Panasonic Attune Manuel utilisateur

Marque: Panasonic

Modèle: Attune

Catégorie: Équipement musical supplémentaire

Taper: Manuel utilisateur

Ce manuel convient également à

Before attempting to connect or operate this product,

please read these instructions carefully and save this manual for future use.

No model number suffix is shown in this Operating Instructions.

Order Taker

Operating Instructions

Model No. WX-T3020

ENGLISHFRANÇAIS

CAUTION

The FCC ID number for this radio equipment is listed below.

FCC ID: ACJ9TAWX-T3020

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

FCC Warning: This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

FCC Warning: The available scientific evidence does not show that any health problems are associated with using low

power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low power

wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used. Whereas high lev-

els of RF can produce health effects (by heating tissue), exposure to low-level RF that does not produce heating effects

causes no known adverse health effects. Many studies of low-level RF exposures have not found any biological effects.

Some studies have suggested that some biological effects might occur, but such findings have not been confirmed by addi-

tional research. WX-T3020 has been tested and found to comply with FCC radiation exposure limits set forth for an uncon-

trolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65.

FCC Warning: To assure continued FCC emission limit compliance, use only the provided power supply cord and shielded

interface cable when connecting this device to the computer. Also, any unauthorized changes or modifications to this equip-

ment would void the user's authority to operate this device.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device

may not cause harmful interference, and (2) this device must accept any interference received, including interference that

may cause undesired operation.

Responsible Party: Panasonic Corporation of North America

One Panasonic Way, Secaucus, NJ 07094

Technical Support Party: Panasonic Consumer Electronics Company

1707 N. Randall Rd., Elgin IL. 60123

Technical Support Tel No.: 886-472-6767

RSS-213

Operation is subject to the following two conditions: (1) this

device may not cause interference, and (2) this device must

accept any interference, including interference that may cause

undesired operation of the device.

The model number and serial number of this product may be

found on the surface of the unit.

You should note the model number and serial number of this

unit in the space provided and retain this book as a perma-

nent record of your purchase to aid identification in the event

of theft.

Model No.

Serial No.

For U.S.A.

CAUTION:

• Danger of explosion if battery is incorrectly replaced. Replace

only with the same or equivalent type.

• These servicing instructions are for use by qualified service per-

sonnel only. To reduce the risk of electric shock do not perform

any servicing other than that contained in the operating instruc-

tions unless you are qualified to do so.

For Canada

ICES-003

This Class A digital apparatus complies with Canadian ICES-003.

For Canada

ATTENTION:

A lithium-ion battery that is recyclable powers the prod-

uct you have purchased. Please call 1-800-8-BATTERY

for information on how to recycle this battery.

WARNING:

• This apparatus must be earthed.

• Apparatus shall be connected to a main socket outlet with a pro-

tective earthing connection.

• The mains plug or an appliance coupler shall remain readily

operable.

• To reduce the risk of fire or electric shock, do not expose this

apparatus to rain or moisture.

• The apparatus should not be exposed to dripping or splashing

and that no objects filled with liquids, such as vases, should be

placed on the apparatus.

• All work related to the installation of this product should be made

by qualified service personnel or system installers.

• To prevent injury, this apparatus must be securely attached to

the floor/wall in accordance with the installation instructions.

• The connections should comply with local electrical code.

• The risk of hearing impairment due to exposure to excessive

sound levels may be reduced by listening at lower volumes and

for shorter durations.

Limitation of Liability

THIS PUBLICATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING

BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, OR

NON-INFRINGEMENT OF THE THIRD PARTY'S RIGHT.

Disclaimer of Warranty

IN NO EVENT SHALL MATSUSHITA ELECTRIC INDUSTRI-

AL CO,. LTD. BE LIABLE TO ANY PARTY OR ANY PERSON,

EXCEPT FOR REPLACEMENT OR REASONABLE MAINTE-

NANCE OF THE PRODUCT, FOR THE CASES, INCLUDING

BUT NOT LIMITED TO BELOW:

(1) ANY DAMAGE AND LOSS, INCLUDING WITHOUT LIMI-

TATION, DIRECT OR INDIRECT, SPECIAL, CONSE-

QUENTIAL OR EXEMPLARY, ARISING OUT OF OR

RELATING TO THE PRODUCT;

(2) PERSONAL INJURY OR ANY DAMAGE CAUSED BY

INAPPROPRIATE USE OR NEGLIGENT OPERATION OF

THE USER;

(3) UNAUTHORIZED DISASSEMBLE, REPAIR OR MODIFI-

CATION OF THE PRODUCT BY THE USER;

(4) ANY PROBLEM, CONSEQUENTIAL INCONVENIENCE,

OR LOSS OR DAMAGE, ARISING OUT OF THE SYSTEM

COMBINED BY THE DEVICES OF THIRD PARTY.

ENGLISH

Important Safety Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that

produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider

than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are

provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obso-

lete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart

is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the appa-

ratus has been exposed to rain or moisture, does not operate normally, or has been dropped.

S3125A

Limitation of Liability ................................................................................................................................... 3

Disclaimer of Warranty ............................................................................................................................... 3

Important Safety Instructions ...................................................................................................................... 4

Preface ....................................................................................................................................................... 6

Features ...................................................................................................................................................... 6

Precautions ................................................................................................................................................. 6

Major Operating Controls and Their Functions ........................................................................................... 7

Battery Loading & Replacement ................................................................................................................ 9

■ Loading ................................................................................................................................................ 9

■ Replacement ........................................................................................................................................ 9

Connecting and Disconnecting the Headset Plug ..................................................................................... 9

Operating Procedures ................................................................................................................................ 10

■ Communications with Customers (TALK) ............................................................................................. 10

■ Communications with Other Store Personnel (PAGE) .......................................................................... 10

■ Control of the device control terminals ................................................................................................. 11

■ Double-Drive-Thru connections ........................................................................................................... 11

■ Manager Mode (Only one Headset) ..................................................................................................... 12

■ Canceling the Manager Mode ............................................................................................................. 12

■ Auto-Talk-Lock setup (for only one Headset) ....................................................................................... 13

Setup Procedures ....................................................................................................................................... 14

■ Opening the Switch Compartment ....................................................................................................... 14

■ DIP Switch Setup .................................................................................................................................. 14

■ ID Registration ...................................................................................................................................... 15

■ Deletion of ID ........................................................................................................................................ 15

Troubleshooting........................................................................................................................................... 16

Specifications ............................................................................................................................................. 17

Standard Accessory ................................................................................................................................... 18

Optional Accessories ................................................................................................................................. 18

CONTENTS

Preface

Order Taker WX-T3020 is exclusively designed for Panasonic Wireless Communication System, which is used with drive-thru

menu boards, etc. By using optional Headset WX-H3027, users can communicate with other store personnel and customers.

Features

• This Order Taker can be used with Center Module WX-C3010.

• 1.9 GHz DECT* is used with this Order Taker to prevent the interference from microwave ovens or wireless LAN used with

2.4 GHz DECT.

*Digital Enhanced Cordless Telecommunications

• Manager mode

It is possible to set the manager mode to one of the Order Takers registered in the center module. A person using this Order

Taker has the priority of communication.

• It is possible to select Direct Lane or A/B Lane according to double-drive-thru layouts.

• It is possible to select the Talk-Lock or Press-To-Talk mode.

• It is possible to select the Page-Lock or Press-To-Page mode.

Precautions

• Use only Battery WX-B3030.

• Follow the instructions of battery for care and handling.

• In combination with this product, refer to Battery Charger WX-Z3040 Operating Instructions.

• To prevent damages, unplug Headset WX-H3027 from Order Taker WX-T3020 when storing these products.

• Use the headset with the earphone pad attached. Otherwise, voice may become distorted or you may have difficulty in hear-

ing the voice.

• Turn off the Order Taker when not in use, in order to save the battery life.

• Do not use this product if you use an implanted electric medical equipment. That may cause the equipment to malfunction.

EJECT

!1 !2

yt r e w

–

VOL

Major Operating Controls and Their Functions

q Battery Lock [EJECT]

When removing the battery, slide out the lock.

When loading a battery, insert the battery until the lock

clicks.

Please note the direction that inserts the battery.

w Talk 1 Button [T1]

This button controls communications with the customer.

When the button is released, you can hear any customer

who is at the menu-board.

While the button is held down in the Press-To-Talk

mode, you can speak to the customer.

When the button is pressed in the Talk-Lock mode, you

can speak to the customer until you press the button a

second time.

e Talk 2 / A/B Lane Selection Button [T2, A/B]

This button can be set to two functions by the DIP switch

setting. Refer to P.14 "DIP Switch Setup".

[T2]

This button controls communications with the customer

on Lane B of double-drive-thrus.

When the button is released, you can hear any customer

who is at the menu board.

While the button is held down in the Press-To-Talk

mode, you can speak to the customer who is at the

menu board.

When the button is pressed in the Talk-Lock mode, you

can speak to the customer until you press the button a

second time.

[A/B]

This button switches from Lane A to B and vice versa.

The lane indicator i displays the selected lane in yellow

(A) or green (B).

r Page Button [P]

This button controls communications with store person-

nel.

When the button is released, you can hear the communi-

cations among store personnel.

While the button is held down in the Press-To-Page

mode, you can speak to store personnel.

When the button is pressed in the Page-Lock mode, you

can speak to the store personnel until you press the but-

ton a second time.

t Optional Function Button [R]

This button is intended for functional extension.

When the Order Taker is set in the manager mode and

this button is pressed, operation cannot be forwarded

for talking or paging. At that time, the Telephone

Indicator of the Center Module lights.

To recover the talk or page operation, press this button

again.

The Telephone Indicator is turned OFF and the talk and

page operation becomes possible.

y External Device Control Button [C]

Press and hold the C button to turn on the external

device.

u Power Indicator

The indicator shows the status as follows.

Green: Power is supplied, and the unit is operating.

Green blinking: Power is supplied and Manager mode

is activated.

Red: The battery requires recharging.

Red blinking: ID is not registered, or the center module

is set to the ID Registration mode.

i Lane Indicator

Lights yellow or green to indicate which the lane is in

operation.

Yellow: Lane A is selected.

Green: Lane B is selected.

Yellow blinking: Lane A is being selected, and either

the Talk or Page mode is activated.

Green blinking: Lane B is being selected, and either

the Talk or Page mode is activated.

o Volume Control Buttons [ ]

Pressing the respective buttons will increase or

decrease the sound level.

!0 Power Button [POWER]

Pressing the button will turn the Order Taker on.

Pressing the button again for 2 seconds or more will turn

the Order Taker off.

!1 Earphone Output Jack

This jack is used for connection with the Panasonic WX-

H3027 Headset.

!2 Microphone Input Jack

This jack is used for connection with the Panasonic WX-

H3027 Headset.

!3 Switch Compartment

Do not open the cover of this compartment. It should be

opened only by qualified service personnel or system

installers.

!4 Battery (Optional accessory)

Refer to p. 6 "Precautions".

+ VOL –

When inserting the battery, check the

positive and negative sides.

Do not hold the cable.

Do not pull this

part up and down.

Battery Loading & Replacement

Notes:

• Refer to the operating instructions included with the bat-

tery and battery charger.

• Prepare a fully charged battery.

• Battery replacement is recommended when the power

indicator lights up in red and a constant beep is heard in

the headset.

■ Loading

Insert the battery as shown in the figure.

Note: Be sure to insert it until the lock clicks.

■ Replacement

1. Slide the battery lock down.

2. Remove the battery.

Connecting and Disconnecting the Headset Plug

When connecting the headset plug to this product, hold the

plug and push it straight into the earphone output jack and

microphone input jack.

When disconnecting the headset plug from this product,

hold the plug and pull it straight out.

Do not hold the cable or pull the plug up and down.

Doing so may cause trouble.

Pull/insert the plug straight,

holding this part.

■ Communications with Other

Store Personnel (PAGE)

Store personnel wearing the headset can communicate with

each other without being heard by customers.

<When the Press-To-Page (PTP) mode is pre-

set>

1. Hold down the P button and speak into the microphone

of the headset at a normal level.

2. Release the button. Your voice will not be heard by the

other store personnel.

1. Press the P button and speak into the microphone of

the headset at a normal level.

2. Press the P button again. The lock will be released, and

your voice will not be heard by the other store person-

nel.

Note: A maximum of 4 operators can have a conversation at

the same time.

■ Communications with

Customers (TALK)

Any store personnel wearing the headset can communicate

bidirectionally with any customer who is at the menu board.

1. Select a proper sound level by pressing the button

or .

2. You will hear a beep in the headset when a vehicle

arrives at the menu board.

<When the Press-To-Talk (PTT) mode is pre-

set>

1. Hold down the T1 button and speak to the customer.

A short beep is heard in the headset.

2. Release the button. Your voice is not heard by the cus-

tomer.

1. Press the T1 button and speak to the customer.

A short beep is heard in the headset.

2. Press the button again. The lock is released, and your

voice is not heard by the customer.

Operating Procedures

+ VOL –

Hold down

Release

Press

Press again

Press

Press again

Hold down

Release

■ Control of the device control ter-

minals

The device control terminals of the center module can be

controlled through the Order Taker.

1. Hold down the C button. A short beep is heard from the

speaker of the headset and a connection will be made

toward the device control terminals of the center mod-

ule.

2. Release the C button. A short beep is heard twice from

the speaker of the headset and the connection will be

disconnected toward the device control terminals of the

center module.

■ Double-Drive-Thru connections

When Double-Drive-Thru connections are made with the

center module, any Order Taker is required to select the

center module of either Lane A or Lane B.

1. When a connection is made to Lane A, the lane indicator

is lit in yellow. Press the T2 button if you want to make a

connection changeover to Lane B. When connected to

Lane B, a voice of [Lane B] is heard from the speaker of

the headset and the lane indicator is lit in green.

2. While a connection is maintained to Lane B, the lane

indicator is lit in green. Press the T2 button if you want to

make a connection changeover to Lane A. When con-

nected to Lane A, a voice of [Lane A] is heard from the

speaker of the headset and the lane indicator is lit in yel-

low.

1. While a connection is maintained to Lane A, the lane

indicator is lit in yellow. Press the T2 button if you want

to make a connection changeover to Lane B. When con-

nected to Lane B, a voice of [Lane B] is heard from the

speaker of the headset and the lane indicator is lit in

green.

2. While a connection is maintained to Lane B, the lane

indicator is lit in green. Press the T1 button if you want to

make a connection changeover to Lane A. When con-

nected to Lane A, a voice of [Lane A] is heard from the

speaker of the headset and the lane indicator is lit in yel-

low.

Note: When Direct Lane Select is set, TALK is available by

selecting either lane pressing T1 or T2 button.

Hold down

Release

Press

■ Manager Mode

(Only one Headset)

Complete ID Registration to do this setting.

The Order Taker set to the Manager mode has following

functionality.

• The manager can interrupt store personnel's TALK or

PAGE at any time by monopolizing one channel by prior-

ity.

• The Manager hears audio from POS alone.

1. Hold down the power button for 2 seconds or more to

turn off the Order Taker.

2. While holding R and T1 simultaneously, press the power

button to turn on the Order Taker. The Order Taker

enters manager setting mode where the indicators and

buttons have different functions than in normal opera-

tion. You can hear "Connecting center module A" and

power indicator is an alternate blinking of red and green.

Also the Lane indicator A is blinking yellow.

When you want to register the manager in another cen-

ter module in a double-drive-thru environment, while

holding R and T2 simultaneously, press the power but-

ton to turn on the Order Taker. You can hear

"Connecting center module B" and the power indicator

blinks red and green. Also the Lane indicator B blinks

green.

3. If manager mode setting is successful, you can hear

"Manager" and the power indicator blinks green.

■ Canceling the Manager Mode

1. Hold down the power button for 2 seconds or more to

turn off the Order Taker.

2. When LANE A is set in the manager mode, keep press-

ing the R and T1 buttons simultaneously and start up the

power of Order Taker.

When LANE B is set in the manager mode, keep press-

ing the R and T2 buttons simultaneously and start up the

power of Order Taker.

The power indicator then blinks reciprocally in red and

green. A message of “Connecting Center Module A (or

B)” is heard from the Order Taker speaker.

3. When canceling of the manager mode is complete, reci-

procal blinking of the power indicator turns to continu-

ous lighting in green.

Keep holding down.

(Lane A)

Keep holding down.

(Lane B)

Hold down the power button for two seconds or more to turn off. Hold down the power button for two seconds or more to turn off.

Keep holding down.

(Lane A)

Keep holding down.

(Lane B)

■ Auto-Talk-Lock setup (for only

one Headset)

For a Order Taker where Auto-Talk-Lock is set up, it has a

function to select [Talk] automatically when the vehicle

detector has become active, and you can talk with the cus-

tomer at the menu board.

1. Confirm that the dip switch 1 of the headset is ON, the

dip switch 2 is set at the objective lane, and the power

of the headset is OFF.

2. Turn on the Order Taker. The message "Hello Headset

**" (** is the number of headset) is output from the

speaker of the headset, and the power indicator blinks

green and red alternately for 3 seconds. While the indi-

cator is blinking, press the T1 or T2 button. (LANE A: T1

button, LANE B: T2 button) Auto-Talk-Lock will be set

up, The message "Auto-Talk-Lock ON" is heard from the

speaker of the headset. When the T1 or T2 button is not

pressed, the Order Taker assumes an ordinary opera-

tion mode.

3. In the case of a failure in Auto-Talk-Lock setup, a voice

of [Failed] is heard from the speaker of the headset. In

this case, the same procedures should be followed from

Step 1 again.

Note: If the power of the Order Taker is turned OFF, all the

setting conditions for Auto-Talk-Lock will be canceled.

This setting should be carried out without fail when the

power supply is started up.

Caution: Setup of this product should only be performed by

qualified service personnel or system installers.

■ Opening the Switch

Compartment

1. Press the power button for 2 seconds or more to turn off

the Order Taker.

2. Unscrew the screw and open the switch compartment.

3. Set the switches.

4. After finishing the setup, replace the cover.

5. Turn on the Order Taker.

■ DIP Switch Setup

An eight-bit DIP switch is provided for system setups. The

initial settings are marked with an asterisk *.

Note: Be sure to turn off the Order Taker in Step 1.

Otherwise, the DIP Switch will not be activated until you

turn the power off and on again.

1. Press the power button for 2 seconds or more to turn off

the Order Taker.

2. Set the switches as follows.

SW#1: This switch selects Auto Talk Lock ON/OFF

ON: Auto Talk Lock ON

OFF: Auto Talk Lock OFF

SW#2: This switch selects the target lane for "SW#1:

Auto Talk Lock".

ON: Lane B

OFF: Lane A

SW#3: This switch selects Direct Lane Select Mode or

Normal.

ON: Direct Lane Select Mode

When double-drive-thru, the T1 button is for lane

A, the T2 button is for lane B.

OFF: Normal

For double-drive-thru, the T2 button is A/B Lane

Selection.

SW#4: This switch selects Talk-Lock or Press-To-Talk

ON: Talk-Lock

OFF: PTT (Press-To-Talk)

SW#5: This switch selects Page-Lock or Press-To-Page.

ON: Page-Lock

OFF: PTP (Press-To-Page)

SW#6, SW#7: This switch selects language of Voice

Prompt.

Unscrew the

screw and open

the switch

compartment.

Press the power button to

turn off the Order Taker.

Setup Procedures

SW#

Auto Talk Lock ON/OFF

Function

Voice Prompt Language Select

OFF*

OFF

Auto Talk Lock LANE B A*

T2 Button Setting Direct Lane Select Normal*

Talk-Lock/Press-To-Talk Talk-Lock PTT*

Page-Lock/Press-To-Page Page-Lock PTP*

RF Power Reduce Power Full Power*

Initial Setting

OFF

SW#6

OFF*

OFF

OFF*

OFF

English

Spanish

French

Voice Prompt OFF

SW#7 Language

SW#8: This switch selects RF Power.

ON: Reduce Power

OFF: Full power

■ ID Registration

1. Press the ID Registration button of the center module for

2 seconds or more. The system is changed to the ID

Registration mode.

2. While holding down the T1 and T2 buttons simultaneous-

ly, hold down the power button to turn on the Order

Taker. The Order Taker enters the ID Registration setting

mode where the indicators and buttons have different

functions than in normal operation. You will hear "ID

Registration Mode" and the power indicator will blink yel-

low.

3. Press the T1 button, the Order Taker searches for the

center module. You can hear "Connecting center mod-

ule A" and the lane Indicator will blink yellow.

* Press the T2 button (at double-drive-thru), for other cen-

ter modules. You can hear "Connecting center module

B" and the lane indicator will blink green.

When the ID Registration succeeds, you will hear

"Registration Complete" and the headset number, and

the power indicator stops blinking and stays on.

4. When IDs are registered on all Order Takers, press the

ID Registration button of the center module, ID registra-

tion mode is completed. The power indicator of the

Order Taker will change from yellow to green.

Notes:

• If ID registration fails, a warning sounds "beep" and then

you will hear a voice prompt say "Failed". If registration

fails, the ID is not registered and the "Power" indicator

blinks red.

If this happens, turn off the power and try registering

again.

• All-in-One Headset or Order Taker that can register in

one center module is up to 32.

If you register IDs exceeding 32, the unused ID that has

been registered is automatically deleted in chronological

order.

• If ID registration is performed for 2 or more headsets,

follow the steps 2-4 individually.

■ Deletion of ID

To delete the registered ID of Order Taker follow the steps

below.

1. Hold down the POWER button for more than 2 seconds

to turn off the power of Order Taker.

2. To delete an ID that is registered for LANE A, keep

pressing the T1 and C buttons simultaneously and start

up the power of Order Taker.

To delete an ID that is registered for LANE B, keep

pressing the T2 and C buttons simultaneously and start

up the power of Order Taker. The power indicator then

blinks in yellow.

3. Press the P button while the power indicator keeps blink-

ing in yellow. The ID that is registered for LANE A (or

LANE B) is deleted.

4. The power indicator turns to blinking in red. A message of

“ID is not registered” is heard from the Order Taker

speaker.

Power on.

Keep holding down.

(Lane A)

Keep holding down.

(Lane B)

Troubleshooting

The headset ID is not registered in the center module of the tar-

get.

→ Register ID in the center module of the target.

Symptom

The power indicator blinks

red.

Reference

pages

Cause/solution

The battery is almost exhausted.

→ Recharge the battery.

(Refer to the operating instructions of the battery charger.)

The power indicator lights red

and a constant beep is heard

in the headphone.

–

Cannot turn on the Order

Taker.

The battery is exhausted. The battery is not inserted correctly.

→ Recharge the battery. Position the battery properly.

Cannot communicate with

other store personnel or the

customer at the menu board.

The center module may be turned off.

→ Turn on the power switch of the center module. (Refer to the

operating instructions of the center module.) If no remedy

exists, consult your dealer for repairs.

–

The headset ID is not registered in the center module of the tar-

get.

→ Register ID in the center module of the target.

Cannot hear or talk to the

customer, but

communications with the store

personnel are OK.

The vehicle detector may be malfunctioning because the detector

is not plugged into the center module, no power is supplied, or

the detecting function is out of order.

→ Check that the vehicle detector is plugged in and has power.

(Refer to the operating instructions of the center module.)

If no remedy exists, consult your dealer for repairs.

–

Cannot "page" or "talk" in

certain areas.

Talk or page operation is

impossible from the Order

Taker set in the manager

mode.

Radio waves cannot reach the area.

→ Remove any metal obstacles blocking radio waves.

Check that the Telephone Indicator of the Center Module is not

turned ON.

If the indicator is turned ON, the Optional Function Button [R] is

turned ON.

→ Press the Optional Function Button [R] again and check that

the Telephone Indicator is turned OFF.

–

Specifications

Operating Frequency: 1 920 - 1 930 MHz

Required Power Supply: Rechargeable Li-ion Battery, 3.7 V DC

Control Function: Power (On/Off)

Volume (Up/Down)

Talk (T1/T2)

Page

Lane Selection (A/B)

External Device Control (C)

DIP Switch Setup (8 bit)

Dimensions: 121 mm (W) x 61 mm (H) x 24 mm (D)

{4-3/4" (W) x 2-13/32" (H) x 15/16" (D)}

Weight (excluding battery): 115 g {0.25 lbs}

Ambient operating temperature: –10 °C to +50 °C {14 °F to 122 °F}

Dimensions and weighs indicated are approximate.

Specifications are subject to change without notice.

Optional Accessories

Battery (Li-ion 3.7 V DC, 1 100 mAh) ............................... WX-B3030

Battery Charger ................................................................ WX-Z3040

Headset ............................................................................ WX-H3027

Standard Accessory

Operating Instructions (this manual) ................................ 1 pc.

RSS-213

L'utilisation de ce dispositif est autorisée seulement aux deux

conditions suivantes : (1) il ne doit pas produire de brouillage,et

(2) l'utilisateur du dispositif doit être prêt à accepter tout brouil-

lage radioélectrique reçu, même si ce brouillage est susceptible

de compromettre le fonctionnement du dispositif.

ATTENTION:

• Risque d'explosion si la batterie n'est pas placée correctement.

Remplacer uniquement avec le même type ou un type

équivalent.

• Ces instructions de dépannage sont uniquement destinées au

personnel technique professionnel. Afin de limiter tout risque

d'électrocution, ne jamais exécuter de dépannage autre que

celui spécifié dans la notice d'instructions à moins que vous

possédiez des qualifications pour le faire.

Le numéro de modèle et le numéro de série de ce produit se

trouvent sur la surface de l'appareil.

Nous vous conseillons de relever le numéro de série de votre

appareil dans l'espace réservé ci-dessous et de conserver

précieusement votre notice d'instructions en tant que

justificatif d'achat aux fins d'identification en cas de vol.

No. de modèle

No. de série

FRANÇAIS

VERSION FRANÇAISE

(FRENCH VERSION)

AVERTISSEMENT:

• Cet appareil doit être mis à la terre.

• Le périphérique doit être connecté à une prise de sortie secteur

munie d'une connexion de mise à la terre de sécurité.

• La prise de sortie secteur ou l'adaptateur d'alimentation du

périphérique doit toujours être prêt à être utiliser.

• Ne jamais exposer cet appareil à la pluie ni le laisser dans un lieu

humide sous peine de créer un amorçage électrique ou une

électrocution.

• L'appareil ne devrait pas être exposé à des éclaboussures ou

des projections d'eau et aucun récipient rempli de liquide tels que

des vases ne devraient être posé sur l'appareil.

• Tous les travaux d'installation de ce produit devraient être confiés

à des techniciens et dépanneurs professionnels ou des

installateurs de système.

• Pour éviter tout accident corporel, cet appareil doit être

solidement fixé au sol/au mur conformément aux directives

d'installation.

• Les connexions doivent être conformes au code électrique local.

• Le risque d'affaiblissement du système auditif dû à une

exposition à des niveaux sonores excessifs peut être limité par

une écoute à des volumes inférieurs et de plus courtes durées.

NMB-003

Cet appareil numérique de la classe A est conforme à la norme

NMB-003 du Canada.

Limitation de responsabilité

CETTE PUBLICATION EST FOURNIE "COMME TEL" SANS GARANTIE DE TOUTE SORTE, EXPRÈS OU IMPLICITE, ÉTANT

INCLUSE MAIS NON LIMITÉE AUX GARANTIES IMPLICITES DE LA VALEUR MARCHANDE, ADAPTATION POUR TOUT BUT

PARTICULIER OU NON-INFRACTION DES DROITS D'UN TIERS.

Déni de la garantie

EN AUCUN CAS MATSUSHITA ELECTRIC INDUSTRIAL

CO., LTD. NE SERA TENU POUR RESPONSABLE POUR

TOUTE PARTIE OU TOUTE PERSONNE, À L'EXCEPTION

DU REMPLACEMENT OU D'UNE MAINTENANCE

RAISONNABLE DE CE PRODUIT POUR LES CAS CITÉS,

INCLUS MAIS NON LIMITÉS À CE QUI SUIT:

(1) TOUT DÉGÂT ET PERTE, Y COMPRIS SANS

LIMITATION, DIRECT OU INDIRECT, SPÉCIAL,

IMPORTANT OU EXEMPLAIRE, SURVENANT OU

CONCERNANT LE PRODUIT;

(2) BLESSURE PERSONNELLE OU TOUT DÉGÂT CAUSÉS

PAR UN USAGE NON APPROPRIÉ OU UNE

UTILISATION NÉGLIGENTE DE L'UTILISATEUR;

(3) DÉMONTAGE, RÉPARATION OU MODIFICATION NON

AUTORISÉS DU PRODUIT EFFECTUÉS PAR

L'UTILISATEUR;

(4) TOUT PROBLÈME, INCOMMODITÉ IMPORTANTE OU

PERTE OU ENDOMMAGEMENT, SURVENANT DU

SYSTÈME COMBINÉ PAR LES APPAREILS DE TIERS.

La page charge ...

Panasonic Attune Manuel utilisateur

Marque: Panasonic

Modèle: Attune

Catégorie: Équipement musical supplémentaire

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Panasonic Attune User manual

Documents connexes

Autres documents

HME EOS HD Operation Instructions Manual