Breville CJE830 Manuel utilisateur

Catégorie
Fabricants de jus
Taper
Manuel utilisateur
EN INSTRUCTION BOOK FR-CA MANUEL D'INSTRUCTIONS ES-MX MANUAL DE INSTRUCCIONES
the Juice Fountain® Cold XL Pro
Instruction Book – CJE830
2
IMPORTANT
SAFEGUARDS
READ ALL INSTRUCTIONS
BEFORE USE AND SAVE
FOR FUTURE REFERENCE
Remove and safely discard
any packaging material or
stickers before using the
juicer for the first time.
To eliminate a choking hazard
remove and safely discard the
protective cover fitted to the
power plug of this appliance.
Fully unwind the power cord
before use.
Do not place the juicer near
the edge of a countertop or
table. Ensure the surface is
level, clean and free of water
and other substances.
Always ensure the juicer is
properly assembled before use.
Always make sure the juicer
filter basket, collector and top
cover are fitted and clamped
securely in place before the
motor is turned on.
Do not unfasten clamps while
the juicer is in operation.
Do not use the appliance
if the rotating filter basket
(sieve) is damaged.
Contents
BREVILLE |
COMMERCIAL
RECOMMENDS
SAFETY FIRST
At Breville | Commercial
we are very safety conscious.
We design and manufacture
consumer products with
the safety of you, our valued
customer, foremost in mind.
In addition we ask that you
exercise a degree of care when
using any electrical appliance
and adhere to the following
precautions.
2 Breville | Commercial
Recommends Safety First
6 Components
7 Assembly
8 Functions
10 Care & Cleaning
11 Troubleshooting
13 Tips
3
Do not operate without the
pulp container in place.
Before juicing any food, fruits
or vegetables, inspect and
clean to ensure the following;
all rinds and hard skin
have been removed,
there are no pits, stones
or heavy seeds,
packing or bundling ties and
metal wire have been removed.
Not following the above
instructions can lead to
unsafe operation and may
cause serious injury.
Never plug in or switch
ON the juicer with food
present in the feed chute.
Allow the motor to reach
proper speed before pushing
food through the feed chute.
Do not put your fingers or
other objects into the juicer
opening while it is plugged in
or in operation. If food becomes
lodged in opening, only use
food pusher or another piece
of fruit or vegetable to push
it down. When this method
is not possible turn the unit
OFF and disassemble juicer to
remove the remaining food.
Do not leave the juicer
unattended when in use.
Avoid contact with moving parts.
Be sure to turn the switch to
the OFF position after each
use of your juicer. Make sure
the motor stops completely
before disassembling.
To disconnect, turn the
control OFF, then remove
plug from wall outlet.
Properly clean the unit and filter
basket after each use to avoid
leaks or overflow and to ensure
the unit operates as intended.
Be careful when handling
the filter basket as the small
cutting blades at the base of
the filter basket are very sharp.
Mishandling may cause injury.
Turn the appliance OFF,
then unplug from the outlet
when not in use, before
assembling or disassembling
parts and before cleaning.
To unplug, grasp the plug and
pull from the outlet. Never
pull from the power cord.
This appliance is not intended
for use by children or by persons
with reduced physical, sensory,
or mental capabilities, or lack
of experience and knowledge.
Close supervision is necessary
when any appliance is
used near children.
Children should be supervised
to ensure that they do not
play with the appliance.
4
Do not use in any type of
moving vehicles. Do not use
the appliance outdoors, or for
anything other than its intended
use. Misuse can cause injury.
The use of attachments not
recommended or sold by the
manufacturer may cause fire,
electric shock or injury.
To protect against risk of
electric shock, do not immerse
the cord, plug or motor base
in water (or other liquids).
A representative example of
the heaviest loading suitable for
use with this juicer is equivalent
to 11 pounds (5kg) of carrots,
juiced continuously with a
push force of 11 pounds (5kg).
NOTE
If the motor stalls or strains under
load, do not operate continuously
for more than 10 seconds
at a time.
SAVE THESE INSTRUCTIONS
NOTE
If the juicer stops due to
improper operation or if there
is excessive noise, shaking, or
vibration, turn the unit OFF and
allow the filter to stop spinning
completely. Unplug the unit from
the power outlet, disassemble
and clean all components before
properly reassembling.
5
IMPORTANT
SAFEGUARDS
FOR ALL
ELECTRICAL
APPLIANCES
Do not let the cord hang over
the edge of a table, counter, or
let touch a hot surface such
as a stove. Do not place on
or near a hot gas or electric
burner or in a heated oven.
It is recommended to regularly
inspect the appliance and
power cord. Do not use the
appliance if there is damage to
the power cord or plug, or after
the appliance malfunctions
or has been dropped or
damaged in any way. If this
occurs, immediately stop use
and call Breville | Commercial
Consumer Support.
If the above issues persist,
stop use of the juicer and
contact Breville | Commercial
Consumer Support.
BREVILLE ASSIST® PLUG
Your Breville | Commercial
appliance comes with a unique
Assist® Plug, conveniently
designed with a finger hole to ease
removal from the power outlet.
This appliance has a polarized
plug (one blade is wider than
the other). To reduce the risk of
electric shock, this plug will fit in
a polarized outlet only one way.
If the plug does not fit fully in the
outlet, reverse the plug. If it still
does not fit, contact a qualified
electrician. Do not modify the plug
in any way.
SHORT CORD
INSTRUCTIONS
Your Breville | Commercial
appliance is fitted with a short
power supply cord to reduce
personal injury or property damage
resulting from pulling, tripping or
becoming entangled with a longer
cord. If an extension cord is used,
(1) the marked electrical rating
of the cord set or extension cord
should be at least as great as the
electrical rating of the appliance,
(2) the cord should be arranged
so that it will not drape over the
countertop or table-top where it
can be pulled on by children or
tripped over unintentionally and (3)
the extension cord must include a
3-prong grounding plug.
6
Rating Information
Components
A
E
F
I
H
G
D
B
C
A. Food pusher
(not dishwasher safe)
B. Interlocking safety arm
Stops juicer operating without cover
locked into place.
C. Juicer cover
(dishwasher safe)
D. Stainless steel filter basket
(dishwasher safe)
E. Pulp container
(dishwasher safe)
F. Filter bowl surround
(dishwasher safe)
G. Variable speed control and off dial
H. Overload protection indicator light
I. 70 fl. oz. (2 liter) juice jug and sealing lid
with built in froth separator
(dishwasher safe).
J. Juicing Nozzle
(dishwasher safe)
Can be placed over spout to juice directly
into a cup.
J
D
120 V ~60 Hz 1200 W
7
Assembly
BEFORE FIRST USE
Before using your juicer for the first time,
remove and safely discard any packaging
materials and promotional stickers
and labels.
Ensure the power cord is unplugged.
Wash the filter bowl surround, filter basket,
juicer cover, food pusher, pulp container and
juice jug and lid in warm, soapy water with a
soft cloth. Rinse and dry thoroughly.
1. Place motor base on a flat, dry surface
such as a countertop. Ensure that the
juicer is switched OFF at the dial,
and the power cord is unplugged.
2. Place filter bowl surround on top of the
motor base.
3. Align the arrows at the base of the stainless
steel filter basket with the arrows on the
motor drive coupling and push down until it
clicks into place to create a secure fit with
the motor base.
4. Place the juicer cover over the filter bowl
surround, positioning the lower part of
the feed chute over the stainless steel
filter basket.
5. Raise the safety locking arm up and lock
into the two grooves on either side of the
juicer cover.
6. The safety locking arm should now be in a
vertical position and locked into place on
top of the juicer cover.
8
7. Slide the food pusher down the food chute
by aligning the groove in the food pusher,
with the small protrusion on the inside of
the top of the feed tube.
8. Place the pulp container into position by
tilting and lifting the motor base slightly.
Insert the pulp container under the juicer
cover on the back ensuring it is supported
by the juicer cover and motor base.
9. Fit the lid to the juice jug and position jug
under juice spout.
JUICE JUG
Juice can be preserved in the juice jug for up to
3 days by following these steps.
1. Lift the lid off the jug and rotate 180°
2. Press down firmly to replace the lid
3. Store juice in the fridge
NOTE
Storage time depends on the ingredients being
juiced and the freshness of the fruit prior to
juicing. Juice must be stored in the refrigerator
between 32°F to 39°F.
Functions
1. Wash your selection of fruit and vegetables
to be juiced. Most fruit and vegetables
such as apples, carrots and cucumbers
will not need to be cut or trimmed to size
as these will fit whole into the feed chute.
Ensure vegetables such as beets, carrots
etc. have all soil removed, are washed
well and trimmed of leaves before using.
2. Plug the power cord into a 120V power outlet.
IMPORTANT
Do not load feed chute with produce before the
Juicer has reached the selected speed.
3. Turning the Juicer On
Turn dial to desired speed setting. Turn dial
to medium speed for most juicing needs. For
harder fruits/vegetables and leafy greens
select the “Hard” range. Use the speed
selector when applicable to match the speed
and produce type, for maximum yield.
4. With the motor running, place food into
the feed chute and use the food pusher
to gently guide food down. To extract
the maximum amount of juice, always
push the food pusher down slowly.
5. Full Juice Jug
You can keep juicing until the juice jug
is filled to max. level.
6. Continuous Juicing
Having just filled and removed a juice jug
with fresh juice, you can place an empty
juice jug back onto the nozzle and continue
juicing without disassembly. When the pulp
container is near full with pulp, turn the dial
to “Off”, remove the pulp container only
and empty contents. Replace the empty
pulp container and turn dial to desired
speed selection to continue juicing.
Food
pusher
groove
Small
protrusion
inside
feed tube
9
SPEED SELECTOR GUIDE
FOOD TYPE SPEED
APPLE Preset
BABY SPINACH Hard
BEET Hard
BELL PEPPER Hard
BLUEBERRY Preset
BROCCOLI Hard
CABBAGE Hard
CARROT Preset
CELERY Preset
CITRUS FRUIT (peeled) Preset
CUCUMBER (green tip removed) Preset
GINGER Preset
GRAPE (seedless) Medium
HONEYDEW MELON (peeled) Preset
KALE Hard
KIWI (peeled) Medium
MANGO (peeled, pit removed) Hard
MINT Hard
PEACH (pit removed) Hard
PEAR Medium
PINEAPPLE (peeled) Preset
RHUBARB Hard
SQUASH Hard
STRAWBERRY Preset
TOMATO Medium
WATERMELON (peeled) Preset
ZUCCHINI Medium
NOTE
Do not allow the pulp container to overfill as
this may affect the operation of the appliance.
The juicer is fitted with a safety device
which safeguards against overheating
with excessive loads. If overheating occurs,
the juicer will automatically activate the
overload protection device and the unit
will switch itself off. When the overload
protection is activated, unplug the juicer
from the power outlet for at least 30 minutes
to allow the unit to cool. Then plug juicer
into the power outlet and use as normal.
WARNING
Never use fingers, hands or utensils to push
food down the feed chute or to clear the feed
chute. Always use the food pusher provided.
The stainless steel filter basket contains small
sharp blades to cut and process fruit and
vegetables. Avoid touching the blades when
handling the filter basket.
Caution:
sharp blades
10
Care & Cleaning
Ensure the juicer is turned off by turning the
juicer dial to the OFF position. Then unplug
the power cord.
CLEANING
1. Remove juice jug.
2. Remove pulp container.
3. Disengage locking bar, pull up entire juice
collector assembly and take to sink.
Rinse all parts after use (except the motor base)
under running water to clear away the majority
of juice and pulp. Wash in warm soapy water
with a soft cloth.
To avoid food drying on to the blades, mesh
or transparent parts, rinse and wash as soon
as possible after use.
PULP CONTAINER
To minimize cleaning, you can line the pulp
container with a biodegradable bag to collect
the pulp.
MOTOR BASE
To clean the motor base, wipe with a soft, damp
cloth then dry thoroughly. Wipe any excess
food particles from the power cord.
Do not immerse the motor base in liquids.
CLEANING AGENTS
Do not use abrasive scouring pads or cleaners
on either the motor base or the jug, as they may
scratch the surface. Use only warm soapy water
with a soft cloth.
DISHWASHER
Wash all parts (except the motor base)
in warm soapy water with a soft cloth.
All parts except for the motor base, juicer
cover and food pusher are dishwasher safe.
However washing parts on a regular base in
the dishwasher can shorten the life of them
due to prolonged exposure to harsh detergents,
hot water and pressure.
Cleaning the parts in the dishwasher also may
cause parts to deteriorate so inspect the parts
regularly and stop using the product if any
signs of damage is noticed.
FILTER BASKET
To ensure consistent juicing results, always
clean the filter basket thoroughly immediately
after use.
If pulp is left to dry, it may clog the fine pores
of the filter mesh, which can affect juicing
performance. The filter basket can be soaked in
hot soapy water for 10 minutes, if necessary.
Hold the filter basket under running water and
use cleaning brush (supplied with the juicer)
in a circular motion to clear away pulp from
the inside of the basket, including the blades.
Turn over, use the cleaning brush in a circular
motion to clear away pulp from the outside of
the basket, and repeat if necessary.
After cleaning, hold up towards a light source
to check that the fine mesh pores are not
blocked. If blocked, soak the filter basket in
hot water with 10% lemon juice to loosen, and
brush under running water again.
Do not soak the filter basket in bleach,
harsh chemicals or abrasive cleansers.
Always treat the filter basket with care, as it can
be easily damaged. Do not use if there is any
damage or deformation to the filter mesh.
Filter basket can be washed in the dishwasher
(top shelf).
The center of the filter basket has an array of
small, sharp blades. Do not touch these blades
when handling the filter basket.
STUBBORN FOOD STAINS
Discoloration of the plastic may occur with
strongly colored fruit and vegetables. To help
prevent this, wash parts immediately after use.
If discoloration does occur, the plastic parts
can be soaked in water with 10% lemon juice
or can be cleaned with a non-abrasive cleaner.
11
Troubleshooting
PROBLEM EASY SOLUTION
Juicer will not work
when switched ON The safety locking arm may not be correctly engaged in the vertical
operating position. Check the top cover is properly aligned and the locking
arm is located firmly into the two grooves on either side of the juicer cover.
Motor overload protection may have operated (see below).
Overheating with
excessive loads The juicer is equipped with an internal self-resetting overload to prevent
the motor from damage under heavy or continuous loads. If the motor
suddenly stops working, turn the dial OFF, and unplug the unit from
the power outlet. Allow the juicer to cool for at least 30 minutes before
operating again.
NOTE: The unit MUST be turned off in order for it to cool and be reset.
Despite this overload protector, we suggest juicing in smaller batches,
without excessive pushing force, to avoid overheating and stalling and to
maintain the life of the motor.
Excess pulp building
up in the stainless
steel filter basket
Stop juicing, disassemble to scoop excess pulp off the juicer cover.
Reassemble and continue juicing. Alternating soft and hard ingredients
may help avoid this.
Pulp too wet and reduced
extracted juice The cleaner the filter, the better the juice yield, and dryer the pulp.
Be sure to thoroughly clean the juicer as soon as possible after each use.
Remove the stainless steel filter basket and thoroughly clean mesh walls
with a cleaning brush. Rinse the filter basket under hot water. If the fine
mesh holes are blocked, soak the basket in a solution of hot water with 10%
lemon juice to unblock the holes or wash in the dishwasher (top shelf).
This will remove excess fiber build up which could be inhibiting the flow.
Juice leaks between
the rim of the juicer
and the juicer cover
Try a slower juicing speed and push the food pusher down the feed chute
more slowly.
Juice sprays out
from spout The juice is being extracted too fast; try a slower juicing speed (if possible)
and push the food pusher down the feed chute more slowly.
12
PROBLEM EASY SOLUTION
Motor appears to
stall when overload
protection LED flashes
Wet pulp can build up under the juicer cover and stall the juicer if the juicer
is used excessively without cleaning. If this occurs, disassemble and follow
the cleaning instructions to clean the filter bowl surround, the stainless
steel filter basket and the juicer cover. The juicer can also stall if excessive
force is used to push produce down the feed chute. If this occurs, ensure
that a more gentle pressure is used to push produce down the chute.
The juicer will automatically stop operating if too much food is being
processed at one time. Try processing a smaller amount per batch. To
continue juicing, reset the juicer by turning the juicer OFF and back ON.
Turn on the juicer before putting ingredients in the chute. Pressing
ingredients down before the juicer reaches full speed can cause the motor
to stall or overload. Use gentle to moderate pressure on the pusher. Lower
pressure produces a better juice yield.
Hard fruit and vegetables will put excess strain onto the motor if a low
speed is selected. Refer to the juicing guide to determine the correct speed
for the fruit and vegetables selected for juicing.
Overload protection
LED light flashing
during the use
This indicates the motor speed is slowed down to an inefficient level.
This may be caused by excessive pushing force on the pusher or too much
pulp building up on the lid or in pulp bin. Use moderate pushing force on
the food pusher and regularly clean the lid and pulp bin to ensure the juicer
is operating at optimal speed.
Overload Protection
LED is on This indicates motor overload protection is activated.
To reset the unit, turn the dial OFF, unplug the juicer and let the motor cool
down for 25 to 30 minutes, then plug the juicer back in.
If any of the above issues persist, or if you have questions, stop use of the juicer and contact
Breville | Commercial Consumer Support.
13
Tips
PREPARATION OF FRUITS AND
VEGETABLES
Fruits with hard or inedible skins should be
peeled before juicing, including mangoes,
guavas, melons, etc.
Some vegetables, such as cucumbers can be
processed unpeeled depending on the softness
of the skin and whether you like the taste of the
skin in your juice.
Fruits with hard seeds or pits must be pitted
before juicing, including nectarines, peaches,
mangoes, plums, cherries, as the skin and pith
can make the juice bitter.
Citrus fruits with thick pith or skin should
be peeled before juicing, including oranges,
lemons, mandarins, etc.
Trim leaves and wash vegetables to remove
earth/soil, including carrots, beet, spinach, etc.
Trim, hull and remove stalks before juicing,
including strawberries, apples, pears, etc.
A small amount of lemon juice can be added
to apple juice to reduce browning.
THE RIGHT TECHNIQUE
When juicing a variety of ingredients with
varying textures, start with the softer textured
ingredients on the SOFT speed and then
gradually change to the HARD speed for the
harder textured ingredients.
If you are juicing herbs, sprouts or other leafy
green vegetables, either wrap them together
to form a bundle or alternate with more solid
ingredients for the best extraction.
Fruits and vegetables produce different
amounts of liquids, and can vary between
batches or at different times of year.
Juice recipes are not exact, so therefore the
precise quantities of any juice are not crucial
to the success of a particular mixture.
To extract the maximum amount of juice
always push the food pusher down slowly.
Allow the motor to reach full speed before
putting ingredients in the chute.
Pressing ingredients down before the juicer
reaches full speed can cause the motor to stall
or overload. Use gentle to moderate pressure
on the food pusher. Lower pressure produces
a better juice yield.
USING THE PULP
The remaining pulp left after juicing fruit and
vegetables is mostly fiber and cellulose which,
like the nutrients in juice, are necessary for the
daily diet and can be used in many ways.
Vegetable pulp can be used to add bulk to
rissole mixtures, thicken casseroles or soups.
Fruit pulp can be placed in a heat proof bowl,
topped with meringue, and baked in the oven
for a simple dessert.
When using the pulp, there may be some
pieces of fruit or vegetables remaining.
These should be removed before using the
pulp in any recipes.
Apart from consumption use, pulp can also
be used to create compost for the garden.
14
Fruit and Vegetables Best season
to buy
Storage Nutritional value Kilojoule/
calorie count
Apple Fall/ Winter Vented plastic bags
in refrigerator
Vitamin C,
dietary fiber
5.9oz (166g)
Apple
= 338kj (80 cals)
Apricot Summer Unwrapped
in crisper of
refrigerator
Potassium,
dietary fiber
1.9oz (55g )
Apricot
= 80kj (19 cals)
Beet Winter Cut off tops,
then refrigerate
unwrapped
Vitamin C, folate,
dietary fiber,
potassium
5.6oz (160g) Beet
= 332kj (79cals)
Blueberry Summer Cover in the
refrigerator
Vitamin C 3.5 oz (100g)
Blueberries
= 220kj (52 cals)
Broccoli Fall/ Winter Plastic bag in
refrigerator
Vitamin C, B2, B5,
B6, E, folate,
dietary fiber
3.5oz (100g)
Broccoli
= 131kjs (31 cals)
Cabbage Winter Wrapped, trimmed
in the refrigerator
Vitamin C, B6,
folate, dietary fiber,
potassium
3.5oz (100g)
Cabbage
= 93kj (22 cals)
Carrot Winter Uncovered in
refrigerator
Vitamin C, B6, beta-
carotene, potassium
3.5oz (100g)
Carrots
= 140kj (33 cals)
Cauliflower Fall/ Winter Remover outer
leaves, store in
plastic bag in
refrigerator
Vitamin C, B5,
B6, folate and
potassium
3.5oz (100g)
Cauliflower
= 103kj (24.5 cals)
Celery Fall/ Winter Refrigerate in
plastic bag
Vitamin C,
potassium
3.5oz (100g) stick
= 64kjs (15 cals)
Cucumber Summer Crisper in
refrigerator
Vitamin C 3.5oz (100g)
Cucumber = 50kj
(12 cals)
Fennel Fall to Spring Refrigerate Vitamin C, folate,
dietary fiber
3.5oz (100g)
Fennel = 80kj
(19 cals)
Grapefruit All year round Cool, dry place for
1 week, transfer to
refrigerator to keep
longer
Vitamin C,
bioflavonoids,
lycopene,
dietary fiber
3.5oz (100g)
Grapefruit = 140kj
(33 cals)
Grape
(Seedless)
Summer Plastic bag in
refrigerator
Vitamin C, B6,
potassium
3.5oz (100g)
Grapes
= 250-350kj
(60-83 cals)
15
Fruit and Vegetables Best season
to buy
Storage Nutritional value Kilojoule/
calorie count
Kale Fall/ Winter Crisper in
refrigerator
Vitamin C, K, beta-
carotene, folate,
dietary fiber
3.5oz (100g) Kale
= 206kj (49 cals)
Kiwi Fruit Winter/ Spring Crisper in
refrigerator
Vitamin C,
potassium
3.5oz (100g)
Kiwi Fruit = 219kj
(52 cals)
Mango Summer Covered in
refrigerator
Vitamin A, C, B1, B6,
potassium
7.3oz (207g)
Mango
= 476kj (113 cals)
Melon including
Watermelon
Summer/ Fall Crisper in
refrigerator
Vitamin C, folate,
beta-carotene,
dietary fiber
7oz (200g) Melon
= 210kj (50 cals)
Nectarine Summer Crisper in
refrigerator
Vitamin C, B3,
potassium,
dietary fiber
5.3oz (151g)
Nectarines
= 277kj (66 cals)
Orange Winter/ Fall/
Spring
Cool, dry place for
1 week, transfer to
refrigerator to keep
longer
Vitamin C 4.6oz (131g)
Orange
= 229kj (54 cals)
Peach Summer Ripen at room
temperature then
refrigerate
Vitamin C, beta-
carotene, potassium,
dietary fiber
3.5oz (100g)
Peaches
= 175kj (42 cals)
Pear Fall/ Winter Ripen at room
temperature then
refrigerate
Vitamin C, E,
dietary fiber
5.7oz (161g Pear)
= 391kj (93 cals)
Pineapple Spring/ Summer Store in a cool
place
Vitamin C, E,
dietary fiber
3.5oz (100g)
Pineapple
= 180kj (43 cals)
Spinach All year round Refrigerate Vitamin C, B6,
E, beta-carotene,
folate, magnesium,
potassium,
dietary fiber
3.5oz (100g)
Spinach
= 65kj (15 cals)
Tomato Late Winter to
early Summer
Ripen at room
temperature then
refrigerate
Vitamin C, E,
lycopene, folate,
dietary fiber
3.5oz (100g)
Tomatoes
= 65-75kj
(15-17 cals)
16
Notes
the Juice Fountain® Cold XL Pro
Manuel d’instructions – CJE830
FR-CA MANUEL D'INSTRUCTIONS
2
IMPORTANTES
MESURES DE
CURITÉ
LISEZ TOUTES LES
INSTRUCTIONS AVANT
USAGE ET CONSERVEZ-
LES À TITRE DE
RÉFÉRENCE.
Retirez et jetez en lieu sûr tout
matériel d’emballage ou collants
avant d’utiliser votre extracteur
de jus pour la première fois.
Afin d’éliminer les risques de
suffocation, retirez et jetez en
lieu sûr l’enveloppe protectrice
recouvrant la fiche de l’appareil.
Déroulez complètement
le cordon d’alimentation
avant usage.
Ne placez pas l’extracteur
sur le bord d’un comptoir ou
d’une table. Assurez-vous que
la surface de travail est de
niveau, propre et bien sèche.
Assurez-vous toujours que
l’extracteur est correctement
assemblé avant de l’utiliser.
Table
des matières
BREVILLE |
COMMERCIAL
VOUS
RECOMMANDE
LA SÉCURITÉ
AVANT TOUT
Chez Breville | Commercial,
la sécurité occupe une place
de choix. Nous concevons et
fabriquons des produits de
consommation sans jamais
perdre de vue la sécurité de
notre précieuse clientèle.
De plus, nous vous demandons
d’être très vigilant lorsque vous
utilisez un appareil électrique
et de respecter les mesures
de sécurité suivantes.
2 Breville | Commercial vous
recommande la sécurité avant tout
7 Composants
8 Assemblage
9 Fonctions
11 Entretien & nettoyage
12 Guide de dépannage
14 Trucs
3
Assurez-vous toujours que le
panier filtre, le bol du panier filtre
et le couvercle de l’extracteur sont
bien enclenchés avant de mettre
l’appareil en marche.
Ne détachez pas le bras
de verrouillage lorsque
l’appareil fonctionne.
N’utilisez pas l’appareil si
le panier rotatif (panier
filtre) est endommagé.
Ne faites pas fonctionner
l’extracteur sans que le récipient
à pulpe soit en place.
Avant d’extraire le jus de
fruits ou de légumes, vérifiez
l’appareil et assurez-vous :
que toutes les pelures ou peaux
coriaces ont été enlevées;
que tous les pépins, noyaux
ou graines ont été enlevés;
que toutes les attaches ou fils
métalliques ont été retirés
Le fait de ne pas respecter
ces instructions pourrait
affecter le fonctionnement
adéquat de l’appareil et causer
de sérieuses blessures.
Ne branchez jamais l’extracteur
et ne le mettez pas en MARCHE
si des aliments sont dans
le tube d’alimentation.
Attendez que le moteur
atteigne la vitesse requise
avant d’insérer les aliments
dans le tube d’alimentation.
Ne mettez pas les doigts ou
autres objets dans l’ouverture
de l’extracteur lorsqu’il est
branché ou en marche. Si des
aliments sont coincés dans
l’ouverture, utilisez uniquement
le poussoir ou un morceau de
fruit ou de légume pour les
acheminer vers le bas. Si cette
méthode s’avère impossible,
éteignez l’appareil, démontez-le
et retirez les aliments coincés.
Évitez tout contact avec les
pièces en mouvement.
Assurez-vous d’éteindre
l’appareil après chaque usage.
Veillez à ce que le moteur soit
complètement immobilisé
avant de démonter l’extracteur.
Ne laissez pas l’extracteur
sans surveillance lorsqu’il
est en marche.
Avant de débranchez l’appareil,
tournez le cadran de contrôle
à ARRÊT, puis débranchez-le.
Afin d’éviter les fuites ou
débordements, nettoyez
soigneusement l’appareil et
le panier filtre après chaque
usage et assurez-vous qu’il
fonctionne comme prévu.
Soyez prudent lorsque vous
manipulez le panier filtre, car
les petites lames à la base du
panier sont très coupantes.
Une manipulation inadéquate
peut causer des blessures.
4
Éteignez l’appareil, puis
débranchez-le lorsqu’il n’est
pas utilisé, avant d’assembler
ou de retirer des pièces ou
avant de le nettoyer.
Pour le débrancher, saisissez
la fiche et retirez-la de la prise
murale. Ne tirez jamais sur
le cordon d’alimentation.
Cet appareil n’est pas destiné à
être utilisé par des enfants ou des
personnes ayant des capacités
physiques, sensorielles ou
mentales réduites ou un manque
d’expérience et de connaissances.
Une étroite surveillance est
requise lorsqu’un appareil est
utilisé à proximité d’enfants.
Les enfants doivent être
surveillés pour s’assurer qu’ils
ne jouent pas avec l’appareil.
Ne l’utilisez dans aucun type
de véhicule en mouvement ni
à l’extérieur. Ne l’utilisez pas à
d’autres fins que celles prévus.
Une mauvaise utilisation
peut causer des blessures.
L’utilisation d’accessoires
non recommandés ou
vendus par le fabricant peut
causer un risque d’incendie,
d’électrocution ou de blessures.
Pour vous protéger contre
le risque d’électrocution,
n’immergez pas le cordon, la
fiche ou le socle motorisé dans
l’eau (ou tout autre liquide).
Un exemple représentatif du
chargement le plus lourd à
être utilisé avec cet extracteur
équivaut à 5 kg de carottes
extraites en continu avec une
force de poussée de 5 kg.
NOTE
Si le moteur cale ou s’arrête sous
de lourdes charges, ne le faites
pas fonctionner en continu plus
de 10 secondes à la fois.
NOTE
Si l’extracteur s’arrête à cause
d’un fonctionnement inadéquat
ou s’il fait un bruit excessif,
éteignez l’appareil (ARRÊT)
et attendez que le panier filtre
cesse de tourner complètement.
Débranchez l’appareil,
démontez-le et nettoyez tous
les composants avant de le
assembler correctement.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52

Breville CJE830 Manuel utilisateur

Catégorie
Fabricants de jus
Taper
Manuel utilisateur

dans d''autres langues