BossPac EA000405 Border Router Manuel utilisateur

Taper
Manuel utilisateur
EA000405 BOARDER ROUTER
1
EA000405
Border Router
INSTRUCTION MANUAL
VERSION 1.0
EA000405 BOARDER ROUTER
2
VISIT OUR WEBSITE FOR MORE INFORMATION. WWW.BOSSPAC.COM
BOSSPAC ENGINEERING TECHNOLOGY, CALGARY HEAD OFFICE
PHONE: (403) 216-1226 FAX: (403) 216-5557 E-MAIL: INFO@BOSSPAC.COM
1450 28 STREET NE BAY 8, CALGARY, ALBERTA, CANADA T2A 7W6
EA000405 BOARDER ROUTER
3
Introduction
This manual provides basic information on how to commission or join a border router to any device:
Commission a Border Router onto an existing network
Joining a Border Router onto a network
Required Tools:
Computer (Run on Windows)
EA000405 Border Router
10 to 24V Power Supply
915 MHz Antenna
Ethernet Cable
o Physical connection to Personal Internet router.
915 MHz
Antenna
DRC Gateway
12V Power
Supply
Ethernet cable
EA000405 BOARDER ROUTER
4
1. Commission/Joining Border Router to a network
1 Installation
The EA000405 Border Router must be installed by a professional or certified technician
conversant with the certification requirements of the installation site.
The EA000405 Border Router requires a voltage between 10 VDC and 24 VDC capable of
supplying up to 2A.
Unless otherwise specified the EA000405 Border Router ships with a 3 dBi antenna
(EA002058). The EA000405 Border Router is compatible with the following antennas.
BossPac PN Gain
EH002058 (Standard) 3 dBi
EH002059 1.2 dBi
EH002060 8 dBi
EH000625 11 dBi
2 Commissioning
2.1 Set-up & Power On
- Connect one end of the Ethernet cable to your ethernet router.
- Connect the other end of the Ethernet cable to the border router (Figure 1)
Figure 1
- Connect the Power Supply corresponding wires to Border Router power port (Figure 2)
EA000405 BOARDER ROUTER
5
Figure 2
- Connect to the 915 MHz Antenna to Border Router (Figure 3)
Figure 3
- Power on/ Plug in the power Supply
2.2 SSH to Border Router
- On your laptop open Command prompt
- On command prompt type “ssh pi@###.###.##.##” “#” = Border Router IP address
- If connecting to the border router for the first time, command prompt will print “Are you
sure you want to continue connecting (yes/no)?”
- Type on command prompt “yes”
- If the border has a password, command prompt will ask you for a password in which then
you type password and then press enter.
- Command prompt will print “pi@###.###.##.##:~ $”
EA000405 BOARDER ROUTER
6
2.3 Joining, Commissioning and Starting a Network
2.3.1 Joining Ethernet Gateway to an existing network:
- On command prompt type “sudo ot-ctl” then press enter
- Command prompt will print “>”
- On command prompt type “ifconfig up” then press enter
- Command prompt will print “up”
- On command prompt type “joiner start 123456” then press enter’
- Command prompt will print “Done”, and if joining with the device is successful,
command prompt will print “joiner successful”
- On command prompt type “thread start” then press enter
- Command prompt will print “Done”
2.3.2 Commission a device to the network
- On command prompt type “sudo ot-ctl” then press enter
- Command prompt will print “>”
- On command prompt type “Commissioner start” then press enter
- Command prompt will print “Done” and “> Commissioner: active”
- On command prompt type “commissioner joiner add * 123456” then press enter
- Command prompt will print “Done”
- To close commissioner type on command prompt “commissioner stop” then press enter
- Command prompt will print “Commissioner: disabled” and “Done”
2.3.3 Start a Network
- On command prompt type “sudo ot-ctl” then press enter
- Command prompt will print “>”
- On command prompt type “dataset init new” then press enter
- Command prompt will print “Done”
- On command prompt type “dataset channel x”; where x represents the desired channel.
Valid numbers are between 1 and 10. then press enter
- Command prompt will print “Done”
- Type “dataset commit active”
- Command prompt will print “Done”
- Type “ifconfig up”
- Type “thread start”
-
EA000405 BOARDER ROUTER
7
FCC & IC Statements
FCC Class B Part 15
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by BossPac Engineering Technology Inc. may void the
user’s authority to operate the equipment.
ISED RSP-100 Statement
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de
brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
FCC/IC RF Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The
antenna(s) used for this equipment must be installed to provide a separation distance of at least 8 inches
(20cm) from all persons.
Cet équipement est conforme à l'exposition aux radiations de FCC et d'Industrie Canada établies pour un
environnement non contrôlé. L'antenne (s) utilisé pour cet équipement doit être installé pour fournir une
distance d'au moins 20cm à partir de toutes les personnes.
EA000405 BOARDER ROUTER
8
For further Technical Assistance
Email support@bosspac.com
Or call (866) 616-1226 or (403) 216-1226
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

BossPac EA000405 Border Router Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues