Honeywell Home RTH Series T5 Smart Thermostat Guide d'installation

T5 Smart

Thermostat

Programmable

Thermostat

Quick Install Guide

For more information visit honeywellhome.com

Mode

Menu Fan

Mode Fan

Heat Auto

Wake Away Home Sleep

Following Schedule

RCHT8610WF2006,

RCHT8610WF2014,

RCHT8610WF3005,

RCHT8612WF2005,

RCHT8612WF2015,

RCHT8612WF3006,

RTH8800WF2022,

Read before installing

2 3

Included in your box:

Screws and

anchors

UWP™

Mounting

System

(UWP)

T5 Smart

Thermostat

Quick Install

uide

2 3

Multiple programming options that fit your lifestyle:

1. LocationBased scheduling – The thermostat uses your smartphone’s

location to know when you’re away, and saves you energy. Through geofence

technology, it senses your return and helps make you comfortable upon arriv-

al. You can always manually change your preset Home and Away temperature

either on the thermostat or on the Resideo app.

2. Smart scheduling – Use a combination of geofencing and time schedul-

ing to fit your busy, active lifestyle.

3. TimeBased scheduling – Program your thermostat for one week; each

day (each day is a different schedule); MonFri, Sat, Sun; or MonFri, SatSun.

All days with four adjustable periods per day.

4. No scheduling – Control your comfort manually by adjusting temperature

set points only.

Smart Alerts. Push notifications remind you of filter changes and warn you of

extreme indoor temperatures.

Smart Response. Learns your heating and cooling system to deliver the opti-

mal temperature at the right time.

Auto Change From Heat to Cool. Automatically determine if your home needs

heating or cooling to provide maximum comfort.

Get the most from T5 Smart Thermostat

!

4

Tools you will need:

You may need:

Wire stripper

Needle-nose pliers Drill and

drill bit (7/32 in (5.6 mm))

Smartphone

To install your

thermostat and

photograph

existing wiring.

Resideo app

To conﬁgure your

system and connect

to your smartphone.

Small ﬂat head scr

ewdriver

Phillips scr

ewdriver

Pencil

Le

velHome Wi-Fi

Password

4 5

Compatibility

• Compatible with most heating, cooling, and heat pump systems

• Required: 24 VAC power (“C” wire)

• Does not work with electric baseboard heat (120240V)

• Does not work with millivolt systems

• Does not support input (S terminals) for indoor and outdoor sensors

• Does not support relay (U terminals) for ventilation

• Android or iOS smartphone, tablet, or device

For help, contact:

WEB honeywellhome.com

PHONE 18006333991

SOCIAL Twitter: @Honeywell_Home, Facebook: Honeywell Home

CAUTION: MERCURY NOTICE

If this product is replacing a control that contains mercury in a sealed tube, do not place the old

control in the trash. Contact your local waste management authority for instructions regarding

recycling and proper disposal.

CAUTION: EQUIPMENT DAMAGE HAZARD

Compressor protection is bypassed during testing. To prevent equipment damage, avoid cycling the

compressor quickly.

CAUTION: ELECTRICAL HAZARD

Can cause electrical shock or equipment damage. Disconnect power before beginning installation.

REQUIRED: 24 VAC POWER (“C” WIRE)

CAUTION: ELECTRONIC WASTE NOTICE

The product should not be disposed of with other household waste. Check for the nearest authorized

collection centers or authorized recyclers. The correct disposal of end-of-life equipment will help

prevent potential negative consequences for the environment and human health.

6 7

Removing your old thermostat

2 Check that your system is off

Change the temperature on your old

thermostat. If you don’t hear the system

turn on within 5 minutes, the power

is off.

Note: If you have a digital thermostat

that has a blank display, skip this step.

1 Turn power OFF

To protect yourself and your equipment,

Turn off the power at the breaker box

or switch that controls your heating/

cooling system.

3 Remove your old thermostat from the

wall plate

On most thermostats, you can take off

the thermostat by grasping and gently

pulling. Some thermostats may have

screws, buttons, or clasps.

Do not remove any wires from your

thermostat at this time!

75

OFF

ON

OFF

ON

75

Breaker box

Switch

6 7

5 Take a picture of how your wiring

looks right now

Be sure to include the letters next

to the terminals where the wires

are inserted. This will be a helpful

reference when wiring your thermostat.

Tip: If the color of your wires has faded

or if 2 terminals have the same wire

color, use the wire labels provided in

the package to label each wire.

4 Make sure there are no

120/240V wires

Do you have thick black wires with

wire nuts?

Is your thermostat 120V or higher?

If you answered yes to either of these

questions, you have a line voltage

system and the thermostat will not

work.

If you are unsure visit:

honeywellhome.com

6 Remove any jumpers

A jumper connects one terminal to

another terminal. It may look like a

small staple or even a colored wire and

must be removed before continuing.

Use a screwdriver to release wires from

terminals.

The thermostat does not

need jumpers.

YRRC

Example of

a jumper

Wire nut

Thick black wire

Terminals

1/4” to 3/8”

8 9

7 Record if you have wires in the following terminals

Do not include jumpers as a part of your count. The thermostat does not need

jumpers.

Terminal Wire Color

R

Rh

Rc

8 Write down the color of the wires

Check mark the wires that are connected to terminals. Next to the check mark,

write down the color of the wire. Do not include jumpers as a part of your count.

Check all that apply (Not all will apply):

Terminal Wire Color

Y

Y2

G

C

Terminal Wire Color

A or L/A

O/B

W2 or AUX

E

W

K

Required

S and U terminals are not supported with this thermostat.

If there are wires in terminals that are not listed, you will need additional wir-

ing support. Visit honeywellhome.com to find out if the thermostat will work

for you.

8 9

9 Disconnect the wires and remove the old wall plate

Use a screwdriver to release wires from terminals.

Tip: To prevent wires from falling back into the wall, wrap the wires

around a pencil.

10

Installing your T5 Smart Thermostat

T5 Smart Thermostat Screws UWP

Mounting

System Anchors Wall

10 11

11 Insert the wall anchors

It is recommended that you use the

wall anchors included in the box to

mount your thermostat.

You can use the UWP to mark where

you want to place the wall anchors.

a) Level the wall plate.

b) Mark the location of the wall

anchors using a pencil.

c) Drill the holes.

d) Insert wall anchors.

e) Make sure anchors are ﬂush with

wall.

Tip: Use a 7/32 (5.6 mm) drill bit.

10 Bundle and insert wires through

the UWP

Pull open the UWP and insert the

bundle of wires through the back of

the UWP.

Make sure at least 1/4-inch

(6.4 mm) of each wire is exposed for

easy insertion into the wire terminals.

12

12 Set R-switch position and insert R-wire or wires

Set the R-switch up or down based on your wiring notes in Step 7.

Insert wires into the inner holes of the terminals on the UWP. The tabs will

stay down once the wire is inserted.

If you have 1 R-wire (R, Rh, or Rc)

If you have 2 R-wires (R or Rh, and Rc)

or

1. Set R-switch to

the up position.

1. Set R-switch

to the down

position.

2. Insert your R-wire

(R, Rh or Rc) into

R-terminal.

2. Insert your Rc wire

into Rc-terminal.

3. Insert your R or Rh

wire into RTerminal.

12 13

13 Connect remaining wires from Step 8

Tip: Do not mount the UWP to the wall

prior to connecting the wires.

Depress the tabs to put the wires into

the inner holes of their corresponding

terminals on the UWP (one wire per ter-

minal) until it is firmly

in place.

Gently tug on the wires to verify they

are secure.

Tip: If you need to release the wires

again, push down the terminal tabs on

the sides of the UWP.

14 Mount the UWP and close the door

Mount the UWP using the provided

screws. Install all three screws for a

secure fit on your wall. Close the door

after you’re finished.

This wiring is just an example,

actual wiring may vary.

Use 3x

supplied

screws

#8 11/2”

(38.1 mm)

1/4” to 3/8”

14 15

16 Turn your power ON

Turn on the power at the breaker box

or switch that controls the heating/

cooling system.

OFF

ON

OFF

ON

90o

15 Attach your thermostat

Align the thermostat onto the

UWP and firmly snap it into place.

17 Return to the thermostat

Return to the thermostat. Confirm the

screen shows START SETUP. If it does,

continue to “Setup with Resideo App”

on page 15.

If your thermostat does not show

START SETUP, please contact

Resideo support.

Breaker box

Switch

14 15

1 Start Setup with the app

Touch START SETUP on thermostat.

Setup with Resideo App

No

Yes

Back

2 Select to setup with the app

Touch Ye s on the USE APP screen.

3 Your thermostat is now ready to be conﬁgured using the Resideo app

a.) Download the “Resideo” app from the App store or Google play.

b.) Open the Resideo app. Your thermostat should appear under Thermostat

Found. Tap SET UP NOW as shown below to continue. If your thermostat

doesn’t appear, create an account (if necessary), or sign in to your Resideo

account. Then select the T5 Smart Thermostat to install.

c.) The Resideo app will walk you through the rest of setup.

A B C

Thermostat Found:

SET UP NOW

16 17

How to use your Resideo App

SCHEDULEFANMODE

72˚

FOLLOWING SCHEDULE

72˚

MY HOME

Thermostat Access the

menu

Set desired

temperature

Schedule your home

comfort

Select System

mode Auto/Heat/

Cool/Off/EM Heat

Select Fan mode

Auto/On/Circulate.

Interested in more Resideo products? Visit honeywellhome.com to learn about all

available products connected by the Resideo App.

App is regularly enhanced and may change.

16 17

Mode

Menu Fan

Mode Fan

Heat Auto

How to use your T5 Smart Thermostat

The screen will wake up by touching the center area of displayed temperature.

Mode

Select system mode

Auto/Heat/Cool/Off/

EM Heat (emergency

heat).

Menu

Contains features:

schedule, screen lock,

ventilation, WiFi,

clean screen, and

other thermostat

settings.

Fan

Select Fan mode

Auto/On/Circulate.

Desired temperature

Displays desired

indoor temperature.

Indoor Temperature

Displays current

indoor temperature.

Adjust temperature

Touch + or - to set

your desired indoor

temperature.

18 19

If your WiFi network is not working, you can

alternatively setup your thermostat manually

and connect your phone later.

1 Start manual setup

Touch START SETUP to begin.

Manual Setup

Edit

No

Yes

3 Navigate and edit setup options

Use or to navigate through all the

setup options. To see a list of all setup

options, go to pages 2021.

To edit an option value, touch Edit or

touch text area.

The value is now blinking. Use or to

select the correct value.

Touch Done or touch text area once the

correct value is selected.

2 Select manual setup

On the USE APP screen, touch No.

18 19

4 Finish Setup

Touch until you see Finish Setup.

Touch Select or touch text area.

Manual Setup (cont.)

Select

No

Yes

Back

No

Yes

Back

5 Setup WiFi

At the end of setup process you will be

prompted to SETUP WIFI. If your WiFi

is still not working, you have to manually

set the time and date. Select No on the

SETUP WIFI screen.

6 Set time and date

Set daylight saving time if you are in an

area that follows daylight saving time. Set

date, clock format and time on the next

screens.

7 Your thermostat is now setup

Refer to page 17 for more information

about basic operation.

20 21

Equipment Setup Options

Option # Option Name Option Value (factory default in bold)

120 Schedule Type No Schedule

MOSU = Every day the same

MOFR SA SU = 511 schedule

MO-FR SA-SU = 5-2 schedule

Each Day = Every day different

Note: You can change default MO-FR, SA-SU schedule here. To edit

periods during days, temperature setpoints, or to turn Schedule On/

Off, touch MENU from the Home screen and go to SCHEDULE.

200 System Type Conventional Forced Air, Heat Pump, Boiler, Cool Only

Note: This option selects the basic system type your thermostat will

control.

205 Equipment Type Conventional Forced Air Heat:

Standard Gas, High Efficiency Gas, Oil, Electric, Fan Coil

Heat Pump:

Air to Air, Geothermal

Boiler:

Hot Water, Steam

Note: This option selects the equipment type your thermostat will

control. Note: This feature is NOT displayed if feature 200 is set to Cool

Only.

218 Reversing Valve O/B on Cool, 0/B on Heat

Note: This option is only displayed if the Heat Pump configured. Select

whether reversing valve O/B should energize in cool or in heat.

La page charge ...

Honeywell Home RTH Series T5 Smart Thermostat Guide d'installation

Ce manuel convient également à

Honeywell Home RTH Series T5 Smart Thermostat Guide d'installation

dans d''autres langues

Documents connexes

Autres documents