Optima Digital 1200 Manuel utilisateur

Marque: Optima

Modèle: Digital 1200

Catégorie: Chargeurs de batterie

Taper: Manuel utilisateur

Digital 12 0 0

12V Performance Charger

and Battery Maintainer

User Guide

Certificado a cumplir con:

Certifié conforme à :

UL 1236

CSA C22.2 No. 107.2

FCC Class B

Your Satisfaction is Important to Us!

Please do not return this product to the retailer or dealer for any service or warranty requirements.

For technical or warranty support please call OPTIMA® customer service at 1-888-867-8462 (888-8OPTIMA)

between 9am-5pm (CST) Monday through Friday, or via email at [email protected]

Thank you. OPTIMA® Customer Service.

WARNING - Failure to follow instructions may cause explosion, blindness or other serious injury.

Always shield eyes. Safety glasses should be worn when working with or near a battery.

IMPORTANT SAFETY INSTRUCTIONS

PLEASE READ & SAVE THESE INSTRUCTIONS

The Digital 1200 user guide contains important safety and operating instructions. In addition, important

safety warnings are often found on batteries and in vehicle owner’s manuals. Please read and follow all

of the warnings, the battery and vehicle manufacturer’s instructions and cautionary markings for the battery

you are charging before applying AC power and operating the Digital 1200 Charger.

Specifications subject to change without notice

02/12 A

OPTIMA

5757 N. Green Bay Ave.

Milwaukee, WI 53209

888.8OPTIMA (888.867.8462)

www.optimabatteries.com

Certified to:

UL 1236

CSA C22.2 No. 107.2

FCC Class B

Technical Specifications:

AC Input: 100 to 120 VAC, 60 Hz, 3.5 Amps

DC Output: Up to 14.9 VDC Digitally & Temperature Controlled

Charge Mode: Up to 12 Amps (Clamps), Up to 4 Amps (Aux.)

Maintain Mode: Up to 4 Amp (Clamps & Aux.)

DC USB Output: 5.0 VDC, Up to 1 Amp

Battery Types: AGM and Flooded (Lead Acid) Batteries

- 12V Auto / Marine

- 12V Motorcycle / Power Sports

12V OPTIMA and High Performance AGM Batteries

- Starting AGMs include OPTIMA RedTop & BlueTop

- Dual Purpose AGMs include OPTIMA YellowTop & BlueTop

Cables: 6’ AC and DC Cable, 6’ Maintainer Cable

Size: 10” x 7.5” x 6.5”

Weight: 4.8 lbs.

Especificaciones técnicas:

Entrada de CA: 100 a 120 V CA 60 Hz, 3.5 amperios

Salida de CC: Hasta 14.9 V CC (abrazaderas y aux.) control digital y de temperatura

Régimen de carga: Hasta 12 amperios (abrazaderas), hasta 4 amperios (aux.)

Modo de mantenimiento: Hasta 4 amperios (abrazaderas y aux.)

Entrada de USB CC: 5,0 V CC, hasta 1 amperio

Tipos de baterías: Baterías AGM e inundadas (plomo-ácido)

- 12 V para automóviles / uso marítimo

- 12 V para motocicletas / equipo deportivo

Baterías OPTIMA y AGM de alto rendimiento de 12V

- Las baterías de arranque AGM incluyen OPTIMA RedTop y BlueTop

- Las baterías AGM de doble propósito incluyen OPTIMA YellowTop y BlueTop

Cables: Cable de CA y CC de 6 pies, cable de mantenedor de 6 pies

Size: 25,4 x 19,1 x 16.5 cm

Weight: 2,18 kg

Caractéristiques techniques :

Entrée CA : 100 à 120 V c.a. 60 Hz, 3.5 ampères

Sortie CC : Jusqu’à 14,9 V c.c. (pinces et aux.) contrôle numérique et de température

Intensité de charge : Jusqu’à 12 ampères (pinces), jusqu’à 3 ampères (aux.)

Mode maintien : Jusqu’à 4 A (pinces et aux.)

Sortie USB c.c. : 5,0 V c.c., jusqu’à 1 A

Types de batteries : Batteries AGM et noyées (accumulateur au plomb)

- 12 V applications automobiles / nautiques

- 12 V applications moto / véhicules ATV

Batteries OPTIMA et AGM haute performance 12 V

- Les batteries de démarrage AGM incluent OPTIMA RedTop et BlueTop

- Les batteries AGM à double système incluent OPTIMA YellowTop et BlueTop

Câbles : Câble CA et CC de 6 pi, câble de mainteneur de 6 pi

Size: 25,4 x 19,1 x 16.5 cm

Weight: 2,18 kg

Digital 12 00

For use with 110 Volt 60 Hz AC power consistent with U.S. and Canadian standards

Year

Model Number: Digital1200 Serial Number: Date of Purchase:

PLEASE RECORD YOUR:

Introduction.......................................................................................................1

Important Safety Instructions..........................................................................2-6

Charger Location and DC Connection Precautions................................................7

In a Vehicle Charging Safety Precautions..............................................................8

Out of Vehicle Charging Safety Precautions..............................................................9

Handling Batteries............................................................................................10

Product Overview........................................................................................11-12

Getting to Know your Charger......................................................................13-16

Charging Battery Types and Approximate Charge Times...........................................17

Easy Set Up................................................................................................18-20

a. Charging with DC Charging Clamps out of a Vehicle....................................18

b. Charging with DC Charging Clamps in a Vehicle.......................................19

c. Auxiliary Side Port Maintainer Set Up......................................................20

Quick Set Operations..................................................................................21-23

a. Pre-Charge Status................................................................................21

b. Charging by Battery Type.......................................................................22

c. Auto-Maintaining Batteries by Connection Type.......................................23

Fault Screens and Trouble Shooting.............................................................24-25

Storage and Care...............................................................................................26

Technical Specifications....................................................................................26

Technical Support and Warranty.............................................................................27

Table of Contents

Digital 12 00 Digital 12 00

Thank you for your recent purchase of OPTIMA’s Digital 1200 12 Volt Performance Charger

and Battery Maintainer. OPTIMA® has taken 12 Volt performance automotive charging to new

levels of design and performance. Designed with advanced digital charging technology, the

Digital 1200 delivers multi-stage charging, conditioning, automatic battery maintaining and

reconditioning modes in addition to quick set controls and an industry leading LCD information

display center. The Digital 1200 is The Ultimate Power Source™ for all your battery charging

and maintaining needs. The ultra-premium Digital 1200 will fully charge and maintain all

types of 12 Volt batteries while significantly extending their lives.

Versatile Use:

For 12 Volt automotive, motorcycle, marine, tractor, power sports, RVs and more.

Benefits of OPTIMA’s Digital 1200 Charging Technology:

Microprocessor and software controlled charging.

Fully automatic, multi-stage performance charging, conditioning, maintaining and storage

reconditioning modes.

Enhances the performance of OPTIMA® and other AGM batteries.

Recovers deeply discharged batteries.

Extends battery life.

Auxiliary side port compatible with supplied cable for maintaining common pre-wired

battery maintainer installations.

Quick set, single touch operation for charging by battery type or storage maintain

modes by connection type.

LCD display for charging, maintaining and fault mode indication.

USB port for convenient charging and powering of USB supported devices and accessories.

Introduction Important Safety Instructions

SAVE THESE INSTRUCTIONS

This manual contains important safety and operating instructions for the OPTIMA® Digital

1200 12V Performance Charger and Battery Maintainer.

WARNING

To reduce the risk of injury to user or property; the user must read and understand the instruction

manual and all warnings on the charger and batteries before use.

WARNING

RISK OF EXPLOSIVE GAS MIXTURE. Read instructions in manual before using charger.

1. Connect and disconnect battery leads only when supply cord is disconnected.

2. For a battery installed in a vehicle, first connect charger output lead to ungrounded battery

post - not connected to automobile chassis - in accordance with polarity identification and then

opposite polarity lead to chassis away from battery; do not connect to carburetor or fuel

lines. Disconnect chassis lead first. For battery not installed in vehicle, refer to Instruction Manual.

3. Do not overcharge battery - See Instruction Manual.

4. Do not smoke, strike a match, or cause a spark in vicinity of battery.

5. Use in well-ventilated area.

6. Refer to Instruction Manual for further details.

WARNING

This equipment employs parts, such as switches and relays, that tend to produce arcs or sparks and

therefore, if used in a garage, locate in a room or enclosure provided for the purpose or not less than

18 inches above the floor.

CAUTION

Risk of Electric Shock. Connect only to properly grounded outlets.

Do not expose to rain or snow.

If cords or wires/cables become damaged return complete unit to OPTIMA for service/repair immediately.

CAUTION

1. WARNING - RISK OF EXPLOSIVE GASES.

a. WORKING IN THE VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS. BATTERIES

GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION. FOR THIS

REASON, IT IS OF UTMOST IMPORTANCE THAT YOU FOLLOW THE INSTRUCTIONS

EACH TIME YOU USE THE CHARGER.

b. To reduce risk of battery explosion, follow these instructions and those marked on the battery.

Review cautionary marking on these products and on engine.

2. Use charger for charging a LEAD-ACID battery only. It is not intended to supply power to an

extra-low-voltage eletrical system or to charge dry-cell batteries. Charging dry-cell batteries

may burst and cause injury to persons and property.

3. NEVER smoke, strike a match or cause a spark or flame in vicinity of battery or engine.

4. NEVER charge a frozen, damaged or leaking battery.

5. If it is necessary to remove battery from vehicle to charge it, always remove grounded terminal

from battery first. Make sure all accessories in the vehicle are off in order to prevent an arc.

3 4

Digital 12 00 Digital 12 00

Important Safety Instructions

6. Study all battery manufacturer’s specific precautions such as removing or not removing cell caps

while charging and recommended rates of charge.

7. For a charger having an output voltage selector switch, refer to the car owner’s manual in order

to determine the voltage of the battery and to make sure the output voltage is set at the correct

voltage. If an output voltage selector switch is not provided, do not use the battery charger

unless the battery voltage matches the output voltage rating of the charger.

8. Use of an attachment not recommended or sold by OPTIMA® may result in a risk of fire,

electric shock, or injury to persons.

9. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when

disconnecting charger.

10.Extension cords should not be used unless absolutely necessary. Use of an improper extension

cord could result in a risk of fire and electric shock. If an extension cord must be used make sure:

a. Pins on the plug of the extension cord are the same number, size and shape as those

on the plug of the charger.

b. Use only a properly wired extension cord in good electrical condition.

c. Use an industrial grade / heavy duty UL or CSA approved and grounded extension cord.

Check extension cord before use for damage, bent prongs, and cuts. Replace if damaged.

Always make your extension cord connection on the charger side first. After connecting

the extension cord to the charger proceed to plug the extension cord into a nearby 120

VAC GFCI protected (Ground Fault Circuit Interrupt) outlet. Below are manufacturer

recommendations for the right size UL or CSA Approved grounded extension cord.

i. Up to 50 feet in length use a 3 conductor 18 AWG extension cord.

ii. 50 to 100 feet in length use a 3 conductor 16 AWG extension cord.

iii. 100 to 150 feet in length use a 3 conductor 14 AWG extension cord.

11. Do not operate charger if any protective AC and DC cable insulation, charging clamps, DC fuse

holders and/or maintainer ring terminals have been damaged or compromised. Return the charger

for service and repair to OPTIMA® immediately.

12. Do not operate the charger if it has received a sharp blow, direct hit of force, been dropped or

otherwise damaged in any way. Return the charger for service and repair to OPTIMA® immediately.

13. Do not disassemble charger. Incorrect reassembly may result in a risk of electric shock or fire.

If service or repair is required please call OPTIMA® customer service at 1-888-867-8462

(888-8OPTIMA) between 9am-5pm (CST) Monday through Friday, or via email at

info@optimabatteries.com. Unauthorized attempts to service, repair or modify may result

in a risk of electrical shock, fire or explosion and will void warranty.

14. To reduce risk of electric shock, unplug charger from outlet before attempting any maintenance or

cleaning. Turning off controls will not reduce risk.

15. Do not expose charger to rain or snow

Important Safety Instructions

16. GROUNDING AND AC POWER CORD CONNECTION INSTRUCTIONS

a. Charger should be grounded to reduce risk of electric shock. Charger is equipped with

an electric cord having in equipment-grounding conductor and a grounding plug. The

plug must be plugged into an outlet that is properly installed and grounded in accordance

with all local codes and ordinances.

DANGER

Never alter AC cord or plug provided - If it will not fit outlet, have proper outlet installed by a qualified

electrician. Improper connection can result in a risk of an electric shock.

b.This battery charger is for use on a nominal 120-volt circuit, and has a grounding plug

that looks like the plug illustrated in figure A. A temporary adapter, which looks like the

adapter illustrated in figure B may be used to connect this plug to a two-pole receptacle

as shown in figure B if a properly grounded outlet is not available. The temporary

adapter should be used only until a properly grounded outlet can be installed by a

qualified electrician.

DANGER

Before using adapter as illustrated, be certain that center screw of outlet plate is grounded.

The green-colored rigid ear or leg extending from adapter must be connected to a properly

grounded outlet - make certain it is grounded. If necessary, replace original outlet cover plate

screw with a longer screw that will secure adapter ear or lug to outlet cover plate and make

ground connection to grounded outlet.

Use of an adapter is not allowed in Canada. If a grounding type receptacle is not available,

do not use this appliance until the proper outlet is installed by a qualified electrician.

Figure A

Grounding pin

Grounding means

Metal screw

Adapter Figure B

5 6

Digital 12 00 Digital 12 00

Important Safety Instructions

17. PERSONAL PRECAUTIONS

CAUTION

a. Consider having someone close enough or within the range of your voice to come to your

aid when you work near a lead-acid battery.

b. Have plenty of soap, water and baking soda nearby in case battery acid comes in contact with

skin, clothes or eyes.

c. Wear complete eye protection, hand and clothing protection. Avoid touching eyes while working

near a battery.

d. If battery acid contacts skin or clothing, wash immediately with soap and water. If acid enters

eye, immediately flood eye with running cold water for at least 15 minutes and get medical

attention immediately.

e. NEVER smoke, strike a match or cause a spark or flame in vicinity of battery or engine.

f. Be extra cautious to reduce risk of dropping a metal tool onto the battery. It might spark or

short-circuit a battery or other electrical hardware which may cause an explosion or fire.

g. Remove all personal metal items such as rings, bracelets, necklaces, watches, and jewelry

when working near a battery. A battery can produce a short circuit current high enough to

weld a ring or any other metal, causing serious burns.

h. Use charger for charging a LEAD-ACID battery only. It is not intended to supply power

to a low voltage electrical system other than in a start-motor application. Do not use

battery charger for charging dry-cell batteries that are commonly used with home

appliances. These batteries may burst and cause injury to persons and damage to property.

i. NEVER charge a frozen, damaged or leaking battery.

j. Keep other persons, children and pets away from batteries and your charger during operation

to avoid serious injury, death, fire or explosion.

k. Do not place the charger in the engine compartment or near moving parts. Place away from

the battery using the length of the DC cables.

l. Consult vehicle owner’s manual.

m. Do not use the charger’s auxiliary side port maintainer / cable assembly and the charger’s

DC charging clamps at the same time.

18. PREPARING TO CHARGE A BATTERY

CAUTION

a. When it is necessary to remove a battery from a vehicle to charge, make sure the engine

is off and all accessories in vehicle are off, as to not cause an arc. Always remove the

grounded negative terminal from the battery first.

b. Study all battery manufacturers’ specific precautions; warnings and instructions while charging

and recommended rates of charge. Never charge a battery with missing safety vent caps.

c. Be sure the area around the charger and batteries is well ventilated while the battery is being charged.

If the electrolyte is splashed into an eye, immediately force the eye open and flood it

with clean, cool water for at least 15 minutes. Get prompt medical attention.

If electrolyte is taken internally, drink large quantities of water or milk. DO NOT induce

vomiting. Get prompt medical attention.

Neutralize with baking soda any electrolyte that spills on a vehicle or in the work area.

After neutralizing, rinse contaminated area clean with water.

d. Clean battery terminals. Be careful to keep corrosion from coming in contact with eyes.

e. For flooded batteries with removable caps, ONLY ADD DISTILLED WATER in each cell

until electrolyte reaches levels specified by the battery manufacturer. Do not over fill.

For a maintenance free battery without removable caps, such as valve regulated lead

acid batteries, carefully follow manufacturer’s recharging instructions.

f. Determine voltage of battery by referring to the car owner’s manual and make sure the charger is

set for the correct 12V battery type. See “Charging Battery Types and Approximate Charge Times”.

g. Do not overcharge batteries by selecting the wrong battery type or by trying to charge

a non-12 Volt as defined by the 12 Volt battery types specified in this manual.

h. Do not use the charger’s auxiliary side port maintainer / cable assembly and the charger’s DC

charging clamps at the same time.

Important Safety Instructions

Digital 12 00 Digital 12 00

Charger Location & DC Connection

19. CHARGER LOCATION

CAUTION

a.Locate charger as far away from battery as DC cables permit.

b. Never place a charger directly above a battery being charged; gases or fluids from battery

will corrode and damage charger.

c. Do not operate charger in an enclosed area or in an area with restricted ventilation in any way.

d. Never allow battery acid to drip on charger when reading electrolyte specific gravity

or filling a battery.

e.Do not set a battery on top of charger.

f. Do not install on or over combustible surfaces.

20. DC CONNECTION PRECAUTIONS

CAUTION

a.Connect and disconnect DC output clips only after setting any charger switches to "off"

position and removing AC cord from electric outlet. Never allow clips to touch each other.

b.Attach charging clamps to battery and chassis as indicated in 21 (E), 21 (F) and 22 (b)

through 22 (d).

In Vehicle Battery Charging Safety Precautions

21.FOLLOW THESE STEPS WHEN BATTERY IS INSTALLED IN A VEHICLE. A SPARK

NEAR BATTERY MAY CAUSE BATTERY EXPLOSION. TO REDUCE RISK OF A SPARK

NEAR A BATTERY:

CAUTION

a.Position AC and DC cords to reduce risk of damage by hood, door or moving engine parts.

b.Stay clear of fan blades, belts, pulleys, and other parts that can cause injury to persons.

c.Check polarity of battery posts. POSITIVE (POS, P, +) battery post usually has a larger

diameter than the NEGATIVE (NEG, N, -) post.

d.Identify if you have a negative or positive grounded vehicle. This can be done by identifying

which battery post NEGATIVE (NEG, N, -) OR POSITIVE (POS, P, +) is connected to the chassis.

e.For a negative grounded vehicle: connect the RED POSITIVE (POS, P, +) cable clamp

or ring terminal first to the positive post of the battery, then connect the BLACK NEGATIVE

(NEG, N, -) cable clamp or ring terminal to the vehicle’s chassis. Do not connect the

black negative (NEG, N, -) cable clamp to metal fuel lines or anywhere in proximity of

the carburetor or the battery itself. Connect to a heavy gauge metal part of the frame

or engine block

f. For a positive grounded vehicle: connect the BLACK NEGATIVE (NEG, N, -) cable clamp

or ring terminal first to the negative post of the battery, then connect the RED POSITIVE

(POS, P, +) cable clamp or ring terminal to the vehicle’s chassis. Do not connect the red

positive (POS, P, +) cable clamp to metal fuel lines or anywhere in proximity of the carburetor

or the battery itself. Connect to a heavy gauge metal part of the frame or engine block

g.Connect charger ac supply cord to electric outlet.

h.When charging is completed always disconnect AC power, remove clip from vehicle chassis,

and then remove clip from battery terminal.

i. Plug charger into a properly grounded GFCI protected outlet.

j. See operating instructions for length of charge information.

k.Do not use an AC plug adapter of any kind.

109

Digital 12 00 Digital 12 00

Out of Vehicle Battery Charging Safety Precautions

22.FOLLOW THESE STEPS WHEN BATTERY IS OUTSIDE VEHICLE. A SPARK NEAR

BATTERY MAY CAUSE BATTERY EXPLOSION. TO REDUCE RISK OF A SPARK NEAR

A BATTERY:

CAUTION

a. Check polarity of battery posts. POSITIVE (POS, P, +) battery post usually has a larger

diameter than the NEGATIVE (NEG, N, -) post.

b. Attach at least a 60 cm 6-gauge (awg) insulated battery cable to a negative(NEG, N, –)

battery post.

c. Connect the RED POSITIVE (POS, P, +) cable clamp or ring terminal to the POSITIVE

(POS, P, +) post of battery.

d. Position yourself and free end of cable as far away from the battery as possible - then

connect the BLACK NEGATIVE (NEG, N, -) charger cable clamp or ring terminal to the

free end of cable

e. Do not face battery directly when making final connection.

f. Connect charger AC supply cord to electric outlet

g. When disconnecting charger, always do so in reverse sequence of connecting procedure

and break first connection while standing as far away from the battery as practical.

h. Plug charger into a properly grounded GFCI protected outlet.

i. Do not use an AC plug adapter of any kind.

j. A marine (boat) battery must be removed and charged on shore. To charge it on board

requires equipment specially designed for marine use.

Handling Batteries

WHEN HANDLING BATTERIES ALWAYS READ AND FOLLOW THE BATTERY MANUFACTURER

WARNINGS, INSTRUCTIONS AND CAUTIONARY MARKINGS

DANGER OF EXPLODING BATTERIES

Batteries contain sulfuric acid and produce explosive mixtures of hydrogen and oxygen gas. Because

self-discharge action generates hydrogen gas even when the battery is not in operation, make sure

batteries are stored and are used in a well-ventilated area. ALWAYS wear ANSI Z87.1 (U.S. standard)

approved safety glasses and face shield or splash proof goggles when working on or near batteries:

Always wear proper eye, face and hand protection.

Never try to charge a visibly damaged battery.

Do not attempt to charge a frozen battery.

Have plenty of soap, water and baking soda nearby in case battery acid comes

in contact with skin, clothes or eyes.

Keep all sparks, flames and cigarettes away from the battery.

Keep removable vents tight and level except when servicing electrolyte.

Never try to open a battery with non-removable vents.

Make sure work area is very well ventilated.

Never lean over battery while boosting, testing or charging.

Exercise caution when working with metallic tools or conductors to prevent short

circuits and sparks.

Make sure that the charger leads to the battery are not broken, frayed or loose.

If the battery becomes hot, or if violent gassing or spewing of electrolyte occurs,

immediately turn off the charger and have your local dealer test your battery.

HANDLING BATTERY ACID

Battery acid, or electrolyte, is a solution of poisonous sulfuric acid and water that can destroy clothing

and burn the skin. Use extreme caution when handling electrolyte and keep an acid neutralizing solution-

such as baking soda or household ammonia mixed with water- readily available. When handling batteries:

Always wear proper eye, face and hand protection.

If the electrolyte is splashed into an eye, immediately force the eye open and flood it

with clean, cool water for at least 15 minutes. Get prompt medical attention.

If electrolyte is taken internally, drink large quantities of water or milk.

DO NOT induce vomiting. Get prompt medical attention.

Neutralize with baking soda any electrolyte that spills on a vehicle or in the work area.

After neutralizing, rinse contaminated area clean with water.

DANGER / POISON

SHIELD EYES

EXPLOSIVE GASES

CAN CAUSE BLINDNESS

OR INJURY

SPARKS

FLAMES

SMOKING

SULFURIC ACID

CAN CAUSE

BLINDNESS OR

SEVERE BURNS

FLUSH EYES

IMMEDIATELY

WITH WATER

GET MEDICAL HELP FAST

KEEP OUT OF THE REACH OF CHILDREN. DO NOT TIP. KEEP VENT CAPS TIGHT AND LEVEL

1211

Digital 12 00 Digital 12 00

Product Overview

Digital 1200 Performance Features

The OPTIMA® Digital 1200 12 Volt charger boasts ultra-premium features and technology making

battery care, charging and maintaining batteries easier than ever before. Convenient features include

an in-clamp LED work light for connections in dark conditions and a 5 Watt USB charging port

compatible with iPad®, iPhone®, Android™ phones, cameras, digital video recorders and other USB

powered devices and accessories. The OPTIMA® Digital 1200 also features integrated ergonomically

designed non-slip DC charging clamps housed in a rear compartment for easy access and storage.

Featuring an LCD battery charging gauge, the OPTIMA® Digital 1200 is the only performance

charger with empty to full status of the battery being charged. The LCD display includes full length

messages for charge mode, status and fault conditions with real time indication of DC voltage

and charging amps during charge modes.

The OPTIMA® Digital 1200 has an innovative pre-charge battery status feature providing charge

level and status of your battery before charging. Designed for the professional, enthusiast and

collector, the Digital 1200 also includes quick set charge modes. In addition, quick set auto

maintainer modes can be facilitated with the charging clamps or the auxiliary maintainer side

port for a hardwired maintainer connection in your vehicle during short or long term storage.

Your OPTIMA® Digital 1200 is for use with all OPTIMA® 12 Volt batteries, in addition to other high

performance 12V AGM (Absorbed Glass Matt), 12V standard Flooded lead-acid and standard

12V AGM batteries. Experience easy operation with our quick set charge selector by battery type

or auto maintainer by connection type. For quick and easy charging of your battery, simply choose

the battery type shown and the OPTIMA® Digital 1200 will do the rest.

Product Overview

Digital 1200 Performance Multi-Stage Charging

Recover deeply discharged batteries, enhance the performance of your battery and extend battery

life. The OPTIMA® Digital 1200 Performance Charger employs the latest in digital, multi-stage

charging. With up to 6 fully automatic modes your Digital 1200 Performance Charger will sequence

through stages 1 through 6 below:

Stage 1: Analyze your battery for the state of charge and quality of connections before charging.

Stage 2: Soft ramp charging-controlled amperage for deeply discharged batteries - when necessary.

Stage 3:Fast charge bulk mode for batteries moderately discharged - also known as

normal battery usage.

Stage 4: Conditioning mode for conditioning your battery with a finish/complete charge.

Stage 5: Auto maintain, float mode for keeping your battery fully charged.

Stage 6:A 30-day storage recondition mode - while your vehicle or battery is in storage

and is being maintained.

Performance tip: A battery in any one state (charged or not charged) can begin

to sulfate and impact battery performance. The OPTIMA

Digital 1200 is designed

to recondition your batteries every 30 days for up to 3 hours in the battery storage

recondition mode. When completed, the auto-maintain mode will resume, while

your battery is fully charged.

Additional peace of mind safety and operation features:

Spark-free connection technology.

Reverse polarity and over temperature protection.

Ambient air temperature compensation during charging - Digitally controls the charger

output in high heat or extreme low temperature conditions.

At-a-glance battery connected and battery fault icons.

Audible fault alarm to bring attention to fault or improper connection conditions.

iPod, iPad and iPhone are trademarks of Apple Inc.

Android is a trademark of Google Inc.

These trademark holders do not sponsor or endorse the OPTIMA® Digital 1200

13 14

Digital 12 00 Digital 12 00

Getting to Know your Charger

Feature Function

1. LCD Battery Charging Gauge LCD display for charging, maintaining, and fault mode indication.

Gauge displays battery charging (fill) rate with charger mode and

fault messages. See pages 21-25.

2. Quick Set Charging Selector Quick and easy selection of charge profiles by battery type.

(Engine starting, deep cycle, auto/marine and motorcycle).

See pages 17 and 22.

3. Quick Set Maintainer and Set maintainer modes by connection type (DC clamps or ring terminal

Pre-Charge Battery Status Selector cable assembly for stored or seasonal use vehicles). See page 23.

4. Non-Slip Carrying Handle Fold away handle ratchets in the up and down positions.

5. AC Power Cord Storage Clip Holds the AC power cord in place free from obstructing the handle.

6. AC Power Cord Wrap Stores AC power cord when not in use.

7. 3 Prong AC Power Plug UL rated 3 prong AC power plug that is properly grounded.

Do not alter.

8. Latching Rear Storage Compartment Stores DC charging cable and clamps when not in use.

9. DC Cable Exits (Left and Right Side) Conveniently close the rear door during charger operation

with cables exiting either the left or right hand side.

10. Push Button LED Work Light Integrated LED in red (+) charging clamp. When the charger is

plugged into AC power you can use this work light in dark conditions

or as a general source of light.

11. Non-Slip DC Charging Clamps Red (+) and gray (-) heavy duty battery clamps.

12. USB Power and Charging Port When the charger is plugged into AC power this USB port is on

and available as indicated by the illuminated green LED. 5 Watt

USB port is compatible with iPad®, iPhone® and can be used with

Android™ phones, other cell phones, digital cameras, and other

USB powered devices.

13. Auxiliary Maintainer Port Use with supplied ring terminal cable assembly for hardwired in

vehicle auto-maintaining of your battery. Green LED will turn on

when this feature is selected.

14. Side Port Protective Cover Protects both the USB port and auxiliary maintainer port.

Getting to Know your Charger

This section of the manual is designed to give you a complete understanding of the features,

functions and operation of your OPTIMA® Digital 1200 12 Volt Performance Charger and Maintainer.

Feature Function

15. Quick Set Charging Prompt Illuminates green prompting user to make a selection.

16. AC Power Illuminates blue when AC power is applied and unit is on.

17. Temperature Compensation On Illuminates green after making a quick set selection as it

monitors the ambient air temperature and digitally controls the

charging process by ambient air temperature.

18.Quick Set Maintainer Prompt Illuminates green prompting user to make a selection.

19. Battery Connected Illuminates green after making a quick set selection.

Check mark LED is on confirming battery is connected

20. Check Battery Fault warning LED will illuminate red only if there is a

connection or battery problem requiring attention in addition

to LCD fault messaging. Charger will “chirp” with an audible tone

letting you know to read the fault message and attend to the battery

or charger.

21. Fill Gauge Empty to full pre-charge status, charge and auto-maintain mode gauge.

22. Mode/Fault Message Center Displays charging, conditioning and auto maintain mode status

and fault condition.

23. Volts DC Display Displays pre-charge status, charging and auto maintain

charger voltage.

24. Amps DC Display Displays charging and auto maintain charger amperage

Getting to Know your Charger

Digital 12 00 Digital 12 00

Getting to Know your Charger

Feature Function

25. OPTIMA® Starting Charge Profile For quick set automatic selection of OPTIMA® RedTop and BlueTop

AGM STARTING batteries or other High Performance starting AGM's.

26. OPTIMA® Deep Cycle Charge Profile For quick set automatic selection of OPTIMA® YellowTop and

BlueTop AGM DEEP CYCLE batteries and/or other High Performance

deep cycle AGM's.

27. (Small) Standard Flooded Charge Profile For quick set selection of standard 12V motorcycle, power sports, tractor

(small) AGM and Flooded batteries. Up to 40 Amp hour rated batteries.

28. (Large) Standard Flooded Charge Profile For quick set selection of standard 12V auto, marine, truck, RV

(large) AGM and Flooded batteries. 40 - 130 Amp hour rated batteries.

29. Maintain Battery by Charging Clamps If your battery is fully charged and you want to automatically

maintain your battery in or out of a vehicle keeping it fully charged.

30. Maintain Battery by Auxiliary Port If your battery is fully charged and you want to automatically

maintain your battery in or out of a vehicle keeping it fully charged.

Ideal method for most existing and all new vehicle “ring terminal”

maintainer cable installations (cable assembly included).

31. LCD Backlight The LCD display will turn off when a battery is fully charged and

is being automatically maintained. To turn off/on the LCD back

light simply touch this button.

32. Pre-Charge Battery Status Prior to charging your battery you may select this function.

ENGINE MUST BE OFF to have the charger identify the state

of charge of your battery before charging.

Charging Battery Types & Approximate Charge Times

The OPTIMA® Digital 1200 12 Volt Performance Charger and Maintainer is designed specifically

for 12 Volt batteries.

Please use the table below to understand your battery type before making a quick

set “battery type charging profile” selection.

CAUTION - IMPORTANT NOTICE: Don’t know your battery type? Look online or call your

local dealer with your battery manufacturer’s name and part number to identify your battery

type before charging. Do not charge 4D, 8D or other high capacity 6, 8 or 12 Volt batteries

typically seen in golf carts as they are typically wired for 24 Volt, 36 Volt or 48 Volt configurations

and have a dedicated / specific charger to be used.

Do not connect or use your OPTIMA® Digital 1200 battery charger to charge dry cell and/or

Lithium Ion batteries that are commonly used with home appliances or power tools. These

batteries may burst and cause injury to persons and property. Do not use with Gel batteries.

NEVER charge a frozen battery.

Read all important safety and cautionary markings on your battery by the manufacturer

and in this manual before using your OPTIMA® Digital 1200 Charger.

Description of Battery Type

OPTIMA® 12 Volt AGM starting batteries

OPTIMA® RedTop and BlueTop

batteries with a dark gray body

Other high performance AGM

starting batteries

OPTIMA® 12 Volt AGM deep cycle batteries

OPTIMA® YellowTop and BlueTop

batteries with a light gray body

Other high performance AGM

deep cycle batteries

Standard 12 Volt Flooded lead-acid

and standard AGM batteries

Flooded (large) auto, marine, truck,

RV batteries with and without caps

AGM (large) auto, marine, truck,

RV batteries

Standard 12 Volt Flooded lead acid

and standard AGM batteries

Flooded (small) motorcycle, tractor,

power sport batteries with and

without caps

AGM (small) motorcycle, tractor,

power sport batteries

Approximate

Amp Hour Rating

40-100 Ah

35-100 Ah

40 to 130 Ah

up to 40 Ah

Battery Type

High Performance

AGM (Absorbed

Glass Mat) starting

batteries

High Performance

AGM (Absorbed

Glass Mat) deep

cycle batteries

Standard Flooded

lead-acid and

AGM (Absorbed

Glass Mat) batteries

(large)

Standard Flooded

and AGM (Absorbed

Glass Mat) batteries

(small)

Approximate

Charge Times

3 to 5 hours at

20 to 40% discharge

6 to 10 hours at 50%

or greater discharge

3 to 5 hours at

20 to 40% discharge

6 to 12 hours at 50%

or greater discharge

3 to 6 hours at

20 to 40% discharge

6 to 12 hours at 50%

or greater discharge

1 to 3 hours at

20 to 40% discharge

5 to 10 hours at 50%

or greater discharge

Quick Set Icon

Profile 1

Engine Starting

Profile 2

Deep Cycle

Profile 3

Auto/Marine

Profile 4

Motorcycle

Digital 12 00

WARNING - FAILURE TO FOLLOW INSTRUCTIONS MAY CAUSE SERIOUS INJURY,

DAMAGE OR EXPLOSION, ALWAYS SHIELD EYES WITH SAFETY GLASSES.

Follow all General and Personal Safety Precautions in this manual and those by the

battery manufacturer.

Follow all the preparing-to-charge steps for out of vehicle battery charging /

maintaining.

For out of vehicle charging or auto maintaining a fully charged battery, please find below a

general illustration of the steps for connecting your charger for operation. General illustration

is for an out of vehicle set up.

1. Connect the red POSITIVE (POS, P, +) cable clamp to the POSITIVE (POS, P, +) post.

2. Connect the black NEGATIVE (NEG, N, -) cable clamp to the NEGATIVE (NEG, N, -) post.

3. Plug the charger into a properly grounded GFCI protected outlet.

Pictured:Typical DC charging clamp connections for a precharge status, charging or just

maintaining a fully charged battery with the DC charging clamps out of vehicle.

Operating Instructions

Easy Set up - Charging w/ DC Clamps out of a Vehicle

Easy Set up - Auxiliary Side Port Maintainer Setup

WARNING - FAILURE TO FOLLOW INSTRUCTIONS MAY CAUSE SERIOUS INJURY,

DAMAGE OR EXPLOSION, ALWAYS SHIELD EYES WITH SAFETY GLASSES.

Follow all General and Personal Safety Precautions in this manual and those by the

battery manufacturer.

Follow all the preparing-to-charge steps for in a vehicle and out of vehicle battery

charging / maintaining.

Pictured: Typical side port hardwired maintainer cable assembly connections for auto-maintaining

a fully charged battery in or out of a vehicle with a hardwired cable connection. Cable supplied.

For in a vehicle auto maintaining (not shown) a fully charged battery please find below the

steps for setting up your charger for the side port hardwired auto-maintainer operation. The

sequence of steps below is for an in a vehicle installation set up for the most common vehicles

(negative chassis ground vehicles).

1. Plug the provided “Direct Connect Maintainer Cable Assembly” into the side port maintainer.

2. Connect the red POSITIVE (POS, P, +) ring terminal to the POSITIVE (POS, P, +) post.

3. Connect the BLACK NEGATIVE (NEG, N, -) ring terminal to the vehicle’s chassis.

Do not connect the black negative (NEG, N, -) cable to metal fuel lines

or anywhere in proximity of the carburator or the battery itself.

4. Plug the charger into a properly grounded GFCI protected outlet.

Note: In the event your vehicle is a POSITIVE (POS, P, +) ground set up then follow the safety

instructions on page 8 for charging a battery in a positive grounded vehicle.

Digital 12 00 Digital 12 00

WARNING - FAILURE TO FOLLOW INSTRUCTIONS MAY CAUSE SERIOUS INJURY,

DAMAGE OR EXPLOSION, ALWAYS SHIELD EYES WITH SAFETY GLASSES.

Follow all General and Personal Safety Precautions in this manual and those by

the battery manufacturer.

Follow all the preparing-to-charge steps for in a vehicle battery charging / maintaining.

For in a vehicle charging or auto maintaining a fully charged battery, please find below the

sequence of steps for in a vehicle charging (negative chassis ground vehicles).

1. Connect the red POSITIVE (POS, P, +) cable clamp to the POSITIVE (POS, P, +) post.

2. Connect the BLACK NEGATIVE (NEG, N, -) cable clamp to the vehicle’s chassis.

Do not connect the black negative (NEG, N, -) cable clamp to metal fuel lines

or anywhere in proximity of the carburetor or the battery itself.

3. Plug the charger into a properly grounded GFCI protected outlet.

Pictured: Typical DC charging clamp connections for a precharge status (with engine off),

charging or just maintaining a fully charged battery with the DC charging clamps in a vehicle.

Note: In the event your vehicle is a POSITIVE (POS, P, +) ground set up then follow the safety

instructions on page 8 for charging a battery in a positive grounded vehicle.

Easy Set up - Charging w/ DC Clamps in a Vehicle

Digital 12 00 Digital 12 00

Quick Set Operations

After connecting to a battery:

With your OPTIMA® Digital 1200 12 Volt Performance Charger set up as outlined in pages 17-19, you

can now make quick and easy selections. With the charger plugged into a GFCI protected 110 VAC

outlet, and properly connected to a battery, the OPTIMA® Digital 1200 will automatically perform a quick

self-test of the display and all LEDs. Following the self-test you will be prompted by the display and the

directional arrows to make a quick set selection. From left to right are the LCD screens you will see:

Note: Self test takes less than 2 minutes. If after 10 minutes no selection is made,

the OPTIMA

Digital 1200 will automatically default to a safe maintainer mode.

Note: It is recommended to make a selection and allow the charger to finish that selection

before making a different selection.

Below is an overview of each function that can be selected.

1. Pre-Charge Battery Status.

Note: Vehicle engine and all charging systems must be off.

This quick and easy feature allows you to understand your battery’s state of charge before charging

it. To use this feature, use the RIGHT SIDE “Maintainer Quick Set Selector” to choose the battery pre-

charge status function. The LCD display will provide the current state of battery in % of charge and

DC volts in the numeric display. Below is a typical sequence of the display during this selection.

Note: If the charger identifies a fault during this process or any quick set process it will

illuminate the “Check Battery” icon on the top of the charger and it will “chirp” with an

audible tone letting you know to read the fault message and attend to the battery or charger.

See pages 24 and 25 for Fault Screens and Troubleshooting steps.

Make a Quick Set Selection Prompt

Display Check

00.0 00.0

Volts DC Amps DC

see manual

100

OPTIMA DISPLAY

CHECK

MAKE A QUICK SET

SELECTION NOW

Deeply Discharged Status;

From here you can make a

Quick Set Charge Selection

for your battery type.

Processing Normal Charge Status

13.4 1.0

Volts DC Amps DC

see manual

100

PRE-CHARGE

BATTERY STATUS

13.4 1.0

Volts DC Amps DC

see manual

100

BATTERY

NORMAL

7.0 1.0

Volts DC Amps DC

see manual

100

DEEP DISCHARGE

SELECT CHARGE

2. Quick Set Charging by Battery Type.

From the LEFT SIDE “Charging Quick Set Selector,” choose the BATTERY TYPE that matches

the battery type descriptions as outlined on page 17 titled: “Charging Battery Types &

Approximate Charge Times.”

After selecting 1 of the 4 battery types the charger will begin its stage 1 “Analyzing Battery”

mode. This mode can take up to 2 minutes to complete while it determines the state of your

battery and check that all connections made are correct.

Upon completing the Stage 1 “Analyzing Battery” mode, the charger will start its multi-stage

charging process checks and will sequence through the illustrated LCD screens highlighted below:

Analyzing Battery Mode (screen not shown)

Charging Battery Mode

Conditioning Battery Mode

Maintaining Battery

30 Day Recondition Mode

Note: If the charger identifies a fault during this process or any quick set process it will

illuminate the “Check Battery” icon on the top of the charger and it will “chirp” with an

audible tone letting you know to read the fault message and attend to the battery or charger.

See pages 24 and 25 for Fault Screens and Troubleshooting steps.

Quick Set Operations

Profile 1

Engine

Starting

Profile 2

Deep Cycle

Profile 3

Auto/Marine

Profile 4

Motorcycle

10.5 10.0

Volts DC Amps DC

see manual

100

CHARGING 12V

OPTIMA BATTERY

14.6 5.5

Volts DC Amps DC

see manual

100

CONDITIONING 12V

OPTIMA BATTERY

13.4 1.0

Volts DC Amps DC

see manual

100

MAINTAINING 12V

OPTIMA BATTERY

13.4 1.0

Volts DC Amps DC

see manual

100

OPTIMA 30 DAY

3 HR RECONDITION

13.4 1.0

Volts DC Amps DC

see manual

100

MAINTAINING 12V

OPTIMA BATTERY

10.5 10.0

Volts DC Amps DC

see manual

100

CHARGING 12V

OPTIMA BATTERY

14.6 5.5

Volts DC Amps DC

see manual

100

CONDITIONING 12V

OPTIMA BATTERY

13.4 1.0

Volts DC Amps DC

see manual

100

MAINTAINING 12V

OPTIMA BATTERY

13.4 1.0

Volts DC Amps DC

see manual

100

OPTIMA 30 DAY

3 HR RECONDITION

13.4 1.0

Volts DC Amps DC

see manual

100

MAINTAINING 12V

OPTIMA BATTERY

10.5 10.0

Volts DC Amps DC

see manual

100

CHARGING 12V

SMALL BATTERY

14.6 5.5

Volts DC Amps DC

see manual

100

CONDITIONING 12V

SMALL BATTERY

13.4 1.0

Volts DC Amps DC

see manual

100

MAINTAINING 12V

SMALL BATTERY

13.4 1.0

Volts DC Amps DC

see manual

100

30 DAY 3 HR

12V RECONDITION

13.4 1.0

Volts DC Amps DC

see manual

100

MAINTAINING 12V

SMALL BATTERY

10.5 10.0

Volts DC Amps DC

see manual

100

CHARGING 12V

LARGE

BATTERY

14.6 5.5

Volts DC Amps DC

see manual

100

CONDITIONING 12V

LARGE

BATTERY

13.4 1.0

Volts DC Amps DC

see manual

100

MAINTAINING 12V

LARGE

BATTERY

13.4 1.0

Volts DC Amps DC

see manual

100

30 DAY 3 HR

12V RECONDITION

13.4 1.0

Volts DC Amps DC

see manual

100

MAINTAINING 12V

LARGE

BATTERY

PERFORMANCE AGMSSTANDARD FLOODED & AGMS

2423

Digital 12 00 Digital 12 00

Quick Set Operations

3. Quick Set Battery Auto-Maintainer by Connection Type.

From the RIGHT SIDE “Maintainer Quick Set Selector” choose a maintainer connection type

that matches your set up as outlined on pages:

Page 18: Easy Set Up - “Charging with DC Clamps out of a Vehicle”

Page 19: Easy Set Up - “Charging with DC Clamps in a Vehicle”

Page 20: Easy Set Up - “Auxiliary Side Port Maintainer Setup” for in or out of vehicle auto-maintaining.

Select the battery maintainer by using the touch button quick sets:

A. “DC Charging Clamps”

B. The “Auxiliary (AUX)” side port maintainer (for hardwired in or out of vehicle connections).

After making a selection the charger will begin its auto-maintain process and will sequence

through the following LCD screens as shown below for the connection type selected:

Note: For short and long term storage the OPTIMA

Digital 1200 will automatically recondition

batteries every 30 days for 3 hours.

Note: If the charger identifies a fault during this process or any quick set process it will

illuminate the “Check Battery” icon on the top of the charger and it will “chirp” with an

audible tone letting you know to read the fault message and attend to the battery or charger.

See pages 24 and 25 for Fault Screens and Troubleshooting steps.

Battery

Maintainer

Plug in On Side

AUX

Maintainer

13.4 1.0

Volts DC Amps DC

see manual

100

MAINTAINING

12V BATTERY

13.4 1.0

Volts DC Amps DC

see manual

100

MAINTAINING

12V BATTERY

13.4 1.0

Volts DC Amps DC

see manual

100

30 DAY 3 HR

12V RECONDITION

13.4 3.0

Volts DC Amps DC

see manual

100

MAINTAINING

12V BATTERY

13.4 1.0

Volts DC Amps DC

see manual

100

MAINTAINING

12V BATTERY

13.4 1.0

Volts DC Amps DC

see manual

100

30 DAY 3 HR

12V RECONDITION

Fault Screens and Trouble Shooting

If at any time a fault is identified by the charger the following will appear:

“Check Battery” icon red LED will illuminate.

The charger will have an audible “chirp” identifying attention is needed.

A fault message will be displayed in the LCD center display

Below are the OPTIMA® Digital 1200 LCD fault screens in addition to basic trouble shooting steps.

Verify both leads from the charger are connected to the battery.

Verify connection type (clamps or ring terminal) is correct.

Battery voltage may be too low to accept a charge. Return

battery to dealer for testing. If battery is under 1.25VDC another

battery may be used in parallel to start the charging process,

then be removed.

Verify aux. ring terminal connector is securely plugged into charger.

see manual

CHECK CONNECTION

OR BATTERY<1.25V

Check Connection or Battery < 1.25V

Reverse Polarity - Wiring Fault

Check connection red postive cable clamp or ring

terminal to positive post.

see manual

REVERSE POLARITY

WIRING FAULT

see manual

CHARGER HI-TEMP

FAULT CONDITION

Charger Hi-Temp - Fault Condition

Ambient temperature and/or unit temperature are too high

to charge at this time.

Charger will automatically resume charging when appropriate.

If recharging a deeply discharged battery it is not uncommon for the

charger to enter the Hi-Temp fault condition in order to protect the

charger and battery. Charger will automatically resume charging in

3 to 15 minutes depending on the ambient temperature and condition

of the battery. Do not block cooling vents on bottom of charger and

locations in the AC coil wrap area and place only on a hard surface.

Digital 12 00 Digital 12 00

Check battery voltage with Pre-Charge Status. If greater

than 12.0 volts, restart charger once. Do not repeat more

than once. If fails again, return battery to dealer for testing.

If less than 12.0 volts, return battery to dealer for testing.

Re-verify battery is a 12 Volt battery versus a 6 Volt battery

or other unsupported voltage.

see manual

UNABLE TO CHARGE

CHECK BATTERY

Unable to Charge - Check Battery

Fault Screens and Trouble Shooting

Other General Trouble Shooting Steps:

Note 1: To clear the charger at any time, unplug the charger and wait until the BLUE AC power

indicator is completely off. For typical negative chassis ground applications, disconnect the

battery by removing the BLACK NEGATIVE (NEG, N, -) cable clamp followed by the RED POSITIVE

(POS, P, +) cable clamp. Re-connect your battery, apply AC power per the guidelines of this

manual and make a quick set selection to re-start the function of your choice.

Note 2: For instances where the charger is properly connected and the AC power cord is plugged

into a properly protected 110 VAC GFCI outlet, there are NO LEDs on and the main center LCD

display is not on, follow these steps:

1. Confirm the GFCI protected outlet has not tripped due to a ground fault.

2. Confirm there is 110 VAC present by plugging in a table lamp or meter.

3. Reset and apply power to resume using the OPTIMA® Digital 1200 Charger.

4. If power is present and there are still no LEDs on and the center display is not working then

follow the customer service return steps on page 27 for warranty or out of warranty service.

Note 3: For instances where LCD backlight is not Illuminated - to save energy, LCD backlight

will turn off after 30 minutes. To toggle backlight off/on, press "LCD Backlight" button.

WARNING - AVOID SERIOUS INJURY OR DEATH FROM FIRE, EXPLOSION OR ELECTRICAL SHOCK.

There are no serviceable or replaceable items inside the charger. DO NOT ATTEMPT SERVICE OR

REPAIR AS THIS IS DANGERIOUS AND CAN CAUSE RISK OF EXPLOSION, ELECTRICAL SHOCK OR

LOSS OF LIFE. THIS WILL ALSO VOID ALL WARRANTY COVERAGE.

see manual

OUT OF RANGE

BATTERY>17V

Out of Range - Battery > 17V

Battery voltage is high. Check to see if there is another

battery connected (remove additional battery). Verify there

is not another charger or maintainer source that is connected

or on. Remove if either is present.

Ensure engine is off. Have a dealer check your battery

and/or charging system.

Storage, Care and Technical Specifications

Store your OPTIMA® Digital 1200 12 Volt Performance Charger and Battery Maintainer in a

dry safe location, and inspect all cables before use. Should the AC power cord, plug or the

DC cables be damaged in any way do not attempt to service and follow the return instructions

in the customer service and warranty section of this manual.

Technical Specifications:

AC Input: 100 to 120 VAC, 60 Hz, 3.5 Amps

DC Output: Up to 14.9 VDC (Clamps & Aux.) Digitally & Temperature Controlled

Charge Mode: Up to 12 Amps (Clamps), up to 4 Amps (Aux.)

Maintain Mode: Up to 4 Amps (Clamps & Aux.)

DC USB Output: 5.0 VDC, up to 1 Amp

Battery Types: AGM and Flooded (Lead Acid) Batteries

- 12V Auto / Marine

- 12V Motorcycle / Power Sports

12V OPTIMA and High Performance AGM Batteries

- Starting AGMs include OPTIMA RedTop & BlueTop

- Dual Purpose AGMs include OPTIMA YellowTop & BlueTop

Cables: 6’ AC and DC Cable, 6’ Maintainer Cable

Size: 10” x 7.5” x 6.5”

Weight: 4.8 lbs

Certified to:

UL 1236

CSA C22.2 No. 107.2

FCC Class B

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause

undesired operation.

OPTIMA Chargers, OPTIMA Batteries, The Ultimate Power Source, Spiralcell Technology, RedTop,

YellowTop and BlueTop are trademarks of Clarios, Inc.

iPod, iPad and iPhone are trademarks of Apple Inc.

Android is a trademark of Google Inc.

Digital 12 00

Technical Support and Warranty

OPTIMA

5757 N. Green Bay Ave.

Milwaukee, WI 53209

888.8OPTIMA (888.867.8462)

www.optimabatteries.com

Product Registration: Please register your purchase at www.optimabatteries.com, at the

"Register your OPTIMA®" link.

OPTIMA® Digital 1200 Technical and Warranty Support

Please DO NOT return your product to the dealer from which it was purchased.

In the event you need technical or warranty support please call OPTIMA® customer service

at 1-888-867-8462 (888-8OPTIMA) between 9am-5pm (CST) Monday through Friday,

or via email at www.optimabatteries.com.

All returns must first be authorized by OPTIMA®. Units returned without an RMA# may be

misplaced or delayed.

LIMITED WARRANTY - OPTIMA® Batteries, Inc. (the “Manufacturer”) warrants this battery

charger (the “product”) for three years from the date of original purchase at retail against

defects in material or workmanship that may occur under normal use and care.

If the product is not free from defects in material or workmanship, manufacturer’s obligation

under this warranty is solely to repair or replace your product with a new or reconditioned product,

at the option of the manufacturer. It is your obligation to forward the product, along with a copy

of the original mechanically-produced (e.g. computer printed) purchase receipt postage prepaid

to the manufacturer or its authorized representative, in order for repair or replacement to occur.

Hand-written receipts will not be accepted. This limited warranty is not transferable.

Manufacturer does not provide any warranty for any accessories used with this product that are

not manufactured by OPTIMA® Batteries and approved for use with this product. This limited

warranty is void if the product is misused, subjected to careless handling, opened, repaired, or

modified by anyone other than manufacturer, or if this product is resold through an unauthorized

retailer. This product is not intended for commercial use, and such use will void your warranty.

Manufacturer makes no other warranties, including but not limited to, express, implied or statutory

warranties, including without limitation, any implied warranty of merchantability or implied warranty

of fitness for a particular purpose. Further, manufacturer shall not be liable for any incidental, special

or consequential damage claims incurred by purchasers, users or others associated with this

product, including, but not limited to, lost profits, revenues, anticipated sales, business opportunities,

goodwill, business interruption and any other injury or damage. Any and all such warranties, other

than the limited warranty included herein, are hereby expressly disclaimed and excluded.

Some states do not allow the exclusion or limitation of incidental or consequential damages

or length of implied warranty, so the above limitations or exclusions may not apply to you.

This warranty gives you specific legal rights and it is possible you may have other rights which

vary from this warranty.

THIS LIMITED WARRANTY IS THE ONLY EXPRESS LIMITED WARRANTY AND THE MANUFACTURER

NEITHER ASSUMES OR AUTHORIZES ANYONE TO ASSUME OR MAKE ANY OTHER OBLIGATION

TOWARDS THE PRODUCT OTHER THAN THIS WARRANTY.

Ye a r

Guide de l’utilisateur

La satisfaction du client est notre priorité!

Veuillez ne pas retourner cet appareil au détaillant ni au concessionnaire pour toute demande d'entretien ou de garantie.

Pour toute assistance technique ou de garantie, veuillez appeler le service à la clientèle d’OPTIMA® au 1-888-

867-8462 (888-8OPTIMA) entre 9h00 et 17h00 (HNC) du lundi au vendredi, ou communiquer par courriel à

l’adresse « [email protected] ». Merci. Service à la clientèle OPTIMA®.

AVERTISSEMENT - Le non respect des instructions peut provoquer une explosion, la cécité

ou d’autres blessures graves. Toujours porter une protection oculaire. Des lunettes de sécurité

doivent être portées lors de travaux avec ou à proximité d’une batterie.

INSTRUCTIONS SÉCURITAIRES IMPORTANTES

VEUILLEZ LIRE ET SAUVEGARDER CES INSTRUCTIONS

Le guide de l’utilisateur du Digital 1200 contient d’importantes instructions pour la sécurité et l’utilisation.

En outre, des avertissements sécuritaires importants sont souvent présents sur les batteries et dans les

manuels de propriétaire de véhicule. Veuillez lire et suivre tous les avertissements, les instructions du

fabricant de la batterie et du véhicule, ainsi que les inscriptions de mise en garde de la batterie que vous

chargez avant de brancher l’alimentation c.a. et d'utiliser le chargeur Digital 1200.

Pour une utilisation avec une alimentation de 110 volts 60 Hz c.a. correspondant aux normes

américaine et canadienne

Numéro de modèle : Digital1200 Numéro de série : Date d’achat :

VEUILLEZ NOTER VOTRE :

Digital 12 0 0

Chargeur-mainteneur de batteries 12 volts

haute performance

Introduction.......................................................................................................30

Instructions importantes concernant la sécurité.............................................31-35

Emplacement du chargeur et précautions de connexion C.C. .............................36

Précautions de batterie se trouve dans le véhicule.......................................................37

Précautions de batterie est à l’extérieur du véhicule...........................................38

Manipulation des batteries.......................................................................................39

Description générale de l’appareil................................................................40-41

Apprendre à connaître votre chargeur..........................................................42-45

Chargement des types de batteries et temps de charge approximatif..................46

Installation facile.........................................................................................47-49

a. Chargement avec les pinces c.c. hors d’un véhicule...............................47

b. Chargement avec les pinces c.c. dans un véhicule.................................48

c. Installation avec le port latéral auxiliaire du mainteneur.............................49

Utilisation du réglage rapide........................................................................50-53

a. Bilan de précharge de la batterie...........................................................50

b. Réglage rapide de chargement par type de batterie..................................51

c. Réglage rapide de maintien automatique de batterie par type de connexion....52

Écrans d’anomalie et dépannage.................................................................53-54

Entreposage, entretien.....................................................................................55

Caractéristiques techniques....................................................................................55

Support technique et garantie...........................................................................56

Table des matières

Digital 12 00 Digital 12 00

Nous vous remercions d’avoir acheté récemment un chargeur-mainteneur haute performance

OPTIMA® Digital 1200 12 volts. OPTIMA® a porté le chargement 12 volts automobile de haute

performance à un degré supérieur de conception et de rendement. Intégrant des technologies

numériques de chargement de pointe, le chargeur Digital 1200 permet un chargement

multiphase, un conditionnement, des modes de maintien et de reconditionnement automatiques

de la batterie associés à des commandes de réglage rapide et un écran d’informations ACL

à la pointe de l’industrie. Le chargeur Digital 1200 est « The Ultimate Power Source™»

(la source de puissance extrême) pour tous vos besoins de chargement et de maintenance

de batterie. Le chargeur de première qualité Digital 1200 charge complètement et maintient

tous types de batteries 12 volts tout en allongeant de manière significative leur durée de vie.

Utilisations multiples :

Pour les applications 12 volts automobile, motocyclette, marine, tracteur, sports motorisés,

véhicules récréatifs et plus.

Avantages de la technologie de chargement du chargeur OPTIMA Digital 1200 :

Chargement contrôlé par microprocesseur et logiciel intégrés.

Modes entièrement automatiques de chargement multiphase haute performance, de

conditionnement, de maintenance et de reconditionnement d’entreposage.

Améliore les performances des batteries OPTIMA® et des autres batteries AGM.

Récupère les batteries profondément déchargées.

Allonge la durée de vie des batteries.

Dispose d’un port auxiliaire latéral compatible avec le câble fourni pour l’entretien des

installations courantes de maintenance des batteries précâblées.

Réglage rapide, modes de maintien d’entreposage par type de connexion ou chargement

par type de batterie sur simple pression.

Affichage sur écran ACL du chargement, du maintien et du mode anomalie.

Port USB pour un chargement et une alimentation pratiques d’appareils et d’accessoires

compatibles USB.

Introduction

3231

Digital 12 00 Digital 12 00

3. Ne jamais fumer près de la batterie ou du moteur et éviter toute étincelle ou flammenue à proximité

de ces derniers.

4. Ne jamais charger une batterie gelée.

5. S’il est nécessaire de retirer la batterie du véhicule pour la charger, toujours débrancher la borne

de mise à la masse en premier. S’assurer que le courant auxaccessoires du véhicule est coupé

afin d’éviter la formation d’un arc.

6. Prendre connaissance des mesures de précaution spécifiées par le fabricant de la batterie, p. ex.,

vérifier s‘il faut enlever les bouchons des cellules lors du chargement de la batterie, et les taux

de chargement recommandés.

7. Si le chargeur comporte un sélecteur de tension de sortie, consulter le manuel del’usager

de la voiture pour déterminer la tension de la batterie et pour s’assurer que latension de

sortie est appropriée. Si le chargeur n’est pas muni d’un sélecteur, ne pas utiliser le

chargeur à moins que la tension de la batterie ne soit identique à la tension de sortie

nominale du chargeur.

8. L’utilisation d’un accessoire non recommandé ou non vendu par OPTIMA® peut entraîner

un risque d'incendie, de choc électrique ou de blessures.

9. Afin de réduire le risque d'endommager la fiche et le cordon d’alimentation, tirer sur

la fiche plutôt que sur le cordon pour déconnecter le chargeur.

10.N’utiliser un cordon prolongateur qu’en cas d’absolue nécessité. L’utilisation d’un

cordon prolongateur inapproprié peut entraîner un risque d'incendie et de choc électrique.

Si un cordon prolongateur doit être utilisé, vérifier que :

a. la fiche du cordon prolongateur comporte le même nombre de broches que la fiche

du chargeur et que les broches sont de mêmes forme et taille;

b.le cordon prolongateur est correctement câblé et en bon état électrique;

c. seul un cordon prolongateur de classe industrielle / à usage industriel homologué UL ou

CSA et mis à la terre est utilisé. Avant l’utilisation, s'assurer que le cordon prolongateur

n'est pas endommagé, que les broches ne sont pas tordues et qu'il ne présente aucune

coupure. En cas d'endommagement, remplacer le cordon prolongateur. Toujours connecter

le cordon prolongateur à la fiche du chargeur en premier. Après avoir connecté le cordon

prolongateur au chargeur, brancher le cordon prolongateur dans une prise 20 V c.a. à

proximité et protégée par un disjoncteur de fuite de terre. Consulter les recommandations

du fabriquant ci-après quant à la dimension appropriée des cordons prolongateurs avec

mise à la terre homologués UL ou CSA.

i. Jusqu’à 15.2 m de longueur, utiliser un cordon prolongateur à 3 fils de calibre 18 AWG.

ii. Entre 15.2 m et 30.5 de longueur, utiliser un cordon prolongateur à 3 fils de calibre 16 AWG.

iii. Entre 30.5 et 45.6 de longueur, utiliser un cordon prolongateur à 3 fils de calibre 14 AWG.

11. Ne pas utiliser le chargeur en cas d'endommagement ou d’une défaillance de l’isolation

protectrice des câbles c.a. et c.c., des pinces de chargement, des porte-fusibles cc. et/ou

des cosses rondes du mainteneur. Renvoyer le chargeur à OPTIMA® pour le faire

réparer/vérifier immédiatement.

12. Ne pas utiliser le chargeur s’il a subi un coup violent, un impact direct, si on l'a laissé

tombé ou s'il est autrement endommagé. Renvoyer le chargeur à OPTIMA® pour le

faire réparer/vérifier immédiatement.

Instructions importantes concernant la sécuritéInstructions importantes concernant la sécurité

CONSERVER CES INSTRUCTIONS

Ce manuel contient des instructions importantes concernant la sécurité et le fonctionnement

pour le Digital 1200 Chargeur et mainteneur be batteries 12V.

AVERTISSEMENT

Pour réduire le risque de blessure pour l’utilisateur ou de dommage à la propriété, l’utilisateur doit

lire et comprendre le manuel d’instructions et tous les avertissements apposés sur le chargeur

et les batteries avant l’utilisation.

AVERTISSEMENT

RISQUE DE MÉLANGE DE GAZ EXPLOSIF. Lire le manuel d’instructions avant d’utiliser le chargeur.

1. Connecter et déconnecter les fils de la batterie uniquement lorsque le cordon d’alimentation

est déconnecté.

2. Lorsqu’une batterie est installée dans un véhicule, connecter d’abord le fil de sortie du chargeur

à la borne de la batterie non mise à la masse - non connectée au châssis de l’automobile-

conformément à la polarité indiquée, puis connecter le fil de polarité opposée au châssis

à distance de la batterie; ne pas connecter au carburateur ni aux tuyaux de carburant.

Déconnecter d’abord le fil du châssis. Pour une batterie non installée dans un véhicule,

se reporter au manuel d'instructions.

3. Ne pas trop charger la batterie – se reporter au Manuel d’instructions.

4. NE PAS fumer, ne pas utiliser d'allumette ni provoquer d’étincelle à proximité de la batterie.

5. Utiliser dans un lieu bien ventilé.

6. Se reporter au manuel de l’utilisateur pour des informations plus détaillées.

AVERTISSEMENT

Cet équipement fonctionne avec des pièces, notamment des commutateurs et des relais, qui ont tendance

à produire des arcs ou des étincelles. Par conséquent, s'il est utilisé dans un garage, choisir un emplacement

ou une zone appropriée ou ne pas l’utiliser à moins de 18 pouces au-dessus du sol.

ATTENTION

Risque de choc électrique. Connecter uniquement à des prises mises à la terre adéquatement.

NE PAS exposer à la pluie ni à la neige.

Si les cordons ou les fils/câbles sont endommagés, renvoyer immédiatement l'appareil au complet

à OPTIMA pour le faire réparer.

ATTENTION

1. ATTENTION - RISQE DE MÉLANGE DE GAZ EXPLOSIF

a. IL EST DANGEREUX DE TRAVAILLER A PROXIMITÉ D’UNE BATTERIE AU PLOMB. LES

BATTERIES PRODUISENT DES GAZ EXPLOSIFS EN SERVICE NORMAL. IL EST AUSSI

IMPORTANT DE TOUJOURS RELIRE LES INSTRUCTIONS AVANT D’UTILISER LE CHARGEUR

ET DE LES SUIVRE À LA LETTRE.

b. Pour réduire le risque d’explosion, lire ces instructions et celles qui figurent sur la batterie.

Lisez attentivement toutes les étiquettes apposées sur les appareils et sur le moteur.

2. Utiliser le chargeur pour charger une batterie au plomb uniquement. Ce chargeur n’est pas

conçu pour alimenter un réseau électrique très basse tension ni pourcharger des piles sèches.

Le fait d’utiliser le chargeur pour charger des piles sèches pourrait entraîner l’éclatement

des piles et causer des blessures ou des dommages.

3433

Digital 12 00 Digital 12 00

Instructions importantes concernant la sécurité

17. PRÉCAUTIONS PERSONNELLES

ATTENTION

a. Prévoir la présence d’une personne dans l’environnement proche ou à portée de voix

qui puisse venir en aide lors d'un travail à proximité d’une batterie au plomb.

b. Veiller à disposer de suffisamment de savon, d’eau et de bicarbonate de soude à portée

de la main en cas de contact de l’acide de la batterie avec la peau, les vêtements ou les yeux.

c. Prévoir une protection vestimentaire, oculaire et des mains adéquate. Éviter de se toucher

les yeux lors du travail à proximité d'une batterie.

d. Si l'acide de batterie entre en contact avec la peau ou les vêtements, laver immédiatement

avec de l'eau et du savon. Si l’acide pénètre dans les yeux, rincer immédiatement et

abondamment avec de l'eau froide pendant 15 minutes au moins et obtenir des soins

médicaux immédiatement.

e. Ne jamais fumer près de la batterie ou du moteur et éviter toute étincelle ou flammenue

à proximité de ces derniers.

f. Faire preuve d’une grande prudence afin de réduire le risque de chute d’un outil métallique

sur la batterie. Une chute d’outil peut provoquer une étincelle ou court-circuiter la batterie

ou tout autre matériel électrique, ce qui peut entraîner une explosion ou un incendie.

g. Enlever tout objet personnel en métal, notamment les bagues, bracelets, colliers, montres

et bijoux lorsqu'on travaille à proximité d'une batterie. Une batterie peut provoquer un

courant de court-circuit suffisamment élevé pour souder une bague ou tout autre objet

métallique, avec pour conséquence des brûlures graves.

h. Utiliser le chargeur pour charger une batterie au PLOMB-ACIDE uniquement. Le chargeur

n’est pas conçu pour alimenter un système électrique basse tension autre que celui d'une

applicationde démarrage de moteur. Ne pas utiliser le chargeur de batterie pour charger des

batteries de piles sèches qui sont couramment utilisées dans les appareils électroménagers.

Ces batteries risquent d’éclater et de provoquer des blessures et des dommages à la propriété.

i. Ne jamais charger une batterie gelée.

j. Tenir toute personne, les enfants et les animaux de compagnie à l'écart des batteries

et du chargeur pendant l'utilisation pour éviter des blessures graves, la mort, un incendie

ou une explosion.

k. Ne pas placer le chargeur dans le compartiment moteur ou près de pièces mobiles.

Éloigner le chargeur de la batterie de toute la longueur des câbles c.c.

l. Consulter le manuel du propriétaire du véhicule.

m. Ne pas utiliser le port latéral auxiliaire du mainteneur de batterie / ensemble câble et

les pinces de chargement c.c. du chargeur en même temps.

Instructions importantes concernant la sécurité

13. Ne pas démonter le chargeur. Un remontage incorrect peut entraîner un risque de choc

électrique ou d'incendie. Si une réparation ou une vérification est nécessaire, communiquer

avec le service à la clientèle d'OPTIMA® en composant le 1-888-867-8462 (888-8OPTIMA)

entre 9 h et 17 h (HNC) du lundi au vendredi, ou par courriel à l’adresse

[email protected]. Toute tentative de vérification, de réparation ou de modification

non autorisée peut entraîner un risque de choc électrique, d'incendie ou d'explosion et

annule la garantie.

14. Pour réduire le risque de choc électrique, débrancher le chargeur de la prise avant tout entreti

15. NE PAS exposer le chargeur à la pluie ni à la neige.

16. INSTRUCTIONS POUR CONNECTION À TERRE ET CORDON D’ALIMENTATION C.A.

a. Le chargeur doit être mis à la terre afin de réduire les risques de choc électrique. Le cordon

d’alimentation du chargeur est muni d’un conducteur de terre et d’une fiche avec mise à

la terre. La fiche doit être branchée dans une prise mise à la terre conformément aux codes

d’électricité en vigueur.

DANGER

Ne modifiezjamais le cordon d’alimentation C.A. ou la fiche du chargeur. Si la fiche ne s’adapte

pas à la prise, faites installer une prise d’alimentation C.A. avec mise à la terre par un électricien

qualifié. Une mauvaise connexion peut entraîner des risques de choc électrique.

b.Ce chargeur fonctionne sur un circuit nominal de 120 V et est muni d’une fiche avec mise

à la terre (voir illustration A). Si aucune prise avec mise à la terre n’est disponible, vous

pouvez utiliser un adaptateur, que vous brancherez dans la prise bipolaire (voir illustration B ).

Une telle installation doit être temporaire. Utilisez l’adaptateur jusqu’à ce qu’une prise

avec mise à la terre soit installée.

DANGER

Avant d’utiliser l’adaptateur tel qu’illustré, assurez-vous que la vis centrale de la plaque murale

est mise à la terre. Le connecteur vert de l’adaptateur doit être relié à une prise correctement

mise à la terre. Au besoin, remplacez la vis de la plaque par une vis plus longue afin de bien

fixer le connecteur à la plaque murale et d’assurer une bonne mise à la terre.

L’utilisation d’un adaptateur est interdite au Canada. Si une prise de courant avec mise à la terre

n’est pas disponible en faire installer une par un électricien qualifié avant d’utiliser cet appareil.

Illustration A

Broche de mise

à la terre

Connecteur de

mise à la terre

Vis métallique

Adaptateur Illustration B

3635

Digital 12 00 Digital 12 00

Instructions importantes concernant la sécurité

18. PRÉPARATION AVANT DE CHARGER UNE BATTERIE

ATTENTION

a. Lorsqu’il est nécessaire de retirer une batterie d’un véhicule pour la charger, vérifier que

le moteur est arrêté et que tous les accessoires dans le véhicule sont éteints, afin de ne

pas provoquer d'arc électrique. Toujours déconnecter en premier la borne négative de

la batterie reliée à la masse.

b. Respecter toutes les mises en garde, tous les avertissements et toutes les instructions

spécifiques du fabricant pendant la charge et les taux de charge recommandés. Ne jamais

charger une batterie qui n'a pas de capuchons à évents de sécurité.

c. S’assurer que la zone autour du chargeur et de la batterie est bien ventilée pendant la

charge de la batterie.

Si l’électrolyte entre en contact avec les yeux, ouvrir les yeux au maximum et rincer

abondamment avec de l'eau fraîche et propre pendant 15 minutes au moins. Obtenir

rapidement des soins médicaux.

En cas d’ingestion d’électrolyte, boire de grandes quantités d’eau ou de lait. NE PAS faire

vomir. Obtenir rapidement des soins médicaux.

Neutraliser avec du bicarbonate de soude tout électrolyte renversé sur un véhicule ou sur

la zone de travail. Après avoir neutralisé, rincer et nettoyer la zone contaminée avec de l'eau.

d. Nettoyage des bornes de la batterie. Faire preuve de prudence pour éviter tout contact

d’un élément corrodé avec les yeux.

e. Dans les batteries noyées dotées de capuchons amovibles, AJOUTER UNIQUEMENT DE

L’EAU DISTILLÉE dans chaque cellule jusqu’à ce que l'électrolyte atteigne les niveaux

spécifiés par le fabricant de la batterie. Ne pas trop remplir. Pour une batterie sans entretien

qui n’est pas dotée de capuchons amovibles, notamment les batteries à soupape, respecter

toutes les instructions du fabricant sur la recharge.

f. Déterminer la tension de la batterie en se reportant au manuel du propriétaire du véhicule

et s’assurer que le chargeur est réglé pour le type correct de batterie 12 V. Consulter la

section « Chargement des types de batteries et temps de charge approximatif ».

g. Ne pas trop charger une batterie en sélectionnant un réglage pour un type de batterie

incorrect ou en essayant de charger une batterie autre qu’une batterie 12 volts telle que

définie par les types de batteries 12 volts spécifiées dans ce manuel.

h. Ne pas utiliser le port latéral auxiliaire du mainteneur de batterie / ensemble câble et les

pinces de chargement c.c. du chargeur en même temps.

Emplacement du chargeur et

précautions de connexion C.C.

19. EMPLACEMENT DU CHARGEUR

ATTENTION

a.Placer le chargeur aussi loin de la batterie que les cables C.C. le permettent.

b.Ne jamais placer le chargeur directement sous la batterie à charger ou au-dessus decette

dernière. Les gaz ou les fluides qui s’échappent de la batterie peuvent entraîner la corrosion

du chargeur ou l’endommager.

c.Ne pas faire fonctionner le chargeur dans un espace clos et/ou ne pas gêner la ventilation.

d.Ne jamais laisser l’acide de la batterie couler sur le chargeur lors de la mesure de la

densité de l’électrolyte ou du remplissage d'une batterie.

e.Ne pas poser une batterie sur un chargeur.

f. Ne pas installer sur ou sur les surfaces combustibles.

20. PRÉCAUTIONS DE CONNEXION C.C.

ATTENTION

a.Mettre les interrupteurs du chargeur hors circuit et retirer le cordon C. A. de la prise avant

de mettre et d’enlever les pinces de cordon C.C. s’assurer que les pinces ne se touchent pas.

b.Fixer les pinces de chargement à la batterie et au châssis comme l’indiquent les illustrations

21 (E), 21 (F) et 22 (b) jusqu'à 22 (d).

La page charge ...

Optima Digital 1200 Manuel utilisateur

Marque: Optima

Modèle: Digital 1200

Catégorie: Chargeurs de batterie

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Optima Digital 1200 User manual

Optima Digital 1200 Manuel utilisateur

Optima Digital 1200 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents