PICO PocketCinema A100W Manuel utilisateur

User’s Manual

Page 1

EN

Welcome

Thank you very much for purchasing this product. Before you start, you are

recommended to read this manual step by step to obtain the best results with your

new Pico projector. We wish you enjoy it.

About the product

This is the latest generation of Pico projector with DLP technology inside. Known for

great cinema projectors, the DLP technology provides rich colors and enhances the

contrast of the image. Integrated with WLAN, the Pico projector provides cable-free

connection from your notebook, tablet, or smartphone to the Pico projector by

streaming pictures, videos, websites, and documents wirelessly and projecting the

images up to 120’’ (300 cm) in size. With its powerful wireless functionality, and

versatile connection options including HDMI, MHL, Audio -Out, and USB, this Pico

projector is the best solution for mobile use in business and entertainment.

Safety Notice

1. Keep the device and packaging materials out of the reach of infants and children.

2. Avoid subjecting the power adapter and other contacts to dripping or splashing

water and dry your hands before you use it. Do not place objects filled with liquids

such as vases, etc. on or near the device.

3. Make sure that the used power outlet is always readily available and never hidden.

In case of emergency, use the power adapter to separate the device from the power

network.

4. Keep your device away from all flames such as candles and do not set them up in

the vicinity of the device.

5. Keep the unit at least 10 cm away from other objects. Make sure the ventilation is

not covered by newspapers, tablecloths, curtains, etc.

6. For your own safety, do not use the projector during thunderstorms or lightning.

7. Relative Humidity is 20% ~ 80%, non-condensing.

8. The battery is integrated with the device. Do not dissemble and modify. The battery

should be replaced by an authorized service center only.

9. Ensure that the ambient room temperature is within 5 ~ 35°C.

10. Wait before using if the device has been moved from a cold location into a warm one.

Any condensation that has formed may in certain circumstances destroy the device.

As soon as the device has reached room temperature it can be used without risk.

11. Handle the product with care. Avoid contact with sharp objects. Keep device away

from metallic objects.

12. Place the projector on a flat surface. Any collision or falling to the ground is likely to

damage the product.

User’s Manual

Page 2

EN

13. Do not drop or disassemble the product otherwise the warranty voids. Opening or

removing covers may expose you to dangerous voltage or other hazards. Refer all

servicing to an authorized service center.

14. Use only the accessories supplied by the manufacturer.

15. Both product and user’s manual are subject to further improvement or supplement

without further notice.

Care and Safety Information for Pico Projectors

1. Avoid facing directly into the projector’s lens.

2. During the operation, this product may heat

lightly, which is normal.

3. The device should not be used in a very

dusty environment. Dust particles and other

foreign objects may damage the unit.

4. Do not expose the device to extreme

vibrations. It may damage the internal

components.

5. Use the enclosed power adapter (see technical data):

Check whether the mains voltage of the power supply matches the mains voltage

available at the setup location. This equipment complies with the voltage type

specified on the unit.

Notice for Long-time Projection

The built-in battery supports approximately 120 mins of projection. For long time

projection, you are recommended to use AC adapter.

When the battery is too weak to stay in operation, the low battery capacity icon ( )

will flash. You need to charge the product while the icon showed.

It’s normal that the projector will feel warm with continuous use due to its high

performance. If the projector runs for a long time and over-heated, the

High-Temperature icon ( ) will appear on the screen. The system will automatically

enter the standby mode.

Avoid Hearing Damage:

Listening at high volume for a

long period of time could cause

damage to your ears.

User’s Manual

Page 3

EN

FCC Compliance Statement:

This device complies with Part 15 of the FCC Rules. Operation is

subjected to the following two conditions: (1) this device may not cause

harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with limits for a Class B digital device,

pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection

against harmful interference in residential installations. This equipment generates, uses, and

can radiate radio frequency energy, and if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause interference to radio or television equipment reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Move the equipment away from the receiver.

-Plug the equipment into an outlet on a circuit different from that to which the receiver is

connected.

-Consult the dealer or an experienced radio/television technician for additional suggestions.

For product available in the USA/Canada market, only channel 1~11 can be operated. Selection

of other channels is not possible.

This device and it's antennas(s) must not be co-located or operating in conjunction with any

other antenna or transmitter except in accordance with FCC multi-transmitter product

procedures.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance 20cm

between the radiator & your body.

All cables used to connect peripherals must be shielded and grounded. Operation with cables

connected to peripherals that are not shielded and grounded may result in interference to radio

and television reception.

You are cautioned that any change or modifications to the equipment not expressly approved by

the party responsible for compliance could void your authority to operate such equipment.

If the time arises to throw away your

product, please recycle all the components

possible. Batteries and rechargeable

batteries are not to be disposed in your

domestic waste! Please recycle them at

your local recycling point.

Together we can help to protect the

environment.

User’s Manual

Page 4

EN

Content

About the Product, Safety Notice 1

Package Content 5

Knowing Your LED Projector 6

Getting Started 7

Charging the product 7

LED Indicators 7

Power On / Off the Projector 7

Adjusting the Focus according to distance 8

Adjusting the brightness of your projector 8

Projecting from External Video Input Source 9

HDMI Input 9

Projecting from Smartphones or Tablets 9

Displaying the image on an external LCD monitor 10

HDMI Output 10

Charging the external mobile devices 10

Overview of the Main Screen 11

Install the wireless application software on your

computer

12

Peer-to-Peer wireless projection from computer 14

Install the wireless application software on Apple or

Android devices

18

Installing EZCast for Android device 18

Installing EZCast for Apple devices 19

User’s Manual

Page 5

EN

Peer-to-Peer wireless projection from Apple or

Android devices

20

Adding Content to EZCast using iTunes® (For

Apple Device)

22

Sketch the image from EZCast 23

Wireless mirror projection with your Miracast

enabled devices. 24

DLNA feature for EZCast App 25

Connect the projector to available Wi-Fi network

(Home Network Mode) for Internet access

26

Trouble Shooting 28

Support Input Timings 28

Specifications 29

Package Content

Please check if the following items are located in your packaging:

xPico Projector

xPower Adapter

xExchangeable Power Plug

xMHL Cable (HDMI Type A to USB Type D)

xHDMI Cable

xCarry Bag

xUser’s Manual

User’s Manual

Page 6

EN

Knowing your LED Projector

Brightness Adjustment

Volume Up

Volume Down

Projection Lens

Ventilation holes

LED Indicator

HDMI / MHL Input

Connector

HDMI Output

Connector

Power

USB Connector

DC IN

Reset Hole

Audio Output Jack

Focus Ring

Speaker

Tripod Socket

Fan

User’s Manual

Page 7

EN

Getting Started

Charging the product

The projector is built in a Li-Polymer battery

for mobile use. Please charge the projector

for 8 hours prior to its first use. Repeat

charging will take around 4 hours.

The battery will be charged only when the projector is not in use (Power off). Connect

one end of the supplied power adapter to DC IN jack and the other end to a power

outlet to start charging.

Exchange the plug (EU, US and etc.) of AC adapter that accommodates the type of

power outlet in your country if it’s different.

Charging LED Indicator

During charging, the LED indicator lights will flash as marquee. When the battery is

fully charged, the LED indicator lights turns to solid blue.

LED indicators

LED Status Indication

3 blue LEDs stay on Power capacity is between 80% to 100%

2 blue LEDs stay on Power capacity is between 45% to 80%

1 blue LED stays on Power capacity is between 10% to 45%

1 blue LED blinks Power capacity is below 10%

LED Marquee Projector is being charged

3 blue LEDs blink Charging the external mobile device

Power On / Off the Projector

Push the Power button for 2 seconds to turn on the projector.

To power off the projector, push the Power button again for 2 seconds.

Standby mode: Push the Power button for 1 second to turn on/ off the projector lamp

for a short break to save the battery and system reboot time. (The LEDs are still on

when the projector is in standby mode.)

User’s Manual

Page 8

EN

Adjusting the Focus according to distance

Place the projector on a flat surface and

toward a wall or a projection screen. The

projectional distance and projectional size are:

Distance: 50 cm ~ 425 cm (20 ” ~ 167 ”)

Image size: 36 cm ~ 305 cm (14 ” ~ 120 ”)

Adjust the focus by turning the focus ring to get a sharp and clear picture.

Note: Use a tripod (not included) to increase the height of the projectional image

when necessary. The tripod socket is located under the projector.

Adjusting the brightness of your projector

There is a brightness adjustment button on the right side of the projector. It allows you

to change the brightness according to the environment and the power consumption.

1) Enhanced: Select this mode when external power supply is available to

maximize the brightness performance.

2) Standard: The default mode for optimizing the projection performance and

battery capacity.

3) Eco: This mode is recommended when the projector is operated under battery

mode to save power.

Note: The projector is automatically switched to Enhanced mode when It’s

powered by the power adapter.

Mode Brightness Battery Life

(HDMI mode)

Enhanced Up to 120 lumens 80 mins

Normal Up to 85 lumens 100 mins

Eco Up to 60 lumens 120 mins

User’s Manual

Page 9

EN

Projecting from External Video Input Source

The projector has built-in HDMI interface on the rear side. You can connect your

external video Input source to the projector or output the projector’s screen to a LCD

monitor or HDTV by using the appropriate cable.

HDMI Input

Use the HDMI cable to connect the HDMI port on

the rear panel of the projector to the external

HDMI signal source. After connected, the screen

switches to HDMI source automatically.

Projecting from Smartphones or Tablets

1. Connect your smartphone supporteing MHL (Mobile High-Definition Link) for

projection.

Connect your smartphone (e.G.Samsung Galaxy

S2, Note; new HTC one, one X; or Sony Xperia

Z2, Z Ultra, Z) with the projector via the bundled

MHL (Type A to USB Type D type HDMI) cable.

Note: 1. For Samsung Galaxy S5, S4, S3, Note 4, Note 3, Note 2, Samsung 5

to 11 pin MHL converter (as illustration shows) is needed.

2. It’s normal that the projector is automatically charging the smartphones

or tablets when connected with the MHL cable for projection.

3. Samsung 5 to 11 pin MHL coverter is not included in the package.

2. Connect iPhone 6 plus, 6, 5S, 5, iPad Air2, Air,

iPad mini 3, mini 2, mini and iPod touch 5th

with the projector via Apple Lightning Digital

AV adapter and A-to-A type HDMI cable.

iPhone 4S, 4, New iPad, iPad 2, and iPod

touch (4th) can connect with projector with

Apple 30-pin digital AV adapter and A-to-A type HDMI cable

Note: Apple Lightning Digital AV adapter and 30-pin digital AV adapter are not

included in the package.

User’s Manual

Page 10

EN

Displaying the image on an External LCD

Monitor

The projector has built-in a HDMI output interface on the rear side. If the environment is

not suitable for projection, you can connect the projector to an LCD monitor or HDTV

with HDMI input port by using a HDMI cable.

HDMI Output

Use the HDMI cable to connect the HDMI output

port on the rear panel of the projector to a LCD

monitor or HDTV. After connected, the screen

switches to LCD monitor automatically.

Charging the External Mobile Device

The internal battery of the projector cannot only be used for projection, but also

charge your mobile device.

1. Connect your mobile device to the projector via the USB

cable with the end of Type A connector plugged into the

USB port on the rear side of projector.

2. The device will be charged automatically when

connected with the projector.

3. Some MHL device does not follow the standard

power design, so that its battery can not be

charged by the projector (e.g. Samsung Galaxy

Nexus, HTC M8)

Note: 1. The projector provides max 5V / 1A output power for charging the mobile

devices.

2. USB cable is not included in the package.

User’s Manual

Page 11

EN

Overview of the Main Screen

Power on the projector, the following screen appears after the projector boots up.

For first-time use, please install the wireless application software first, on your PC

or smartphone.

Computer users (Windows and MAC):

Please scan the QR code or enter the IP address into the address bar of your

PC browser to download the driver.

http://www.iezvu.com/download

Android users:

Please scan QR code to download EZCast APP from Google Play™or

search for EZcast in Play Store.

iPad and iPhone users:

Please scan QR code to download EZCast APP from App Store or search

for EZcast in App Store..

User’s Manual

Page 12

EN

Install the wireless application software on your

computer

1. Connect the computer to an available network for Internet access.

2. Open the Internet browser on your computer then enter the IP Address

http://www.iezvu.com/download in the browser’s address bar.

3. Select the driver for Windows or Mac OS depending on your operating system

and then click <Download> to enter the download page.

User’s Manual

Page 13

EN

4. If you are the first time downloading, please enter the “Register” page to fill out

your E-mail address and the SSID named on top side of the projector’s main

screen (see screenshot Overview of the Main Screen).

5. Click <Download> to start the installation and follow on-Screen

instructions to complete the setup and reboot the computer. When the

installation is completed, an icon, labeled EZCast will appear

on your computer desktop.

User’s Manual

Page 14

EN

Peer-to-Peer (direct) wireless projection from

computer

Peer-to-peer wireless connection from your computer with the projector allows you

quickly start the presentation or watch a movie wirelessly.

1. Power on the engine and enter to main screen of the projector.

2. Make a note of the Password in 8 digits XXXXXXXX on the top side of main

screen. You will need the information to log in later.

3. Connect your computer to the projector Wireless network by selecting SSID:

Projector-XXXXXXXX on the network list, enter the Password (see Step 2)

and click <OK> to confirm.

4. Double-click EZCast icon on your computer desktop to start the

application.

5. After successfully logged in, the wireless projection between the computer

and the projector has been established.

6. Select the projection output method from Off (default) to Mirror or Extension

to start the wireless projection

User’s Manual

Page 15

EN

Advanced functions of EZCast app

Item Descriptions

This item allows users to select the projection output

methods.

Off: Click to stop the wireless projection

Mirror: Displays the same picture on the screen of

the computer

Extension: Extend the screen from computer to the

projector.

Click to select the ideal mode for watching movie or

photo slideshow.

High Quality: ideal for photo slideshow

Low Quality: ideal for watching movie

Stream the Audio to the projector’s speaker.

Note: If you don’t like to hear the sound from the

computer at the same time, disable the speaker on the

computer by choosing ‘mute’.

Click to enhance 3rd party software compatibility. (The

performance (frame rate) of wireless streaming may be

reduced.)

User’s Manual

Page 16

EN

Search music files on the computer and stream to the

projector’s speaker.

Click to select the ideal mode for watching movie or

photo slideshow

Video: ideal for watching movie

Graphic: ideal for photo slideshow

This item allows users to on-line upgrade the lastest

version for EZCast app.

Projecting Web pages. (Home Network mode only)

* Please see page 26 to enable Home Network mode.

Click to flinging on-line video to the projector. (Home

Network mode only)

* Please see page 26 to enable Home Network mode.

EZCast acts as a DLNA DMR (Digital Media Renderer)

for DLNA application.

Click to enter the EZCast settings menu.

* Please switch the output method to “Off” before select

this item.

User’s Manual

Page 17

EN

EZCast Settings menu

Item Descriptions

This item allows users to change the password of the

proejctors (EZCast SSID).

This item allows users to connect the proecjtor to a

Wi-Fi network (home network).

This item allows users to select the displayed system

language.

This item allows users to select the default running

mode (EZCast or EZMirror) when power on the

projector.

This item allows users to select the connection path via

direct link or a router.

This item allows users to online upgrade the lastest

firmware version for the projector. (Home Network

mode only)

* Please see page 26 to enable Home Network mode

User’s Manual

Page 18

EN

Install the wireless application software on Apple

or Android devices

EZCast for Android smartphone and Apple iDevice

EZCast is an application that runs on your Android smartphone or Apple devices

and transmits still images or presentations to the projector. The EZCast is only

used for a wireless connection. If you are connecting your phone to the projector

using a cable, you can use the built-in video App of your phone.

Installing EZCast from Google Play™ (For Android

device)

1. Connect to the Internet and open the Google Play™ or Google Play™ web

page. ( Google Play™ is a trademark of Google Inc.)

2. In the search bar, type EZCast. (Or scan the QR code directly from the Main

Screen.)

3. Click the <INSTALL> button to download and install the free EZCast app.

4. Follow the instructions to finish the installation.

User’s Manual

Page 19

EN

Installing EZCast from Apple App Store (For Apple

devices)

1. Connect your iPhone to the Internet and Launch the App Store.

2. In the search bar, type EZCast. (Or scan the QR code directly from the Main

Screen.)

3. Click the <INSTALL> button to download and install the free EZCast app.

4. Follow the instructions to finish the installation.

User’s Manual

Page 20

EN

Peer-to-Peer (direct) wireless projection from

Apple or Android devices

Before you can transmit images to the projector using EZ Cast, you must connect

your Android smartphone or Apple device to the projector (peer-to-peer).

Opening EZCast and Logging into the projector

1. Open the EZCast application and click the first icon (search). EZCast will

search for compatible devices.

2.Choose WiFi Projector (Name as SSID shown on the top of projection screen)

and enter the Login password shown on the projector screen as well. After

connecting to the projector a blue connection icon will be shown on projection

screen in right top corner

3. Select the type of files on your smartphone for projection.

La page charge ...

PICO PocketCinema A100W Manuel utilisateur

Ce manuel convient également à

PICO PocketCinema A100W Manuel utilisateur

dans d''autres langues

Autres documents