Hitachi M 12SA2 Manuel utilisateur

Marque: Hitachi

Modèle: M 12SA2

Catégorie: Outils électroportatifs

Taper: Manuel utilisateur

Ce manuel convient également à

INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI

AVERTISSEMENT

Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner la

mort ou de sérieuses blessures corporelles !

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce

produit. Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil

motorisé. Garder ce mode d’emploi à la disponibilité des autres utilisateurs et

propriétaires avant qu’ils utilisent l’outil motorisé. Ce mode d’emploi doit être conservé

dans un endroit sûr.

SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL

WARNING

IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily

injury!

This manual contains important information about product safety. Please read and

understand this manual BEFORE operating the power tool. Please keep this manual

available for other users and owners before they use the power tool. This manual should

be stored in safe place.

INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES

ADVERTENCIA

¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede resultar

en lesiones de gravedad o la muerte!

Este manual contiene información importante sobre la seguridad del producto. Lea y

comprenda este manual ANTES de utilizar la herramienta eléctrica. Guarde este manual

para que puedan leerlo otras personas antes de utilizar la herramienta eléctrica. Este

manual debe ser guardado en un lugar seguro.

M 12V2 • M 12SA2

M12V2

Model Router

Modèle Détoureuse

Modelo Fresadora

English Page

IMPORTANT SAFETY INFORMATION ................ 3

MEANINGS OF SIGNAL WORDS ........................ 3

SAFETY ...................................................................... 4

GENERAL SAFETY RULES ................................... 4

SPECIFIC SAFETY RULES AND SYMBOLS......... 6

DOUBLE INSULATION FOR SAFER

OPERATION ................................................... 7

USE OF EXTENSION CORD ................................. 8

FUNCTIONAL DESCRIPTION.................................... 9

NAME OF PARTS .................................................. 9

SPECIFICATIONS .................................................. 9

Page

ASSEMBLY AND OPERATION ............................... 10

APPLICATIONS ................................................... 10

PRIOR TO OPERATION ....................................... 10

INSTALLING AND REMOVING BITS ................. 11

HOW TO USE THE ROOTER............................... 12

USING THE OPTIONAL ACCESSORIES ............ 16

MAINTENANCE AND INSPECTION ....................... 17

ACCESSORIES ......................................................... 18

STANDARD ACCESSORIES ............................... 18

OPTIONAL ACCESSORIES ................................. 19

PARTS LIST.............................................................. 58

TABLE DES MATIERES

Français Page

INFORMATIONS IMPORTANTES

DE SÉCURITÉ ............................................... 20

SIGNIFICATION DES MOTS

D’AVERTISSEMENT .................................... 20

SECURITE ................................................................ 21

CONSIGNES DE SÉCURITÉ GÉNÉRALES

............. 21

REGLES DE SECURITE SPECIFIQUES

ET SYMBOLES ............................................. 23

DOUBLE ISOLATION POUR UN

FONCTIONNEMENT PLUS SUR ................. 25

UTILISATION D’UN CORDON DE RALLONGE ...

DESCRIPTION FONCTIONNELLE ........................... 27

NOM DES PARTIES ............................................ 27

SPECIFICATIONS ................................................ 27

Page

ASSEMBLAGE ET FONCTIONNEMENT ................ 28

APPLICATIONS ................................................... 28

AVANT L’UTILISATION ...................................... 28

INSTALLATION ET RETRAIT DE LA MECHE..... 29

UTILISATION DE DETOUREUSE ....................... 29

UTILISATION DES ACCESSOIRES

EN OPTION................................................... 35

ENTRETIEN ET INSPECTION .................................. 36

ACCESSOIRES ......................................................... 37

ACCESSOIRES STANDARD ............................... 37

ACCESSOIRES SUR OPTION ............................. 38

LISTE DES PIÈCES................................................... 58

ÍNDICE

Español Página

INFORMACIÓN IMPORTANTE

SOBRE SEGURIDAD .................................... 39

SIGNIFICADO DE LAS PALABRAS

DE SEÑALIZACIÓN ...................................... 39

SEGURIDAD............................................................. 40

NORMAS GENERALES DE SEGURIDAD........... 40

NORMAS Y SÍMBOLOS

ESPECÍFICOS DE SEGURIDAD ................... 42

AISLAMIENTO DOBLE PARA OFRECER

UNA OPERACIÓN MÁS SEGURA .............. 44

UTILIZACIÓN DE UN CABLE PROLONGADOR...

DESCRIPCIÓN FUNCIONAL.................................... 46

NOMENCLATURA............................................... 46

ESPECIFICACIONES............................................ 46

Página

MONTAJE Y OPERACIÓN ...................................... 47

APLICACIONES ................................................... 47

ANTES DE LA OPERACIÓN ................................ 47

INSTALACIÓN Y EXTRACCIÓN DE

LAS BROCAS ............................................... 48

CÓMO USAR LA FRESADORA .......................... 49

UTILIZACION DE LOS ACCESORIOS

OPCIONALES ............................................... 54

MANTENIMIENTO E INSPECCIÓN ........................ 55

ACCESORIOS........................................................... 56

ACCESORIOS ESTÁNDAR ................................. 56

ACCESORIOS OPCIONALES .............................. 57

LISTA DE PIEZAS .................................................... 58

CONTENTS

English

IMPORTANT SAFETY INFORMATION

Read and understand all of the safety precautions, warnings and operating instructions in

the Instruction Manual before operating or maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused by the

failure to observe basic safety rules or precautions. An accident can often be avoided by

recognizing a potentially hazardous situation before it occurs, and by observing appropriate

safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual

and in the sections which contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identified by

WARNINGS on the power tool and in this Instruction Manual.

NEVER use this power tool in a manner that has not been specifically recommended by

HITACHI.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could result in

death or serious injury.

CAUTION indicates a potentially hazardous situations which, if not avoided, may result in

minor or moderate injury, or may cause machine damage.

NOTE emphasizes essential information.

English

SAFETY

GENERAL SAFETY RULES

WARNING: Read all instructions

Failure to follow all instructions listed below may result in electric shock,

fire and/or serious injury.

The term “power tool” in all of the warnings listed below refers to your

mains-operated (corded) power tool or battery-operated (cordless)

power tool.

SAVE THESE INSTRUCTIONS

1) Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases or dust.

Power tools create sparks which may ignite the dust of fumes.

c) Keep children and bystanders away while operating a power tool.

Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way.

Do not use any adapter plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators,

ranges and refrigerators.

There is an increased risk of electric shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the

power tool.

Keep cord away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for outdoor

use.

Use of a cord suitable for outdoor use reduces the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use common sense when operating a

power tool.

Do not use a power tool while you are tired or under the influence of drugs, alcohol

or medication.

A moment of inattention while operating power tools may result in serious personal

injury.

English

b) Use safety equipment. Always wear eye protection.

Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing

protection used for appropriate conditions will reduce personal injuries.

c) Avoid accidental starting. Ensure the switch is in the off position before plugging

in.

Carrying power tools with your finger on the switch or plugging in power tools that

have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on.

A wrench or a key left attached to a rotating part of the power tool may result in

personal injury.

e) Do not overreach. Keep proper footing and balance at all times.

This enables better control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing

and gloves away from moving parts.

Loose clothes, jewellery or long hair can be caught in moving parts.

g) If devices are provided for the connection of dust extraction and collection facilities,

ensure these are connected and properly used.

Use of these devices can reduce dust-related hazards.

4) Power tool use and care

a) Do not force the power tool. Use the correct power tool for your application.

The correct power tool will do the job better and safer at the rate for which it was

designed.

b) Do not use the power tool if the switch does not turn it on and off.

Any power tool that cannot be controlled with the switch is dangerous and must be

repaired.

c) Disconnect the plug from the power source and/or the battery pack from the power

toll before making any adjustments, changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of starting the power tool

accidentally.

d) Store idle power tools out of the reach of children and do not allow persons

unfamiliar with the power tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts, breakage

of parts and any other condition that may affect the power tools operation.

If damaged, have the power tool repaired before use.

Many accidents are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp cutting edges are less likely to bind

and are easier to control.

g) Use the power tool, accessories and tool bits etc., in accordance with these

instructions and in the manner intended for the particular type of power tool,

taking into account the working conditions and the work to be performed.

Use of the power tool for operations different from intended could result in a

hazardous situation.

English

4. Handle the bits very carefully.

5. Check the bit carefully for cracks or damage before operation. Replace cracked or

damaged bit immediately.

6. Avoid cutting nails. Inspect for and remove all nails from the workpiece before

operation.

7. Hold the tool firmly with both hands.

8. Keep hands away from rotating parts.

9. Make sure the bit is not contacting the workpiece before the switch is turned on.

10. Before using the tool on an actual workpiece, let it run for a while. Watch for vibration

or wobbling that could indicate improperly installed bit.

11. Be careful of the bit rotating direction and the feed direction.

12. Do not leave the tool running. Operate the tool only when hand-held.

13. Always switch off and wait for the bit to come to a complete stop before removing the

tool from workpiece.

14. Do not touch the bit immediately after operation: it may be extremely hot and could

burn your skin.

15. Always lead the power supply cord away from the tool towards the rear.

16. After changing the bits or making any adjustments, make sure the collet nut and any

other adjustment devices are securely tightened.

Loose adjustment device can unexpectedly shift, causing loss of control, loose rotating

components will be violently thrown.

5) Service

a) Have your power tool serviced by a qualified repair person using only identical

replacement parts.

This will ensure that the safety of the power tool is maintained.

–WARNING– To reduce the risk of injury, user must read instruction manual.

SPECIFIC SAFETY RULES AND SYMBOLS

1. Hold tools by insulated gripping surfaces when performing an operation where the

cutting tool may contact hidden wiring or its own cord.

Contact with a “live” wire will make exposed metal parts of the tool “live” and shock

the operator.

2. Use clamps or another practical way to secure and support the workpiece to a stable

platform.

Holding the work by hand or against your body leaves it unstable and may lead to loss

of control.

3. ALWAYS wear ear protectors when using the tool for extended periods.

Prolonged exposure to high intensity noise can cause hearing loss.

English

17. ALWAYS wear eye protection that meets the requirement of the latest revision of ANSI

Standard Z87.1.

18. Definitions for symbols used on this tool

V ............ volts

Hz ..........hertz

A............amperes

no..........no load speed

W...........watt

..........Class II Construction

---/min ...revolutions or reciprocation per minute

..........Alternating current

DOUBLE INSULATION FOR SAFER OPERATION

To ensure safer operation of this power tool, HITACHI has adopted a double insulation

design. “Double insulation” means that two physically separated insulation systems have

been used to insulate the electrically conductive materials connected to the power supply

from the outer frame handled by the operator. Therefore, either the symbol “ ” or the

words “Double insulation” appear on the power tool or on the nameplate.

Although this system has no external grounding, you must still follow the normal electrical

safety precautions given in this Instruction Manual, including not using the power tool in

wet environments.

To keep the double insulation system effective, follow these precautions:

䡬Only HITACHI AUTHORIZED SERVICE CENTER should disassemble or assemble this

power tool, and only genuine HITACHI replacement parts should be installed.

䡬Clean the exterior of the power tool only with a soft cloth moistened with soapy water,

and dry thoroughly.

Never use solvents, gasoline or thinners on plastic components; otherwise the plastic

may dissolve.

English

USE OF EXTENSION CORD

Make sure your extension cord is in good condition. When using an extension cord, be sure

to use one heavy enough to carry the current your product will draw.

An undersized cord will cause a drop in line voltage resulting in loss of power and

overheating. Table shows the correct size to use depending on cord length and nameplate

ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the

heavier the cord.

MINIMUM GAGE FOR CORD SETS

Total Length of Cord in Feet (Meter)

0 – 25 26 – 50 51 – 100 101 – 150

(0 – 7.6) (7.9 – 15.2) (15.5 – 30.5) (30.8 – 45.7)

Ampere Rating AWG

More Not More

Than Than

0 – 6 18 161614

6 – 10 18 16 14 12

10 – 12 16 16 14 12

12 – 16 14 12 Not Recommended

WARNING: Avoid electrical shock hazard. Never use this tool with a damaged or

frayed electrical cord or extension cord.

Inspect all electrical cords regularly. Never use in or near water or in

any environment where electric shock is possible.

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO

OTHER USERS

AND

OWNERS OF THIS TOOL!

English

FUNCTIONAL DESCRIPTION

NOTE:

The information contained in this Instruction Manual is designed to assist you in the

safe operation and maintenance of the power tool.

NEVER operate, or attempt any maintenance on the tool unless you have first read and

understood all safety instructions contained in this manual.

Some illustrations in this Instruction Manual may show details or attachments that differ

from those on your own power tool.

NAME OF PARTS

Fig. 1-1

Stopper pole

Scale

Pole lock knob

Stopper block

Base

Sub base

Head cover

Lock

lever

Knob

Fine adjustment

knob

Quick

adjustment

lever

Threaded

column

Housing

Lever

Dial

Handle

End bracket

Lock pin

Collet chuck

Fig. 1-2

SPECIFICATIONS

Model M12V2 M12SA2

Motor Single Phase, Series Commutator Motor

Power source Single Phase 120V AC 60 Hz

Collet chuck capacity 1/2” (12.7 mm), 1/4” (6.35 mm)

Main Body Stroke 2-9/16" (65mm)

Current 15 A

No-load speed 8,000/min – 22,000/min 22,000/min

Weight (without cord) 13.9 lbs (6.3 kg) 13.7 lbs (6.2 kg)

English

ASSEMBLY AND OPERATION

APPLICATIONS

䡬Woodworking jobs centered on grooving and beveling.

For example, grooving beveling, cutting, copying, engraving, shape cutting,

combinations and others.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms to the power source requirements

specified on the product nameplate.

2. Power switch

Ensure that the switch is in the OFF position. If the plug is connected to a receptacle

while the switch is in the ON position, the power tool will start operating immediately

and can cause serious injury.

3. Extension cord

When the work area is far away from the power source, use an extension cord of

sufficient thickness and rated capacity. The extension cord should be kept as short as

practicable.

WARNING:

Damaged cord must be replaced or repaired.

4. Check the receptacle

If the receptacle only loosely accepts the plug, the receptacle must be repaired. Contact

a licensed electrician to make appropriate repairs.

If such a fautly receptacle is used, it may cause overheating, resulting in a serious

hazard.

5. Confirming condition of the environment

Confirm that the work site is placed under appropriate conditions conforming to

prescribed precautions.

English

INSTALLING AND REMOVING BITS

WARNING: Be sure to switch power OFF and disconnect the plug from the

receptacle to avoid serious trouble.

1. Installing bits

(1) Clean and insert shank of bit into the collet

chunk until shank bottoms, then back it out

approximately 1/16” (approx. 2 mm).

(2) With the bit inserted and pressing the lock

pin holding the armature shaft, use the 23

mm wrench to firmly tighten the collet chuck

in a clockwise direction (viewed from under

the router). (Fig. 2)

(3) When using the 1/4” diameter shank bit,

replace the equipped collet chuck with the

one for 1/4” diameter shank bit which is

provided as the standard accessory.

CAUTION:

䢇Ensure that the collet chuck is firmly tightened after inserting a bit. Failure to do so

will result in damage to the collet chuck.

䢇Ensure that the lock pin is not inserted into the armature shaft after tightening the

collet chuck. Failure to do so will result in damage to the collet chuck, lock pin and

armature shaft.

2. Removing bits

When removing the bits, do so by following the steps for installing bits in reverse

order.

CAUTION:

䢇Ensure that the lock pin is not inserted into the armature shaft after tightening a bit.

Failure to do so will result in damage to the collet chuck, lock pin and armature shaft.

Lock pin Wrench

Loosen

Fig. 2

Tighten

English

HOW TO USE THE ROUTER

1. Adjusting depth of cut

(1) Place the tool on a flat wood surface.

(2) Turn the quick adjustment lever in a

counterclockwise direction until the quick

adjustment lever stops. (Fig. 4)

(3) Turn the stopper block so that section to

which the cutting depth setting screw on a

stopper block is not attached comes to the

bottom of the stopper pole. Loosen pole lock

knob allowing the stopper pole to contact

with stopper block.

(4) Loosen the lock lever and press the tool

body until the bit just touches the flat

surface. Tighten the lock lever at this point.

(Fig. 5)

(5) Tighten pole lock knob. Align the depth

indicator with the “0” graduation of scale.

(6) Loosen pole lock knob, and raise until

indicator aligns with the graduation

representing the desired cutting depth.

Tighten pole lock knob.

(7) Loosen the lock lever and press the tool

body down until the stopper block to obtain

the desired cutting depth.

Your router allows you to finely adjust depth of cut.

(1) Attach the accessory knob to fine

adjustment knob. (Fig. 6)

(2) Turn the quick adjustment lever in a

clockwise direction until the quick

adjustment lever stops with the stopper

screw. (Fig. 7)

If the quick adjustment lever does not stop

with the stopper screw, the bolt screw is not

properly fitted.

If this occurs, slightly loosen the lock lever

and press down on the unit (router) hard

from the top and turn the quick adjustment

lever again after properly fitting the bolt

screw.

(3) The depth of cut can be adjusted when the

lock lever is loosened, by turning the fine

adjustment knob. Turning the fine

adjustment knob counterclockwise results

in a shallower cut, whereas turning it

clockwise results in a deeper cut.

Fig. 3

Stopper pole

Scale

Quick

adjustment

lever

Stopper

block

Depth

indicator

Pole lock

knob

Quick adjustment

lever

Fig. 4

Fig. 5

Loosen the

lock lever

Fig. 6

Knob

Fine

adjustment

knob

English

CAUTION:

Ensure that the lock lever is tightened after

finely adjusting depth of cut. Failure to do

so will result in damage to the quick

adjustment lever.

2. Stopper block (Fig. 8)

The 2 cut-depth setting screws attached to

the stopper block can be adjusted to

simultaneously set 3 different cutting depth.

Use a wrench to tighten the nuts so that the

cut-depth setting screws do not come loose

at this time.

3. Guiding the router

WARNING: Be sure to switch power

OFF and disconnect the

plug from the receptacle to

avoid serious trouble.

(1) Template guide adapter

1Loosen the 2 template guide adapter screws,

so that the template guide adapter can be

moved. (Fig. 9)

2Insert the centering gauge through the hole

in the template guide adapter and into the

collet chuck. (Fig. 10)

3Tighten the collet chuck by hand.

4Tighten the template guide adapter screws,

and pull out the centering gauge.

(2) Template guide

Use the template guide when employing a

template for producing a large quantity of

identically shaped products. (Fig. 11)

As shown in Fig. 12, to install insert template

guide in center hole in template guide

adapter (A) with 2 accessory screws.

If you are using a template guide adapter

(B), it is possible to use template guides

produced by other firms. Attach template

guides made by other firms to the template

guide adapter (B).

A template is a profiling mold made of

plywood or thin lumber. When making a

template, pay particular attention to the

matters described below and illustrated in

Fig. 13.

Fig. 7

Quick adjustment lever

Fig. 8

Cut depth

setting screw

Fig. 9

Template guide

adapter

Screw

Centering gauge

Collet chuck

Fig. 10

Template guide

adapter

Fig. 11

English

When using the router along the interior

plane of the template, the dimensions of the

finished product will be less than the

dimensions of the template by an amount

equal to dimension “A”, the difference

between the radius of the template guide

and the radius of the bit. The reverse is true

when using the router along the exterior of

the template.

(3) Straight guide (Fig.14)

Use straight guide for chamfering and

groove cutting along the materials side.

1Insert the guide bar into the hole in the bar

holder, then lightly tighten the 2 wing bolts

(B) on top of the bar holder.

2Insert the guide bar into the hole in the base,

then firmly tighten the wing bolts (A)

(standard accessories).

3Make minute adjustments of the dimensions

between the bit and the guide surface with

the feed screw, then firmly tighten the 2

wing bolts (B) on top of the bar holder and

the wing bolt (C) that secures the straight

guide.

4As shown in Fig. 15, securely attach the

bottom of the base to processed surface of

the materials. Feed the router while keeping

the guide plane on the surface of the

materials.

(4) Dust guide and dust guide adapter (Fig. 16)

Your router is equipped with a dust guide

and a dust guide adapter.

1Match the 2 grooves on the base and insert

the 2 dust guide tabs in holes located in the

base side from the top. Tighten the dust

guide with a screw.

The dust guide diverts cutting debris away

from the operator and directs the discharge

in a consistent direction.

2By fitting the dust guide adapter into the

dust guide cutting debris discharge vent, the

dust extractor can be attached.

4. Adjusting the rotation speed (Model

M12V2 only)

The M12V2 has an electronic control system

that allows stepless rpm changes. As shown

in Fig. 17, dial position “1” is for minimum

speed, and position “6” for maximum

speed.

Fig. 12

Template guide

adapter

Screw

Template

guide

Wing bolt (C)

Guide bar

Straight

guide Feed

screw

Guide plane

Wing bolt (B)

Wing

bolt (A)

Bar holder

Fig. 14

Fig. 15

Fig. 13

Bit

Template

Guide Template

English

5. Removing the spring

The springs within the column of the router

can be removed. Doing so will eliminate

spring resistance and allows easy

adjustment of cutting depth when attaching

the router stand.

(1) Loosen the 4 sub base screws, and remove

the sub base.

(2) Loosen the stopper bolt and remove it, so

the spring can be removed. (Fig. 18)

WARNING:

Remove the stopper bolt with the main unit

(router) fixed at its maximum height.

Removing the stopper bolt with the unit in

a shortened condition may cause the

stopper bolt and spring to be discharged

and cause injury.

6. Cutting

WARNING:

䢇Wear eye protection when operating this

tool.

䢇Keep your hands, face and other body parts

away from the bits and any other rotating

parts, while operating the tool.

(1) As shown in Fig. 19, remove the bit from

the work pieces and press the switch lever

up to the ON position. Do not start cutting

operation until the bit has reached full

rotating speed.

(2) The bit rotates clockwise (arrow direction

indicated on the base). To obtain maximum

cutting effectiveness, feed the router in

conformance with the feed directions shown

in Fig. 20.

NOTE:

If a worn bit is used to make deep grooves,

a high pitched cutting noise may be

produced.

Replacing the worn bit with a new one will

eliminate the high pitched noise.

Fig. 16

Dust guide

adapter

Tab

Screw

Dust guide

Tab

Stopper bolt

Fig. 20

Router feed

Rotation of bit

Router feed

Workpiece

Dial

Fig. 17

Fig. 19

Separate

Fig. 18

Spring

English

USING THE OPTIONAL ACCESSORIES

Trimmer Guide

Use the trimmer guide for chamfering.

As shown in Fig. 21 use the wing bolt to

mount and secure the trimmer guide on the

bar holder.

Use the two wing bolts to align the trimmer

guide in the desired position, and use it as

shown in Fig. 22.

NOTE:

䢇Moving the tool forward fast may cause a poor quality of cut, or damage to the bit or

motor. Moving the tool forward too slowly may burn and mar the cut.

The proper feed rate will depend on the bit size, the kind of workpiece and depth of cut.

Before beginning the cut on the actual workpiece, it is advisable to make a sample cut

on a piece of scrap lumber. This will show exactly how the cut will look as well as

enable you to check dimensions.

䢇Abnormalities and overloads will trigger the overload protector, and stop operation.

Remove the load immediately, and turn the power off, then on. The rotation speed

should return to normal.

䢇Do not use a power generator as the power source. It may cause the rotation speed to

fluctuate.

䢇When using the straight guide, be sure to install it on the right side in the feed direction.

This will help to keep it flush with the side of the workpiece.

Fig. 22

Trimmer guide

Wing bolt

Fig. 21

Bar holder

English

MAINTENANCE AND INSPECTION

WARNING: Be sure to switch power OFF and disconnect the plug from the

receptacle during maintenance and inspection.

1. Inspecting the screws

Regularly inspect all screws and ensure that they are fully tightened. Should any of the

screws be loosened, retighten them immediately.

WARNING: Using this router with loosened screws is extremely dangerous.

2. Maintenance of the motor

The motor unit winding is the very “heart” of the power tool. Exercise due

care to ensure the winding does not become damaged and/or wet with oil or

water.

3. Service and repairs

All quality power tools will eventually require servicing or replacement of parts because

of wear from normal use. To assure that only authorized replacement parts will be

used, all service and repairs must be performed by a HITACHI AUTHORIZED SERVICE

CENTER, ONLY.

4. Service parts list

A: Item No.

B: Code No.

C: No. Used

D: Remarks

CAUTION: Repair, modification and inspection of Hitachi Power Tools must be carried

out by a Hitachi Authorized Service Center.

This Parts List will be helpful if presented with the tool to the Hitachi

Authorized Service Center when requesting repair or other maintenance.

In the operation and maintenance of power tools, the safety regulations

and standards prescribed in each country must be observed.

MODIFICATIONS:

Hitachi Power Tools are constantly being improved and modified to incorporate the

latest technological advancements.

Accordingly, some parts (i.e. code numbers and/or design) may be changed without

prior notice.

English

ACCESSORIES

WARNING: ALWAYS use Only authorized HITACHI replacement parts and

accessories. NEVER use replacement parts or accessories which are

not intended for use with this tool. Contact HITACHI if you are not sure

whether it is safe to use a particular replacement part or accessory

with your tool. The use of any other attachment or accessory can be

dangerous and could cause injury or mechanical damage.

NOTE:

Accessories are subject to change without any obligation on the part of the HITACHI.

STANDARD ACCESSORIES

(1) 1/4” Collet Chuck (Code No. 323-293)..............................................................................1

(2) Template Guide Adapter (A) (attaches to the router) (Code No. 325-211) ................... 1

(3) Template Guide Adapter (B) (Code No. 325-224) ...........................................................1

(4) Template Guide (Code No. 956-790)................................................................................1

(5) Centering Gauge (Code No. 325-223) ..............................................................................1

(6) Dust Guide (Code No. 325-210) ........................................................................................1

(7) Dust Guide Adapter (Code No. 325-215) .........................................................................1

(8) Bar Holder (Code No. 325-217).........................................................................................1

Straight Guide (Code No. 956-797) ..................................................................................1

Feed Screw (Code No. 956-793) .......................................................................................1

Wing Bolt (Code No. 949-394) ..........................................................................................1

(9) Guide Bar (Code No. 325-216) ..........................................................................................2

(10)Knob (Code No. 325-214) ..................................................................................................1

(11)Wing Bolt (Code No. 301-806) ..........................................................................................4

(12)23 mm Wrench (Code No. 323-295) .................................................................................1

English

OPTIONAL ACCESSORIES …………… sold separately

(1)Template Guide (2)Trimmer Guide (Code No. 956-794)

(3)Chuck Sleeve

NOTE:

Specifications are subject to change without any obligation on the part of the HITACHI.

Code No. A B C

303 347 19/64" 3/8"

(7.5mm) (9.5mm)

303 348 5/16" 25/64"

(8mm) (10mm)

303 349 23/64" 7/16"

(9mm) (11.1mm)

303 350 25/64" 15/32"

(10mm) (12mm)

303 351 27/64" 1/2"

(10.7mm) (12.7mm)

303 352 15/32" 35/64"

(12mm) (14mm)

303 353 35/64" 5/8" 3/16"

(14mm) (16mm) (4.5mm)

956 790 21/32" 45/64"

(16.5mm) (18mm)

956 932Z 47/64" 25/32"

(18.5mm) (20mm)

303 354 57/64" 15/16"

(22.5mm) (24mm)

956 933Z 1" 1-1/16"

(25.5mm) (27mm)

956 934Z 1-1/8" 1-3/16"

(28.5mm) (30mm)

303 355 1-33/64" 1-37/64"

(38.5mm) (40mm)

Bottom of

sub base

3/8" (9.5mm)

(Code No. 956-928Z)

Français

INFORMATIONS IMPORTANTES DE SÉCURITÉ

Lire et comprendre toutes les précautions de sécurité, les avertissements et les instructions

de fonctionnement dans ce mode d’emploi avant d’utiliser ou d’entretenir cet outil motorisé.

La plupart des accidents causés lors de l’utilisation ou de l’entretien de l’outil motorisé

proviennent d’un non respect des règles ou précautions de base de sécurité. Un accident

peut la plupart du temps être évité si l’on reconnaît une situation de danger potentiel avant

qu’elle ne se produise, et en observant les procédures de sécurité appropriées.

Les précautions de base de sécurité sont mises en évidence dans la section “SECURITE”

de ce mode d’emploi et dans les sections qui contiennent les instructions de fonctionnement

et d’entretien.

Les dangers qui doivent être évités pour prévenir des blessures corporelles ou un

endommagement de la machine sont identifiés par AVERTISSEMENTS sur l’outil motorisé

et dans ce mode d’emploi.

NE JAMAIS utiliser cet outil motorisé d’une manière qui n’est pas spécifiquement

recommandée par HITACHI.

SIGNIFICATION DES MOTS D’AVERTISSEMENT

AVERTISSEMENT indique des situations potentiellement dangereuses qui, si elles sont

ignorées, pourraient entraîner la mort ou de sérieuses blessures.

PRECAUTION indique des situations dangereuses potentilles qui, si elles ne sont pas évitées,

peuvent entraîner de mineures et légères blessures ou endommager la machine.

REMARQUE met en relief des informations essentielles.

La page charge ...

Hitachi M 12SA2 Manuel utilisateur

Marque: Hitachi

Modèle: M 12SA2

Catégorie: Outils électroportatifs

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Hitachi M 12SA2 User manual
español: Hitachi M 12SA2 Manual de usuario

Hitachi M 12SA2 Manuel utilisateur

Ce manuel convient également à

Hitachi M 12SA2 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents