BluStream DA11ABL-WP-EU Mode d'emploi

Taper
Mode d'emploi
DA11ABL-WP-EU QUICK REFERENCE GUIDE
01
Contact: support@blustream.com.au | support@blustream-us.com | support@blustream.co.uk
The DA11ABL-WP-EU is a multi-input / output wall plate to convert Bluetooth and
analogue audio within a digital Dante® networked audio system. The DA11ABL-WP-
EU converts 2 x input channels of Bluetooth, or unbalanced audio to Dante® digital
audio, and 2 x channels of Dante® audio to 2 x output channels of unbalanced audio.
The DA11ABL-WP-EU is a plug & play device that is powered using PoE (Power over
Ethernet), or via 12V power supply, oers support for AES67 RTP audio transport,
and magnetic faceplate design allows for both UK & EU backbox compatibility. The
DA11ABL-WP-EU is the ideal BYOD interface to allow any Bluetooth device to stream
audio wirelessly to a Dante® audio system.
Introduction
DA11ABL-WP-EU
Quick Reference Guide
Dante® network wall plate interface for Bluetooth and analogue L/R audio inputs, and L/R audio outputs
Converts 2ch Bluetooth, or un-balanced audio sources to Dante® audio
Converts 2x Dante® audio channels to un-balanced audio outputs
Adjustable input sensitivity from +24dBu to -28dBV via control soware
Adjustable output gain from +20dBu to -28 dBV via control soware
Supports: 44.1, 48 & 96kHz sample rates @ 16, 24 or 32 Bit
Configurable Dante® device latency (supports 1, 2 or 5ms configurable using Dante® Controller)
Supports AES67 RTP audio transport
Features Class 0 IEEE 802.3af PoE for powering of product from any PoE switch
Supports power via 12V DC adapter (supplied) for when network switch does not support PoE
Magnetic faceplate surround allowing for both UK & EU backbox compatibility
FEATURES:
C
M
Y
CM
MY
CY
CMY
K
DA11ABL-WP-EU_REVA7_QRG_PrintReady.pdf 1 22/02/2023 09:51
DA11ABL-WP-EU QUICK REFERENCE GUIDE
02 www.blustream.com.au | www.blustream-us.com | www.blustream.co.uk
Connections:
1 Power Status Indicator - Illuminates when the devices is powered
on power input
2 Bluetooth Status Indicator - Illuminates when Bluetooth device is
connected
3 ID LED Indicator - Flashes when this device is identified through
Dante® Configurator
4 Analogue Audio Input - 3.5mm stereo jack for unbalanced
analogue audio input
5 Bluetooth Pair Button - Press to make device discoverable for
Bluetooth pairing, press 2 to 3 times to change audio source
selection
6 Micro USB Port - Used for soware control and firmware updates
7 Analogue Audio Output - RCA L / R connector unbalanced
analogue audio output
Front Panel
Rear Panel
1
Connections:
1 Dante® Network Connection (PoE) - RJ45 connection to connect
to network switch
2 Power Port – Use 12V/1A DC adaptor (not included) when PoE is
not available to power device
1
Bluetooth
Bluetooth 5.0 technology allows for 2x simultaneous connections from source audio devices, where the selected
devices audio is received and sent into the Dante network.
To connect a Bluetooth enabled device to the DA11ABL-WP-EU, press the Pair button on there unit, go to the
Bluetooth settings of the source audio device, and enable Bluetooth connectivity. The DA11ABL-WP-EU will appear
in the list of available devices.
2 3
6
7
45
2
C
M
Y
CM
MY
CY
CMY
K
DA11ABL-WP-EU_REVA7_QRG_PrintReady.pdf 2 22/02/2023 09:51
DA11ABL-WP-EU QUICK REFERENCE GUIDE
03
Contact: support@blustream.com.au | support@blustream-us.com | support@blustream.co.uk
Dante® Controller soware is required in order to set up
and configure the DA11ABL-WP-EU as well as control
the Dante® network. Audinate provide extensive training
videos and documentation on their website. This can
be found here: http://www.audinate.com/products/
soware/dante-controller
Upon connecting your DA11ABL-WP-EU to a compatible
network, the Dante® Controller soware should
automatically discover the device. The DA11ABL-WP-
EU will appear in the Dante® Controller with a name
prefixed with “DA11ABL-WP-EU”. On the “Routing”
screen you can create audio routing between Dante®
transmitters and receivers in the system.
Please ensure your PC is on the same network as your
Dante® devices. Dante® is not able to transmit over WiFi,
and it is recommended to hardwire into the Dante®
network. Having multiple network devices enabled
can also confuse the Dante® Controller soware so it is
recommended to disable WiFi during configuration.
Dante® Controller
RevA7_QRG_DA11ABL-WP-EU
Advanced Dante® Settings
It is also possible to change the settings of the
DA11ABL-WP-EU under the “Device Info” screen in
the Dante® Controller soware. To do so, select the
“Device Config” menu.
The sample rate of the DA11ABL-WP-EU can be
adjusted here. Please note: Dante® products can
only transmit or receive audio from other Dante®
products that are set up with the same sample rate.
A mismatch in sample rate may stop audio from
transmitting.
Under the “Device Config” screen we can also adjust
the latency of the DA11ABL-WP-EU from 1, 2 or 5
milliseconds.
By default the DA11ABL-WP-EU is shipped with
its network settings set to obtain an IP address
automatically. This means that if a DHCP server is
present on your network, it will provide the DA11ABL-
WP-EU with an IP address. If no DHCP server is
present then the DA11ABL-WP-EU will receive a
default IP address in the 169.254.xxx.xxx range.
To change the IP address of the DA11ABL-WP-EU, you
must enter the “Network Config” menu in the “Device
Info” screen of the Dante® Controller soware.
C
M
Y
CM
MY
CY
CMY
K
DA11ABL-WP-EU_REVA7_QRG_PrintReady.pdf 3 22/02/2023 09:51
DA11ABL-WP-EU QUICK REFERENCE GUIDE
04 www.blustream.com.au | www.blustream-us.com | www.blustream.co.uk
Specifications
Audio Input Connectors: 1 x Analogue Le / Right audio (3.5mm stereo jack)
Audio Output Connectors: 2 x Analogue RCA (Le / Right)
Network Connectors: 1 x PoE Dante® Ethernet Connection (RJ45)
Bluetooth: Bluetooth V5.0 - SBC / MP3 / AAC / APT-X / APTX-LL / APTX-HD, 44.1K-48KHz 16 / 24Bit
Configuration Switches: 1 x Push button (connect / selection)
Firmware Upgrade: 1 x Micro-USB UART port
Module Dimensions (W x H x D): 74mm x 74mm x 50mm (without faceplate)
Faceplate Dimensions (W x H x D): 85mm x 85mm x 5mm
Cut Out Dimensions (W x H x D): 52mm x 55mm x 38mm
Mounting Hole Spacing: UK 60mm CTC, EU 60mm CTC
Backbox Requirements: UK single gang backbox / EU single gang backbox
Shipping Weight: 0.3kg
Operating Temperature: 32°F to 104°F (0°C to 40°C)
Storage Temperature: - 4°F to 140°F (- 20°C to 60°C)
Power Supply: Class 1 IEEE 802.3af POE PD or 12V/1A DC, 2-Pin Phoenix connector
Package Contents
1 x DA11ABL-WP-EU
1 x Magnetic Faceplate
1 x Quick Reference Guide
Acknowledgements
Dante® is a registered trademark of
Audinate Pty Ltd.
FCC NOTICE
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION - changes or modifications not expressly approved by the party
responsible for compliance could void the users authority to operate the
equipment.
CANADA, INDUSTRY CANADA (IC) NOTICES
This Class B digital apparatus complies with Canadian ICES-003.Operation
is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
CORRECT DISPOSAL OF THIS PRODUCT
This marking indicates that this product should not be disposed with
other household wastes. To prevent possible harm to the environment
or human health from uncontrolled waste disposal, recycle it responsibly
to promote the sustainable reuse of material resources. To return your
used device, please use the return and collection systems or contact the
retailer where the product was purchased. They can take this product for
environmentally safe recycling.
RF EXP OSURE
To maintain compliance with FCC’s RF Exposure guidelines, This
equipment should be installed and operated with minimum distance
between 20cm the radiator your body: Use only the supplied antenna.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
CANADA, INDUSTRY CANADA (IC) NOTICES
This device contains licence-exempt transmitter(s)/receiver(s) that
comply with Innovation, Science and Economic Development
Canada’s licence-exempt RSS(s). Operation is subject to the following
two conditions:
This device may not cause interference.
This device must accept any interference, including interference that
may cause undesired operation of the device.
This equipment should be installed and operated with minimum
distance 20cm between the radiator and your body.
L’émetteur/récepteur exempt de licence contenu dans le présent
appareil est conforme aux CNR d’Innovation, Sciences et
Développement économique Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes :
L’appareil ne doit pas produire de brouillage;
L’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
Cet équipement doit être installé et utilisé avec une distance minimale
de 20 cm entre le radiateur et votre corps.
Certifications
C
M
Y
CM
MY
CY
CMY
K
DA11ABL-WP-EU_REVA7_QRG_PrintReady.pdf 4 22/02/2023 09:51
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

BluStream DA11ABL-WP-EU Mode d'emploi

Taper
Mode d'emploi

dans d''autres langues