GE Cafe Series CFCP1NIZSS Manuel utilisateur

GEAppliances.com

Refrigerators

Bottom Freezer

200D9366P023 49-60644-2 01-2012 GE

Safety Instructions . . . . . . . . . . .2, 3

Operating Instructions

Additional Features . . . . . . . . . . . . . . . . .9

Automatic Icemaker . . . . . . . . . . . .12,13

Care and Cleaning . . . . . . . . . . . . . .13,14

Controls . . . . . . . . . . . . . . . . . . . . . . . . . .4,5

Crispers and Pans . . . . . . . . . . . . . . . . .10

Freezer . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Replacing the Light Bulbs . . . . . . . . . .15

Shelves and Bins . . . . . . . . . . . . . . . . . .8, 9

Water Dispenser . . . . . . . . . . . . . . . . . . .13

Water Filter . . . . . . . . . . . . . . . . . . . . . . . . .6

Water Filter . . . . . . . . . . . . . . . . . . . . . . . . .7

Installation Instructions

Installing the Anti-Tip

Floor Bracket . . . . . . . . . . . . . . . . . . .19, 20

Installing the Refrigerator . . . . . .21–25

Installing the Water Line . . . . . . . .34–35

Preparing to Install

the Refrigerator . . . . . . . . . . . . . . . . . . . .18

Removing and Replacing the

Freezer Drawer . . . . . . . . . . . . . . . .26, 27

Reversing the Door Swing . . . . . .28–30

Removing and Replacing

the Doors . . . . . . . . . . . . . . . . . . . . .31–33

Trim Kits and Decorator Panels . . . .16, 17

Troubleshooting Tips . . . . . .37–41

Normal Operating Sounds . . . . . . . . . .37

Consumer Support

Consumer Support . . . . . . . .Back Cover

Performance Data Sheet . . . . . . . . . . .43

State of California Water

Treatment Device Certificate . . . . . . .44

Warranty for Canadian

Customers . . . . . . . . . . . . . . . . . . . . . . . . .42

Warranty for U.S. Customers . . . . . . .41

Réfrigérateurs

Congélateur inférieur

Refrigeradores

Congelador inferior

Write the model and serial

numbers here:

Model # ____________________

Serial #______________________

These numbers are found on a label

located on upper left or right side of

refrigerator compartment

Models 21 and 25

Manuel d’utilisation

et d’installation

Owner’s Manual and

Installation Instructions

Manual del propietario

y instalación

La section française commence à la page 45

La sección en español empieza en la página 89

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

Use this appliance only for its intended purpose as described in this Owner’s Manual.

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:



 This refrigerator must be properly installed

and located in accordance with the Installation

Instructions before it is used.



 Do not allow children to climb, stand or hang

on the shelves in the refrigerator. They could

damage the refrigerator and seriously injure

themselves.



 Do not touch the cold surfaces in the freezer

compartment when hands are damp or wet.

Skin may stick to these extremely cold surfaces.



 Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any other

appliance.



 Keep fingers out of the “pinch point” areas;

clearances between the doors and between the

doors and cabinet are necessarily small. Be careful

closing doors when children are in the area.



 In refrigerators with automatic icemakers, avoid

contact with the moving parts of the ejector

mechanism, or with the heating element that

releases the cubes. Do not place fingers or hands

on the automatic icemaking mechanism while the

refrigerator is plugged in.



 Unplug the refrigerator before cleaning and making

repairs.

NOTE: We strongly recommend that any servicing

be performed by a qualified individual.



 Setting either or both controls to 0 (off) does not

remove power to the light circuit.



 Do not refreeze frozen foods which have thawed

completely.

PROPER DISPOSAL OF THE REFRIGERATOR

Child entrapment and suffocation are not problems of

the past. Junked or abandoned refrigerators are still

dangerous…even if they will sit for “just a few days.” If

you are getting rid of your old refrigerator, please

follow the instructions below to help prevent

accidents.

Before You Throw Away Your Old

Refrigerator or Freezer:

 Take off the doors.

 Leave the shelves in place so that children may not

easily climb inside.

Refrigerants

All refrigeration products contain refrigerants,

which under federal law must be removed prior to

product disposal. If you are getting rid of an old

refrigeration product, check with the company

handling the disposal about what to do.

USE OF EXTENSION CORDS

Because of potential safety hazards under certain conditions, we strongly recommend against

the use of an extension cord.

However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United States)

or a CSA certified (in Canada), 3-wire grounding type appliance extension cord having a grounding type plug

and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.

DANGER! RISK OF CHILD ENTRAPMENT

2

3

GEAppliances.com

WARNING!

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

For personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped with a 3-

prong (grounding) plug which mates with a standard

3-prong (grounding) wall outlet to minimize the

possibility of electric shock hazard from this

appliance.

Have the wall outlet and circuit checked by a qualified

electrician to make sure the outlet is properly

grounded.

Where a standard 2-prong wall outlet is encountered,

it is your personal responsibility and obligation to

have it replaced with a properly grounded 3-prong

wall outlet.

The refrigerator should always be plugged into its

own individual electrical outlet which has a voltage

rating that matches the rating plate.

This provides the best performance and also prevents

overloading house wiring circuits which could cause a

fire hazard from overheated wires.

Never unplug your refrigerator by pulling on the

power cord. Always grip plug firmly and pull straight

out from the outlet.

Repair or replace immediately all power cords that

have become frayed or otherwise damaged. Do not

use a cord that shows cracks or abrasion damage

along its length or at either end.

When moving the refrigerator away from the wall, be

careful not to roll over or damage the power cord.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

4

About the controls with temperature settings.

The temperature controls are preset in the factory at 37°F for the refrigerator compartment and 0°F for

the freezer compartment. Allow 24 hours for the temperature to stabilize to the preset recommended

settings.

The temperature controls can display both the SET temperature as well as the actual temperature in the

refrigerator and freezer. The actual temperature may vary slightly from the SET temperature based on

usage and operating environment.

Setting either or both controls to OFF stops cooling in both the freezer and refrigerator compartments,

but does not shut off electrical power to the refrigerator.

NOTE: The refrigerator is shipped with protective film covering the temperature controls.

If this film was not removed during installation, remove it now.

Control style C, LCD External Controls (on some models)

H

OME

H

ELP

L

OCK

Hold for 3 Seconds

to activate Lock

T

URBO

C

OOL

E

NERGY

S

AVER

D

OOR

A

LARM

FREEZER

F0

REFRIGERATOR

F37

OPTIONSPRECISE FILL

ENERGY SAVER ON

Control style A, Internal Controls (on some models)

Control style D, External Controls (on some models)

Control styles A, B & D (on some models)

A

CTUAL

T

EMP

(FIG A)

(FIG B)

5

For Controls on the Door Models:

FIG. “A” To change the temperature, press and release the

WARMER or COLDER pad. The ACTUAL TEMP light will come

on and the display will show the actual temperature. To

change the temperature, tap either the WARMER or COLDER

pad until the desired temperature is displayed.

FIG. “B” To visualize the real temperature press and release

the ACTUAL TEMP pad. The display will show the actual

temperature for 10 seconds.

To change the temperature, tap either the WARMER or

COLDER pad until the desired temperature is displayed. The

SET TEMP light will come on during this process.

For Controls Inside the Refrigerator:

Opening the door displays the actual temperature. To change

the temperature, press either the WARMER or COLDER touch

pads until the desired temperature is displayed.

Once the desired temperature has been set, the temperature

display will return to the actual refrigerator and freezer

temperatures after 5 seconds. Several adjustments may be

required. Each time you adjust controls, allow 24 hours for the

refrigerator to reach the temperature you have set.

To turn OFF cooling system, tap the WARMER pad for either

refrigerator or freezer until the display shows OFF.

To turn ON cooling system, tap the COLDER pad for either

the refrigerator or freezer twice. The display will show the

preset temperature settings of

37°F

for refrigerator and

0°F

for

freezer.

Turning the cooling system OFF stops the cooling to

refrigerator, but it does not shut off the electrical power.

Changing the Temperature for Control Styles A & B

Changing the Temperature for Control Style C

To Change the Refrigerator Temperature:

Access By: Home > Refrigerator

Activate By: Using the arrows to select the desired temperature.

You must press ENTER to set the new temperature.

To change the Freezer temperature:

Access By: Home > Freezer

Activate By: Using the arrows to select the desired temperature.

You must press ENTER to set the new temperature.

Once the desired temperature has been set, the display will return

to the HOME screen and show the set temperatures underneath

the actual temperature display for several seconds.

Several adjustments may be required. Each time you adjust the

controls, allow 24 hours for the refrigerator to reach the

temperature you have set.

To turn OFF cooling system, tap the WARMER pad for either

refrigerator or freezer until the display shows OFF.

To turn ON cooling system, tap the COLDER pad for either the

refrigerator or freezer twice. The display will show the preset

temperature settings of 37°F for refrigerator and 0°F for freezer.

Turning the cooling system off stops the cooling to refrigerator, but

it does not shut off the electrical power.

For Controls on the Door Models:

FIG. “A” To change the temperature, press and release the

WARMER or COLDER pad. The ACTUAL TEMP light

will come on and the display will show the actual

temperature. To change the temperature, tap either the

WARMER or COLDER pad until the desired temperature is

displayed.

FIG. “B” To visualize the real temperature press and release

the ACTUAL TEMP pad. The display will show the actual

temperature for 10 seconds.

To change the temperature, tap either the WARMER or

COLDER pad until the desired temperature is displayed. The

SET TEMP light will come on during this process.

Once the desired temperature has been set, the temperature

display will return to the actual refrigerator and freezer

temperatures after 5 seconds.

Several adjustments may be required. Each time you adjust

controls, allow 24 hours for the refrigerator to reach the

temperature you have set.

To turn OFF cooling system, tap the refrigerator WARMER pad

until display flashes and beeps. Then tap the freezer WARMER

pad until display shows OFF.

To turn ON cooling system, tap the refrigerator COLDER

button twice. The display will show the refrigerator and freezer

set temperatures.

Turning the cooling system off stops the cooling to

refrigerator, but it does not shut off the electrical power.

Changing the Temperature for Control Style D

6

About TurboCool.

™

(on some models) GEAppliances.com

How It Works

TurboCool rapidly cools the refrigerator

compartment in order to more quickly

cool foods. Use TurboCool when adding a

large amount of food to the refrigerator

compartment, putting away foods after they

have been sitting out at room temperature

or when putting away warm leftovers. It can

also be used if the refrigerator has been

without power for an extended period.

Once activated, the compressor will turn on

immediately and the fans will cycle on and

off at high speed as needed for eight hours.

The compressor will continue to run until the

refrigerator compartment cools to

approximately 34°F (1°C), then it will cycle on

and off to maintain this setting. After 8 hours,

or if TurboCool is pressed again, the

refrigerator compartment will return to

the original setting.

How to Use

Press TurboCool. The refrigerator

temperature display will show .

After TurboCool is complete, the

refrigerator compartment will return

to the original setting.

NOTES: The refrigerator temperature

cannot be changed during

TurboCool.

The freezer temperature is not

affected during TurboCool.

When opening the refrigerator door

during TurboCool, the fans

will continue to run if they have

cycled on.

About Door Alarm (on some models)

The door alarm will sound if any door is open

for more than 2 minutes. The beeping stops

when you close the door.

(on some models)

About Energy Saver (on some models)

This product is equipped with an Energy

Saver feature. The refrigerator is shipped with

the Energy Saver feature enabled.

Over time, moisture can form on the front

surface of the refrigerator cabinet and cause

rust. If moisture does appear on the front

surface of the refrigerator cabinet, turn off

the Energy Saver feature by pressing and

releasing the ENERGY SAVER pad on the

control panel.

(on some models)

Water Filter Cartridge

The water filter cartridge is located in the back

upper right corner of the refrigerator

compartment.

When to Replace the Filter

There is a replacement indicator light for the

water filter cartridge on the temperature display.

This light will turn orange to tell you that you

need to replace the filter soon. The filter

cartridge should be replaced when the

replacement indicator light turns red or if the

flow of water to the dispenser or icemaker

decreases.

Installing the Filter Cartridge

If you are replacing the cartridge, first

remove the old one by slowly turning it to

the left. DO NOT pull down on the cartridge.

A small amount of water may drip down.

CAUTION: If air has been trapped

in the system, the filter cartridge may be ejected

as it is removed. Use caution when removing.

Remove the protective foil from the end of

the cartridge.

Fill the replacement cartridge with water

from the tap to allow for better flow from the

dispenser immediately after installation.

Lining up the arrow on the cartridge and the

cartridge holder, slowly rotate the cartridge

clockwise until it stops. When the cartridge is

properly installed, you will feel it “click” as it

locks into place. Do not overtighten.

Run 1

1

⁄2 gallons (about 3 minutes) from the

dispenser to clear the system and prevent

sputtering. See To Use the Dispenser section.

Press and hold the RESET WATER FILTER

pad (on some models) for 3 seconds.

NOTE: A newly-installed water filter cartridge

may cause water to spurt from the dispenser.

Filter Bypass Plug

You must use the filter bypass plug when a

replacement filter cartridge is not available. The

icemaker will not operate without the filter or

filter bypass plug.

Replacement Filters:

For the maximum benefit of your filtration

system, GE recommends the use of GE branded

SmartWater filters only. Using GE branded filters

in GE and Hotpoint refrigerators provides optimal

performance and reliability. GE branded

SmartWater filters are always the right choice

because they are patented and designed

specifically for GE products. GE SmartWater

filters meet rigorous industry NSF standards for

safety and quality that are important for

products that are filtering your water. GE has

not qualified non-GE branded filters for use in GE

and Hotpoint refrigerators and there is no

assurance that non-GE branded filters meet GE’s

standards for quality, performance and reliability.

To order additional filter cartridges

in the United States, visit our Website,

GEAppliances.com, or call GE Parts and

Accessories, 800.626.2002.

Filter Model MWF

Customers in Canada should consult

the yellow pages for the nearest Mabe Service

Center.

About the water filter. (on some models)

7

(on some models)

Cartridge

Holder

Cartridge

Holder

8

Rearranging the Shelves

To remove:

Remove all items from the shelf.

Tilt the shelf up at the front.

Lift the shelf up at the back and bring the

shelf out.

To replace:

While tilting the shelf up, insert the top

hook at the back of the shelf in a slot on

the track.

Lower the front of the shelf until the

bottom of the shelf locks into place.

Spillproof Shelves (on some models)

Spillproof shelves have special edges to help prevent spills from dripping to lower shelves. To

remove or replace the shelves, see Rearranging the Shelves.

About the shelves and bins. GEAppliances.com

Not all features are on all models.

Some models have wire shelves

that can be adjusted in the same

manner.

Shelves in the refrigerator compartment are adjustable.

Refrigerator Compartment

Slide-Out Spillproof Shelf (on some models)

The slide-out spillproof shelf allows you

to reach items stored behind others. The special

edges are designed to help prevent spills from

dripping to lower shelves.

To remove:

Remove all items from shelf.

Slide the shelf out until it stops.

Lift the front edge of the shelf until the

central tabs are above the front bar.

Continue pulling the shelf forward

until it can be removed.

To replace:

Place the rear shelf tabs just in front of the

central notches on the shelf frame.

Slide the shelf in until the central tabs are

slightly behind the front bar.

Lower the shelf into place until it is

horizontal and slide the shelf in.

Make sure that the shelf sits flat after

reinstallation and doesn’t move freely from side

to side.

Make sure you push the shelves all the way in

before you close the door.

The drop-down shelf gives you the use of another full-size shelf when you need

extra storage. It conveniently folds back out of the way when not in use, giving you

room for storage of larger items.

To use drop-down shelf:

Pull forward and down to drop the shelf into place.

Pull forward while lifting up to place the shelf out of the way.

Drop Down Shelf (on some models)

Non-Adjustable Bins on the Door

To remove: Lift the bin straight up, then

pull out.

To replace: Engage the bin in the molded

supports on the door and push down.

It will lock in place.

Adjustable Bins on the Door

Adjustable bins can easily be carried from

refrigerator to work area.

To remove: Lift bin straight up, then

pull out.

To replace or relocate: Slide in the bin just

above the molded door supports, and push

down. The bin will lock in place.

The snugger helps prevent tipping, spilling

or sliding of small items stored on the door

shelf. Grip the finger hold near the rear of the

snugger and move it to fit your needs.

About the additional features.

Not all features are on all models.

Non-Adjustable Beverage Rack

To remove: Lift the rack straight up, then pull

out.

To replace: Engage the rack in the molded

supports on the door and push down.

It will lock in place.

About the shelves and bins.

9

Adjustable Divider in Freezer Basket

The freezer basket has a divider that can be

both repositioned or removed.

To remove: Pull the divider forward until the

rear locating tabs are out of the slots. Turn

the divider slightly to the side to release the

front locating tabs and lift out.

To replace: Turn the divider slightly to one

side so the tabs on the front fit into the vent

slots on the basket. Position the divider so

the back locating tabs snap into place in the

back vent slots.

To reposition: Remove the divider. Slide the

divider left or right to the desired location and

replace as instructed above.

Optional Freezer Caddy

The optional freezer caddy fits over the front

edge of the bottom freezer basket and can

be removed or added as needed.

To remove: Lift the freezer caddy up.

To replace: Lower the freezer Caddy ensuring

the hook fits over the front edge of the

bottom freezer basket. Push down to secure.

Tabs

Caddy

10

About the crispers and pans. GEAppliances.com

Not all features are on all models.

Fruit and Vegetable Crisper

Excess water that may accumulate in the

bottom of the drawers or under the drawers

should be wiped dry.

Adjustable Humidity Crisper (on some models)

Slide the control all the way to the

HIGH setting to provide high humidity

recommended for most vegetables.

Slide the control all the way to the LOW

setting to provide lower humidity levels

recommended for most fruits.

Adjustable Temperature Deli Pan (on some models)

Slide the control all the way to the left for the

coldest temperature.

To remove:

Remove the fruit and vegetable drawers.

Pull the drawer out to the stop position.

Lift the lid to access the 4 swing locks.

Rotate all four swing locks to the unlock

position.

Lift the front of the drawer up and out.

To replace:

Make sure all four swing locks are in the

unlock position.

Place the sides of the drawer into the

drawer supports, making sure the swing

locks fit on the drawer slots.

Lock all four swing locks by rotating them

to the lock position.

Lower the lid and slide in the drawer.

Replace the fruit and vegetable drawers.

How to Remove and Replace the Deli Pan

Swing Locks

Location of controls may vary, but function remain the same.

11

Freezer Shelves and Baskets

A shelf above the ice storage bin

A half-width basket

A deep full-width basket with

divider

Basket Removal

To remove the deep full-width basket:

Open the freezer drawer until it stops.

Lift the freezer caddy up.

Pull the divider forward until the rear

locating tabs are out of the slots. Turn the

divider slightly to the side to release the

front locating tabs and lift out.

The freezer basket rests on the metal slide

brackets and is held in place with swing

locks.

Turn the swing locks from verticall to

horizontal position.

Open the refrigerator doors.

Lift the basket up and rotate it toward you.

Slide out from the side of the drawer.

When replacing the deep full-width basket:

Tilt the basket toward you and lower it

into the drawer.

Place the basket onto the metal slide

brackets and over the swing locks.

Turn the swing locks from horizontal to

vertical position to lock the basket

in place.

Turn the divider slightly to one side so the

tabs on the front fit into the vent slots on

the basket. Position the divider so the back

locating tabs snap into place in the back

vent slots.

Lower the freezer caddy ensuring the hook

fits over the front edge of the bottom

freezer basket. Push down to secure.

To remove the half-width basket:

Pull the basket out to the stop location.

Lift the basket up at the front to release it

from the slides.

Lift the back up and out of the slide.

CAUTION:Always be sure to

fully close this basket.

When replacing the basket, make sure that

the wire tabs and wire hooks on the sides

of the basket go into the slots in the top

of the upper basket slides.

About the freezer.

Not all features are on all models.

Appearance and features may vary

Appearance may vary

Tabs

Freezer Shelves and Baskets

Appearance and features may vary

Single Drawer Models

Double Drawer Models

A full-width upper basket in top

drawer

Ice Bucket

A deep full-width lower basket in

bottom drawer

Accessing Ice and Reaching the Power

Switch

To reach the icemaker power switch and access Ice,

open the Ice box door located on the refrigerator door

and remove the bucket.

About the automatic icemaker. GEAppliances.com

A newly installed refrigerator may take 12 to 24 hours to begin making ice.

Icemaker

Feeler Arm

Power

Switch

Green

Power Light

To access ice.

Ice Bucket

Mullion

To reach the power switch.

Icemaker Accessory Kit

If your refrigerator did not come already equipped with an automatic icemaker, an icemaker accessory kit is available at extra cost.

Check the back of the refrigerator for the specific icemaker kit needed for your model.

12

Automatic Icemaker (on some models)

The icemaker will produce seven cubes per cycle—

approximately 100–130 cubes in a 24-hour period,

depending on freezer compartment temperature, room

temperature, number of door openings and other use

conditions.

See below for how to access ice and reach the power

switch.

If the refrigerator is operated before the water

connection is made to the icemaker, set the power

switch in the O (off) position.

When the refrigerator has been connected to the water

supply, set the power switch to the l (on) position. The

icemaker power light will turn green when the freezer light

switch is pressed in or when the freezer door is closed.

The icemaker will fill with water when it cools to 15°F

(–10°C). A newly installed refrigerator may take 12 to 24

hours to begin making ice cubes.

You will hear a buzzing sound each time

the icemaker fills with water.

Throw away the first few batches of ice to allow the

water line to clear.

Be sure nothing interferes with the sweep

of the feeler arm.

When the bin fills to the level of the feeler arm, the

icemaker will stop producing ice. It is normal for several

cubes to be joined together.

If ice is not used frequently, old ice cubes will become

cloudy, taste stale and shrink.

NOTE: In homes with lower-than-average water pressure,

you may hear the icemaker cycle multiple times when

making one batch of ice.

NOTE: Set the power switch to the O (off) position if the

water supply is shut off.

(Ice & Water Models)

To access ice.

Ice Bin

Shelf

To reach the power switch.

(Single Drawer Models)

Accessing Ice and Reaching the Power

Switch

To reach the icemaker power switch, pull the shelf

above the ice bin straight out, Always be sure to replace

the shelf.

To access ice, simply pull the bin forward.

Ice Bin

Shelf

Power switch

Lift and pull

Ice Box Door

Accessing Ice and Reaching the Power

Switch (Double Drawer Models)

To reach the icemaker power switch,

open the top freezer drawer and remove the full-width

basket. Always be sure to replace the basket.

To access ice, open the bottom freezer drawer. The ice

bucket is located below the mullio. Pull it foward to

access the ice.

Ice Bucket and Dispenser

• Pull up and out on the ice bucket to remove it from the compartment .

• To replace the ice bucket, set it on the guide brackets and push until

the ice bucket seats properly.

• If bucket cannot be replaced, rotate the Ice Bucket Fork 1/4 turn

clockwise.

Extra Ice Storage

• There is additional ice storage in the freezer compartment drawer.

13

To Use the External Water Dispenser

(on some models)

Press the glass gently against the top of the dispenser

cradle.

The spill shelf is not self-draining. To reduce water spotting,

the shelf should be cleaned regularly.

If no water is dispensed when the refrigerator is first

installed, there may be air in the water line system. Press

the dispenser arm and run 1

1

⁄2 gallons to remove trapped

air from the water line and to fill the water system. To

flush out impurities in the water line, throw away the first

six glassfuls of water.

Locking the Dispenser

Press the LOCK pad for 3 seconds to lock the dispenser

and control panel. To unlock, press and hold the pad

again for 3 seconds.

Door Alarm

To set the alarm, press the DOOR ALARM pad. The indicator

light will illuminate. This alarm will sound if either door is

open for more than 2 minutes. The beeping stops when you

close the door.

Spill Shelf

Dispenser Cradle

To Use the Internal Water Dispenser (on some models)

The water dispenser is located on the left wall inside the

refrigerator compartment.

To dispense water:

Hold the glass against the recess.

Push the water dispenser button.

Hold the glass underneath the dispenser for 2–3

seconds after releasing the dispenser button. Water

may continue to dispense after the button is released.

If no water is dispensed when the refrigerator is first

installed, there may be air in the water line system. Press the

dispenser button for at least 2 minutes to remove trapped

air from the water line and to fill the water system. During

this process, the dispenser noise may be loud as the air is

purged from the water line system. To flush out impurities in

the water line, throw away the first 6 glassfuls of water.

NOTE: To avoid water deposits, the dispenser should be

cleaned periodically by wiping with a clean cloth or

sponge.

About the ice and water dispenser. (on some models)

To Use the External Dispenser (on some models)

Select CUBED ICE ,CRUSHED ICE or WATER.

Press the glass gently against the top of the

dispenser cradle.

The spill shelf is not self-draining. To reduce water

spotting, the shelf and its grille should be cleaned

regularly.

If no water is dispensed when the refrigerator is

first installed, there may be air in the water line

system. Press the dispenser arm for at least two

minutes to remove trapped air from the water

line and to fill the water system. To flush out

impurities in the water line, throw away the first

six glassfuls of water.

CAUTION: Never put fingers or any other

objects into the ice crusher discharge opening.

Locking the Dispenser

Dispenser Light

This pad turns the night light in

the dispenser on and off. The

light also comes on when the

dispenser cradle is pressed. If

this light burns out, it should be

replaced with a 6 watt 12V

maximum bulb.

Door Alarm (on some models)

To set the alarm, press this pad

until the indicator light comes

on. This alarm will sound if

either door is open for more

than 3 minutes. The light goes

out and the beeping stops

when you close the door.

Spill Shelf

Important Facts About Your Dispenser

 Do not add ice from trays or bags to

the storage drawer. It may not crush or dispense well.

 Avoid overfilling glass with ice and use

of narrow glasses. Backed-up ice can jam the chute or cause

the door in the chute to freeze shut. If ice is blocking the

chute, poke it through with a wooden spoon.

 Beverages and foods should not be quick-chilled in the ice

st

orage drawer. Cans, bottles or food packages in the

storage drawer may cause the icemaker or auger to jam.

 To keep dispensed ice from missing the glass, put the glass

close to, but not touching, the dispenser opening.

 Some crushed ice may be dispensed

even though y

ou selected CUBED ICE. This happens

occasionally when a few cubes accidentally get directed to

the crusher.

 After crushed ice is dispensed, some water may drip from

the chut

e.

 Sometimes a small mound of snow will form on the door in

the ice chute. This condition is normal and usually occurs

when you have dispensed crushed ice repeatedly. The snow

will eventually evaporate.

Press the Lock Controls pad for 3 seconds to lock the dispenser and

control panel. To unlock, press and hold the pad again for 3 seconds.

14

Care and cleaning of the refrigerator.

Cleaning the Outside

The dispenser drip area (on some models),

beneath the grille, should be wiped dry. Water

left in this area may leave deposits. Remove

the deposits by adding undiluted vinegar to

the well. Soak until the deposits disappear

or become loose enough to rinse away.

The dispenser cradle (on some models).

Before cleaning, lock the dispenser by

pressing and holding the Lock Controls pad

for 3 seconds. Clean with warm water and

baking soda solution – about a tablespoon

(15 ml) of baking soda to a quart (1 liter)

of water. Rinse thoroughly and wipe dry.

The door handles and trim. Clean with

a cloth dampened with soapy water.

Dry with a soft cloth.

Keep the outside clean. Wipe with a

clean cloth lightly dampened with kitchen

appliance wax or mild liquid dish detergent.

Dry and polish with a clean, soft cloth.

Do not wipe the refrigerator with a soiled

dish cloth or wet towel. These may leave

a residue that can erode the paint. Do not

use scouring pads, powdered cleaners,

bleach or cleaners containing bleach

because these products can scratch

and weaken the paint finish.

Cleaning the Inside

To help prevent odors, leave an open box of baking soda in the fresh food and freezer compartments.

Unplug the refrigerator before cleaning.

If this is not practical, wring excess moisture out of sponge or cloth when cleaning around switches, lights or controls.

Use warm water and baking soda solution – about a tablespoon (15 ml) of baking soda to a quart (1 liter) of water. This both

cleans and neutralizes odors. Rinse and wipe dry.

Use of any cleaning solution other than that which is recommended, especially those that contain petroleum distillates, can

crack or damage the interior of the refrigerator.

Avoid cleaning cold glass shelves with hot water because the extreme temperature difference may cause them to break.

Handle glass shelves carefully. Bumping tempered glass can cause it to shatter.

Do not wash any plastic refrigerator parts in the dishwasher.

Dispenser drip area

About the ice and water dispenser. (cont )

Precise Fill (on some models)

This water dispenser is equipped with a feature called Precise Fill. This

feature allows you to choose a precise amount of water. Units include

ounces, cups, pints or liters.

Models with External Dispensers

Access By: Home > Precise Fill > Set Amount

Activate By: Using the arrow buttons to select the desired amount.

Press MORE UNITS to select between CUPS, OUNCES, PINTS or LITERS.

Press the cup against the cradle and water will begin dispensing. It

will automatically stop when the amount set has been dispensed.

The display will show there is no water left to dispense, then reset.

NOTE: Do not leave the dispenser unattended when water is being

dispensed.

If you would like to stop dispensing water before the specified

amount has been dispensed, just remove the cup from the cradle.

The display will show the amount left to dispense.

15

Refrigerator Lights (on some models)

CAUTION: Light bulbs may

be hot.

Unplug the refrigerator.

To remove the light shield, grasp the

shield at the back and pull out to release

the tabs at the back.

Rotate the shield down and then forward

to release the tabs at the front of the

shield.

After replacing with an appliance bulb of

the same or lower wattage, replace the

shield.

Plug the refrigerator back in.

NOTE: Appliance bulbs may be ordered from

GE Parts and Accessories, 800.626.2002.

Freezer Light (on some models)

Replacing the light bulbs.

Turning the control to the 0 (off) position does not remove power to the light circuit.

CAUTION: Light bulbs may

be hot.

Unplug the refrigerator.

Remove the freezer basket for access.

The bulb is located at the rear of the

freezer inside a light shield.

To remove, grasp the shield at the top

and pull out to release the tabs at the

bottom.

After replacing with an appliance bulb of

the same or lower wattage, replace the

shield and freezer basket.

Plug the refrigerator back in.

LED Lighting – Module (on some models)

Appearance may vary

Light

Shield

LED Lighting – Individual (on some models)

LED lighting will need to be replaced by an

authorized technician.

Call 1.800.432.2737 in the United States. In

Canada, call 1.800.561.3344

16

Trim kits and decorator panels. GEAppliances.com

Read these instructions completely and carefully.

Before You Begin

Some models are equipped with trim kits that allow you to install door panels. You can order

pre-cut black or white decorator panels from GE Parts and Accessories, 800.626.2002, or you

can add wood panels to match your kitchen cabinets.

Panels less than 1/4″ (6 mm) thick

When installing wood panels less than 1/4″ (6 mm) thick, you need to create a filler panel, such as 1/8″

cardboard, that will fit between the face of the door and the wood panel. If you are installing the pre-cut

decorator panels, pre-cut filler panels are included in the kit. The combined thickness of the decorator or wood

panel and the filler panel should be 11/32″ (8.7 mm) with the panel itself being no larger than 1/4″ (6 mm).

For panel-required models

Panels 1/4” thick or less

1/4” max

The handle and the top and bottom trim stand in front of the surface of the door, which requires that the filler

be smaller in length and width than the panel. Use the guidelines below and tape the filler onto the back of the

panel.

Left Fresh Food Door

Freezer Door

Filler

2 1/2” (63.5 mm)

3/4” (19 mm)

Panel

Filler

2 1/2” (63.5 mm)

3/4” (19 mm)

Panel

Right Fresh Food Door

Filler

2 1/2” (63.5 mm)

3/4” (19 mm)

Panel

17

Trim kits and decorator panels.

Dimensions for Custom Wood Panels

3/4″ (19 mm) or Raised Panel

A raised panel design screwed or glued to a 1/4″ (6 mm) thick backing, or a 3/4″ (19 mm) routed board can be used. The raised

portion of the panel must be fabricated to permit clearances of at least 2″ (5.1 cm) from the handle side for fingertip clearance.

Panels thicker than 1/4″ (6 mm), up to 3/4″ (19 mm) max., will require that the outer 5/16″ (8 mm) of panel perimeter be no

thicker than 1/4″ (6 mm).

Weight limitations for custom panels:

Fresh Food 10 lbs. (4.5 kg) max. for each door

Freezer Door 18 lbs. (8 kg) max.

2” (5.1 cm)

Clearance

Handle Side

Appearance

Panel

Refrigerator

Door

1/4” (6 mm)

Thick Backing

3/4”

(19 mm)

Panels thicker than 1/4” (6 mm)

1/4” (6 mm) max

3/4” (19 mm)

5/16” (8 mm)

Right Fresh Food Door

Freezer Door

Top, right and

bottom

16 29/32” (42.9 cm)

5/16” (8 mm)

minimum at

1/4” (6 mm)

thickness

Raised portion

of panel

2” (51 mm)

minimum at

1/4” (6 mm)

thickness

Handle side

26 3/32”

(66.3 cm)

2” (51 mm) minimum at

1/4” (6 mm) thickness

Handle side

Left, right and

bottom sides

5/16” (8 mm) minimum at

1/4” (6 mm) thickness

35 29/32” (91.2 cm)

Raised

portion

of panel

38 15/16”

(98.9 cm)

Left Fresh Food Door

Top, left and

bottom

16 29/32” (42.9 cm)

5/16” (8 mm)

minimum at

1/4” (6 mm)

thickness

Raised portion

of panel

2” (51 mm)

minimum at

1/4” (6 mm)

thickness

Handle side

38 15/16

(98.9 cm)

1/8”

(3 mm)

1/8”

(3 mm)

1/8”

(3 mm)

1/8”

(3 mm)

1/8”

(3 mm)

1/4”

(6 mm)

1/4”

(6 mm)

1/4”

(6 mm)

1/4”

(6 mm)

1/4”

(6 mm)

1/8

(3 mm)

1/4

(6 mm)

Installation

Refrigerator

Instructions

Models 21 and 25

Questions? Call 800.GE.CARES (800.432.2737) or visit our Website at: GEAppliances.com

In Canada, call 1.800.561.3344 or visit our Website at: www.GEAppliances.ca

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT — Save these instructions for local

inspector’s use.

•

IMPORTANT — Observe all governing codes and

ordinances.

• Note to Installer – Be sure to leave these instructions with

the Consumer.

• Note to Consumer – Keep these instructions for future

reference.

• Skill level – Installation of this appliance requires basic

mechanical skills.

• Completion time – Refrigerator Installation

20 minutes

Water Line Installation

30 minutes

Anti-Tip Bracket Installation

20 minutes

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not covered

under the Warranty.

PREPARATION

MOVING THE REFRIGERATOR INDOORS

If the refrigerator will not fit through a doorway, the

refrigerator door and freezer drawer can be removed.

• To remove the refrigerator door, see Step 1 in the

Reversing the Door Swing section.

• To remove the freezer drawer, see the Removing the

Freezer Drawer section.

WATER SUPPLY TO THE ICEMAKER AND DISPENSER

(ON SOME MODELS)

If the refrigerator has an icemaker, it will have

to be connected to a cold water line. A GE water supply kit

(containing tubing, shut-off valve, fittings and instructions) is

available at extra cost from

your dealer, by visiting our Website at GEAppliances.com (in

Canada at www.GEAppliances.ca) or from Parts and

Accessories, 800.626.2002 (In Canada 1.800.661.1616).

TOOLS YOU MAY NEED

Adjustable Wrench

1/4” Outer Diameter

Compression Nut

and Ferrule (sleeve)

(icemaker models only)

Phillips-Head Screwdriver

18

3/8” and 5/16” Socket

Ratchet/Driver

3/32”, 1/8” and 1/4” Allen

wrenches

MATERIALS YOU MAY NEED (not included)

Pencil

1/8” Drill Bit and

Electric or Hand Drill

Tape measure

1/4” Nut Driver

Lag Bolts

Anchor Sleeves

For Anti-Tip Bracket Mounted on CONCRETE Floors Only

Drill Bit Appropriate for Anchors

Wire Cutters

Level

LOCATING THE ANTI-TIP

FLOOR BRACKET

Place the anti-tip floor bracket locator template

(included inside the anti-tip kit) onto the floor

up against the rear wall, within W, and in line

with the desired location of the RH side of the

refrigerator (see Figure 1).

Place the anti-tip floor bracket onto the locator

template with its RH floor holes lined up with

the floor holes indicated on the template sheet,

approximately 7

1

⁄4″ from the edge of the sheet

or the RH side of the refrigerator.

Hold down in position and use the anti-tip floor

bracket as a template for marking the holes

based upon your configuration and type of

construction as shown in Step 3. Mark the hole

locations with a pencil, nail or awl.

NOTE:

• It is REQUIRED to use at least 2 screws to

mount the floor bracket (one on each side of

the anti-tip floor bracket). Both must be into

either the wall or the floor. Figure 2 indicates

all the acceptable mounting configurations

for screws. Identify the screw holes on the

anti-tip floor bracket for your configuration.

MEASURE CABINET OPENING

AVAILABLE VS. REFRIGERATOR

WIDTH

Measure width of cabinet opening where

refrigerator will be placed, W.

Be sure to account for any countertop

overhang, baseboard thickness and any

clearance desired. Width, W, should not be less

than 36 inches. The refrigerator will be placed

approximately in the middle of this opening.

WARNING

Under certain circumstances, this refrigerator

can tip forward.

Injury to persons can result.

Install Anti-Tip Bracket packed with this

refrigerator.

1

Baseboard

Thickness

or Countertop

Overhang

(Whichever

Is Greater) Plus

Any Desired

Clearance

Rear Wall

Front

RH Side

2

A

B

C

W

Base

Bracket

on the

Refrigerator

2 Wall Holes

RH Side of

Refrigerator

Floor – Concrete

(2 Holes)

Floor – Wood

(2 Holes)

7

1

⁄4″

Locator Template

Sheet

Floor Bracket

to Install

RH Holes

Rear RH Corner

of Cabinet Wall

REFRIGERATOR

Figure 1 – Installation Overview

19

Installation Instructions

INSTALLING THE ANTI-TIP FLOOR BRACKET (on 21 ft. models)

Installation Instructions

LOCATING THE ANTI-TIP

FLOOR BRACKET (cont.)

2

Preferred Installation –

Wood

Preferred Installation –

Concrete

Minimum Acceptable #1 –

Wall Plate Stud

Minimum Acceptable #2 –

Wood Floor

Minimum Acceptable #3 –

Concrete Floor

Figure 2 – Acceptable Screw Placement

Locations

CONCRETE Wall and Floor Construction:

• Anchors required (not provided):

4 each 1/4” x 1 1/2” lag bolts

4 each 1/2” O.D. sleeve anchors

• Drill the recommended size holes for the

anchors into the concrete at the center of

the holes marked in Step 2.

• Install the sleeve anchors into the drilled

holes. Place the anti-tip floor bracket as

indicated in Step 2. Remove the locator

template from the floor.

• Install the lag bolts through the anti-tip floor

bracket and tighten appropriately.

WOOD Wall and TILE Floor Construction:

• For this special case, locate the 2 wall holes

identified in Fig. 1. Drill an angled 1/8” pilot

hole (approx. as shown in Fig. 3) in the center

of each hole.

• Mount the anti-tip floor bracket using the

Minimum Acceptable Installation #1, as

illustrated in Fig. 2.

C

B

ANTI-TIP BRACKET INSTALLATION

WOOD Wall and Floor Construction:

• Drill the appropriate number of 1/8” pilot

holes in the center of each floor bracket hole

being used (a nail or awl may be used if a drill

is not available) AND remove the locator

template from the floor.

• Mount the anti-tip floor bracket by fastening

the 2, or preferably 4, #10-16 hex-head

screws tightly into place as illustrated in

Figure 3.

3

A

POSITIONING THE REFRIGERATOR

TO ENGAGE THE ANTI-TIP FLOOR

AND BASE BRACKETS

Before pushing the refrigerator into the

opening, plug the power cord into the

receptacle and connect waterline (if equipped).

Check for leaks.

Locate the refrigerator’s RH side and move

back approximately in line with the RH side of

the cabinet opening, W. This should position the

anti-tip floor bracket to engage the anti-tip

base bracket on the refrigerator.

Gently roll the refrigerator back into the cabinet

opening until it comes to a complete stop.

Check to see if the refrigerator front lines up

with the cabinet front face. If not, carefully rock

the refrigerator forward and backward until

engagement occurs and you notice that the

refrigerator is fully pushed up against the rear

wall.

OPTIONAL: Adjust the rear (and front) wheel

height settings to fully engage the rear anti-tip

brackets, while also aligning the refrigerator

front with the cabinet front face.

4

A

C

B

D

Figure 3 – Attachment to

Wall and Floor

NOTE:

If you pull the refrigerator out and away from the

wall for any reason, make sure the anti-tip floor

bracket is engaged when the refrigerator is pushed

back against the rear wall.

Rear RH Corner of

the Refrigerator

Floor

Wall

Plate

Stud

Floor

Bracket

2 Screws

Must Enter

Wood or

Metal Stud

Wall

20

La page charge ...

GE Cafe Series CFCP1NIZSS Manuel utilisateur

GE Cafe Series CFCP1NIZSS Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents