Philips AVENT AVENT SCD525 Manuel utilisateur
- Catégorie
- Babyphones
- Taper
- Manuel utilisateur
6
Some of the following information may not apply to your particular product; however, when using
baby monitor equipment, basic safety precautions should always be followed to reduce the risk of
re, electric shock and injury to persons, including the following:
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus
(including ampliers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades with one wider than the other. A grounding-type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided for your safety. If the provided
plug does not t into your outlet, consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
Only use attachments/accessories specied by the manufacturer.
Unplug this appliance during lightning storms or when not used for long periods of time.
Refer all servicing to qualied service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped. For assistance visit our website www.philips.
com/AVENT or call 1-800-54-AVENT (1-800-542-8368).
This baby monitor is intended as an aid. It is not a substitute for responsible and proper adult
supervision and should not be used as such.
Use this appliance only for its intended use as described in this manual.
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol
cleaners.
Products should not be used while you are in a bathtub, shower or pool. Immersion of the
product in water could cause an electrical shock.
This product should be operated only from the type of power source indicated on the type
plate of the adapters (A13,B10). If you are not sure of the type of power supply to your home,
consult your dealer or local power company.
The apparatus shall not be exposed to dripping or splashing and no objects lled with liquids,
such as vases, shall be placed on the apparatus.
Do not overload wall outlets and extension cords as this can result in the risk of re or electric
shock.
Never push objects of any kind into this product through casing slots as they may touch
dangerous voltage points or short out parts that could result in a risk of re or electric shock.
Never spill liquid of any kind on the product.
To reduce the risk of electric shock, do not disassemble this product, but visit our website www.
philips.com/AVENT or call 1-800-54-AVENT (1-800-542-8368) for assistance. Opening or
removing covers (except battery compartment lids) may expose you to dangerous voltage or
other risks. Incorrect reassembly can cause electric shock when the appliance is subsequently
used.
4222.005.0010.1.indd 6 29-03-10 14:38
To prevent strangulation with power cord, never place monitor within reach of child. Do not use
with extension cords.
Do not place any sources of danger on the apparatus (like liquid-lled objects, lighted candles
etc.).
Use only the type and size of batteries specied in the user manual.
Do not dispose of batteries in re. They may explode. Check with local regulations for possible
special disposal instructions.
Exercise care in handling batteries in order not to short out the batteries with conducting
materials such as rings, bracelets and keys. Overcharging, short circuiting, reverse charging,
mutilation, or incineration of batteries must be avoided to prevent one or more of the following
occurrences: release of toxic materials, release of hydrogen and/or oxygen gas, rise in surface
temperature.
Do not attempt to recharge batteries provided with or identied for use with this product that
are not intended to be charged. The batteries may leak corrosive electrolyte or explode.
Do not attempt to rejuvenate the batteries provided with or identied for use with this product
by heating them. Sudden release of battery electrolyte may occur, causing burns or irritation to
eyes or skin.
If and when necessary, the batteries must be replaced with identical new ones from the same
manufacturer. If a battery to be replaced is connected with other batteries in series, it is
recommended that the other batteries be replaced with new ones at the same time.
Reverse polarity installation of the batteries in the end product must be avoided. Reverse
insertion of batteries can cause charging, and that may result in leakage or explosion.
Remove batteries from this product if you store the product over 30 days because the batteries
could leak and damage the product.
Discard ‘dead’ batteries as soon as possible since ‘dead’ batteries are more likely to leak in a
product. If a battery has leaked or vented, it should be replaced immediately using protective
gloves.
Do not store this product, or the batteries provided with or identied for use with this product,
in high-temperature areas. Batteries that are stored in a freezer or refrigerator for the purpose
of extending shelf life should be protected from condensation during storage and defrosting.
Batteries should be stabilized at room temperature prior to use after cold storage.
If your product uses rechargeable batteries, charge the batteries only in accordance with the
instructions and limitations specied in the user manual.
There is a risk of explosion if batteries are replaced with an incorrect type. For the
always use the SCD525 NiMh battery pack supplied with the appliance.
-
-
7
4222.005.0010.1.indd 7 29-03-10 14:38
Adapter for baby unit:
- Input: 100-240VAC 50-60Hz
- Output: 7.5 VDC 400 mA
- Adapter no. S004LU0750040
Adapter for charger:
- Input: 100-240 VAC 50/60Hz
- Output: 7.5VDC 500mA
- Adapter no. SSA-5W-09 US 075050F
The socket-outlet shall be installed near the equipment and shall be easily accessible.
For the baby unit, only use 1.5V AA alkaline batteries (batteries not supplied).
For the parent unit, only use the NiMh rechargeable battery pack supplied with the appliance.
Dispose of used batteries according to the instructions.
The term ‘IC’ before the certication number signies that Industry Canada technical specications
were met.This certication means that the equipment meets certain radio communications and
operational requirements. This device complies with Part 15 of the FCC Rules and RSS-213 of
Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules and ICES-003 of Industry Canada. These limits are designed
to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of 7 3/4
inches / 20 centimeters between the radiator and your body. For handheld operation, this
equipment has been tested and meets the FCC RF exposure guidelines. For body-worn operation,
this product has been tested and meets the FCC RF exposure guideline when used with the belt
clip or neck strap supplied with this product. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter. Use of other accessories may not ensure
compliance with FCC RF exposure guidelines. This equipment also complies with Industry Canada
RSS-102 with respect to Canada’s Health Code 6 for Exposure of Humans to RF Fields.
Any repairs or alterations made by the user to the equipment may void the warranty and
compliance of the equipment. Changes or modications made to this equipment not expressly
approved by Philips AVENT may void the FCC authorization to operate this equipment. For
assistance visit our website www.philips.com/AVENT or call 1-800-54-AVENT (1-800-542-8368).
8
4222.005.0010.1.indd 8 29-03-10 14:38
Congratulations on your purchase and welcome to Philips AVENT! To fully benet from the support
that Philips AVENT offers, register your product at www.philips.com/welcome.
Philips AVENT is dedicated to producing caring, reliable products that give parents the reassurance
they need. This Philips AVENT baby monitor provides round-the-clock support by ensuring you can
always hear your baby clearly without any distracting noise. The DECT technology guarantees zero
interference from other wireless appliances and a crystal clear signal between the baby unit and the
parent unit. The temperature sensor enables you to monitor the temperature in your baby’s room,
and offers you personalized settings to help keep your baby’s room comfortable.
The temperature sensor enables you to monitor the temperature in your baby’s room, and offers
you personalized settings to help keep your baby’s room comfortable.
On/off button 3
Slot for belt clip
TALK button
MENU button
LINK light
Microphone
Loudspeaker
Menu and volume +/– buttons
OK button
Display
Sound level lights
Belt clip
Adapter
Small appliance plug
Socket for small appliance plug
Charger
Charging light
Compartment for rechargeable battery pack
Neck strap
Lid of compartment for rechargeable battery pack
Rechargeable battery pack (included)
Opening for neck strap
On/off button 3
PAGE button
Play/stop button E
Lullaby button K
Battery light T
Nightlight button Q
Power-on light
Volume +/– buttons
Microphone
Adapter
Large appliance plug
Loudspeaker
Temperature sensor
Socket for large appliance plug
9
4222.005.0010.1.indd 9 29-03-10 14:38
Compartment for non-rechargeable batteries
Lid of compartment for non-rechargeable batteries
Non-rechargeable batteries (not included)
Nightlight symbol
ECO symbol
Lullaby symbol
Sound alert
Temperature alert
Battery symbol
Room temperature indication (Celcius or Fahrenheit)
For other display indications and volume/sensitivity levels, see chapters ‘Features’ and ‘Menu options’.
- Read this user manual carefully before you use the appliance and save it for future reference.
- Never immerse any part of the baby monitor in water or any other liquid.
- Do not place the appliance where water or any other liquid can drip or splash onto it.
- Never put any object containing liquid on top of the baby unit.
- Check if the voltage indicated on the adapters of the baby unit and the charger corresponds to
the local voltage before you connect the appliance.
- Only use the adapter supplied to connect the baby unit to the power outlet.
- Only use the charger and adapter supplied to charge the parent unit.
- The adapters contain a transformer. Do not cut off the adapters to replace them with other
plugs, as this causes a hazardous situation.
- If the adapters are damaged, always have them replaced with one of the original type in order
to avoid a hazard. For the correct type, see chapter ‘Replacement’.
- If the charger of the parent unit is damaged, always have it replaced with one of the original
type.
- Never use the baby monitor in moist places or close to water.
- Use and store the appliance at a temperature between 50°F (10°C) and 95°F (35°C).
- Children should be supervised to ensure that they do not play with the appliance.
- Do not expose the baby unit and parent unit to extreme cold or heat or to direct sunlight. Do
not put the baby unit and the parent unit close to a heating source.
- Make sure the baby unit and the cord are always out of reach of the baby (at least 3 feet/1
meter away).
- Never place the baby unit inside the baby’s bed or playpen.
- Never cover the parent unit and the baby unit with anything (e.g. a towel or blanket).
- Always place non-recheargeable batteries of the correct type in the baby unit.
- Always place a rechargeable battery pack of the correct type in the parent unit.
- If you place the parent unit next to a transmitter or other DECT appliance (e.g. a DECT
telephone or wireless router for the internet), the connection with the baby unit may be lost.
Move the baby monitor further away from the other wireless appliances until the connection is
restored.
- Switched-on mobile phones in the vicinity of the baby monitor may cause interference with the
baby monitor.
- Radio interference is inevitable and may have an effect on the sound quality of the baby monitor.
- This baby monitor is intended as an aid. It is not a substitute for responsible and proper adult
supervision and should not be used as such.
- Take every precaution to make sure that your baby can sleep safely.
10
4222.005.0010.1.indd 10 29-03-10 14:38
- The temperature sensor only measures the temperature in the baby room. It cannot be used
to control or adjust the temperature in the baby room.
- This monitor is not intended to be used as a medical monitor and its use should not replace
adult supervision.
You can use the baby unit corded or on non-rechargeable batteries. Even if you are going to use the
unit corded, we advise you to insert non-rechargeable batteries. This guarantees automatic back-up
in case of power failure.
1 Put the large appliance plug in the baby unit and put the adapter in a wall outlet (Fig. 4).
The baby unit runs on four 1.5V R6 AA batteries (not included). We advise you to use Philips LR6
PowerLife batteries or an equivalent type.
Do not use rechargeable batteries, as the baby unit does not have a charging function.
Place batteries in the baby unit if you do not want to use it corded or if you want to be sure of
backup power in case of power failure. Replace the batteries when the baby unit indicates that the
batteries are low (the empty battery symbol ashes on the display and the text ‘Battery low’
appears).
Unplug the baby unit and make sure your hands and the unit are dry when you insert the
non-rechargeable batteries.
1 Remove the lid of the compartment for non-rechargeable batteries. (Fig. 5)
2 Insert four non-rechargeable batteries (Fig. 6).
Note: Make sure the + and - poles of the batteries point in the right direction.
3 Reattach the lid. (Fig. 7)
Note: When the batteries are low, the battery light on the baby unit ashes red.
The parent unit comes with a NiMh 850mAh rechargeable battery pack.
Charge the parent unit before you use it for the rst time or when the parent unit indicates that the
battery pack is low (the empty battery symbol ashes on the display and the parent unit beeps). The
parent unit starts indicating that the battery pack is low 30 minutes before the battery pack
is completely empty.
Note: If the battery pack is completely empty, the parent unit automatically switches off and loses
contact with the baby unit.
1 Remove the lid of the compartment for the rechargeable battery pack (Fig. 8).
2 Insert the rechargeable battery pack (Fig. 9).
Note: Make sure the + and - poles of the battery pack point in the right direction.
3 Reattach the lid (Fig. 10).
4 Insert the small appliance plug into the charger, put the adapter in a power outlet and place
the parent unit in the charger (Fig. 11).
,The charging light on the charger goes on.
11
4222.005.0010.1.indd 11 29-03-10 14:38
,The display shows a charging battery symbol to indicate that the parent unit is charging.
5 Leave the parent unit in the charger until the battery pack is fully charged.
,During charging, the charging light on the charger stays on.
,When the battery pack is fully charged, the display of the parent unit shows a full battery
symbol T.
- When you charge the parent unit for the rst time or after a long period of non-use, switch it
off and let it charge continuously for at least 10 hours.
- Charging normally takes 8 hours, but it takes longer when the parent unit is switched on while
charging. To keep the charging time as short as possible, switch off the parent unit during
charging.
- When the battery pack is fully charged, the parent unit can be used cordlessly for up to 24
hours.
Note: When the parent unit is charged for the rst time, the operating time is less than 24 hours. The
battery pack only reaches its full capacity after you have charged and discharged it four times.
Note: When the parent unit is not in the charger, the battery pack gradually discharges, even when the
parent unit is switched off.
Use the baby monitor for its intended household use as described in this manual.
1 Place the parent unit and the baby unit in the same room to test the connection (Fig. 12).
Make sure the baby unit is at least 3 feet/1 meter away from the parent unit.
2 Press and hold the on/off button 3 on the baby unit until the green power-on light goes
on. (Fig. 13)
Note: The power-on light always lights up green, even when there is no connection with the parent unit.
,The nightlight lights up briey and then goes out again.
,The battery light T lights up briey and then goes out again. (Fig. 14)
3 Press and hold the on/off button 3 on the parent unit until the sound level lights light up
briey. (Fig. 15)
,The display goes on and the battery symbol appears on the display (Fig. 16).
,The LINK light ashes red and the message ‘Searching’ appears on the display. (Fig. 17)
,The LINK light on the parent unit turns green and lights up continuously when a connection
has been established between the baby unit and parent unit. The message ‘Linked’ appears on
the display. (Fig. 18)
,After 2 seconds the message ‘Linked’ disappears and the temperature value is shown on the
display. (Fig. 19)
,If no connection is established, the LINK light on the parent unit ashes red. The parent unit
beeps from time to time and the message ‘Searching’ appears on the display, followed by the
message ‘Not Linked’ (Fig. 20).
1 Place the baby unit at least 3 feet/1 meter away from your baby (Fig. 21).
2 Place the parent unit within the operating range of the baby unit. Make sure it is at least 3
feet/1 meter away from the baby unit to avoid acoustic feedback (Fig. 22).
For more information on the operating range, see section ‘Operating range’ below.
The operating range of the baby monitor is 1000 feet/330 metres in open air. Depending on the
surroundings and other disturbing factors, this range may be smaller. Indoors the operating range is
up to 150 feet/50 metres.
12
4222.005.0010.1.indd 12 29-03-10 14:38
Note: If the ECO mode is switched on, the operating range of the baby monitor is also smaller. See
section ‘ECO mode’ in chapter ‘Menu options’.
Dry materials Material thickness Loss of range
Wood, plaster, cardboard, glass
(without metal, wires or lead) < 12in/30cm 0-10%
Brick, plywood < 12in/30cm 5-35%
Reinforced concrete < 12in/30cm 30-100%
Metal grilles or bars < 0.4in/1cm 90-100%
Metal or aluminum sheets < 0.4in/1cm 100%
For wet and moist materials, the range loss may be up to 100%.
The following features are described in chapter ‘Menu options’, as they can only be operated in the
menu of the parent unit:
- Adjusting microphone sensitivity
- Sound alert on/off
- Setting room temperature range (minimum and maximum temperature)
- Temperature alert on/off
- ECO mode on/off
- Setting temperature scale (Fahrenheit or Celcius)
1 Press the volume + or – button on the baby unit until the desired loudspeaker volume for
the baby unit has been reached (Fig. 23).
Note: You can only set the loudspeaker volume on the baby unit when a lullaby is playing.
2 Press the volume + or – button on the parent unit until the desired loudspeaker volume for
the parent unit has been reached (Fig. 24).
,The display gives visual feedback on the volume settings of the parent unit: (Fig. 25)
- Volume switched off/silent baby monitoring
- Minimum volume
- Maximum volume
Note: If the volume is set to a high level, the units consume more power.
You can use the TALK button on the parent unit to talk to your baby (e.g. to comfort your baby).
1 Press and hold the TALK button and talk clearly into the microphone from a distance of
6-12in/15-30cm (Fig. 26).
,The green LINK light starts ashing and the message ‘Talk’ appears on the display.
2 Release the TALK button when you have nished talking.
The parent unit continuously monitors the sound level in your baby´s room and the sound level
lights let you know if there is any activity. If your baby cries, you see the sound level lights light up on
the parent unit.
13
4222.005.0010.1.indd 13 29-03-10 14:38
- As long as the baby unit does not detect a sound, all sound level lights on the parent unit are
out.
- When the baby unit picks up a sound, one or more sound level lights on the parent unit go on.
The number of lights that go on is related to the loudness of the sound picked up by the baby
unit.
1 Press the nightlight button Q on the baby unit to switch on the nightlight. (Fig. 27)
,Q appears on the display of the parent unit.
2 Press the nightlight button Q again to switch off the nightlight.
,The nightlight dims gradually before it goes out completely.
,Q disappears from the display of the parent unit.
Tip: Switch off the nightlight when you operate the baby unit on the non-rechargeable batteries. This
saves power.
If you have misplaced the parent unit and its volume is switched off, you can use the PAGE button
on the baby unit to locate the parent unit.
Note: The paging function only works when the parent unit is switched on.
1 Press the PAGE button on the baby unit (Fig. 28).
,The message ‘Paging’ appears on the display of the parent unit.
,The parent unit produces a paging alert tone.
2 To stop the paging alert tone, press the PAGE button again or press any button on the parent
unit.
1 Press the play/stop button E on the baby unit to play the currently selected
lullaby. (Fig. 29)
,The lullaby starts to play and repeats continuously.
2 To select another lullaby when a lullaby is playing: (Fig. 30)
- Press the lullaby button K on the baby unit.
- Wait 2 seconds for the next lullaby to start.
- If you want another lullaby, press the lullaby button K on the baby unit again.
3 To stop the lullaby, press the play/stop button E on the baby unit again. (Fig. 29)
When the parent unit is out of range of the baby unit, the parent unit beeps from time to time and
the messages ‘Searching’ and ‘Not linked’ appear on the display. The LINK light on the parent unit
ashes red.
Note: The message ‘Not Linked’ also appears on the display of the parent unit when the baby unit is
switched off.
All functions can be operated on the parent unit, but some functions can also be operated on the
baby unit.
14
4222.005.0010.1.indd 14 29-03-10 14:38
Note: Menu functions can only be operated when a connection has been established between the baby
unit and the parent unit.
1 Press the MENU button to open the menu (Fig. 31).
,The rst menu option appears on the display.
2 Use the – and + buttons to select the desired menu option (Fig. 32).
Note: The arrow indicates in which direction you can navigate.
3 Press the OK button to conrm (Fig. 33).
4 Use the + and - buttons to select the desired setting.
5 Press the OK button to conrm.
, The new setting ashes once. The message ‘saved’ also ashes once and then disappears from
the display.
6 Press the MENU button again to exit the menu.
Note: You can only switch the ECO mode on and off in the menu of the parent unit.
You can use the ECO mode to reduce the energy consumption of the appliance. Monitoring your
baby from a small distance requires less transmission power and less electrical power
than monitoring your baby from a large distance. When you monitor your baby from a small
distance, you can activate the ECO mode. In the ECO mode, the appliance consumes
less energy, but still ensures that you can always hear your baby clearly without any distracting noise.
Using the baby monitor in the ECO mode helps you to preserve the environment.
Note: The operating range of the baby monitor when it is operated in the ECO mode is 850 feet/260
meters in open air. Depending on the surroundings and other factor that may cause interference, this
range may be smaller.
1 Select ‘ECO mode’ with the + and - buttons (Fig. 32).
2 Press the OK button to conrm (Fig. 33).
3 If the ECO mode is off, the display shows ‘On?’. Press the OK button to switch on the ECO
mode. If the ECO mode is on, the display shows ‘Off?’. Press the OK button to switch off the
ECO mode.
,If you have set the ECO mode to ‘on’, the parent unit switches off and on again. The ECO
mode symbol appears on the display of the baby unit and the parent unit to indicate that
both units now operate in ECO mode.
Note: The connection between parent and baby unit may be lost when the ECO mode is switched on. If
this happens, the operating range may be too large for the ECO mode. In this case, either reduce the
operating range or switch off the ECO mode.
Note: You can only adjust the microphone sensitivity in the menu of the parent unit.
You can set the microphone sensitivity of the baby unit to the desired level. You can only change the
microphone sensitivity when a connection between the baby unit and the parent unit has been
established, i.e. when the LINK light on the parent unit lights up green continuously.
1 Select ‘Sensitivity’ with the + and - buttons. (Fig. 32)
2 Press the OK button to conrm.
15
4222.005.0010.1.indd 15 29-03-10 14:38
3 Select the desired microphone sensitivity level for the baby unit with the + and -
buttons. (Fig. 34)
Minimum sensitivity level
Maximum sensitivity level
4 Press the OK button to conrm.
,The message ‘Saved’ appears on the display.
Note: When the microphone sensitivity of the baby unit is set to a high level, it picks up more sounds and
therefore transmits more often. As a result, the units consume more power and the operating time of the
battery is shorter.
Note: You can only switch the sound alert on and off in the menu of the parent unit.
This feature allows you to monitor your baby silently. It enables you to switch off the volume on
your parent unit and still be alerted if your baby cries.
If the sound alert is switched on, the parent unit beeps as soon as the fourth sound level light lights
up blue while the volume is switched off. In addition, the backlight of the parent unit display goes on
and the sound alert symbol ( q) ashes on the display.
1 Select ‘Alert settings’ with the + and - buttons. (Fig. 32)
2 Press the OK button to conrm.
3 Select ‘Sound alert’ with the + and - buttons.
4 Press the OK button to conrm.
5 If the alert is off, the display shows ‘On?’. Press the OK button to switch on the alert. If the
alert is on, the display shows ‘Off?’. Press the OK button to switch off the alert.
,If you have set the sound alert to ‘on’, the sound alert symbol ( q) appears on the display of
the parent unit.
Note: You can only adjust the temperature range in the menu of the parent unit.
A baby will sleep comfortably in a room heated to a temperature between 61°F (16°C) and 68°F
(20°C). This is important, since a baby cannot regulate its body temperature as well as an adult. A
baby needs more time to adjust to temperature changes.
If you do not set a temperature range, the baby monitor alerts you when the temperature in your
baby’s room drops below 57°F (14°C) or rises above 86°F (30°C). In this case, the backlight of the
parent unit display goes on and ‘High’ or ‘Low’ appears on the display. To change the default
minimum and maximum temperature, follow the instructions below.
Note: The temperature of the baby’s room is shown on the display of the parent unit when they are
linked.
1 Select ‘Temperature’ with the + and - buttons. (Fig. 32)
2 Press the OK button to conrm.
3 Select ‘Range’ with the + and - buttons. (Fig. 32)
4 Press the OK button to conrm.
5 Set the desired minimum temperature with the + and - buttons.
6 Press the OK button to conrm.
7 Set the desired maximum temperature with the + and - buttons.
8 Press the OK button to conrm.
16
4222.005.0010.1.indd 16 29-03-10 14:38
,The message ‘Saved’ appears on the display.
Note: You can only switch the temperature alert on and off in the menu of the parent unit.
Note: If the temperature alert is activated too often, reduce the set minimum temperature and/or
increase the set maximum temperature (see ‘Setting room temperature range’).
If the temperature alert is switched on, the parent unit beeps if the actual room temperature
exceeds the set maximum temperature or drops below the set minimum temperature. In addition,
the backlight of the parent unit display goes on and ‘High’ or ‘Low’ appears on the display. If no
minimum and maximum temperatures have been set, the temperature alert is given when the room
temperature drops below 57°F (14°C) or rises above 86°F (30°C).
1 Select ‘Temperature’ with the + and - buttons (Fig. 32).
2 Press the OK button to conrm.
3 Select ‘Alert’ with the + and - buttons (Fig. 32).
4 Press the OK button to conrm.
5 If the alert is off, the display shows ‘On?’. Press the OK button to switch on the alert. If the
alert is on, the display shows ‘Off?’. Press the OK button to switch off the alert.
Note: You can only set the temperature scale in the menu of the parent unit.
You can set the temperature scale either to Celsius (C) or Fahrenheit (F).
1 Select ‘Settings’ with the + and - buttons (Fig. 32).
2 Press the OK button to conrm.
3 Select ‘Temp scale’ with the + and - buttons.
4 Press the OK button to conrm.
5 Select ‘Celsius’ or ‘Fahrenheit’ with the + and - buttons.
This function in the menu of the parent unit allows you to reset both the parent unit and the baby
unit to the default settings at the same time. You can use this function if problems occur that you
cannot solve by following the suggestions in chapter ‘Frequently asked questions’.
1 Select ‘Settings’ with the + and - buttons (Fig. 32).
2 Press the OK button to conrm.
3 Select ‘Reset’ with the + and - buttons.
4 Press the OK button to conrm.
,The message ‘Conrm?’ appears on the display of the parent unit.
5 Press the OK button to conrm.
,The parent unit switches off and then switches on again.
,The units have now both been reset to the default factory settings.
Parent unit
- Language: English
- Loudspeaker volume: 1
- Microphone sensitivity: 3
17
4222.005.0010.1.indd 17 29-03-10 14:38
- Sound alert: off
- Temperature alert: off
- ‘Temperature low’ alert: 57°F (14°C)
- ‘Temperature high’ alert: 86°F (30°C)
- Temperature scale: Celsius
- ECO mode: off
Baby unit
- Loudspeaker volume: 3
- Nightlight: off
- Lullaby: off
If the battery pack of the parent unit is sufciently charged, you can take the unit with you inside and
outside the house if you attach the unit to your belt or waistband with the belt clip or if you hang it
around your neck with the neck strap. This allows you to monitor your baby while you are moving
around.
1 Snap the belt clip onto the parent unit (Fig. 35).
1 Pull the belt clip off the parent unit.
1 Insert the end loop of the neck strap through the hole behind the strap post. Thread the
neck strap through the end loop and pull the neck strap tight (Fig. 36).
1 Pass the neck strap though the end loop and pull the end loop out of the hole behind the
strap post.
Do not immerse the parent unit or the baby unit in water and do not clean them under the tap.
Do not use cleaning spray or liquid cleaners.
1 Unplug the baby unit if it is connected to a power outlet and take the parent unit out of the
charger.
2 Clean the parent unit and the baby unit with a damp cloth.
Make sure the parent unit is dry before you put it back into the plugged-in charger.
3 Clean the charger with a dry cloth.
4 Clean the adapters with a dry cloth.
This appliance has no other user-serviceable parts. For assistance call 1-800-54-AVENT (1-800-542-
8368).
- When you are not going to use the baby monitor for some time, remove the non-rechargeable
batteries from the baby unit and the rechargeable battery pack from the parent unit. Store the
18
4222.005.0010.1.indd 18 29-03-10 14:38
parent unit, the baby unit, the charger of the parent unit and the adapters in a cool and dry
place.
- Do not wrap cords around the monitor when storing. Store cords in a safe location where
they will not be cut or damaged.
Only replace the non-rechargeable batteries of the baby unit with four non-rechargeable 1.5V R6
AA batteries.
Note: We recommend you to use Philips non-rechargeable batteries or an equivalent type.
Only replace the adapter of the baby unit with an adapter of the original type. For assistance visit
our website www.philips.com/AVENT or call 1-800-54-AVENT (1-800-542-8368).
Only replace the SCD525 NiMh rechargeable battery pack of the parent unit with a rechargeable
battery pack of the original type. For assistance visit our website www.philips.com/AVENT or call
1-800-54-AVENT (1-800-542-8368).
Only replace the adapter of the parent unit charger with an adapter of the original type. For
assistance visit our website www.philips.com/AVENT or call 1-800-54-AVENT (1-800-542-8368)..
For assistance visit our website www.philips.com/AVENT or call 1-800-54-AVENT (1-800-542-
8368).
- Dispose of batteries properly. Do not incinerate. Batteries may explode if overheated. Do not
wrap in metal or aluminum foil. Wrap in newspaper before discarding (Fig. 37).
- It is suggested that you contact your local town or city to determine proper battery redemption
site(s) in your area.
Philips Electronics North America Corporation (USA) and Philips Electronics Ltd (CANADA)
warrant each new Philips AVENT product, model SCD525/00, against defects in materials or
workmanship for a period of two years from the date of purchase, and agree to repair or replace
any defective product without charge. IMPORTANT: This warranty does not cover damage resulting
from accident, misuse or abuse, lack of reasonable care, or the afxing of any attachment not
provided with the product. NO RESPONSIBILITY IS ASSUMED FOR ANY SPECIAL, INCIDENTAL
OR CONSEQUENTIAL DAMAGES. In order to obtain warranty service, simply call toll-free
1-800-54-AVENT.
19
4222.005.0010.1.indd 19 29-03-10 14:38
This chapter lists the questions most frequently asked about the appliance. If you cannot nd the
answer to your question, visit our website www.philips.com/AVENT or call 1-800-54-AVENT
(1-800-542-8368).
Question Answer
What is ECO mode?
How does this mode
help the environment?
The ECO mode has been developed to enable you to reduce your
energy consumption. Monitoring your baby from a small distance
requires less power than monitoring your baby from a large distance.
When you monitor your baby from a small distance, you can activate
the ECO mode. By switching on the ECO mode, your baby monitor
uses less energy and is therefore more enviornment-friendly.
Why don’t both the
power-on light of the
baby unit and the LINK
light of the parent unit
come on when I press
the on/off buttons of
the units?
Perhaps the rechargeable battery pack of the parent unit is empty and
the parent unit is not in the plugged-in charger. Insert the small
appliance plug into the charger, put the adapter of the charger in a wall
socket and place the parent unit in the charger. Then press the on/off
button to establish connection with the baby unit.
Perhaps the non-rechargeable batteries of the baby unit are empty and
the baby unit is not connected to a power outlet. Replace the
non-rechargeable batteries or connect the baby unit to a power outlet.
Then press the on/off button to establish connection with the parent
unit.
The baby unit and the parent unit may be out of range of each other.
Move the parent unit closer to the baby unit, but not closer than 3
feet/1 meter.
If the LINK light on the parent unit still does not start to ash, use the
reset function to reset the units to their default settings.
Why does the LINK
light on the parent unit
light up red continuously
and why is the message
‘Searching’ shown on
the display?
The baby unit and the parent unit are out of range of each other. Move
the parent unit closer to the baby unit.
The baby unit may be switched off. Switch on the baby unit.
The ECO mode is switched on, but the operating range is too large.
Move the parent unit closer to the baby unit or switch off the ECO
mode.
Why does the battery
light on the baby unit
ash red?
The non-rechargeable batteries of the baby unit are running low.
Replace the non-rechargeable batteries or connect the baby unit to a
power outlet (see chapter ‘Preparing for use’).
Why does the parent
unit beep? If the parent unit beeps while the LINK light lights up red continuously
and the message ‘Searching’ is shown on the display, the connection
with the baby unit is lost. Move the parent unit closer to the baby unit.
20
4222.005.0010.1.indd 20 29-03-10 14:38
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
Philips AVENT AVENT SCD525 Manuel utilisateur
- Catégorie
- Babyphones
- Taper
- Manuel utilisateur
