dirt.

Accumulated dirt in the bag compartment will

be collected on the filters and may restrict motor

performance. It is important to change the filters

regularly — approximately once a year or as

needed.

How to Change the Secondary Filter

1. Unplug the vacuum cleaner. Remove the bag

compartment cover and remove the vacuum

bag.

2. Remove the secondary filter by sliding it out

from under the bag supporter (Fig. 1).

3. Insert a new filter, replace the bag and bag

compartment cover.

How to Change the Final Filter

1. Unplug the vacuum cleaner. Remove the filter

cover below the dust compartment cover

(Fig. 2).

2. Remove the filter from the front of the vacuum

(Fig. 3).

3. Vacuum or brush off any dirt on the filter.

If needed, foam filter can be rinsed with warm

water to clean. Allow the filter to air dry for 24

hours before re-installing in the vacuum.

Fig. 3

Fig. 2

Fig. 1

MAINTENANCE

CAUTION: First unplug the vacuum cleaner.

How to Remove the Bottom Plate

1. Place the vacuum cleaner in the lowest

position by stepping on the handle release

pedal (see “How to Adjust the Handle” on

page 8). Turn the vacuum over on a flat

surface, exposing the bottom plate.

2. Remove the five screws holding the

L-shaped bottom plate in place (Fig. 1).

3. Remove the bottom plate.

How to Replace the Belt

1. Turn over the unit and remove the bottom

plate as described above.

2. Lift out the brush roll and remove the old

belt (Fig. 2).

3. Loop the new belt around the drive shaft

(Fig. 3) and the raised ring between the

bristles on the brush roll (Fig. 4).

4. Pull the brush roll forward (against the pull

of the belt) and reinsert the ends back into

the nozzle (Fig. 5) making sure to line up the

end opposite the belt so the flat edges slide

down properly.

5. Turn the brush roll by hand, making sure

the belt is not twisted and all rotating parts

move smoothly.

6. Replace the bottom plate and the

five screws.

Screw

points

Drive

shaft

MAINTENANCE

TROUBLESHOOTING

Thermal Protector

Your Powr-Flite vacuum cleaner is equipped with a thermal protector designed to

protect your vacuum cleaner from overheating due to restricted airflow (i.e. clogged

hose). Should this situation occur, the thermal protector will automatically shut off

the motor to prevent damage.

How to Reset the Thermal Protector

1. Unplug the vacuum cleaner.

2. Allow the vacuum cleaner to cool at least 30 minutes.

3. Check for blockages, change the vacuum bag and clean or replace the filters.

4. Plug in the vacuum cleaner and begin using.

For Best Performance

• Keep machine and all accessories clean and in good operating condition.

• Replace the bag when it is 2/3 full.

• Replace the filters once a year or as needed.

• Always use genuine Powr-Flite filters and parts, as use of other products may

result in poor cleaning or filtration performance. Powr-Flite filtration products

are designed for maximum performance.

• Store machine carefully in a dry area.

• For optimum cleaning performance and safety, follow your owner’s manual.

Problem Check Point Possible Solution

Suction power is

weak.

• Vacuum bag

• Wand or hose

• Filters

• If the vacuum bag is 2/3 full, replace it.

• If clogged or blocked, remove the object.

• Clean or replace filters.

The vacuum does

not work. • Power cord Insert the power plug firmly into an

electrical outlet.

Sudden loss of

power. • Thermal reset

Turn off vacuum and unplug from

electrical outlet. Let vacuum cool down

for at least 30 minutes before turning back

on. Check for clogs. Replace vacuum bag.

Dirt and debris are

blowing through

exhaust vent.

• Filters Make sure filters are clean, dry and

installed correctly.

All other service should be performed by an authorized service center.

P-OMPV090-W12-U 02/2023

Powr-Flite

3101 Wichita Court

Ft. Worth, TX 76140-1755

Phone: 817-551-0700

WWW.POWR-FLITE.COM

Serial Number:

Purchase Date:

Dealer:

Phone Number:

Record of Purchase

PV090-W12-U

Instrucciones de operación

Solar Reach™

CONTENIDO

Getting Started

Introducción .............................................................................................................................................. 17

Garantía ...................................................................................................................................................... 17

Instrucciones de conexión a tierra ................................................................................................... 18

Importantes instrucciones de seguridad .......................................................................................19

Identificación de piezas ........................................................................................................................21

Operación

Cómo conectar el mango a la aspiradora .................................................................................... 22

Pedal de encendido/apagado .......................................................................................................... 22

Cómo ajustar el mango ....................................................................................................................... 22

Cómo conectar el cable al gancho de retención en el mango ............................................23

Cómo ajustar el ajuste de altura ......................................................................................................23

Función de limpieza de bordes ........................................................................................................ 23

Limpieza con herramientas incorporadas ....................................................................................23

Mantenimiento

Indicador de bolsa llena ......................................................................................................................24

Cómo cambiar la bolsa de la aspiradora ......................................................................................24

Cómo cambiar el filtro secundario ..................................................................................................25

Còrno cambiar el filtro final ...............................................................................................................25

Cómo quitar la placa inferior ............................................................................................................26

Cómo reemplazar la correa ...............................................................................................................26

Protector térmico .................................................................................................................................. 27

Solución de problemas ........................................................................................................................ 27

Para un mejor rendimiento................................................................................................................. 27

Registro de compra ..............................................................................................................................28

INTRODUCCIÓN

Su nueva unidad Powr-Flite es un producto de alta calidad fabricado con precisión.

Todas las piezas utilizadas en la fabricación de esta unidad han pasado estrictos

estándares de control de calidad antes del montaje. Conserve el recibo o la factura

original entregados al momento de la compra. Si experimenta algún problema con su

unidad durante la vigencia de la garantía, el recibo o factura original actuará como

prueba de compra.

Al recibir la unidad, inspeccione la caja exterior en busca de daños exteriores.

Desembale todas las piezas internas, asegúrese de que todos los elementos estén

presentes de acuerdo con el manual del propietario y revise los componentes en

busca de daños.

Cada unidad se prueba e inspecciona minuciosamente antes del envío. Si descubre

daños, notifique inmediatamente a la empresa de transporte que entregó su máquina

y solicite una inspección. Como fabricante, no podemos responder a ninguna

reclamación por vicios ocultos y usted debe iniciar la reclamación. Asegúrese de

guardar la caja de cartón, los folletos y el recibo del transportista hasta que el

inspector haya verificado su reclamación.

Garantía

Visite https://www.powr-flite.com/warranty-registration

para obtener más información sobre su garantía y nuestra

política de garantía.

Etiquetas de advertencia

Antes de operar la unidad, lea y comprenda completamente

este manual del propietario, prestando especial atención a las

etiquetas de advertencia. Estas etiquetas indican una situación

potencialmente peligrosa que podría provocar la muerte o lesiones

graves si no se evita. Use solo como se describe en este manual.

Importante

No hay ninguna pieza reparable por el propietario dentro de esta

máquina. La extracción de tornillos y el acceso a los componentes

internos anularán todas las reclamaciones de garantía.

INSTRUCCIONES DE CONEXIÓN A TIERRA

PELIGRO: el uso inadecuado del enchufe con conexión a tierra puede resultar en un

riesgo de descarga eléctrica.

¡ADVERTENCIA!

La conexión incorrecta del conductor de conexión a tierra del equipo puede

resultar en un riesgo de descarga eléctrica. Consulte con un electricista calificado o

personal de servicio si tiene dudas sobre si el tomacorriente está conectado a tierra

correctamente. NO modifique el enchufe provisto con el artefacto. Si no encaja en el

tomacorriente, haga que un electricista calificado instale un tomacorriente adecuado.

MÉTODOS DE PUESTA A TIERRA

Este aparato debe estar conectado a tierra. En caso de mal funcionamiento o avería,

la conexión a tierra proporciona una vía de menor resistencia para la corriente

eléctrica, reduciendo así el riesgo de descarga eléctrica. Esta máquina está equipada

con un cable que tiene un conductor de conexión a tierra del equipo y un enchufe de

conexión a tierra. El enchufe debe insertarse en una toma de corriente apropiada que

esté correctamente instalada y conectada a tierra de acuerdo con todos los códigos

y ordenanzas locales.

Este aparato es para usar en un circuito nominal de 115 voltios y tiene un enchufe con

conexión a tierra que se parece al enchufe ilustrado en el dibujo A.

CLAVIJA CON

CONEXIÓN A TIERRA

TOMA DE CORRIENTE

CON CONEXIÓN A

TIERRA

CAJA DE TOMA

DE CORRIENTE

CON CONEXIÓN

A TIERRA

IMPORTANTES INSTRUCCIONES DE SEGURIDAD

LEA Y COMPRENDA TODAS LAS INSTRUCCIONES ANTES DE UTILIZAR ESTA UNIDAD

Lea y comprenda este manual del propietario y todas las etiquetas de la unidad antes

de operarla. La seguridad es una combinación de sentido común, mantenerse alerta

y saber cómo funciona su unidad. Utilice esta unidad solo como se describe en este

manual. Utilice únicamente los accesorios recomendados por el fabricante. Para

reducir el riesgo de lesiones personales o daños a su unidad, utilice únicamente los

accesorios recomendados.

ADVERTENCIA para evitar incendios, NO lo use con un líquido inflamable o

combustible, o limpiador de pisos.

ADVERTENCIA Para evitar descargas eléctricas, NO lo exponga a la lluvia. Almacene

en interiores.

Al usar esta unidad, siempre se deben tener precauciones básicas, incluidas las siguientes:

• NO deje sola la unidad cuando esté enchufada. Desenchufe la aspiradora de la toma de

corriente cuando no esté en uso y antes de hacerle el mantenimiento.

• NO permita que la unidad se use como un juguete. Es necesario prestar mucha atención

cuando se usa alrededor o cerca de niños.

• Use solo como se describe en este manual. Utilice únicamente los accesorios

recomendados por el fabricante.

• NO debe utilizarse con un cable o enchufe dañado. Si la unidad no funciona

correctamente porque se cayó, se cayó al agua, se dejó al aire libre o se dañó de alguna

manera, comuníquese con un centro de servicio.

• NO manipule el enchufe ni el aparato con las manos mojadas.

• NO introduzca ningún objeto en las aberturas.

• NO debe usarse si alguna de sus aberturas está bloqueada; mantenga libre de polvo,

pelusa, cabello, o cualquier cosa que pueda reducir el flujo de aire.

• Mantenga el cabello, la ropa holgada, los dedos y todas las partes del cuerpo alejados de

las aberturas y las partes móviles.

• NO recoja nada que esté humeando o ardiendo, como cigarrillos, fósforos o cenizas

calientes.

• NO debe usarse para recoger productos químicos peligrosos.

• Apague todos los controles antes de desenchufar.

• NO debe usarse para recoger líquidos inflamables o combustibles como la gasolina, ni en

áreas donde estos productos puedan estar presentes.

• NO debe usarse donde haya oxígeno o anestésicos.

• Reemplace las piezas dañadas o desgastadas de inmediato con piezas genuinas del

equipo original para mantener la seguridad.

• Esta unidad debe conectarse únicamente a un tomacorriente correctamente conectado

a tierra. Consulte las instrucciones de conexión a tierra.

• NO use el equipo al aire libre o bajo la lluvia.

• NO use el equipo cerca o alrededor de materiales, combustibles o solventes inflamables

o explosivos.

• NO permita que la unidad se congele.

• Cualquier persona designada para operar este equipo debe, sin falta, leer y comprender

completamente todas las instrucciones y precauciones antes de su uso.

• No opere en agua estancada.

• No opere el equipo bajo ninguna condición insegura.

GUARDE ESTAS INSTRUCCIONES

IMPORTANTES INSTRUCCIONES

DE SEGURIDAD

Advertencias de la Proposición 65

del estado de California

ADVERTENCIA: este producto contiene una

o más sustancias químicas conocidas en el estado

de California como causantes de cáncer.

ADVERTENCIA: este producto contiene una o más sustancias

químicas reconocidas por el estado de California como causantes

de defectos de nacimiento u otros daños reproductivos.

Uso previsto

NO modifique esta unidad de ninguna manera ni la adapte para

ningún uso. La modificación de esta unidad de cualquier manera

anulará todas las garantías y podría crear riesgos para la seguridad.

La page charge ...

Powr-Flite PV090-W12-U Le manuel du propriétaire

Marque: Powr-Flite

Modèle: PV090-W12-U

Catégorie: Aspirateurs

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Powr-Flite PV090-W12-U Owner's manual
español: Powr-Flite PV090-W12-U El manual del propietario

Powr-Flite PV090-W12-U Le manuel du propriétaire

Powr-Flite PV090-W12-U Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents